DDPM262101_Alter CP and NDI_Plans (03272026).pdf

A

3-

A

I B I C I D I E I F

Construct

Using metal studs, frame the new walls the full height from the floor to the second floor deck. Install 5/8 gypsum board to include all mud, tape, and texture to match existing finishes. Paint new partitions to match existing finishes. Install rubber cove base to match existing finishes. If paint does not match well on blended portions of wall, the entirety of the wall shall be painted until the seam can be hidden.

Install VCT match existing finishes in the wing. (AZrock, Shale Gray #V-866)

Install new carpet (Shaw Contract, Clear Tile Style# 59564, color Moonstone 62500).

Properly frame a penetration using metal studs. Install Credential window to allow for proper identification processing and handling within the mantrap. Above credential slot, install an impact rated, mesh reinforced 1 way window. Install trim around credential window if the credential window installed requires ii.

Remove sound deadening from walls, clean, texture and paint walls (Paint standard color is Sherwin-Williams SW1016 Silver Screen)

Install doors to match existing. All doors must be solid wood constructed and reinforced externally with a steel sheet cover to prevent removal of the door. They must protect to prevent removal each external pin, bolt, screw, or other fastening device. Each doorframe must be compatible with both the strength of the door and the adjoining wall construction.

Install doors to match existing in wing. Identified security measure not applicable to this door.

Install door alarm on door designated as emergency exit. The emergency exit door shall not have a handle or access from the hallway side and must only be able to be opened from the inside. Ensure door meets all sound proof requirements, and ensure replacement seal & door meet requirements.

Enclose space above drop ceiling. Using metal studs, properly frame the space above the false ceiling open the adjacent hallway to prevent access between the two spaces. Install double layer 5/8 gypsum board to include all mud and tape. Texture and paint are not required above drop ceiling.

Equip the outer and inner door to the standoff/entrapment area with a key lock on the exterior side of the door for emergency entry.

Install remote unlocking capability from the console for each mantrap door individually. Configure of the electronic locking doors must ensure only one door can open at any lime (to include remote unlocking from the consoles). In the event of failure, the locks must fail in the locked position and have a manual override for emergency egress. Manual override shall be mounted near the interior door of the mantrap to activate during egress. Install empty EMT conduit and empty comm box near location of remote unlocking function and electronically activated locks to enable future installation of a card entry system.

Remove and replace all cabinets, overhead cabinets, counters, and the sink in the new dimensions and configuration. Overhead cabinets will be installed above all identified lower cabinets, Cabinets must be approved by government.

Disassemble and dispose of the existing rack system and the attached studio lighting in the current studio (Rm 143). Repair any penetrations to drop ceiling.

INFO. ASSURANCE

I

( tFCI

G)

(3

ZS

ZS

ZS

ZS

G I H I I J I K I L

Electrical Install 20 AMP 120V receptacles and any peripherals 16" above finished floor as indicated on drawings

Install a 20 AMP 120V receptacle and any peripherals 72" above finished floor as indicated for a wall mounted TV or a phone box.

Install a 20 AMP 120V GFCI receptacle and any peripherals 12" above counter height.

Lighting for the man trap shall be operated by a switch and occupancy sensor. This switch will be mounted near the door of the man trap in room 143 so that an occupant of the man trap will not be able to turn the light off. The occupancy sensor inside of the mantrap will be configured so that if the switch is moved to "OFF", the lights will still come on.

Configure lighting to be operated by occupancy sensor that is to be positioned to capture movement through the entirety of the rooms.

Configure lighting to be operated by a manual switch. Install switches at indicated location.

Install Emergency Action Processing rotating light. Switch activated. Switch will be installed in the console room. Install sign displaying

"Classified Work in Progress" below rotating lights.

Install fire alanm strobes. All strobes must be tested and synchronized in timing.

Install light to match existing into the drop ceiling. The light is 24"x48". Properly configure the light to operate on the proper switch.

Install battery back up emergency lights and exit signs to illuminate the surrounding areas.

Install ¾" EMT conduit to above the drop ceiling, an empty comm box, a pull string, and any peripheral in new partition walls at indicated locations. The box will be installed 16" above finished floor.

Install ¾" EMT conduit to above the drop ceiling, a single empty comm box, a pull siring, and any peripheral in new partition walls at indicated locations. The box will be installed 72" above finished floor as indicated on drawings for a wall mounted TV in the teleconference room.

Install ¾" EMT conduit to above the drop ceiling, a single empty comm box, a pull string, and any peripheral in new partition walls at indicated locations. The box will be installed above door height for a security camera.

install¾" EMT conduit to above the drop ceiling, a single empty comm box, a pull string, and any peripheral in new partition walls at indicated locations. The box will be installed 48" from finished floor for wall mounted phones .

HVAC

Split off additional ducting from the current ducting and add 1 additional supply diffuser.

Install return grates into drop ceilings and constructed walls at the identified locations

Install a HVAC override button inside of the console room. This button will include any accessories or peripherals to allow ii to tum HVAC on for a designated amount of time without being scheduled.

I I □ I ZS

l ��i ZS�� ZSf � �

,. 15' ,L.._15'-10"

,, 16'-6"

00 � � �

0 0

I□

Comm

0 1- SZ@ --

FOYER

I B I C I D I E I F I G I H I I J I K I L

I M I N 0

General Notes

Modify and replace drop ceiling grid and tiles to accommodate new wall partitions.

Adjust, remove, or replace carpet tiles as needed to accommodate the new wall partitions to match existing carpet.

All flooring and ceilings will be a seamless transition with aligned tiles.

Any equipment (I.E. HVAC grills, light switches, light fixtures) that interfere with new wall construction shall be relocated.

Hardware must be Stanley/Best Lock Core compatible.

Drop ceiling may be temporarily taken down to allow for access. Any section that is removed must be reinstalled in its original condition.

All pre-existing lights will be configured to be operated by the control mechanism (Switch or occupancy sensor) for ii designated area.

All electrical shall be installed in¾" EMT conduit or greater in accordance with NEC.

All rooms shall have adequate fire suppression installed. Modify the current system to sufficiently encompass all newly constructed areas.

Balance the applicable HVAC system to correctly provide adequate climate control.

Install bars or applicable measures to any ducting or returns to allow no access into the secure space (the current Rm 143 & 144).

I M I N

Cl'.

0 (.)

- t"--bQN �;g�M U i::Q t-M d o ><"�

��r-__ 5;

c-€ � w '° uj O.,...., !.: � 5 � 00

:i: ii;

::;; f-

0 Cl 0 N (/) z Cl w □

a. a.

w

a. w Cl'. a.

a.

ii:

w Cl'.

_1-

QC/)

zO �a..

1-0

0� (l)Z o<( c::: � a..�

<( � 0� :::::>� (.9 fr zO _J w <(U

Zw �N

Offi 0� -(/) u...-f-w

<( � I-Ill z� c:::

I c::: � w -o >8 <( � ZzC/) ti 0- �3 o...J w;; I-� z 0 z ;;.: Ill

□ w :es: w > w Cl'.

::;; Cl'. a. □ □ w

Cl'. a.

z ii: w w z z w iii f-z

0 ...J co � 0 w f-

DRAWING SIZE:11X17

SPEC. NO.

SCALE: 3/16" = 1'

PROJECT NUMBER

DDPM262101

SHEET 1 OF 2

A-1

A I B I C I D I E I F I G I H I I I J I K I L I M I N 0

- t---bQN

�;g�M z U i::Q t-M 0 d o ><"� ti'.

��r-__ 5;

>- 0 c'€ � w z 10 10 '° uj O.,...., !.:

GENERAL

� 5 � 00 ::;; ::;;

:i: ii; f- ;;:0 C) HALL'w'AY 0 a:, N Cl) n 0 Install compressed air from Engine shops existing system to provide compressed airlines into the z w - - � room with proper fillings, filters, and regulators installed on the Northwest wall. Minimum pressure is C) w � 125 PSI. cii > w w

(2)

□ 0::

1 ,...�00 r

,...�FCI

Prime and paint the walls (Paint standard color is Sherwin-Williams SW1016 Silver Screen)

D

,... GFCI

Install eye wash station to include all pumping required. There is a water spigot plumbed to the room. 9 a.

l

The eye wash station may be source by a tee from this spigot. a.

(4) Remove the Jockey pump and peripherals to include but not limited to brackets, stands, and tanks. w

Demo, remove, and cap all lines that were previously used by the decommissioned AFFF system.

PANELS � A.. This includes the exhaust piping for the jockey pump >-

- a:, ..,. � a.

l Demo and remove existing ventilation fan from ceiling. Seal the penetration with a plate and insulate w

0::

0000000�0

,_, with rigid board insulation. This must be able to be removed and retrofitted for a future ventilation 8 a.

uu.. system. l!l /" r-..

I I Demo concrete and remove so that the floor is flush, flat, smooth, and finished across the entirety of

I '--V the floor. This includes both the AFFF storage tank pedestal, AFFF catchment, and the jockey pump

- pedestals. Removal of concrete and backfilling may be required to facilitate the finished floor -requirement. 0

Install 6" closed cell spray foam insulation to ceiling. Ensure the proper clearance is maintained CD

HANGAR AFFF CATCHMENT ENGINE SHOP "' between the foam and fire suppression nozzles. ::;;

t

6' HIGH CONCRETE 7 0::

(g) a.

Install epoxy floor coating on all floors in the NDI room. □ in Patch any damage to CMU walls. Install fire rated sealant to any penetration through the CMU walls. f-

15' w - -

0::

J□CKEYPUMP PEDESTAL/

a.

z

6 NDI HVAC 6

ti:

r-.. (\J w

/ w l

1 z

Install a properly sized Mini Split HVAC system to regulate and properly control the temperature. This z � 6' HIGH CONCRETE mini split is required to have humidity control capable of maintaining 60% or less relative humidity. z w

0 in

- The condenser will be wall mounted on the exterior wall of the NDI room. All power, control, and other tl peripherals to properly operate the system are required. a. <( ti: w u.. f-l!l/ r-.. (.)

Install an ERV (Energy Recovery Ventilator) system capable of 1.5 ACH. This system shall be Cl) z ' I I w

@ heat/cool & humidity capable. The intake and exhaust can be installed using the current louver system □ 0

� 5 'I' that is being plated and insulated. Installation will include all electrical and ducting. 5 st 9' > (.) "' w 0

Install an insulated plate on existing vents in the exterior wall and door to seal from exterior. This must 0:: ...J

AFFF PE□CSTAL/

@) be able to be removed and retrofitted for a future ventilation system.

0 ELECTRICAL

z

4 42' HIGH CONCRETE 4 �

>< 1--qpGFCI

Install 20 AMP GFCI 120V receptacle flush mounted at 18" from finished floor and all peripherals. 0� C/)0 Shall be installed inside properly sized EMT conduit.

0::: ti'. o z

- 24'

I Install a 20 AMP dedicated home run GFCI 120V receptacle flush mounted at 18" from finished floor

<( 0 Q_ I

0® sz ® ® i2 and all peripherals. Shall be installed inside properly sized EMT conduit. =>� 0� n G)

Install 480V 100 amp 3 phase receptacle and all peripherals. Shall be installed inside properly sized (9� zco IL

<( T""

I I EMT conduit. A 3 phase panel currently exists in the NDI room that will be able to be used. 3

...J w

<( i

� ID

G) Install a rotating warning light on the outside wall that will be operated by a switch mounted in the Zw � I interior. oa; 0�

- G) Demo and properly terminate the electrical hookup for the jockey pump

- I-� uo <( � 1-Z

6 Install¾" EMT conduit with a pull string from the hallway with an empty comm box 48" from the z� 0::: ::::i finished floor. 0::: � WU

2 2 -o >

CD

z

Cl) ti; 0 i3

�3 u £2

- - w w� !.:

I- z □

DRAWING SIZE:11X17

1 1 SPEC. NO.

SCALE: 1/4" = 1'

PROJECT NUMBER

DDPM262101

SHEET 2 OF 2

A I B I C I D I E I F I G I H I I I J I K I L I M I N 0 A-2