09960 High Performance Coatings.doc

Floor Coating IDIQ Hill AFB, UT

Copyright 2003 by The American Institute of Architects (AIA)

Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA

SECTION 09960 - HIGH-PERFORMANCE COATINGS

This Section uses the term "Architect." Change this term to match that used to identify the design professional as defined in the General and Supplementary Conditions.

Verify that Section titles referenced in this Section are correct for this Project's Specifications; Section titles may have changed.

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes surface preparation and application of high-performance coating systems on the following substrates:

Adjust lists below to suit Project.

1. Exterior Substrates:

a. Concrete, vertical, and horizontal surfaces.

b. Clay masonry.

c. Concrete masonry units (CMU).

2. Interior Substrates:

a. Concrete, vertical and horizontal surfaces.

b. Clay masonry.

c. Concrete masonry units (CMU).

B. Related Sections include the following:

List below only products that the reader might expect to find in this Section but are specified elsewhere.

1. Division 1 Section "LEED Requirements" for additional LEED requirements.

Primers in other Sections must be coordinated for compatibility with finish coats specified in this Section. Review other Sections for shop-primed products and insert references to Section 09960 to establish primer requirements.

2. Division 5 Sections for shop priming of metal substrates with primers specified in this Section.

3. Division 9 painting Sections for special-use coatings and general field painting.

1.3 SUBMITTALS

A. Product Data: For each type of product indicated.

B. Samples for Initial Selection: For each type of finish-coat product indicated.

Delete paragraph above if colors and other characteristics are preselected and specified or scheduled. Retain first paragraph and subparagraphs below with or without above.

C. Samples for Verification: For each type of coating system and in each color and gloss of finish coat indicated.

1. Submit Samples on rigid backing, 8 inches square.

2. Step coats on Samples to show each coat required for system.

3. Label each coat of each Sample.

4. Label each Sample for location and application area.

D. Product List: For each product indicated. Cross-reference products to coating system and locations of application areas. Use same designations indicated on Drawings and in schedules.

Retain paragraph below if low-emitting materials are required for LEED Credit EQ 4.2; coordinate with requirements selected in Part 2 for paints and coatings.

E. LEED Submittals: For Credit EQ 4.2, manufacturers' product data for coatings, including printed statement of VOC content and chemical components.

1.4 QUALITY ASSURANCE

A. Master Painters Institute (MPI) Standards:

1. Products: Complying with MPI standards indicated and listed in "MPI Approved Products List."

For renovation projects, consult "MPI Maintenance Repainting Manual" and revise subparagraph below and coating systems specified in Part 3.

2. Preparation and Workmanship: Comply with requirements in "MPI Architectural Painting Specification Manual" for products and coating systems indicated.

Delete paragraph and subparagraphs below if not required.

B. Mockups: Apply benchmark samples of each coating system indicated to verify preliminary selections made under sample submittals and to demonstrate aesthetic effects and set quality standards for materials and execution.

1. Architect will select one surface to represent surfaces and conditions for application of each type of coating and substrate.

a. Wall and Ceiling Surfaces: Provide samples of at least 10 sq. ft.

b. Other Items: Architect will designate items or areas required.

2. Apply benchmark samples after permanent lighting and other environmental services have been activated.

3. Final approval of color selections will be based on benchmark samples.

a. If preliminary color selections are not approved, apply additional benchmark samples of additional colors selected by Architect at no added cost to Owner.

1.5 DELIVERY, STORAGE, AND HANDLING

A. Store materials not in use in tightly covered containers in well-ventilated areas with ambient temperatures continuously maintained at not less than 45 deg F.

1. Maintain containers in clean condition, free of foreign materials and residue.

2. Remove rags and waste from storage areas daily.

If necessary, add special requirements for fire protection, heating, ventilation, and other conditions for storage areas on-site.

1.6 PROJECT CONDITIONS

Some manufacturers' products may require higher temperatures for proper curing. Consult manufacturers and revise first paragraph below to suit requirements for specific products if necessary.

A. Apply coatings only when temperature of surfaces to be coated and surrounding air temperatures are between 50 and 95 deg F.

B. Do not apply coatings in snow, rain, fog, or mist; when relative humidity exceeds 85 percent; at temperatures less than 5 deg F above the dew point; or to damp or wet surfaces.

1.7 EXTRA MATERIALS

Extra materials may not be allowed for publicly funded projects.

A. Furnish extra materials described below that are from same production run (batch mix) as materials applied and that are packaged for storage and identified with labels describing contents.

Retain subparagraph below for projects that require only limited quantities of extra materials. If necessary, replace percentage with a specific number of gallons (liters) or cases and include an expanded description of the quantity of each material and color.

1. Quantity: Furnish an additional 0.5 gal of each material and color applied.

PART 2 - PRODUCTS

To efficiently edit Part 2, first edit Exterior High-Performance Coating Schedule and Interior High-Performance Coating Schedule in Part 3. Then retain, delete, and insert appropriate products in Part 2 to correspond with coating systems specified in Part 3.

2.1 HIGH-PERFORMANCE COATINGS, GENERAL

A. Material Compatibility:

Systems could fail if coatings are incompatible. MPI's coating systems match primers and topcoats, taking compatibility into consideration.

1. Provide materials for use within each coating system that are compatible with one another and substrates indicated, under conditions of service and application as demonstrated by manufacturer, based on testing and field experience.

If retaining subparagraph below, coordinate products retained, if any, in other Part 2 articles, to ensure that one manufacturer can provide products for an entire system.

2. Provide products of same manufacturer for each coat in a coating system.

Retain paragraph and subparagraphs below if low-emitting materials are required for LEED Credit EQ 4.2; coordinate with products selected. Below is based on chemical component limitations and restrictions in Green Seal's GS-11. For names of products that comply, see products listed as LEED compliant for VOCs in "MPI Approved Products List" (available at www.paintinfo.com).

B. Chemical Components of Interior Paints and Coatings: Provide products that comply with the following limits for VOC content when calculated according to 40 CFR 59, Subpart D (EPA Method 24) and the following chemical restrictions:

1. Flat Paints and Coatings: VOC content of not more than 50 g/L.

2. Non flat Paints and Coatings: VOC content of not more than 150 g/L.

3. Anticorrosive Coatings: VOC content of not more than 250 g/L.

4. Stains: VOC content of not more than 250 g/L.

5. Aromatic Compounds: Paints and coatings shall not contain more than 1.0 percent by weight of total aromatic compounds (hydrocarbon compounds containing 1 or more benzene rings).

6. Restricted Components: Paints and coatings shall not contain any of the following:

a. Acrolein.

b. Acrylonitrile.

c. Antimony.

d. Benzene.

e. Butyl benzyl phthalate.

f. Cadmium.

g. Di (2-ethylhexyl) phthalate.

h. Di-n-butyl phthalate.

i. Di-n-octyl phthalate.

j. 1,2-dichlorobenzene.

k. Diethyl phthalate.

l. Dimethyl phthalate.

m. Ethylbenzene.

n. Formaldehyde.

o. Hexavalent chromium.

p. Isophorone.

q. Lead.

r. Mercury.

s. Methyl ethyl ketone.

t. Methyl isobutyl ketone.

u. Methylene chloride.

v. Naphthalene.

w. Toluene (methylbenzene).

x. 1,1,1-trichloroethane.

y. Vinyl chloride.

Color selection is often limited because some coating materials yellow or degrade under some environmental conditions.

C. Colors: As selected by Project Manager from manufacturer's full range.

2.2 BLOCK FILLERS

Coordinate products retained in this Article with substrates and coating systems retained in Part 3.

A. Interior/Exterior Latex Block Filler: MPI#4.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Moorcraft, Super Craft Latex Block Filler, 285-01.

b. Bennette Paint Mfg. Co., Inc.; Int/Ext Acrylic Latex Block Filler, 32-4.

c. Cloverdale Paint; Latex Block Filler, 5700.

d. Columbia Paint & Coatings; High Performance, Int/Ext Acrylic Latex Block Filler, 05-055-PP.

e. Coronado Paint; Super Kote 5000, Commercial Latex Block Filler, 946-11.

f. Flex Bon Paints; Int.-Ext. 100% Acrylic Block Filler, 1151.

g. General Paint; Block Filler, 70-224.

h. ICI Paints; Prep-N-Prime, Block Filler, 3010, Devoe/Fuller, Devoe-Fill, DV52903, or Devoe Coatings, Bloxfil Acrylic Block Filler, 4000.

i. Kelly-Moore Paints; Fill and Prime Acrylic Block Filler, 521.

j. Kwal-Howells Paint; Accu-Pro, Blok-Fil, 5890.

k. Miller Paint; Ext. Block Filler, 6015.

l. PARA Paints; Commercial Latex Block Filler, 5792.

m. PPG Architectural Finishes, Inc.; Interior/Exterior Latex Block Filler, 6-12.

n. Sherwin-Williams Company (The); PrepRite, Int/Ext Block Filler, B25W25.

o. Sico, Inc.; Sico Expert, Interior Latex Block Filler, 675-115.

p. Vista Paint; Block Kote, 040.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

B. Epoxy Block Filler: MPI #116.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Cloverdale Paint; Epoxy Block Filler, 83065.

b. Columbia Paint & Coatings; Insl-x, Epoxy Block Filler, EXP 120.

c. Coronado Paint; Polyamide Epoxy Block Filler, 101-11.

d. Diamond Vogel Paints; V-Cote 100, Acrylic Epoxy Block Filler, MC-1234.

e. Frazee Paint; Ameron, Amerlock 400 BF, 400 BF.

f. General Paint; Ameron, Amerlock Block Filler, 400BF.

g. ICI Paints; Devoe Coatings, Devran 224HS, 224HS, Devoe Coatings, Bar-Rust 231, 231, or Devoe Coatings, Bar-Rust 236, 236.

h. Miller Paint; PPG Aquapon, Polyamide Epoxy Block Filler, 97-685 Series.

i. PARA Paints; Insl-x, Epoxy Blockfiller, EXP 120.

j. Parker Paint Mfg. Co. Inc.; Ameron, Amerlock 400 BF, 400BF.

k. PPG Architectural Finishes, Inc.; Aquapon, Epoxy Block Filler, 97-685.

l. Rodda Paint Co.; Carboline, Carboguard 954HB.

m. Sherwin-Williams Company (The); Industrial & Marine, Kem Cati-Coat HS Epoxy Filler/Sealer, B24W400/V400 S.

n. Spectra-Tone; Insl-x, Epoxy Block Filler, EXP 120.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

2.3 INTERIOR PRIMERS/SEALERS

Coordinate products retained in this Article with substrates and coating systems retained in Part 3.

A. Interior Latex Primer/Sealer: MPI #50.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Regal, First Coat Latex Primer/Undercoater, 216 or Moorcraft, Latex Undercoater & Primer Sealer, 253-00.

b. California Paints; ProPrime, Latex Primer White, 54500.

c. Cloverdale Paint; Interior Latex Primer Sealer, 05250.

d. Columbia Paint & Coatings; Premium Pro, Interior Latex Enamel Undercoater, 02-735-PP or Insl-x, Waterbase Primer/Sealer/Stain Killer, AQ-0500.

e. Coronado Paint; Super Kote 5000, Latex Primer-Sealer, 40-11.

f. Dunn-Edwards Corporation; Eff-Stop, Acrylic Masonry Primer/Sealer, W 709.

g. Duron Inc.; Interior Acrylic Drywall Primer, 04-124 or Latex Undercoater, 04-123.

h. Farrell-Calhoun; Perfik-Seal, Interior Latex Primer-Sealer, 380.

i. Flex Bon Paints; Interior Alkyd Latex Primer, 1071.

j. Frazee Paint; Aqua Seal, Interior Vinyl Acrylic Wall Sealer, 061.

k. General Paint; Breeze, Super Seal Latex, 51-087 orTradesman, Latex Sealer, 28-080].

l. Hirshfield's, Inc.; Hirsfield's Paint Manufacturing, Drywall Primer Interior Latex, 1250.

m. ICI Paints; Prep-N-Prime, PVA Interior Primer Sealer, 1030, Prep-N-Prime, Interior Latex Wall Primer, 1000 or Devoe/Fuller, Wonder-Tones, DR50801.

n. Insl-x; Aqualock, Waterbase Primer/Sealer/Stain Killer, AQ-0500.

o. Iowa Paint Manufacturing Company, Inc.; Prime Line, Hi Hide PVA Primer, 516.

p. Kelly-Moore Paints; Acry-Prime, Interior Latex Primer Sealer, 971 or Enviro-Cote, Interior Latex Primer, 1505.

q. Kwal-Howells Paint; Accu-Pro, Interior Latex Flat Drywall Primer, 0890.

r. Miller Paint; Kril Primer Sealer, 6040.

s. Mills Paint; Superior Quality, Interior Latex Primer Sealer, 133.

t. Northern Paint; Colorlox, Hi Hide Latex Primer, 301-49.

u. PARA Paints; Prime Tech Hi-Hide Latex Primer, 5799.

v. Porter Paints; Interior Latex Sealer, 37725.

w. PPG Architectural Finishes, Inc.; Speedhide, Int. Latex Primer Sealer, 6-2.

x. Rodda Paint Co.; Scotseal, Heavy Bodied Latex Sealer, 50 7801 1.

y. Sherwin-Williams Company; PrepRite, 200 Latex Primer, B28W200 or Quali-Kote, Interior Latex Primer, B28WQ8001.

z. Spectra-Tone; Jobmaster, PVA Latex Primer Sealer, 74.

aa. Vista Paint; Seal Cote, 155.

If retaining requirements for environmental characteristics below, coordinate with products retained above.

3. Environmental Characteristics:

a. VOC Content:

1) Minimum E Range of E2.

2) Meets or exceeds LEED requirements for VOC content.

b. Environmental Performance Rating (EPR): Minimum EPR 2.

B. Interior Alkyd Primer/Sealer: MPI #45.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Moorcraft, Super Spec Alkyd Primer Sealer, C245 or Fresh Start, Int/Ext All Purpose Alkyd Primer, 024.

b. Bennette Paint Mfg. Co., Inc.; Interior Alkyd Primer Sealer, 32-45.

c. California Paints; Fres-Coat, Premium Int. Alkyd Primer Sealer, 20200.

d. Cloverdale Paint; Interior Enamel Undercoat, 15100.

e. Columbia Paint & Coatings; Industrial, Master Prime Interior Alkyd, 03-792-PP.

f. Coronado Paint; Super Kote 5000, Alkyd Primer Undercoater, 37-11.

g. Frazee Paint; Fraflo 11, Int. Alkyd Enamel Undercoater, 367.

h. General Paint; Interior Primer Sealer, 02-230.

i. ICI Paints; Devoe/Fuller, Killsatin, DR51601, Devoe/Fuller, Primz, FOB 220-01, or Prep-N-Prime, Stain Jammer Primer Sealer, 1110.

j. Insl-x; Prime Lock, Primer/Sealer/Stain Killer, PS-7000.

k. Kelly-Moore Paints; Flo-Cote, Alkyd Enamel Undercoater, 985-100.

l. Kwal-Howells Paint; Accu-Pro, Alkyd Undercoat, 4200.

m. Miller Paint; Pure Paint Primer, 240.

n. PPG Architectural Finishes, Inc.; Speedhide, Interior Alkyd Primer, 6-6.

o. Sherwin-Williams Company (The); PrepRite, Interior Oil Primer/Undercoater, B49W2.

p. Tower Paint; Interior/Exterior Enamel Undercoat, 375200.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E1.

C. Interior Latex-Based Wood Primer: MPI #39.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Fresh Start, Interior/Exterior Primer, 23.

b. BLP Mobile Paint Manufacturing Company, Inc.; Weather-Tite, 100% Acrylic Latex Universal Primer, 6-6.

c. California Paints; Wipe-Out, Latex Stain Block - White, 52500.

d. Cloverdale Paint; Int./Ext. Acrylic Latex Primer, 5130.

e. Columbia Paint & Coatings; Masterpiece, Acry-Prime Stain Block Primer, 05-200-PP or Insl-x, Aqualock, AQ-0500.

f. Coronado Paint; Grip & Seal Stain Killing Primer, 116-11.

g. Diamond Vogel Paints; Sure Grip, Acrylic Latex Primer, BU-1501/02.

h. Duron Inc.; American Paints, Terminator T2 WB Primer/Sealer, 71-218.

i. Frazee Paint; Prime+Plus, 168.

j. General Paint; Exterior Latex Wood Primer, 70-002.

k. Griggs Paint; 3-1 Stain-Out Primer, 301W47.

l. Hallman Lindsay Quality Paints; Primeguard, Acrylic Exterior Primer, 112.

m. ICI Paints Prep-N-Prime, Gripper Stain Killer Primer, 3210 or Prep-N-Prime, 100% Acrylic Latex Primer, 2000.

n. Insl-x; Aqualock, Waterbase Primer/Sealer/Stain Killer, AQ-0500.

o. Kelly-Moore Paints; Uni-Prime, 295.

p. M.A.B. Paints; Lok Tite Latex Stain Sealer, 056-159.

q. Miller Paint; PPG Seal-Grip; Int/ Ext Stain Blocking Primer, 17-21.

r. Northern Paint; Exterior Acrylic Primer, 30-60.

s. PARA Paints; Blockout, Acrylic Stain Blocking Primer, 888.

t. Parker Paint Mfg. Co. Inc.; Flex Prime, 2333.

u. PPG Architectural Finishes, Inc.; Seal Grip, Plastic Primer (Waterborne), 17-21.

v. Rodda Paint Co.; Lasyn Enamel Undercoat, 503001.

w. Sherwin-Williams Company (The); PrepRite, ProBlock Int/Ext Latex Primer/Sealer, B51W20.

x. Smiland Paint Company; Morwear, Acrylic Stain Blocking Primer, 2098.

y. Spectra-Tone; Insl-x, AquaLock, AQ-0500.

If retaining requirements for environmental characteristics below, coordinate with products retained above.

3. Environmental Characteristics:

a. VOC Content:

1) Minimum E Range of E2.

2) Meets or exceeds LEED requirements for VOC content.

b. Environmental Performance Rating (EPR): Minimum EPR 2.

D. Wood-Knot Sealer: White shellac or other sealer recommended in writing by manufacturer for this purpose.

2.4 METAL PRIMERS

Coordinate products retained in this Article with substrates and coating systems retained in Part 3.

A. Inorganic Zinc Primer: MPI #19.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Inorganic Zinc Primer, M01/M02.

b. BLP Mobile Paint Manufacturing Company, Inc.; Mo-Zinc #3, 28-DH-50.

c. Cloverdale Paint; ClovaZinc 2, 83002.

d. Columbia Paint & Coatings; DuPont, Ganicin Inorganic Zinc-Rich Coating, 347-Y-931.

e. Dunn-Edwards Corporation; Interzinc 22, QHA 028/1/A.

f. Frazee Paint; Ameron, D9HS.

g. General Paint; Ameron, Dimetcoate 9 - Inorganic Zinc Rich, 96 Line.

h. Griggs Paint; MIL-P-38336 Inorganic Zinc Primer, 200A46.

i. ICI Paints; Devoe Coatings, Catha-Cote 304, 304.

j. Miller Paint; PPG Metalhide Inorganic Zinc Rich, 97-676.

k. Mills Paint; Interzinc 22, QHA 027/028.

l. PARA Paints; Insl-x Checkrust Inorganic Zinc-Rich Primer, ZR-3650.

m. Parker Paint Mfg. Co. Inc.; Ameron, Dimetcoat 9 Inorganic Zinc Rich.

n. PPG Architectural Finishes, Inc.; Metalhide One-Pac, Inorganic Zinc Rich Primer, 97-676.

o. Rodda Paint Co.; Carboline, Carbozinc 11.

p. Sherwin-Williams Company (The); Industrial & Marine, Zinc Clad II Ethyl Silicate, B69V3/D11.

q. Sigma Coatings; Sigma Silguard SC, 7550.

r. Spectra-Tone; Insl-x Check Rust Inorganic Zinc Rich Primer, ZR-3650.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

B. Epoxy Zinc Primer: MPI #20.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Cloverdale Paint; ClovaZinc 3, 83003.

b. Columbia Paint & Coatings; Carboline, Carboline 861, 861.

c. Coronado Paint; Polyamide Epoxy Zinc Rich Primer, 101-152.

d. Dunn-Edwards Corporation; Interzinc 52, EPA 175.

e. Frazee Paint; Ameron, 68HS.

f. General Paint; Ameron, 68 H.S. - Epoxy Zinc Rich Coating, 96 Line.

g. Griggs Paint; Epoxy Zinc Rich Primer, 600A75.

h. ICI Paints; Devoe Coatings, Catha-Cote, 313.

i. Miller Paint; PPG Aquapon Zinc Rich Primer, 97-670.

j. Parker Paint Mfg. Co. Inc.; Ameron, Amercoat Zinc Rich Epoxy Primer, 68HS.

k. Porter Paints; Porterzinc 3000, Zinc Rich Epoxy Primer, 3000.

l. PPG Architectural Finishes, Inc.; Aquapon Epoxy Zinc Rich Primer, 97-670.

m. Sherwin-Williams Company (The); Industrial & Marine, Zinc Clad IV, B69A8/V8.

n. Sico, Inc.; Rust-Oleum, Zinc-Sele, 9334.

o. Sigma Coatings; Sigmarite Zinc Primer, 7401.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

C. Rust-Inhibitive Primer (Water Based): MPI #107.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Acrylic Metal Primer, M04.

b. Bennette Paint Mfg. Co., Inc.; Rust Inhibitive Primer (WB), 32-107.

c. BLP Mobile Paint Manufacturing Company, Inc.; H2O RUS-KIL, Rust Resistant Primer, 310-6 /8 /9.

d. California Paints; H. P. Industrial, Rust-Stop Latex Metal Primer, 106XX-Series.

e. Cloverdale Paint; EcoLogic Rustex Primer, 703 Series.

f. Color Wheel Paints & Coatings; Aquatec, Industrial Acrylic Primer, 1636.

g. Columbia Paint & Coatings; Professional, Metal Prime, 05-255-PP.

h. Coronado Paint; H.P. Acrylic Rust Inhibitive, 180-11/147.

i. Diamond Vogel Paints; V-Code 200, Acrylic Maintenance Primer/Finish, MC-Series.

j. Dunn-Edwards Corporation; Intercryl 520, 52010.

k. Duron Inc.; Dura Clad Universal Acrylic Metal P, 33-105.

l. Frazee Paint; Acrylic Metal Primer, 561.

m. General Paint; Envirogard, Waterborne Self-Prime Coating, 15-002.

n. Griggs Paint; Waterbase Acrylic Primer, 700R05.

o. Hallman Lindsay Quality Paints; Metalguard, DTM Acrylic Metal Primer, 338-R.

p. ICI Paints; Devoe Fuller, Mirolac-WB, DP85XX or Devoe Coatings, Devflex TDM Flat Int/Ext W.B. Primer, 4020.

q. Insl-x; Check Rust, Water Reducible H.P. Primer, WRP800.

r. Kelly-Moore Paints; DTM Acrylic Metal Primer, 5725.

s. Miller Paint; PPG Pitt-Tech, Rust Inhibitive Primer (WB), 90-712 or Acrimetal Primer-Finish White, 5000.

t. Northern Paint; Colorlox Industrial, Acrylic DTM Primer, Red Oxide/Grey, 601-10/20.

u. PARA Paints; Insl-x, WB High Performance Primer, WRP-800.

v. Parker Paint Mfg. Co. Inc.; Rustoleum, Speedy Dry DTM, Red/Grey, 3169/3181.

w. PPG Architectural Finishes, Inc.; Porter Coatings, DTM Acrylic Primer/Finish, 215 or Pitt-Tech, Rust Inhibitive Primer (W.B.), 90-712.

x. Rodda Paint Co.; Professional Maintenance, Metal Master Primer, 508901X.

y. Sherwin-Williams Company (The); DTM Acrylic Primer/Finish, B66W1.

z. Sico, Inc.; Rust-Oleum, Speedy Dry DTM, Red/Grey, 3169/3181.

aa. Sigma Coatings; Sigma Rustgone Primer, 5607.

ab. Spectra-Tone; Industron, Acrylic Rust Inhibiting Metal Primer, 081.

If retaining requirements for environmental characteristics below, coordinate with products retained above.

3. Environmental Characteristics:

a. VOC Content:

1) Minimum E Range of E2.

2) Meets or exceeds LEED requirements for VOC content.

b. Environmental Performance Rating (EPR): Minimum EPR 2.

D. Cold-Curing Epoxy Primer: MPI #101.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Ameron International; Amercoat Multi Purpose Epoxy, 385PA.

b. Coronado Paint; Polyamide Epoxy Primer, 1201-147.

c. ICI Paints; Devoe/Fuller, Surface Tolerant Epoxy, DP32U-XX or Bar-Rust 235, Multi-Purpose Epoxy Coating, DC235K3501.

d. Sherwin-Williams Company (The); Industrial & Marine, Duraplate 235 Multi-Purpose Epoxy, B67W235.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E1.

E. Alkyd Anticorrosive Metal Primer: MPI #79.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Industrial, Alkyd Metal Primer, M06 or IronClad, Alkyd Low Lustre Metal & Wood Enamel, C163.

b. Bennette Paint Mfg. Co., Inc.; Alkyd Anti-Corrosive Metal Primer, 32-79.

c. Cloverdale Paint; Rustex Metal Primer, 71024/29/34.

d. Columbia Paint & Coatings; Hi-Performance Coatings, Red Oxide Zinc Phosphate Primer, 04-022-PP.

e. Coronado Paint; Rust Scat, Alkyd Metal Primer, 35-111.

f. Frazee Paint; Metal Prime, Interior Exterior Alkyd Primer, 661.

g. General Paint; Anti-Corrosive Marine Primer - Red, 63-212.

h. ICI Paints; Devoe Coatings, Devguard T & S Primer, 4160.

i. Insl-x; AllPro, Pro Universal Red Oxide Primer, AP4300-12354 or Check Rust Universal Primer, MP-9015.

j. Kelly-Moore Paints; Kel-Guard, Alkyd Rust Inhibitive Primer, 1710-120.

k. Kwal-Howells Paint; Accu-Pro, Interior/Exterior White Metal Primer, 9210.

l. Rodda Paint Co.; Barrier III HS, High Solids Rust Inhibitive Metal Primer, 70 8295 X.

m. Sherwin-Williams Company (The); Industrial & Marine, Kem Kromic Universal Metal Primer, B50WZ1.

n. Spectra-Tone; Insl-x, Check Rust Universal Primer, MP-9015.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

F. Quick-Dry Alkyd Metal Primer: MPI #76.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Rapid Dry Metal Primer, CM05-70.

b. BLP Mobile Paint Manufacturing Company, Inc.; Quick Dry Primer Red/Gray/White, 521-10/8/5.

c. California Paints; H. P. Industrial, Prime Line Metal Primer - Gray, Red, 170X.

d. Cloverdale Paint; Quick Dry Shop Primer, 71134.

e. Color Wheel Paints & Coatings; Contractor's Choice, Ironize Inhibitive Primer, 640.

f. Columbia Paint & Coatings; Industrial, Lead-Free Gray Primer/Speedset HB, 07-426/473.

g. Coronado Paint; Quick Dry Alkyd Metal Primer, 895 Line.

h. Diamond Vogel Paints; V-Tech 600, Fast Dry Universal Alkyd Primer, LU-0500/5500.

i. Dunn-Edwards Corporation; Interlac 260, 26097.

j. Duron Inc.; Dura Clad Fast Dry Universal Primer, 33-042.

k. Frazee Paint; Metal Prime, 661.

l. General Paint; Q. D. Anti-Corrosive Primer Red/Gray, 06-154/160.

m. Griggs Paint; Jet-Dri Metal Primer - Gray, 200A26.

n. Hallman Lindsay Quality Paints; Metalguard, Q. D. Alkyd Rust Inhibitive Primer, 330.

o. ICI Paints; Devoe/Fuller, Primatite, DP271XX, Devoe Coatings, Devguard 4142, 4142, Devoe Coatings, Rustguard QD Shop Coat Primer, 4140, or Devoe Coatings, Devguard T & S Primer, 4160.

p. Insl-x; AllPro, Pro Universal Primer - White, AP4300-12354 or Check Rust Speedy Metal Primer, MP0911/0915.

q. Miller Paint; PPG Alkyd Fast Dry Enamel Primer, FSC16015 or Metal Primer Quick Dry Red Oxide, 364.

r. Mills Paint; Superior Quality, F/D Anti-Corrosive Primer-Red/Gray, 548/543.

s. Northern Paint; Colorlox Industrial, Fast Dry Red Oxide Primer, 601-84.

t. Parker Paint Mfg. Co. Inc.; Overlay Red Primer, 1679.

u. Porter Paints; U-Prime, Fast Dry Universal Primer, 286.

v. PPG Architectural Finishes, Inc.; Multiprime, Fast Dry 2.8 VOC, 94-258/269 or Alkyd Q.D. Enamel Primer Red Oxide, FSC16015.

w. Rodda Paint Co.; Professional Maintenance, Barrier 111 H S, 708295X.

x. Spectra-Tone; Zap-It, Metal Grip Primer, 215.

y. Tower Paint; Industrial Metal Primer, 7130.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

G. Cementitious Galvanized-Metal Primer: MPI #26.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Cloverdale Paint; Cementitious Galvanized Metal Primer, 15930.

b. Dunn-Edwards Corporation; Galv-Alum, QD43-7.

c. General Paint; Cementitious Self-Prime Coating, 06-020.

d. Griggs Paint; Galvanized Metal Primer, 200W45.

e. ICI Paints (Canada); GliddenUltra, Cementitious Primer, 8000.

f. Miller Paint; PPG Speedhide Galvanized Metal Primer, 6-209.

g. PPG Architectural Finishes, Inc.; Speedhide, Cementitious Galvanized Metal Primer, 6-209 or Porter Coatings, Galvanized Metal Primer, 290.

h. Sherwin-Williams Company (The); Industrial & Marine, Opti-Bond Multi-Surface Coating, B50W100.

i. Tower Paint; Dry Fog Alkyd Galvanized Primer, 375935.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

H. Waterborne Galvanized-Metal Primer: MPI #134.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Acrylic Metal Primer, M04.

b. Bennette Paint Mfg. Co., Inc.; Waterborne Galvanized Primer, 32-134.

c. BLP Mobile Paint Manufacturing Company, Inc.; H2O RUS-KIL, Acrylic DTM -White/Gray/Red, 310-6/ 8/ 9.

d. California Paints; H. P. Industrial, Rust-Stop Latex Metal Primer, 106X-Series.

e. Cloverdale Paint; EcoLogic Rustex Primer, 700 Series.

f. Color Wheel Paints & Coatings; Aquatec, Industrial Acrylic Primer, 1636.

g. Columbia Paint & Coatings; Hi-Performance, Waterborne Acrylic Bonding Primer, 05-174-PP or Professional, Metal Prime, 05-255-PP.

h. Coronado Paint; H. P. Acrylic Rust Inhibiting Primer, 180-11/147.

i. Diamond Vogel Paints; V-Code 200, Acrylic Maintenance Primer Finish, MC-Series.

j. Dunn-Edwards Corporation; M-P Prime, W713.

k. Duron Inc.; Dura Clad, Acrylic Galvanized Metal Primer, 33-100.

l. Farrell-Calhoun; 100% Acrylic Ext. Latex Undercoat, 235.

m. Frazee Paint; Acrylic Metal Primer, 561.

n. General Paint; Galvanized Primer, 51-050.

o. Griggs Paint; DC701 Acrylic Waterborne Primer, 701A06.

p. Hallman Lindsay Quality Paints; Metalguard, DTM Acrylic Metal Primer, 338-R.

q. ICI Paints; Devoe Coatings, Devflex WB DTM Primer Finish, 4020.

r. Insl-x; Check Rust, Water Reducible Primer, WRP800 Series.

s. Iowa Paint Manufacturing Company, Inc.; Meta Cryl, Galvanized Primer, 1069.

t. Kelly-Moore Paints; Kel-Guard, Galvanized Iron Primer, 1722.

u. M.A.B. Paints; HydroPrime, 073-189.

v. Miller Paint; PPG Pitt-Tech, DTM High Performance Primer/Finish, 90-712 Series or Acrimetal Primer-Finish White, 5000.

w. Mills Paint; Superior Quality, Gripper Plastex Primer, P150.

x. Northern Paint; Colorlox, Prime Magic Latex Primer, 30-55.

y. PARA Paints; Waterborne Galvanized Primer, 750.

z. Parker Paint Mfg. Co. Inc.; Galv-O-Prime, Galvanized Iron Primer, 1821.

aa. Porter Paints; Porter Guard, DTM Acrylic Primer/Finish, 215.

ab. PPG Architectural Finishes, Inc.; Pitt-Tech, DTM High Performance Primer/Finish, 90-712 or Porter Coatings, DTM Acrylic Primer/Finish, 215.

ac. Rodda Paint Co.; Professional Maintenance, Metal Master Primer, 508901X.

ad. Sherwin-Williams Company (The); Industrial & Marine, DTM Acrylic Primer/Finish, B66W1.

ae. Sico, Inc.; Corrostop, Galvanized Primer, 270-660.

af. Spectra-Tone; Sigmetal Primer ZP, 7143.

If retaining requirements for environmental characteristics below, coordinate with products retained above.

3. Environmental Characteristics:

a. VOC Content:

1) Minimum E Range of E2.

2) Meets or exceeds LEED requirements for VOC content.

b. Environmental Performance Rating (EPR): Minimum EPR 2.

I. Quick-Drying Primer for Aluminum: MPI #95.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Rapid Dry Metal Primer, CM05.

b. California Paints; H. P. Industrial, Prime Line Metal Primer - Grey, 1704.

c. Cloverdale Paint; Quick Dry Non-Lifting Metal Primer, 71312.

d. Color Wheel Paints & Coatings; Contractor's Choice, Ironize Inhibitive Primer, 640.

e. Columbia Paint & Coatings; Industrial, Universal Low VOC Phenolic Primer, 07-576-PP, Lead-Free Primer - Red, 07-437-PP, or Lead Free Primer - Gray, 07-426-PP.

f. Coronado Paint; Quick Dry Alkyd Metal Primer, 895 Line.

g. Frazee Paint; Metal Prime, 661.

h. General Paint; Q.D. Anti Corrosive Primer Red/Grey, 06-154/160.

i. Griggs Paint; Deer Valley QD Grey Primer, 200A04.

j. ICI Paints; Devoe Coatings, Devguard T & S Primer, 4160, Devoe/Fuller, Surmax, DP27915/17, or Devoe Coatings, Rustguard QD Shop Coat Primer, 4160.

k. Miller Paint; Aluminum & Ferrous Metal Primer, 484 or PPG Zinc Chromate Primer, 6-204.

l. Mills Paint; Superior Quality, Fast Dry White Barrier Primer, 551.

m. Northern Paint; Colorlox, Fast Dry Gray Primer, 601-58.

n. PARA Paints; Insl-x Speedy Metal Primer, MP-915.

o. Parker Paint Mfg. Co. Inc.; Overlay Red Primer, 1679.

p. Porter Paints; U-Prime, Fast Dry Universal Primer, 286.

q. PPG Architectural Finishes, Inc.; Speedhide, Quick Dry Metal Primer, 6-204.

r. Rodda Paint Co.; Professional Maintenance, Barrier III HS, 708295X.

s. Sico, Inc.; Rust-Oleum, Speedy Dry, 1573.

t. Spectra-Tone; Insl-x Speedy Metal Primer, MP-915.

u. Tower Paint; Red Oxide Metal Primer, T110.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

J. Vinyl Wash Primer: MPI #80.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. BLP Mobile Paint Manufacturing Company, Inc.; Vinyl Wash Primer, 9-42.

b. Cloverdale Paint; EtchPrime 50, 83050.

c. Columbia Paint & Coatings; Insl-x Vinyl Wash Primer, WCP-100.

d. Coronado Paint; Vinyl Wash Metal Primer, 316-200.

e. Diamond Vogel Paints; Vinyl Wash Primer, LE-6222.

f. Griggs Paint; Metal Pretreatment Wash Primer, 200G05.

g. ICI Devoe, Devguard 27301, 27301/02.

h. Insl-x; Vinyl Wash Primer, WCP100.

i. Miller Paint; PPG Polyclutch Wash Primer, 97-686 Series or Vinyl Wash Coat Primer, 9172.

j. Northern Paint; Guerton Bros., Vinyl Wash Primer, 8320181/82.

k. PARA Paints; Insl-x Vinyl Wash Primer, WCP-100.

l. Parker Paint Mfg. Co. Inc.; Farwest Chemicals, Pre-Treatment Wash Primer, DOD P 15328.

m. PPG Architectural Finishes, Inc.; Polyclutch, Vinyl Wash Primer, 97-687/688.

n. Rodda Paint Co.; Professional Maintenance, Vinyl Wash Coat, 709700X.

o. Sherwin-Williams Company (The); Industrial & Marine, Industrial Wash Primer, P60G2/R7K44.

p. Sico, Inc.; Sicovinyl, 360-535.

q. Sigma Coatings; Sigma Etch Primer, 7180.

r. Spectra-Tone; Insl-x Vinyl Wash Primer, WCP-100.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E3.

2.5 WATER-BASED, LIGHT-INDUSTRIAL COATINGS

A. Gloss, Water-Based, Light-Industrial Coating: MPI #110-G6.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Cloverdale Paint; EcoLogic W.B. Architectural Finish, 70603.

b. Columbia Paint & Coatings; High Performance, Acry-Shield Gloss Enamel, 05-260.

c. Coronado Paint; DTM Acrylic Coatings, 180 Line.

d. Dunn-Edwards Corporation; Permagloss, Interior and Exterior 100% Acrylic G, W 960.

e. General Paint, Envirogard; Waterborne Acrylic Gloss 15-010.

f. Insl-x; AllPro, Pro DTM Gloss Latex, AP4300-12181 or Armor-Grip, DTM Acrylic Enamel, DM-7410.

g. Kelly-Moore Paints; DTM Acrylic Gloss Enamel, 5780.

h. PPG Architectural Finishes, Inc.; Pitt-Tech, High Performance Acrylic, 90-374.

i. Sherwin-Williams Company (The); Industrial & Marine, Sher-Cryl HPA Gloss, B66W311.

j. Spectra-Tone; Insl-x Armor Grip, DTM Acrylic, DM-7410.

k. Vista Paint; Industrial Waterborne Semi-Gloss, AP12.

If retaining requirements for environmental characteristics below, coordinate with products retained above.

3. Environmental Characteristics:

a. VOC Content: Minimum E Range of E2.

b. Environmental Performance Rating (EPR): Minimum EPR 2.

B. Semigloss, Water-Based, Light-Industrial Coating: MPI #110-G5.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; (Canada), Latex, M28-08.

b. Bennette Paint Mfg. Co., Inc.; Int/Ext Hi Performance Semi-Gloss, 32-110-2.

c. Cloverdale Paint; EcoLogic W.B. Architectural Finish, 70623.

d. Columbia Paint & Coatings; High Performance, Acry-Shield Semi-Gloss Enamel, 05-262.

e. Coronado Paint; DTM Acrylic Coatings, 182 Line.

f. Dunn-Edwards Corporation; Permasheen, Int./Ext.100% Acrylic Semi-Gloss, W 901.

g. Farrell-Calhoun; Tuff-Boy, Waterborne DTM Enamel, 8000.

h. General Paint, Envirogard; Waterborne Acrylic Semi-Gloss, 15-020.

i. ICI Paints; Devoe/Fuller, Mirrolac-WB, DP 84-XX, Devoe Coatings, Devflex WB Acrylic SG Enamel, 4206-0100, or Paints; Devoe Coatings, Devflex WB Acrylic SG Enamel, 4216.

j. Insl-x; Armor-Grip, DTM Acrylic Enamel, DM-7409.

k. Miller Paint; AcriMetal DTM Lite Semi-Gloss, 5200.

l. Mills Paint; Enviro-Lac Legacy, Acrylic Waterborne Coatings, 2500 Series.

m. Sherwin-Williams Company (The); Industrial & Marine, Sher-Cryl HPA Semi-Gloss, B66W351.

n. Vista Paint; Premogloss, 7900.

If retaining requirements for environmental characteristics below, coordinate with products retained above.

3. Environmental Characteristics:

a. VOC Content:

1) Minimum E Range of E3.

2) Meets or exceeds LEED requirements for VOC content.

b. Environmental Performance Rating (EPR): Minimum EPR 2.

C. Eggshell, Water-Based, Light-Industrial Coating: MPI #110-G3.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Cloverdale Paint; EcoLogic W.B. Architectural Finish, 70653.

b. Columbia Paint & Coatings; High Performance, Acry-Shield Eggshell Enamel, 05-265.

c. Dunn-Edwards Corporation; Permashell, Interior and Exterior 100% Acrylic E, W 940.

d. Envirocoat Technologies Inc.; Envirocoatings, Envirocoat, Ceramic Insulcoat – Interior or Liquid Ceramic, Liquid Ceramic Interior Wall Coat, EC 1040-1.

e. Frazee Paint; Mirro-Glide Eggshell, 126.

f. General Paint, Envirogard; Waterborne Acrylic Eggshell, 15-030.

g. ICI Paints; Devoe Coatings, Devflex 4210.

h. Mills Paint; Enviro-Lac Legacy, Acrylic Waterborne Coatings, 2400.

i. Porter Paints; Porter Guard, DTM Acrylic Satin Enamel, 2805.

If retaining requirements for environmental characteristics below, coordinate with products retained above.

3. Environmental Characteristics:

a. VOC Content:

1) Minimum E Range of E2.

2) Meets or exceeds LEED requirements for VOC content.

b. Environmental Performance Rating (EPR): Minimum EPR 2.

2.6 EPOXY COATINGS

A. Epoxy, Cold-Cured, Gloss: MPI #77.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Polyamide Epoxy Coating, M36/M37.

b. California Paints; H. P. Industrial, Tile-Cote Polyamide-Epoxy Coating, 12XX/1200.

c. Cloverdale Paint; ClovaCoat 300, 833.

d. Columbia Paint & Coatings; Insl-x, Insl-Tile II, EP-5300.

e. Coronado Paint; Polyamide Epoxy Coating, 101 Line.

f. Frazee Paint; Ameron, 72HS.

g. ICI Paints; Devoe/Fuller, Guardcote, DP34UXX.

h. Insl-x; Insl-Tile II; Activated Epoxy, EP5300.

i. Miller Paint; PPG Aquapon, Epoxy Cold Cured - Gloss, 95-1.

j. Mills Paint; Superior Quality, 2 Component Epoxy, 800.

k. Northern Paint; Phillips, Herculon Epoxy, 83640.

l. Porter Paints; Porterglaze 4000, Gloss Epoxy, 4000.

m. PPG Architectural Finishes, Inc.; Aquapon, Epoxy Cold Cured Gloss, 95-1.

n. Sico, Inc.; Rust-Oleum, H.P. Epoxy, 9100/9101.

o. Sigma Coatings; Sigma Cover TCP, 7476.

p. Spectra-Tone; Insl-x, Insl-Tile II, EP5300 Series.

q. Tower Paint; Epoxy High Gloss Enamel, T8700.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

B. Water-Based Epoxy (Interior and Exterior): MPI #115.

See Editing Instruction No. 1 in the Evaluations for cautions about naming manufacturers and products. Retain one of two subparagraphs and list of manufacturers and products below. See Division 1 Section "Product Requirements."

See the current "MPI Approved Products List" at www.paintinfo.com. MPI updates this list frequently.

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

2. Products: Subject to compliance with requirements, provide one of the following:

a. Benjamin Moore & Co.; Acrylic Epoxy Gloss "A", Hardener "B", M43/M44.

b. BLP Mobile Paint Manufacturing Company, Inc.; Mo-PoxY H2O-200; Waterborne Epoxy -White, 69-AW-6.

c. California Paints; H. P. Industrial, Tuf-Flex Acrylic Epoxy Water Base En, 13XX-Series.

d. Cloverdale Paint; EcoLogic Water-Borne Epoxy, 705 Series.

e. Color Wheel Paints & Coatings; Contractor's Choice, Clean-Coat Aqua Epoxy, 1300.

f. Columbia Paint & Coatings; Dupont, Corlar Waterborne Acrylic Epoxy, 76P or Insl-x, Aqua-Tile, AT-A100 Line.

g. Coronado Paint; Water-Based Amine Adduct Epoxy, 142 Line.

h. Diamond Vogel Paints; Aqua Pox, Waterborne Epoxy, MC-1245/6.

i. Dunn-Edwards Corporation; Intergard 735, 73510.

j. Farrell-Calhoun; Tuff-Boy, Waterborne Epoxy, 1200 WB.

k. Frazee Paint; Epox-Z-Cote Gloss, 547.

l. General Paint, Ameron; Amercoat 335, 96 Line.

m. Griggs Paint; Hydropox #2 Waterborne Epoxy Coating, 600V03.

n. ICI Paints; Devoe/Fuller, Gardcote-WB, DP25U9XX, Devoe Coatings, Tru Glaze WB Epoxy Gloss Coating, 4408, or Devoe Coatings, Tru Glaze WB Epoxy Coating, 4418.

o. Insl-x; AllPro, Pro Water Based Epoxy, AP4300-12231 or Aquatile, Water Base Epoxy, ATA100 Line.

p. Iowa Paint Manufacturing Company, Inc.; W. B. Acrylic Epoxy Gloss, 18939.

q. Kelly-Moore Paints; Envira-Poxy, 7100.

r. Miller Paint; Waterborne Epoxy Gloss, 4300/4440 or PPG Aquapon, Water Based Epoxy, 98-1 Series.

s. PARA Paints; Insl-x Aqua-Tile Epoxy, ATA-100.

t. Parker Paint Mfg. Co. Inc.; Ameron, Amercoat 335, 335.

u. Porter Paints; Dura-Glaze WB, Gloss Epoxy, 9371.

v. PPG Architectural Finishes, Inc.; Aquapon, Waterborne Epoxy, 98-1/98-98.

w. Rodda Paint Co.; Professional Maintenance, Aqua-Flint, 559201X.

x. Sherwin-Williams Company (The); Industrial & Marine, Water Based Catalyzed Epoxy, B70W Series.

y. Sico, Inc.; Rust-Oleum, Acrylic Epoxy, 5300 Series.

z. Spectra-Tone; Insl-x Aqua-Tile W.B. Epoxy, ATA 100 Series.

aa. Tower Paint, Sierra, Wall & Trim Enamel, S50.

If retaining requirements for VOC content below, coordinate with products retained above.

3. VOC Content: Minimum E Range of E2.

C. High-Build Epoxy Marine Coating, Low Gloss: MPI #108.

See Editing Instruction No. 1 in the Evaluations for cautions…