Appendix_H_-_Baseline_Calibration_Limit_(BCL)_Listing.docx

PRECISION MEASUREMENT EQUIPMENT LABORATORY (PMEL)

PWS

FA4890-17-R-0011

APPENDIX H – BASELINE CALIBRATION LIMIT (BCL) LISTING

1.0 Andersen BCL

2.0 Andrews BCL

3.0 Arnold BCL

4.0 Barksdale BCL

5.0 Cannon BCL

7.0 Cape Canaveral BCL

8.0 Columbus BCL

9.0 Dyess BCL

10.0 Ellsworth BCL

11.0 Elmendorf BCL

12.0 FE Warren BCL

13.0 Fairchild BCL

14.0 Feltwell BCL

15.0 MacDill BCL

16.0 Malmstrom BCL

17.0 Maxwell BCL

18.0 McConnell BCL

19.0 Minot BCL

20.0 Moody BCL

21.0 Offutt BCL

22.0 Patrick BCL

23.0 Peterson BCL

24.0 Scott BCL

25.0 Sheppard BCL

26.0 Tyndall BCL

27.0 Vance BCL

28.0 Vandenberg BCL

29.0 Whiteman BCL

30.0 Wright-Patterson BCL

PMEL PWS

H – 1 Baseline Calibration Listing_Andersen.xlsx K1

K1 SECTION (ITEMS IN RED HAVE BEEN CHANGED OR ADDED)

TOD = Technical Order Directed CON COV = Contractor Conveniance LOS = Limitation of Standards TEMP = Temporary (One Time Only

P/N NOMENCLATURE ID# LIMITATION

16345A CALIBRATION BOX A220744 Unit designated CBU. drj 5/5/08

3100A-4006 POWER SUPPLY A220978 MONITOR ALL OUTPUTS SOURCE ONLY

WGMC8-40 432BOPT009 PWR MTR 2EA A221011 NOISE NOT CAL'D. USE ONLY WITH 10' CABLE. P/O WGMC8-40 CBU

WGMC8-40 432BOPT009 PWR MTR 2EA A221012 NOISE NOT CAL'D. USE ONLY WITH 10' CABLE. P/O WGMC8-40 CBU

3400A VOLTMETER RMS SSA H60-3400A A221292 NOT CAL'D BELOW 50 HZ 1mv Range not Cal'd (CBU). Not on File 16Aug13

845AR NULL DETECTOR A222902 1uV AND 3uV RANGES NOT CAL'D 1uV Range not Cal'd. NPC 16Aug13

9 SING-MULTI RANGE DC METERS A222990 50 AMP RANGE NOT CAL'D (PREVIOUS); CBU

260-6XLPM VOM SSA260-6XLP A222994 INDICATION ONLY. DO NOT USE FOR QUANTITATIVE MEASUREMENTS; NPC

415B PWR SUPPLY A223020 MONITOR ALL OUTPUTS; LABEL REACCOMPLISHED 95129 (NPC)

TS-183-B/U Battery Tester A223040 CBU

6205B DUAL POWER SUPPLY SSA 6205C A223075 MONITOR ALL OUTPUTS (NPC)

77AN MULTIMETER A223198 10 AMP RANGE NOT CAL'D Not limited 16Aug13

77AN MULTIMETER A223266 Not Cal'd Above 1.9 M Ohms NPC

152-90-9904 CU Substitution Box A495293 25 CU = 25.25 CU. 300 CU = 298.5 CU. TO Directed CBU

80E VOLTAGE DIVIDER A794014 TO Directed. Accuracy +/- 0.025% up to rated voltage; Front panel meter not certified; Use with a differential voltmeter; Model 80E-10 SN 264 12/17/08 jlp TOD accuracy ±0.025% of Reading up to 10kVdc. Front Panel Meter not cal'd 16Aug13

801C Generator/Detector B112008 1 uV Range Not Calibrated

80E VOLTAGE DIVIDER C451963 T.O. DIRECTED ACCURACY +/- .025%; FRONT PANEL METER INOPERATIVE S/N 00852 FRONT PANEL METER REPAIRED Accy: ±0.2% (TOD) 16Aug13

80K-40 HIGH VOLTAGE PROBE E182882 ACCURACY +/- .2% (TO DIRECTED) DC ONLY * +/- 1%, 20 to 35 KVDC at 20 to 30 degrees C add 1% at 10 degrees C to < 20 & > 30 to 45 degrees C; +/- 2%, 0 to < 20 & > 35 to 40 KVDC. DC Cal'd Only. Use w/10 Mohm Input Voltmeter

80F-15 VOLTAGE DIVIDER F041357 DCV CAL'D ONLY. CAL'D TO +/- .4%; CBU Not on file 16Aug13

EL750 ELECTRONIC LOAD J287421 10 AMP RANGE NOT CAL'D. VOLTS KNOB FUNTIONAL BUT NOT CAL'D (T.O. DIRECTED)

E3634A Power Supply DC J287495 Monitor all outputs. NPC 8/25/08

GPC-3030D Power supply J287862 Monitor all Outputs NPC 9/4/08

AP BCL-01 Rev. .01

K2

K2 SECTION (ITEMS IN RED HAVE BEEN CHANGED OR ADDED)

TOD = Technical Order Directed CON COV = Contractor Conveniance LOS = Limitation of Standards TEMP = Temporary (One Time Only

P/N NOMENCLATURE ID# LIMITATION

240C POWER RESISTOR A222943 Monitor All Outputs (NPC)

AP BCL-01 Rev. .01

K3

K3 SECTION (ITEMS IN RED HAVE BEEN CHANGED OR ADDED)

TOD = Technical Order Directed CON COV = Contractor Conveniance LOS = Limitation of Standards TEMP = Temporary (One Time Only

P/N NOMENCLATURE ID# LIMITATION

527E Frequency Difference Meter A222103 Range 10 parts to 11th cannot be verified due to excessive noise (TO Directed) NPC

8662AOPT043W55 SYNTHESIZED SIGNAL GENERATOR A222142 Incident AM, SSB Ph Noise, SSB Broadband Noise Floor, Spect Purity Non-Harmonics Not Cal'd (Previous) Abs Ampl not cal'd below -100dBm 640 MHz output not cal'd (T.O. Dir) CBU

8660COPT001-003 SIG GEN A222810 CBU

652A T/OSCILLATOR A222815 Freq cald to +/- 3.5% expand mode ref @ 1Khz Atten cald to +/- .5db below -30db Attenuator accuracy at -40 dB +/- 0.081 and -50 dB +/- 0.091 TOD / CBU

8640BOPT003 SIG GEN A222821 Freq, output level, attenuation and internal ref cald ONLY. output attenuator not cald below -120dbm (PREVIOUS) Frequency Range, Harmonics, Output Level and Attenuation, Output Level Flatness, & Internal Reference Cal'd Only. Attenuator Not Cal'd Below -120 dBm. (1 Feb 08; SJN) CBU 16 Aug 2013

ANAPM270V3 TRANSPONDER TS A222844 DETECTED VIDEO NOT CAL'D (CBU)

3312A FUNCTION GEN A222849 MONITOR ALL OUTPUTS (NPC)

240C Kelvin Ratio Bridge A222900 CBU

(20160516 KAA)

334A DISTORTION ANALYZER A223264 AM DETECTOR NOT CALIBRATED: DISTORITION MEASUREMENT OF AM RF CARRIERS WITH THE TI RF DET SELECTED. (TOD) 16Aug13

3586C SELECTIVE LEVEL METER A223981 AMPLITUDE ACCURACY 50 AND 75 OHM INPUTS CAL'D TO +/- .03db FROM 20kHz to 32.5MHz on the -80 to +20dBm Range / CBU

8566A SPECTRUM ANALYZER A241184 Not cal'd above 18GHz. Noise Side Band, Residual Response, Multiple Image&Out of band Resp, Gain Compression., Line Related Sidebands, 2nd harmonic and 3rd Order Distortion not cal'd. Freq Response cal'd up to 100kHz only. Average Noise Level </= 110dBm from 2.39 to 5.71GHz (previous). 30Dec13 Average Noise Level ≤-110 dBm from 2.0 to 5.8 GHz. Multiple, Image and Out-of-Band Responses not cald. Resolution BW Amplitude: ±0.75 dB at 30 kHz setting. (Con Con) (20161003 ECA) Second Harmonic Distortion not cald. Average Noise Level ≤-110 dBm from 2.0 to 5.8 GHz. Resolution BW Amplitude: ±0.75 dB at 30 kHz setting. Sweep time not cald above 20 seconds. Cumulative Flatness and Multiple, Image and Out-of-Band Responses not cald. (Con Con) (20170118 ECA)

68369NV OPT2B,11 SYNTHESIZED SIGNAL GENERATOR A247230 Reference Oscillator downgraded to <1X10E-6/day. (T.O. Directed) No parameters cal'd > 18GHz. Due to the frequency limitation of MMR Spectrum Analyzer, Harmonics verified up to the second harmonic (18GHz) of the 9GHz carrier frequency. Attenuator not calibrated below -90dBm at ± 1.5dB. SSB Phase Noise at 18GHz calibrated to 20GHz Specs. Nonharmonics above 2GHz calibrated to <-55dBc and Power Line and Fan Rotation Spurious Emissions calibrated to <-50dBc at all Offsets from Carrier. 06Sep13

3325A SYNTHESIZER FUNCTION GEN A482929 DC Offset NOT Calibrated. (Con Cov)

(20160806 KAA)

DC Offset NOT cald. Squarewave Output Amplitude Accuracy: ±2.0%, 1 mV to 10.0 V p-p into 50 Ω. (Con Cov) (20161116 ECA)

TDS410 DIGITIZING OSCILLOSCOPE A494930 PROBE NOT CAL'D/CBU

3048MS 8662A-003 SYNTH SIGNAL GEN A495458 SSB and Spectral Purity non-harmonic related, Incidental AM, and FM Modulation not cald. Absolute Level not cal"d below -90 dB.

(20160518 KAA)

8662AOPT003 SYNTHESIZER SIG GEN A495458 640 MHz Output Not Calibrted (TOD) SSB, Incidental AM, Spectral Purity Non-Harmonic Related Calibration, and FM Modulation Not Calibrated (Con Cov) Absolute Level Not Calibrated Below - 90 dBm (Con Cov)

Absolute Level, AM Depth, and Distortion Calibrated Using ATO 33K4-4-845-10

(20160806 KAA)

(KAA 20160512)

640 MHz output not calibrated (TOD).

SSB Phase Noise and Spectral Purity (Non-Harmonically Related) calibrated from 640 to 1279.9999998 MHz Range only. Incidental AM, Incidental FM and Incidental Φ M not calibrated. Absolute Level not calibrated below -90 dBm. (CON COV) (20170228 ECA)

640 MHz output not calibrated (TOD). SSB Phase Noise, Spectral Purity (Non-Harmonically Related), Incidental AM, Incidental FM and Incidental Φ M not calibrated. Absolute Level not calibrated below -90 dBm. (CON COV) (20170619 ECA)

3048MS 8663A-003 SYNTH SIGNAL GEN A495459 Incidental AM, Pulse modulation and BPSK not cald. Absolute level not cald below -100 dBm.

(20160518 KAA)

3585B Spectrum Analyzer A495463 Intermodulation Distortion Cal's to -75 dBc; P/O 3048MS / CBU

8447F AMPLIFIER A500382 MONITOR ALL OUTPUTS/ NPC

8662AOPT003 SYNTHESIZER SIG GEN B110827 640 MHz output Not Cal'd (T.O. Directed). Incidental AM, SSB Phase Noise, SSB Broadband Noise Floor, Spectral Purity Non-Harmonics Not Cal.d (Previous) CBU

9500B/3200 Oscilloscope Calibrator B111301 Due to lack of standards, TI SquareWave Voltage not calibrated below 5mVpp (t.O. Dir) CH1 SQUAREWAVE VOLTAGE Not Calibrated. Squarewave voltage Not cal'd above 60V P/O9500B/3200AF 22Jan14

9530 ACTIVE HEAD, 3.2 GHz B111302 EDGE PULSE(rise and fall times) Not Cal'd. P/O 9500B/3200AF

9530 ACTIVE HEAD, 3.2 GHz B111303 EDGE PULSE(rise and fall times) Not Cal'd. P/O 9500B/3200AF

9530 ACTIVE HEAD, 3.2 GHz B111304 EDGE PULSE(rise and fall times) Not Cal'd. P/O 9500B/3200AF

9530 ACTIVE HEAD, 3.2 GHz B111305 EDGE PULSE(rise and fall times) Not Cal'd. P/O 9500B/3200AF

9550 CALIBRATOR HEAD B111306 P/O 9500B/3200AF. CBU

9560 CALIBRATOR HEAD B111307 CBU

PM 1024A FEED THRU TERMINATION B111654 VSWR Only Cal'd, SWR of 1.2 from DC to 500MHz. NCR 16 Dec 2013

PM 1024A FEED THRU TERMINATION B111655 VSWR Only Cal'd, SWR of 1.2 from DC to 500MHz. NCR 16 Dec 2013

PM 3341 FEED THRU TERMINATION B111682 RANGE: DC TO 500 MHZ; VSWR <= 1.2 VSWR ONLY CAL'D AT MALE CONNECTOR END ONLY. VERIFY DC IMPEADANCE PRIOR TO USE Made NCR IAW N17 20140422 PQA

3011 Feedthru Termination B111683 VSWR ≤ 1.25, DC to 1 GHz. VSWR only cald at male connector end only. Range; DC to 1 GHz P/N 3011 S/N 111683, (20160518 KAA)

3011 Feedthru Termination B111684 VSWR cal'd at Male end only. 50 Ohms = 49.8716 Ohms. Range; DC to 1 GHz. P/N 3011 s/ 111684

(20160518 KAA)

3011 Feedthru Termination B111685 DC to 1 GHz VSWR ≤ 1.25 only cald at male connector. Range; DC to 1 GHz. P/N 3011 S/N

(20160518 KAA)

PM 3341 Feed thru Termination B111687 Range: DC to 500 MHz Accuracy VSWR<+ 1.2 vswr ONLY CAL'D AT MALE CONNECTOR END ONLY ; VERIFY DC IMPEDANCE PRIOR Made NCR IAW N17 20140422 PQA

H06-5347A MICROWAVE COUNTER/POWER METER C762710 Power Reference Output certified to +/-2% (TO Directed). Not Calibrated above 18 GHz. drj 10-28-08

SG503 SINE WAVE GEN C875454 FLATNESS +/- 2% FROM 50MHZ TO 100MHZ (T.O. DIRECTED) CAL'D WITH CABLE P/N 012-0482-00 CBU jlp 3/4/09 Absolute Amplitude Not Cal'd Flatness; 2% to 50MHsZ, 3% From 50 to 100MHZ, 5% from 100MHZ to 250MHZ Flatness +/- 2% from 50 to 100MHz. Cal'd with Cable 012-0057 Flatness Limited to +/- 2% from 50 MHz to 100 MHz Cal'd with Precision Cable P/N 012-0057-01 (T.O. Directed). CBU 16 Aug 13

SG503 SINE WAVE GEN C875454 FLATNESS CAL'D TO +/- 2% FROM 50MHZ TO 100MHZ, CAL'D WITH CABLE P/N 012-0482-00 TOD CBU 16 Aug 13

86603A Plug-in C875506 CBU - NEED TO GET LIMITATION

86633B Mod. Section AM/FM C875895 CBU - NEED TO GET LIMITATION

53132AOPT010-030-H01 Counter C968141 Ch. 1 50 Ohm Input Not Calibrated. (Input Inop researching repair options) (Con Cov)

(20160806 KAA)

TG501OPT1 TIME MARK GEN C983134 1NS, 2NS RANGES NOT CAL'D CBU 16 Aug 13

PG502 PULSE GEN 250MHZ C983144 MONITOR ALL OUTPUTS; NPC

SD24 TDR/SAMPLING HEAD C983359 TDR/TDT Functions Not Cal'd (Output Amplitude and Reflected Risetime.) Info: RT Ch 1 15.6pS, Chan 2 15.6pS P/O F4703A3

PM6654COPT9678B-9696 Programmable Counter/Timer C983849 CBU

1062.5502.11 SIGNAL GENERATOR E225109 SMY Residual AM is certified to <0.03% (TO directed). Calibrated with ID E225108. P/O CIVS

(20160516 KAA)

9610A/AF RF REFERENCE SOURCE E225428 Certified to P/N 9640A Specs in 33K3-4-3570-1 (TO Dir) Except Modulation Functions not Cal'd, Atten not cal'd less than -120 dBm and not below -87dBm for 500KHz. Cal'd with Head J288572 P/O 9610A/AF. Attenuation calibration referenced from +16dBm limited to ±.05dB from -50dB (-34dBm) to <-50dB (<-34dBm). (TOD) 16Aug13. Due to lack of standards, thee TI attenuation calibration will be limited to ±0.05 dB from -50 to 0 dB; ±0.15db fro -98 to <-50dB. P/O 9610A/AF. Cal'd with head J289385 (T.O. Dir) 11Oct13

3325A Synthesizer Function Generator F041123 DC Offset Not Calibrated. (CON COV 20160806 KAA)

284 PULSE GENERATOR F041646 CBU

(20160516 KAA)

SG503 Sine Wave generator F041656 CBU - NEED TO GET LIMITATION

SG503 SINE WAVE GEN F041656 Flatness +/- 2% from 50 to 100MHz Cal'd with cable 012-057-01 CBU jlp 3/4/09

SG504 Leveled Sine Wave Generator F041657 Cal'd with Output Head 015-0282-00, S/N 11350 (TO Directed) CBU

TDS5054B-AF Oscilloscope J287122 Probe Compensation Not Calibrated (Con Cov)

(20160806 KAA)

E4407B-H50 Spectrum Analyzer J287618 Firmware Revision: A.14.03. No Parameters cal'd above 18 GHz. Info: Timebase set to C:124 F:148. (New item added to inventory, 6 Dec 07. SJN)

Option AYZ NOT cald. Frequency Response not cald above 18 GHz. (Con Cov) 20170213 ECA

86117A DUAL ELECTRICAL CHANNEL MODULE M035662 The TI Transition Duration of the Step Response at the 30 GHz BW setting is limited to ≤12 ps, at the time of calibration, the approximated value was 6.79 ps for CH 1/3 and 6.49 ps for CH2/4 for the 30 GHz BW setting. The 50 GHz BW setting is limited to ≤ the AFPSL Transition Duration of the Step response value from the latest AFPSL Certificate of Calibration at the time of calibration, the approximated value was 4.84 ps for CH 1/3 and 3.76 ps for CH 2/4 for the 50 GHz BW setting (TOD) 20170725 ECA

9640A RF Reference Source M035574 Cald with ID M035575. 75 Ω Leveling Head not cald. Absolute Level not cald below -120 dBm. (Con Cov)

(20170110 ECA)

9640A-50 Leveling Head M035575 Cald with ID M035574. Absolute Level not cald below -120 dBm. (Con Cov)

(20170110 ECA)

FSU3 OPTK15 Analyzer M494229 Resolution Bandwidth Shape Factor NOT calibrated above 3 MHz. (One time due to error in NexGen) 20170320 ECA

SMA100A OPTB103, K25AF Generator M494230 Due to lack of standards, the TI Residual AM is not calibrated (TOD). Due to lack of standard, the Incidental Phase Modulation is not calibrated. (TOD & Con Cov)

(20170201 ECA)

K4

K4 SECTION (ITEMS IN RED HAVE BEEN CHANGED OR ADDED)

TOD = Technical Order Directed CON COV = Contractor Conveniance LOS = Limitation of Standards TEMP = Temporary (One Time Only

P/N NOMENCLATURE ID# LIMITATION

436AOPT022 POWER METER A220542 POWER REF CAL'D TO +/-2% (T.O DIRECTED) P/O 436A OPT E41 DELETED 16 Aug 2013

11583A ATTEN COAXIAL SET A220743 CAL'D 10MHZ TO 18GHZ/ CBU

AS4 ATTEN STD SET A220834 SEE AFTO FORM 249 FOR CHARTED VALUES 50-6 (6 DB) Attenuator Not Cal'd. See Cal Chart 50-6 (6dB) attn not cal'd (Prev) ±0.5dB from charted value & frequencies 16Aug13

432B POWER METER A221011 CBU

PMCS-1A 436AOPT022 POWER METER A222353 POWER REFERENCE OUT +/- 2% (TO DIRECTED)

435A POWER METER A222792 POWER REF +/-2% (T.O DIRECTED) CBU 16 Aug 2013

8901AOPT001 Modulation Analyzer A222828 CBU

8496AOPT001 ATTEN VAR A222866 CAL'D FROM 10MHZ TO 4GHZ, 110 db position not cald Not on File 2013

8340B SYNTHESIZED SWEEPER A223049 No Parameters Calibrated Above 18 GHz. Swept Frequency Not Calibrated. Output Power Not Calibred below -80 dB. (Con Cov)

(20160806 KAA)

Swept Frequency not cal d. Harmonics at 6.9 & 7 GHz verified up to 3rd Harmonic. Harmonics not verified above 2nd Harmonic at 10 GHz & 13.25 GHz. Non-Harmonically related Spurious Signals not verified above 26.5 GHz (CON COV) 20170626 ECA

8496BOPT001 ATTEN VAR A223137 0-100 db steps cald only

3004-10 DIR COUPLER COAX A223144 DIRECTIVITY >15DB / CBU

798C DIR COUPLER A223145 SEE CHART S/N 07457; CBU

P752D DIR COUPLER A223162 DIRECTIVITY > 30db (CBU)

P752C DIR COUPLER A223164 COUPLING VARIATION +/- .7db (CBU)

8482A PWR SENSOR A223338 SEE CAL CHART S/N 2349A10043 P/O 436A OPT E41; CBU

3551 FIX ATTENUATOR SET A223911 3 dB +/- .3dB, DC to 18 GHz; 6dB Attenuator Removed, 10 dB +/- .5 dB DC to 18 GHz; 20 dB +/- 1dB DC to 18GHz

11691DOPT001 DIR COUPLER A223996 CBU

8494OOPT001 0-11 dB Step Attenuator A284885 Unit Designated NPC, Measure Attenuation Prior to Use drj 7/19/08 NPC 16 Aug 2013

478A H73 THERMISTOR MOUNT A352628 See AFPSL Certificate of Calibration Report No. 062980005; Cal'd from 10 to 1090 MHz; Model 478A-H73 S/N 70042. Replaced 6-11-08 drj

478A-3 ZIFOR III A365664 See AFPSL Cert of Cal. Report (TO Directed Limitation). Range: 0 to 359.99° Uncertainty ±0.09°S/N 283 Model 478A3 16Aug13

478A-3 ZIFOR III A493232 See AFPSL Cert of Cal. Report (TO Directed Limitation). Range: 0 to 359.99° Uncertainty ±0.09° S/N 440 Model 478A3 20150413 QAT

11792AH15 SENSOR A495317 REFERENCED TO 3.5 TO N-TYPE ADAPTER, S/N 2407A00683, CAL'D < 18GHZ, SEE CHART , P/O 8902MS N Type Adapter married to Unit. Not Cal'd above 18 GHz. See Cal Chart. P/O 8902MS CBU 16 Aug 2016

478A H63 THERMISTOR MOUNT A495336 SEE CHART PART NUMBER 478A863 S/N 55983; CBU

8902MS 8902AOPT030,0 MEAS RECEIVER A495475 POWER REFERENCE OUTPUT +/- 2% (TO DIRECTED) Special Cal meeting POT050 Specs.Cal"d to 8902MS (OPT H15) Specs. (T.O. Dir) P/O 88902MS CBU 16 Aug 13

Special Calibration meeting Opt 050 specifications. Calibrated to 8902MS (OPTH15) specifications. (TOD) Frequency Counter Sensitivity: 22 mV rms, 150 kHz to ≤650 MHz. Power Meter not calibrated above 1 mW range. (CON CONV) (20170327 ECA)

PMCS1B 1805A RF PWR LV CTL A495479 CAL'D FOR 1mW DC SUB POWER ONLY; LOG DRIVER NOT CAL'D P/O PMCS (PREVIOUS) DC Substituted Power Cal'd at 1 mW only. LOG Driver not Cal'd. P/O PMCS1B (Previous) 27 Nov 06

8340B SYNTHESIZED SWEEPER A499995 NOT CAL'D ABOVE 18GHZ, SWEPT FREQUENCY ACCURACY AND PHASE SSB Phase noise Not Cal'd. No Parameter Cal'd > 18 GHz. Fan Noise sidebands approx 2.8KHz from carrier <55dBc. NOISE NOT CAL'D, HARMONICS CAL'D TO 2nd HARMONIC OF 9GhZ. XTAL not cald >0db No parameter cal'd >18GHz & Swept Frequency Function not cal'd. (Prev) 16Aug13

478A-3 ZIFOR III A583364 SEE AFPSL CERTIFICATE

F1109N STANDARD THERMISTOR MOUNT A793123 See AFPSL Cal. Cert. Report# 062130117 Model F1109N(w)5184 s/n 387(w)AJ9915 Not on file 16Aug13

HPDC1 HIGH POWER DIRECTIONAL COUPLER A907285 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT # 120120076 MODEL HPDC1 S/N 1484 Not on file 16Aug13

219-3 3db Attenuator B110650 3dB +/- 0.6db 16Aug13

219-3 3db Attenuator B110651 3dB +/- 0.6db 16Aug13

588C MICROWAVE PULSE COUNTER B110875 Pulse Width Accy ±50 ns. Frequencies not Calibrated Above 18 GHz. (Con Cov)

(20160806 KAA)

8902MS 68369NVOPT16 B110970 NO PARAMETER ABOVE18 GHZ. ATTENUATOR CAL'D TO -90DBM. >=2.1 GHZ HARMONICS < 55DBC (PREVIOUS) Power Line & Fan Spurious not cal'd. P/O 8902MS No parameters cal'd above18GHz. Attenuation not cal'd below -90dBm. Power Line & Fan Spurious not cal'd. (Prev) Single Sideband Phase Noise @ 18GHz cal'd to 20GHz specs 16Aug13

No parameter calibrated above 26.5 GHz. Due to limitation on standard used, Harmonics verified up to the 3rd harmonic at 7 GHz and up to the 2nd harmonic at 10, 12.4, 13 & 13.25 GHz. Spectral Purity (Nonharmonics and Power Line & Fan Rotation), Single Sideband Phase Noise, Residual FM and Pulse Modulation (Rise and Fall Time) NOT calibrated. RF Output (Leveled Power) NOT calibrated below -80 dBm. (CON CONV) (20170414 ECA)

68369NVOPT16 SYNTHESIZED SWEEPER B110971 No Parameters Cal'd above 20 GHz. Output Power not calibrated below -100 dBm. Non Harmonics ≥ to 2.1 GHz. < -50 dBc. Harmonics 2.1 to 3.6 Ghz <-50 dBc. RF Output Powrer, Non-Harmonics, AM, FM Calibrated using ATO 33K4-4-845-10. (Con Cov)

20160806 KAA)

No parameter calibrated above 26.5 GHz. Due to limitation on standard used, Harmonic verified up to the 3rd harmonic at 7 GHz and up to the 2nd harmonic at 10, 12.4, 13 & 13.25 GHz. RF Output (Max Level Output, Flatness & below 0 dBm), Spectral Purity (Nonharmonics and Power Line & Fan Rotation), Single Sideband Phase Noise and Pulse Modulation (Rise and Fall Time) NOT calibrated. (LOS & Con Cov) 20161107 ECA

No parameter calibrated above 26.5 GHz. Due to limitation on standard used, Harmonic verified up to the 3rd harmonic at 7 GHz and up to the 2nd harmonic at 10, 12.4, 13 & 13.25 GHz. RF Output Power (Max Leveled Output, Flatness & below 0 dBm), Spurious Signals (Nonharmonics and Power Line & Fan Rotation Spurious Emissions), Single Sideband Phase Noise, Residual FM and Pulse Modulation (Rise and Fall Time) NOT calibrated. (LOS & CON CONV) 20170520 ECA

909A OPT012 Termination B111371 Cal'd to 1 GHz for VSWR < 1.06

11583C ATTEN COAXIAL SET B111414 CAL'D FROM DC TO 18 GHZ SERIAL NUMBER 90155 DC to 18 GHz. See Cal Chart in Box. Stated Accuracies are from Charted Values.

ATT-0219-10-06-NNN-02 ATTENUATOR B111615 DC TO 18GHZ, 6+/- 0.3 DB

ATT-0219-06-NNN-02 ATTENUATOR B111616 DC TO 18GHZ, 6+/- 0.3 DB Deleted 16 Aug 2013

ATT-0219-10-NNN-02 ATTENUATOR B111617 DC TO 18GHZ, 10 +/- 0.5 DB

ATT-0219-10-NNN-02 ATTENUATOR B111618 DC TO 18GHZ, 10 +/- 0.5 DB

MG3693A Signal Generator B111627 Frequency Display Resolution, 0.1Hz > 10 GHz. Phase Modulation not Cal'd. (TO Directed). Ext AM/FM opts not cal'd. Attenuation not Cal'd < -100 dB. No Parameter Cal'd > 18 GHz. SSB Phase Noise and Residual FM not Cal'd. DELETED 16 AUG 13

1025A Load B111652 VSWR not Cal'd DELETED 16 AUG 2013

1025A Load B111653 VSWR not Cal'd DELETED 16 AUG 2013

346AOPT01-SP01 Microwave Frequency Counter B111768 Not Cal'd Above 18Ghz, Power Measurement not cal'd. Frequency Range and Input Sensitivity not calibrated above 26.5 GHz and not below -27 dBm (New). Power Measurement not cald (Previous) 20141107 QAT Not on file 16Aug13

No parameter cald above 26.5 GHz. Input Sensitivity from .3 to 26.5 GHz not cald below -25 dBm (CON CONV) 20160901 ECA

Input Sensitivity from .3 to 26.5 GHz not cald below -25 dBm (CON CONV) 20170616 ECA

DLM2000 DIGITAL LIGHT METER B111853 20.200 Fc and 200/2,000 Lux ranges accy: +/- 3% of reading. 2,000 fC and 20,000 Lux range accy: +/- 5% of reading (TOD) Illuminance Range Limited to: 0.21 to 500 fc Lux not cal'd (Prev) Accuracy: ±5% of Reading (TOD) 16Aug13 Accuracy limited to ±5% rdg (TOD) ILLUMINANCE RANGE limited to 0.01 to 500fC. LUX functions not cald (CON CONV) 20170426 ECA

MG3694A Signal Generator B112120 No Parameter Cal'd > 18 GHz. Attenuator Cal'd to -100 dB. (prev) SSB Phase Noise Residual FM not Cal'd. T.O. Dir: Frequency Resolution < 10 GHz 0.1Hz, >10GHz 1Hz. P/O 8902MS No parameter calibrated above 26.5 GHz. Due to limitation on standard used, Spectral Purity (Harmonic) verified up to the 3rd harmonic at 8 GHz and up to the 2nd harmonic at 10 & 13.25 GHz. (LOS & Con Con) (20161101 ECA)

70420A OPT 001 TEST SET B112149 Phase Detector offsets calibrated from 1 Hz to 10 MHz. AM Detector offsets calibrated from 10 Hz to 10 MHz (TOD) 20161220 ECA

70427A DOWN CONVERTER G062601 Spectral Purity calibrated to 10 MHz offset. AM Noise and Spurs calibrated from 10 Hz to 10 MHz offset. AM Detector Noise Floor not calibrated. (TOD) 20160627 ECA

8664AOPT001,004,H15 SIGNAL GENERATOR B112147 SSB offsets calibrated from 10 Hz to 10 MHz only. SSB at 20 kHz offset from 257.5 to 515 MHz is certified to ≤-136 dBc/Hz; 100 kHz offset from 187.5 to 257.5 MHz is certified to ≤-142 dBc/Hz. Due to lack of Standards, TI Residual AM will not be calibrated above 1360 MHz (TOD) 20161020 ECA

SSB offsets calibrated from 10 Hz to 10 MHz only. SSB at 20 kHz offset from >257.5 to 515 MHz is certified to ≤-136 dBc/Hz; 100 kHz offset from >187.5 to 257.5 MHz is certified to ≤-142 dBc/Hz (TOD).

Due to down standard, TI Residual AM is NOT calibrated (one time). (LOS) 20170725 ECA

989C943H04 Attenuator B194998 Cald +/- 1 dB. NPC. 21 Feb 1991 NPC 16 Aug 2013

8902AOPT30 MW MEASUREMENT RECEIVER B203966 CAL'D TO 8902MS SPECS, POWER REFERENCE OUTPUT +/- 2% (TO DIRECTED) Special Calibration Meeting OPT 050 specs. P/O 8902MS no OPT 002. Para 4.3 thru 4.9 cal'd CAL'D TO 8902MS(OptH15) SPECS. Power Meter,Power Reference and Tuned RF Level Not Cal'd. P/O 8902MS. Special Calibration meeting Opt 050 specs. Calibrated to 8902MS (OPT H15) specifications (T.O. directed). 20150215 QAT CBU

8481H PWR SENSOR B204458 NOT CAL'D ABOVE 13 GHZ. SEE CAL CHART S/N 1925A04216 Not on File 16 Aug 13

8485A PWR SENSOR B204560 SEE CAL CHART, NOT CAL'D ABOVE 18GHZ, USE APC-N ADAPTER S/N 02525; S/N 2347A02525 P/O 436A OPT E41; CBU

F1116N STANDARD THERMISTOR MOUNT C455566 See AFPSL Cert of Cal. Report# 070190024 Model F1116N S/N 877 Cal'd from 0.1 to 10 MHz TO Directed drj 9/16/08 Not on file 16Aug13

50-6 Attenuator C764243 P/N 50-6. S/N R7086. NPC. 8 Jun 1993 Band 3 not cal'd above 18GHz and Band 4 not cal'd (Prev) 16Aug13

8485A PWR SENSOR C764474 NOT CAL'D ABOVE 18GHZ; P/O 436A OPT E41; S/N 2703A05023; CBU

2-10 Attenuator C764647 S/N AE5309. NPC. 24 Jul 1989

28A50-1 PRECISION TERMINATION C764781 SWR<1.02, DC TO 18GHz P/O 8902MS

18A50 PREC AIR LINE C764786 SWR LESS THAN 1.03, 1 - 18 GHz ONLY AS PER T.O.; P/O 8902MS; S/N 701021

Q8486A POWER SENSOR C764816 CBU

R8486A POWER SENSOR C764915 SEE DATA SHEET; S/N A02056; P/O 436A OPT E41; (CBU)

4226-10 COAXIAL DIRECTIONAL COUPLER C875088 Certified only at 1025, 1057, 1089, 1121, 1153 MHz.

(20160505 KAA)

4227-16 DIRECTIONAL COUPLER C875103 NOT CAL'D ABOVE 18GHZ CBU

900-G10/ACP-I STANDARD ATTENUATOR C875170 SEE AFPSL CERTIFICATE OF CALIBRATION. CALIBRATED AT 30 MHZ ONLY.9.980DB ACCURACY +/- .010DB; S/N 1166 CBU 16 Aug 2013

AN/UPM-155 8000000218-1 RADAR TEST SE C875313 P/O AN-UPM/155; CBU DELETED 16 Aug 2013

8502A(W)DETECTORS 17071 DETECTOR C875365 NOT CAL'D ABOVE 18GHZ; Calibrated for N type measurements using adapter sn 365; P/O 8502A w/detectors jlp 4/15/9 Not cal'd above 18 GH, use user supplied cal factors, se chart, calibrated only for N-Type Measurements using adapter SN 365 Not cal'd > 18GHz. Calibrated for N type measurements using adapter SN366 (Prev). PROM Frequency Correction is not valid. Use USER supplied calibration Factors See Chart of Test. 16Aug13

86603A RF Section C875506 CBU

86633B Modulation section C875895 CBU

4021 DIRECTIONAL POWER SENSOR C954006 See AFPSL CERTIFICATE OF CALIBRATION; CALIBRATED IN FORWARD POWER ONLY; P/O 4421A300; SEE SPEC'S ON BACK OF AFTO 99 TAG; S/N 7540 See AFPSL Certificate of Calibration: 071000066. Model: 4021 S/N: 7540 TO Directed Limitation: Cal'd in FWD power only. Part of 4421A300. Frequency Range: 2 to 30 MHz Power Range: 0.3 to 1000 Watts. Accuracy: +/- 3.00% of reading. Output Calibrated Only.

4022 DIRECTIONAL POWER SENSOR C954007 See AFPSL CERTIFICATE OF CALIBRATION; CALIBRATED IN FORWARD POWER ONLY; P/O 4421A300; SEE SPEC'S ON BACK OF AFTO 99 TAG; S/N 7602 See AFPSL Certificate of Calibration: 071590018. Model: 4022 S/N: 7602 TO Directed Limitation: Cal'd in FWD power only. Part of 4421A300. Frequency Range: 30 MHz to 1 GHz. Power Range: 0.3 to 1000 Watts. Accuracy: +/- 3.00% of reading. Output Calibrated Only.

28N50-2 COAXIAL TERMINATION C954312 VSWR ≤ 1.005 +[0.0033 x F(GHz)] DC to ≤4.545 GHz; ≤1.02, >4.545 to 13 GHz; ≤1.03, 13 to 17 GHz; ≤1.02, 17 to 18 GHz

28NF50-2 COAXIAL TERMINATION C954393 SWR ≤ 1.005 +[0.0033 x F(GHz)] DC to 18 GHz.

1870A POWER SPLITTER C983239 PHASE TRACKING NOT CAL'D P/N 1870A S/N 2962 No Limitations

1870A POWER SPLITTER C983242 PHASE TRACKING NOT CAL'D P/N 1870A S/N 3105

1870A POWER SPLITTER C983273 PHASE TRACKING NOT CAL'D ABOVE 12 GHZ P/N 1870A S/N 3010 Not on File 16 Aug 2013

AS-4 Attenuator Set C983274 50-6(6dB) Attenuator Not Cal'd (Previous). +/- 0.5 dB from charted value and at charted frequencies

478A H73 THERMISTOR MOUNT E204325 See AFPSL Certificate of Calibration; Cal'd from 10 to 1090 MHz - TO Directed Limitation; Model 478A-H73 S/N 73720.

9610A/AF-75 75-Ohm Leveling Head (N64) E225429 See Fluke Certificate# F16128 dtd 20070913. 9610A/AF-75, S/N 915152525. Cal'd w/9610A/AF, E225428, S/N 915152386. CBU

E4448AOPT107,110,123,215,233 Spectrum Analyzer E225741 Noise sidebands ≥ 6 MHz offset certified to ≤ - 150dBc/Hz and at ≥10 MHz offset certified to ≤ -153 dBc/Hz. Other Input Related and General Spurious Responses will be certified to 18 GHz only. Audio Distrotion is only Cal'd to 100 KHz. T.O. Dir. No parameter Cal'd above 18 GHz.

Due to lack of standards, Noise Sidebands at ≥6MHz offset certified to ≤-148 dBc/Hz and at ≥10 MHz offset certified to ≤-151 dBc/Hz. Audio Distortion is only calibrated to 100 kHz (TOD). Displayed Average Noise Level not calibrated above 26.8 GHz.

Frequency Response and Other Related and General Spurious Responses NOT calibrated above 26.5 GHz. (LOS) 20160816 ECA

N5532A-504 Sensor Module J288757 Not calibrated above 2500 MHz. (Con Cov) 20170123 ECA

N5532A-526 Sensor Module E225745 No Parameter Cal'd above 18 GHz; Use Type N Adapter S/N 5745 only; P/O MMS 30 Mar 09 jlp

N5532A-550 50 GHz Sensor Module E225746 Cal'd from 50 MHz to 50 GHz P/O N5530SE50 CBU jlp 20090410

2027-3005 COAXIAL DIRECTIONAL COUPLER F022610 Coupling Coefficient 60dB±1dB at 1.075GHz, ref to output port. Coupling Coefficient Variation± .5dB. Standardize Coupling Coefficient per Freq before use. (Previous) Directivity at 925 to<1050 Mhz ≥33dB. Cal'd w/GR adapter SN 022610 28Feb14

Q8486A POWER SENSOR F041114 SEE CAL CHART; P/O 436A OPT E41; CBU

R8486A POWER SENSOR F041115 SEE CHART; P/O 436A OPT E41; CBU

PPTS 101 PULSE POWER TEST SET F041159 NPC/ Monitor all outputs

778D Directional Coupler F041205 Operational Check Only. Monitor all outputs. NPC

2760 PULSE POWER SOURCE F041230 MONITOR ALL OUTPUTS / CBU / NPC

909A OPT012 Termination J287124 S/N 287124. Cal'd to 1 GHz for VSWR < 1.06

26A-10-026 10 dB Attenuator J287571 DC-18 GHz; 10 dB +/- 0.6 dB

Limitation removed 20170706 ECA

26A-10-026 10 dB Attenuator J287572 DC-18 GHz; 10 dB +/- 0.6 dB

Limitation removed 20170706 ECA

E8257D Signal General J287742 No parameters cal'd above 18GHz (Prev) FM Deviation verified up to 400kHz (TOD) 16Aug13 Due to MMR Spectrum Analyzer limitation Frequency Modulation Deviation verified up to 400 kHz. (TOD) No parameters calibrated above 26.5 GHz. 20150331 QAT FM Deviation verified up to 400 kHz (TOD) 20161102 ECA

26A-3 3 dB attenuator J288011 DC to 18GHz 3 dB ±0.5dB (Prev) 16Aug13

Limitation removed 20170322 ECA

E8257D LOW NOISE SIGNAL GENERATOR J290307 No Parameter cal'd above 18GHz FM Deviation & Distortion cal'd up to 400kHz. Single Sideband Phase Noise ≤-78dBc @ 10hz offset from > 1 to 2 GHz. (TOD) Not cal'd above 18GHz. 16Aug13 Due to lack of standards, the TI FM Deviation and Distortion can only be verified up to 400 kHz and the TI Single Sideband Phase Noise will be limited (TOD). Due to limitation on standard used, Spectral Purity (Nonharmonics) not verified above 26.5 GHz. (LOS) 20170109 ECA

E8257D-520-HA1-UNX-1EA-1E1-UNT LOW NOISE SIGNAL GENERATOR J290309 Monitor All Outputs. P/O E5504BOPT001,406,406,E18 Harmonics verified up to the second Harmonic (16GHz) of the 8GHz carrier frequency. 16Aug13 No limitations 16Sep14 Due to limitation on standard used, Spectral Purity (Harmonic) verified up to the 3rd harmonic at 8000 MHz. (LOS) (20160921 ECA)

478A H73 THERMISTOR MOUNT M035675 See AFPSL Certificate of Calibration; Cal'd from 10 to 1090 MHz - TO Directed Limitation; Model 478A-H73 S/N MY50310001.

SSPA 0.001-1.000-500 POWER AMPLIFIER SYSTEM M036093 Monitor Output with calibrated TMDE. NPC (CON COV) (20170217 ECA)

RF Output (Sampled Output) NOT calibrated. RF Output (Stability) calibrated to <±0.10 dB. (Con Cov) 20170808 ECA

AP BCL-01 Rev. .01

K5

K5 SECTION (ITEMS IN RED HAVE BEEN CHANGED OR ADDED)

TOD = Technical Order Directed CON COV = Contractor Conveniance LOS = Limitation of Standards TEMP = Temporary (One Time Only

P/N NOMENCLATURE ID# LIMITATION

720350-1 THERMOCOUPLE/mVOLT CALIB A223665 K=+/-2.5C/J=+/-2C/T=+/-2C. ENSURE THE CHECK READINGS ARE IN TOLERANCE PRIOR TO USE TO DIRECTED. CHANNEL A CAL'D ONLY. Ch. A mv output Cal'd 0-20mv only. Acc= +/-.03% of Rdg + 8LSD CBU 16Aug13

2190A (W) Y2003 THERMOCOUPLE SIM. CALIB A483005 CAL'D FOR USE WITH J AND K THERMOCOUPLE ONLY. K RANGE -132C TO 0C +/-.4C, USE THERMOCOUPLE CARDS IDENTIFIED AS CALD WITH UNIT ONLY, REFERENCE ZERO TO ICE POINT BEFORE USE. (CBU) 16 Aug 07; designated item CBU Card Cal'd for Type K Only. Card Identified w/shoe tag. (Info) 13 Dec 07

K170-6C ICE PT REF SYS SSA K120-4C A483146 TERMINALS 1 AND 4 CAL'D ONLY CBU 16Aug13 Turn-in 15May14

566 PSYCHROMETER A500169 Cal'd for use as a Psychrometer only. 3/31/08 drj Cal'd at room temperture +/- 1 Deg F T.O. Dir CBU 16Aug13

8113Q PLATINUM RES THERMOMETER A858950 TO DIRECTED LIMITED CALIBRATION. SEE CALIBRATION CERTIFICATE OR CALIBRATION LIMITATIONS AND UNCERTAINTIES. SERIAL NUMBER G91357 DELETE EXCHANGE

CT485B-110V TEMP HUMIDITY RECORDER B111000 Humidity cal'd at 20,50, 80% +/- 4% Tempture cal'd at 50, 77, 104 deg F +/- 2 deg F Cal'd with probe h95T6 Temp cal'd from 50 to 90°F @ 50, 77 and 90°F ±2°F. Humidity cal'd from 20 to 80% @ 20, 50 and 80%RH ±3%RH (Prev) Digital display not cal'd (TOD) 16Aug13 CBU

9210 MINI FIXED-POINT MAINT APPARATUS B111586 NCR 16Aug13

5901B MINI TRIPLE POINT OF WATER CELL B111591 ICO 16Aug13

PHT-770 Hygo-Thermometer B112106 Temp Cal'd @ 45, 65, & 90 Degrees F. Humidity Cal'd @ 20, 50, & 80% RH. P/O AUDITKIT40 (TI S?N: 9335184). [New item added 26 Feb 08. SJN] CBU 16Aug13

1620-S THERMO-HYGROMETER DISPLAY B112201 NCR 16Aug13

2626-S PROBE, TEMP/HUMIDITY B112202 Temperature Accy: ±1ºF & RH Accy: ±3%RH (Prev) 16Aug13 cald to accy: of +/- 1.11 Deg C 20150909 ECA

1620-S THERMO-HYGROMETER DISPLAY B112207 NCR 16Aug13

2626-S Temp/Humidity Probe B112208 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH. S/N A5A633 temp: ±1.1°c RH: 5% RH P/N: 2626-S (CON COV) 20161121 ECA. New ID J289986

1620-S THERMO-HYGROMETER DISPLAY B112209 NCR 16Aug13

2626-S PROBE, TEMP/HUMIDITY B112210 Temperature cal'd to ±1ºF & Humidity cal'd to ±3%RH 16Aug13

1620-S THERMO-HYGROMETER DISPLAY B112242 NCR 16Aug13

2626-S Probe, Temp/Humidity B112243 Temperature Cal'd +/- 1 Deg C. Humidity Cal'd +/- 5% RH. 20150501 QAT

2626-S PROBE, TEMP/HUMIDITY B112243 ` No limitations 16Aug13

2626-S Temp/Humidity Probe B112270 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH.

Temp Accy +/- 1.11 Deg C. Humidity Accy +/- 3% RH (Con Cov) 20150909 ECA

2626-S Probe, Temp/Humidity B112271 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH.

CS77 THERMOMETER SET B194443 THERMOMETER 7707164 NOT CAL'D; ACCURACY +/- 1 DIV ACCURACY +/- 1 DIV, sn:598404, 688695, k643963 Calibrated only/CBU K643963 deleted; broken

402CP45 THERMOMETER C764798 ACCY +/- 1 DEGREE F S/N #1 CBU 16Aug13

402CP45 THERMOMETER C764798 ACCURACY +/- 1 DEGREE F; S/N 1; CBU

402CP45 THERMOMETER C764800 ACCY +/- .4 DEGREE F (2 DIV); S/N #4; CBU CBU 16Aug13

402CP45 THERMOMETER C764801 NPC (ACCY+/- 1 DEGREE F) S/N #3

402CP45 THERMOMETER C764802 NPC (ACCY+/- 1 DEGREE F) S/N #6

CT485B-110V TEMP HUMIDITY RECORDER C875321 TEMP. CAL'D +/-2F. RH CAL'D +/-5% Humidity cal't at 20, 50 and 80 % +/-3% Temperture cal'd at 50,77and 90 degs +/-2 2 degs F CBU 16Aug13

CT485B-110V TEMP HUMIDITY RECORDER C875322 RH CAL'D +/-5%. TEMP CAL'D +/- 2 DEG F Temp cal'd@ 50, 77 & 90 +/- 2 DegF; Humidity cal'd @ 20, 55 & 90 +/-3%RH; Digital display not cal'd ( TO directed) Cal'd w/ temp probe H9A T5 CBU 16Aug13

CT485B-110V TEMP HUMIDITY RECORDER C875323 RH cal'd +/- 5% Temp cal'd +/- 2 deg F; Temp cal'd @40,65 &90 Deg F +/- 2 deg F. Humidity cal'd @ 20, 50 & 80% RH. Digital display not cal'd K295 (T.O. directed) cal'd w/ probe S/N C877523 Deleted 16Aug13

3604 Dry-well Temp.calibration system C875576 TOD Not certified above 900 deg F. Cal'd to 800°F 1/9/09 drj CBU 16Aug13

7000-3 THERMOMETER, LIQUID IN GLASS C897810 CBU 16Aug13

1140B THERMOCOUPLE SIM-CALIBRATOR C908010 TC Connector Termination Not Cal'd Type J and K TC Cal'd Only

(20160831 KAA)

5698-25 STD PLAT RESISTANCE THERMOMETER C911770 See AFPSL Certificate of Calibration 16Aug13

9540A Digital Thermometer E204041 0-60 degrees celsius accy +/- .1degrees celsius New limitation; 3 Jan 08: Cal'd to +/- 0.2 degrees C. Cal'd from -15 to 60 degrees celsius Accy: ±1ºC. Cal'd from 15 to 30º C only. (Prev) 16Aug13

CALD FROM 15°C TO 30°C ONLY ACCY: ±0.2°C (CON COV) 20170711 ECA

5698-25 PLATINUM RES THERMOMETER E289765 T.O. DIRECTED LIMITED CALIBRATION. SEE AFPSL CERTIFICIATE OF CALIBRATION REPORT NO. 053550097; MODEL 5698-25 S/N 95090 Not on file 16Aug13

CT485-110V TEMP HUMIDITY RECORDER F033367 CAL'D +/- 2 DEGREES F; +/- 5% RH Humidity cal'd at 20, 50, and 80% +/- 3%. Temp cal'd at 50, 77 and 90 degress F +/- 2 deg.. Cal'd w/probe H95-T6. Digital readout not cal'd. CBU

2500S HUMIDITY GENERATOR F041540 Low Range Transducer ±0.08psia, High Range Transducer ±0.23psia from 0 to 100psia & ±0.3 16Aug13

Due to the resolution of the TI, the TI Low Range Transducer will be certified to ±0.08psia and the High Range Transducer will be certified to ±0.23psia from 0 to <100psia and ±0.3psia from 100 to 150psia Pre-Saturator and Expansion Valve Probe ACCY: ±0.12°C (TOD) 20160914 ECA

7013 TEMP BATH F041580 NCR 16Aug13

2000M THERMOCOUPLE CALIB/SIMULATOR F041589 CBU 16Aug13

WSP670 PROBE, PRT J287093 CBU 16Aug13

402246 TEMPERATURE SENSOR, AMBIENT J287492 ` No limitations 16Aug13

401100 RH SENSOR, AMBIENT J287494 ` No limitations 16Aug13

2626-S Temp/Humidity Probe J287636 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH. CBU

2626-S Temp/Humidity Probe J287637 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH. (New item added to inventory. 1 Feb 08. SJN)

5626 PRT PROBE J288031 See AFPSL Certificate of Calibration 16Aug13

TVO-2 OVEN J288524 NEC 16Aug13

SERIES 981 TEMPERATURE CONTROLER J288565 NPC 16Aug13

9143-A-P DRY WELL CALIBRATOR J288614 Temperature and Ref PRT cal'd only. RTD,Thermocouple and Millivolt not cal'd No limitation 16Aug13 Temp function cal'd only 20141204 QAT

5616-12 PRT PROBE J288615 See AFPSL Certificate of Calibration 16Aug13

K57 ICE POINT REFERENCE DRY WELL J289498 ` No limitations 16Aug13

K6

K6 SECTION (ITEMS IN RED HAVE BEEN CHANGED OR ADDED)

TOD = Technical Order Directed CON COV = Contractor Conveniance LOS = Limitation of Standards TEMP = Temporary (One Time Only)

P/N NOMENCLATURE ID# LIMITATION

10 GAGE BLOCK SET B111018 ACCURACY: +/- 20uIN. FROM STATED VALUE. See Report of Calibration number 200708294900 dated 28 Sep 2007. S/N 0145. P/O 598-10-18, S/N 0145. Accy: +/- 20u" from state value; See calibration chart; P/O=598-10-18 20081021 jlp Accy: ±20µinch from stated value See Calibration Chart (TOD). .105, .315, .500, .710, .920 Blocks not Cal'd (Prev) 16Aug13

120X E3M1K3A10000 C875018 Accy. +/-2 Div / CBU

1425-24 HOOK GAGE RODS A223512 23" rod +/- .0004", 9" & 7" rods +/- .00035", 11" & 17" rods cal'd +/- .0003". 5" rod +/- .00025", 3" rod +/- .00015"; S/N 21 See Charted Values Deleted 16Aug13

1425-24 Hook Gage Stand B110789 Cal'd +/- 0.0025"H20; Thermometer accuracy not verified P/O 1425-24 Hook Gauge Stand S/N is 35. jlp 13 may 08 CBU 16 Aug13

185 MAGNETIC BACK MIRROR B203638 SEE AFPSL CERTIFICATE OF CALIBRATION; S/N 87133; T.O. DIRECTED LIMITATION; MIRROR FLATNESS < 10.0 uIN over central 90% / CBU SEE AFPSL CERTIFICATE OF CALIBRATION; S/N 87133; T.O. DIRECTED LIMITATION; MIRROR FLATNESS < 10.0 uIN over central 90%

2121254 SSA EAS-3031 SERIES, WUC WAVHW B114400 Metric scales not calibrated; Accy: ± 1 division Gagehead ID B114402 matched to Input B of Amplifier ID B114400; Gagehead ID B114401 matched to Input A of Amplifier ID B114400 (TOD) 20170629 ECA Differential measurements not cald (CON COV) 20170629 ECA

2000-0-C Magnahelic Gage (Airlock) C875010 Cal'd +/- .02" H20. Use in Vertical Position Only Cal'd in Vertical Position only (TOD) Cal'd ±0.02 inches of Water (Prev) 16Aug13

2000-300-3 1LB DISK B111364 Accy: +/- 0.05% Accy: ±0.02% (TOD) 16Aug13

Cald to Table 1 specs 20151221 ECA

2456 Piston gauge Monitor B111496 Perform standardization before use. P/O 2465A series NPC 16Aug13

25-2002-00 MIKE MASTER A223245 CBU

2465-601-58500 PISTONS G151202 SEE AFPSL CERTIFICATE OF CALIBRATION, REPORT NO. 032310113 (T.O. DIRECTED) MODEL 2465/2460-SERIES I.R S/N TL-877 SICL P/O 2465-601-58500 Note on file 16 08 2013

2465-601-58500 PISTONS G151203 SAME AS ABOVE EXCEPT MR S/N C-138 not on file 16 085 2013

2465-601-58500 pistions G151204 SAME AS 63 EXCEPT; HR S/N V-972R Not on file 16 08 2013

2465-601-58500 pistions G151201 SAME AS 63 EXCEPT:2465-781-SERIES S/ 37962 not on file 16 08 2013

3461-1-1, 3461-5-30 P GAGE GPA A495466 ACCY: +/- 2 DIV P/O 3461-1-1 ACCY: +/- 1 DIV P/O 3461-1-1 Cal'd to ±1 div (Prev) 16Aug13

3461-1-1, 3461-5-100 P GAGE GPA B204658 ACCY: +/- 1 DIV P/O 3461-1-1

3461-1-1, 3461-5-300 P GAGE GPA B204659 ACCY: +/- 1 DIV P/O 3461-1-1 CBU 16 08 2013

3461-1-1, 3461-5-10000 PRESS GAUGE A495467 +/- 1div; NOT CAL'D ABOVE 5000PSI 'CBU 16Aug13 - MDC shows DELETED from inventory 20140210 ECA

3461-1-104 3461-35-1000 P GAGE GPM C764275 Not cal'd above 600 psi Cal'd to ±1 div (Prev) 16Aug13

3461-1-104 3460-150-3000 RELIEF VALVE C764276 NCR

3461-1-104 3460-150-1000 RELIEF VALVE C764277 CBU not on file 16 08 2013

CM 3461-35-3000 P GAGE GPM C764278 Cal'd +/- 1 div P/O 3461-1-104 11/18/08 jlp

36 GAGE BLOCK SET G037140 See AFPSL Certificate of Calibration Report No.082420052 Model 36; S/N 121702.7 T.O. Directed Limitation 11/17/08 jlp not on file 16 08 2013

36 GAGE BLOCK SET G037167 See AFPSL Certificate of Calibration Report Number 142470092 - replaces ID G151087 20141126 QAT

384E PARALLEL BARS C875035 NPC No file 16 08 2013

400B5 UNIVERSAL CALIBRATOR C875583 CAL'D @ 73 DEGREES F +/-6 DEGREES F; ACCUACY: 0-0.1 inch +/- 75 u inch; 0-0.5 inch +/- .0001 inch; TO Directed high and low magniciation cal's to +/- 100uin CBU

400594 PISTON POSITION SENSOR J287915 Stnadardization/Verification required every 6 months IAW COM DATA, Operation & Maint. Manual dated 2006; Sensor S/N 7915; P/O PG 7601-SYS-AF 11/07/08 Standardization/Verification required every 6 months IAW Comm Data IAW 00-20-14. Cal'd using operational maintenance manual dated 2008 16Aug13

Standardize every 6 months or if pressure control to float PG7601-AF piston does not operate correctly IAW Operation and Maintenance Manual dated 20071001 (TOD) 20170629 ECA

400915 VACUUM SENSOR J287496 Accy is +/- 0.534 Pa from2 to 5 Pa and +/-0.632 Pa at 6 Pa and +/-0.731 Pa (T.O. Directed) S/N 292 P/O PG7601-SYS-AF Cal'd @ 2, 3, 4 & 5Pa ±.534Pa. Cal'd @ 6Pa ±.632Pa. Cal'd @ 7Pa ±.731Pa (TOD) 16Aug13

ACCY (Pa): 2-5 ±0.534, 6 ±0.632, 7 ±0.731 (TOD) 20170629 ECA

470 SINE BAR CALIBRATOR A221109 FLATNESS OF SURFACE NOT CAL'D. ANGLE CAL'D TO +/- 0.5% OF DEVIATION FROM CENTER (500 ARC SEC) OF MICROMETER OR +/- 0.05 ARC SEC, WHICHEVER IS GREATER. P/N 470, S/N 89106 Flatness of surface not cal'd. Angle cal'd to ±0.5% of deviation from center (500 arc second) of micrometer or ±0.2 arc seconds, whichever is greater. (TOD) 16Aug13

8 GAGE BLOCK SET A991577 SEE CAL REPORT; ACC +/- 5uin /in FROM CHARTED VALUES See Report of Measurement Accy: ±3µinch/inch from stated value (TOD) 16Aug13

Accuracy: ± 3 uin from stated value. See Report of Measurement dated 28-Jul-17 (TOD) 20170811 ECA

568, V BLOCK C875024 NPC No file 16 08 2013

599-750 V BLOCKS C875036 NPC No limitations 16 08 2013

599-920-52 PARALLEL BARS C875030 NPC

599-920-52 PARALLEL BARS C875032 NPC

599-920-64 PARALLEL BARS C875029 NPC

599-920-64 PARALLEL BARS C875031 NPC

599-920-8 PARALLEL BARS C875033 NPC

599-920-8 PARALLEL BARS C875034 NPC

599-920-84 PARALLEL BARS C875037 NPC

599-920-84 PARALLEL BARS C875038 NPC

599-920-88 PARALLEL BARS C875027 NPC

599-920-88 PARALLEL BARS C875028 NPC

7024083 T.I. Setting Standard B112095 PARRALLELISM +/- 40 UIN (T.O. DIRECTED) ICO 16 08 2013

711-T1 DIAL INDICATOR A223249 CAL'D IN CW DIRECTION ONLY; LABEL REACCOMPLISHED 95136; CBU

71-7020S VARIABLE OPT WEDGE J287201 SEE AFPSL CERTIFICATE OF CALIBRATION T.O. DIRECTED LIMITATION: UNCERTAINTY +/-0.5 ARC SEC.

71-7020S VARIABLE OPT WEDGE A498453 SEE CERTIFICATE OF CALIBRATION T.O. DIRECTED LIMITATION: UNCERTAINTY +/-0.5 ARC SEC

750-5 DOSIMETER CHARGER A481725 NCR No file 16 08 2013

779 DIAL COMPARATOR B111440 ACC. +/- .00004 (2 DIV) P/O 779 S/N K1001580 Length Accuracy: ±20µ inch. Hysteresis Accuracy: ±20µ inch (T.O. Directed) P/O779 01Oct13

81 GAGE BLOCK SET, WORKING F041655 Accy. +/- 20 uin from stated value. See cal report. Accessories:Flatness and parallelism cal'd only

82A2X GAGE BLOCKS F041655 SEE REPORT OF MEASUREMENTS Accy: ±20µinch from stated value See Report of Calibration (TOD) 16Aug13

901B Digital Pressure Indicator F272616 Cal'd to +/- 0.04% FS up to 800psi Accy: ±0.5psig. Not cal'd above 600psig. (OWC Request) Zero before use. Cal'd @ 72°F Temperature coefficient ±.004% of span/°F from a reference temperature of 72°F from 45 to 95°F 16Aug13 PSIG range cal’d only. Not cal’d above 600 psig (Prev) ±0.2 psig. Zero before use. Reference Temperature: 71°F. Temperature Coefficient ±0.004% of span/°F from reference temp of 71°F. (TOD)27May14 ACCY: ±0.35 PSIG. Not cal'd above 600 PSIG. CALD IN PSIG ONLY. Zero before use. REF TEMP: 71°F Temperature coefficient ±.004% of span/°F from REF TEMP 20141216 ECA

ACCY: ±0.5 PSI; NOT CALD ABOVE 600PSIG CALD IN PSIG ONLY (CON CONV) 20170427 ECA

9191 RIGHT ANGLE IRON B111253 SQUARENESS CAL'D .0004IN TIR (TO DIRECTED) PARALLELISM CAL'D .0002 IN TIR (20081015 Limitation removed) Parallelism cal'd to 0.0004inch TIR 16Aug13 Squareness checked on sides A & F (TO Directed). Parallelism/Flatness and Squareness calibrated to .0004 inches TIR 20150107 ECA

9192 ANGLE PLATE A222609 NPC No file 16 08 2013

9194 ANGLE PLATE B111424 SQUARENESS ACCURACY; .0005 in TIR, FLATNESS ACCURACY; .0003 IN TIR; made CBU

9228 SINE PLATE B111417 PARALLELISM OF PLATE <300uin See tag for info Only the center 2.5 inches of roll calibrated for Base to Roll Parallelism. (Previous) Angle Measurements meet AFCAV specs: up to 15 Deg: 6.4sec=(31µinch TIR per inch), >(15 to 30 Deg: 10sec=(50µinch TIR per inch), >30 to 45 Deg: 15sec=(75µinch TIR per inch) (TOD) 16Aug13 Angle Measurements meet AFCAV specs: up to 15 Deg: 6.4sec=(31µinch TIR per inch), >(15 to 30 Deg: 10sec=(50µinch TIR per inch), >30 to 45 Deg: 15sec=(75µinch TIR per inch) (TOD) 20140815 PQA Angle Measurements meet AFCAV specs: up to 15 Deg: 6.4sec = (31µin/in TIR), >(15 to 30 Deg: 10sec = (50µin/in TIR), >30 to 45 Deg: 15sec = (75µin/in TIR) (TOD). Parallelism accy: 400uin TIR 20150129 PQA

A6000AF/RPM3 DHI PRESSURE CALIB. F405868 NOT CAL'D BELOW 100 PSIA RANGES H2 AND H3 NOT CAL'D Leak test not performed; run autozero daily when used in gage mode. Run autozero at least every 30 days when used in absolute & when returned from shipment. Accy: +/- .025% of rng P/O HGC-30000-AF drj 5/7/08 TOD Accy: ±0.025% FS of each range. AutoZero swhall be kept on during use. Run AutoZero daily when used in gauge mode. Run AutoZero at least every 30 days when used in Absolute and when returned from shipment 16Aug13

Accuracy: =/-0.025% FS of each range. AutoZ function shall be kept ON during use. Run autozero daily when used in Gauge mode. Run Autozero at least every 30 days when used in Absolute mode and when returned from shipment (TOD) 20170622 ECA

AG16LM ANGLE BLOCK SET A724840 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT NO. 063210097 FOR T.O. DIRECTED LIMITATIONS AND ACTUAL VALUES, MODEL: AG16LM S/N 52584.12 No File 16 08 2013

B SUPER MIC. A480455 MEASURING FORCE ON TAILSTOCK SET AT 16+/-2 OZ. TI NULL METER FOR NULL INDICATION ONLY CBU 16 08 2018

C3H3-1T LOAD CELL 2K E204430 SEE CERTIFICATE OF CALIBRATION / Cal'd with E218783 20150403 QAT

C3H3-10T LOAD CELL 20K E204570 SEE CERTIFICATE OF CALIBRATION / Cal'd with E218552 No file 16 08 2013

C3H3-10T LOAD CELL 20K E289611 SEE CERTIFICATE OF CALIBRATION / Cal'd with E218783 20150403 QAT

C3H3-30T LOAD CELL 60K C936017 SEE CERTIFICATE OF CALIBRATION / Cal'd with E218552 N File 16 08 2013

C3H3-30T LOAD CELL 60K C936015 SEE CERTIFICATE OF CALIBRATION / Cal'd with E218783 20150403 QAT

CS26R-10K-B000 LOAD CELL 5K 10K G151606 SEE CERTIFICATE OF CALIBRATION / Cal'd with E218783 20150403 QAT

CM Gage F022130 Cal'd to +/- 1 div from 0-60 psi and +/- 2 div above 60 pse 9/4/08 Accy: ±1 div from 0 to 60psig & ±2 div above 60 to 100psig (Prev) 16Aug13 Accy: ± 2 div, Cal Temp 72 Deg F, P/O TFCU SeriesII 8Oct14

CP225D Analytical Balance B112255 Perform Internal Calibration before use (and calibration). Calibrated with Control Module, S/N 19012604. New item added 27 Dec 07 (SJN) No limitations 16Aug13

CP34001S Analytical Balance J287354 Peform External Calibration prior to use (and calibration) to achieve certified accuracy. See Note 2 in AFCAV entry. (25 Jan 08, SJN) In order to achieve certified accuracy, perform external calibration prior to use & calibration. Use MMS 10kg (or Class F1 or better) to perform the external calibration. Linearity not cal'd. Direct Readout cal'd ±0.5g, Repeatability cal'd ≤0.1g, Shift Test cal'd ±1g @ 10kg (TOD) 16Aug13

CX1 HEIGHT MEASURING INSTRUMENT G037273 LINEARITY +/- .0002 IN (T.O. DIRECTED) TI accuracy downgraded due to laboratory environment, TI accuracy ±0.0002inches (TOD) 16Aug13

D614-104 PENTA BLOCK A500616 ANGLE=90'-2"; LABEL REACCOMPLISHED 95137 (CBU) This item was exchanged with Hickam's ID# B035809. There's was inop. & this one hasn't been here in over 13 years. Not on file 16Aug13

D614-104 PENTA BLOCK B035809 Actual Angle: 90 deg, 0' 3.1" +/- 1". NRTS-8; (Retaining for inventory Purposes only) CBU 16Aug13

D615 REFERENCE MIRROR A496176 D615, S/N 4823 (CBU) SEE AFPSL CERTIFICATE OF CALIBRATION S/N 4823 T.O. DIRECTED LIMITATION MIRROR FLATNESS ≤ 4.0 UIN

D616 MIRROR C764774 ACCURACY: FLATNESS 0-.000005 INCH MAXIMUM TO DIRECTED (CBU) EXCHANGE STANDARD DELETED 20011205 Not on file 16Aug13

DMP40 DIGITAL FORCE INDICATOR E218552 SEE CERTIFICATE OF CALIBRATION Not on file 16Aug13

DMP40 DIGITAL FORCE INDICATOR E218783 SEE CERTIFICATE OF CALIBRATION

DPG100-250 DIGITAL PRESSURE GAUGE B110093 CAL'D TO +/- 1PSI CBU 16 08 2013

GX-2000 Analytiical Balance J287358 In order to achieve certified accy., perform internal cal. prior to use (and calibration). Direct Readout, Repeatability, and Shift Test cal'd. Linearity not cal'd. (T.O. Dir) In order to achieve certified accuracy, perform internal calibration prior to use & calibration. Direct Readout Accy: ±.1g, Repeatability Accy: ±.01g, Shift Test Accy: ±.02g Cal'd only (TOD) 16Aug13

FCS3ASSC 10-25-.1 P/O FCS3ASSC1 C936247 SEE CERTIFICATE OF CALIBRATION AND DATA SHEET (PART OF FCS-3A-SS-C1KIT # 88-110 S/N 10018 EXCHANGE STANDARD DELETED 20010823

FCS3ASSC 10-25-1 P/O FCS3ASSC1 C936245 SEE CALIBRATION CERTIFICATE AND DATA SHEET (PART OF FCS-3A-SS-C1) KIT # 88-110 S/N 10011 EXCHANGE STANDARD DELETED 20010823

FCS3ASSC 10-25-10 P/O FCS3ASSC1 C936244 SEE CERTIFICATE OF CALIBRATION AND DATA SHEET (PART OF FCS-3A-SS-C1 KIT # 88-110 S/N 10084 EXCHANGE STANDARD DELETED 20010823

FDI-C7009 10-25-0.01 LAMINAR FLOW ELEMENT C936449 SEE CALIBRATION CERTIFICATE; P/O FDI-C7009 LAMINAR TEST SET 84-172; "NOT OXYGEN CLEAN" S/N 8858 no File 16 08 2013

FDI-C7009 10-25-.1 LAMINAR FLOW ELEMENT C936448 SEE CALIBRATION…