ESBD_363502_1721661117716_Attachment H1 - Revised Project Drawings.pdf

For the best experience, open this PDF portfolio in

Acrobat X or Adobe Reader X, or later.

Get Adobe Reader Now!

http://www.adobe.com/go/reader

ENGINEERS, INC.

PO Box 362, 2504 CR 911

Joshua, TX 76058 817..360..2900 faiengineers.net

PROJECT NO. 20-104-ABL

ABILENE SSLC – ABILENE, TX

GENERATOR REPLACEMENT – PHASE B

ADDENDUM DATED 7/22/2024

CONSTRUCTION DOCUMENTS

The following sheets are revised and included as part of this Addendum:

Sheets E2.03, E2.04, E2.06 Sheets E3.00, E3.01, E3.02, E3.03 Sheets E4.00, E4.01, E4.02 Sheets E5.00, E5.01, E5.02, E5.03, E5.04, E5.06 Sheet E7.01 Sheet E8.02 Sheet E9.00 Sheet E10.01 Sheet E11.02 Sheet E12.02 Sheet E13.01 Sheet E20.03 Sheet E30.01 Sheets E31.01, E31.02, E31.03, E31.04, E31.05 E31.06, E31.07 Sheet E40.01

The above sheets correspond to the answers to the Contractors questions as attached and included as Part of this Addendum.

GENERATOR REPLACEMENT

PROJECT No. 20-104-ABL

PHASE B

ABILENE STATE SUPPORTED LIVING CENTER

TEXAS HEALTH AND HUMAN SERVICES COMMISSION

LOCATION PLAN (ABILENE, TX) VICINITY MAP

FOR

Project Directory

HHSC Maintenance and Construction:

Texas Health and Human Services Commission P.O. Box 12668 Mail Code 2064 Austin, TX 78711-2668 (909 W. 45th Street, Bldg. 633, Austin, TX 78751)

(512) 206-5911

Austin

Renu Razdan - Director Roger Brigance - Senior Director of Construction Services

(512) 206-5204

Project Manager Jason Staggs Project Manager Facility Maintenance and Construction Austin, TX 78751

(830) 777-4283

Facility Plant Maintenance Manager Kenny Day Plant Manager 2501 Maple Street Abilene State Supported Living Center Abilene, TX 79602

(325) 795-3582

Engineer Larry W. Akers, LEED Green Associate FAI Engineers, Inc.

2504 CR 911, P.O. Box 362 Joshua, TX 76058

(817) 296-8167

AutoCAD SHX Text www.faiengineers.net

SET NO.

DATE: APRIL 15, 2024

PROJECT NO. 202001800

TEXAS BOARD OF PROFESSIONAL ENGINEERS F-298

MECHANICAL ELECTRICAL PLUMBING FIRE PROTECTION

FOR CONSTRUCTION

NORTH

NOT TO SCALE

ABILENE, TEXAS

JOB SITE

202001800

APRIL 15, 2024

STATUS:

SHEET NO.

PROJECT NO:

DRAWN BY:

DESIGN BY:

DATE:

SHEET TITLE:

CHECKED BY:

REVISIONS

FAI - 2023C

LWA

w

.fa ie ng in ee rs .n et

TE

X A

S

BO

R

D O

F

PR

FE

SS

IO

N

L

EN

G

IN

EE

F-

M

EC

H

IC

EL

TR

PL

U

BI

IR

E

CT

LE

ST

PP

IV

C

EA

LT

ER

V

ES

IS

SI

TO

EP

LA

CE

T

JE

o.

0-

4-

BL

PH

SE

B

MAA

G.1

GENERAL SITE PLAN

1 GENERAL SITE PLAN

GENERAL NOTES

NOTES BY SYMBOL

1 ST STREET

2 ND STREET

3 RD STREET

3 RD STREET

4 TH STREET

5 TH STREET

6 TH STREET

7 TH STREET

7 TH STREET

24 TH STREET

24 TH STREET

MAPLE STREET

PLUM AVENUE

SERVICE AVENUE

WALNUT AVENUE

PALM AVENUE

LAKESIDE DRIVE

SERVICE AVENUE

PLUM AVENUE

8TH STREET

PARTIAL PLAN

ENCHANTED BARN

MEGA UNIT

OFFICES

GUEST

HOUSE

STORAGE

GUEST

RED STORAGE

BARN

BARN/

RESIDENCE

LA 5962

S/A 5961

SEWING/

REIMBURSEMENT

WATER HEATER

ACTIVITY

CENTER

WATER HEATER

MAINTENANCE

HAZMAT

BIG BLUE

MOTOR POOL

WELDING SHOP

FLAMMABLE

CARPENTRY

SHOP

LUMBER

TETC #3

TETC #2

QUONSET

BLDG

TETC #1

MATERIALS

LA 6350

LA 6330

CHILL H20 #1

LA 6360

ACTIVITY CENTER

CAIN PAVILION

CHAPEL

FOOD SVC

CENTRAL KITCHEN

H20 HEATER

LAUNDRY

EDITION ST

SUNSHINE INN

RECREATION

SPEECH/AUDIOLOGY

HRD/SCHOOL

COMMUNITY

RELATIONS

HOUSEKEEPING

UTILITY BLDG

GOLFCART

SHED

LA 6400

LA 6390

LA 6380

LA 5971/

S/A 5972

CHILL H20 #2

TEAM,TV,STORAGE

ORTHOTIC STORAGE

IS/ORTHOTICS

H20 HEATER

SWIMMING POOL

ENCLOSURE

PRINTER

REPAIR

CHILL H20 #3

RECREATION

GARAGE

CONFERENCE

ORTHOTICS

GREENHOUSE

LA 6370

LA 6500

OT/PT CENTER

LA 6510

FLAMMABLE

COTTAGE

COTTAGE 6740

COTTAGE 6750

COTTAGE 6760

BEEHIVE

COTTAGE 6730

TRAINING

LA 6450 S/A

LA 6460 T/A

SHIRLEY'S CINEMA

LA 6480 S/A

ADMINISTRATION

INFIRMARY

FUELING STATION

AB2

AB1

AHJ COMM. 4/25/24

SCALE: 1"=140'-0"

1) All work is new unless otherwise indicated to be All work is new unless otherwise indicated to be "existing" or "reused" or "relocated". 2) Where new work is applicable to patient/client living, Where new work is applicable to patient/client living, use, or support areas; Contractor shall obtain an approved Infection Control Permit prior to initiating actual work. Permit application shall be initiated with his mobilization submittal. (See UGCs/SGCs Article 7.8.) 3) Existing underground utility locations shown are Existing underground utility locations shown are approximate. Contractor shall field verify exact locations prior to excavation or trenching. Contractor shall HAND DIG within 5 feet either side of potential utility conflicts/interferences until the utility is physically exposed prior to performing mechanical trenching or excavating. 4) Contractor shall field verify by measurement exact Contractor shall field verify by measurement exact locations depicted and all dimensions. 5) Prospective bidders are highly encouraged to attend Prospective bidders are highly encouraged to attend the scheduled pre-bid site visit to thoroughly familiarize themselves with any and all existing site and project location conditions which may affect the work under this contract. The Owner and Engineer will not be responsible for Contractor errors or omissions which could be made reasonably known by attending a scheduled site visit. 6) The plans indicate the extent and general requirements The plans indicate the extent and general requirements of the demolition, alterations, relocations, and additions. If any departures from the drawings are deemed necessary by the Contractor, details of such departures and the reasons therefore shall be submitted as soon as possible to the Engineer and Owner for action. No such departures shall be made without prior approval of the Engineer and Owner. 7) Every effort has been made to clearly and fully depict Every effort has been made to clearly and fully depict all known existing conditions and items requiring removal, relocation, demolition and/or alteration. Due to the small scale of the drawings and the nature of renovation and rehab work, certain items such as those concealed behind equipment, finishes, or structural members and the like; or those not accessible for inspection or identifiable as abandoned or to be abandoned without destruction; may not be specifically and/or separately defined or shown. The Contractor shall provide all required removal, relocation, demolition, and/or alteration of such items reasonably inherent with such renovation and rehabilitation work at no additional cost to the Owner in accordance with the best commercial practices and these contract documents to provide a complete and useable facility within the scope of the work to be performed. No consideration shall be given to the nature of the materials, and all demolition shall be designated as unclassified demolition. Demolition of every description and of whatever substances encountered shall be performed to the degree required for the installation of the items/finishes required herein or as specified. 8) Wherever the word(s) "provide", "furnish", "install" Wherever the word(s) "provide", "furnish", "install" and/or the like is/are used; it is to be defined as and understood to require that the Contractor shall provide the item/system(s) totally and completely furnished, installed, and fully operable and useable for its/their intended purpose(s) unless specifically noted otherwise in the contract documents.

NOTES APPLY TO ALL SHEETS

LEGEND

BUILDINGS IN PROJECT GENERATOR NUMBER ALTERNATE BID #1 ALTERNATE BID #2

AB1

EXISTING GENERATOR SHALL BE REMOVED AND REPLACED WITH NEW GENERATOR. NUMBER AS INDICATED. EXISTING GENERATOR SHALL REMAIN. NO WORK UNDER THIS PROJECT. NEW GENERATOR SHALL BE INSTALLED. NUMBER AS INDICATED. EXISTING GENERATOR SHALL BE SALVAGED AND TURNED OVER TO FACILITY AT LOCATION AS DIRECTED BY FACILITY. GENERATORS TO BE SALVAGED: #4, 5, 6, 7, 9 AND 12. EXISTING GENERATOR #12 SHALL BE REMOVED, AND RELOCATED UNDER ADD ALT. #1. BECOMES GEN #17.

AB2

E.0

SHEET INDEX

DESIGN CRITERIA

A. MECHANICAL DESIGN CRITERIA: MECHANICAL DESIGN CRITERIA: 1. DESIGN TEMPERATURE CONDITIONS: DESIGN TEMPERATURE CONDITIONS: A. OUTSIDE OUTSIDE SUMMER 105 F 105°FWINTER 22 F 22°FB. INSIDE INSIDE SUMMER 75 F 75°FWINTER 70 F 70°F2. TYPE OF SYSTEM: TYPE OF SYSTEM: A. HVAC: N/A HVAC: N/A N/A B. VENTILATION: N/A VENTILATION: N/A N/A C. EXHAUST: N/A EXHAUST: N/A N/A D. LIGHTING LOWAD BASIS: N/A LIGHTING LOWAD BASIS: N/A N/A E. AIR: N/A AIR: N/A N/A F. TOTAL COOLING CAPACITY : N/A TOTAL COOLING CAPACITY : N/A : N/A N/A G. TOTAL HEATING CAPACITY: N/A TOTAL HEATING CAPACITY: N/A N/A H. REQUIRED EER: N/A REQUIRED EER: N/A N/A

B. ELECTRICAL DESIGN CRITERIA: ELECTRICAL DESIGN CRITERIA: 1. SYSTEM DESCRIPTION BASED ON EXISTING IN EACH BUILDING. SYSTEM DESCRIPTION BASED ON EXISTING IN EACH BUILDING. A. SERVICE: 208-120V/3 (EXISTING) SERVICE: 208-120V/3 (EXISTING) 208-120V/3 (EXISTING)B. SERVICE: 240V/3 (EXISTING) SERVICE: 240V/3 (EXISTING) 240V/3 (EXISTING)C. SERVICE: 480V/3 (EXISTING) SERVICE: 480V/3 (EXISTING) 480V/3 (EXISTING)C. CODES: CODES: 1. BUILDING CODE: 2012 INTERNATIONAL BUILDING CODE BUILDING CODE: 2012 INTERNATIONAL BUILDING CODE 2012 INTERNATIONAL BUILDING CODE 2. MECHANICAL CODE: 2012 INTERNATIONAL MECHANICAL CODE MECHANICAL CODE: 2012 INTERNATIONAL MECHANICAL CODE 2012 INTERNATIONAL MECHANICAL CODE 3. PLUMBING CODE: 2012 INTERNATIONAL PLUMBING CODE PLUMBING CODE: 2012 INTERNATIONAL PLUMBING CODE 2012 INTERNATIONAL PLUMBING CODE 4. ELECTRICAL CODE: 2011 NATIONAL ELECTRIC CODE ELECTRICAL CODE: 2011 NATIONAL ELECTRIC CODE 2011 NATIONAL ELECTRIC CODE 5. ENERGY CODE: 2012 INTERNATIONAL ENERGY CONSERVATION CODE ENERGY CODE: 2012 INTERNATIONAL ENERGY CONSERVATION CODE 2012 INTERNATIONAL ENERGY CONSERVATION CODE 6. FIRE CODE: 2012 INTERNATIONAL FIRE CODE FIRE CODE: 2012 INTERNATIONAL FIRE CODE 2012 INTERNATIONAL FIRE CODE 7. LIFE SAFETY 2012 LIFE SAFETY CODE LIFE SAFETY 2012 LIFE SAFETY CODE 2012 LIFE SAFETY CODE 8. NFPA 110 2010 EMERGENCY AND STANDBY POWER SYSTEMS NFPA 110 2010 EMERGENCY AND STANDBY POWER SYSTEMS 2010 EMERGENCY AND STANDBY POWER SYSTEMS

Sheet List Table

Sheet Number

Sheet Title

COVER

G.1

GENERAL SITE PLAN

E.0

SHEET INDEX

E.1

SYMBOLS AND GENERAL NOTES

E.2

BUILDING MATRIX EXISTING AND NEW

Sheet List Table

Sheet Number

Sheet Title

ELECTRICAL

E1.01

FLOOR PLAN - BLDG.596 - ELEC - DEMO

E1.02

FLOOR PLAN - BLDG.596 - ELEC.

E2.00

PARTIAL SITE PLAN - GENERATOR

E2.01

FLOOR PLAN - BLDG.633 - ELEC.

E2.02

FLOOR PLAN - BLDG.634 - ELEC.

E2.03

FLOOR PLAN - BLDG.635 - ELEC.

E2.04

FLOOR PLAN - BLDG.636 - ELEC.

E2.05

ONE LINE ELECTRICAL SCHEMATIC DIAGRAM (BLDG. 633,634,635 & 636)

E2.06

ONE LINE ELECTRICAL SCHEMATIC DIAGRAM (BLDG.633, 634, 635 & 636)

E3.00

E3.01

FLOOR PLAN - BLDG.645 - ELEC.

E3.02

FLOOR PLAN - BLDG.646 - ELEC.

E3.03

FLOOR PLAN - BLDG. 648 - ELEC.

E4.00

PARTIAL SITE PLAN - GENERATOR 5 - ELEC.

E4.01

FLOOR PLAN - BLDG. 650 - ELEC.

E4.02

FLOOR PLAN - BLDG.651 - ELEC.

E5.00

E5.01

FLOOR PLAN - BLDG.637 - ELEC.

E5.02

FLOOR PLAN - BLDG.638 - ELEC.

E5.03

FLOOR PLAN - BLDG.639 - ELEC.

E5.04

FLOOR PLAN - BLDG.640 - ELEC.

E5.05

ONE LINE ELECTRICAL SCHEMATIC DIAGRAM (BLDG.637,633,639 AND 640)

E5.06

ONE LINE ELECTRICAL SCHEMATIC DIAGRAM (BLDG.637,633,639 AND 640)

E6.01

FLOOR PLAN - BLDG.597 - ELEC. - DEMO

E6.02

FLOOR PLAN - BLDG.597 - ELEC.

E7.01

FLOOR PLAN - BLDG.652 - ELEC. - DEMO

E7.02

FLOOR PLAN - BLDG.652 - ELEC.

E8.01

FLOOR PLAN - BLDG.659 - ELEC. - DEMO

E8.02

FLOOR PLAN - BLDG.659 - ELEC.

E9.00

E9.01

FLOOR PLAN - BLDG.669 & 670 - ELEC.

E9.02

FLOOR PLAN - BLDG.671 & 672 - ELEC.

E9.03

FLOOR PLAN - BLDG.673 & 674 - ELEC.

E9.04

FLOOR PLAN - BLDG.675 & 676 - ELEC.

E10.01

FLOOR PLAN - BLDG.547 - ELEC.

E11.01

FLOOR PLAN - BLDG.656 - ELEC. - DEMO

E11.02

FLOOR PLAN - BLDG. 656 - ELEC.

E12.01

FLOOR PLAN - BLDG.641 - ELEC. - DEMO

E12.02

FLOOR PLAN - BLDG. 641 - ELEC.

E13.01

FLOOR PLAN - BLDG.665 - ELEC.

E20.01

ELECTRICAL DETAILS

E20.02

ELECTRICAL DETAILS

E20.03

SPECIAL DETAILS

E30.01

E30.02

E30.03

E30.04

PARTIAL SITE PLAN - GENERATOR - BLDG. 664

E31.01

ELECTRICAL SCHEMATIC DIAGRAMS

E31.02

E31.03

E31.04

E31.05

E31.06

E31.07

E40.01

ELECTRICAL SCHEDULES

E40.02

ELECTRICAL SCHEDULES

ELECTRICAL SYMBOLSSTANDARD ABBREVIATIONSGENERAL NOTES (TYPICAL FOR ALL SHEETS)GENERAL NOTES (TYPICAL FOR ALL SHEETS)

E.1

SYMBOLS AND

DUPLEX RECEPTACLE

THREE WAY SWITCH

FOUR WAY SWITCH

KEY SWITCH

DIMMER

PUSH BUTTON

K

3K

THREE WAY KEY SWITCH

WALL SPEAKER

CLOCK OUTLET ONLY

DISCONNECT SWITCH

J

FOUR WAY KEY SWITCH

4K

SWITCH WITH PILOT LIGHT

P

SINGLE RECEPTACLE

SINGLE FACE CLOCK

DOUBLE FACE CLOCK

BELL

BUZZER

HORN

SMOKE DETECTOR

THERMAL DETECTOR

MOTOR CIRCUIT SWITCH

MP

MOTOR

INTERCOM OUTLET

AUDIO VISUAL OUTLET

AUDIO OUTLET

A.F.F.

WP

ABOVE FINISHED FLOOR

WEATHERPROOF

G.F.I.

ALL SYMBOLS SHOWN IN SYMBOL LIST ARE NOT NECESSARILY USED.

I

AV

PHOTOCELL

BLANK PLATE

FLUORESCENT LIGHT FIXTURE LETTER DENOTES TYPE

RECESSED LIGHT FIXTURE LETTER DENOTES TYPE

SURFACE MOUNTED LIGHT FIXTURE, LETTER DENOTES TYPE

WALL MOUNTED LIGHT FIXTURE - LETTER DENOTES TYPE

EXIT LIGHT - ARROW AS INDICATED

LIGHT FIXTURE EQUIPPED WITH EMERGENCY BALLAST

JUNCTION BOX

CONDUIT CONCEALED IN CEILING OR WALL

CONDUIT CONCEALED IN, OR BELOW FLOOR - SEE SPECS

CONDUIT EXPOSED, PARALLEL TO BUILDING LINES

CONDUIT HOMERUN

CONDUIT STUBBED UP

CONDUIT STUBBED DOWN

LIQUID TIGHT FLEXIBLE CONDUIT UNLESS NOTED OTHERWISE

SINGLE POLE SWITCH

TWO POLE SWITCH

SURFACE FLOOR DUPLEX RECEPTACLE

MULTI-OUTLET ASSEMBLY - SEE SPECS

SPECIAL PURPOSE OUTLET

QUADRAPLEX RECEPTACLE

WALL TELEPHONE OUTLET

SURFACE FLOOR DATA/TELEPHONE OUTLET

FLUSH FLOOR DATA/TELEPHONE OUTLET

WALL COMPUTER TERMINAL

SURFACE FLOOR COMPUTER TERMINAL

FLUSH FLOOR COMPUTER TERMINAL

WALL MICROPHONE OUTLET

FLOOR MOUNTED MICROPHONE OUTLET

WALL TELEVISION OUTLET

WALL VOLUME CONTROL

RECESSED CEILING SPEAKER

FIRE ALARM PULL STATION

FIRE ALARM AUDIBLE/VISUAL WARNING DEVICE

FIRE ALARM WARNING BELL (WEATHERPROOF)

FIRE ALARM WARNING LIGHT

SMOKE DETECTOR IN DUCT

MOTOR CIRCUIT SWITCH WITH PILOT LIGHT

MOTOR CONTROLLER OR STARTER

GROUND FAULT INTERRUPTER

FLUSH FLOOR AUDIO OUTLET

EXPLOSION PROOF SEAL

OCCUPANCY SENSOR SWITCH

OS

CEILING FAN

NURSE CALL

LIGHT POLE

FLOOD LIGHT

WALL WASH

TRACK LIGHT

STRIP LIGHT

SC

CEILING MOTION SENSOR

WALL MOTION SENSOR

CAMERA

CAMERA (CEILING MOUNTED)

FC

FAN CONTROL

FLUSH FLOOR DUPLEX RECEPTACLE

DUPLEX GFI RECEPTACLE

DATA / TELEPHONE

COAX

DESCRIPTION

SYMBOL

DESCRIPTION

ABOVE FINISHED FLOOR

AFF

INCLOSURE

INC

ABOVE

ABV

INDICATE

IND

ACOUSTICAL LINING

AL

INSIDE DIAMETER

ID

AIR CONDITIONING

AC

JUNCTION BOX

J-BOX

ALTERNATE

ALT

KILOVOLT-AMPERES

KVA

ALUMINUM

AL

KILOWATT-HOUR

KWH

AMPERE

AMP

KILOWATTS

KW

AMPS

LAVATORY

LAV

ANGLE VAVLE

ANV

LENGTH

LG

ANNUNCIATOR

ANNUN

LIGHT

APPROXIMATE

APPROX

LOCATE

LOC

ARCHITECT

ARCH

MINIMUM CIRCUIT AMPACITY

MCA

ASSEMBLE

ASSEM

MAIN CIRCUIT BREAKER

MCB

AT

MAIN LUGS ONLY

MLO

AUTOMATIC TRANSFER SWTICH

ATS

MAIN DISTRIBUTION PANEL

MDP

AUTOMATIC

AUTO

MAINTENANCE

MAINT

AUTOMATIC AIR VENT

AAV

MANUFACTURE

MFR

AUXILIARY

AUX

MANUFACTURED

MFD

AMPERE INTERRUPTING CAPACITY

AIC

MANUFACTURING

MFG

BALANCE

BAL

MAXIMUM

MAX

BASEMENT

BSMT

MAX. OVERCURR. PROT. DEVICE

MOPD

BELOW

BEL

MECHANICAL

MECH

BETWEEN

BET

METAL

MET

BOTTOM

BOT

MISCELLANEOUS

MISC

BRAKE HORSEPOWER

BHP

MOTOR

MOT

BREAKER

BKR

MOUNTED

MTD

BRITISH THERMAL UNIT

BTU

NATIONAL ELECTRICAL CODE

NEC

BUILDING

BLDG

NTS

BUTTERFLY VALVE

BFU

NUMBER

NO

CAPACITY

CAP

OFFICE

OFF

CAST IRON

CI

ON CENTER

OC

CEILING

CLG

OPPOSITE

OPP

CENTERLINE

CL

OUTSIDE DIAMETER

OD

CIRCUIT

CKT

PIPE ANCHOR

PA

CLEANOUT PLUG

CO

PIPE GUIDE

PG

COMBUSTION

COMB

PLUGGED TEE

PT

CONCENTRIC REDUCER

CR

PLUMBING

PLBG

CONCRETE

CONC

POLE

CONDUIT

POUNDS PER SQ. IN.

PSI

CONNECT

CONN

PREFABRICATED

PREFAB

CONSTRUCTION

CONST

PRESSURE REDUCER VALVE

PRV

CONTRACTOR

CONT

PRESSURE RELIEF VALVE

PV

DEIONIZED WATER

DE

PRESSURE

PRESS

DELTA

Δ

PRESSURE SWITCH

PS

DETAIL

DET

PB

DIAGRAM

DIAG

REINFORCE

REINF

DIAMETER

DIA

REMOVE

REM

DISCHARGE

DISCH

REQUIRED

REQ'D

DISTILLED WATER

DI

REQUIREMENT

REQM'TS

DOWN

DN

RETURN

RET

DRAIN

REVOLUTIONS PER MINUTE

RPM

DRAWING

DWG

ROOM

RM

EACH

SCHEDULE

SCH

ECCENTRIC REDUCER

SCHEMATIC

SCHEM

ELECTRIC WATER COOLER

EWC

SHEET

SHT

ELECTRICAL

ELECT

SINGLE PHASE

ELECTRICAL CONTRACTOR

SINGLE POLE DOUBLE THROW

SPDT

ELEVATION

ELEV

SPECIFICATIONS

SPEC'S

EMERGENCY

EMERG

SQUARE

SQ

ENGINEER

ENGR

STANDARD

STD

EQUIPMENT

EQUIPT

STEEL

STL

EXHAUST

EXH

STRAINER

STR

EXISTING

EXIST

STRUCTURAL

STRUCT

EXPANSION JOINT

EJ

SURFACE

SURF

EXPLOSION PROOF

EXP PRO

SWITCH

SW

EXTERNAL

EXT

SWITCHBOARD

SWBD

FEET

FT

SYM

FINISH

FIN

SYSTEM

SYS

FIRE DEPARTMENT CONNECTION

FDC

TELEPHONE

TELE

FIRE HOSE CABINET

FHC

THERMOMETER

TH

FIRE HOSE RACK

FHR

THICK

THK

FIRE HYDRANT

FH

TRANSFORMER

XFMR

FLOOR

FLR

TYPICAL

TYP

FLOOR CLEANOUT

FCO

UNDERGROUND

UG

FLOW SWITCH

FS

UNION

UN

FULL LOAD AMPS

FLA

VACUUM

VAC

GALVANIZE

GALV

VALVE

VAL

GATE VALVE

GV

VOLTS

GENERATOR

GEN

WALL CLEANOUT

WCO

GLOBE VALVE

GLV

WATT

W

GRADE

GR

WEATHERPROOF

WP

GROUND

GRD

WITH

W/

HEATING

HTG

WITHOUT

W/O

HIGH PRESSURE

HP

Sheet Metal

SM

HORIZONTAL

HORIZ

HORESPOWER

HP

HOSE BIBB

HB

CONSTRUCTION: 1. COMPLETE INSTALLATIONS SHALL CONFORM TO ALL COMPLETE INSTALLATIONS SHALL CONFORM TO ALL APPLICABLE FEDERAL CODES, STATE CODES AND LOCAL ORDINANCES. 2. COMPLETE INSTALLATIONS SHALL CONFORM TO THE COMPLETE INSTALLATIONS SHALL CONFORM TO THE CONTRACT DOCUMENTS, SPECIFICATIONS AND ADDENDUMS ISSUED. IF ANY CONFLICTS OCCUR, THE MOST STRINGENT SHALL APPLY. 3. ALL WORK SHALL BE DONE IN AN ACCEPTABLE ALL WORK SHALL BE DONE IN AN ACCEPTABLE WORKMANSHIP MANNER USING THE MOST CURRENT ACCEPTABLE INDUSTRY STANDARDS. 4. EXISTING UTILITY LAYOUTS SHOWN ARE BASED ON EXISTING UTILITY LAYOUTS SHOWN ARE BASED ON EXISTING ORIGINAL CONSTRUCTION DOCUMENTS AND MAY OR MAY NOT REFLECT THE ACTUAL EXACT LOCATIONS OF ROUTINGS. 5. CONTRACTOR SHALL BE RESPONSIBLE FOR VERIFYING ON CONTRACTOR SHALL BE RESPONSIBLE FOR VERIFYING ON JOBSITE THE ACTUAL ROUTINGS, ELEVATIONS, SIZES, MATERIALS, ETC. ON JOBSITE. 6. ANY ROUTINGS FOR NEW WORK SHALL BE VERIFIED ON ANY ROUTINGS FOR NEW WORK SHALL BE VERIFIED ON JOBSITE WITH EXISTING CONDITIONS PRIOR TO STARTING ANY DEMOLITION OR NEW CONSTRUCTION WORK. 7. CONTRACTOR SHALL FIELD VERIFY ACTUAL CONDITIONS CONTRACTOR SHALL FIELD VERIFY ACTUAL CONDITIONS ON JOBSITE AS ACTUAL CONDITIONS MAY VARY BETWEEN BUILDINGS, AND IT SHALL BE THE CONTRACTOR RESPONSIBILITY TO MAKE MINOR ADJUSTMENTS NECESSARY TO COMPLETE THE INSTALLATION OF THE WORK. IF EXISTING CONDITIONS PROHIBIT WORK, CONTRACTOR SHALL NOTIFY THE A/E FOR REDIRECTION AS REQUIRED. 8. CONTRACTOR SHALL INSTALL ALL EQUIPMENT WITH DO CONTRACTOR SHALL INSTALL ALL EQUIPMENT WITH DO REGARD TO REQUIRED MAINTENANCE ACCESS INCLUDING BUT NOT LIMITED TO PANELS, ELECTRICAL J-BOX CONNECTIONS, CONTROLS, VALVES, COILS, FILTERS, MOTORS, ETC. 9. MOUNT ALL BUILDING ANNUNICATOR PANELS. AT 48" MOUNT ALL BUILDING ANNUNICATOR PANELS. AT 48" ABOVE FINISH FLOOR TO CENTER LINE OR TO OTHER DIMENSIONS AS REQUIRED FOR HANDICAP MOUNTING REQUIREMENTS. 10. CONTRACTOR SHALL FURNISH AND INSTALL ALL CONTRACTOR SHALL FURNISH AND INSTALL ALL NECESSARY TRANSITIONS OFF-SETS FOR PROPER CONNECTIONS. CONTRACTOR SHALL REFER TO MANUFACTURERS EQUIPMENT SUBMITTALS FOR ALL CONNECTION SIZES. 11. DEMOLITION: CONTRACTOR SHALL FULLY COORDINATE ALL DEMOLITION: CONTRACTOR SHALL FULLY COORDINATE ALL CONTRACTOR SHALL FULLY COORDINATE ALL DEMOLITION ON JOBSITE WITH EXISTING CONDITIONS AND OTHER TRADES TO VERIFY EXACTLY WHAT IS BEING REMOVED. REMOVAL OF ANY WORK NOT REQUIRED SHALL BECOME THE CONTRACTOR'S RESPONSIBILITY TO RE-INSTALL AS REQUIRED FOR PROPER OPERATION OF SYSTEMS. 12. SITE SECURITY: CONTRACTOR SHALL BE RESPONSIBLE SITE SECURITY: CONTRACTOR SHALL BE RESPONSIBLE CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING A PORTABLE 8' TALL CHAIN LINK FENCE AROUND THE BUILDING DURING THE TIME THE CONTRACTOR HAS POSSESSION OF THE BUILDING. ALL GATES SHALL BE SECURED WITH A LOCK. A SET OF KEYS FOR CONTRACTOR'S LOCKS HALL BE PROVIDED TO THE FACILITY IN CASE THE FACILITY HAS TO HAVE ACCESS TO THE BUILDING WHEN THE CONTRACTOR IS NOT ON SITE. 13. FIRE PROTECTION: CONTRACTOR SHALL MAINTAIN AND FIRE PROTECTION: CONTRACTOR SHALL MAINTAIN AND CONTRACTOR SHALL MAINTAIN AND MAKE SURE FIRE SPRINKLERS AND FIRE ALARM ARE KEPT IN OPERATION AS MUCH AS POSSIBLE. ANY DOWNTIME OF THESE SYSTEMS SHALL BE FULLY COORDINATED WITH THE FACILITY AND FIRE DEPARTMENT IF REQUIRED. 14. HVAC: CONTRACTOR SHALL MAINTAIN HEATING TO THE HVAC: CONTRACTOR SHALL MAINTAIN HEATING TO THE CONTRACTOR SHALL MAINTAIN HEATING TO THE BUILDING AT ALL TIMES DURING PERIODS OF COLD WEATHER FOR FREEZE PROTECTION. CONTRACTOR SHALL PROVIDE PORTABLE HEATERS TO MAINTAIN A MINIMUM OF 50°F INSIDE THE BUILDING.15. POWER: CONTRACTOR SHALL MAINTAIN BUILDING POWER POWER: CONTRACTOR SHALL MAINTAIN BUILDING POWER CONTRACTOR SHALL MAINTAIN BUILDING POWER UNLESS THE BUILDING MAIN POWER HAS TO BE SHUT OFF. IF BUILDING POWER HAS TO BE SHUT OFF, FACILITY SHALL BE NOTIFIED TWO (2) WEEKS IN ADVANCE OF THE SHUT-DOWN. 16. WATER: WATER USAGE SHALL ONLY BE USED AS WATER: WATER USAGE SHALL ONLY BE USED AS WATER USAGE SHALL ONLY BE USED AS REQUIRED FOR CONSTRUCTION. 17. ALL DEMOLITION MATERIALS SHALL BE PLACED IN A ALL DEMOLITION MATERIALS SHALL BE PLACED IN A DUMPSTER AS REMOVED AND NOT STORED IN THE CONSTRUCTION FENCE AREA UNLESS NECESSARY WHILE WAITING REMOVAL. 18. CONDUITS TO BE REMOVED SHALL BE REMOVED BACK CONDUITS TO BE REMOVED SHALL BE REMOVED BACK TO JOINT, EQUIPMENT CONNECTION, ETC. EXACT POINT OF TERMINATION SHALL BE VERIFIED ON JOBSITE. 19. CONDUIT HANGERS SHALL BE NEW OR IF APPROVED CONDUIT HANGERS SHALL BE NEW OR IF APPROVED THE EXISTING HANGERS CAN BE REUSED. IF REUSED THE CONTRACTOR SHALL CLEAN OFF ANY RUST, PAINTED WITH A RUST INHIBITOR, AND THEN PAINTED WITH COLD GALVANIZED PAINT. 20. ANY MATERIALS THAT HAVE TO BE REMOVED TO MAKE ANY MATERIALS THAT HAVE TO BE REMOVED TO MAKE ROOM FOR NEW EQUIPMENT SHALL BE STORED AND PROTECTED FOR RE-INSTALLATION. ANY MATERIALS DAMAGED SHALL BE REPLACED AT CONTRACTORS EXPENSE. 21. ALL NEW CONTROL CONDUIT SHALL BE SECURELY ALL NEW CONTROL CONDUIT SHALL BE SECURELY MOUNTED AT PROPER INTERVALS TO PREVENT SAGGING. 22. ALL NEW PENETRATIONS LOCATIONS SHALL BE VERIFIED ALL NEW PENETRATIONS LOCATIONS SHALL BE VERIFIED ON JOBSITE WITH EXISTING STRUCTURAL CONDITIONS. 23. ANY ROOF PENETRATIONS SHALL BE COORDINATED WITH ANY ROOF PENETRATIONS SHALL BE COORDINATED WITH FACILITY WITH REGARD TO ANY ROOF WARRANTY THAT MAY BE IN PLACE. IF THE ROOF IS STILL UNDER WARRANTY, ROOF PATCHING SHALL BE AS PER ROOFING MANUFACTURERS RECOMMENDATION AND REQUIREMENTS OR AS INDICATED AND DETAILED. 24. WHEN NEW EQUIPMENT CONCRETE PADS ARE FORMED WHEN NEW EQUIPMENT CONCRETE PADS ARE FORMED AND POURED, CONTRACTOR SHALL ALLOW FOR NOTCHING OF CONCRETE PAD TO MISS ANY EXISTING CONDITIONS. CONTRACTOR SHALL VERIFY REQUIREMENTS ON JOBSITE. 25. CONTROL CONTRACTOR SHALL MAINTAIN BAS CONTROL CONTRACTOR SHALL MAINTAIN BAS COMMUNICATION CAMPUS LOOP DURING PERIODS WHEN BUILDINGS ARE UNDER CONSTRUCTION. 26. CONTRACTOR SHALL COVER AND/OR PROTECT ALL THE CONTRACTOR SHALL COVER AND/OR PROTECT ALL THE EXISTING EQUIPMENT, PANELS, ETC. DURING CONSTRUCTION. 27. ALL CONSTRUCTION OPENINGS SHALL BE CLOSED OFF ALL CONSTRUCTION OPENINGS SHALL BE CLOSED OFF AT THE END OF EACH WORK DAY. 28. ANY "HOT WORK" SHALL BE COORDINATED THRU THE ANY "HOT WORK" SHALL BE COORDINATED THRU THE FACILITY RISK MANAGEMENT GROUP AS REQUIRED FOR PERMITTING. 29. REMOVAL OF ALL EXISTING DETECTORS OR ANY OTHER REMOVAL OF ALL EXISTING DETECTORS OR ANY OTHER DEVICES DIRECTLY CONNECTED TO THE BUILDING FIRE ALARM SYSTEM SHALL BE COORDINATED WITH THE FACILITY TO ADDRESS POINTS SHUTDOWN UNTIL RECONNECTION. 30. ANY NEW EQUIPMENT SHALL BE STORED IN THE ANY NEW EQUIPMENT SHALL BE STORED IN THE CONTRACTOR'S STORAGE AREA AND BE PROTECTED FROM WEATHER CONDITIONS OR STORED IN CONNEX STORAGE CONTAINERS. 31. THE CONTROL CONTRACTOR SHALL BE FULLY THE CONTROL CONTRACTOR SHALL BE FULLY RESPONSIBLE FOR MAINTAINING CONTROLS TO ALL BUILDING THAT ARE NOT INCLUDED IN THIS PROJECT. 32. CONTRACTOR IS RESPONSIBLE FOR VERIFYING EXACT CONTRACTOR IS RESPONSIBLE FOR VERIFYING EXACT LOCATION OF EXISTING UNDERGROUND UTILITIES IN ALL AREAS OF NEW ROUTINGS OF ELECTRICAL CONDUITS, ETC. 33. CONTRACTOR SHALL BE RESPONSIBLE FOR PATCHING CONTRACTOR SHALL BE RESPONSIBLE FOR PATCHING AND REPAIRING ALL AREAS DISTURBED BY INSTALLATION OF ANY UNDERGROUND ELECTRICAL CONDUITS, WIRING, ETC. SEE SHEET E20.03 FOR TYPICAL PATCHING AND INSTALLATION DETAILS FOR CONCRETE, ASPHALT AREAS, ETC. 34. IT IS ACCEPTABLE TO INSTALL NEW UNDERGROUND IT IS ACCEPTABLE TO INSTALL NEW UNDERGROUND CONDUITS, ETC, BY BORING UNDERGROUND IF IT IS MORE ECONOMICAL TO DO SO. 35. ALL SALVAGED GENERATORS SHALL BE REMOVED BY ALL SALVAGED GENERATORS SHALL BE REMOVED BY CONTRACTOR AND TURNED OVER TO OWNER. DELIVER TO LOCATION ON CAMPUS AS DIRECTED BY FACILITY. 36. CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING AND INSTALLING NEW PANEL ID TAGS AND NEW PANEL INDEX SHEET LOGS ON AND IN ALL PANELS INVOLVED ON THIS PROJECT. REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION.

NOTE: THESE NOTES FOR ALL SHEETS. REFER TO EACH SHEETS FOR ADDITIONAL GENERAL NOTES THAT RELATE TO THOSE SHEETS. THESE NOTES FOR ALL SHEETS. REFER TO EACH SHEETS FOR ADDITIONAL GENERAL NOTES THAT RELATE TO THOSE SHEETS.

GENERAL ELECTRICAL NOTES: 1. PROVIDE LABOR MATERIALS, EQUIPMENT AND PROVIDE LABOR MATERIALS, EQUIPMENT AND TRANSPORTATION TO RECEIVE, INSTALL, ADJUST, AND PUT INTO OPERATION COMPLETE ELECTRICAL SYSTEMS IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. PROVIDE PRODUCTS NOT MENTIONED BUT OBVIOUSLY NECESSARY AND INCIDENTAL TO THE COMPLETION OF THIS WORK. 2. ALL WORK DONE SHALL BE PERFORMED BY QUALIFIED ALL WORK DONE SHALL BE PERFORMED BY QUALIFIED ELECTRICIANS, UNDER THE SUPERVISION AND DIRECTION OF A SUPERINTENDENT HAVING SUCCESSFUL EXPERIENCE INSTALLING AND SUPERVISING EQUIPMENT AND SYSTEMS OF SIMILAR TYPE AND SIZE AS INDICATED BY CONTRACT DOCUMENTS. 3. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH CURRENT RULES, REGULATIONS, AND INDUSTRY STANDARDS OF THE NATIONAL ELECTRICAL CODE, UL, NEMA, NFPA, OSHA, NATIONAL ELECTRICAL SAFETY CODE, AND ANY LOCAL CODES, LAWS, OR ORDINANCES. IN THE EVENT THAT A DISCREPANCY IS FOUND IN THE CONTRACT DOCUMENTS, THE ENGINEER SHALL BE NOTIFIED IMMEDIATELY. 4. EXAMINE AND BECOME FAMILIAR WITH ALL CONTRACT EXAMINE AND BECOME FAMILIAR WITH ALL CONTRACT DOCUMENTS IN THEIR ENTIRETY. SURVEY THE PROJECT AND BECOME FAMILIAR WITH CONDITIONS AND SCOPE OF WORK. 5. COORDINATE WORK WITH ALL OTHER TRADES. GIVE COORDINATE WORK WITH ALL OTHER TRADES. GIVE SPECIAL CONSIDERATION TO COORDINATING INSTALLATION. VERIFY EXACT LOCATION, AND FINISH OF DEVICES WITH A/E OR OWNER REPRESENTATIVE PRIOR TO INSTALLATION. 6. ALL PRODUCTS SHALL BE U.L. LISTED AND INSTALLED IN ALL PRODUCTS SHALL BE U.L. LISTED AND INSTALLED IN ACCORDANCE WITH NATIONALLY RECOGNIZED AND ACCEPTED STANDARDS AND PROCEDURES. 7. ALL ELECTRICAL DISTRIBUTION EQUIPMENT, TRANSFORMERS, ALL ELECTRICAL DISTRIBUTION EQUIPMENT, TRANSFORMERS, PANELBOARDS, AND OTHER ENCLOSED EQUIPMENT SHALL BE IDENTIFIED AS INDICATED ON THE CONTRACT DRAWINGS. SAID IDENTIFICATION SHALL CONSIST OF PERMANENTLY ATTACHED ENGRAVED LAMINATED PLASTIC NAMEPLATES. EACH BRANCH CIRCUIT OVERCURRENT PROTECTION DEVICE SHALL BE IDENTIFIED BY CIRCUIT NUMBER. EACH BRANCH CIRCUIT SPLICE OR TERMINATION SHALL BE IDENTIFIED BY PANEL AND CIRCUIT DESIGNATION SHOWN ON THE JUNCTION OR OUTLET BOX, OR UPON INDIVIDUAL WIRES IN CASES WHERE MORE THAN ONE OF EACH PHASE CONDUCTOR OCCURS. 8. REFERENCE ELECTRICAL SPECIFICATIONS FOR DEVICES, REFERENCE ELECTRICAL SPECIFICATIONS FOR DEVICES, MATERIALS AND WORKMANSHIP REQUIREMENTS NOT SPECIFIED ON THESE DRAWINGS. 9. "RECORD" DRAWINGS SHALL INCLUDE ALL BRANCH CIRCUIT "RECORD" DRAWINGS SHALL INCLUDE ALL BRANCH CIRCUIT WORK, ANY PANELBOARD INFORMATION AVAILABLE, FINAL SWITCHING, ETC. 10. ELECTRONIC COPIES WILL BE ACCEPTABLE IN LIEU OF ELECTRONIC COPIES WILL BE ACCEPTABLE IN LIEU OF "HARD COPIES". 11. ELECTRICAL PLAN DRAWINGS ARE DIAGRAMMATIC; ELECTRICAL PLAN DRAWINGS ARE DIAGRAMMATIC; THEREFORE, DO NOT SCALE FROM THESE DRAWINGS. 12. REFER TO DRAWINGS FOR GUIDANCE AND VERIFICATION OF REFER TO DRAWINGS FOR GUIDANCE AND VERIFICATION OF DIMENSIONS. 13. INSTALL LIGHTING FIXTURES AS INDICATED ON ELECTRICAL INSTALL LIGHTING FIXTURES AS INDICATED ON ELECTRICAL PLANS. 14. PENETRATIONS OF WALLS, FLOORS AND ROOF FOR THE PENETRATIONS OF WALLS, FLOORS AND ROOF FOR THE PASSAGE OF ELECTRICAL RACEWAYS TO BE APPROVED. ALL SUCH PENETRATIONS TO BE PROPERLY SEALED AFTER INSTALLATION OF RACEWAYS SO AS TO MAINTAIN THE STRUCTURAL, WATERPROOF AND FIREPROOF INTEGRITY OF THE WALL, FLOOR OR ROOF SYSTEM TO BE PENETRATED. 15. CONNECT EMERGENCY LIGHTS AS INDICATED. CONNECT EMERGENCY LIGHTS AS INDICATED. 16. ALL EQUIPMENT REQUIRING STARTERS OR COMBO ALL EQUIPMENT REQUIRING STARTERS OR COMBO STARTER/ DISCONNECTS SHALL BE PROVIDED AS COORDINATED. 17. ALL CONDUCTORS ARE TO BE COPPER U.N.O. ALL CONDUCTORS ARE TO BE COPPER U.N.O. 18. CONDUCTORS, RACEWAYS AND CABLES, IN EXPOSED AND CONDUCTORS, RACEWAYS AND CABLES, IN EXPOSED AND CONCEALED LOCATIONS, MUST BE PROTECTED AGAINST PHYSICAL DAMAGE. 19. MAINTAIN DEDICATED WORKING SPACE CLEARANCE FOR MAINTAIN DEDICATED WORKING SPACE CLEARANCE FOR ELECTRICAL EQUIPMENT, PER NEC 110.26.

LIGHTING: 1. ALL HOME RUNS SHOWN ARE (2) #12 & #12 GND ALL HOME RUNS SHOWN ARE (2) #12 & #12 GND IN 1/2" C. UNLESS OTHERWISE NOTED. HOME RUNS OVER 100 FT IN LENGTH TO THE LAST FIXTURE SHALL BE (2) #10 & #12 GND IN 1/2" C. 2. REFERENCE ELECTRICAL DETAIL SHEET(S) FOR REFERENCE ELECTRICAL DETAIL SHEET(S) FOR SCHEDULES, ELECTRICAL SYMBOLS, ETC.

SPECIAL SYSTEM/FIRE ALARM GENERAL NOTES: 1. INSTALLATION SHALL CONFORM TO ALL REQUIREMENTS OF INSTALLATION SHALL CONFORM TO ALL REQUIREMENTS OF APPLICABLE ELECTRICAL CODES. 2. WIRING METHODS AND MATERIALS SHALL CONFORM WITH WIRING METHODS AND MATERIALS SHALL CONFORM WITH ALL APPLICABLE SECTION OF NEC 760. 3. 120 VAC @ 60Hz INPUT POWER SHALL BE INSTALLED BY 120 VAC @ 60Hz INPUT POWER SHALL BE INSTALLED BY LICENSE ELECTRICAL CONTRACTOR. 4. ALL SLEEVES AND PENETRATION AND FIRE CAULKING ALL SLEEVES AND PENETRATION AND FIRE CAULKING SHALL BE PROVIDED BY ELECTRICAL CONTRACTOR. 5. DEDICATED LOCKING BREAKER PROPERLY LABELED DEDICATED LOCKING BREAKER PROPERLY LABELED SOURCE SHALL SUPPLY FIRE ALARM CONTROL(S). 6. 120 VAC IS NOT PERMITTED IN THE SAME RACEWAY AS 120 VAC IS NOT PERMITTED IN THE SAME RACEWAY AS LOW VOLTAGE WIRING. 7. FIRE ALARM CONTRACTOR SHALL REFER TO ELECTRICAL FIRE ALARM CONTRACTOR SHALL REFER TO ELECTRICAL SHEETS AND MECHANICAL FOR EXTENT OF FIRE ALARM WORK. 8. THE EXISTING FIRE ALARM SYSTEM SHALL REMAIN. ANY THE EXISTING FIRE ALARM SYSTEM SHALL REMAIN. ANY NEW DEVICES ETC. SHALL BE MATCHING DEVICES TO FULLY INTEGRATE WITH THE EXISTING SYSTEM. 9. THE EXISTING FIRE ALARM ANNUNCIATOR PANEL SHALL BE THE EXISTING FIRE ALARM ANNUNCIATOR PANEL SHALL BE REMOVED IN EACH BUILDING INVOLVED WITH THIS PROJECT AND REPLACED WITH NEW ANNUNICATOR PANEL AND WIRING. 10. ALL INITIATING CIRCUIT SHALL BE CLASS "A" WIRING WITH ALL INITIATING CIRCUIT SHALL BE CLASS "A" WIRING WITH A MINIMUM OF (6) SIX FOOT SEPARATION.

NOTE: THESE NOTES FOR ALL SHEETS. REFER TO EACH SHEETS FOR ADDITIONAL GENERAL NOTES THAT RELATE TO THOSE SHEETS. THESE NOTES FOR ALL SHEETS. REFER TO EACH SHEETS FOR ADDITIONAL GENERAL NOTES THAT RELATE TO THOSE SHEETS.

POWER: 1. ALL HOME RUNS SHOWN ARE (2) #12 & #12 GND ALL HOME RUNS SHOWN ARE (2) #12 & #12 GND IN 1/2" C. UNLESS OTHERWISE NOTED. HOME RUNS OVER 100 FT IN LENGTH TO THE LAST FIXTURE SHALL BE (2) #10 & #12 GND IN 1/2" C. 2. REFERENCE ELECTRICAL DETAIL SHEET(S) FOR REFERENCE ELECTRICAL DETAIL SHEET(S) FOR PANELBOARD SCHEDULES, ELECTRICAL RISER DIAGRAM, SYMBOLS, ETC.

CONNECT TO EXISTING

NORMAL POWER

EMERGENCY POWER

NP

E.2

BUILDING MATRIX

EXISTING AND NEW

SEE SHEET E40.02 FOR GENERATOR SCHEDULE

NOTE::

E1.01

FLOOR PLAN -

BLDG.596 - ELEC -

DEMO1 FLOOR PLAN - BLDG.596 - ELEC - DEMO

BUILDING 596

GENERATOR #1

145A

P101

P102

P104

P103

123A

147A

158A

UE

16'

32'

48'

1/16" = 1'-0"

SCALE IN FEET

SCALE: 1/16" = 1'-0"

EXISTING MECHANICAL BUILDING. EXISTING AUTOMATIC TRANSFER SWITCH SHALL BE REMOVED AND TURNED OVER TO OWNER. EXISTING ELECTRIC PANEL "MDP", 120V/280V, 3 , 500A, FED FROMOVERHEAD EXISTING WATER COOLING TOWER. EXISTING PANEL 2, 120/208V/3 , 400A,FED FROM UNDERGROUND EXISTING MECHANICAL ROOM. EXISTING GEN. #1 SHALL BE DISCONNECTED AND REMOVED. EXISTING PANEL E, EMERGENCY PANEL, 120V/208V, 3 , 150AEXISTING UNDERGROUND EMERGENCY POWER FEED SHALL BE ABANDONED. SEE DETAIL 1, SHEET E31.01 FOR ELECTRICAL SCHEMATIC DIAGRAM EXISTING POWER POLE EXISTING EMERGENCY PANEL E1A, 120/208/3 , 100A SHALL REMAIN ANDBE REUSED. EXISTING KITCHEN PANEL SERVICE FEED SHALL REMAIN EXISTING UNDERGROUND ELECTRICAL SERVICE SHALL BE ABANDONED EXISTING OVERHEAD ELECTRICAL SERVICE SHALL BE REWORKED AS REQUIRED. SEE POWER CO.

1. CONTRACTOR SHALL VERIFY ALL EXISTING CONTRACTOR SHALL VERIFY ALL EXISTING CONNECTIONS AND EXACT LOCATION OF EQUIPMENT ON JOBSITE. 2. CONTRACTOR SHALL VISIT JOBSITE AND CONTRACTOR SHALL VISIT JOBSITE AND VERIFY EXTENT OF DEMOLITION BEFORE BIDDING. 3. VERIFY DEMO/SALVAGE OF ALL EXISTING VERIFY DEMO/SALVAGE OF ALL EXISTING ITEM TO BE REMOVED WITH OWNER. 4. FINAL CONNECTION TO ALL ROTATING AND FINAL CONNECTION TO ALL ROTATING AND VIBRATING EQUIPMENT SHALL BE MADE WITH LIQUID - TIGHT FLEXIBLE CONDUIT. 5. ALL EXISTING EQUIPMENT SHOWN CROSS ALL EXISTING EQUIPMENT SHOWN CROSS HATCHED SHALL BE REMOVED UNLESS INDICATED OTHERWISE. 6. ALL EXISTING EQUIPMENT DISCONNECTS ALL EXISTING EQUIPMENT DISCONNECTS SHALL BE REMOVED, ON EQUIPMENT BEING REMOVED.

E1.02

BLDG.596 - ELEC.1 FLOOR PLAN - BLDG.596 - ELEC.

BUILDING 596

GENERATOR #1

145A

123A

147A

158A

ANN

32'

48'

1/16" = 1'-0"

SCALE: 1/16" = 1'-0"

EXISTING MECH. BUILDING. NEW ATS #596-1 MOUNTED ON EXISTING MOUNTED ON EXISTING WALL NEW GENERATOR #1 SET ON NEW SET ON NEW GENERATOR PAD, 200KW, 208V, 3 EXISTING MDP PANEL 2, 120/208V/3 , 400AEXISTING PANEL "MDP", 120/208V/3 , 500A.NEW GENERATOR PAD. SIZE TO FIT GENERATOR AND DOCKING STATION. SEE DETAIL 4, SHEET E20.02. NEW UNDERGROUND EMERGENCY FEEDER CIRCUIT 2-4"C. WITH 4-600 KCMIL AND 1 #1/0 GRD. IN EACH. NEW NORMAL POWER FEED FROM ATS TO MDP. 2-4"C. WITH 4-600 KCMIL AND 1 #1/0 GRD. IN EACH. REFER TO SHEET E20.01 FOR TYPICAL GENERATOR INSTALLATION DETAILS, SCHEMATIC, ETC. EXISTING OVERHEAD PRIMARY SERVICE ON ROOF. VERIFY REQUIREMENTS WITH POWER CO. NEW PRIMARY SERVICE, 2-3 1/2"C. WITH 4-350 KCMIL AND 1 #1 GRD. IN EACH. NEW SAFETY DISCONNECT (WP) 1000A, (WP) 1000A, 208V/3 , NEMA 3R.SHEET E31.01 FOR SCHEMATIC DIAGRAM NEW DOCKING STATION (DUAL PURPOSE)- 208V/3 TO MATCH NEW GENERATOR.EXISTING CRITICAL C-596 PANEL, 120V/208V/3 , 150ASEE DETAIL 1, SHEET E31.01 FOR ONE-LINE SCHEMATIC DIAGRAM. NEW FEED TO NEW LIFE SAFETY PANEL LS-596, 2 #1 AND 1 #6 GRD. IN 1 1/2"C. FURNISH AND INSTALL NEW 6' HIGH CHAIN LINK FENCE WITH 4'-0" GATE REMOVE EXISTING EMERGENCY REMOTE STOP BUTTON AND INSTALL NEW STOP BUTTON. FURNISH AND INSTALL NEW CONDUIT AND WIRING AS REQUIRED. MOUNT ON OUTSIDE OF BUILDING. FURNISH AND INSTALL NE ANNUNICATOR PANEL WITH NEW WIRING AND CONDUIT. VERIFY LOCATION ON JOBSITE. REMOVE OLD ANNUNICATOR PANEL, VERIFY LOCATION. EXISTING EMERGENCY PANEL SHALL BE MODIFIED TO BE NEW LIFE SAFETY PANEL LS-596.

1. CONTRACTOR SHALL VERIFY ALL EXISTING CONTRACTOR SHALL VERIFY ALL EXISTING CONNECTIONS AND EXACT LOCATION OF EQUIPMENT ON JOBSITE. 2. CONTRACTOR SHALL VISIT JOBSITE AND CONTRACTOR SHALL VISIT JOBSITE AND VERIFY EXTENT OF DEMOLITION BEFORE BIDDING. 3. VERIFY DEMO/SALVAGE OF ALL EXISTING VERIFY DEMO/SALVAGE OF ALL EXISTING ITEM TO BE REMOVED WITH OWNER. 4. FINAL CONNECTION TO ALL ROTATING AND FINAL CONNECTION TO ALL ROTATING AND VIBRATING EQUIPMENT SHALL BE MADE WITH LIQUID - TIGHT FLEXIBLE CONDUIT.

ADM 7/15/24

PARTIAL SITE PLAN -

GENERATOR

1 PARTIAL SITE PLAN - GENERATOR #3 - ELECT.

GENERATOR #3

E2.00

BLDG. 636 SEE SHEET E2.04

BLDG. 635 SEE SHEET E2.03

BLDG. 634 SEE SHEET E2.02

BLDG. 633 SEE SHEET E2.01

OE

BLDG. 666

SCALE: 1/32" = 1'-0"

SCALE: AS NOTED

1. CONTRACTOR SHALL VERIFY ALL EXISTING CONTRACTOR SHALL VERIFY ALL EXISTING CONNECTIONS AND EXACT LOCATION OF EQUIPMENT ON JOBSITE. 2. CONTRACTOR SHALL VISIT JOBSITE AND CONTRACTOR SHALL VISIT JOBSITE AND VERIFY EXTENT OF DEMOLITION BEFORE BIDDING. 3. VERIFY DEMO/SALVAGE OF ALL EXISTING VERIFY DEMO/SALVAGE OF ALL EXISTING ITEM TO BE REMOVED WITH OWNER. 4. FINAL CONNECTION TO ALL ROTATING AND FINAL CONNECTION TO ALL ROTATING AND VIBRATING EQUIPMENT SHALL BE MADE WITH LIQUID - TIGHT FLEXIBLE CONDUIT.

EXISTING GENERATOR SHALL BE REMOVED AND NEW GEN. #3 (600 KW) 480V/3 NEW GEN. #3 (600 KW) 480V/3 (600 KW) 480V/3 SHALL BE INSTALLED. SET ON EXISTING CONCRETE PAD. SEE SHEET E30.01. EXISTING EMERGENCY LIGHT POLE SHALL REMAIN. EXISTING OVERHEAD ELECTRIC POWER LINE. NEW UNDERGROUND FEEDER CIRCUIT. 2-4"C. WITH 4-600 KCMIL AND 1 #1/0 GRD. IN EACH. EXISTING DISTRIBUTION PANEL #MDP-1-90 SHALL BE REMOVED EXISTING POWER POLE. EXISTING POLE MOUNTED XFMR #29, #30, #31 ON POLE #13. EXISTING UNDERGROUND BUILDING POWER SERVICE FEEDER FROM EXISTING TRANSFORMER SHALL BE ABANDONED. EXISTING SERVICE ENTRY J-BOX'S. REMOVE AND REPLACE FOR NEW SERVICE J-BOX, SERVICE RATED (WP) EXISTING ATS SHALL BE REMOVED AND TURNED OVER TO OWNER EXISTING BUILDING EMERGENCY DISTRIBUTION PANEL. SHALL BE REMOVED AND TURNED OVER TO OWNER. EXISTING CHAIN LINK FENCE ENCLOSURE SHALL BE REMOVED FOR ACCESS THEN RE-INSTALLED. SEE LARGE SCALE PARTIAL SITE PLAN SHEET E30.01, DETAIL 1 FOR WORK IN THIS AREA. EXISTING UNDERGROUND NORMAL POWER FEED TO EXISTING ATS. 3 #1/0, 1 #6G, 1 1/2"C., 208V/3 TO BE ABANDONEDNEW SAFETY DISCONNECT (WP) 800A, 208V/3 , SERVICE RATEDSEE SHEET E2.05 AND E2.06 FOR ONE LINE SCHEMATIC. EXISTING ELECTRICAL DISTRIBUTION TRANS-CLOSER, SEE SHEET E2.02 FOR WORK IN THIS AREA. NEW ATS #633-1, MOUNTED ON , MOUNTED ON CONCRETE PAD. NEW ATS #634-1, MOUNTED ON , MOUNTED ON CONCRETE PAD. NEW ATS #635-1, MOUNTED ON , MOUNTED ON CONCRETE PAD. NEW ATS #636-1, MOUNTED ON , MOUNTED ON CONCRETE PAD. SEE DETAIL 1, SHEET E30.01 FOR CONTINUATION.

E2.01

BLDG.633 - ELEC.

1 FLOOR PLAN - BLDG.633 - ELEC.

BUILDING 633

EXISTING NORMAL POWER SHALL BE ABANDONED

NURSES STATION

ATS #633-1

8'

24'

1/8" = 1'-0"

SCALE: 1/8" = 1'-0"

EXISTING PANEL "MDP". 120/208V-3 , 200ASHALL BE REMOVED, AND NEW PANEL MDP-633 INSTALLED. EXISTING ANNUNICATOR PANEL SHALL BE REMOVED AND REPLACED WITH NEW ANNUNICATOR PANEL. VERIFY EXACT MOUNTING LOCATION ON JOBSITE EXISTING PANEL "L", 225A, 120/208V/3 EXISTING PANEL "E", 225A, 120/208V/3 NEW ELECT. J-BOXES (WP) SERVICE RATED EXISTING UNDERGROUND EMERGENCY POWER CIRCUIT SHALL BE ABANDONED. NEW 4" FEEDER CONDUITS, REMOVE EXISTING CONDUITS AS REQUIRED TO INSTALL NEW FEEDER CONDUITS. NEW SAFETY DISCONNECT (WP) 800A, 208V/3 ,NEMA 3R, WP SEE SHEET E2.05 AND E2.06 FOR ONE LINE SCHEMATIC DIAGRAM. EXISTING PANEL "H", 400A, 120/208V/3 EXISTING DISCONNECT SWITCH FOR EXISTING KITCHEN PANEL "K", 120/208V/3 , 225A.NEW SERVICE FEED TO ELECTRICAL PANELS. SEE SHEET E2.05 AND E2.06. EXISTING PANEL A-90 (K), 120/208V,3 , 225A(KITCHEN) NEW AUTOMATIC TRANSFER SWITCH (ATS) ATS #633-1, 208V/3 , 208V/3 2-4"C. WITH 4-600 KCMIL AND 1 #1/0 GROUND IN EACH. SEE SHEET E2.00 FOR CONTINUATION. NEW LIFE SAFETY PANEL "LS-633" 120/208V/3 , 150A. MOUNTED ON WALL. VERIFYLOCATION ON JOBSITE.

1. CONTRACTOR SHALL VERIFY ALL EXISTING CONTRACTOR SHALL VERIFY ALL EXISTING CONDITIONS, CONNECTIONS AND EXACT LOCATION OF EQUIPMENT ON JOBSITE. 2. CONTRACTOR SHALL VISIT JOBSITE AND CONTRACTOR SHALL VISIT JOBSITE AND VERIFY EXTENT OF DEMOLITION BEFORE BIDDING. 3. VERIFY DEMO/SALVAGE OF ALL EXISTING VERIFY DEMO/SALVAGE OF ALL EXISTING ITEM TO BE REMOVED WITH OWNER. 4. FINAL CONNECTION TO ALL ROTATING AND FINAL CONNECTION TO ALL ROTATING AND VIBRATING EQUIPMENT SHALL BE MADE WITH LIQUID - TIGHT FLEXIBLE CONDUIT.

E2.02

BLDG.634 - ELEC.

1 FLOOR PLAN - BLDG.634 - ELEC.

BUILDING 634

EXISTING NORMAL POWER

ATS #634-1

EXISTING PANEL "MDP". 120/208V-3 , 200ASHALL BE REMOVED, AND NEW PANEL MDP-634 INSTALLED. EXISTING ANNUNICATOR PANEL SHALL BE REMOVED AND REPLACED WITH NEW ANNUNICATOR PANEL. VERIFY EXACT MOUNTING LOCATION ON JOBSITE. EXISTING PANEL "E", 225A, 120/208V/3 EXISTING ELECT. J-BOXES (WP), SERVICE RATED EXISTING UNDERGROUND EMERGENCY POWER CIRCUIT SHALL BE ABANDONED. NEW 4" FEEDER CONDUITS, REMOVE EXISTING CONDUITS AS REQUIRED TO INSTALL NEW FEEDER CONDUITS. NEW SAFETY DISCONNECT (WP) 800A, 208V/3 ,SERVICE RATED. SEE SHEET E2.05 AND E2.06 FOR ONE LINE SCHEMATIC DIAGRAM EXISTING ELECTRICAL DISTRIBUTION TRANS-CLOSER. EXISTING DISTRIBUTION PANEL #MDP-1-90 SHALL BE REMOVED. NEW AUTOMATIC TRANSFER SWITCH (ATS) ATS #634-1, 208V/3 , 208V/3 EXISTING PANEL "H", 400A, 120/208V/3 NEW SERVICE FEED TO ELECTRICAL PANELS. SEE SHEET E2.05 AND E2.06 EXISTING PANEL "B", 120/208V/3 , 225AEXISTING DISTRIBUTION PANEL #1, 120/208V/3 ,1000A EXISTING PAD MOUNTED TRANSFORMER #2 2-4"C. WITH 4-600 KCMIL AND 1 #1/0 GRD. IN EACH SEE SHEET E2.00 FOR CONTINUATION NEW LIFE SAFETY PANEL "LS-634". . 120/208V/3 , 150A. MOUNTED ON WALL. VERIFYLOCATION ON JOBSITE.

1. CONTRACTOR SHALL VERIFY ALL EXISTING CONTRACTOR SHALL VERIFY ALL EXISTING CONDITIONS, CONNECTIONS AND EXACT LOCATION OF EQUIPMENT ON JOBSITE. 2. CONTRACTOR SHALL VISIT JOBSITE AND CONTRACTOR SHALL VISIT JOBSITE AND VERIFY EXTENT OF DEMOLITION BEFORE BIDDING. 3. VERIFY DEMO/SALVAGE OF ALL EXISTING VERIFY DEMO/SALVAGE OF ALL EXISTING ITEM TO BE REMOVED WITH OWNER. 4. FINAL CONNECTION TO ALL ROTATING AND FINAL CONNECTION TO ALL ROTATING AND VIBRATING EQUIPMENT SHALL BE MADE WITH LIQUID - TIGHT FLEXIBLE CONDUIT.

E2.03

BLDG.635 - ELEC.

1 FLOOR PLAN - BLDG.635 - ELEC.

BUILDING 635

EXISTING NORMAL POWER SHALL BE ABANDONED

ATS #635-1

EXISTING PANEL "MDP", 120/208V/3 , 200ASHALL BE REMOVED AND NEW PANEL MDP-635 INSTALLED. EXISTING ANNUNICATOR PANEL SHALL BE REMOVED AND REPLACED WITH NEW ANNUNICATOR PANEL. VERIFY EXACT MOUNTING LOCATION ON JOBSITE. EXISTING PANEL "L", 225A, 120/208V/3 EXISTING PANEL "E", 225A, 120/208V/3 NEW ELECT. J-BOXES (WP), SERVICE RATED EXISTING UNDERGROUND EMERGENCY POWER CIRCUIT SHALL BE ABANDONED. NEW 4" FEEDER CONDUITS, REMOVE EXISTING CONDUITS AS REQUIRED TO INSTALL NEW FEEDER CONDUITS. NEW SAFETY DISCONNECT (WP) 800A, 208V/3 ,SERVICE RATED, NEMA 3R. SEE SHEET E2.05 AND E2.06 FOR ONE LINE SCHEMATIC DIAGRAM EXISTING PANEL "H", 400A, 120/208V/3 NEW SERVICE FEED TO ELECTRICAL PANELS. SEE SHEET E2.05 AND E2.06. EXISTING PANEL A-90 "K", 120/208V,3 , 225A(KITCHEN) NEW AUTOMATIC TRANSFER SWITCH (ATS) ATS #635-1, 208V/3 , 208V/3 EXISTING DISCONNECT SWITCH FOR EXISTING KITCHEN PANEL "K", 120/208V/3 , 225A.2-4"C. WITH 4-600 KCMIL AND 1 #1/0 GROUND IN EACH SEE SHEET E2.00 FOR CONTINUATION. NEW LIFE SAFETY PANEL "LS-635". . 120/208V/3 , 150A. MOUNTED ON WALL. VERIFYLOCATION ON JOBSITE.

1. CONTRACTOR SHALL VERIFY ALL EXISTING CONTRACTOR SHALL VERIFY ALL EXISTING CONDITIONS, CONNECTIONS AND EXACT LOCATION OF EQUIPMENT ON JOBSITE. 2. CONTRACTOR SHALL VISIT JOBSITE AND CONTRACTOR SHALL VISIT JOBSITE AND VERIFY EXTENT OF DEMOLITION BEFORE BIDDING. 3. VERIFY DEMO/SALVAGE OF ALL EXISTING VERIFY DEMO/SALVAGE OF ALL EXISTING ITEM TO BE REMOVED WITH OWNER. 4. FINAL CONNECTION TO ALL ROTATING AND FINAL CONNECTION TO ALL ROTATING AND VIBRATING EQUIPMENT SHALL BE MADE WITH LIQUID - TIGHT FLEXIBLE CONDUIT.

E2.04

BLDG.636 - ELEC.

1 FLOOR PLAN - BLDG.636 - ELEC.

BUILDING 636

EXISTING UNDERGROUND NORMAL POWER SHALL BE ABANDONED

ATS #636-1

EXISTING PANEL "MDP". 120/208V-3 , 200A,SHALL BE REMOVED, AND NEW PANEL MDP-636 INSTALLED. EXISTING ANNUNICATOR PANEL SHALL BE REMOVED AND REPLACED WITH NEW ANNUNICATOR PANEL. VERIFY EXACT MOUNTING LOCATION ON JOBSITE. EXISTING PANEL "E", 225A, 120/208V/3 NEW ELECT. J-BOXES (WP), SERVICE RATED EXISTING UNDERGROUND EMERGENCY POWER CIRCUIT SHALL BE ABANDONED. NEW 4" FEEDER CONDUITS, REMOVE EXISTING CONDUITS AS REQUIRED TO INSTALL NEW FEEDER CONDUITS. NEW SAFETY DISCONNECT (WP) 800A, 208V/3 ,SERVICE RATED. SEE SHEET E2.05 AND E2.06 FOR ONE LINE SCHEMATIC DIAGRAM. EXISTING PANEL "H", 400A, 120/208V/3 NEW AUTOMATIC TRANSFER SWITCH )ATS) ATS #636-1, 208V/3 , 208V/3 NEW SERVICE FEED TO ELECTRICAL PANELS. SEE SHEET E2.05 AND E2.06. 2-4"C. WITH 4-600 KCMIL AND 1 #1/0 GRD. IN EACH. SEE SHEET E2.00 FOR CONTINUATION EXISTING PANEL "L", 120/208V/3 , 225ANEW LIFE SAFETY PANEL "LS-636". 120/208V/3 , 150A. MOUNTED ON WALL. VERIFYLOCATION JOBSITE.

1. CONTRACTOR SHALL VERIFY ALL EXISTING CONTRACTOR SHALL VERIFY ALL EXISTING CONDITIONS, CONNECTIONS AND EXACT LOCATION OF EQUIPMENT ON JOBSITE. 2. CONTRACTOR SHALL VISIT JOBSITE AND CONTRACTOR SHALL VISIT JOBSITE AND VERIFY EXTENT OF DEMOLITION BEFORE BIDDING. 3. VERIFY DEMO/SALVAGE OF ALL EXISTING VERIFY DEMO/SALVAGE OF ALL EXISTING ITEM TO BE REMOVED WITH OWNER. 4. FINAL CONNECTION TO ALL ROTATING AND FINAL CONNECTION TO ALL ROTATING AND VIBRATING EQUIPMENT SHALL BE MADE WITH LIQUID - TIGHT FLEXIBLE CONDUIT.

E2.05

ONE LINE ELECTRICAL SCHEMATIC DIAGRAM - GENERATOR #3

(BLDG. 633, 634, 635, AND 636) - DEMOLITION

ONE LINE ELECTRICAL

SCHEMATIC DIAGRAM -

GENERATOR #3 (BLDG.

633, 634, 635, AND 636) -

DEMOLITION

NOTES BY SYMBOLGENERAL NOTES

EXISTING TRANSFORMER #2

EXISTING DIST. PANEL #1 120/208V/3 1000A

BUILDING #633

225A

EXISTING DIST. PANEL "MDP" MDP-1-90 120/208V/3 800A

BUILDING #634

EXIST. PANEL "MDP" 200A

EXIST. PANEL "E" 225A

EXIST. PANEL "L" 225A

EXISTING GEN. #3

EXIST. "ATS"

EXIST. PANEL "H" 400A

EXISTING FEEDER 1

EXISTING FEEDER 2

EXISTING EMERGENCY FEEDERS

EXIST. PANEL "K" 225A

DISC. 225A

BUILDING #635

EXIST. PANEL "K" 225A

DISC. 225A

BUILDING #636

EXISTING GENERATOR #3 SHALL BE REMOVED. EXISTING AUTOMATIC TRANSFER SWITCH "ATS" SHALL BE REMOVED. EXISTING GENERATOR SERVICE FEED SHALL BE REMOVED. EXISTING DISTRIBUTION PANEL #1, SHALL BE ABANDONED. EXISTING DISTRIBUTION PANEL "MDP-1-90" SHALL BE REMOVED. EXISTING CONDUCTORS AND CONDUITS SHALL BE ABANDONED. EXISTING TRANSFORMER #2 SHALL REMAIN. EXISTING MDP PANEL SHALL BE REMOVED. CAP EXISTING SERVICE FEEDER CONDUIT. SEAL WATER TIGHT. VERIFY SIZE ON JOBSITE. CAP BELOW GRADE OR INSIDE ELECTRIC ROOM. LABEL ABANDONED. NOT USED EXISTING DISCONNECT SWITCH FOR KITCHEN PANEL "K". 120/208V/3 , 225AEXISTING SERVICE FEEDER SHALL BE REMOVED. EXISTING ELECTRICAL SERVICE FEED FROM SEPERATE TRANSFORMER. VERIFY ON JOBSITE.

1. CONTRACTOR SHALL VERIFY ALL EXISTING CONTRACTOR SHALL VERIFY ALL EXISTING CONNECTIONS, CONDITIONS AND EXACT LOCATIONS OF ALL EXISTING EQUIPMENT ON JOBSITE. 2. CONTRACTOR SHALL VISIT JOBSITE AND CONTRACTOR SHALL VISIT JOBSITE AND VERIFY EXTENT OF DEMOLITION BEFORE BIDDING.

E2.06

ONE LINE ELECTRICAL SCHEMATIC DIAGRAM - GENERATOR #3

(BLDG. 633, 634, 635, AND 636) - NEW WORK

ONE LINE ELECTRICAL

SCHEMATIC DIAGRAM -

GENERATOR #3 (BLDG.

633, 634, 635, AND 636) -

NEW YORK

NEW "ATS" #633-1

(NP)

NEW "ATS" #634-1

UE(NP)

UE(EP)

AutoCA