Data Sheet 5 Table drill.pdf

Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany www.bosch-pt.com

1 619 929 J54 (2011.10) PS / 222 UNI

PBD 40

de Originalbetriebsanleitung en Original instructions fr Notice originale es Manual original pt Manual original it Istruzioni originali nl Oorspronkelijke gebruiksaanwijzing da Original brugsanvisning sv Bruksanvisning i original no Original driftsinstruks fi Alkuperäiset ohjeet el Ðñùôüôõðï ïäçãéþí ÷ñÞóçò tr Orijinal işletme talimat� pl Instrukcja oryginalna cs Původní návod k používání sk Pôvodný návod na použitie hu Eredeti használati utasítás ru Îðèãèíàëüíîå ðóêîâîäñòâî ïî ýêñïëóàòàöèè uk Îðèã³íàëüíà ³íñòðóêö³ÿ ç åêñïëóàòàö³¿ ro Instrucţiuni originale bg Îðèãèíàëíà èíñòðóêöèÿ sr Originalno uputstvo za rad sl Izvirna navodila hr Originalne upute za rad et Algupärane kasutusjuhend lv Instrukcijas oriģinālvalodā lt Originali instrukcija

OBJ_BUCH-1183-004.book Page 1 Monday, October 24, 2011 11:35 AM

2 |

1 619 929 J54 | (24.10.11) Bosch Power Tools

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seite 9

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 17

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 25

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Página 33

Português. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Página 42

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 50

Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 58

Dansk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side 66

Svenska . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sida 73

Norsk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side 80

Suomi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sivu 87

ÅëëçíéêÜ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Óåëßäá 94

Türkçe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sayfa 103

Polski . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strona 110

Česky . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 119

Slovensky. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 126

Magyar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oldal 134

Ðóññêèé . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ñòðàíèöà 142

Óêðà¿íñüêà. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ñòîð³íêà 151

Română . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 159

Áúëãàðñêè . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ñòðàíèöà 167

Srpski . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 176

Slovensko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stran 183

Hrvatski . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stranica 191

Eesti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lehekülg 199

Latviešu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lappuse 206

Lietuviškai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Puslapis 214

OBJ_BUCH-1183-004.book Page 2 Monday, October 24, 2011 11:35 AM

| 3

Bosch Power Tools 1 619 929 J54 | (24.10.11)

PBD 40

OBJ_BUCH-1183-004.book Page 3 Monday, October 24, 2011 11:35 AM

4 |

OBJ_BUCH-1183-004.book Page 4 Monday, October 24, 2011 11:35 AM

| 5

B

A

M8 (4x)

M8 (4x)

OBJ_BUCH-1183-004.book Page 5 Monday, October 24, 2011 11:35 AM

6 |

E

D

C

OBJ_BUCH-1183-004.book Page 6 Monday, October 24, 2011 11:35 AM

| 7

HG

F2F1

32 1920

OBJ_BUCH-1183-004.book Page 7 Monday, October 24, 2011 11:35 AM

8 |

K

JI

34 34

OBJ_BUCH-1183-004.book Page 8 Monday, October 24, 2011 11:35 AM

English | 17

English

Safety Notes General Power Tool Safety Warnings

When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury in-cluding the following.

Read all these instructions before attempting to operate this product and save these instructions.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an exten-sion cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoid-able, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while op-erating power tools may result in serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal inju-ries.

Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or en-ergising power tools that have the switch on invites acci-dents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a ro-tating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewel-lery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

If devices are provided for the connection of dust ex-traction and collection facilities, ensure these are con-nected and properly used. Use of dust collection can re-duce dust-related hazards.

Power tool use and care Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment or bind-ing of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in ac-cordance with these instructions, taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a hazardous situation.

Service Have your power tool serviced by a qualified repair per-son using only identical replacement parts. This will en-sure that the safety of the power tool is maintained.

WARNING

OBJ_BUCH-1183-004.book Page 17 Monday, October 24, 2011 11:35 AM

18 | English

Safety Warnings for Drill Presses The power tool is provided with a warning label in Ger-man (marked with number 10 in the representation of the power tool on the graphics page).

Before putting into operation for the first time, attach the supplied sticker in your national language over the German text on the warning label.

Never make warning signs on the machine unrecognis-able.

Fasten the machine on a firm, level and horizontal sur-face. If the machine can slip off or wobbles, the application tool cannot be uniformly and securely guided.

Keep the working surface clean to the workpiece being worked. Sharp-edged drilling chips/swarf and objects can lead to injuries. Material mixtures are particularly danger-ous. Light-alloy dust can burn or explode.

Set the correct speed before beginning to work. The speed must be appropriate for the drilling diameter and the material being drilled. When the speed is set in-correctly, the application tool can become caught or jam in the workpiece.

Guide the application tool toward the workpiece only when switched on. Otherwise, there is danger of the ap-plication tool becoming caught or jamming in the work-piece, and the workpiece being dragged along. This can lead to injury.

Keep your hands out of the drilling area while the ma-chine is running. Danger of injury in case of contact with the application tool.

Never remove drilling chips/swarf from the drilling ar-ea while the machine is running. Always guide the motor unit to the idle position first, and then switch the machine off.

Do not remove forming drilling swarf/shavings with your bear hands. Danger of injury in particular through hot and sharp-edged metal swarf/shavings.

Break off long drilling swarf/shavings by interrupting the drilling procedure through brief reversing of the handwheel. Danger of injury from long drilling swarf/shav-ings.

Keep handles dry, clean, and free from oil and grease.

Greasy, oily handles are slippery causing loss of control.

Use clamping devices, the quick-clamping device or a machine vice (accessory) to clamp the workpiece. Do not drill workpieces that are too small to clamp. When holding the workpiece by hand, you cannot secure it suffi-ciently against being turned, and injure yourself.

Switch the machine off immediately when the applica-tion tool blocks. The application tool blocks when:

– the machine is subject to overload or

– when it jams or locks-up in the workpiece.

Do not touch the application tool directly after the working process until after it has cooled down. Applica-tion tools become very hot while working.

Check the cable regularly and have a damaged cable re-paired only through an authorised customer service agent for Bosch power tools. Replace damaged exten-sion cables. This will ensure that the safety of the power tool is maintained.

Store the machine in a safe manner when not being used. The storage location must be dry and lockable.

This prevents the machine from storage damage, and from being operated by untrained persons.

Do not direct the laser beam at persons or animals and do not stare into the laser beam yourself, not even from a distance. This power tool produces laser class 2 laser ra-diation according to EN 60825-1. This can lead to persons being blinded.

Do not replace the installed laser with another laser type. A laser that does not fit to this power tool could pose dangers for other persons.

Never leave the machine before it has come to a com-plete stop. Cutting tools that are still running can cause in-juries.

Never use the machine with a damaged cable. Do not touch the damaged cable and pull the mains plug when the cable is damaged while working. Damaged cables in-crease the risk of an electric shock.

Products sold in GB only: Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an author-ised customer service agent. The replacement plug should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains sock-et elsewhere.

Products sold in AUS and NZ only: Use a residual current de-vice (RCD) with a rated residual current of 30 mA or less.

Symbols The following symbols can be important for the operation of your power tool. Please memorise the symbols and their meanings. The correct interpretation of the symbols helps you operate the power tool better and more secure.

Symbols and their meaning Laser Radiation Do not stare into beam Class 2 laser product

OBJ_BUCH-1183-004.book Page 18 Monday, October 24, 2011 11:35 AM

English | 19

Product Description and Specifica-tions

Read all safety warnings and all instruc-tions. Failure to follow the warnings and in-structions may result in electric shock, fire and/or serious injury.

Intended Use In conjunction with the suitable application tools, the ma-chine is intended for drilling in wood, metal, and plastic.

Product Features The numbering of the components shown refers to the repre-sentation of the power tool on the graphic pages.

1 Base plate 2 Quick-clamping lever 3 Quick-clamping device 4 Drilling column 5 Rack 6 Speed diagram 7 Clamping lever of the height adjustment 8 Clamping lever of depth stop 9 Depth stop

10 Laser warning label 11 Handwheel 12 Motor unit 13 On/Off switch with Quick-Stop function 14 Display 15 Speed regulator 16 Keyless chuck 17 Tool bit * 18 Mounting holes 19 Parallel guide 20 Wing bolts of the parallel guide 21 Gear selector 22 Illumination and laser unit 23 Allen key (4 mm) 24 Fastening screw of the drilling column 25 Guide cog of the drilling column 26 Guide groove of the base plate 27 Securing ring 28 Holding ring 29 Clamping sleeve 30 Illumination button 31 Laser-cross button 32 Button for speed indication/drilling-depth indication 33 Zero-point button 34 Set screws for clamping force of the brake

*Accessories shown or described are not part of the standard de-livery scope of the product. A complete overview of accessories can be found in our accessories program.

Noise/Vibration Information Measured sound values determined according to EN 61029.

Typically the A-weighted noise levels of the product are:

Sound pressure level 77 dB(A); Sound power level 90 dB(A).

Uncertainty K =3 dB.

Wear hearing protection!

Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 61029:

ah <2.5 m/s2, K=1.5 m/s2.

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 61029 and may be used to compare one tool with

Wear safety goggles.

Do not dispose of power tools into house-hold waste!

Only for EC countries:

According to the European Guideline 2002/96/EC for Waste Electrical and Elec-tronic Equipment and its implementation into national right, power tools that are no longer usable must be collected sep-arately and disposed of in an environmentally correct man-ner.

On/Off switch

Switching Off

Starting the operation of the display

Drilling

Speed Diagram

The diagram provides the speed (rpm) to be set dependent on the drill bit diameter (Ø in mm) for the materials Steel and Aluminium.

Symbols and their meaning

OBJ_BUCH-1183-004.book Page 19 Monday, October 24, 2011 11:35 AM

20 | English another. It may be used for a preliminary assessment of expo-sure.

The declared vibration emission level represents the main ap-plications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly in-crease the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may sig-nificantly reduce the exposure level over the total working pe-riod.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work pat-terns.

Technical Data

Declaration of Conformity We declare under our sole responsibility that the product de-scribed under “Technical Data” is in conformity with the fol-lowing standards or standardization documents: EN 61029, EN 60825-1 according to the provisions of the directives

2011/65/EU, 2004/108/EC, 2006/42/EC.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9, D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen Leinfelden, 24.10.2011

Assembly Avoid unintentional starting of the machine. During as-sembly and for all work on the machine, the power plug must not be connected to the mains supply.

Delivery Scope Before starting the operation of the machine for the first time, check if all parts listed below have been supplied:

– Motor unit 12 with drilling column 4

– Base plate 1

– Quick-clamping device 3

– Parallel guide 19

– Allen key 23 Note: Check the power tool for possible damage.

Before further use of the machine, check that all protective devices are fully functional. Any lightly damaged parts must be carefully checked to ensure flawless operation of the tool.

All parts must be properly mounted and all conditions fulfilled that ensure faultless operation.

Damaged protective devices and parts must be immediately replaced by an authorised service centre.

Mounting Individual Components (see figure A) Before putting into operation for the first time, the machine must be assembled as follows:

– Slide the quick-clamping device 3 over the drilling column

4.

– Insert the drilling column 4 into the base plate 1 in such a manner that the guide cog 25 engages in the guide groove 26.

– Firmly tighten fastening screw 24 with Allen key 23.

Mounting to a Working Surface (see figure B) To ensure safe handling, the machine must be mounted on a level and stable surface (e. g., workbench) prior to using.

– Fasten the power tool with suitable screw fasteners to the working surface. The mounting holes 18 serve for this purpose.

Drill Press PBD 40 Article number 3 603 M07 0..

Rated power input W 710 No-load speed

– 1st gear

– 2nd gear min-1 min-1 200–850

600–2500 Laser type nm mW < 1

Laser class 2 Max. drilling dia.

– Steel

– Wood mm mm

Chuck clamping range mm 1.5–13 Drill stroke, max. mm 90 Total height mm 650 Size of base plate (Width x depth x height) mm 330 x 350 x 30 Weight according to EPTA-Procedure 01/2003 kg 11.2 Protection class /II The values given are valid for a nominal voltage [U] of 230 V. For differ-ent voltages and models for specific countries, these values can vary.

Please observe the article number on the type plate of your machine.

The trade names of the individual machines may vary.

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen Engineering Director

PT/ESI

OBJ_BUCH-1183-004.book Page 20 Monday, October 24, 2011 11:35 AM

English | 21

Dust/Chip Extraction Dusts from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one’s health. Touching or breathing-in the dusts can cause allergic reactions and/or lead to respiratory infections of the user or bystanders.

Certain dusts, such as oak or beech dust, are considered as carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Materials contain-ing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-rials to be worked.

Prevent dust accumulation at the workplace. Dusts can easily ignite.

Changing the Tool (see figure C) The motor unit 12 is provided ex works with a dual-sleeve key-less chuck 16.

Inserting

– Turn the securing ring 27 toward “UNLOCK”.

– Turn the clamping sleeve 29 in anticlockwise direction un-til the application tool 17 can be inserted.

– Completely insert the application tool 17, hold it in the tool holder and firmly turn clamping sleeve 29 by hand in clock-wise direction.

Firmly hold the holding ring 28 when doing this.

– Turn the securing ring 27 toward “LOCK” Note: When inserting drill bits with small diameters, set the tool holder beforehand approximately to the drill bit diame-ter. Otherwise, it is possible that the drill bit is not inserted centred.

Removing

– Turn the securing ring 27 toward “UNLOCK”.

– Turn clamping sleeve 29 in anticlockwise direction until the application tool 17 can be removed.

Operation Before any work on the machine itself, pull the mains plug.

After each adjustment on the machine, retighten the screws and clamping levers.

Preparing for Operation Illuminating the Work Area (see figure D) Provide for sufficient lighting of the direct working area.

– To activate the display 14, turn the On/Off switch 13 to position .

– Switch on the illumination unit 22 with button 30.

The indication “Light” is shown on display 14.

Correctly positioning the workpiece (see figure E) A laser cross indicates the exact drilling location.

– To activate the display 14, turn the On/Off switch 13 to position .

– Switch on the laser unit 22 with button 31.

The indication “Laser” is shown on display 14.

– Align your mark on the workpiece with the laser cross.

Clamping the Workpiece (see figures F1 – F2) To ensure optimum working safety, the workpiece must al-ways be firmly clamped.

Do not saw workpieces that are too small to clamp.

– Position the workpiece with help of the laser cross (see

“Correctly positioning the workpiece”, page 21).

– Loosen the quick-clamping lever 2 on the quick-clamping device 3.

– Allow the quick-clamping device to face against the work-piece. Turn the quick-clamping lever 2 in clockwise direc-tion until the workpiece is firmly clamped.

– After drilling, loosen quick-clamping lever 2 in anticlockwi-se direction.

– Turn the quick-clamping device 3 aside and remove the workpiece.

The parallel guide 19 is used for securing larger workpieces against turning.

– Loosen the wing bolts 20 of parallel guide 19 and insert the parallel guide into the grooves of base plate 1.

– Retighten the wing bolts again.

– Clamp the workpiece with the quick-clamping device 3.

Note: Use a machine vice (e.g. Bosch MS 80) to clamp small-er workpieces.

Adjusting the Height of the Motor Unit (see figure G) Do not adjust the height of the motor unit during opera-tion. Actuate clamping lever 7 only when the hand-wheel is in the starting position. This safety measure prevents possible injury.

The height of the motor unit 12 can be adjusted dependent on the length of the application tool and the size of the work-piece.

Note: After adjusting the height of the motor unit, the posi-tioning of the workpiece must be checked again with the laser cross. Realign the workpiece, if required.

When clamping lever 7 is open, a brake prevents the motor unit 12 from accidental lowering. Occasionally check the clamping force of the brake and readjust it as required (see “Adjusting the Brake of the Motor Unit”, page 23).

– Make sure that the handwheel 11 is in the starting posi-tion.

– Grasp the handwheel 11 with one hand and with the other hand, loosen clamping lever 7 in anticlockwise direction.

– Adjust the height of motor unit 12 with the handwheel ac-cording to the inserted application tool and height of the workpiece.

– Tighten clamping lever 7 again in clockwise direction.

OBJ_BUCH-1183-004.book Page 21 Monday, October 24, 2011 11:35 AM

22 | English

Note: Clamping lever 7 is indexed (adjustable), allowing it to be set to an ergonomically favourable and space-saving posi-tion.

With the clamping lever tightened, pull its lever away from the motor unit, turn it to the desired position and allow it to en-gage again.

Starting Operation Observe correct mains voltage! The voltage of the pow-er source must agree with the voltage specified on the nameplate of the machine. Power tools marked with 230 V can also be operated with 220 V.

Switching On

– To activate the display 14, turn the On/Off switch 13 to position .

– To start the machine, turn the On/Off switch 13 to position .

The speed can now be set (see “Adjusting the Speed”, page 22).

Switching Off

– To end the drilling, turn the On/Off switch 13 to position .

or

– To completely shut-off the machine, turn the On/Off switch 13 to position “0”.

Note: The machine is now de-energized. All current set-tings for speed and drilling depth are deleted.

Quick-Stop Function The Quick-Stop function enables swift switching off, e.g., when the application tool is jammed or locked-up in the work-piece.

– Briefly and quickly press the On/Off switch 13.

The machine and the display are switched off immediately.

Note: The machine is now de-energized. All current set-tings for speed and drilling depth are deleted.

– To restart the operation of the machine afterwards, the On/Off switch 13 must be reset to position “0”.

Afterwards, the machine can be switched on again (On/Off switch 13 in position ).

Restarting Protection The restarting protection prevents uncontrolled starting of the machine after a power failure (e.g., when the mains plug is pulled during operation).

– To restart the operation of the machine afterwards, the

On/Off switch 13 must be reset to position .

Afterwards, the machine can be switched on again (On/Off switch 13 in position ).

Temperature Dependent Overload Protection When using the machine as intended for, it cannot be subject to overload. In case of excessive loading or when exceeding the allowable operating temperature, the electronics switch the machine off until it is in the optimal operating-tempera-ture range again.

– To restart the operation of the machine afterwards, the On/Off switch 13 must be reset to position .

Afterwards, the machine can be switched on again (On/Off switch 13 in position ).

Adjusting the Speed Set the correct speed before beginning to work. The speed must be appropriate for the drilling diameter and the material being drilled. When the speed is set in-correctly, the application tool can become caught or jam in the workpiece.

When adjusting the appropriate speed, please refer to the speed diagram 6.

The diagram provides the speed (rpm) to be set dependent on the drill bit diameter (Ø in mm) for the materials Steel and Aluminium.

Gear Selection, Mechanical Actuate the gear selector 21 only when the machine is at a standstill.

Two speed ranges can be preselected with the gear selector 21.

1st gear:

Low speed range; for working with large drilling diameters.

2nd gear:

High speed range; For working with small drilling diameters.

– Set the gear selector 21 to the desired position.

Note: If the gear selector 21 cannot be turned to the stop, turn the drill chuck a little.

Electronic Speed Control (see figure H) With the speed regulator 15, the speed of the machine can be variably adjusted.

– To start the machine, turn the On/Off switch 13 to position .

– Press button 32 until “Speed” is indicated on the display.

– Turn the speed regulator 15 until the desired speed is indi-cated on display 14.

Working Advice General Information Before drilling, make sure that the quick-clamping device 3, the parallel guide 19 or the machine vice (accessory) are firm-ly clamped/tightened.

When the drill bit comes out of the workpiece, it can become caught or jam in the workpiece, and drag the workpiece along.

Therefore, reduce the feed at the end of the drilling phase.

If the application tool should become blocked, switch the ma-chine off. Allow the application tool and the workpiece to cool down. Remove the drilling chips/swarf. Determine the cause of the application tool's jam and correct it.

Special Notes on Drilling in Metal Centre-punch metal workpieces.

Pilot-drill when drilling diameters in excess of 10 mm.

To improve your work, use cutting oil (e.g. Bosch universal cutting oil) to cool the drilling.

OBJ_BUCH-1183-004.book Page 22 Monday, October 24, 2011 11:35 AM

English | 23

Position of the Operator Position yourself in front of the machine. This ensures a good view of the drilling location.

– Keep your hands and fingers away from the rotating appli-cation tool.

– Do not stand in front of the motor unit with crossed arms.

Drilling

– Place the workpiece on base plate 1.

– Adjust the height of the motor unit (see “Adjusting the

Height of the Motor Unit”, page 21).

– Align the workpiece with help of the laser cross (see “Cor-rectly positioning the workpiece”, page 21).

– Firmly clamp the workpiece (see “Clamping the Work-piece”, page 21).

– Adjust the appropriate speed (see “Adjusting the Speed”, page 22).

– Switch on the machine.

– For drilling, turn handwheel 11 with uniform feed until the desired drilling depth is reached (see “Indicating the Drill-ing Depth”, page 23).

– Once the desired drilling depth is reached, guide hand-wheel 11 back until the motor unit is back in the starting position.

– Switch the power tool off.

Indicating the Drilling Depth (see figure I) The current drilling depth can be indicated on the display 14.

– After the speed has been set, press button 32 until

“Depth” is indicated on the display.

– Adjust the height of the motor unit (see “Adjusting the

Height of the Motor Unit”, page 21).

– Carefully allow the drill-bit tip to slightly touch the workpie-ce.

– Press button 33 to set the zero point.

The indication “Reset” is shown on display 14.

– Drill with uniform feed until the desired drilling depth is in-dicated on the display.

Adjusting the Drilling Depth (see figure J) With the depth stop 9, the drilling depth t can be determined.

– Loosen clamping lever 8 in anticlockwise direction.

– Carry out a test drilling. When the desired drilling depth t is indicated on display 14 (see “Indicating the Drilling Depth”, page 23), retighten clamping lever 8 again.

For the following drillings, the drilling depth is limited to the setting t.

Transport

– When transporting the machine, hold it by the base plate

1.

The power tool should always be carried by two per-sons in order to avoid back injuries.

Maintenance and Service Maintenance and Cleaning

Before any work on the machine itself, pull the mains plug.

For safe and proper working, always keep the machine and ventilation slots clean.

If required, clean the drilling column 4 with a dry cloth and ap-ply a light coat of Bosch universal cutting oil (accessory).

If the replacement of the supply cord is necessary, this has to be done by Bosch or an authorized Bosch service agent in or-der to avoid a safety hazard.

If the machine should fail despite the care taken in manufac-turing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools.

In all correspondence and spare parts order, please always in-clude the 10-digit article number given on the type plate of the machine.

Adjusting the Brake of the Motor Unit (see figure K) The clamping force of the brake for the motor unit 12 can be readjusted.

Checking:

– The clamping force of the brake must securely hold the mo-tor unit in any position.

Adjusting:

– Turn both set screws 34 in anticlockwise direction with the supplied Allen key 23 to reduce the clamping force, or in-crease the clamping force by turning in clockwise direc-tion.

Tighten both set screws uniformly.

– Check if the desired clamping force has been reached.

After-sales Service and Customer Assistance Our after-sales service responds to your questions concern-ing maintenance and repair of your product as well as spare parts. Exploded views and information on spare parts can al-so be found under:

www.bosch-pt.com Our customer service representatives can answer your ques-tions concerning possible applications and adjustment of products and accessories.

Great Britain Robert Bosch Ltd. (B.S.C.)

P.O. Box 98 Broadwater Park North Orbital Road Denham Uxbridge

UB 9 5HJ

Tel. Service: +44 (0844) 736 0109 Fax: +44 (0844) 736 0146 E-Mail: boschservicecentre@bosch.com

OBJ_BUCH-1183-004.book Page 23 Monday, October 24, 2011 11:35 AM

24 | English

Ireland Origo Ltd.

Unit 23 Magna Drive Magna Business Park City West Dublin 24 Tel. Service: +353 (01) 4 66 67 00 Fax: +353 (01) 4 66 68 88

Australia, New Zealand and Pacific Islands Robert Bosch Australia Pty. Ltd.

Power Tools Locked Bag 66 Clayton South VIC 3169 Customer Contact Center Inside Australia:

Phone: +61 (01300) 307 044 Fax: +61 (01300) 307 045 Inside New Zealand:

Phone: +64 (0800) 543 353 Fax: +64 (0800) 428 570 Outside AU and NZ:

Phone: +61 (03) 9541 5555 www.bosch.com.au

Republic of South Africa Customer service Hotline: +27 (011) 6 51 96 00

Gauteng – BSC Service Centre 35 Roper Street, New Centre Johannesburg Tel.: +27 (011) 4 93 93 75 Fax: +27 (011) 4 93 01 26 E-Mail: bsctools@icon.co.za

KZN – BSC Service Centre Unit E, Almar Centre 143 Crompton Street Pinetown Tel.: +27 (031) 7 01 21 20 Fax: +27 (031) 7 01 24 46 E-Mail: bsc.dur@za.bosch.com

Western Cape – BSC Service Centre Democracy Way, Prosperity Park Milnerton Tel.: +27 (021) 5 51 25 77 Fax: +27 (021) 5 51 32 23 E-Mail: bsc@zsd.co.za

Bosch Headquarters Midrand, Gauteng Tel.: +27 (011) 6 51 96 00 Fax: +27 (011) 6 51 98 80 E-Mail: rbsa-hq.pts@za.bosch.com

Disposal The machine, accessories and packaging should be sorted for environmental-friendly recycling.

Do not dispose of power tools into household waste!

Only for EC countries:

According the European Guideline 2002/96/EC for Waste Electrical and Elec-tronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally cor-rect manner.

Subject to change without notice.

OBJ_BUCH-1183-004.book Page 24 Monday, October 24, 2011 11:35 AM