Draft APAC CDRLs.pdf

UNCLASSIFIED

1 | P a g e

Advanced Propulsion Acquisition Contract

(APAC)

Multiple Award Contract (MAC)

Indefinite Delivery Indefinite Quantity (IDIQ)

Contract Data Requirements List (CDRL) General Instructions

SOLICITATION FA8626-25-R-B008

8 January 2026

Propulsions Directorate, Advanced Propulsion Development (APD) Division (AFLCMC/LPA)

2 | P a g e

CONTRACT DATA REQUIREMENTS LIST (CDRL) MODIFICATION MATRIX

This matrix identifies the Contract Data Requirements List (CDRL) changes as implemented by contract modification.

CHANGE AUTHORITY

(ECP No.; MOD No.; etc.)

CDRL REVISION

NUMBER

DATE CRDL/PAGES

REVISED

*Note: The purpose of the Contract Data Requirements List (CDRL) is to provide a standardized method of clear and unambiguously delineating Government’s minimum essential data needs. The CDRL groups all of the data requirements in a single place rather than have them scattered throughout the solicitation or contract. The list of Data Item Description’s (DIDs) listed below contains tailorable CDRLs you may include for individual Delivery/Task orders (DO/TOs); this list is not all inclusive.

TABLE OF CONTENTS

1. SCOPE

2. GENERAL

3. DATA PREPARATION

4. METHOD OF TRANSMITTAL

5. DATA SUBMITTAL APPROVALS

6. REVISIONS TO DATA SUBMITTALS AND RESUBMITTALS OF DATA

7. DOCUMENT REVISIONS

8. DOCUMENTATION MARKING

3 | P a g e

UNCLASSIFIED

9. DATA ACCEPTANCE

10. REFERENCE DOCUMENTS

11. ACRONYMS AND ABBREVIATIONS

12. DISTRIBUTION/MAILING ADDRESS LIST

13. LIST OF POSSIBLE CDRLs (not all encompassing)

CDRL GENERAL NOTES/INSTRUCTIONS

1. SCOPE: This Contract Data Requirements List (CDRL) establishes the data to be delivered by the contractor, and the submittal, approval, and distribution requirements of all the CDRL data items contained herein. The contractor shall utilize best commercial practices and the guidance referenced in paragraph 10 of these general notes/instructions in meeting the requirements of the CDRL.

2. GENERAL: The requirements for the CDRLs are identified in DoD 5010.12 Procedures for the Acquisition and Management of Technical Data. The Data Item Descriptions (DIDs) specified in the CDRLs are in the Acquisition Streamlining & Standardization Information System (ASSIST) Database (https://assist.dla.mil/online/start/index.cfm).

3. DATA PREPARATION:

a. Data submitted by the contractor shall conform to the quality requirements specified on the CDRL for each data item.

b. Data submittals shall be handled in accordance with the DD Form 254 security guidelines. The contractor shall provide data in basic volumes at an unclassified level whenever possible. Where data is classified in nature, the maximum classification level of a basic document shall not exceed the Secret Special Access Required (SAR) level. All classified data beyond that level shall be provided as a separate annex to the document.

c. Data shall be delivered by one of the following methods:

1) Electronic Delivery/Availability – includes delivery/availability of data files via a government approved server or via attachment of electronic files to email messages, as mutually agreed to between the Government and the contractor. Electronic data delivery and access is subject to Government protection/security requirements. Notification of electronic delivery/availability of deliverables shall be sent to Government CO and Program Manager.

2) Other Electronic Formats – data may be provided in appropriate format using media such as CD- ROM or DVD ROM. A document may consist of multiple files, but files should not be compressed or https://assist.dla.mil/online/start/index.cfm

4 | P a g e

UNCLASSIFIED

archived to save space. Exceptions must be arranged with CO. The contractor shall contact the CO for Block 14 DD Form 1423-1 distribution requirements 10 days prior to first delivery for each DD Form 1423-1 delivered by these means. Disc labels shall contain the following information:

CDRL Item No.

Document Title

Submission Date

Author, Company, Phone

File Name(s) and Formats

Distribution Statement

Export-Control Warning Statement

Destruction Notice

Security Markings

3) Text files to the maximum extent possible, shall be submitted as MS-Word file documents with copy and paste capability. Each text file shall have a filename in accordance with the mutually agreed filename conventions. Each MS-Word document and alternate format text document (to the maximum extent possible) shall have populated metadata in accordance with mutually agreed metadata conventions.

All non-text documents (spreadsheet, graphics, database, etc.) shall be accompanied by an MS-Word document as described above. Each non-text document shall have a filename in accordance with mutually agreed filename conventions. Each PowerPoint or Excel document and alternate native format file (to the maximum extent possible) shall have populated metadata in accordance with mutually agreed metadata conventions. Non-text documents, to the maximum extent possible, shall be submitted as PowerPoint or Excel files. Government recognizes that in some cases (e.g., raw data used for Stress Analysis, Engineering Models, etc.) native format is permissible. Contractor shall ensure Government has required training and access to software programs required to view native formats when such formats are used to satisfy requirements of this contract.

4) Shared data items are those items that are developed utilizing the IPT process and are available electronically. Shared data items are not subject to government requirements regarding format, delivery schedule or approval. When shared data items are not or cannot be maintained utilizing the IPT process, the government may decide to convert the previously shared data item to a deliverable data item.

d. All data shall be submitted in the English language.

4. METHOD OF TRANSMITTAL:

5 | P a g e

UNCLASSIFIED

a. All data submittals shall be accompanied by a letter of transmittal, and the Government shall acknowledge receipt and acceptance, where Government approval is required. Copies of all letters of transmittal shall be provided to the CO and CMDM Team. The letter of transmittal shall include as a minimum: (See Attachment 1)

Contractor Point of Contact (POC) Contractor address Date Contract number and program name Letter control number Document control number Document revision level Document date CDRL sequence number DID Number Data Title/Subtitle Reason or frequency of submittal (monthly, draft, final, update, etc.)

List of distribution addressees as identified in Block 14 of the CDRL List all document enclosures

b. If a paper copy of the LT is prepared, a complete list of addressees shall be placed at the end of the LT, annotating the recipients (as identified on the DD Forms 1423-1, Block 14) including the transmittal-letter-only recipients. If submittal is made via e-mail, the list of addressees in the “TO” line shall include the complete list of addressees and shall be considered sufficient.

c. Unless otherwise specified in Block 16 of the DD Form 1423-1, data submittal date is interpreted as the date the Government receives the data. An annual submittal is defined as one submittal within each Calendar Year (January 1st to December 31st). Electronic data available after 1700 Eastern Standard Time shall be considered delivered the next business day. Submittal days are considered workdays unless it’s a Saturday delivery, then it would be a Friday submittal, if a Sunday delivery, then it would be Monday. For submittal days which fall on Government holidays (as defined by OPM); When the holiday falls on a Monday, then submittal is due the next workday. When the holiday falls on Tuesday through Friday, the submittal is due the day prior.

The six (6) shared holidays (New Years Day, Memorial Day, 4th of July, Labor Day, Thanksgiving Day and Christmas) are not considered workdays and shall not be used when determining submittal due dates.

The non-share holidays (Martin Luther King Day, Presidents Day, Juneteenth, Columbus Day and Veterans Day) are considered workdays when determining submittal due dates.

d. For each data item in the CDRL, the Contractor shall clearly state in the final transmittal letter that this is the last submittal being made and that all contractual requirements concerning that data item have been fulfilled.

e. For each data item the Configuration/Data Manager shall receive a notification of delivery of the data regardless of data type.

5. DATA SUBMITTAL AND APPROVALS:

6 | P a g e

UNCLASSIFIED

The following definitions apply to Block 8 of the DD Form 1423-1:

a. The use of an “A” in Block 8 indicates that Government approval of the identified document is required to assure that the contractor is sufficiently prepared to proceed to the next phase of the contract in addition to verifying compliance with the DID and CDRL requirements. Unless otherwise specified in the DD Form 1423-1 as calculated by working or business days, data item due dates to the Government are calculated by calendar days. Working days are defined as Monday -Friday. Except for the Government Holidays that are called out by OPM. Unless otherwise specified in an individual CDRL, all submittals of a CDRL with an “A” in Block 8 require approval. Any change to an already approved final data submission also requires Government Approval. Unless otherwise specified on the DD Form 1423-1, the technical office noted in Block 6 will review the data submitted for approval and the CO will notify the contractor of approval, disapproval, or corrective action required within 30 calendar days after receipt of data submittal. If the program office cannot respond within the 30 calendar days, the contractor will be notified, and a new suspense date will be mutually established. If the program office has not provided approval/disapproval/intent to extend due date within the 30 calendar days, the data will be considered automatically approved. However, the contractor shall notify the program office via telecom or email prior to assuming approval.

b. If Block 8 has an “N” or is left “blank” these data items are considered non-approval, however, this does not relieve the Contractor of the responsibility of compliance with applicable regulations, standards, procedures, etc. All data submissions are subject to review by the procuring agency for departure of said compliance. The presence or absence of an “A” in Block 8 does not relieve the contractor of the responsibility of full contractual compliance and all data will be subject to review and acceptance by the Government.

c. Data submittal requirements shall not be considered to have been met until the procuring agency has determined that all contractual requirements have been met regarding the identified data.

6. REVISION TO DATA SUBMITTALS AND RESUBMITTALS OF DATA:

a. Unless otherwise specified, data submittals that are disapproved by the Government shall be revised and resubmitted by the contractor within 30 calendar days after receipt of CO letter. If the contractor cannot resubmit within 30 calendar days, the CO shall be notified withing 15 calendar days after receipt of CO letter and a new mutually agreed upon suspense date will be established.

b. Data submittals that require corrective action shall be revised and distributed within 30 calendar days after receipt of CO letter, or as specified in the delivery requirements of the applicable DD Form 1423-1.

If the contractor cannot resubmit within the required time, the CO shall be notified within 15 calendar days after receipt of CO letter and a new mutually agreed upon suspense date will be established. The CO will notify the contractor of approval, or further corrective action required for the previously submitted corrective actions, within 30 calendar days after receipt of resubmittal.

7. DOCUMENT REVISIONS:

7 | P a g e

UNCLASSIFIED

The Contractor shall comply with the following requirements in the revision of the documents provided in response to the data requirements specified in the CDRL.

a. When resubmission of data is requested, complete documents shall be submitted unless otherwise specified.

b. A “revisions” page shall be provided in the front of each revision and shall contain, as a minimum:

1) A brief description of the reason for revision, including the applicable authority, e.g., ECP, Change order, supplemental agreement.

2) Revision identification letter or number and revision date.

3) Appropriate administrative instructions, e.g., security information, revision instructions, etc.

c. Each revised page shall have the specific changes identified by a dark vertical line in the margin and include appropriate identification to the applicable revision by either date, revision number, or letter.

d. Each revised page shall contain the revision number or letter in the upper right corner of the page.

e. Anytime a revision is submitted, the title page of the document shall indicate the number or letter and date of that revision. Latest revision symbol and date shall be visible on the front surface of the document.

f. The letter of transmittal for each revision shall reference all previous/pertinent correspondence relating to the documentation being submitted.

8. DOCUMENTATION MARKING:

DoD instruction 5230.24, Distribution Statements on Technical Documents, provides policy and guidance on marking documents. Air Force Instruction (AFI) 61-204, Disseminating Scientific and Technical Information, specifies certain distribution statements to be used on data to control distribution by Government agencies such as the Defense Technical Information Center (DTIC).

a. Block 9 of the DD Form 1423-1 annotates the relevant distribution statement applicable to the data to be submitted. This distribution statement shall have precedence over other technical documentation on this Contract, unless otherwise specified. As annotated in Block 9 of the DD Form 1423-1, one of the following distribution statement(s) shall apply to all data on this contract:

DISTRIBUTION STATEMENTS:

(1) Distribution Statement A. Approved for public release.

(a) This statement may be used only on unclassified technical documents that have been cleared for public release by competent authority in accordance with DoD Directive 5230.09 and DoD Instruction 5230.29. Technical documents resulting from contracted fundamental research efforts will normally be assigned Distribution Statement A, except for those rare and exceptional circumstances where there is a high likelihood of disclosing performance characteristics of military systems, or of manufacturing technologies that are unique and critical to Defense, and agreement on this situation has been recorded in the contract or grant.

(b) Technical documents with this statement may be made available or sold to the public and foreign nationals, companies, and Governments, including adversary Governments, and may be exported.

8 | P a g e

UNCLASSIFIED

(c) This statement shall not be used on classified technical documents or documents containing export-controlled technical data as provided in DoD Directive 5230.25.

(d) This statement shall not be used on technical documents that formerly were classified unless such documents are cleared for public release in accordance with DoD Directive 5230.25.

(2) Distribution Statement “B” – Distribution authorized to U.S. Government agencies only, (fill in reason) (date of determination). Other requests for this document shall be referred to AFLCMC, 2450 D Street, Bldg. 20, WPAFB, OH 45433.

(3) Distribution Statement “C” – Distribution authorized to U.S. Government agencies and their contractors, (fill in reason) (date of determination). Other requests for this document shall be referred to AFLCMC, 2450 D Street, Bldg. 20, WPAFB, OH 45433.

(4) Distribution Statement “D” – Distribution authorized to Department of Defense and U.S. DoD contractors only; (fill in reason) (date of determination). Other requests for this document shall be referred to AFLCMC, 2450 D Street, Bldg. 20, WPAFB, OH 45433.

(5) Distribution Statement “E” – Distribution authorized to DoD components only, (fill in reason) (date of determination). Other requests for this document shall be referred to AFLCMC, 2450 D Street, Bldg.

20, WPAFB, OH 45433.

(6) Distribution Statement “F” – Further dissemination only as directed by AFLCMC, 2450 D Street, Bldg. 20, WPAFB, OH 45433, (date of determination), or higher DoD authority.

(a) Export-Controlled Warning Statement: Besides a distribution statement, the marking system also requires the use of a warning notice on all documents that contain export controlled technical data.

That notice may be used in conjunction with any of the five limited distribution statements (“B”, “C”, “D”, “E” and “F”) Statement A: which authorizes public release, cannot be used in conjunction with the export-control warning notice. Procedures for dissemination of this technical data outside of the U.S. Government are contained in the DoD Directive 5230.25.

WARNING _ This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec. 2751, et seq) or the Export Administration Act of 1979 Title 50, U.S.C., App 2401 et seq.) as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with the provisions of DoD Directive 5230.25.

When it is technically infeasible to use the entire statement, an abbreviated marking may be used, and a copy of the full statement added to the “Notice to Accompany Release of Export -Controlled Data” required by DoD Directive 5230.25.

(b) Contractor Imposed Distribution Statements. Part 27, Subpart 27.4 to the DoD Supplement to the Federal Acquisition Regulations (FAR) stipulates control procedures for contractor-controlled technical data to which the Government has limited rights. These procedures shall be followed as described in AFI 61-204.

(c) DESTRUCTION NOTICE – For classified documents, mark documents with the following statement “DESTRUCTION NOTICE” – Follow the procedures in DoD 5220.22-M, National Industry Security Program Operating Manual (NISPOM), section 5-705, or DoDM 5200.01, V3 DoD Information Security Program.” For unclassified, limited documents (i.e., not approved for

9 | P a g e

UNCLASSIFIED

public release) mark documents with the following statement “DESTRUCTION NOTICE – Destroy by any method that will prevent disclosure of contents or reconstruction of the document.”

(d) The Contractor is responsible for ensuring adequate marking and security measures are in place to prevent unauthorized access to electronic data. The Contractor is not authorized to provide copies of any data on the CDRL to activities who are not specifically identified in the distribution block of the CDRL without written Government approval from the Program Office.

9. DATA ACCEPTANCE: The contractor shall prepare and submit a final DD Form 250 on a one-time basis collectively accounting for all completed Exhibit Line/Subline Items which call for a submission of the data by letter of transmittal. The DD Form 250 shall include a list and an account of all data submitted by letter of transmittal and approved by the Government during the reporting period. The DD Form 250 is due at the end of the contract.

10. REFERENCE DOCUMENTS (for guidance purposes):

a. DoD 5010.12-M, Procedures for the Acquisition and Management of Technical Data, May 1993

b. DoD Instruction 5230.24, Distribution Statements on DoD Technical Information, January 10, 2023

c. Acquisition Streamlining and Standardization Information System (ASSIST)

d. DoDI 5230.09, Clearance of DoD Information for Public Release, January 25, 2019; chg. 1 dated February 9, 2022

e. DoD Directive 5400.07, DoD Freedom of Information Act (FOIA) Program, April 5, 2019

f. DoD Directive 5230.25, Change 2, Withholding of Unclassified Technical Data from Public Disclosure, November 6, 1984, Change 2 October 15, 2018

g. DoD Manual 5200.01 V1, DoD Information Security Program: Overview, Classification and Declassification, February 24, 2021, Chg. 2 July 28, 2020

h. DoD Instruction 5200.48, Controlled Unclassified Information (CUI), March 6, 2020

i. DoDD 5220.22-M, Procedures for the Acquisition and Management of Technical Data, May 1993

j. 32 CFR Part 117, National Industrial Security Program Operating Manual (NISPOM), 24 February 2021

k. DoDI 5230.24, Distribution Statements on Technical Documents, 10 January 2023

11. ACRONYMS AND ABBREVIATIONS: Acronyms and abbreviations utilized in this General Notes/Instructions document are identified below:

AFI Air Force Instruction

ASSIST Acquisition Streamlining and Standardization Information System

CDRL Contract Data Requirements List

CO Contracting Officer

DID Data Item Description

DoD Department of Defense

10 | P a g e

UNCLASSIFIED

DTIC Defense Technical Information Center

ECP Engineering Change Proposal

FAR Federal Acquisition Regulations

ITAR International Traffic in Arms Regulation

IPT Integrated Product Team

OPM Office of Personnel Management

SAR Special Access Required

12. DISTRIBUTION/MAILING ADDRESS LIST: Data shall be delivered electronically to AFLCMC/LP Configuration/Data Management. CDRL addressee updates will be forwarded to Contractor’s Data Management Office as required.

ATTACHMENT 1

EXAMPLE TRANSMITTAL LETTER

To: AFLCMC/LPA 2450 D Street, Building 20 Wright Patterson AFB, OH 45433

Attention: LPK Contracting Officer Name LPA Program Manager Name LPA Configuration Manager

Subject: FAXXX-XX-X-XXX, Collaborative Combat Aircraft (CCA), Exhibit A, Submittal of Contracts Data Requirements List (CDRL), CXXX, CDRL Title

References: Contract Number, CDRL CXXX, CDRL Title

Enclosure: (1) CDRL CXXX, CDRL Title, Document Number, Rev, Document date

1. In accordance with Reference (a) COMPANY NAME HERE, hereby submits the documentation denoted in Enclosure

(1) by electronic submission in accordance with the subject contract data submittal requirements. COMPANY NAME HERE respectfully requests the Governments approval no later than DUE DATE HERE, as specified in the referenced CDRL, Block 8 of the DD Form 1423-1.

If you have questions, please contact the undersigned at PHONE NUMBER or via Email at Email address here.

Your signature Block

13. List of possible delivery items:

Data Item

Data Item Description (DID) Title

DID #

11 | P a g e

UNCLASSIFIED

A001 Acquisition & Sustainment Data Package (ASDP) – Configuration Status Accounting (CSA) Information

DI-SESS-82333

A002 Acquisition & Sustainment Data Package (ASDP) - Digital Specification Development and Verification Criteria

DI-PSSS-82464

A003 Acquisition and Sustainment Data Package (ASDP) - Functional Thread Analysis (FTA) Report

MGMT-2023-004

A004 Acquisition and Sustainment Data Package (ASDP) - Product Engineering Design Data and Associated Lists (EDDAL)

DI-SESS-82351

A005 Airworthiness Directives/Service Bulletins/Advisory Data DI-MISC-81241 A006 Assessment of Manufacturing Risk and Readiness DI-SESS-81974 A007 Bar Code Identification Report IUID Data for Embedded Components DI-MGMT-80177B/T A008 Bill of Material (BOM) for Logistics and Supply Chain Risk Management DI-PSSS-81656B A009 Computer Software Product End Items Control Logic, Lifting Algorithms & Trending

Logic

DI-AVCS-80700A

A010 Computer Software Product End Items / Hardware Geometry and Engine Test Data DI-AVCS-80700A (Dup w/above #)

A011 Conference Agenda DI- ADMN-81249 A012 Conference Minutes / Action Items DI-ADMN-81250C/T A013 Configuration Audit Plan (SVR/FCA/PCA/Audit Plan) DI-SESS-81646/T A014 Configuration Item (CI) Documentation Recommendation DI-SESS-82007B A015 Configuration Status Accounting Information DI- CMAN-81253A/T A016 Container Design Retrieval System (CDRS) Data Input DI- PACK-80684B/T A017 Contract Change Proposals (CCPS) DI- ADMN-81401 A018 Contract Funds Status Report (CFSR) DI-MGMT-81468A/T A019 Contract Performance Report (CPR) DI-MGMT-81466A/T A020 Contract Work Breakdown Structure DI-MGMT-81334D A021 Contract Work Breakdown Structure (CWBS) / Cost and Software Data Report

(CSDR)

DI-MGMT-81334C/T

A022 Contractor Business Data Report (DD Form 1921-3) / Cost and Software Data Report

(CSDR)

DI-FNCL-81765A/T

A023 Contractor Sustainment Report (DD Form 1921-4) DI-FNCL-81831 A024 Contractor Configuration Management Plan (CCMP) DI-CMAN-80858B/T A025 Contractor Risk Management Plan DI-MGMT-81808/T A026 Contractor Support Plan DI-MGMT-82363A A027 Cost and Hour Report (Flex File) Cost and Software Data Reporting DI-FNCL-82162 A028 Cost Data Summary Report (DD Form 1921) Cost and Software Data Report (CSDR) DI-FNCL-81565B/T A029 Critical Safety Item, Characteristic and Critical Defect Report DI-SAFT-80970A A030 Data Accession List (DAL) DI-MGMT-81453C A031 Digital Imaging DI-MISC-81579 A032 Digital System Model DI-SESS-82364 A033 Digital Twin Description DI-SESS-82483 A034 Engineering Change Proposal (EDP) DI-CMAN-80639C/T A035 Facilities Plan – Facility Requirement Plan DI-FACR-80976/T A036 Failure Mode, Effects and Criticality Analysis Report DI-SESS-81495B A037 Frequency Allocation Data DI-MISC-81174

12 | P a g e

UNCLASSIFIED

A038 Functional Cost-Hour Report DD Form 1921-1/Cost and Software Data Report

(CSDR)

DI-FNCL-81566B/T

A039 Gas Turbine Engine Steady State and Transient Performance Present for Computer Programs

DI-MSSM-81966A

A040 Hazardous Material Management Program (HMMP) Report ESOH Program Report DI-MISC-81397A/T A041 Hazardous Material Management Program (HMMP) Plan DI- MISC-81398A/T A042 Health Hazard Assessment Report (HHAR) OEHHA DI-SAFT-80106 A043 Human Systems Integration Program Plan DI-HFAC-81743 A044 Integrated Logistics Support Plan (ILSP) DI-ILSS-80095 A045 Integrated Master Schedule (IMS) DI-MGMT-81650/T A046 Interface Control Document Model (ICM) DI-SESS-81248B A047 Integrated Program Management Report (IPMDAR) DI-MGMT-81861C/T A048 Logistics Management Information (LMI) Data Products Provisioning Technical

Documentation (PTD)

DI-ALSS-81529

A049 Logistics Management Information (LMI) Summaries DI-ALSS-81530 A050 Logistics Management Information (LMI) Summaries / Availability and Mission

Capability Analysis Plan

DI-ALSS-81530/T

A051 Logistics Plan DI-SESS-82178 A052 Maintenance and Repair Parts Data Report DI-MGMT-82163 A053 Maintenance Test and Support Equipment Requirements List DI-SESS-80294B A054 Management Plan - Engine Life Management Plan DI-MGMT-80004A/T A055 Management Plan - Integrated Digital Environment (IDE) Training DI-MGMT-80004A/T A056 Management Plan - Integrated Master Plan DI-MGMT-80004A/T A057 Management Plan - Risk Management Plan DI-MGMT-80004A/T A058 Manufacturing and Quality Assurance Status Report (MQASR) DI-QCIC-82323/T A059 Mass Properties Control and Management Process (MPCMP) Plan DI-MGMT-81452A A060 Material Improvement Project Report DI-MGMT80258A/T A061 Model-Based Engineering Failure Models, Effects, and Criticality Analysis Profile DI-SESS-82426 A062 Notice of Revision (NOR) DI-CMAN-80642 A063 Operations Security (OPSEC) Plan DI-MGMT-80934C/T A064 Phased Support Plan DI-ALSS-80037 A065 Presentation Material DI-ADMN-81373/T A066 Preservation and Packing Data DI-PACK-80120B/T A067 Product Engineering Design Data and Associated List (EDDAL) DI-SESS-81000F A068 Request for Deviation (RFD) Variance DI-CMAN-80604C/T A069 Request for Nomenclature (DD Form 61) DI-CMAN-81254 A070 Proposed Spare Parts List DI-ILSS-80134 A071 Quantity Data Report Cost, Software and Technical Data Reporting DI-MGMT-82164 A072 Reliability and Maintainability (R&M) Program Plan DI-SESS-81613 A073 Requirements Traceability Verification Matrix (RTVM) DI-MGMT-82133 A074 Risk Management Status Report DI-MGMT-81809 A075 Safety Assessment Report (SAR) DI-SAFT-80102C/T A076 Significant Historical Data (Engine) DI-MGMT-81564/T A077 Small Business Subcontract Report DI-MGMT-81642

13 | P a g e

UNCLASSIFIED

A078 Small Business Utilization Report DI-MGMT-82041B A079 Specification Change Notice (SCN) DI-SESS-80643E A080 Software Development Plan (SDP) / Software Development Integrity Master Plan DI-IPSC-81427B A081 Software Resources Data Reporting (SRDR): Initial Development / Cost and Software

Data Report (CSDR)

DI-MGMT-81739/T

A082 Software Resources Data Reporting (SRDR): Final Development / Cost and Software Data Report (CSDR)

DI-MGMT-81740/T

A083 Software Resources Data Reporting (DD Form 3026-1) DI-MGMT-82035A A084 Software Resources Data Reporting (DD Form 3026-2) DI-MGMT-82035A A085 Software Resources Data Reporting (DD Form 3026-3) DI-MGMT-82035A A086 Status Report – See Blk 16 DI-MGMT-80368A/T A087 Supplemental Data for Provisioning (SDFP) DI-ALSS-81557 A088 Sustainment Functional Cost-Hour Report (DD From 1921-5) – Cost and Software

Data Report (CSDR)

DI-FNCL-81992

A089 System Baseline Report DI-PSSS-82260 A090 System Deficiency Report (SDR) Data DI-MISC-81627 A091 Systems Engineering Management Plan (SEMP)

Systems Engineering Plan (SEP)

DI-SESS-81785B

A092 System Safety Hazard Analysis Report (SSHAR) DI-SAFT-80101C/T A093 System Safety Program Plan (SSPP) DI-SAFT-81626/T A094 Technical Data Package DI-SESS-80776B A095 Technical Data Report Cost, Software and Data Reporting DI-MGMT-82165 A096 Technical Report - Study/Services Anti-Tamper Program Plan DI-MISC-80508B/T A097 Technical Report - Study/Services Comprehensive Adaptive Prototyping Plan (CAPP) DI-MISC-80508B/T A098 Technical Report - Study/Services Digital Engineering Style Guide DI-MISC-80508B/T A099 Technical Report-Study/Services Digital Engineering Master Plan (DEMP) DI- MISC-80508B/T A100 Technical Report - Study/Services Electro-magnetic Environment Plan and Report A101 Technical Report-Study/Services Government Reference Architecture (GRA) DI-MISC-80508B/T A102 Technical Report - Study/Services Information Assurance DI-MISC-80508 A103 Technical Report - Study/Services Logistics Composite Model Report and Database DI-MISC-80508 A104 Technical Report - Study/Services Manufacturing Program Plan DI-MISC-80508B/T A105 Technical Report - Study/Services NEPA Facilitation Report DI-MISC-80508 A106 Technical Report - Study/Services PESHE Facilitation Report DI-MISC-80508 A107 Technical Report - Study/Services Propulsion System Integrity Program (PSIP) Master

Plan

DI-MISC-80508B/T

A108 Technical Report - Study/Services Studies and Plans DI-MISC-80508B/T A109 Technical Report - Study/Services System Supportability Report DI-MISC-80508B/T A110 Technical Report – Study/Services Technology Maturation Plan and Report DI-MISC-80508B/T A111 Tempest Control Plan DI-MGMT-81026/T A112 Test Facility Requirements Document (TFRD) DI-FACR-80810A/T A113 Test Information Sheet (TIS) DI-QCIC-81536/T A114 Test/Inspection Report DI-NDTI-80809B/T A115 Test/Inspection Report Subsystem/Component Test Report DI-NDTI-80809B A116 Test Plan – Detailed Test Plan DI-NDTI-80566A/T A117 Test Plan - Engine and Subsystem Test Plan DI-NDTI-80566A/T

14 | P a g e

UNCLASSIFIED

A118 Test Procedure DI-NDTI-80603A/T A119 Transportation Data Report – Classified Items DI-PACK-80877 A120 Vulnerability Analysis Report DI-MISC-80564/T