Attachment E - Plumbing Fixtures Information.pdf

THIS SPACE FOR ARCHITECT/ENGINEER APPROVAL

Due to continuing product improvement, the information contained in this document is subject to change without notice. All dimensions are ± 1/4" (6mm).

Laboratory Mixing Faucets

Rev. 021523

WATER SAVER RENEWABLE UNIT

FORGED BRASS

FOUR-ARM HANDLE

COLORED PLASTIC

INDEX DISC

FORGED BRASS

VALVE BODY

2-5/8" (67mm)

REMOVABLE SEVEN

3/8" IPS COUPLING

(152mm)

(25mm) 1"

SERRATION HOSE END

6"

3/8" IPS CONVERTIBLE

3/8" IPS "LOW FLOW"

LABORATORY VACUUM BREAKER

RIGID/SWING GOOSENECK

6-1/2" (165mm)

2-5/8" (67mm)

1-3/16"-18 MOUNTING SHANK

WITH LOCKNUT, (2) SET SCREWS

3/8" O.D. FLEXIBLE

(HOT WATER INLET)

COPPER TUBING

3/8" O.D. FLEXIBLE

(COLD WATER INLET)

COPPER TUBING

AND WASHER

(289mm)

11-3/8"

MEASUREMENTS MAY VARY ±1/4" (6mm).

13-1/2"

8-3/8" (213mm)

(343mm)

(67mm) 2-5/8"

(38mm) 1-1/2"

STAINLESS STEEL SEAT

UNIT WITH REPLACEABLE

WATER SAVER RENEWABLE

NOTES:

1. FIXTURE IS FULLY ASSEMBLED AND FACTORY

TESTED PRIOR TO SHIPMENT.

2. VACUUM BREAKER IS CERTIFIED TO COMPLY WITH

ASSE 1001.

3. FIXTURE IS CERTIFIED BY CSA INTERNATIONAL TO

COMPLY WITH ASME A112.18.1M AND CSA B125.1.

4. FIXTURE HAS A POLISHED CHROME PLATED FINISH.

051421-SCJ

R

USC

L414VB Laboratory Mixing Faucet, Deck Mounted, 6” Swing Vacuum Breaker Gooseneck

Attachment E - Plumbing Fixture Information lrc0014 Text Box EQT ADA Station (1) lrc0014 Text Box Fluids Lab (4) lrc0014 Approved is subject to change without notice. All dimensions are ± 1/4" (6mm).

Laboratory Mixing Faucets

Rev. 021523

L414VB-BH Laboratory Mixing Faucet, Deck Mounted, 6” Swing Vacuum Breaker Gooseneck, Wrist Blade Handles

WATER SAVER RENEWABLE UNIT

COLORED PLASTIC

INDEX DISC

FORGED BRASS

VALVE BODY

REMOVABLE SEVEN

3/8" IPS COUPLING

(152mm)

(25mm) 1"

SERRATION HOSE END

6"

LABORATORY VACUUM BREAKER

3/8" IPS "LOW FLOW"

RIGID/SWING GOOSENECK

3/8" IPS CONVERTIBLE

9-5/8" (244mm)

2-5/8" (67mm)

1-3/16"-18 MOUNTING SHANK

WITH LOCKNUT, (2) SET SCREWS

3/8" O.D. FLEXIBLE

(HOT WATER INLET)

COPPER TUBING

3/8" O.D. FLEXIBLE

(COLD WATER INLET)

COPPER TUBING

AND WASHER

(289mm)

11-3/8"

(44mm) Ø1-3/4"

MEASUREMENTS MAY VARY ±1/4" (6mm).

13-1/2"

8-3/8" (213mm)

(343mm)

(67mm) 2-5/8"

2-5/8" (67mm)

4" FORGED BRASS

WRIST BLADE HANDLE

(38mm) 1-1/2"

STAINLESS STEEL SEAT

UNIT WITH REPLACEABLE

WATER SAVER RENEWABLE

NOTES:

1. FIXTURE IS FULLY ASSEMBLED AND FACTORY

TESTED PRIOR TO SHIPMENT.

2. VACUUM BREAKER IS CERTIFIED TO COMPLY WITH

ASSE 1001.

3. FIXTURE IS CERTIFIED BY CSA INTERNATIONAL TO

COMPLY WITH ASME A112.18.1M AND CSA B125.1.

4. FIXTURE HAS A POLISHED CHROME PLATED FINISH.

051121-SCJ

R

USC

lrc0014 Accepted lrc0014 Text Box EQT ADA Station (1) lrc0014 Text Box Fluids Lab (1)

Eyewash / Drench Hose Units

Listed 8116. Units have been tested to and comply with

ANSI Z358.1-2014 and the Uniform Plumbing Code.

FF EW1022 Eyewash/Drench Hose Unit, Deck Mounted FF EW1022BP Eyewash/Drench Hose Unit, Deck Mounted, with Backflow Preventer

Application: Dual purpose eyewash/drench hose for deck mounting. Unit meets the provisions of ANSI Z358.1-2014 as both an eyewash and a drench hose. Unit may be left in the deck flange for use as a fixed eyewash, leaving user’s hands free. Alternatively, unit may be removed for use as a drench hose to rinse any part of user’s eyes, face or body.

Spray Head Assembly: Two GS-Plus™ spray heads mounted side-by-side. Each head has a “flip top” dust cover, internal flow control and filter to remove impurities from the water flow.

Valve: Forged brass squeeze valve activated by stainless steel lever handle. Valve has replaceable stainless steel seat for exceptional durability. Locking clip engages when handle is depressed, providing “hands free” operation. Valve stays open until locking clip is released.

Hose: 8’ reinforced PVC hose. 275 PSI maximum working pressure.

Mounting: Deck flange for countertop mounting. Flange has handle locator guide to position spray heads and handle facing forward at all times.

Backflow Preventer: In-line dual check backflow preventer installed on inlet of hose (EW1022BP only). ASSE 1024 Listed.

Note: Check with code authority for compliance with local plumbing code.

Supply: 3/8" NPT male swivel-type inlet.

Sign: ANSI-compliant identification sign.

Quality Assurance: Unit is completely assembled and water tested prior to shipment.

Available Options FF FSH 8 ft. flexible stainless steel hose in place of PVC hose.

FF �HG Undercounter hose guide bracket to prevent hose from tangling or binding.

FF VB In-line vacuum breaker for installation between valve and spray head.

FF ��AP3600 Thermostatic mixing valve precisely blends hot and cold water to deliver warm (tepid) water as required by ANSI Z358.1-2014. Refer to “Tempering Valves” section for complete technical and product selection information.

lrc0014 Accepted is subject to change without notice. All dimensions are ± 1/4" (6mm).

Listed 8116. Units have been tested to and comply with

ANSI Z358.1-2014 and the Uniform Plumbing Code.

Eyewash / Drench Hose Units

Emergency Eyewash/Drench Hose

Sign Included

FF EW1022 Eyewash/Drench Hose Unit, Deck Mounted FF EW1022BP Eyewash/Drench Hose Unit, Deck Mounted, with Backflow Preventer

REV. 071717

Ø2 3/8"

1 3/4" (44mm)

CHROME PLATED BRASS SQUEEZE

VALVE WITH REPLACEABLE

STAINLESS STEEL SEAT

LOCKING CLIP

NYLON HANDLE

NYLON DECK FLANGE WITH

HANDLE LOCATOR GUIDES

8' HIGH PRESSURE

REINFORCED PVC HOSE

3/8" NPT MALE

SWIVEL INLET

NOTES:

1. EACH GS-PLUS™ SPRAY HEAD HAS A "FLIP-TOP" DUST COVER,

INTERNAL FLOW CONTROL AND FILTER TO REMOVE IMPURITIES

FROM THE WATER FLOW.

2. HOSE SHOULD NOT BE USED IN APPLICATIONS WHERE WATER

PRESSURE EXCEEDS 90 PSI. HOSE SHOULD BE INSPECTED

PERIODICALLY FOR DETERIORATION.

(60mm)

(33mm)

1" IPS MOUNTING

SHANK WITH LOCKNUT

PROVIDE Ø1 3/8" (35mm)

HOLE IN DECK

STAINLESS STEEL

SQUEEZE HANDLE

WITH PLASTIC COVER

Ø1 5/16"

(2) GS-PLUS™

SPRAY HEADS 30°

2 1/4" (57mm)

10 1/8" (257mm)

Rev. 050219

Accepted

WaterSaver Faucet Co.

701 West Erie Street Chicago, IL 60654

wsflab.com

Measurements may vary ± 1/4".

rev 0215 ©2015 WaterSaver Faucet Co.

WITH LOCKNUT AND WASHER

3/8" IPS MOUNTING SHANK

(133mm) 5-1/4"

SERRATION HOSE END

REMOVABLE TEN

INDEX DISC

COLORED PLASTIC

2-1/16" (52mm)

VALVE BODY

FORGED BRASS

FOUR-ARM HANDLE

FORGED BRASS

STAINLESS STEEL SEAT

REPLACEABLE

3/8" NPT MALE INLET

MOLDED PTFE PACKING WITH

ADJUSTABLE PACKING NUT

NOTES:

MAXIMUM WORKING PRESSURE IS 150 PSI.

TESTED AT 250 PSI NITROGEN PRESSURE.

PURITY GASES IS REQUIRED.

2. FIXTURE IS FULLY ASSEMBLED AND FACTORY

3. SPECIFY IF CLEANING FOR OXYGEN AND HIGH

Ø1-5/8" (41mm)

(60mm) 2-3/8"

5-1/4" (133mm)

2-1/2" (64mm)

STAINLESS STEEL

REPLACEABLE FLOATING NEEDLE

1. VALVE IS CERTIFIED BY CSA INTERNATIONAL TO

COMPLY WITH ANSI Z21.15 AND CGA 9.1.

4. FIXTURE HAS A POLISHED CHROME PLATED FINISH.

C US

R

L2880-131WSA Needle Valve Assembly, Deck Mounted Single

Needle Valves lrc0014 Accepted