ATTACHMENT_7_-_FP001_-_FIRE_PROTECTION_SYMBOLS_LEGEND_NOTES_&_INDEX.pdf

FIRE PROTECTION GENERAL NOTES

1. FIRE PROTECTION SYSTEM TO COMPLY WITH NFPA 13 AND ALL APPLICABLE STATE CODES.

2. FINAL INSPECTION AND APPROVAL BY LOCAL FIRE MARSHAL AND ARCHITECT/ENGINEER.

3. SPRINKLER SHOP DRAWINGS AND MATERIAL SUBMITTALS SHALL BE SUBMITTED TO THE ARCHITECT/ENGINEER AND STATE

FIRE MARSHAL AND SHALL BE APPROVED PRIOR TO ANY INSTALLATION.

4. PIPE ROUTING SHOWN IS SCHEMATIC ONLY. IT IS THE RESPONSIBILITY OF THIS CONTRACTOR TO PROVIDE ANY ADDITIONAL

OFFSETS REQUIRED FOR PROPER INSTALLATION AND COORDINATION WITH OTHER TRADES.

5. PIPING IN AREAS WITH EXPOSED STRUCTURE SHALL BE INSTALLED AS HIGH AS POSSIBLE TO ALLOW THE OWNER MAXIMUM

USE OF THE SPACE.

6. REFER TO ARCHITECTURAL REFLECTED CEILING PLANS FOR CEILING DESCRIPTIONS AND HEIGHTS.

7. SPRINKLERS ARE TO BE COORDINATED WITH ALL DIFFUSERS, SPEAKERS, LIGHTING FIXTURES AND CEILING SYSTEMS.

SPACING OF SPRINKLERS SHALL BE IN ACCORDANCE WITH NFPA 13 AND THE LISTING OF THE SPRINKLER.

8. SPRINKLER LOCATIONS SHALL BE CENTERED IN THE TILE. PROVIDE ARMOVER OR SWING JOINT AS REQUIRED.

9. SPRINKLERS IN AREAS WITH EXPOSED STRUCTURE (OBSTRUCTED CONSTRUCTION) SHALL BE INSTALLED WITH DEFLECTOR 1" BELOW THE BOTTOM OF THE BEAM (MAXIMUM 22" BELOW ROOF DECK). EXPOSED BAR JOISTS THAT HAVE SPRAY-ON FIRE PROOFING THAT MAKES THE JOIST SOLID SHALL BE TREATED LIKE A BEAM WITH THE SPRINKLERS 1" BELOW THE BOTTOM OF

THE FIRE PROOFING.

10. SLEEVE AND/OR FIRESTOP ALL PENETRATIONS THROUGH RATED WALLS, CEILINGS, AND FLOORS WITH U/L LISTED ASSEMBLIES. FIRESTOP ASSEMBLIES SHALL BE EQUAL OR EXCEED THE RATING OF THE WALL, CEILING OR FLOOR. SEE

ARCHITECTURAL DRAWINGS FOR FINAL FINISHES.

11. PROVIDE ACCESS PANELS TO ALL VALVES ABOVE NON-ACCESSIBLE CEILINGS AND CHASES.

12. PROVIDE A PERMANENTLY ATTACHED NAME TAG TO THE RISER STATING THE REQUIRED DESIGN CRITERIA FOR EACH

HYDRAULICALLY-DESIGNED SYSTEM.

13. PROVIDE SPRINKLERS UNDERNEATH ALL EXPOSED DUCTWORK WHICH IS OVER 48" WIDE AND SPACE HEADS AROUND ALL OBSTRUCTIONS IN ACCORDANCE WITH NFPA 13. HEADS UNDER DUCTS ARE NOT INDICATED ON THE DRAWINGS BUT ARE REQUIRED AND SHALL BE PROVIDED IN ACCORDANCE WITH NFPA 13. SPRINKLER LOCATIONS UNDER DUCTWORK AND

AROUND OBSTRUCTIONS SHALL BE GOVERNED BY FINAL INSTALLED LOCATIONS.

14. PROVIDE SPRINKLERS AT THE TOP AND BOTTOM OF ALL STAIRWELLS AND AT THE LANDING OF EACH FLOOR THAT OPENS

INTO MORE THAN ONE FIRE ZONE.

15. PROVIDE SPRINKLER GUARDS ON ALL HEADS IN ELECTRIC ROOMS, TELEPHONE ROOMS, ELEVATOR ROOMS, ELEVATOR

SHAFTS AND ON ANY HEADS LESS THAN 7'-0" ABOVE THE FLOOR.

16. IF SYSTEM PRESSURE EXCEEDS 100 PSI, ALL HANGERS ON END HEADS IN PENDANT POSITION SHALL BE WITHIN 12" OF END

OF LINE IN ACCORDANCE WITH NFPA 13.

17. COORDINATE PIPING WITH ALL ELECTRICAL EQUIPMENT (PANELS, TRANSFORMERS, ETC.) PRIOR TO ANY INSTALLATION. DO NOT ROUTE ANY PIPING OVER ANY ELECTRICAL PANELS UNDER ANY CIRCUMSTANCES. ANY PIPING RUN OVER ELECTRICAL

SHALL BE REROUTED AT NO ADDITIONAL COST.

18. THE WATER MAIN TO BUILDING IS EXISTING WATER MAIN AND IS TO REMAIN.

19. THE LOCAL WATER SUPPLIER HAS NOT INDICATED THAT THE WATER SUPPLY COULD LEAD TO MICROBIAL INDUCED

CORROSION.

20. ALL VALVES SHALL BE PROVIDED WITH TAMPER SWITCHES AND ALL ZONES SHALL BE PROVIDED WITH FLOW SWITCHES

WIRED TO THE FIRE ALARM SYSTEM.

DESIGN CRITERIA

BLACK BOX THEATER 100 & STORAGE 100A :

OCCUPANCY CLASSIFICATION:

SYSTEM TYPE:

DESIGN DENSITY:

HYDRAULIC REMOTE AREA:

SPRINKLER ORIFICE SIZE:

DURATION OF SUPPLY:

MAX. COVERAGE/SPRINKLER HEAD:

HOSE STREAM ALLOWANCE:

STAIR 178, CONTROL ROOM 200/200B:

OCCUPANCY CLASSIFICATION:

SYSTEM TYPE:

DESIGN DENSITY:

HYDRAULIC REMOTE AREA:

SPRINKLER ORIFICE SIZE:

DURATION OF SUPPLY:

MAX. COVERAGE/SPRINKLER HEAD:

HOSE STREAM ALLOWANCE:

STANDPIPE:

SYSTEM DESCRIPTION:

REFERENCE PUBLICATIONS:

THE FOLLOWING PUBLICATIONS SHALL BE USED AS A REFERENCE FOR DESIGN OF THE FIRE SUPPRESSION SYSTEM ON THIS

PROJECT.

• FLORIDA FIRE PREVENTION CODE, 8th EDITION (2023)

• NFPA 13, STANDARD FOR THE INSTALLATION OF SPRINKLER SYSTEMS, 2019 EDITION

• NFPA 25, STANDARD FOR THE INSPECTION, TESTING, AND MAINTENANCE OF WATER-BASED FIRE PROTECTION

SYSTEMS, 2020 EDITION

SPRINKLER TYPE CRITERIA:

ALL SPRINKLERS IN CEILINGS TO HAVE SEMI-RECESSED SPRINKLERS (CHROME FINISH), AND SHALL BE RATED AT 165°F WITH A 5.6

K-FACTOR.

ALL SPRINKLERS IN AREAS WITH NO CEILINGS TO HAVE BRASS UPRIGHT SPRINKLERS, AND SHALL BE RATED AT 165° F WITH A 5.6

K-FACTOR. PROVIDE SPRINKLER HEAD WITH GUARDS IN MECHANICAL/ELECTRICAL ROOMS.

ORDINARY HAZZARY GROUP II

WET PIPE

.20 GPM/SQ.FT.

1,500 SQ. FT.

1/2"

60 - 90 MIN.

130 SQ. FT.

250 GPM

ORDINARY HAZARD GROUP I

WET PIPE

.15 GPM/SQ.FT.

1,500 SQ. FT.

1/2"

60 - 90 MIN.

130 SQ. FT.

250 GPM

EXISTING AUTOMATIC WET

FLORIDA ADMINISTRATIVE CODE CHAPTER 61G15-32 NOTES:

1. THE FIRE PROTECTION SYSTEM SCOPE OF WORK SHALL INCLUDE THE PREPARATION OF THE FIRE PROTECTION SYSTEM LAYOUT DOCUMENTS (WORKING PLANS). PROVIDE ALL EQUIPMENT, MATERIALS, COMPONENTS, ASSEMBLIES AND SUPPORT SYSTEMS REQUIRED, AS DESCRIBED, IN NFPA 13. THE FIRE PROTECTION CONTRACTOR SHALL CONDUCT A HYDRANT FLOW TEST AND PERFORM HYDRAULIC CALCULATIONS FOR PREPARATION OF THE FIRE PROTECTION SYSTEM

LAYOUT DOCUMENTS (WORKING PLANS).

2. THE FIRE PROTECTION DESIGN, CALCULATIONS, INSTALLATION AND THE ACCEPTANCE TESTING OF THE FIRE PROTECTION SYSTEM SHALL BE IN ACCORDANCE WITH NFPA 13 ; NFPA 24 ; THE FLORIDA BUILDING CODE, THE FLORIDA FIRE PREVENTION CODE AND ALL LOCAL CODES REQUIRED BY THE AUTHORITY HAVING JURISDICTION.

3. AREA OCCUPANCIES AND HAZARD CLASSIFICATIONS ARE LISTED IN THE DESIGN CRITERIA NOTE LOCATED ON THE

CONTRACT DOCUMENTS.

4. THE STRUCTURAL SUPPORTS AND OPENINGS FOR THE FIRE PROTECTION SYSTEM HAVE BEEN COORDINATED WITH THE

STRUCTURAL ENGINEER.

5. ALL SYSTEM CONTROL VALVES SHALL BE PROVIDED WITH TAMPER SWITCHES AND INTERFACE WITH THE FACP ON THE SUPERVISORY CIRCUIT, ALL FLOW SWITCHES SHALL INTERFACE WITH THE FACP ON THE ALARM CIRCUIT.

6. THE FIRE PROTECTION CONTRACTOR SHALL PREPARE AND PROVIDE FIRE PROTECTION SYSTEM LAYOUT DOCUMENTS AND HYDRAULIC CALCULATIONS. FIRE PROTECTION SYSTEM LAYOUT DOCUMENTS WITH HYDRAULIC CALCULATIONS SHALL BE SUBMITTED TO THE ARCHITECT/ENGINEER AND THE LOCAL AHJ FOR ACCEPTANCE PRIOR TO PERMITTING.

7. ALL FIRE PROTECTION EQUIPMENT AND COMPONENTS SHALL BE LISTED AND TESTED FOR FIRE PROTECTION USE. ALL FIRE PROTECTION EQUIPMENT AND COMPONENTS SHALL BE THE U.L. LISTED AND FM APPROVED.

8. THE WATER SUPPLY FOR THE FIRE PROTECTION SYSTEM HAS NOT SHOWN ANY EVIDENCE OF MICROBIAL INDUCED CORROSION (MIC). THE FIRE PROTECTION CONTRACTOR SHALL NOTIFY THE ARCHITECT/ENGINEER OF ANY EVIDENCE OF

MIC AND PROVIDE NECESSARY WATER TREATMENT AS NEED TO REDUCE OR ELIMINATE MIC.

FIRE PROTECTION LEGEND

OR - CONTROL VALVE W/ TAMPER SWITCH

SYMBOL DESCRIPTION

- CHECK VALVE

- FLOW SWITCH

- FIRE DEPARTMENT CONNECTION (WALL MOUNTED)

- FIRE DEPARTMENT CONNECTION (SIDEWALK SIAMESE)

- FIRE VALVE CABINET

- STANDPIPE WITH FIRE DEPARTMENT VALVE

- SPRINKLER DRAIN RISER

- COMBINATION RISER

- DRAIN VALVE

- REVISION REFERENCE

- DETAIL REFERENCE CALLOUT

FP3.01

DETAIL No.

SHEET SHOWN ON

- BACKFLOW PREVENTOR

- BACKFLOW PREVENTOR W/ FDC

X - HYDRAULIC NODE

FIRE PROTECTION SPECIFICATIONS

1.00 - GENERAL PROVISIONS

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

1.10

1.11

PROVIDE ALL LABOR, MATERIAL AND EQUIPMENT FOR A COMPLETE AND PROPERLY OPERATING FIRE PROTECTION

SYSTEM.

CODES AND STANDARDS: THE FIRE SPRINKLER PROTECTION SYSTEMS INSTALLATION, FLUSHING AND TESTING SHALL

COMPLY WITH THE REQUIREMENTS OF NFPA 13 AND ALL LOCAL CODES HAVING JURISDICTION.

PIPE THREAD PATTERN: ALL THREADS SHALL BE IN ACCORDANCE WITH LOCAL FIRE DEPARTMENT SPECIFICATIONS

AND NFPA 1963.

UL/FM APPROVAL: ALL EQUIPMENT, VALVES, COUPLINGS, HANGERS AND DEVICES SHALL BE APPROVED BY UNDERWRITERS' LABORATORY (UL) OR FACTORY MUTUAL (FM) FOR USE IN FIRE PROTECTION SERVICE.

LICENSURE: THE FIRE PROTECTION SYSTEMS SHALL BE INSTALLED BY A STATE CERTIFIED FIRE PROTECTION

CONTRACTOR.

ALL FIRE PROTECTION WORK SHALL BE DONE IN A NEAT AND WORKMAN-LIKE MANNER.

CONTRACTOR SHALL SECURE AND PAY FOR ALL PERMITS AND FEES, ETC., REQUIRED FOR THE EXECUTION OF THIS

WORK.

CONTRACTOR SHALL COORDINATE WORK WITH OTHER TRADES BEFORE FABRICATION OR INSTALLATION. OFFSETS AND/OR TRANSITIONS REQUIRED SHALL BE PROVIDED WITHOUT ADDITIONAL COST. CONTRACTOR SHALL COORDINATE

AND INSTALL WORK IN A TIMELY MANNER TO PREVENT DELAYS IN THE CONSTRUCTION.

CONTRACTOR SHALL BE RESPONSIBLE TO REPAIR OR REPLACE DAMAGED EQUIPMENT AND/OR MATERIAL.

PIPING SHOP DRAWINGS: SUBMIT 1/8" SCALE PIPING SHOP DRAWINGS. SHOP DRAWINGS SHALL INCLUDE SPRINKLER PIPING CUT LENGTHS, OFFSETS, FITTINGS AND DEVICES, ELEVATIONS, HANGER LOCATIONS, SPRINKLER HEAD COUNT BY TYPE, ELEVATION SECTIONS AND OTHER INSTALLATION INFORMATION. SUBMIT HYDRAULIC CALCULATIONS PROVING THE VIABILITY OF THE MOST HYDRAULICALLY-REMOTE AREAS OF THE PROJECT. INDICATE HYDRAULIC REFERENCE POINTS AND SUBMIT COMPUTER ANALYZED NODAL CALCULATIONS IN BOTH TABULAR AND GRAPHICAL FORMATS. HYDRAULIC IMBALANCE SHALL NOT EXCEED 0.01 GPM AT ANY NODE, AND WATER VELOCITY SHALL NOT EXCEED 20 FEET PER SECOND. DEMONSTRATE COMPLIANCE WITH THE REQUIREMENTS OF NFPA 13 REGARDING DENSITY, AREA OF APPLICATION, SELECTION OF HYDRAULICALLY-REMOTE AREAS, AND MAXIMUM COVERAGE PER

SPRINKLER.

COORDINATE ALL PIPE ROUTING WITH ALL OTHER TRADES PRIOR TO INSTALLATION. ROUTE ALL PIPING TO AVOID

DUCTWORK, PIPING, AND BUILDING STRUCTURE.

2.00 - BASIC MATERIALS AND METHODS

GENERAL: ONLY THE FOLLOWING MATERIALS DESIGNED FOR 175 PSIG CWP SHALL BE USED FOR FIRE PROTECTION

PIPING UNLESS SPECIFICALLY INDICATED OTHERWISE.

PIPE AND FITTINGS: ALL PIPING JOINED BY GROOVED COUPLINGS TO BE SCHEDULE 10 BLACK STEEL PIPE. ALL PIPING

JOINED BY THREADED JOINTS TO BE SCHEDULE 40 BLACK STEEL PIPE.

HANGERS: ALL HANGER SPACING SHALL COMPLY WITH THE REQUIREMENTS OF NFPA-13.

ACCESS PANELS: PROVIDE ACCESS PANELS TO ALL VALVES WITHIN CHASES OR ABOVE NON-ACCESSIBLE CEILINGS.

REFER TO ARCHITECTURAL DRAWINGS FOR CEILING TYPES.

HYDROSTATIC TESTS: ABOVE GROUND AND BELOW GROUND PIPING SYSTEMS SHALL BE HYDROSTATICALLY TESTED AT NOT LESS THAN 200 PSI PRESSURE, OR AT 50 PSI IN EXCESS OF THE MAXIMUM PRESSURE, WHICHEVER IS GREATER, FOR A PERIOD OF 2 HOURS. THE TEST PRESSURE SHALL BE READ FROM A GAUGE LOCATED AT THE LOW ELEVATION POINT OF THE INDIVIDUAL SYSTEM OR PORTION OF THE SYSTEM BEING TESTED. THE SPRINKLER PIPING SHALL NOT HAVE LEAKAGE EXCEEDING THE AMOUNTS SPECIFIED IN NFPA 24. LEAKAGE QUANTITIES SHALL BE DETERMINED BY PUMPING AT THE SPECIFIED TEST PRESSURE FROM A CALIBRATED CONTAINER. REPAIR LEAKING JOINTS AND RETEST AS NECESSARY UNTIL ALL SYSTEMS HAVE BEEN TESTED. TEST THE PIPING BETWEEN THE CHECK VALVE IN THE FIRE DEPARTMENT INLET PIPE AND THE OUTSIDE CONNECTION THE SAME AS THE BALANCE OF THE SYSTEM.

2.1

2.2

2.3

2.4

2.5

3.00 - FIRE PROTECTION VALVES AND ACCESSORIES

BUTTERFLY TYPE ISOLATION, 2-1/2 INCH AND LARGER: ISOLATION VALVES 2-1/2 INCH AND LARGER SHALL BE CAST IRON BODY BUTTERFLY VALVES WITH THE VALVE SIZE, PRESSURE RATING, MANUFACTURER AND "UL" AND "FM" CAST INTO THE BODY. VALVE SHALL HAVE BRONZE OR CAST IRON DISC, NEOPRENE DISC LINER, CAST IRON HANDWHEEL WITH DISC POSITION INDICATOR, INTEGRAL TAMPER SWITCH, 175 PSIG CWP WORKING PRESSURE, 350 PSIG CWP TEST

PRESSURE, AND FLANGED OR GROOVED CONNECTIONS - GRINNELL 8000 FP OR EQUAL.

FLOW SWITCH: PROVIDE AN ELECTRIC FLOW SWITCH WHERE INDICATED OR REQUIRED. FLOW SHALL BE SENSED BY AN IMMERSION PADDLE, WITH AN ADJUSTABLE RETARD SETTING FROM 0 TO 70 SECONDS TO MINIMIZE FALSE ALARMS.

FLOW SWITCH SHALL HAVE 2 SEPARATE SINGLE POLE, DOUBLE THROW MICROSWITCHES TO ACTIVATE A FLOW ALARM, OR TO INDICATE A TROUBLE SIGNAL IF THE FLOW SWITCH HOUSING IS TAMPERED. FLOW ALARM SHALL BE AUTOMATICALLY RESETTING. PROVIDE CLAMP-ON HOUSING TO SECURE UNIT TO PIPE, OR THREADED CONNECTION

FOR TEE FITTING - POTTER ELECTRIC SIGNAL CO. VSR-S.

3.1

3.2

FIRE PROTECTION FLOW TEST DATA

STATIC HYDRANT

STATIC - 74 PSI

RESIDUAL - 65 PSI

FLOW HYDRANT

1260 GPM

DATE - 05-10-2024

TIME - 7:45AM

LOCATION - HYDRANT #3 - #P12298

TEST CONDUCTED BY - FARRELL FIRE PROTECTION, LLC (ROBERT FARRELL #20815200012011)

STATIC HYDRANT

STATIC - 77 PSI

RESIDUAL - 68 PSI

FLOW HYDRANT

1350 GPM

DATE - 05-10-2024

TIME - 7:45AM

LOCATION - HYDRANT #4 - #P10676

GAGE

INSPECTOR'S TEST

FLOW SWITCH

GROOVED BUTTERFLY

W/TAMPER SWITCH

PIPE TO EXTERIOR(SEE PLANS)

GROOVED CHECK

TOP BEAM CLAMP

(U.L. LISTED OR F.M. APPROVED)

PIPE HANGER RING

(U.L. LISTED OR F.M. APPROVED)

ALL THREAD ROD

CONCRETE FASTENER

(U.L. LISTED OR F.M. APPROVED)

PIPE HANGER RING

(U.L. LISTED OR F.M. APPROVED)

ALL THREAD ROD

This item has been digitally signed and sealed by Francis M. Robertson, PE, on the date adjacent to the seal.

Printed copies of this document are not considered signed and sealed and the signature must be verified on any electronic copies.

255 S. Orange Avenue Suite 1600

Orlando, FL 32801 P 407.841.9050 www.tlc-engineers.com

© Copyright 2019 TLC Engineering Solutions, Inc.

TLC Project No. :

COA 15

Seal

Drawing No.:

Scale:

Revisions:

Drawing Title:

Approved By:

Issue Date:

Project No.:

Drawn By:

Consultants:

124060

As indicated

/2 /2

:0

:2

P M

C U s e rs \k o h n e n .b a rr y \O n e D ri v e

T L C

E n g in e e ri n g S o lu ti o n s \D o c u m e n ts \1

E A

S T

M

E P

R k o h n e n .b a rr y tl c -e n g

.c o m .r v t

V A

L E

N C

IA

C

O L L E

G E

B

L A

C K

B O

X E

A S

T B

U

IL

D

IN

G

N o rt h E c o n lo c k h a tc h e e

T ra il, O rl a n d o

124060

10-25-2024

DEP

KFB

FIRE PROTECTION

SYMBOLS, LEGEND,

NOTES AND INDEX

FP001

FIRE PROTECTION DRAWING INDEX

SHEET DESCRIPTION

FP001 FIRE PROTECTION SYMBOLS, LEGEND, NOTES AND INDEX

FP101 LEVEL 01 - FIRE PROTECTION

FP301 ENLARGED - FIRE PROTECTION

No Scale

SPRINKLER ZONE VALVE - WET PIPE SYSTEM

A

No Scale

HANGER - STEEL

B

No Scale

HANGER - CONCRETE

C

No. Date Description

10-25-2024 PERMIT / BID SET

Frank.Robertson Date 10/25/2024