08_71_00_USMMA_05-26-2015.pdf

United States Merchant Marine Academy NY13515.06 May 29, 2015 Zero Deck Renovations 08 71 00-1 Door Hardware Kings Point, New York

DOOR HARDWARE SECTION 08 71 00

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section Includes

1. Furnishing and installation of all mechanical and electrical finish hardware necessary for all doors, and hardware as specified herein and as enumerated in hardware sets and as indicated and required by actual conditions at the building.

The hardware shall include the furnishing of all necessary screws, bolts, expansion shields, drop plates, and all other devices necessary for the proper application of the hardware. Installation shall include field modification and preparation of existing doors and/or frames for new hardware being installed. Provide necessary fillers, Dutchmen, reinforcements, and fasteners for mounting new hardware and to cover existing door/frame preps.

B. Related Sections

1. Section 06 10 00 - Rough Carpentry

2. Section 08 11 13 - Hollow Metal Doors and Frames

3. Section 08 14 16 - Flush Wood Doors

4. Section 08 41 13 - Aluminum-Framed Entrances and Storefronts

5. Section 08 80 00 - Glazing

C. Specific Omissions: Hardware for the following is specified or indicated elsewhere, unless specifically listed in the hardware sets:

1. Windows

2. Cabinets of all kinds, including open wall shelving and locks.

3. Signage, except as noted.

4. Complete toilet accessories including coat hooks, unless note otherwise.

5. Overhead doors, unless noted otherwise.

1.3 REFERENCES

A. Applicable state and local building codes and standards.

B. FIRE/LIFE SAFETY

1. NFPA - National Fire Protection Association

a. NFPA 70 – National Electric Code

b. NFPA 80 - Standard for Fire Doors and Fire Windows

Zero Deck Renovations 08 71 00-2 Door Hardware Kings Point, New York

c. NFPA 101 - Life Safety Code

d. NFPA 105 - Smoke and Draft Control Door Assemblies

2. State Fire Safety Code and Amendments to CT Supplement

C. UL - Underwriters Laboratories

1. UL 10B - Fire Test of Door Assemblies

2. UL 10C - Positive Pressure Test of Fire Door Assemblies

3. UL 1784 - Air Leakage Tests of Door Assemblies

4. UL 305 - Panic Hardware

D. Accessibility

1. ADA - Americans with Disabilities Act

2. ICC (CABO) / ANSI A117.1 - Accessible and Usable Buildings and Facilities

E. DHI - Door and Hardware Institute

1. Sequence and Format for the Hardware Schedule

2. Recommended Locations for Builders Hardware

F. ANSI - American National Standards Institute

1. ANSI/BHMA A156.1 - A156.29, and ANSI A156.31 - Standards for Hardware and Specialties

1.4 SUBMITTALS

A. General: Submit the following under provisions of Section 01 33 00. Prior to submittal field verify existing doors and/or frames receiving new hardware and/or existing conditions receiving new openings. Verify new hardware is compatible with the existing door/frame preparation and/or existing conditions. Advise architect within the submittal package of incompatibility or issues.

B. Catalog Cuts: Product data including manufacturers' technical product data for each item of door hardware, installation instructions, maintenance of operating parts and finish, and other information necessary to show compliance with requirements.

C. Final Hardware Schedule Content: Submit schedule with hardware sets in vertical format as illustrated by the Sequence of Format for the Hardware Schedule as published by the Door and Hardware Institute. Indicate complete designations of each item required for each door or opening, Include the following information:

1. Door Index; include door number, heading number, and Architects hardware set number.

2. Opening Lock Function Spreadsheet; list locking device and function for each opening.

3. Type, style, function, size, and finish of each hardware item.

4. Name and manufacturer of each item.

5. Fastenings and other pertinent information.

Zero Deck Renovations 08 71 00-3 Door Hardware Kings Point, New York

6. Location of each hardware set cross-referenced to indications on Drawings.

7. Explanation of all abbreviations, symbols, and codes contained in schedule.

8. Mounting locations for hardware.

9. Door and frame sizes and materials.

10. Name and phone number for the local manufacturer's representative for each product.

11. Operational Description of openings with any electrified hardware (locks, exits, electromagnetic locks, electric strikes, automatic operators, door position switches, magnetic holders or closer/holder units, and/or access control components).

Operational description should include how the door will operate on egress, ingress, and/or fire/smoke alarm connection.

D. Key Schedule: After a keying meeting between representatives of the Owner, Architect, hardware supplier, and, if requested, the representative for the lock manufacturer, provide a keying schedule, listing the levels of keying, as well as an explanation of the key system's function, the key symbols used, and the door numbers controlled. Utilize ANSI A156.28 “Recommended Practices for Keying Systems” as a guideline for nomenclature, definitions, and approach for selecting the optimal keying system.

E. Samples: If requested by the Architect, submit production sample or sample installations as requested of each type of exposed hardware unit in the finish indicated, and tagged with a full description for coordination with the schedule.

1. Samples will be returned to the supplier in like-new condition. Units that are acceptable to the Architect may, after final check of operations, be incorporated into the Work, within limitations of key coordination requirements.

F. Templates: After final approval of the hardware schedule, provide templates for doors, frames, and other work specified to be factory prepared for the installation of door hardware.

G. Riser and Wiring Diagrams: After final approval of the hardware schedule, submit riser and wiring diagrams as required for the proper installation of complete electrical, electromechanical, and electromagnetic products.

H. Operations and Maintenance Data: Provide in accordance with Division 1 and include the following:

1. Complete information on care, maintenance, and adjustment; data on repair and replacement parts, and information on preservation of finishes.

2. Catalog pages for each product.

3. Name, address, and phone number of local representative for each manufacturer.

4. Parts list for each product.

5. Copy of final approved hardware schedule, edited to reflect “As installed.”

6. Copy of final keying schedule.

7. As installed “Wiring Diagrams” for each opening connected to power, both low voltage and 110 volts.

8. One (1) complete set of special tools required for maintenance and adjustment of hardware, including changing of cylinders.

9. Copy of warranties including appropriate reference numbers for manufacturers to identify the project.

Zero Deck Renovations 08 71 00-4 Door Hardware Kings Point, New York

I. Certificates of Compliance: Upon request of Architect or Authority Having Jurisdiction certificates of compliance for fire-rated hardware and installation instructions shall be made available.

1.5 QUALITY ASSURANCE

A. Substitutions: Products are to be those specified to ensure a uniform basis of acceptable materials. Requests for substitutions must be made in accordance with Division 1 requirements. If proposing a substitute product, submit product data for the proposed item with product data for the specified item and indicate basis for substitution and savings to be made. Provide sample if requested. Certain products have been selected for their unique characteristics and particular project suitability.

1. Items specified as "no substitute” shall be provided exactly as listed.

2. Items listed with no substitute manufacturers listed have been requested by the

Owner or Architect to match existing for continuity and/or future performance and maintenance standards or because there is no known equal product.

3. If no other products are listed in a category, then "no substitute" is implied.

B. Supplier Qualifications: A recognized architectural hardware supplier, with warehousing facilities in the Project's vicinity, that has a record of successful in-service performance for supplying door hardware similar in quantity, type, and quality to that indicated for this Project and that provides a certified Architectural Hardware Consultant (AHC) available to the Owner, Architect, and Contractor, at reasonable times during the course of the Work for consultation.

C. Single Source Responsibility: Obtain each type of hardware (latch and locksets, hinges, exit devices, closers, etc.) from a single manufacturer.

D. Fire-Rated Openings: Provide door hardware for fire-rated openings that complies with NFPA Standard No. 80 and requirements of authorities having jurisdiction. Provide only items of door hardware that are listed and are identical to products tested by Underwrites Laboratories, Intertek Testing Services, or other testing and inspecting organizations acceptable to the authorities having jurisdiction for use on types and sizes of doors indicated in compliance with requirements of fire-rated door and door frame labels.

E. Electronic Security Hardware: When electrified hardware is included in the hardware specification, the hardware supplier must employ an individual knowledgeable in electrified components and systems, who is capable of producing wiring diagrams and consulting as needed. Coordinate installation of the electronic security hardware with the Architect and electrical engineers and provide installation and technical data to the Architect and other related subcontractors. Upon completion of electronic security hardware installation, inspect and verify that all components are working properly.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Tag each item or package separately with identification related to the final hardware schedule, and include installation instructions with each item or package.

Zero Deck Renovations 08 71 00-5 Door Hardware Kings Point, New York

B. Each article of hardware shall be individually packaged in manufacturer's original packaging.

C. Contractor will provide secure lock-up for door hardware delivered to the Project, but not yet installed. Control handling and installation of hardware items so that completion of Work will not be delayed by hardware losses both before and after installation.

D. Items damaged in shipment shall be replaced promptly and with proper material and paid for by whomever did the damage or caused the damage to occur.

E. Hardware shall be handled in a manner to avoid damage, marring, or scratching.

Irregularities that occur to the hardware after it has been delivered to the Project shall be corrected, replaced, or repaired by the Contractor. Hardware shall be protected against malfunction due to paint, solvent, cleanser, or any chemical agent.

F. No direct shipments will be allowed unless approved by the Contractor.

1.7 WARRANTY

A. Provide manufacturer's warrantees as specified in Division 01 and as follows:

1. Closers: 10 years.

2. Exit Devices: 3 years, except electrified exit devices, 1 year.

3. Locksets: 3 years.

4. Continuous Hinges: Lifetime warranty.

5. Other hardware: 1 year.

B. No liability is to be assumed where damage or faulty operation is due to improper installation, improper use, or abuse.

C. Products judged to be defective during the warranty period shall be replaced or repaired in accordance with the manufacturer's warranty, at no additional cost to the Owner.

1.8 MAINTENANCE

A. Maintenance Tools and Instructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Owner's continued adjustment, maintenance, and removal and replacement of door hardware.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. The Awarding Authority has determined that certain products should be selected for their unique characteristics and particular project suitability to insure continuity of existing and future performance and maintenance standards. After investigating available product offerings the Awarding Authority has elected to prepare proprietary specifications. These products are specified with the notation: “No Substitute” (NO

OTHER PRODUCTS WILL BE CONSIDERED FOR THOSE LISTED IN PROJECTS

DOCUMENTS.)

Zero Deck Renovations 08 71 00-6 Door Hardware Kings Point, New York

B. Approval of manufacturers other than those listed shall be in accordance with Paragraph 1.5.A.

C. Note that even though an acceptable substitute manufacturer may be listed, the product must provide all the functions and features of the specified product or it will not be approved.

Item Scheduled Manufacturer Acceptable Substitute Hinges Ives (IVE) Hager, McKinney Continuous Hinges Ives (IVE) Roton, Stanley Flush Bolts Ives (IVE) Burns, Rockwood Locksets & Deadlocks Sargent (SAR) No Substitute Exit Devices Von Duprin (VON) No Substitute Magnetic Locks - Movement Exit Delay System

Schlage Electronics (SCE) Dynalock, Security Door Controls

Power Supplies Schlage Electronics (SCE) Dynalock, Security Door Controls

Door Closers LCN (LCN) No Substitute Door Trim Ives (IVE) Burns, Rockwood Protection Plates Ives (IVE) Burns, Rockwood Overhead Stops Glynn-Johnson (GLY) Rixson, Sargent Stops & Holders Ives (IVE) Burns, Rockwood Thresholds & Weatherstrip

Zero (ZER) Pemko, NGP

Silencers Ives (IVE) Burns, Rockwood Cylinders & Keying Sargent (SAR) No Substitute

D. Hand of Door: Drawings show direction of slide, swing, or hand of each door leaf.

Furnish each item of hardware for proper installation and operation of door movement as shown.

E. Where the hardware specified is not adaptable to the finished shape or size of the members requiring hardware, furnish suitable types having the same operation and quality as the type specified, subject to the Architect's approval.

2.2 MATERIALS

A. Fasteners

1. Provide hardware manufactured to conform to published templates, generally prepared for machine screw installation.

2. Furnish screws for installation with each hardware item. Finish exposed (exposed under any condition) screws to match hardware finish, or, if exposed in surfaces of other work, to match finish of this other work as closely as possible including "prepared for paint" surfaces to receive painted finish.

3. Provide concealed fasteners for hardware units that are exposed when door is closed except to the extent that no standard units of type specified are available with concealed fasteners. Do not use thru-bolts for installation where bolt head or nut on opposite face is exposed in other work unless their use is the only means of

Zero Deck Renovations 08 71 00-7 Door Hardware Kings Point, New York reinforcing the work adequately to fasten the hardware securely. Review door specification and advise Architect if thru-bolts are required.

4. Hardware shall be installed with the fasteners provided by the hardware manufacturer.

B. Hinges

1. Provide five-knuckle, ball bearing hinges of type, material, and height as outlined in the following guide for this specification:

a. 1-3/4 inch thick doors, up to and including 36 inches wide:

Exterior: standard weight, bronze/stainless steel, 4-1/2 inches high Interior: standard weight, steel, 4-1/2 inches high

b. 1-3/4 inch thick doors over 36 inches wide:

Exterior: heavy weight, bronze/stainless steel, 5 inches high Interior: heavy weight, steel, 5 inches high

c. 2 inches or thicker doors:

Exterior: heavy weight, bronze/stainless steel, 5 inches high Interior: heavy weight, steel, 5 inches high

2. Provide three hinges per door leaf for doors 90 inches or less in height, and one additional hinge for each 30 inches of additional door height.

3. Where new hinges are specified for existing doors and/or existing frames, the new hinge size must be identical to hinge preparation present in the existing door and/or existing frame.

4. Hinge Pins: Except as otherwise indicated, provide hinge pins as follows:

a. Steel Hinges: Steel pins

b. Non-Ferrous Hinges: Stainless steel pins

c. Out-Swinging Exterior Doors: Non-removable pins

d. Out-Swinging Interior Lockable Doors: Non-removable pins

e. Interior Non-lockable Doors: Non-rising pins

5. The width of hinges shall be 4-1/2 inches at 1-3/4 inch thick doors, and 5 inches at

2 inches or thicker doors. Adjust hinge width as required for door, frame, and/or wall conditions to allow proper degree of opening.

6. Acceptable manufacturers and/or products: Ives 5BB series, Hager BB series, McKinney TA/T4A series.

C. Continuous Hinges

1. Provide aluminum geared continuous hinges conforming to ANSI A156.25, Grade 2.

2. Provide aluminum geared continuous hinges, where specified in the hardware sets, fabricated from 6063-T6 aluminum, with .25 inch diameter Teflon coated stainless steel hinge pin.

3. Provide split nylon bearings at each hinge knuckle for quiet, smooth, self-lubricating operation.

4. Hinges shall be capable of supporting door weights up to 450 pounds, and shall be successfully tested for 1,500,000 cycles.

Zero Deck Renovations 08 71 00-8 Door Hardware Kings Point, New York

5. On fire-rated doors, provide aluminum geared continuous hinges that are classified for use on rated doors by a testing agency acceptable to the authority having jurisdiction.

6. Provide aluminum geared continuous hinges with electrified option where specified.

Provide with sufficient number and gage of concealed wires to accommodate electric function of specified hardware.

7. Install hinges with fasteners supplied by manufacturer. Hole pattern shall be symmetrically patterned.

8. Acceptable manufacturers and/or products: Ives, Roton, Stanley.

D. Flush Bolts

1. Provide automatic and manual flush bolts with forged bronze face plates, extruded brass levers, and with wrought brass guides and strikes. Provide 12 inch steel or brass rods at doors up to 90 inches in height. Top rods at manual flush bolts for doors over 90 inches in height shall be increased by 6 inches for each additional 6 inches of door height. Provide dust-proof strikes at each bottom flush bolt.

2. Acceptable manufacturers and/or products: Ives, Burns, Rockwood.

E. Mortise Locks

1. Provide mortise locks certified as ANSI A156.13, Grade 1 Operational, Grade 1 Security, and manufactured from heavy gauge steel, containing components of steel with a zinc dichromate plating for corrosion resistance. Lock case shall be multi-function and field reversible for handing without opening the case. Cylinders:

Refer to 2.04 KEYING.

2. Provide locks with a standard 2-3/4 inches backset with a full 3/4 inch throw stainless steel mechanical anti-friction latchbolt. Deadbolt shall be a full 1 inch throw, constructed of stainless steel.

3. Provide standard ASA strikes unless extended lip strikes are necessary to protect trim.

4. Lever trim shall be solid brass, bronze, or stainless steel, cast or forged in the design specified, with wrought roses and external lever spring cages. Levers shall be thru-bolted to assure proper alignment, and shall have a 2-piece spindle.

a. Lever design shall be Sargent L to match existing finish 32D (BHMA 630).

b. Lever trim on the secure side of doors serving rooms considered by the authority having jurisdiction to be hazardous shall have a tactile warning.

5. Acceptable manufacturers and/or products: Sargent 8200 Lever Lock, finish 32D satin stainless steel (BHMA 630) No Substitute.

F. Exit Devices

1. Provide exit devices tested to ANSI/BHMA A156.3 Grade 1, and UL listed for Panic Exit and/or Fire Exit Hardware. Cylinders: Refer to 2.04 KEYING.

2. Provide touchpad type exit devices, fabricated of brass, bronze, stainless steel, or aluminum, plated to the standard architectural finishes to match the balance of the door hardware.

3. Exit devices shall incorporate a fluid damper or other device that eliminates noise associated with exit device operation. Touchpad shall extend a minimum of one

Zero Deck Renovations 08 71 00-9 Door Hardware Kings Point, New York half of the door width, but not the full length of the exit device rail. End-cap will have two-point attachment to door. Touch-pad shall match exit device finish, and shall be stainless steel for US26, US26D, US28, US32, and US32D finishes; for all other finishes, the touch-pad finish shall be of compatible finish to exit device. Only compression springs will be used in devices, latches, and outside trims or controls.

4. Devices to incorporate a deadlatching feature for security and/or for future addition of alarm kits and/or other electrical requirements.

5. Vertical rod devices shall be capable of being field modified to less bottom rod devices by removal of bottom rod and adding firing pin(s), if required at fire rated openings.

6. Provide manufacturer's standard strikes.

7. Provide exit devices cut to door width and height. Locate exit devices at a height recommended by the exit device manufacturer, allowable by governing building codes, and approved by the Architect.

8. Mechanism case shall sit flush on the face of all flush doors, or spacers shall be furnished to fill gaps behind devices. Where glass trim or molding projects off the face of the door, provide glass bead kits.

9. Non-fire-rated exit devices shall have cylinder dogging.

10. Acceptable manufacturers and/or products: Von Duprin 99 series, No Substitute.

G. Roller Latches

1. Provide roller latches with a 4-7/8 inches strike at single doors to fit ANSI frame prep. If dummy levers are used in conjunction with roller latch mount the roller latch at a height as to not interfere with the proper mounting and height of the dummy lever.

2. Provide roller latches 2-1/4 inches full lip strike at pair doors. Mount roller in the top rail of each leaf per manufacturer’s template.

3. Acceptable manufacturers and/or products: Ives, Burns, Rockwood.

H. Magnetic Locks - Movement Exit Delay System

1. Provide movement exit delay systems complete with initiation device, magnetic lock, alarm, authorized reset/momentary release device, logic timer, and alarm output contacts.

2. Provide movement exit delay system that meets NFPA 101 Life Safety Code governing delayed egress, and/or other local and national fire codes acceptable to the authority having jurisdiction as required.

3. Provide magnetic locks conforming to ANSI/BHMA A156.23 classification criteria including a minimum holding force of 1500 LBF.

4. Provide magnetic locks equipped with a SPDT Magnetic Bond Sensing device to monitor whether sufficient magnetic holding force exists to ensure adequate locking and SPDT Door Status Monitor device to monitor whether the door is open or closed. The bond sensors shall be fully concealed within the electromagnet to resist tampering or damage.

5. Provide tamper proof fasteners, mounting brackets, and spacer bars required for mounting and details.

6. Provide a power supply recommended and approved by the manufacturer of the delayed egress magnetic locks.

Zero Deck Renovations 08 71 00-10 Door Hardware Kings Point, New York

7. Acceptable manufacturers and/or products: Schlage Electronics M490DE DSM/MBS/SEC/ATS/BOCA series, Dynalock 3101B DSM/DYNST/ATS/BOCA, Security Door Controls 1500 DPS/BA/ATS/BD series.

8. (OPTION: 1650 LBF) Acceptable manufacturers and/or products: Schlage Electronics M490DE DSM/MBS/SEC/ATS/BOCA series.

I. Power Supplies

1. Provide power supplies, recommended and approved by the manufacturer of the electrified locking component, for the operation of electrified locks, electrified exit devices, magnetic locks, electric strikes, and other components requiring a power supply.

2. Provide the appropriate quantity of power supplies necessary for the proper operation of the electrified locking component and/or components as recommended by the manufacturer of the electrified locking components with consideration for each electrified component utilizing the power supply, the location of the power supply, and the approved wiring diagrams. Locate the power supplies as directed by the Architect.

3. Provide a power supply that is regulated and filtered 24 VDC, or as required, and UL class 2 listed.

4. Provide a power supply with emergency release terminals, where required, that allow the release of all devices upon activation of the fire alarm system complete with fire alarm input for initiating “no delay” exiting mode.

5. Acceptable manufacturers and/or products: Schlage Electronics PS900 series, Dynalock 5000 series, Security Door Controls 600 series.

J. Door Closers

1. Provide door closers certified to ANSI/BHMA A156.4 Grade 1 requirements by a BHMA certified independent testing laboratory. Surface mounted mechanical closers shall be certified to exceed ten million (10,000,000) full load cycles by a recognized independent testing laboratory. Closers shall be ISO 9000 certified.

Units shall be stamped with date of manufacture code.

2. Door closers shall have fully hydraulic, full rack and pinion action with a high strength cast iron cylinder, and shall utilize full complement bearings at shaft.

Cylinder body shall be 1-1/2 inch diameter, and double heat-treated pinion journal shall be 11/16 inch diameter.

3. Provide hydraulic fluid requiring no seasonal closer adjustment for temperatures ranging from 120 degrees F to -30 degrees F. Fluid shall be fireproof and shall pass the requirements of the UL10C “positive pressure” fire test.

4. Spring power shall be continuously adjustable over the full range of closer sizes, and allow for reduced opening force as required by accessibility codes and standards. Hydraulic regulation shall be by tamper-proof, non-critical valves.

Closers shall have separate adjustment for latch speed, general speed, and backcheck.

5. Provide closers with a solid forged steel main arms and factory assembled heavy-duty forged forearms for parallel arm closers. When closers are parallel arm mounted, provide closers which mount within a 6-inch top rail without the use of a mounting plate so that closer shall not be visible through vision panel from pull side.

6. Closers shall not incorporate Pressure Relief Valve (PRV) technology.

Zero Deck Renovations 08 71 00-11 Door Hardware Kings Point, New York

7. Closer cylinders, arms, adapter plates, and metal covers shall have a powder coating finish which has been certified to exceed 100 hours salt spray testing as described in ANSI Standard A156.4 and ASTM B117, or shall have special rust inhibitor (SRI).

8. Provide special templates, drop plates, mounting brackets, or adapters for arms as required for details, overhead stops, and other finish hardware items interfering with closer mounting.

9. Mount closers on room side of corridor doors, inside of exterior doors, and stair side of stairway doors from corridors. Closers shall not be visible in corridors, lobbies and other public spaces unless approved by Architect.

10. Door closers meeting this specification: LCN 4040XP series, No Substitute.

K. Door Trim

1. Provide push plates 4 inches wide x 16 inches high x 0.050 inch thick and beveled 4 edges. Where width of door stile prevents use of 4 inches wide plate, adjust width to fit.

2. Provide offset pulls of solid bar stock, diameter and length as scheduled. Where required, mount back to back with push bar.

3. Provide pulls of solid bar stock, diameter and length as scheduled. Where required, mount back to back with push bar.

4. Acceptable manufacturers and/or products: Ives, Burns, Rockwood.

L. Protection Plates

1. Provide kick plates, mop plates, and armor plates minimum of 0.050 inch thick as scheduled. Furnish with machine or wood screws, finished to match plates. Sizes of plates shall be as follows:

a. Kick Plates – 10 inches high x 2 inches less width of door on single doors, 1 inch less width of door on pairs

2. Acceptable manufacturers and/or products: Ives, Burns, Rockwood.

M. Overhead Stops and Overhead Stop/Holders

1. Provide heavy or medium duty and concealed or surface mounted overhead stop or overhead stop/holder for interior doors as specified. Provide medium duty surface mounted overhead stop for interior doors and at any door that swings more than 140 degrees before striking a wall, open against equipment, casework, sidelights, and/or where conditions do not allow a wall stop or a floor stop presents a tripping hazard.

2. Where overhead holders are specified provide friction type at doors without a closer and positive type at doors with a closer.

3. Acceptable manufacturers and/or products: Glynn-Johnson, Rixson, Sargent.

N. Door Stops and Holders

1. Provide door stops for all doors in accordance with the following requirements:

Zero Deck Renovations 08 71 00-12 Door Hardware Kings Point, New York

a. Provide wall stops wherever possible. Provide convex type where mortise type locks are used and concave type where cylindrical type locks are used.

b. Where wall stops cannot be used, provide dome type floor stops of the proper height.

c. At any opening where a wall or floor stop cannot be used, a medium duty surface mounted overhead stop shall be used.

2. Acceptable manufacturers and/or products: Ives, Burns, Rockwood.

O. Thresholds, Seals, Door Sweeps, Automatic Door Bottoms, and Gasketing

1. Provide thresholds, weatherstripping (including door sweeps, seals, astragals) and gasketing systems (including smoke, sound, and light) as specified and per architectural details. Match finish of other items as closely as possible. Size of thresholds shall be as follows:

a. Saddle Thresholds – 1/2 inch high x jamb width x door width

2. Provide door sweeps, seals, astragals, and auto door bottoms only of type where resilient or flexible seal strip is easily replaceable and readily available.

3. Acceptable manufacturers and/or products: National Guard, Reese, Zero.

P. Silencers

1. Provide "Push-in" type silencers for each hollow metal or wood frame. Provide three for each single frame and two for each pair frame. Omit where gasketing is specified or required by code.

2. Acceptable manufacturers and/or products: Ives, Burns, Rockwood.

2.3 FINISHES

A. Finish of all hardware shall be US26D (BHMA 626/652) with the exceptions as follows:

1. Hinges at Exterior Doors: US32D (BHMA 630).

2. Continuous Hinges: US28 (BHMA 689).

3. Push Plates, Pulls, and Push Bars: US32D (BHMA 630).

4. Protection Plates: US32D (BHMA 630).

5. Overhead Stops and Holders: US32D (BHMA 630).

6. Door Closers: Powder Coat to Match.

7. Wall Stops: US32D (BHMA 630).

8. Weatherstipping: Clear Anodized Aluminum.

9. Thresholds: Mill Finish Aluminum.

2.4 KEYING

A. Provide cores and cylinders for the Owner’s Existing Sargent key system conforming to the following requirements:

1. Provide removable core cylinders at all keyed devices. Provide construction cores with construction master keying for use during construction. The hardware supplier, accompanied by the Owner or Owner’s security agent, shall install permanent

Zero Deck Renovations 08 71 00-13 Door Hardware Kings Point, New York keyed cores upon completion of the project. The temporary construction cores are to be returned to the hardware supplier.

2. Provide permanent cores and cylinders keyed into the existing key system as directed by the Owner. Provide owner with a copy of the bitting list, return receipt requested.

3. The hardware supplier, accompanied by a qualified factory representative for the manufacturer of the cores and cylinders, shall meet with Owner and Architect to review keying requirements and lock functions prior to ordering finish hardware.

Submit a keying schedule to Architect for approval.

4. Provide keys as directed by the owner.

5. Deliver all keys and/or key blanks from the factory or authorized distributor directly to the Owner in sealed containers, return receipt requested. Failure to comply with these requirements may be cause to require replacement of all or any part of the keying system that was compromised at no additional cost to the Owner.

6. Approved products: Sargent, No Substitute.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Prior to installation of any hardware, examine all doors, frames, walls and related items for conditions that would prevent proper installation of finish hardware. Correct all defects prior to proceeding with installation.

3.2 INSTALLATION

A. Coordination:

1. Prior to installation of hardware, schedule and hold a meeting for the purpose of instructing installers on proper installation and adjustment of finish hardware.

Representatives of locks, exit devices, closers, automatic operators, and electrified hardware shall conduct training; provide at least 10 days notice to representatives.

After training a letter of compliance, indicating when the training was held and who was in attendance, shall be sent to the Architect.

2. Prior to ordering electrified hardware, schedule and hold a meeting for the purpose of coordinating finish hardware with security, electrical, doors and frames, and other related suppliers. A representative of the supplier of finish hardware, and doors and frames, the electrical subcontractor, and the Owner’s security contractor shall meet with the Owner, Architect, and General Contractor prior to ordering finish hardware. After meeting a letter of compliance, indicating when the training was held and who was in attendance, shall be sent to the Architect.

B. Hardware will be installed by qualified tradesmen, skilled in the application of commercial grade hardware. For technical assistance if necessary, installers may contact the manufacturer’s rep for the item in question, as listed in the hardware schedule.

C. Mount hardware units at heights indicated in “Recommended Locations for Builders Hardware for Standard Steel Doors and Frames” by the Door and Hardware Institute.

Zero Deck Renovations 08 71 00-14 Door Hardware Kings Point, New York

D. Install each hardware item in compliance with the manufacturer’s instructions and recommendations, using only the fasteners provided by the manufacturer.

E. Do not install surface mounted items until finishes have been completed on the substrate. Protect all installed hardware during painting.

F. Set units level, plumb and true to line and location. Adjust and reinforce the attachment substrate as necessary for proper installation and operation.

G. Operating parts shall move freely and smoothly without binding, sticking, or excessive clearance.

H. Existing Doors and/or Frames: Remove existing hardware being replaced, tag, and store according to contract documents. Field modify and prepare existing door and/or frame for new hardware being installed. Provide necessary fillers, Dutchmen, reinforcements, and fasteners for mounting new hardware and to cover existing door/frame preps.

I. Wire (including low voltage), conduit, junction boxes, and pulling of wire is by Division 16, Electrical. Electrical Contractor shall connect wire to door position switches and run wire to central room or area as directed by the Architect. Wires shall be tested and labeled with the Architects opening number. Connections to/from power supplies to electrified hardware and any connection to fire/smoke alarm system, and/or smoke evacuation system where specified is by Division 26 Electrical.

3.3 ADJUSTING, CLEANING, AND DEMONSTRATING

A. Adjust and check each operating item of hardware and each door, to insure proper operation or function of every unit. Replace units which cannot be adjusted to operate freely and smoothly.

B. Where door hardware is installed more than one month prior to acceptance or occupancy of a space or area, return to the installation during the week prior to acceptance or occupancy and make a final check and adjustment of all hardware items in such space or area. Clean operating items as necessary to restore proper function and finish of hardware and doors. Adjust door control devices to compensate for final operation of heating and ventilating equipment.

C. Clean adjacent surfaces soiled by hardware installation.

D. Instruct Owner’s personnel in the proper adjustment, lubrication, and maintenance of door hardware and hardware finishes.

3.4 FIELD QUALITY CONTROL

A. Prior to Substantial Completion, the installer, as instructed by the manufacturers of locks, exit devices, closer, and any electrified hardware, shall perform the following work:

1. Examine and re-adjust each item of door hardware as necessary to restore function of doors and hardware to comply with specified requirements.

Zero Deck Renovations 08 71 00-15 Door Hardware Kings Point, New York

2. Consult with and instruct Owner’s personnel in recommended additions to the maintenance procedures.

3. Replace hardware items that have deteriorated or failed due to faulty design, materials, or installation of hardware units.

4. Prepare a written report of current and predictable problems of substantial nature in the performance of the hardware.

5. At completion of project, a qualified factory representative for the manufacturers of locksets, closer, exit devices, and access control products shall arrange and hold a training session to instruct the Owner’s personnel on the proper maintenance, adjustment, and/or operation of their respective products. After training a letter of compliance, indicating when the training was held and who was in attendance, shall be sent to the Architect.

3.5 PROTECTION

A. Provide for the proper protection of complete items of hardware until the Owner accepts the project as complete. Damaged or disfigured hardware shall be replaced or repaired by the responsible party.

3.6 HARDWARE SCHEDULE

A. Provide hardware for each door to comply with requirements of Section “Finish Hardware,” hardware set numbers indicated in door schedule, and in the following schedule of hardware sets.

B. It is intended that the following schedule includes complete items of finish hardware necessary to complete the work. If a discrepancy is found in the schedule, such as a missing item, improper hardware for a frame, door or fire codes, the preamble will be the deciding document.

C. Locksets, exit devices, and other hardware items are referenced in the Hardware Sets for series, type, and function. Refer to the preamble for special features, options, cylinders/keying, and other requirements.

D. Hardware Sets

HARDWARE SET: 01 - (MECHANICAL)

3 EA HINGE 5BB1 4.5 X 4.5 NRP 652 IVE

1 EA STOREROOM LOCK 8206 LL 626 SAR

1 EA SURFACE CLOSER 4040XP CUSH 689 LCN

3 EA SILENCER SR64 GRY IVE

TEMPLATE CLOSER FOR A 90 DEGREE STOP.

HARDWARE SET: 02 - (MULTI-FIXTURE BATHROOM)

Zero Deck Renovations 08 71 00-16 Door Hardware

3 EA HINGE 5BB1 4.5 X 4.5 652 IVE

1 EA PUSH PLATE 8200 4" X 16" 630 IVE

1 EA PULL PLATE 8303 10" 4" X 16" 630 IVE

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

1 EA FLOOR STOP FS438 626 IVE

INSTALL CLOSER ON PULL SIDE OF DOOR.

HARDWARE SET: 03 - (PUMP ROOM)

3 EA HW HINGE 5BB1HW 5 X 4.5 652 IVE

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

FIELD VERIFY HINGE SIZE REQUIRED FOR EXISTING FRAME.

HARDWARE SET: 04 - (ELECTRICAL)

1 EA PANIC HARDWARE 98-L-03-KN 626 VON

1 EA RIM CYLINDER RIM CYLINDER AS REQUIRED 626 SAR

1 EA SURFACE CLOSER 4040XP EDA 689 LCN

1 EA WALL STOP WS406/407CVX 630 IVE

HARDWARE SET: 05 - (OFFICE)

Zero Deck Renovations 08 71 00-17 Door Hardware Kings Point, New York

1 EA OFFICE LOCK 8205 LL 626 SAR

1 EA WALL STOP WS406/407CCV 630 IVE

HARDWARE SET: 06 - (FIRE/WATER, STORAGE, MECHANICAL, UPS)

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

FIELD VERIFY HINGE SIZE REQUIRED AT EXISTING FRAME LOCATIONS.

HARDWARE SET: 07 - (STORAGE, MECHANICAL)

FIELD VERIFY HINGE SIZE REQUIRED AT EXISTING FRAME LOCATIONS.

HARDWARE SET: 08 - (SINGLE-FIXTURE BATHROOM)

1 EA PRIVACY LOCK 8265 LL 626 SAR

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

FIELD VERIFY HINGE SIZE REQUIRED AT EXISTING FRAMES.

Zero Deck Renovations 08 71 00-18 Door Hardware

HARDWARE SET: 09 - (CONFERENCE, YOGA)

1 EA CLASSROOM LOCK 8237 LL 626 SAR

1 EA SURFACE CLOSER 4040XP CUSH 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

HARDWARE SET: 10 - (STORAGE, LAUNDRY, POST OFFICE)

1 EA CLASSROOM LOCK 8237 LL 626 SAR

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

HARDWARE SET: 11 - (VESTIBULE)

1 EA PUSH PLATE 8200 4" X 16" 630 IVE

1 EA PULL PLATE 8303 10" 4" X 16" 630 IVE

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

1 SET SEALS 188S BLK ZER

HARDWARE SET: 12 - (ALUMINUM ENTRY DOOR)

1 EA CONT. HINGE 112HD 628 IVE

1 EA PANIC HARDWARE CD-35A-NL-OP-388 626 VON

Zero Deck Renovations 08 71 00-19 Door Hardware Kings Point, New York

1 EA MORTISE CYLINDER MORTISE CYLINDER AS REQUIRED 626 SAR

1 EA RIM CYLINDER RIM CYLINDER AS REQUIRED 626 SAR

1 EA 90 DEG OFFSET

PULL

8190HD 10" 630 IVE

1 EA SURFACE CLOSER 4040XP SCUSH 689 LCN

1 EA THRESHOLD 8655A AL ZER

1 SEALS BY DOOR SUPPLIER

HARDWARE SET: 13 - (ELECTRIC CLOSET)

1 EA STOREROOM LOCK 8206 LL (TACTILE WARNING) 626 SAR

1 EA WALL STOP WS406/407CVX 630 IVE

HARDWARE SET: 14 - (STAIR DOOR WITH CARD ACCESS)

1 EA POWER TRANSFER EPT10 689 VON

1 EA DELAYED FIRE EXIT

HARDWARE

CX-9875-L-BE-F-03 626 VON

1 EA MORTISE CYLINDER MORTISE CYLINDER AS REQUIRED 626 SAR

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

1 EA FLOOR STOP FS438 626 IVE

1 SET SEALS 188S BLK ZER

1 EA POWER SUPPLY PS914 FA900 LGR VON

1 CARD READER BY OTHERS

OPERATIONAL DESCRIPTION

DOOR NORMALLY CLOSED AND LOCKED. CHEXIT DEVICE TO PROVIDE DELAYED

EGRESS FROM CORRIDOR. VALID CARD FROM CORRIDOR TO ALLOW AUTHORIZED

EGRESS WITHOUT ALARM OR DELAY. STAIR-SIDE LEVER WILL ALLOW FREE

PASSAGE TO CORRIDOR AT ALL TIMES. FIRE ALARM CONDITION MUST DISABLE

DELAY.

Zero Deck Renovations 08 71 00-20 Door Hardware

HARDWARE SET: 15 - (IT)

1 EA OFFICE LOCK 8205 LL 626 SAR

1 EA SURFACE CLOSER 4040XP CUSH 689 LCN

HARDWARE SET: 16 - (ALUMINUM VESTIBULE DOOR)

1 EA CONT. HINGE 112HD 628 IVE

1 SET PUSH/PULL BAR 9190HD-10" 630 IVE

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

HARDWARE SET: 17 - (AEROBICS)

6 EA HINGE 5BB1 4.5 X 4.5 NRP 652 IVE

2 EA MANUAL FLUSH

BOLT

FB458 626 IVE

1 EA DUST PROOF STRIKE DP2 626 IVE

1 EA CLASSROOM LOCK 8237 LL 626 SAR

1 EA SURFACE CLOSER 4040XP SCUSH 689 LCN

2 EA KICK PLATE 8400 10" X 1" LDW B4E 630 IVE

2 EA SILENCER SR64 GRY IVE

FURNISH DOOR CLOSER FOR ACTIVE LEAF ONLY.

HARDWARE SET: 18 - (GAME ROOM)

BOLT

FB458 626 IVE

1 EA DUST PROOF STRIKE DP2 626 IVE

Zero Deck Renovations 08 71 00-21 Door Hardware Kings Point, New York

1 EA CLASSROOM LOCK 8237 LL 626 SAR

1 EA SURFACE CLOSER 4040XP EDA 689 LCN

2 EA KICK PLATE 8400 10" X 1" LDW B4E 630 IVE

2 EA WALL STOP WS406/407CVX 630 IVE

FURNISH DOOR CLOSER FOR ACTIVE LEAF ONLY.

HARDWARE SET: 19 - (LOGISTICS)

1 EA OFFICE LOCK 8205 LL 626 SAR

1 EA OH STOP 100S 630 GLY

1 EA SURFACE CLOSER 4040XP REG ST-1630 689 LCN

1 EA TOP JAMB MTG

PLATE

4040-18TJ 689 LCN

INSTALL CLOSER ON DROP PLATE IN ACCORDANCE WITH SPECIAL TEMPLATE 1630

TO PROVIDE CLEARANCE FOR THE OVERHEAD STOP.

HARDWARE SET: 20 - (STORAGE)

6 EA HINGE 5BB1 4.5 X 4.5 652 IVE

BOLT

FB458 626 IVE

1 EA DUST PROOF STRIKE DP2 626 IVE

1 EA CLASSROOM LOCK 8237 LL 626 SAR

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

2 EA KICK PLATE 8400 10" X 1" LDW B4E 630 IVE

FURNISH DOOR CLOSER FOR PULL SIDE OF ACTIVE LEAF ONLY.

Zero Deck Renovations 08 71 00-22 Door Hardware

HARDWARE SET: 21 - (DATA ROOM)

BOLT

FB458 626 IVE

1 EA DUST PROOF STRIKE DP2 626 IVE

1 EA STOREROOM LOCK 8206 LL 626 SAR

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

2 EA KICK PLATE 8400 10" X 1" LDW B4E 630 IVE

FURNISH DOOR CLOSER FOR PULL SIDE OF ACTIVE LEAF ONLY.

HARDWARE SET: 22 - (BARBER SHOP, SALON, GAME ROOM)

1 EA PASSAGE SET 8215 LL 626 SAR

FIELD VERIFY HINGE SIZE REQUIRED AT EXISTING FRAMES.

HARDWARE SET: 23 - (CLOSET)

2 EA ROLLER LATCH RL32 626 IVE

2 EA SNGLE DUMMY 8293 LL 626 SAR

HARDWARE SET: 24 - (ELECTRICAL CLOSET)

Zero Deck Renovations 08 71 00-23 Door Hardware Kings Point, New York

3 EA HINGE 5BB1 4.5 X 4.5 NRP 652 IVE

1 EA STOREROOM LOCK 8206 LL (TACTILE WARNING) 626 SAR

HARDWARE SET: 25 - (SEAFARER)

1 EA PANIC HARDWARE CD-3547A-EO-LBR 626 VON

1 EA PANIC HARDWARE CD-3547A-NL-OP-LBR-388 626 VON

2 EA MORTISE CYLINDER MORTISE CYLINDER AS REQUIRED 626 SAR

1 EA RIM CYLINDER RIM CYLINDER AS REQUIRED 626 SAR

2 EA 90 DEG OFFSET

PULL

8190HD 10" 630 IVE

2 EA SURFACE CLOSER 4040XP SCUSH 689 LCN

HARDWARE SET: 26 - (STAIR DOOR WITH CARD ACCESS - EXISTING FRAME)

1 EA FIRE EXIT

HARDWARE

98-L-BE-F-03 626 VON

1 EA DELAYED EGRESS

MAG

M490DEP 628 SCE

1 EA SURFACE CLOSER 4040XP REG OR PA AS REQ 689 LCN

1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

1 EA FLOOR STOP FS438 626 IVE

1 SET SEALS 188S BLK ZER

1 EA PUSHBUTTON 621ALEX DA 629 SCE

1 EA MOTION SENSOR SCANII WHT SCE

1 EA POWER SUPPLY PS902 FA900 LGR SCE

1 CARD READER BY OTHERS

OPERATIONAL DESCRIPTION

DOOR NORMALLY CLOSED AND LOCKED. MAG-LOCK TO PROVIDE DELAYED EGRESS

FROM CORRIDOR. VALID CARD FROM CORRIDOR TO ALLOW AUTHORIZED EGRESS

WITHOUT ALARM OR DELAY. FROM STAIR, MOTION DETECTOR TO SENSE

APPROACHING OCCUPANT AND RELEASE MAG-LOCK, ALLOWING FREE PASSAGE

BACK TO THE CORRIDOR. SECONDARY WALL-MOUNTED RELEASE BUTTON IN STAIR

Zero Deck Renovations 08 71 00-24 Door Hardware Kings Point, New York

WILL CUT POWER TO THE MAG-LOCK, ALLOWING PASSAGE IN THE EVENT OF MOTION

DETECTOR FAILURE. MAG-LOCK MUST RELEASE ON FIRE ALARM.

END OF SECTION