Attachment C - DLA Energy C QAP.pdf

ATKINS.RENRICK.L.10

24389320

Digitally signed by

ATKINS.RENRICK.L.1024389320

Date: 2025.03.11 15:58:35 -04'00'

ROSE.JAMAAL.R.10502

93366

Digitally signed by

ROSE.JAMAAL.R.1050293366

Date: 2025.03.11 14:30:04 -04'00'

BANISZEWSKI.DANIE

L.J.1287388698

Digitally signed by

BANISZEWSKI.DANIEL.J.1287388698

Date: 2025.03.13 08:11:54 -06'00'

DISTRIBUTION STATEMENT-A: APPROVED FOR PUBLIC RELEASE:DISTRIBUTION IS UNLIMITED

C16.08-1 TURBINE FUEL, AVIATION (JET A) (DLA ENERGY JAN 2025)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE PRODUCT CODE

9130-00-359-2026 Turbine Fuel, Aviation, Jet A JAA

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits.

(a) PRODUCT REQUIREMENTS. Jet A shall conform to the requirements of the latest version of ASTM D 1655, Standard Specification for Aviation Turbine Fuels, except as modified below, at the custody transfer point.

(b) SPECIFICATION MODIFICATIONS

(1) Microseparometer (MSEP).

(i) The following MSEP ratings apply in the presence of the additives listed below. Values apply at point of manufacture:

Jet-A Additive MSEP Rating, min.

Fuel System Icing Inhibitor (FSII) 85

Corrosion Inhibitor/Lubricity Improver (CI/LI) 80

Fuel System Icing Inhibitor (FSII) and Corrosion Inhibitor/Lubricity Improver (CI/LI)

(ii) MSEP shall be performed on unadditized Jet A that has a custody transfer point on the distribution system using, D7224 or D8073. If either method is not available testing may be conducted with D3948. Passing results (min 85) for D3948 will be considered acceptable. Test failures using D3948 shall be retested using D7224 or D8073. If fuel passes D7224 with a minimum limit of 85 or D8073 with a limit of 88, the fuel is acceptable with no further action.

(2) Fatty Acid Methyl Ester (FAME)

(i) For offerors that will be offering Jet A FOB Destination and/or Origin TT, which involves staging jet fuel at a terminal via a multi-product pipeline, a Certificate of Quality of the issue tank must include testing for FAME for Acceptance of the fuel. The Test method to be used is either IP 585, IP 583, IP 590, IP 599, or ASTM D 7797. The Referee Method is IP 585.

Current ASTM D1655 Jet A specification allows no more than 50 parts per million of FAME in jet fuel.

(c) ADDITIVES.

(1) Additives shall not be premixed with other additives before injection into the fuel.

(2) FUEL SYSTEM ICING INHIBITOR (FSII). When required by contract line item-

(i) FSII shall be added to the fuel and shall be Diethylene Glycol Monomethyl Ether (DIEGME) conforming to the latest version of ASTM D4171, Standard Specification for FSIIs, Type III or MIL-DTL-85470C, dated March 5, 2024, Inhibitor, Icing, Fuel System, High Flash, NATO Code Number S-1745.

(ii) FSII shall be added to the fuel so that the resulting concentration in the final blend is between 0.07% and 0.10% by volume.

(iii) When using the 20-ounce aerosol can to introduce FSII during over the wing refueling, determine the fuel quantity and calculate the amount of required additive. This additive shall be added gradually during filling to permit proper blending in the fuel. One can of aerosol additive will inhibit 180 gallons of fuel to 0.087 percent by volume. The use of aerosol FSII is not permitted for U.S. Navy aircraft refueling.

DISTRIBUTION STATEMENT-A: APPROVED FOR PUBLIC RELEASE:DISTRIBUTION IS UNLIMITED

(3) CORROSION INHIBITOR/LUBRICITY IMPROVER (CI/LI). When required by contract line item-

(i) The additive must conform to MIL-PRF-25017H with Amendment 1, dated August 4, 2011, revalidated May 25, 2021, Inhibitor, Corrosion/Lubricity Improver, Fuel Soluble (NATO S-1747), found in ASSIST and shall be listed in the electronic Qualified Products List (QPL)-25017, located in the Qualified Products Database (QPD) found at https://qpldocs.dla.mil/. The concentration of CI/LI added to the fuel must be between the minimum effective concentration and the maximum allowable concentration as listed for the CI/LI in QPL-25017.

(4) STATIC DISSIPATER ADDITIVE (SDA). When required by contract line item-

(i) SDA shall be added to the fuel and the conductivity limits of 50 to 600 picosiemens per meter (pS/m) at ambient temperature or 29.4oC (85oF), whichever is lower, unless otherwise directed by the procuring activity.

(5) METAL DEACTIVATOR (MDA). MDA shall not be used unless the supplier has obtained PRIOR written consent from the procuring activity.

(6) Product shall be homogeneously mixed. Until all aviation turbine fuel tanks are coated, it is acceptable to perform stratification tests in lieu of circulating tanks to achieve homogeneity.

(d) SYNTHETIC BLEND COMPONENT (SBC) and CO-HYDROPROCESSED SYNTHESIZED KEROSENE

(1) If a fuel containing an SBC or a co-hydroprocessed synthesized kerosene is being offered, notification shall be made to the contracting point of contact with submission of relevant details regarding the blend percentage and which Annex of ASTM D7566 for the synthetic blend component used, and which feedstocks and co-processing percentage for co-hydroprocessed synthesized kerosene. Only synthetic blend components approved in ASTM D7566, MIL-DTL-83133, and MIL-DTL-5624 and co-hydroprocessed synthesized kerosene produced from approved feedstock and percentage in ASTM D1655, MIL-DTL-83133, and MIL-DTL-5624 shall be acceptable to the government

(e) REPORTS. Refer to the MATERIAL INSPECTION AND RECEIVING REPORT (QAP E40.01) contract provision for reporting requirements.

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.14 FUEL, ETHANOL (PC&S) (DLA ENERGY DEC 2022)

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

(a) PRODUCT PERFORMANCE REQUIREMENTS. Product shall conform to the latest revision of ASTM D5798.

(b) BLENDING. Product shall be blended prior to delivery. Manifold blending at time of delivery and blending in the receipt tank is not permitted. The resultant blended product must meet all performance requirements specified in the contract.

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE

DLA ENERGY PRODUCT

CODE

9130-01-470-2024 85% Ethanol and 15% Gasoline E85

Signature

Prepared by:

Quality / Technical Support Office Approval:

Contracting Approval:

DEFENSE LOGISTICS AGENCY ENERGY Page 1 of 1

8725 JOHN J. KINGMAN ROAD

FORT BELVOIR, VIRGINIA 22060-6222

C16.23-2 COMMERCIAL MARINE GAS OIL MINIMUM REQUIREMENTS (DLA ENERGY SEPT 2024)

Product Classification

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE UNIT OF ISSUE

9140-01-313-7776 Marine Gas Oil MGO Gallons

9140-01-417-6843 Marine Gas Oil MGT Metric Tons

Supplies delivered under this contract, the Contractor shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. The Contractor shall also comply with all applicable International Agreements, Treaties, Conventions, and the like to which the United States is a party or with whose terms the receiving activity has otherwise agreed to comply, including but not limited to, the requirements of MARPOL 73/78 Annex VI Regulations 14 & 18. The Contractor shall be responsible for determining the existence of all such requirements prior to the time deliveries are made. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits.

The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that an International, Federal, State, and /or local environmental requirement, as identified above, is more stringent than a requirement contained in this contract, the Contractor shall deliver product(s) that complies with the more stringent requirement. Product(s) that fails to meet the more stringent requirement will be considered nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s). In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to the requirements of the latest revision of ISO 8217, Category ISO-F-DMA. In Accordance with Annex A of ISO 8217, the de minimis value of FAME shall be 0.5 volume %. Offeror/Supplier shall ensure product offered meets ISO 8217 de minimis FAME requirement. The following are additional requirements or approved modifications to specifications.

(a) SPECIFICATION MODIFICATIONS

(1) TESTING

(i) Hydrogen sulfide testing is not required

(ii) In addition to ISO 8217 approved sulfur tests, the following test methods are approved for Sulfur testing: ASTM D5453, D1266, D1552, D2622, D3120, D7039, or ISO16591. See section 6.3 of ISO 8217 for referee test method. For a total sulfur content of less than 0.05 mass % (500 ppm), the latest revision of ASTM D5453 is the recommended ASTM method.

(iii) The following test methods are approved for FAME testing per ISO 8217: IP 579 or ASTM D 7963. Test method EN 14078 is an equivalent test method for IP 579 and approved for FAME testing. See section 6.9 ISO 8217 for referee test method.

(iv) ASTM International Test Methods equivalent to ISO test methods referenced in ISO 8217, DMA testing, are approved for use.

(2) Environmental

(i) As of 01 JAN 2020, under the requirements listed in MARPOL 73/78 Annex VI Regulation 14, MGO-DMA (MGO & MGT) purchased under DLA Energy programs shall not exceed a revised maximum sulfur weight percent of 0.5 (% m/m). This requirement does not supersede more stringent federal, state, and local environmental requirements.

(ii) Per MARPOL 73/78 Annex VI Regulation 14, for ships operating in the most current emission control areas, the sulfur content of marine gas oil shall not exceed 0.10% mass (1000 ppm).

(iii) Per 40 CFR Section 80.510, the Marine Gas Oil sulfur requirement for all refineries and deliveries to ports within Continuous United States (CONUS) shall not exceed 0.0015 mass % (15 ppm) sulfur.

(b) ADDITIVES: Marine Gas Oil shall contain no black dye.

(c) OTHER REQUIREMENTS: Unless otherwise indicated by the Contractor in writing, prior to award, and in accordance with the

EVALUATION (SHIP’S BUNKERS) provision, the product offered shall fully meet the applicable specification. The supplier shall provide to the receiving vessel a “Statutory Sample” of at least 500 mL in volume, taken from the receiving vessel’s inlet bunker manifold, together with a Bunker Delivery Note (BDN). This sample will be sealed and carry a sample tag that provides the documentation required per MARPOL 73/78 Annex VI Regulation 18.

Signature

Prepared by:

Quality / Technical Support Office Approval:

C16.27 FUEL, BIODIESEL (B20) (DLA ENERGY OCT 2014)

In the event that a Federal, State, or local environmental requirement is more stringent than a specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. Offered product shall conform to the following requirements that define a fuel suitable for use in automotive diesel engines:

(a) PRODUCT COMPOSITIONAL AND PERFORMANCE REQUIREMENTS. The finished fuel shall conform to ASTM D7467, with a biodiesel blend percentage of 20 +/- 1 percent, with the exception that the biodiesel component, per ASTM D6751, shall be derived solely from either virgin or used vegetable oils. Biodiesel derived from animal fats or tallows shall not be used. Product classification is shown below:

MAXIMUM

DLA ENERGY PRODUCT SULFUR

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE CONTENT RED DYE

9140-01-470-4520 Grade Number B20 S15 BDI 15 µg/g (ppm) No

Suppliers of biodiesel blends shall be certified as either BQ-9000 Producers or BQ-9000 Marketers as set forth by standards adhering to The National Biodiesel Accreditation Program. Documentation of BQ-9000 certification shall be submitted at time of offer.

(b) BLENDING. Product shall be blended prior to delivery. Manifold blending at time of delivery and blending in the receipt tank is not permitted. The resultant blended product must meet all performance requirements specified in the contract.

(c) LOW TEMPERATURE OPERABILITY. For fuel supplied during the months of October through March, the low temperature performance of B20 biodiesel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X3 of ASTM D 7467.

(d) ENVIRONMENTAL PROTECTION AGENCY (EPA) REGISTRATION. B100 product must be EPA registered in accordance with 40 CFR Part 79, Registration of Fuels and Fuel Additives. The Contractor shall provide a copy of the EPA registration letter to the Contracting Officer at the time of offer.

Signature

Prepared by:

Quality / Technical Support Office Approval:

Prior approval as contract provision

Contracting Approval: Prior approval as contract provision

Legal Approval:

(Only required for E QAPs)

C16.38-2 Fuel Oil, Burner No. 2 S5000 (DLA ENERGY JUN 2021)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-00-247-4365 Fuel Oil, Burner No. 2 S5000 FS2

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

COUNTRY SPECIFICATION/GRADE

UNITED STATES, TERRITORIES and OTHER

LOCATIONS

ASTM D396 – GRADE 2

ITALY STD UNI CTI 6579 – GRADE B

GERMANY DIN 51603-1 – REGULAR HEATING OIL

UNITED KINGDOM BS 2869 – CLASS D

(a) SULFUR REQUIREMENT. The maximum allowable sulfur content for Burner Oil, Grade No. 2 S5000, shall be 0.50 weight percent or per State/local environmental requirements, whichever is more stringent.

(b) BLENDING REQUIREMENT. Blending of various compatible grades of burner oil to produce an intermediate grade is permitted, however, such blending shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the grade produced.

(c) DYE REQUIREMENT. Under United States regulations, fuel oil burner Grade No. 2 is required by 40 CFR Part 80 to contain a sufficient amount of the dye Solvent Red 164 so its presence is visually apparent. At or beyond terminal storage tanks, they are required by CFR Part 48 to contain the dye Solvent Red 164 at a concentration spectrally equivalent to 3.9 pounds per thousand barrels of the solid dye standard Solvent Red 26.

Signature

Prepared by:

Quality / Technical Support Office Approval:

Legal Approval:

(Only required for E QAPs)

DEFENSE LOGISTICS AGENCY ENERGY

FORT BELVOIR, VIRGINIA 22060-6222

C16.64-1 TURBINE FUEL, AVIATION (JP8) (INLAND EAST GULF/OFFSHORE) (ROCKY

MOUNTAIN/WEST) (WESTPAC) (ATL/EUR/MED) (PC&S) (DLA OCT ENERGY 2022)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-01-031-5816 Turbine Fuel, Aviation JP8

Aviation Turbine Fuel (JP8) shall conform to MIL-DTL-83133K, dated July 18, 2018 Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply.

Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited above. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment

(a) INCIDENTAL CONTAMINANTS. Particulate Matter and Fatty Acid Methyl Ester (FAME) content shall not exceed the limits outlined in Table IV of MIL-DTL-83133K dated July 18, 2018.

(b) SPECIFICATION MODIFICATIONS. Aviation Turbine Fuel (JP8) shall conform to MIL-DTL-83133K, dated July 18, 2018, modified as follows:

(1) TESTING

(i) FILTRATION TIME TESTING. For filtration time testing round upwards when reporting the filtration time, in minutes. For example, a filtration time of 10 minutes, 18 seconds, would be reported as 11 minutes.

(ii) MICROSEPAROMETER (MSEP) RATING LIMITS. See MIL-DTL-83133K, dated July 18, 2018, Table 1, Note 15 for MSEP test method selection criteria.

(A)Prior to initial production under this contract, the Contractor shall elect, on a one-time basis, which MSEP limit will be met for the balance of the contract. If the Contractor introduces fuel system icing inhibitor (FSII), corrosion inhibitor/lubricity improver (CI/LI), and/or static dissipater additive (SDA) after verification of product conformance with the MSEP requirement, the product is not required to meet a fixed limit on subsequent MSEP tests.

(B) If the Contractor elects to verify conformance with the MSEP requirement on a sample of product that does not contain FSII and CI/LI, an additional MSEP test shall be performed on a hand blend containing aviation turbine fuel, FSII, CI/LI, and antioxidant (AO) (AO only if required). The FSII shall be included in this hand blend at a concentration of 0.07 to 0.10 volume percent and the amount of the CI/LI included shall be within the concentration range specified in QPL-25017. The additional MSEP result of this hand blend is a REPORT ONLY requirement and shall be recorded corresponding to item 750X on the Standardized Report Form (see Attachment ). This result shall be recorded with an asterisk next to it, and with a footnote below, stating, “*MSEP result is a ‘Report Only’ requirement.

Original result of (fill in actual result) on product containing the following additives:

(fill in combination of additives).”

(iii) WORKMANSHIP. The workmanship criteria in MIL-DTL-83133K, dated July 18, 2018, paragraph 3.5, is revised to read, “At the custody transfer point, the finished fuel shall be clear and bright and visually free from undissolved water and particulate matter in accordance with the latest revisions of the approved test methods. ASTM D4176 or ASTM D6986, latest versions, may be used. In case of dispute as determined by sample results taken from the custody transfer point, the fuel shall be clear and bright at 21 degrees Celsius (°C) (70 degrees Fahrenheit [°F]) and shall contain no more than 1.0 mg/L of particulate matter. The sample in dispute shall be taken into an area where the sample is permitted to slowly equilibrate to 21°C (70°F); this shall apply to either D4176 or D6986.”

(A)ASTM D6986, latest revision, shall be the referee test method, see requirements, as drafted, in MIL-DTL- 83133K, dated July 18, 2018, section 3.5.

(B) For the latest revision of ASTM D 4176, Procedure 2, with a result of Rating 1, maximum. If the sample fails ASTM D4176 only because it contains visible particulate matter but meets the particulate matter requirements of 1.0 mg/L maximum as stated in MIL-DTL-83133K, Table IV, the workmanship

FORT BELVOIR, VIRGINIA 22060-6222

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED criteria is met.

(2) SPECIAL LOCATION REQUIREMENTS

(i)Rocky Mountain/West. Aviation fuel movement via the Chevron Pipeline (Utah, Idaho, or Washington state entry points) shall be limited to total sulfur content of 0.15 mass percent, maximum.

(ii) Alaska. For fuels refined in Alaska and delivered to Alaska locations, the total acid number shall be relaxed to

0.020 mg KOH/g maximum.

(c) ADDITIVES. Additives are required for deliveries of JP8 per MIL-DTL-83133K, dated July 18, 2018, unless addition is excluded by specific solicitation line item, applicable contract clause, or another contractual requirement.

(1) The CI/LI additive(s) used shall be of the type and concentration cited in QPL-25017. To locate this information: (1) Go to the Acquisition Streamlining and Standardization Information System (ASSIST) Quick Search website (URL http://quicksearch.dla.mil/), (2) type "QPL-25017" in the Document ID field, press the Search button, (3) click the QPL- 25017 search result under Document ID, (4) click the "Qualification" link under Overview [or the "View QPD data" link under Revision History], and (5) click the “MIL-PRF- 25017 CATEGORY 1” link under Govt Designation. The concentration range for each additive is listed under the “Source Notes” link under the far-right column of the table.

(2) Metal deactivator additive (MDA) shall not be used in JP8 unless the Contractor has obtained written consent from the Contracting Officer.

(3) The requirement for SDA (see MIL-DTL-83133K, dated July 18, 2018, paragraph 3.3.3 and fuel electrical conductivity requirement in Table I) shall not apply unless stated otherwise in the Schedule. Line injection of additives (FSII, CI/LI, and SDA) from shipping tank to delivery conveyance is permitted under the following conditions:

(i) A laboratory hand blend containing the required additives and aviation turbine fuel shall be tested to verify compliance with the specification.

(ii) Additives shall be proportionately injected throughout the entire loading process to ensure the additive is homogeneously blended into the product. The Contractor shall maintain records evidencing the homogeneous blending of all line-injected additives. Such records shall include meter or tank gauge readings or test results taken at intervals to provide confidence in the injection process.

(iii) When FSII is line injected, additive concentration shall be verified based on a representative sample from each shipping conveyance.

(iv) When SDA is line-injected, and insufficient time is available for the fuel to reach equilibrium before departure of the shipping conveyance, the Contractor shall verify conductivity level on a representative sample from each shipping conveyance. The receiving activity will measure the conductivity and advise DLA Energy if it does not meet the specification requirements.

(4) SPECIAL LOCATION REQUIREMENTS (ATL/EUR/MED ONLY)

(i) For deliveries to La Spezia, Italy, the CI/LI shall be 3.5 g/m3 above the minimum effective concentration as identified in QPL-25017. See paragraph (c)(1) above.

(ii) When AO is added to the hydrotreated portion of the finished product, the percentage of the blend that has been hydrotreated shall be reported.

(iii) The requirement for SDA (see MIL-DTL-83133K, dated July 18, 2018, paragraph 3.3.3 and fuel electrical conductivity requirement in Table I) shall not apply unless stated otherwise in the Schedule.

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

Signed by:

Date: October, 27, 2022 12:10

FORT BELVOIR, VIRGINIA 22060-6222

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-1 GASOLINE AUTOMOTIVE, UNLEADED, REGULAR (PC&S) (DLA ENERGY JUN 2017)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-00-148-7103 Gasoline, Regular Unleaded MUR

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically. Therefore, Contractors are expected to know the In-country, State, or Federal RVP requirements of areas being supplied and comply with those requirements.

GASOLINE AUTOMOTIVE, UNLEADED, REGULAR. Gasoline shall conform to each country specification as listed below:

COUNTRY SPECIFICATION NATIONAL STOCK NUMBER

AUSTRALIA FUEL STANDARD (PETROL) 2001

CANADA CAN/CGSB-3.5-2001

JAPAN JIS K 2202

PHILIPINES PNS/DOE QS 008:2012 9130-00-148-7103

MIDDLE EAST EN 228

ALL OTHER REGIONS ASTM D4814

LOCAL SPECIFICATIONS: In-country specifications not meeting the specification requirements in the chart above, but meet local requirements may also be submitted for review and approval.

(a) OCTANE REQUIREMENTS

(1) Unleaded regular automotive gasoline shall meet the Motor Octane Number (MON), Research Octane Number (RON) and/or

Anti-Knock Index (AKI) limits described in the specification listed for each country or the in-country requirements when applicable.

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with specification listed for each country requirements when applicable.

(b) OXYGENATE REQUIREMENTS.

(1) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(2) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-3 GASOLINE AUTOMOTIVE, UNLEADED, PREMIUM (MUP) (DLA ENERGY JUN 2017)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-00-148-7104 Gasoline, Premium Unleaded MUP

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically. Therefore, Contractors are expected to know the In-country, State, or Federal RVP requirements of areas being supplied and comply with those requirements.

GASOLINE AUTOMOTIVE, UNLEADED, PREMIUM. Gasoline shall conform to each countries specification as listed below:

COUNTRY SPECIFICATION NATIONAL STOCK NUMBER

AUSTRALIA FUEL STANDARD (PETROL) 2001

CANADA CAN/CGSB-3.5-2011

JAPAN JIS K 2202

PHILIPPINES PNS/DOE QS 008:2012 9130-00-148-7104

MIDDLE EAST EN 228

ALL OTHER REGIONS ASTM D4814

LOCAL SPECIFICATIONS: In-country specifications not meeting the specification requirements in the chart above, but meet local requirements may also be submitted for review and approval.

(a) OCTANE REQUIREMENTS

(1) Unleaded premium automotive gasoline shall meet the Motor Octane Number (MON), Research Octane Number (RON) and/or

Anti-Knock Index (AKI) limits described in the specification listed for each country or the in-country requirements when applicable.

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with specification listed for each country requirements when applicable.

(b) OXYGENATE REQUIREMENTS.

(1) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(2) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-7 GASOLINE, AUTOMOTIVE, UNLEADED (REFORMULATED GASOLINE) (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-01-388-4080 Reformulated Gasoline, Regular MRR

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

GASOLINE Product shall conform to the latest revision of ASTM D4814, as modified by the Environmental Protection Agency (EPA) requirements detailed in 40 CFR Part 80 - "Regulation of Fuels and Fuel Additives; Subpart D Reformulated Gasoline”. In part, these regulations mandate that the Phase II complex model reformulated gasoline must meet three emissions performance requirements when compared to the baseline gasoline marketed by a refiner in 1990: a 27 percent reduction in emissions of volatile organic compounds (VOCs), a 22 percent reduction in emissions of toxic pollutants, and a 7 percent reduction in emissions of oxides of nitrogen (NOx).

Further, Phase II complex model reformulated gasoline must meet two compositional requirements: 1.3 volume percent maximum benzene and no heavy metals (lead and manganese are examples of such metals).

The latest revision of specification ASTM D 4814 applies with the following specific requirements:

(1) OCTANE REQUIREMENTS.

(i) Reformulated gasoline shall meet the minimum AKI of 87.

(ii) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM D 4814.

(iii) For regular unleaded gasohol, in addition to an AKI of 87 minimum, the MON must not be less than 82.

(2) OXYGENATE REQUIREMENTS.

(i) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, suppliers shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(ii) Blending of permissible oxygenate into reformulated gasoline shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

MEREDITH.MICHAEL.E.1290973453 Digitally signed by MEREDITH.MICHAEL.E.1290973453 Date: 2016.12.22 15:08:13 -05'00'

BANISZEWSKI.DANIEL.J.1287388698 Digitally signed by BANISZEWSKI.DANIEL.J.1287388698 Date: 2016.12.28 08:56:47 -05'00'

PETERSON.DAVID.W.1074069483 Digitally signed by PETERSON.DAVID.W.1074069483 Date: 2017.01.06 13:37:50 -05'00'

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-10 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-01-524-5174 Grade Number 1-D S15 (ULSD) DS1

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to commercial specification ASTM D 975, Grade Number 1-D S15. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above.

(a) ADDITIVES.

(1) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(3) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(c) LOW TEMPERATURE OPERABILITY / CLOUD POINT REQUIRMENTS. The low temperature performance of diesel fuel shall be defined by the following property. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975.

Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

MEREDITH.MICHAEL.E.1290973453 Digitally signed by MEREDITH.MICHAEL.E.1290973453 Date: 2016.12.22 15:09:22 -05'00'

BANISZEWSKI.DANIEL.J.1287388698 Digitally signed by BANISZEWSKI.DANIEL.J.1287388698 Date: 2016.12.28 09:10:15 -05'00'

Date: 2017.01.06 16:49:52 -05'00'

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-11 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-01-524-0139 Grade Number 2-D S15 (ULSD) DS2

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited above. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to commercial specification ASTM D 975. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above. Maximum sulfur content shall be 0.0015 wt%.

(a) ADDITIVES.

(1) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(3) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(c) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975. Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

MEREDITH.MICHAEL.E.1290973453 Digitally signed by MEREDITH.MICHAEL.E.1290973453 Date: 2016.12.22 15:09:43 -05'00'

BANISZEWSKI.DANIEL.J.1287388698 Digitally signed by BANISZEWSKI.DANIEL.J.1287388698 Date: 2016.12.28 09:07:05 -05'00'

Date: 2017.01.06 16:51:05 -05'00'

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-12 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-01-541-6760 Grade Number 2-D S15 (ULSD) DSS

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to commercial specification ASTM D 975, Grade Number 2-D S15. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above

(a) ADDITIVES.

(1) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(3) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(c) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975. Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

(d) DYE REQUIREMENT. Product shall have addition of red dye. As a means of identification, the Internal Revenue Service (IRS) requires that a red dye, identified as Solvent Red 164 (alky derivatives of azo benzene azo naphthol), must be added to all nontaxable diesel and all nontaxable kerosene used for purposes other than military jet fuel. The definitions of diesel and kerosene are provided in 26 CFR Section 48.4081-1. The minimum concentration is provided in 40 CFR Part 80.

MEREDITH.MICHAEL.E.1290973453 Digitally signed by MEREDITH.MICHAEL.E.1290973453 Date: 2016.12.22 15:10:02 -05'00'

BANISZEWSKI.DANIEL.J.1287388698 Digitally signed by BANISZEWSKI.DANIEL.J.1287388698 Date: 2016.12.28 09:07:38 -05'00'

Date: 2017.01.06 16:52:23 -05'00'

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality/Technical Support Office Approval

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.69-13 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9140-01-541-6767 Grade Number 1-D S15 (ULSD) DSW

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below.