DEVTHANE 379UVA info_ALL.pdf

Devoe Coatings is a member of the ICI Paints World Group

FEATURES

PERFORMANCE DATA

F

IN

IS

H

E S

H

IG

H P

E R

F O

R M

A N

C E

C O

AT

IN

G S

(09960)

09960

PRODUCT DESCRIPTION SPECIFICATION DATA

F

IN

IS

H

E S

H

IG

H P

E R

F O

R M

A N

C E

C O

AT

IN

G S

(0

ICI

Generic: Aliphatic Acrylic Polyurethane General Description: A high performance, two-compo-nent chemically-cured aliphatic urethane gloss enamel for use in areas where maximum gloss & color retention are required.

Typical Uses: For use on properly prepared and primed steel, concrete or steel floors, masonry, drywall, plaster, metal, concrete block, galvanized, aluminum, poured concrete, and glazed brick. Ideal for use on exterior or interior structural steel, piping, metal buildings, control cabinetry, conveyors, pumps, storage tank exteriors, motors, machinery, and transportation vehicles.

Advantages:

• Exceptional gloss and color retention

• Excellent abrasion and chemical resistance

• Easily applied by brush, roller or spray

• Wide color selection, including safety colors

• Excellent resistance to marring, chipping, and scratching

• Contains ultraviolet light absorber

Graffiti Resistance:

Excellent resistance to most graffiti materials such as spray paint, magic markers and lipstick. Contact your ICI Paints' Representative for more information on the graffiti removing cleaner to service your needs.

Limitations of Use: Color may change as temperature approaches 250°F (121°C) limit, but the film will remain intact.

Adhesion: (ASTM D 4541) – Excellent Salt Spray Resistance: (ASTM B 117) – Excellent Abrasion Resistance: (ASTM D 4060) – Excellent Humidity Resistance: (ASTM D 4585) – Excellent Exterior Exposure: 45° South Florida – Excellent Service Temperature Limits: 250°F (121°C) dry Hardness: (ASTM D 3363, 7 day cure @ 77°F (25°C) 4H

Chemical Resistance: (ASTM D 1308 – 24 hour contact) resists splash and spillage of alkalis, salts, moisture, oils, greases, foodstuffs and detergents.

Stain Resistance: (ASTM D 1308 – 1 week contact) Excellent. Resists stains such as crayon, lipstick, coffee, soil medium, shoe polish, grape juice, ink pen, marker, and spray paint.

Color: White (379K1000), ready-mixed & custom colors Finish: Gloss (90 units @ 60°) Reduction Solvent: T-9 or T-17 Thinner – see Thinning Clean-up Solvent: T-9 Thinner Weight/Gallon: 11.0 lbs./gal. (1.32 kg/L) – varies with color VOC (EPA 24): 2.60 lbs./gal. (311 g/L) – varies with color Solids By Volume (ASTM 2697-7 days): 63% ± 2% Theoretical Coverage at 1.0 Mil (25 microns)Dry: 1011

sq. ft./gal. (24.9 m2/L) Recommended Film Thickness: 2.0-3.0 mils (50-75 microns) dry – 3.2-4.8 mils (80-120 microns) wet Systems: Please consult the appropriate system guide, the particular job specification or your ICI Paints’ Representative for proper systems using this product.

Systems must be selected considering the particular environment involved.

Minimum Dry Time (ASTM D 1640): 2 mils (50 microns) DFT

Substrate Temperature 40°F (4°C) 60°F (16°C) 80°F (27°C) 100°F (38°C) Minimum Recoat 10 Hours 6 Hours 3 Hours 4 Hours Dry Hard >32 Hours 24 Hours 16 Hours 12 Hours Maximum Recoat

Self 2 Weeks 2 Weeks 2 Weeks 7 Days

Warning: The above table provides general guidelines only. Always consult your ICI Paints’ Representative for appropriate recoat windows since the maximum aged recoat time of this product may be significantly shortened or lengthened by a variety of conditions, including, but not lim-ited to humidity, surface temperature, and the use of additives or thin-ners. The use of accelerators or force curing may shorten the aged recoat of individual coatings. The above recoat windows may not apply if recoating with a product other than those listed above. If the maximum aged recoat window is exceeded, please consult your ICI Paints’ Representative for appropriate recommendations to enhance adhesion.

Failure to observe these precautions may result in intercoat delamination.

Shelf Life: Over 12 months at 77°F (25°C) – unopened.

Mix Ratio By Volume: 4 (base): 1 (converter) – see mixing instructions.

Induction: None Pot Life: 4 hours @ 77°F (25°C)

DANGER! FLAMMABLE. HARMFUL OR FATAL IF SWALLOWED. Read Label and Material Safety Data Sheet Prior to Use. See other cautions on last page. DSF3-0696

DEVTHANE

379UVA

Aliphatic Urethane Gloss Enamel (White, Ready-Mixed & Custom Colors)

Cat. # 379KXXXX

GENERAL SURFACE PREPARATION

DIRECTIONS FOR USE

SHIPPING

Tinting: Tint the appropriate base with CHROMA-CHEM* 844 colorants. (Do not use water based or other colorants.) Add colorants to only the base portion.

Mix thoroughly before adding the converter portion.

Thinning: Thinning is not normally required or desired, and excessive thinning can adversely affect application and appearance properties. However, at lower temperatures, small amounts (5% or less) of T-9 Thinner may be added depending on local VOC and air quality regulations. Small amounts (5% or less) of T-17 Thinner will improve roller or brush application on hot substrates. For end uses such as transportation vehicles where the smoothest, orange peel-free appearance is desired, additional thinning may be needed.

Mixing: DEVTHANE 379UVA Enamel is a two-component product supplied in 5 gallon or 1 gallon kits, which contain the proper ratio of ingredients. The entire contents of each container must be mixed together. It is important that all mixing equipment is free of moisture and that moisture does not contaminate the coating. Mix the base portion to obtain a smooth, homogeneous condition.

After mixing the base portion, add the converter slowly with continued agitation.

Mix thoroughly. The pot life of the mixed material is 4 hours at 77°F (25°C).

Higher temperatures will reduce working life of the coating; lower temperatures will increase it. Avoid storing or placing containers in direct sunlight.

Application: Apply by airless spray, air spray, roller or brush. For airless spray, any air, electric, or gas operated airless sprayer capable of 3,000 psi (207 bars) and able to support .011'' to .017'' tip sizes can be used. Multiple guns and long fluid lines require pumps with adequate capacity. For air spray application, use a professional grade conventional gun with a 0.70'' or larger fluid tip. Adust fluid and air pressure to get a good spray pattern.

All surfaces must be sound, clean, dry, and free of oil, grease, mildew, form release agents, laitance, and foreign matter. To insure the best appearance, the primer or undercoat should be smooth and free of any surface defects such as runs, dry spray or heavy orange peel. Use only products that are in compliance with local VOC regulations.

New Surfaces: Steel – Clean and prime with DEVRAN® 205, DEVRAN 220, DEVRAN 224HS, BAR-RUST® 231, BAR-RUST 233H, BAR-RUST 235, or TRU- GLAZE-WB™ 4030 primers. Concrete Block – Fill with DEVRAN 22O, DEVRAN 224HS primers or TRU-GLAZE-WB™ 4015 or BLOXFIL® 4000 blockfillers.

Fiberglass – Solvent wipe, scuff sand and solvent wipe again. Prime with DEVRAN 201 epoxy. Concrete Floors, Poured Concrete – Cure at least 30 days. pH must be 10.0 or lower before painting. Acid etch or abrasive blast slick, glazed concrete or concrete with laitance. Prime with DEVRAN 220, DEVRAN 224HS, BAR-RUST 231, BAR-RUST 233H, BAR-RUST 235, or TRU- GLAZE-WB 4030 primers or use PRE-PRIME™ 167 Penetrating Sealer.

Galvanized Steel and Aluminum – Remove dirt and oils by solvent cleaning or with DEVPREP® 88 Cleaner or other suitable cleaner followed by a thor-ough water rinsing. Prime with DEVRAN 205, DEVRAN 201 or DEVRAN 203 epoxy primers. Galvanized substrates must be test patched for adhesion prior to use due to the high variability of surface treatments.

Previously Painted Surfaces: Remove loose and peeling paint. Scuff sand glossy areas. Old coatings should be tested for lifting and bleeding. If they lift or bleed, remove them. Prime bare areas with a primer specified under New Surfaces.

WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS

ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT

WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424- LEAD or log on to www.epa.gov/lead.

Flash point: 80°F (27°C) Shipping Weight: 1 gallon kit - 12 lbs. (5.4 kg) Packaging: 1 gallon kit (3.785L) 5 gallon kit (18.925L) 5 gallon kit - 59 lbs. (26.8 kg)

0.80 gallon base 4.00 gallon base

0.20 gallon converter 1.00 gallon converter 379KXXXX (5/06)

Ad Stock #68659G *CHROMA-CHEM is a Registered Trademark of Creanova, Inc.

PRECAUTIONS

DANGER! FLAMMABLE LIQUID AND VAPOR. HARMFUL OR FATAL IF SWALLOWED. ASPIRATION HAZARD - CAN ENTER LUNGS AND CAUSE DAMAGE. HARMFUL IF INHALED. MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS, INCLUDING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN AND RESPIRATORY TRACT IRRITATION. MAY CAUSE ALLERGIC SKIN AND RESPIRATORY REACTION. OVEREXPOSURE MAY CAUSE BLOOD, LIVER, KIDNEY DAMAGE. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN. NOTICE: Products in this series contain solvents. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. For emergency information call

(800) 545-2643. Note: These warnings encompass the product series. Prior to use, read and follow product-specific MSDS and label information.

Keep away from heat, sparks and flame. Do not smoke. Vapors may ignite. Extinguish all flames, burners, stoves, heaters and pilot lights and disconnect all electrical motors and appliances before use and until all vapors are gone. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. If sanding is done, wear a dust mask to avoid breathing of sanding dust. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. Avoid contact with eyes and skin. If you experience eye watering, headaches, or dizziness, leave the area. If properly used, a respirator may offer additional protection. Obtain professional advice before using. Close container after each use. FIRST AID: For skin contact, wash thoroughly with soap and water. If any product remains, gently rub with petroleum jelly, vegetable or mineral/baby oil then wash again with soap and water. Repeat as needed. Remove contaminated clothing. For eye contact, flush immediately with plenty of water for at least 15 minutes.

Get medical attention. If swallowed, get medical attention immediately. If inhalation causes discomfort, remove to fresh air. If discomfort persists or breathing difficulty occurs, get medical attention. KEEP FROM FREEZING. DS174-1005

Note: Be sure all spray equipment and fluid lines are clean, and free of water or non-compatible solvents. For brush application, use good quality, dry, clean brushes. For roller application use new, short nap mohair rollers. Do not apply over wet surfaces or under very humid conditions where condensation or fog could settle on the coating during the cure process. Brushing and rolling may require multiple coats to achieve correct film thickness and/or hiding.

Spreading Rate: For maximum protection in corrosive areas, apply at 335 sq.

ft. per gallon (8.2 m2/L) or 3.0 mils (75 microns) dry-4.8 mils (120 microns) wet. In mild to moderate exposures, apply at 500 sq. ft. per gallon (12.25 m2/L) or 2.0 mils (50 microns) dry-3.2 mils (80 microns) wet. Make allowance for any losses due to over-spray or surface irregularities.

Dry Time: At 70°F (21°C) & 50% R.H., dries to recoat in 3 hours and dries hard in 16-24 hours.

Clean-up: Use T-9 Thinner.

Cure Acceleration: DEVTHANE Cure Accelerator 070A0000 may be used to accelerate cure of this urethane at or below 40˚F (5˚C). 070A0000 is prepackaged (5 fluid ounces in a one-half pint container) for field addition. The addition of one to two ounces per gallon of urethane (one to two containers per five gallons of urethane) will decrease the dry hard time approximately one-third to one-half respectively. The pot life will be reduced one-half to three-fourths.

Ultraviolet Light Absorbers (UVA): DEVTHANE Ultraviolet Llight Absorber 080A0000 is already contained in DEVTHANE 379UVA Enamel. Additional Ultraviolet Light Absorber is not required nor desired.

Back Page: 379KXXXX

ICI Paints Strongsville, Ohio, U.S.A.

800-654-2616 www.devoecoatings.com

LIMITATION OF LIABILITY: To the best of our knowledge, the technical data contained herein are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to conform to the specifications contained herein. WE MAKE NO OTHER WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE.

Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF

LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.

MATERIAL SAFETY DATA SHEET

The information contained herein is based on data available at the time of preparation of this data sheet which ICI Paints believes to be reliable. However, no warranty is expressed or implied regarding the accuracy of this data. ICI Paints shall not be responsible for the use of this information, or of any product, method or apparatus mentioned and you must make your own determination of its suitability and completeness for your own use, for the protection of the environment, and the health and safety of your employees and the users of this material.

Complies with OSHA hazard communication standard 29CFR1910.1200.

prepared 08/11/06 D

EVTH

A

N E 379 A

LIPH

ATIC

U R

ETH

A

N E G

LO

SS EN

A M

EL

IC

I Paints N orth A m erica 15885 Sprague R oad Strongsville, O hio 44136 EM

ER

G

EN

C Y

TELEPH

O

N E N

O . (800) 545-2643

HAZARDS IDENTIFICATION (ANSI Section 3) Primary route(s) of exposure : Inhalation, skin contact, eye contact, ingestion.

Effects of overexposure :

Inhalation : Irritation of respiratory tract. Prolonged inhalation may lead to. Inhalation of spray mist may cause irritation of respiratory tract. Mucous membrane irritation, fatigue, drowsiness, dizziness and/or lightheadedness, headache, uncoordination, nausea, vomiting, coughing, central nervous system depression, intoxication, anesthetic effect or narcosis, difficulty of breathing, allergic response, tremors, liver damage, kidney damage, pulmonary edema, pneumoconiosis, loss of consciousness, death. Possible sensitization to respiratory tract.

Skin contact : Irritation of skin. Prolonged or repeated contact can cause dermatitis, defatting, allergic response, severe skin irritation. Possible sensitization to skin.

Eye contact : Irritation of eyes. Prolonged or repeated contact can cause conjunctivitis, blurred vision, tearing of eyes, redness of eyes, severe eye irritation, corneal injury.

Ingestion : Ingestion may cause lung inflammation and damage due to aspiration of material into lungs, mouth and throat irritation, drowsiness, dizziness and/or lightheadedness, headache, uncoordination, nausea, vomiting, diarrhea, gastro-intestinal disturbances, abdominal pain, central nervous system depression, anesthetic effect or narcosis, difficulty of breathing, pulmonary edema, convulsions, loss of consciousness.

Medical conditions aggravated by exposure : Eye, skin, respiratory disorders, asthma-like conditions, kidney disorders, liver disorders.

FIRST-AID MEASURES (ANSI Section 4) Inhalation : Remove to fresh air. Restore and support continued breathing. Get emergency medical attention. Have trained person give oxygen if necessary. Get medical help for any breathing difficulty. Remove to fresh air if inhalation causes eye watering, headaches, dizziness, or other discomfort. Get medical attention if discomfort or irritation persists.

Skin contact : Wash thoroughly with soap and water. If any product remains, gently rub petroleum jelly, vegetable or mineral/baby oil onto skin. Repeated applications may be needed. Remove contaminated clothing. Wash contaminated clothing before re-use. If irritation occurs, consult a physician.

Eye contact : Flush immediately with large amounts of water, especially under lids for at least 15 minutes. If irritation or other effects persist, obtain medical treatment.

Ingestion : If swallowed, obtain medical treatment immediately.

FIRE-FIGHTING MEASURES (ANSI Section 5) Fire extinguishing media : Dry chemical or foam water fog. Carbon dioxide. Closed containers may explode when exposed to extreme heat or fire. Vapors may ignite explosively at ambient temperatures. Vapors are heavier than air and may travel long distances to a source of ignition and flash back. Vapors can form explosive mixtures in air at elevated temperatures. Closed containers may burst if exposed to extreme heat or fire. Dust explosion hazard. May decompose under fire conditions emitting irritant and/or toxic gases.

Fire fighting procedures : Water may be used to cool and protect exposed containers. Firefighters should use full protective clothing, eye protection, and self-contained breathing apparatus.

Hazardous decomposition or combustion products : Carbon monoxide, carbon dioxide, oxides of nitrogen, oxides of sulfur, ammonia, toxic gases, barium compounds, acrylic monomers.

ACCIDENTAL RELEASE MEASURES (ANSI Section 6) Steps to be taken in case material is released or spilled : Comply with all applicable health and environmental regulations. Eliminate all sources of ignition. Ventilate area. Ventilate area with explosion-proof equipment. Spills may be collected with absorbent materials. Use non-sparking tools. Evacuate all unnecessary personnel. Place collected material in proper container. Spilled material is extremely slippery. Complete personal protective equipment must be used during cleanup.

Vacuum with grounded equipment. Large spills - shut off leak if safe to do so. Dike and contain spill.

Pump to storage or salvage vessels. Use absorbent to pick up excess residue. Keep salvageable material and rinse water out of sewers and water courses. Small spills - use absorbent to pick up residue and dispose of properly.

HANDLING AND STORAGE (ANSI Section 7) Handling and storage : Store below 80f. Store below 100f (38c). Keep away from heat, sparks and open flame. Store in original container. Keep away from direct sunlight, heat and all sources of ignition. Keep container tightly closed in a well-ventilated area.

Other precautions : Use only with adequate ventilation. Do not take internally. Keep out of reach of children. Avoid contact with skin and eyes, and breathing of vapors. Wash hands thoroughly after handling, especially before eating or smoking. Keep containers tightly closed and upright when not in use. Avoid conditions which result in formation of inhalable particles such as spraying or abrading (sanding) painted surfaces. If such conditions cannot be avoided, use appropriate respiratory protection as directed under exposure controls/personal protection. Empty containers may contain hazardous residues. Ground equipment when transferring to prevent accumulation of static charge.

EXPOSURE CONTROLS/PERSONAL PROTECTION (ANSI Section 8) Respiratory protection : Respiratory protection is required for use in isocyanate containing environments. Consider type of application and environmental concentrations when selecting respiratory protection. Observe governmental regulations for respirator use. (29 CFR 1910.134(OSHA))(Canadian z94.4) The use of positive pressure supplied air respirator is mandatory when the airborne isocyanate concentrations are not known. Note: isocyanate based materials have been determined to cause allergic sensitization in humans. Avoid inhalation and dermal (skin) contact with the uncured material.

Ventilation : Provide dilution ventilation or local exhaust to prevent build-up of vapors. Use explosion-proof equipment. Use non-sparking equipment.

Personal protective equipment : Eye wash, safety shower, safety glasses or goggles. Impervious gloves, impervious clothing, face shield, apron, boots.

STABILITY AND REACTIVITY (ANSI Section 10) Under normal conditions : Stable see section 5 fire fighting measures Materials to avoid : Oxidizers, acids, reducing agents, bases, halogens, amines, water, peroxides, nitric acid, alcohols, caustics. Nitrates.

Conditions to avoid : Elevated temperatures, moisture, contact with oxidizing agent, sparks, open flame, ignition sources.

Hazardous polymerization : Will not occur

TOXICOLOGICAL INFORMATION (ANSI Section 11) Supplemental health information : Free diisocyanate may cause allergic reaction in susceptible persons. Notice - reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Other effects of overexposure may include toxicity to liver, kidney, lungs, central nervous system, blood.

Form: 379, Page 2 of 4, prepared 08/11/06

Carcinogenicity : The international agency for research on cancer (IARC) has classified carbon black as possibly carcinogenic to humans (group 2b) based on sufficient evidence in animals and inadequate evidence in humans. The international agency for research on cancer (IARC) has evaluated ethylbenzene and classified it as a possible human carcinogen (group 2b) based on sufficient evidence for carcinogenicity in experimental animals, but inadequate evidence for cancer in exposed humans. In a 2 year inhalation study conducted by the national toxicology program (NTP), ethylbenzene vapor at 750 ppm produced kidney and testicular tumors in rats and lung and liver tumors in mice. Genetic toxicity studies showed no genotoxic effects. The relevance of these results to humans is not known. In a lifetime inhalation study, exposure to 250 mg/m3 titanium dioxide resulted in the development of lung tumors in rats. These tumors occurred only at dust levels that overwhelmed the animals' lung clearance mechanisms and were different from common human lung tumors in both type and location. The relevance of these findings to humans is unknown but questionable. The international agency for research on cancer (IARC) has classified titanium dioxide as possibly carcinogenic to humans (group 2b) based on inadequate evidence of carcinogenicity in humans and sufficient evidence of carcinogenicity in experimental animals.

Reproductive effects : High exposures to xylene in some animal studies, often at maternally toxic levels, have affected embryo/fetal development. The significance of this finding to humans is not known.

Mutagenicity : No mutagenic effects are anticipated Teratogenicity : No teratogenic effects are anticipated

ECOLOGICAL INFORMATION (ANSI Section 12) No ecological testing has been done by ICI paints on this product as a whole.

DISPOSAL CONSIDERATIONS (ANSI Section 13) Waste disposal : Dispose in accordance with all applicable regulations. Avoid discharge to natural waters.

REGULATORY INFORMATION (ANSI Section 15) As of the date of this MSDS, all of the components in this product are listed (or are otherwise exempt from listing) on the TSCA inventory. This product has been classified in accordance with the hazard criteria of the CPR (controlled products regulations) and the MSDS contains all the information required by the CPR.

Physical Data (ANSI Sections 1, 9, and 14)

Product Code Description Wt. / Gal. VOC

gr. / ltr.

% Volatile by Volume

Flash Point

Boiling Range HMIS DOT, proper shipping name

379B1000 devthane 379 aliphatic urethane gloss enamel -white high-hiding base 10.55 363.83 42.40 80 f 212-595 330 paint, 3, UN1263, PGIII 379B3501 devthane 379 aliphatic urethane gloss enamel -white base 10.59 374.61 42.89 80 f 212-595 230 paint, 3, UN1263, PGIII 379B8557 devthane 379 aliphatic urethane gloss enamel -signal yellow base 8.70 402.06 46.22 80 f 212-450 230 paint, 3, UN1263, PGIII 379B9000 devthane 379 safety red 8.98 366.58 42.51 80 f 212-595 330 paint, 3, UN1263, PGIII 379B9200 devthane 379 aliphatic urethane gloss enamel safety orange base 8.85 350.40 40.75 80 f 212-595 330 paint, 3, UN1263, PGIII 379B9400 devthane 379 aliphatic urethane gloss enamel safety yellow base 10.34 371.86 43.48 80 f 212-595 330 paint, 3, UN1263, PGIII 379B9500 devthane 379 aliphatic urethane gloss enamel - white tint base 10.66 367.90 42.94 80 f 212-595 330 paint, 3, UN1263, PGIII 379B9501 devthane 379 aliphatic urethane gloss enamel -deep tint base 10.62 367.54 42.88 80 f 212-595 330 paint, 3, UN1263, PGIII 379B9502 devthane 379 aliphatic urethane gloss enamel -neutral tint base 10.67 350.28 40.74 80 f 212-595 330 paint, 3, UN1263, PGIII 379B9903 devthane 379 aliphatic urethane gloss enamel -black base 10.06 376.17 43.87 80 f 212-595 *330 paint, 3, UN1263, PGIII 379C0910 devthane 379 hs converter 9.40 112.85 13.00 135 f 293-293 *321 resin solution, combustible liquid, UN1866, PGIII

Ingredients Product Codes with % by Weight (ANSI Section 2)

Chemical Name Common Name CAS. No. 379B1000 379B3501 379B8557 379B9000 379B9200 379B9400 379B9500 379B9501 379B9502 379B9903 379C0910 benzene, ethyl- ethylbenzene 100-41-4 .1-1.0 .1-1.0 .1-1.0 2-heptanone methyl amyl ketone 110-43-0 10-20 10-20 10-20 10-20 10-20 10-20 10-20 10-20 10-20 10-20 quaternary ammonium compounds, benzyl(hydrogenated tallow alkyl)dimethyl, stearates, salts with bentonite rheological additive 121888-68-4 1-5 ethane, 1,1',1''-methylidenetris(oxy)-tris-ethyl orthoformate 122-51-0 1-5 1-5 1-5 1-5 1-5 1-5 1-5 1-5 1-5 1-5 acetic acid, butyl ester butyl acetate 123-86-4 5-10 10-20 10-20 10-20 10-20 5-10 5-10 5-10 5-10 5-10 5-10 benzene, dimethyl- xylene 1330-20-7 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 carbon black carbon black 1333-86-4 1-5 titanium oxide titanium dioxide 13463-67-7 20-30 20-30 5-10 5-10 1-5 10-20 5-10 2-propenoic acid, 2-methyl-, 2-hydroxyethyl ester, polymer with ethenylbenzene, 2-ethylhexyl 2-propeno and methyl 2-methyl-2-propenoate acrylic polymer 26916-05-2 10-20 10-20 10-20 10-20 10-20 10-20 10-20 10-20

2-naphthalenecarboxamide, 4- ((4(aminocarbonyl) phenyl)azo)-n-(2-ethoxyphenyl)-3-hydroxy-monazo red pigment 2786-76-7 5-10 hexane, 1,6-diisocyanato-, homopolymer aliphatic polyisocyanate 28182-81-2 90-95

Form: 379, Page 3 of 4, prepared 08/11/06 hindered amine light stabilizer 41556-26-7 1-5 1-5 c.i. pigment yellow 42 yellow iron oxide 51274-00-1 1-5 butanamide, 2-((2-methoxy-4-nitrophenyl)azo) -n-(2-methoxyphenyl)-3-oxo-pigment yellow 74 6358-31-2 1-5 5-10 1-5 solvent naphtha (petroleum), light aromatic light aromatic solvent naphtha

64742-95-6 1-5 butanamide, 2-((4-methoxy-2-nitrophenyl)azo))- n-(2-methoxyphenyl)-3-oxo-yellow pigment 6528-34-3 1-5 silica amorphous silica 7631-86-9 1-5 1-5 sulfuric acid, barium salt barium sulfate 7727-43-7 5-10 20-30 10-20 20-30 30-40 20-30 castor oil castor oil, raw 8001-79-4 1-5 1-5 1-5 5-10 1-5 1-5 1-5 5-10 1-5 stoddard solvent mineral spirits 8052-41-3 1-5 1-5 hexane, 1,6-diisocyanato- hexamethylene diisocyanate 822-06-0 .1-1.0 acetic acid, c6-8-branched alkyl esters oxo-heptyl acetate 90438-79-2 1-5 1-5 1-5 1-5 1-5 1-5 1-5 1-5 benzene,1,2,4-trimethyl- pseudocumene 95-63-6 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 .1-1.0 1-5 dispersant dispersant Sup. Conf. 1-5 substituted pyrrol substituted pyrrol Sup. Conf. 1-5 polyol reactive diluent polyol reactive diluent Sup. Conf. 5-10 orange pigment orange pigment Sup. Conf. 1-5 acrylic resin acrylic resin Sup. Conf. 10-20 30-40 40-50 10-20 10-20 10-20 10-20 10-20 10-20 10-20

Ingredients (Continued) Product Codes with % by Weight (ANSI Section 2)

Chemical Name Common Name CAS. No. 379B1000 379B3501 379B8557 379B9000 379B9200 379B9400 379B9500 379B9501 379B9502 379B9903 379C0910

Chemical Hazard Data (ANSI Sections 2, 8, 11, and 15)

ACGIH-TLV OSHA-PEL S.R.

Std. S2 S3 CCCommon Name CAS. No. 8-Hour TWA STEL C S 8-Hour TWA STEL C S H M N I O ethylbenzene 100-41-4 100 ppm 125 ppm not est. not est. 100 ppm not est. not est. not est. not est. n y y y n n y n methyl amyl ketone 110-43-0 50 ppm not est. not est. not est. 100 ppm not est. not est. not est. not est. n n n n n n n n rheological additive 121888-68-4 10 mg/m3 not est. not est. not est. 15 mg/m3 not est. not est. not est. not est. n n n n n n n n ethyl orthoformate 122-51-0 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n butyl acetate 123-86-4 150 ppm 200 ppm not est. not est. 150 ppm not est. not est. not est. not est. n n y n n n n n xylene 1330-20-7 100 ppm 150 ppm not est. not est. 100 ppm not est. not est. not est. not est. n y y y n n n n carbon black 1333-86-4 3.5 mg/m3 not est. not est. not est. 3.5 mg/m3 not est. not est. not est. not est. n n n n n n y n titanium dioxide 13463-67-7 10 mg/m3 not est. not est. not est. 10 mg/m3 not est. not est. not est. not est. n n n n n y y n acrylic polymer 26916-05-2 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n monazo red pigment 2786-76-7 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n aliphatic polyisocyanate 28182-81-2 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n light stabilizer 41556-26-7 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n yellow iron oxide 51274-00-1 5 mg/m3 not est. not est. not est. 10 mg/m3 not est. not est. not est. not est. n n n n n n n n pigment yellow 74 6358-31-2 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n light aromatic solvent naphtha 64742-95-6 not est. not est. not est. not est. 500x ppm not est. not est. not est. not est. n n n n n n n n yellow pigment 6528-34-3 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n amorphous silica 7631-86-9 10 mg/m3 not est. not est. not est. 6 mg/m3 not est. not est. not est. not est. n n n n n n n n barium sulfate 7727-43-7 10 mg/m3 not est. not est. not est. 5 mg/m3 not est. not est. not est. not est. n n n n n n n n castor oil, raw 8001-79-4 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n mineral spirits 8052-41-3 100 ppm not est. not est. not est. 500 ppm not est. not est. not est. not est. n n n n n n n n hexamethylene diisocyanate 822-06-0 0.005 ppm not est. not est. not est. not est. not est. not est. not est. not est. n y y y n n n n oxo-heptyl acetate 90438-79-2 not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n pseudocumene 95-63-6 25 ppm not est. not est. not est. not est. not est. not est. not est. not est. n y n n n n n n dispersant Sup. Conf. not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n

Footnotes: H=Hazardous Air Pollutant, M=Marine Pollutant C=Ceiling - Concentration that S=Skin - Additional exposure, n/a=not applicable ppm=parts per million S2=Sara Section 302 EHS P=Pollutant, S=Severe Pollutant should not be exceeded, over and above airborn exposure, not est=not established mg/m3=milligrams per cubic meter S3=Sara Section 313 Chemical Carcinogenicity Listed By:

even instantaneously. may result from skin absorption. CC=CERCLA Chemical Sup Conf=Supplier Confidential S.R.Std.=Supplier Recommended Standard N=NTP, I=IARC, O=OSHA, y=yes, n=no

Form: 379, Page 4 of 4, prepared 08/11/06 substituted pyrrol Sup. Conf. not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n polyol reactive diluent Sup. Conf. not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n orange pigment Sup. Conf. not est. not est. not est. not est. not est. not est. not est. not est. not est. n n n n n n n n

Chemical Hazard Data (Continued) (ANSI Sections 2, 8, 11, and 15)

ACGIH-TLV OSHA-PEL S.R.

Std. S2 S3 CCCommon Name CAS. No. 8-Hour TWA STEL C S 8-Hour TWA STEL C S H M N I O

Footnotes: H=Hazardous Air Pollutant, M=Marine Pollutant C=Ceiling - Concentration that S=Skin - Additional exposure, n/a=not applicable ppm=parts per million S2=Sara Section 302 EHS P=Pollutant, S=Severe Pollutant should not be exceeded, over and above airborn exposure, not est=not established mg/m3=milligrams per cubic meter S3=Sara Section 313 Chemical Carcinogenicity Listed By:

even instantaneously. may result from skin absorption. CC=CERCLA Chemical Sup Conf=Supplier Confidential S.R.Std.=Supplier Recommended Standard N=NTP, I=IARC, O=OSHA, y=yes, n=no