07-R-8507-001 Attachment1 PWSRevised5Mar08.doc

FA2521-07-R-8507

ATTACHMENT NO. 1

PERFORMANCE WORK STATEMENT (PWS)

FOR

REFUSE COLLECTION AND DISPOSAL SERVICES

PATRICK AIR FORCE BASE (AFB),

CAPE CANAVERAL AIR FORCE STATIONS (AFS), AND

KENNEDY SPACE CENTER (KSC)

FLORIDA

12 FEB 08

REVISED 6 MAR 08

TABLE OF CONTENTS

Paragraph

Number Title

Page No.

Section 1 –

Description of Services

Scope of Work

1.1 Refuse Service Plan Requirements

1.2 Refuse Collection and Disposal

3 - 4

1.3 Collection Area Maintenance

1.4

Equipment and Vehicle Maintenance

1.5 Special Events/Base Projects

1.6 Disposal

4 - 5 Section 2 – Services Summary

2.1 Services Summary (SS)

Section 3 – Government Furnished Property, Equipment and Services

3.1 General

3.2 Security Forces (SF) and Fire Protection

Section 4 – General Information

4.1

Personnel

4.2

Quality Control

8 - 9 4.3

Quality Assurance

4.4

Contractor Furnished

4.5

Government Remedies

4.6

Environmental Requirements

9 - 10

4.7

Permits, Licenses and Certifications

4.8

Hours of Operation

4.9

Recognized Holidays

10 - 11

4.10

Security Requirements

10 - 11

4.11

Safety Requirements

4.12

Phase-In/Phase-Out Requirements

Appendices

A

Definitions

12 - 13 B

Historical Workload Data

B-1 CCAFS Refuse Collection Sites and Container Information 15 - 20 B-2

PAFB Refuse Collection Sites and Container Information 21 - 26

B-3 KSC Refuse Collection Sites and Container Information 27 - 30

C

Maps and Work Area Layouts

D

Data Requirements

SECTION 1

DESCRIPTION OF SERVICES

1. SCOPE OF WORK. The contractor shall provide all management, labor, equipment and vehicles with the exception of Government-Furnished Property/Equipment necessary to provide solid waste, refuse and garbage collection and disposal services for Patrick Air Force Base (PAFB) to include Malabar annex, Cape Canaveral Air Force Station (CCAFS),and Kennedy Space Center (KSC), as well as approximately 524 Military Family Housing (MFH) units located at PAFB. Disposal shall primarily be accomplished at the Brevard County Landfill unless otherwise designated below.

1.1 REFUSE SERVICE PLAN REQUIREMENTS. The Contractor shall develop a plan to include collection routes and collection schedules for each installation for all services called out under this contract. Address in the plan both management and operational procedures for the performance of required services. Provide in the plan, a description of practices and procedures to be used with sufficient detail to demonstrate that the practices and procedures to be used are commercially acceptable and in compliance with applicable local, state and federal regulations and laws. Address compliance with environmental requirements and record keeping and reporting requirements. Contractor shall develop and implement a system that will ensure all refuse efforts are accurately tracked and documented to include accurate IDIQ quantities and landfill tipping fees for each installation. Contractor shall submit entire plan to the Contracting Officer (CO) within 15 calendar days after contract award for review and approval. Once the plan, routes, and schedules are approved, provide 5 calendar days notice to the Contracting Officer when changes are necessary. The Contractor shall notify QAP of any conditions that may interrupt the schedule of performance such as, delays due to disposal site availability, security measures, exercises, vehicle breakdowns, blocked containers, etc. Collection as a result of these delays shall be performed by the next workday.

1.2. REFUSE COLLECTION AND DISPOSAL. Provide containers, collect, remove and dispose of all solid waste, refuse,garbage and other waste products identified herein and at locations identified for each installation. Refer to appendices for collection sites, locations and schedules. Contractor shall schedule pickups for all containers in order to prevent filling above capacity. If containers are 80% full, or more, then the container shall be emptied completely. Contractor shall pick up all spillage and overflow waste around all containers to a 6-foot radius.

1.2.1. MILITARY FAMILY HOUSING (MFH).

1.2.1.1. MFH Solid Waste. Collect and dispose of all refuse in containers at MFH units are up to forty (40) gallon general purpose containers. Collection shall be scheduled and performed in accordance with Appendix B.

1.2.1.2. MFH Yard Waste and Bulk Items. Collect and dispose of all yard waste (green waste) and bulk items, including but not limited to, washer/dryers, refrigerators and furniture. Collection shall be scheduled and performed in accordance with Appendix B.

1.2.2 INSTALLATION WIDE.

The contractor shall provide all containers to include dumpsters, roll-offs and general purpose cans, except those identified as Government Furnished, to facilitate refuse collection and disposal services as identified in this PWS and appendices. The contractor shall position containers as requested by the QAP. This may require repositioning of containers from time to time. Containers should be positioned in a manner that minimizes interference with adjacent parking areas, sidewalks, roadways, overhead utilities, trees, and other potential obstructions. Refuse from dumpsters, roll offs and general purpose cans shall be collected and removed in a manner that will not allow for any containers to overflow at anytime.

1.2.2.1 BULK ITEMS, WOOD RECYCLABES AND GREEN WASTE CONTAINERS. Installation wide bulk, green waste and wood items shall be scheduled for pick up and disposal weekly and as required.

1.2.2.2 METAL COLLECTION CONTAINERS. Metal recyclables shall be scheduled for pick up and disposal at Defense Reutilization Marketing Office (DRMO), CCAFS as required.

1.2.2.3 REGULATED FOOD WASTE CONTAINERS. Shall meet minimum requirements of the Department of Agriculture. Waste shall be collected and removed within 48 hours from notification by the QAP.

1.2.2.4 MALABAR ANNEX. Container shall be scheduled for pick up and disposal bi-weekly and as requested by the QAP.

1.3. COLLECTION AREA MAINTENANCE. The contractor shall return all containers to their original location after servicing, in an upright position with the lids closed. The contractor will also be responsible for immediately cleaning up any spill, debris, etc., which may occur during servicing of containers. All refuse on the ground within 6 feet of a container, whether spilled by the contractor or placed there by installation personnel, shall be picked up by the contractor during each collection. The contractor is responsible for keeping all collection areas free of refuse and debris.

1.4. EQUIPMENT AND VEHICLE MAINTENANCE (reference paragraph 4.4, Contractor Furnished).

1.4.1. Bulk Containers. Contractor furnished bulk containers shall all be painted the same shade of dark brown. Color of containers and paint shall be submitted on the AF Form 3000 to the Contracting Officer or QAP for approval prior to placing or painting containers. The contractor shall repaint all bulk containers as required. Containers will be free of unpleasant odor, dirt, grease, stains, debris, visible holes and damage. Maintenance shall be performed as required. The contractor shall furnish replacement bulk containers for any container that is removed for more than 2 hours due to cleaning, painting, maintenance or repair. All containers must remain in good, working condition. All bulk containers shall be leak proof, have lids and doors fully and easily operable and prevent rodents from entering the containers. The contractor shall be responsible for insuring that container plugs are in place and functional throughout the period of the contract. All container lids/doors shall be closed by the contractor after each servicing and additionally whenever observed to be open. Contractor shall not conduct maintenance, painting, repairs or cleaning of any bulk container on government property.

1.4.2. Vehicles. All vehicles, trailers and other vehicles used for refuse collection shall be washed as required to ensure they are free of odor, dirt, debris and pests. If the contractor’s vehicle should break down, it must be removed by the end of that work day. Contractor shall not conduct maintenance, painting, repairs and/or cleaning of any contractor vehicle, trailer, etc. on government property.

1.5. INDEFINITE DELIVERY/INDEFINITE QUANTITY (IDIQ) SPECIAL SERVICES.

1.5.1. The following services shall be priced separately in accordance with the cost indicated in schedule B. The contractor shall be compensated IAW the prices specified in Section B, Price Table for that service. All unit prices shall include all associated fees for container rental, container movement/relocation and all other costs associated with collection and disposal service. The contractor shall deliver the container(s) empty, within 1 day of notification, empty as required and remove container within 1 day of notification. Disposal “tipping” fees shall be applied as stated in paragraph 1.6 below.

1.5.2. IDIQ services are required for special events and/or projects which may include, but are not limited to, additional and/or unscheduled pick ups, installation special events (July 4 Celebration, Air Show, Launch Viewings), special projects (mobility exercise), asphalt/concrete disposal, and mission essential or emergency response as directed by the Contracting Officer or QAP.

1.5.3. BEACHSIDE CONTAINERS. Special pick-up on weekend and/or holiday for PAFB beachside containers as directed by the Contracting Officer or QAP.

1.6. DISPOSAL.

1.6.1. Off Base Disposal. The contractor shall transport and dispose of all solid waste at the Brevard County landfill located at, 2250 Adamson Road, Cocoa, FL. Disposal fees at the county landfill will be billed to and paid directly by Government on separate contract. Refuse contractor shall use separate accounts for each installation identified in Section B and separate weight tickets and report by installation. Refuse disposal shall be in accordance with existing local, state, and federal regulations. The contractor shall be responsible for any additional amounts associated with permits, licenses, fees (charges), etc. which may be necessary for the performance of the required services.

1.6.2. Weighing of Vehicles. All vehicles used in the collection of refuse materials shall be weighed on state certified vehicle scales before arriving at the base and on state-certified scales at the landfill. Incoming and outgoing vehicle weights shall be recorded on weight tickets provided by the operator to determine the amount of refuse tonnage collected on the base.

1.6.3. The contractor shall transport and dispose all regulated food waste from designated containers off base in accordance with federal, state and local regulations, to include Department of Agriculture procedures. All disposal costs incurred shall be included in the unit price for the service.

1.6.4. All disposal costs incurred for asphalt and/or concrete, green waste, wood, recycling efforts or any other disposal that is not transported and disposed at the Brevard County landfill shall be included in the unit price for the service as identified in Section B of the contract.

1.6.5. All recyclable scrap metals from designated metal containers shall be transported to the CCAFS DRMO facility, Bldg No. 66620 for recycling.

1.6.6. Disposal Report. The contractor shall develop and submit for approval to the Contracting Officer not later than 15 calendar days after award a solid waste disposal report format. The approved solid waste disposal report and corresponding weight tickets for each installation shall be submitted every month to the appropriate QAP not later than the fifth (5) working day of the month following the completed billing period. This report and proper weight tickets shall be broken down into distinct categories for each installation as follows:

1.6.6.1. PATRICK AFB CLINS:

Front load solid waste

Roll off green waste

Industrial roll off

Wood recycling

Regulated food waste Military Family Housing solid waste

Military Family Housing bulk & yard waste

1.6.6.2. CAPE CANAVERAL CLINS:

Front load solid waste

Industrial roll off Metal recycling Wood recycling

Regulated food waste

1.6.6.3. KENNEDY SPACE CENTER CLINS:

Front load solid waste

Industrial roll off

Regulated food waste

SECTION 2

SERVICES SUMMARY

2.1. SERVICES SUMMARY (SS). The Contractor service delivery requirements are summarized into performance objectives that relate directly to standards of performance required to meet mission essential needs. For the Performance Objective to be met, service delivery must be in substantial compliance with applicable performance standards. The Performance Threshold describes the minimum overall levels of service delivery required for acceptable quality control. Failure to meet these Performance Thresholds means that contractor Quality Control is unacceptable.

complaints per month.

Collection area free of debris.

Provide timely, complete and accurate reports

per installation

SECTION 3

GOVERNMENT FURNISHED PROPERTY, EQUIPMENT AND SERVICES

3.1 GENERAL. The Government will provide items identified below for contractor use in support of the requirements of this contract. The storage site is provided “as is”. Obtain Contracting Officer approval in advance of making any changes to the site. Such changes will be at no cost to the Government unless otherwise approved by the Contracting Officer. The Government reserves the right to reallocate and relocate assigned storage site area during the term of the Contract. Upon completion or termination of this Contract, or upon such reallocations or relocations, return storage site area to the Government in the same condition as at initial issue to the Contractor, reasonable wear and tear excepted, or as otherwise approved by the Contracting Officer.

3.1.1 Storage Site. The Government will provide approximately 60,000 square feet of open outdoor storage space, which can be used for storage of excess dumpsters and rolloffs used on Patrick AFB. This area is located at the North West corner of the berm area on Control Road, Patrick AFB.

3.1.2 The contractor is responsible for keeping the site and surrounding areas in a clean and orderly condition at all times. All contractors’ property, equipment and supplies shall be removed within one (1) week of contract expiration.

3.1.3 Containers. General Purpose containers ranging up to 55 gallon in size are placed around base property and are to be emptied by the contractor but will be provided and replaced by Government as needed. Locations are identified in Appendix B.

3.1.4 MFH containers up to 40 gallon in size will be picked up by the contractor but will be provided and replaced by the Government as needed.

3.2 Security Forces (SF) and Fire Protection. The Government will provide general security and fire protection services. Emergency phone numbers are as follows:

· Patrick AFB:

· Security Desk

· Kennedy Space Center:

7-911

867-911

SECTION 4

GENERAL INFORMATION

4.1. PERSONNEL.

4.1.1. Contract Manager. The Contractor shall provide a contract manager who shall be responsible for the performance of the work. The name of this person and alternate(s) who shall act for the Contractor when the manager is absent shall be designated in writing to the Contracting Officer. Subsequent changes to these designations of contract manager shall be submitted to the Contracting Officer.

4.1.1.1. The contract manager or alternate shall have full authority to act for the Contractor on all contract matters relating to daily operation of this contract.

4.1.1.2. The contract manager or alternate shall be available during normal duty hours within 60 minutes (1 hour) to meet on the installation with government personnel designated by the Contracting Officer to discuss problem areas. After normal duty hours the manager or designated alternate shall be available within 120 minutes (2 hours).

4.1.1.3. The contract manager and alternate(s) must be able to read, write, speak, and understand English.

4.1.1.4. Unless otherwise notified by the QAP, the Contract Manager shall meet with the QAP weekly at a mutually agreeable time/place to discuss inspections/discrepancies, corrective actions taken, and other issues.

4.1.2. Employees. The Government has the right to restrict the employment under the contract of any Contractor employee, or prospective Contractor employee, who is identified as a potential threat to the health, safety, security, general well being or operational mission of the installation and its population.

4.1.2.1. All personnel employed by the contractor in the performance of this contract, or any representative of the contractor entering the government installation, shall abide by all security regulations of the installation. 45 SWI 31-102 for PAFB, 45 SWI 31-101 for CCAFS, and NPR 1600.1 for NASA.

4.1.2.3. Contractor personnel shall present a neat appearance and be easily recognizable as a contractor employee. Contractor personnel shall wear appropriate clothing and closed-toe shoes at all times while on duty. Contractors shall not wear military clothing while performing duties on any installation.

4.1.2.4. The Contractor shall ensure employees have the necessary professional certifications required to perform duties on this contract prior to commencement of work in accordance with the standards set forth in the PWS.

4.1.2.5. Contract personnel driving motor vehicles shall be in possession of valid and current State drivers license for type of vehicle operated.

4.1.2.6. The Contractor shall not employ any person who is an employee of the United States Government if the employment of that person would create a conflict of interest nor shall the Contractor employ any person who is an employee of the Department of the Air Force, either military or civilian, unless such person seeks and receives approval in accordance with DoDD 5500-7. In addition, the Contractor shall not employ any person who is an employee of the Department of the Air Force if such employment would be contrary to the policies contained in AFI 64-106, paragraph 3.

4.1.3.

Employee Management. Provide continued service under this contract during periods of labor unrest such as walkouts, work slowdowns, and strikes.

4.2. QUALITY CONTROL.

4.2.1 The policy of the Government for Contractor Quality Control and applicable definitions are provided in the Federal Acquisition Regulations in Part 46. In all Government contracts, the Contractor is required to control the quality of service delivery and offer to the Government for acceptance only services which conform to contract requirements. The overall control of quality must meet the specified performance thresholds for each requirement in the Services Summary.

4.2.2 Develop and maintain a quality management system acceptable to the Government to ensure that specified refuse collection and disposal services are performed in accordance with established commercial practices and procedures and meet all applicable performance standards. Provide a written description of the quality management system to include identification of the commercial practices and procedures to be used. Include the inspection system requirements of FAR 52.212-4.

4.3. QUALITY ASSURANCE. The Government will assess the Contractor’s performance on a continuous basis. The primary approach will be to assess the Contractor’s quality management system and when it is found to be acceptable, the Government will use the contractor’s quality data for acceptance and payment purposes. The Government will perform inspections to validate the accuracy, timeliness, and truthfulness of the Contractor’s quality data. Unsatisfactory performance is performance below the required performance threshold identified in the services summary. Each required service will be assessed against applicable performance objectives and thresholds using a combination of techniques including, but not limited to, customer complaints and on-site inspections.

4.4. CONTRACTOR FURNISHED . The contractor shall provide, install and maintain all equipment and vehicles necessary to perform the requirements of this contract. Contractor vehicles shall have the company name prominently displayed on both sides of the vehicles and be maintained clean to present a neat and professional appearance. Contractor vehicles shall be used solely for the intended purpose of performing services in this PWS.

4.4.1. All equipment and vehicles used in the performance of this contract shall be in good operable condition and meet the local, state, and federal safety requirements. Equipment and vehicles found to be unsafe and unable to function as designed shall be removed from the installation and replaced at contractor expense. Vehicular repairs shall not be done on base. The installation safety officer may inspect the contractor’s equipment and vehicles at any time and advise the CO to direct removal of any unsafe or unusable equipment or vehicle from the installation.

4.4.2. All vehicles shall be registered, licensed, insured and operated in accordance with state of Florida laws by a licensed driver.

4.4.3. The contractor shall provide adequate numbers of equipment and vehicles to perform the requirements of this contract. In addition, the contractor shall maintain or have backup capability to provide continued service in the event primary equipment or vehicles are down for extended maintenance or repairs. Equipment failure shall not alleviate the contractor from performing any requirement contained in this contract.

4.5. GOVERNMENT REMEDIES. When Contractor service delivery is unsatisfactory, the Government will order re-performance when it is in the best interest of the Government. As a matter of policy, re-performance is the preferred remedy. If re-performance is not possible or otherwise in the best interest of the Government. the Government will reduce the Contractor’s payment to reflect the loss in value received.

4.6. ENVIRONMENTAL REQUIREMENTS. The Contractor is responsible for complying with all federal, state, Air Force, and local rules and regulations, all applicable environmental regulatory permits and all current 45 SW Management/Operating Plans to ensure environmental compliance at all times. The Contractor shall demonstrate compliance with all changes to rules and regulations during the contract period. The 45 SW Environmental Office is the single point of contact with all regulatory agencies concerning Air Force issues such as: regulatory interpretation, compliance reporting, inspections, and spills or releases.

4.6.1. Environmental Release Notification, Response and Clean-Up. The contractor shall follow all spill notification and response procedures established in the 45 SW CEMP 10-2 Volume II and the 45 SW OPLAN 19-14. The contractor shall discontinue use of all leaking/damaged equipment until it is repaired. Note: 45 SW CEMP 10-2, Vol II is currently titled 45 SW Full Spectrum Threat Response (FSTR) Plan 10-2, Vol II.

4. PERMITS, LICENSES AND CERTIFICATIONS. Unless otherwise specified in this contract, obtain necessary permits, licenses, and certifications; give all required notices; and comply with applicable federal, state, county, and local laws, codes, and regulations in performance of the requirements of this contract. Maintain records of such requirements and make the documentation available to the Government for review.

4. HOURS OF OPERATION.

4. Hours of Operation. The contractor shall perform services required under this contract during the following times: Military Family Housing collection will be accomplished during the hours of 6:30 AM through 2:30 PM (local time), Monday thru Friday. All other services will be accomplished between the hours of 6:00 AM through 4:00 PM (local time), Monday through Friday. Exceptions to hours of operation shall be requested by the contractor and approved by the Contracting Officer. Special events and projects shall be accomplished during hours of operation requested by the Contracting Officer or QAP.

4. Inclement Weather Schedule. The contractor shall collect refuse during periods of inclement weather. In cases of severe weather, the contracting officer or designated representative may authorize exceptions. When an exception is authorized due to severe weather the contractor shall make up missed collections within twenty-four hours after the severe weather has terminated.

4. Holiday Pick-up. The contractor is not required to provide services scheduled that fall on Federal Holidays. The contractor shall provide any missed services the next working day following the Federal Holiday in addition to their regularly scheduled collections, in accordance with the terms of this statement of work.

4.9. RECOGNIZED HOLIDAYS. The contractor is not required to provide service on federal holidays, except in emergency situations; the holidays are:

· New Year’s Day - 1 January

· Martin Luther King Day - 3rd Monday in January

· Washington’s Birthday - 3rd Monday in February

· Memorial Day - last Monday in May

· Independence Day - 4 July

· Labor Day - 1st Monday in September

· Columbus Day - 2nd Monday in October

· Veteran’s Day - 11 November

· Thanksgiving Day - 4th Thursday in November

· Christmas Day - 25 December

4.10. SECURITY REQUIREMENTS. The contractor shall comply with local security procedures and requirements for entrance to Department of Defense facilities, USAF controlled areas, and USAF restricted areas. The contractor shall obtain necessary identification and provide documentations for completion of personnel and security investigations required for entry into the USAF controlled and restricted areas. The contractor must obtain favorable trustworthy National Agency Check Investigations for its employees for entrance to restricted areas. The contractor shall provide escorts for short-term work in restricted areas for contractor employees without restricted area access.

4.10.1. Anticipate delays in getting commercial vehicles on base and allow time for commercial vehicles to reach their destination by driving designated routes at posted speed limits through out the base. Procedures for commercial vehicle access to the base are subject to change without prior notice.

4.10.2. CCAFS Launch or Hazardous Operations: During such operations the contractor will be required to clear out of these areas as directed by Security Forces.

4.10.3. Specific badging and base entry procedures will be provided at time of award.

4.11. SAFETY PROGRAM. The contractor shall;

4.11.1. Establish and manage a comprehensive safety program as required by OSHA Federal regulations and any references adopted by OSHA. This program shall include industrial and construction safety and operations monitoring for the resolution of unsafe acts or conditions. Injuries, damage and close calls resulting from contractor activities shall be thoroughly investigated and have appropriate corrective action taken. Close calls with the potential to have been a type A through D mishap as defined in AFI 91-204 shall be reviewable by the Air Force. The program shall include surveillance of hazardous operations performed by the Contractor’s employees.

4.11.2. Contractor shall prevent injuries to non-contractor personnel or property. Report all anomalies including OSHA recordable mishaps, and verbally report immediately to the 45th SW Safety Office. Contractor shall also provide electronic or hard copy of the report within four (4) hours to customer provided addressee list per AFI 91-204, and 91-224.

4.11.3. Process Safety Management (PSM). The contractor shall establish and implement a Process Safety Management program that meets the requirements identified in Code of Federal Regulations 29 CFR 1910.119.

4.11.4. The contractor shall prepare a PSM compliance plan that describes the tasks required to achieve PSM compliance. The PSM compliance plan shall define the facilities, systems, and equipment interfaces for the IOMS contract covered processes, and priority for accomplishment of process hazard analyses (PHAs). PHAs shall adequately identify, evaluate, and recommend controls for the hazards involved in the covered processes.

4.11.5. Transportation Safety. All modes of transportation for personnel or hazardous material shall comply with applicable standards of the Federal Highway Administration, U.S. Coast Guard, and Federal and state Departments of Transportation (DoT).

4.12. PHASE-IN/PHASE-OUT REQUIREMENTS.

The contractor shall make an effort to facilitate cooperation between contractors phasing-in and phasing-out. The contractor shall provide a Phase-In Plan to the contracting officer after award, but not later than 1 September 2008. The contractor shall supply all necessary tools, equipment, personnel and vehicles to perform proper phase-in. Work shall be accomplished during normal hours and all containers shall be sited as specified in Appendix C or as identified by the contracting officer or QAP prior to 1 Oct 08. Contractor shall use existing enclosures (if applicable) and all debris generated from phase-in operations shall be removed. Phase-Out shall be conducted in a reverse order of the phase-in.

APENDIX A

Definitions Bulk Items. Large items such as non-Freon appliances, furniture, non-hazardous junked auto parts, tree limbs, stumps, and construction and demolition debris generated by households. For MFH units, any large item described in this definition that does not fit into the occupant’s container is classified as a bulk item.

Bulk Waste. Includes large items of solid waste such as appliances, furniture, large auto parts, trees, branches, stumps and other oversize wastes whose large size precludes or complicates their handling by normal collection, processing or disposal methods.

Compactor Collection Truck (Front or Rear Loader). Enclosed vehicle provided with mechanical devices for loading the solid waste into the main compartment of the body and for compressing and distributing the solid waste within the body.

Construction and Demolition Debris. Roofing, non recyclable wood, bricks, and similar materials associated with construction or demolition of buildings, pavements, and other structures.

Container. A solid waste receptacle with closely fitting operational lids which is leak proof and rodent proof.

Contaminants. Any material found in a refuse or recycling station container that is not specifically designated for that receptacle.

Curbside Collection. Collection of solid waste and refuse placed in containers at the side of the roadway in Military Family Housing areas.

Disposal Fee. A fee, usually dollars per ton or cubic yard, charged for the unloading or dumping of waste at a landfill, transfer station, material recovery facility, or waste-to-energy facility.

Dumpster. A large receptacle that can either be pulled or lifted manually or mechanically onto a service vehicle used for the temporary storage of refuse. For the purposes of this PWS, a dumpster will be defined as a 2, 4, 6, 8 cubic yard (cy) container.

Food Waste. Animal and vegetable waste resulting from the handling, storage, sale, preparation, cooking and service of foods.

Garbage. Includes all kitchen and table food waste, and animal or vegetable waste that attends or results from the storage, preparation, cooking or handling of food stuffs.

Green Waste. Grass, tree limbs, stumps, leaves, pine needles, brush, and Christmas trees etc. in which the single item weighs less than seventy (70) pounds or does not exceed six (6) feet in length.

Hazardous Waste. Includes any waste material or mixture of wastes which is toxic, corrosive, flammable, an irritant, a strong sensitizer, which generates pressure through decomposition, heat or other means, if such a waste or mixture of wastes may cause substantial personal injury, serious illness or harm to humans, domestic animals, or wildlife, during, or as an approximate result of any disposal of such wastes or mixture of wastes as defined in Article 2, Chapter 6.5, Section 25117 of the Health and Safety Code.

Refuse. Includes all household-generated waste, non-hazardous commercial and industrial waste, food waste, green waste, construction and demolition debris, and other similar nonhazardous waste material intended for disposal. Not included are explosives and incendiary waste, and contaminated waste from medical and radiological processes.

Refuse. "Refuse" includes garbage and rubbish.

Regulated Food Waste. Garbage and unused food originating outside of the U.S. which shall be handled according to USDA requirements to prevent the dissemination of foreign pest and diseases that pose a danger to U.S. public health and agriculture. Requirements requirements are specified in 7 CFR 330. Refer to the U.S. Department of Agriculture for additional information Roll-off. A large, stationary, steel box used to store bulk waste that can be rolled onto a truck and taken to a disposal site, then returned to the original or another site. For purposes of this PWS, a roll-off shall be defined as any 10, 20, 30 or 40 cubic yard (cy) container.

Rubbish. "Rubbish" includes non-putrescible solid wastes such as ashes, paper, cardboard, tin cans, yard clippings, wood, glass, bedding, crockery, plastics, rubber by-products or litter.

Sanitary Landfill. A site where refuse is disposed of using an engineered method in a manner that protects the environment meeting the criteria of federal regulations and applicable State solid waste management rules.

APPENDIX B

HISTORICAL WORKLOAD DATA

Historical Workload Data. The information presented below is provided as a guide to the Contractor in estimating manpower, workload and scheduling requirements. Tonnage is an average historical annual quanitity. Frequencies are based on disposal records. Variations shall not constitute grounds for an equitable adjustment.

CAPE CANAVERAL AFS

Front Load Solid Waste

1210 TN

2 x Week Industrial Roll Off

538 TN

1 x Week

Regulated Food Waste

1000 LBS

Recycle Wood

17 TN

Scrap Metal

13 TN

Non-Hazardous blast media

24 TN

1 x Bi-Week

PATRICK AFB

Front Load Solid Waste

1,235 TN

1,000 TN

Military Family Housing Solid Waste 800 TN

2 x Week Green Waste

150 TN

1 x Week Regulated Food Waste

700 LBS

Recycle Wood

12 TN

Asphalt/Concrete

180 TN

As required

KENNEDY SPACE CENTER

Front Load Solid Waste

2500 TN

140 TN

Regulated Food Waste

200 LBS

WORKLOAD DATA IS BASED ON HISTORICAL DATA AND MAY VARY.

APPENDIX B-1

CCAFS REFUSE COLLECTION SITE AND CONTAINER INFORMATION

Overflow)

Total

Overflow)

Total

Overflow)

Total

Total

Total

Overflow)

Total

APPENDIX B-2

PAFB REFUSE COLLECTION SITE AND CONTAINER INFORMATION

Overflow)

Total Dumpsters

ROLL-OFFS

Overflow)

Total Roll-offs

COMPACTORS

Total Compactors

GENERAL PURPOSE CANS

North Beach Pavilion & Beach

G.P. Cans

G.P. Cans 30 gal

55 gal

Total General Purpose Cans

REGULATED FOOD WASTE CONTAINERS

MILITARY FAMILY HOUSING UNITS

(524 is the number of houses to pick up from, not number of containers)

APPENDIX B-3

KSC REFUSE COLLECTION SITE AND CONTAINER INFORMATION

Frequency

Overflow)