Asbestos and Lead Report May 24th 2023.pdf

LIMITED HAZARDOUS

MATERIALS SURVEY

REPORT

SYR VOR Facility FAA – Roof-Mounted Teepee Replacement Project

Syracuse Hancock International Airport 1000 Colonel Eileen Collins Boulevard, Syracuse, NY 13212

Prepared for:

Ms. Caitlin (Dixon) Escorcia Safety Engineer

Engineering Services, AJW-2E16E

Federal Aviation Administration 800 Independence Avenue SW

Washington, DC 20591

Report Date: May 24, 2023

Prepared By:

4747 North 7th Street, Suite 422 Phoenix, AZ 85014

TRC Project: 545895

TABLE OF CONTENTS

EXECUTIVE SUMMARY ............................................................................................................. i

INTRODUCTION

BACKGROUND

Asbestos-Containing Materials

Asbestos Bulk Sampling Procedures

Paint Chip Sampling

Laboratory Analysis

FINDINGS

Negative Materials (No Asbestos Detected)

Paint Chip Sampling Results

RECOMMENDATIONS

DISCLAIMER

Appendices

Appendix A – Sample Location Diagram(s)

Appendix B – Representative Photographs

Appendix C – Laboratory Results and Chain of Custody

Appendix D – Certification(s)

Limited Hazardous Materials Survey Report May 24, 2023 SYR VOR Facility TRC Project: 545895

- i -

EXECUTIVE SUMMARY

The Federal Aviation Administration (FAA) contracted TRC Environmental Corporation (TRC) to conduct a limited scope hazardous materials survey of the roof-mounted teepee structure and adjoining materials at the very high frequency omnirange station (VOR) facility at the Syracuse Hancock Internation Airport (SYR) in Syracuse, New York. The survey activities were initiated on April 28, 2023, by Dmitriy Khimich, a New York State Department of Labor Asbestos Inspector and United States Environmental Protection Agency Lead Risk Assessor.

Asbestos-Containing Materials

Laboratory results of the bulk sampling indicated that asbestos was present in the black tar sealant between the flashing and roof deck, the black tar sealant between the joints of the outermost layer of flashing, and the white caulking around the roof-mounted teepee structure. The remaining samples analyzed by the laboratory based on the PLM and TEM methods were negative for asbestos. Any materials uncovered during renovation or demolition activities that are not addressed in this survey report, or presumed asbestos-containing materials (PACM), must be sampled by an accredited asbestos inspector and/or investigator prior to any disturbance, or they must be treated as asbestos-containing materials (ACM).

Lead-Containing Paint Sampling Results

Laboratory results of the paint chip sampling indicated that lead was present above the reporting limits in six (6) of the six (6) samples that were collected and analyzed. Lead-based paint (LBP) is defined as paint containing greater than or equal to 0.5 percent lead by weight (≥0.5%) or greater than or equal to 5,000 parts per million (≥5,000 ppm). Any paint containing less than 0.5% by weight (<0.5%), but greater than the laboratory detection limit is considered to be lead-containing paint (LCP). For any paint in which lead was detected, TRC recommends that any renovation activities that may disturb painted surfaces be conducted according to the Occupational Safety and Heath Administration (OSHA) requirements regarding lead in construction (29 CFR 1926.62).

- 1 -

INTRODUCTION

The Federal Aviation Administration (FAA) contracted TRC Environmental Corporation (TRC) to conduct a limited scope hazardous materials survey of the roof-mounted teepee structure and adjoining materials at the very high frequency omnirange station (VOR) facility at the Syracuse Hancock Internation Airport (SYR) in Syracuse, New York. The survey activities were initiated on April 28, 2023, by Dmitriy Khimich, a New York State Department of Labor Asbestos Inspector and United States Environmental Protection Agency Lead Risk Assessor.

BACKGROUND

Asbestos-Containing Materials

The Occupational Safety and Health Administration (OSHA) defines asbestos-containing material(s) (ACM) as any material containing more than one percent (>1%) asbestos.

The U.S. Environmental Protection Agency (EPA) defines ACM as follows:

1. Friable asbestos-containing material (ACM) is defined by the Asbestos NESHAP as any material containing more than one percent (>1%) asbestos as determined using the method specified in Appendix A, Subpart F, 40 CFR Part 763, Section 1, Polarized Light Microscopy (PLM), that, when dry, can be crumbled, pulverized or reduced to powder by hand pressure.

2. Nonfriable ACM is any material containing more than one percent (>1%) asbestos as determined using the PLM method that, when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure. The EPA further defines two categories of nonfriable

ACM:

a. Category I (Cat I) - Category I nonfriable ACM is any asbestos-containing packing, gasket, resilient floor covering or asphalt roofing product which contains more than one percent (>1%) asbestos as determined using PLM according to the method specified in Appendix A, Subpart F, 40 CFR Part 763, and

b. Category II (Cat II) - Category II nonfriable ACM is any material, excluding Category I nonfriable ACM, containing more than one percent (>1%) asbestos as determined using PLM according to the methods specified in Appendix A, Subpart F, 40 CFR Part 763 that, when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure.

3. Regulated Asbestos-Containing Material (RACM) is (a) friable asbestos material, (b) Category I nonfriable ACM that has become friable, (c) Category I nonfriable ACM that will be or has been subjected to sanding, grinding, cutting or abrading, or (d) Category II nonfriable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the material in the course of demolition or renovation operations.

Asbestos Bulk Sampling Procedures

The survey was conducted in accordance with the sample collection protocols established in Environmental Protection Agency (EPA) Asbestos Hazard Emergency Response Act (AHERA)

- 2 -

40 CFR Part 763, Subpart E, National Emissions Standards for Hazardous Air Pollutants (NESHAP) 40 CFR Part 61, Subpart M, and applicable state and local regulations. A summary of survey activities is provided below.

Survey activities began with visual observation of the project area to identify homogeneous areas of suspect ACM. A homogeneous area consists of building materials that appear similar throughout in terms of color and texture that does not extend to other buildings. Visual assessments were conducted in accessible areas of the building. Building materials identified as glass, wood or metal were not considered suspect ACM.

A physical assessment of each homogeneous area of suspect ACM was conducted to assess the friability and condition of the materials. Friability was assessed by physically touching suspect materials.

Based on results of the visual observation, bulk samples of suspect ACM were collected in accordance with AHERA, NYSDOL, and/or NYCDEP protocols. Samples of suspect materials were collected in each homogeneous area. Bulk samples were collected using wet methods as applicable to reduce the potential for fiber release. Samples were placed in sealable containers and labeled with unique sample numbers using an indelible marker.

Field information was organized as per the AHERA concept of homogenous area. That is, suspect ACM with similar age, appearance, and texture was grouped together, sampled, and assessed for condition.

Bulk samples of suspect ACM were analyzed by Polarized Light Microscopy (PLM) with dispersion staining, as described in 40 CFR Part 763 and the National Emissions Standard for Hazardous Air Pollutants (NESHAP).

The New York State Department of Health revised the PLM Stratified Point Counting Method. The new method, "Polarized Light Microscopy Methods for Identifying and Quantitating Asbestos in Bulk Samples" can be found as item 198.1 in the ELAP Certification manual. The State of New York ELAP has determined that analysis of non-friable organically bound materials (NOB's) is not reliably performed by PLM. Therefore, if PLM yields negative results for a non-friable material, it must be confirmed by Transmission Electron Microscopy (TEM).

All samples were initially analyzed by Polarized Light Microscopy. Samples which yielded a negative PLM result, and which are classified as a "non-friable" organically bound material were then reanalyzed utilizing Transmission Electron Microscopy (TEM) methodology.

As per the April 1, 2011 ELAP directive, Item Numbers 198.6/198.4, ceiling tiles with cellulose must now also be confirmed non-ACM via TEM analysis.

As per the July 9, 2013 ELAP directive, for thermal system insulation (TSI) or other presumed ACM (PACM) or miscellaneous suspect ACM which contains 10% vermiculite or less, ELAP method 198.1 can be used to determine the asbestos content of the material. Where TSI or other PACM or miscellaneous suspect ACM contain greater than 10% vermiculite, method 198.6 may be used to evaluate the asbestos content of the material; provided, however, that any test results using this method must be reported with the following conspicuous disclaimer: "This method does not remove vermiculite and may underestimate the level of asbestos present in a sample containing greater than 10% vermiculite."

- 3 -

As per the July 22, 2014 ELAP directive, item numbers 198.6/198.1, sprayed-on fireproofing (SOFV) must now also be analyzed for vermiculite content via ELAP method for SOF-V 198.8 or LAB.055.1, effective November 1, 2014.

In addition, as per the May 6, 2016 ELAP directive, surfacing materials analyzed via items 198.1 or 198.6, as applicable, which contain any amount of vermiculite, must be analyzed by either item

198.8 or LAB.055.1 to confirm asbestos concentration. Per ELAP, negative results for surfacing materials via 198.8 or LAB.055.1 can be reported without any attached disclaimers underestimating the actual asbestos concentrations.

All asbestos bulk samples were submitted under proper chain-of-custody (COC) documentation to the laboratory. Bulk samples were analyzed by PLM utilizing the EPA's Method for the Determination of Asbestos in Bulk Building Materials, EPA 600/M4-82-020. Analysis by PLM was performed by visual observation of the bulk sample and slides prepared of the bulk sample for microscopic examination and identification. The samples were analyzed for asbestos (chrysotile, amosite, crocidolite, anthophyllite, and actinolite/tremolite), fibrous non-asbestos constituents (mineral wool, cellulose, etc.) and non-fibrous constituents. Using a stereoscope, the microscopist visually estimated the relative amounts of each constituent by determining the estimated area of the asbestos compared with the area estimate of the total sample.

Paint Chip Sampling

TRC conducted a limited lead coating survey to identify lead-based paint (LBP) and/or lead-containing paint (LCP). The lead paint survey was performed to identify representative testing combinations of suspect LBP/LCP on painted surfaces that made up the majority of the coatings in each area assessed that would present a hazard during renovation or demolition activities.

The general purpose of this investigation was to confirm the presence, and determine the location of LBP and/or LCP coatings and components that will be disturbed in association with the renovation or demolition of the Site. TRC has documented the general condition of such painted building surfaces, characterized the composition of painted surfaces with regard to lead content, and quantified areas/components to define the magnitude to which deteriorated LBP and/or LCP is present, where encountered. Information derived from this survey may be used in communicating potential lead exposure hazards to workers performing abatement and/or demolition. The scope of work associated with this investigation included the following elements:

Visual inspection of painted surfaces and components;

Testing of select painted surfaces and components using paint chip analysis; and

Assess condition and approximate quantities of LBP/LCP for reporting purposes.

Lead-based paint (LBP) is defined by the United States Department of House and Urban Development (HUD) as any paint, varnish, stain, or other applied coating that has one mg/cm2 or more of lead or 0.5% by weight (5,000 micrograms per gram [ug\g] or 5,000 parts of lead per million [ppm]). According the OSHA Program Directive, Lead: Exposure in Construction, "For all occupational exposure to lead occurring in the course of construction work, the standard (1926.62) does not specify a minimum amount or concentration of lead that triggers a determination that lead is present and the potential for occupational exposure exists." Therefore any paint containing less than 0.5% by weight, but greater than the laboratory detection limit is considered to be LCP.

- 4 -

Paint chip samples were collected from painted surfaces to determine total lead content and assist in determining Occupational Safety and Health Administration (OSHA) requirements with respect to construction activities which may disturb LCP.

All paint chip samples were submitted under proper COC documentation to the laboratory.

Samples were analyzed by flame AAS utilizing the Environmental Protection Agency (EPA) Test Method for Evaluating Solid Waste, Physical/Chemical Methods, EPA SW-846 Method 7000B.

Laboratory Analysis

Laboratory services were provided by two EMSL Analytical, Inc. locations: a New York State Department of Health (NYSDOH) Environmental Laboratory Accreditation Program (ELAP) accredited laboratory (ELAP #11469) located in Carle Place, NY, and a National Voluntary Laboratory Accreditation Program (NVLAP) certified laboratory (NVLAP #101048-9) located in Long Island City, NY.

FINDINGS

Asbestos-Containing Materials (ACM) – Positive (>1%)

Laboratory results of the bulk sampling indicated the following materials sampled contained asbestos in concentrations greater than 1% (>1%), based on the PLM and/or TEM methods:

Sample(s) Material Location(s) Percentage /

Type Approx.

Quantity

Condition / Material Type /

NESHAP Category

Black Tar Sealant between

Flashing and Roof Deck

VOR Roof- Mounted Teepee

Structure and Adjoining Materials

1.6% Chrysotile

60 SF

Good Misc.

Cat I

Black Tar Sealant between Joints of Outermost

Layer of Flashing

VOR Roof- Mounted Teepee

Structure and Adjoining Materials

1.2% Chrysotile

60 SF

Good Misc.

Cat I

Non-ACM - Trace Asbestos (<1%)

Laboratory results of the bulk sampling indicated the following materials sampled contained asbestos in concentrations less than one percent (<1%) but greater than 0.1 percent (>0.1%), based on the PLM and/or TEM methods:

Sample(s) Material Location(s) Percentage /

Type Approx.

Quantity

Condition / Material Type /

NESHAP Category

White Caulking around Teepee

Structure

VOR Roof- Mounted Teepee

Structure and Adjoining Materials

<1% Chrysotile 22 SF Good Misc.

Cat II

- 5 -

Negative Materials (No Asbestos Detected)

Laboratory results of the bulk sampling indicated the following sampled materials did not contain detectable levels of asbestos, based on the PLM and/or TEM methods:

Sample(s) Material Description Location(s) Estimated Quantity

Condition

Outermost Layer of Flashing

VOR Roof-Mounted Teepee Structure and Adjoining Materials

60 SF Good

Brown Insulative Gasket around Access Door to

Teepee Structure

VOR Roof-Mounted Teepee Structure

1 SF Damaged

White/Yellow Fiberglass/Vinyl Walls of

Teepee Structure

VOR Roof-Mounted Teepee Structure

260 SF Good

Paint Chip Sampling Results

Sample Number Location Description % Lead

(by weight)

Lead-Based Paint / Lead- Containing

Paint

LCP - 01

Engine Generator

Room Ceiling White Paint on Wood 0.49 LCP

LCP - 02

Roof-Mounted

Teepee Structure Base Access Hatch

White Paint on Wood 0.36 LCP

LCP - 03

Engine Generator

Room Ceiling White Paint on

Fiberboard

0.73 LBP

LCP - 04

Roof-Mounted

Teepee Structure Floor

Dark Gray Paint on Wood

4.1 LBP

LCP - 05

Roof-Mounted

Teepee Structure Floor

Light Gray Paint on Wood

2.8 LBP

LCP - 06

Roof-Mounted

Teepee Structure Exterior

White Paint on Fiberglass/Vinyl

0.024 LCP

Laboratory results of the paint chip sampling indicated that lead was detected in six (6) of the six

(6) samples that were collected and analyzed as part of this survey.

RECOMMENDATIONS

Asbestos-Containing Materials

Laboratory results of the bulk sampling indicated that asbestos was present in the black tar sealant between the flashing and roof deck, the black tar sealant between the joints of the outermost layer of flashing, and the white caulking around the roof-mounted teepee structure. The remaining samples analyzed by the laboratory based on the PLM and TEM methods were

- 6 -negative for asbestos. Any materials uncovered during renovation or demolition activities that are not addressed in this survey report, or presumed asbestos-containing materials (PACM), must be sampled by an accredited asbestos inspector and/or investigator prior to any disturbance, or they must be treated as asbestos-containing materials (ACM).

Lead-Containing Paint Sampling Results

Laboratory results of the paint chip sampling indicated that lead was present above the reporting limits in six (6) of the six (6) samples that were collected and analyzed. Lead-based paint (LBP) is defined as paint containing greater than or equal to 0.5 percent lead by weight (≥0.5%) or greater than or equal to 5,000 parts per million (≥5,000 ppm). Any paint containing less than 0.5% by weight (<0.5%), but greater than the laboratory detection limit is considered to be lead-containing paint (LCP). For any paint in which lead was detected, TRC recommends that any renovation activities that may disturb painted surfaces be conducted according to the Occupational Safety and Heath Administration (OSHA) requirements regarding lead in construction (29 CFR 1926.62).

DISCLAIMER

The content presented in this report is based on data collected during the survey, review of pertinent regulations, requirements, guidelines and commonly followed industry standards, and information provided by Client and their clients, agents, and representatives.

The work has been conducted in an objective and unbiased manner and in accordance with generally accepted professional practice for this type of work. TRC believes the data and analysis to be accurate and relevant, but cannot accept responsibility for the accuracy or completeness of available documentation or possible withholding of information of other parties.

This limited hazardous materials survey report is designed to aid the property owner, architect, construction manager, general contractor, and asbestos abatement contractor in locating ACM and LBP or LCP.

Sincerely, TRC Environmental Corporation

Aaron Monto Adam Carity, CIEC, CFSAT Staff Industrial Hygienist Office Practice Leader

Appendix A – Sample Location Diagram(s)

LIMITED HAZARDOUS MATERIALS SURVEY

TRC Project No.: 545895 Figure: 1

Drawn by: AM Date: May 2023Reviewed by: AC

4747 North 7th Street, Suite 422 Phoenix, AZ 85014

Phone: (602) 266-8288 Fax: (602) 266-9355

SYR VOR FACILITY – TEEPEE REPLACEMENT PROJECT

SYRACUSE HANCOCK INTERNATIONAL AIRPORT

1000 COLONEL EILEEN COLLINS BOULEVARD, SYRACUSE, NY 13212

LEGEND

- Asbestos-Containing Sample Location

- Non-Asbestos Sample Location

LIMITED HAZARDOUS MATERIALS SURVEY

TRC Project No.: 545895 Figure: 2

Drawn by: AM Date: May 2023Reviewed by: AC

4747 North 7th Street, Suite 422 Phoenix, AZ 85014

Phone: (602) 266-8288 Fax: (602) 266-9355

SYR VOR FACILITY – TEEPEE REPLACEMENT PROJECT

SYRACUSE HANCOCK INTERNATIONAL AIRPORT

1000 COLONEL EILEEN COLLINS BOULEVARD, SYRACUSE, NY 13212

LEGEND

- Lead-Containing Paint Sample Location

LCP - 02

LCP - 06

LCP - 05

LCP - 04

LCP - 03

LCP - 01

Appendix B – Representative Photographs

SYR VOR FACILITY

FAA – ROOF-MOUNTED TEEPEE REPLACEMENT PROJECT

SYRACUSE HANCOCK INTERNATIONAL AIRPORT

OVERVIEW PHOTOGRAPHIC LOG

SYRACUSE HANCOCK INTERNATIONAL AIRPORT

SUSPECT ASBESTOS-CONTAINING MATERIALS PHOTOGRAPHIC LOG

Sample Numbers: 01, 02, 03

Material Description: Black Tar Sealant between Flashing and Roof Deck

Material Color: Black

Accessible Material: Accessible

Reason Inaccessible: N/A

Asbestos Detected: Positive

Asbestos Type: 1.6% Chrysotile

Homogeneous Area: VOR Roof-Mounted Teepee Structure and Adjoining Materials

Total Approximate Quantity: 60 SF

Condition: Good

Material Type: Misc.

NESHAP Category: Cat I

Notes: Not Applicable

Sample Numbers: 04, 05, 06

Material Description: Outermost Layer of Flashing

Material Color: Black

Accessible Material: Accessible

Reason Inaccessible: N/A

Asbestos Detected: Negative

Asbestos Type: No Asbestos Detected

Homogeneous Area: VOR Roof-Mounted Teepee Structure and Adjoining Materials

Total Approximate Quantity: 60 SF

Condition: Good

Material Type: Misc.

NESHAP Category: N/A

Notes: Not Applicable Sample Numbers: 07, 08, 09

Material Description: Black Tar Sealant between Joints of Outermost Layer of Flashing

Material Color: Black

Accessible Material: Accessible

Reason Inaccessible: N/A

Asbestos Detected: Positive

Asbestos Type: 1.2% Chrysotile

Homogeneous Area: VOR Roof-Mounted Teepee Structure and Adjoining Materials

Total Approximate Quantity: 60 SF

Condition: Good

Material Type: Misc.

NESHAP Category: Cat I

Notes: Not Applicable

SYRACUSE HANCOCK INTERNATIONAL AIRPORT

SUSPECT ASBESTOS-CONTAINING MATERIALS PHOTOGRAPHIC LOG

Sample Numbers: 10, 11, 12

Material Description: White Caulking around Teepee Structure

Material Color: White

Accessible Material: Accessible

Reason Inaccessible: N/A

Asbestos Detected: Positive

Asbestos Type: <1% Chrysotile

Homogeneous Area: VOR Roof-Mounted Teepee Structure and Adjoining Materials

Total Approximate Quantity: 22 SF

Condition: Good

Material Type: Misc.

NESHAP Category: Cat II

Notes: Not Applicable

Sample Numbers: 13, 14, 15

Material Description: Brown Insulative Gasket around Access Door to Teepee Structure

Material Color: Brown

Accessible Material: Accessible

Reason Inaccessible: N/A

Asbestos Detected: Negative

Asbestos Type: No Asbestos Detected

Homogeneous Area: VOR Roof-Mounted Teepee Structure

Total Approximate Quantity: 1 SF

Condition: Damaged

Material Type: Misc.

NESHAP Category: N/A

Notes: Not Applicable Sample Numbers: 16, 17, 18

Material Description: White/Yellow Fiberglass/Vinyl Walls of Teepee Structure

Material Color: White Yellow

Accessible Material: Accessible

Reason Inaccessible: N/A

Asbestos Detected: Negative

Asbestos Type: No Asbestos Detected

Homogeneous Area: VOR Roof-Mounted Teepee Structure

Total Approximate Quantity: 260 SF

Condition: Good

Material Type: Misc.

NESHAP Category: N/A

Notes: Not Applicable

SYRACUSE HANCOCK INTERNATIONAL AIRPORT

LEAD-CONTAINING PAINT PHOTOGRAPHIC LOG

Sample Numbers: LCP - 01

Sample Location: Engine Generator Room Ceiling

Description: White Paint

Laboratory Result (%): 0.49

Substrate: Wood

Paint Locations: Throughout

Quantity of Deteriorated Paint (SF): TBD

Sample Numbers: LCP - 02

Sample Location: Roof-Mounted Teepee Structure Base Access Hatch

Description: White Paint

Laboratory Result (%): 0.36

Substrate: Wood

Sample Numbers: LCP - 03

Sample Location: Engine Generator Room Ceiling

Description: White Paint

Laboratory Result (%): 0.73

Substrate: Fiberboard

SYRACUSE HANCOCK INTERNATIONAL AIRPORT

LEAD-CONTAINING PAINT PHOTOGRAPHIC LOG

Sample Numbers: LCP - 04

Sample Location: Roof-Mounted Teepee Structure Floor

Description: Dark Grey Paint

Laboratory Result (% wt.): 4.1

Substrate: Wood

Sample Numbers: LCP - 05

Floor

Description: Light Grey Paint

Laboratory Result (%): 2.8

Substrate: Wood

Sample Numbers: LCP - 06

Exterior

Description: White Paint

Laboratory Result (%): 0.024

Substrate: Fiberglass/Vinyl

Appendix C – Laboratory Results and Chain of Custody

EMSL Analytical, Inc.

10-39 45th Road Long Island City, NY 11101

Tel/Fax: (212) 290-0051 / (212) 290-0058 http://www.EMSL.com / manhattanlab@emsl.com

032304554EMSL Order:

Customer ID: TRCE51

Customer PO: 545895

Project ID:

Attention: Phone:Dmitriy Khimich (212) 221-7822

Fax:TRC Environmental Corporation (212) 221-7840

Received Date:1430 Broadway 04/28/2023 8:32 PM

Analysis Date:10th Floor 05/14/2023 - 05/16/2023

Collected Date:New York, NY 10018 04/28/2023

Project: 545895 / FAA - SYR VOR Facility Room-Mounted Tee-pee Replacement, FAA - Syracuse Hancock

International Airport - VOR Facility, Syracuse, New York

Test Report:Asbestos Analysis of Bulk Material

Test Color

Analyzed

Date Fibrous Non-Fibrous Asbestos

Non-Asbestos

Sample ID 01 Description SYR VOP Tee-Pee on the Top - Roof Flashing Bottom Tar, Black

032304554-0001 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Black05/14/2023 <1.00% Glass 100.00% Other Inconclusive : <1% Chrysotile

TEM NYS 198.4 NOB Positive Stop (Not Analyzed)05/14/2023

Sample ID 02 Description SYR VOP Tee-Pee on the Top - Roof Flashing Bottom Tar, Black

032304554-0002 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Black05/14/2023 None 98.40% Other 1.60% Chrysotile

TEM NYS 198.4 NOB Positive Stop (Not Analyzed)05/14/2023

Sample ID 03 Description SYR VOP Tee-Pee on the Top - Roof Flashing Bottom Tar, Black

032304554-0003 Homogeneity

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Positive Stop (Not Analyzed)05/14/2023

TEM NYS 198.4 NOB Positive Stop (Not Analyzed)05/14/2023

Sample ID 04 Description SYR VOP Tee-Pee on the Top - Roof Flashing Top Layer , Black

032304554-0004 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Black Inconclusive: None Detected05/14/2023 <1.00% Glass 100.00% Other

TEM NYS 198.4 NOB Black None Detected05/16/2023 100.00% Other

Sample ID 05 Description SYR VOP Tee-Pee on the Top - Roof Flashing Top Layer , Black

032304554-0005 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Black Inconclusive: None Detected05/14/2023 1.70% Glass 98.30% Other

TEM NYS 198.4 NOB Black None Detected05/16/2023 100.00% Other

Initial report from: 05/14/2023 17:36:19

Page 1 of 5ASB_198x_0009_0001 Printed 5/16/2023 11:32:59PM

Tel/Fax: (212) 290-0051 / (212) 290-0058 http://www.EMSL.com / manhattanlab@emsl.com

032304554EMSL Order:

Customer ID: TRCE51

Customer PO: 545895

Project ID:

Test Report:Asbestos Analysis of Bulk Material

Test Color

Analyzed

Date Fibrous Non-Fibrous Asbestos

Non-Asbestos

Sample ID 06 Description SYR VOP Tee-Pee on the Top - Roof Flashing Top Layer , Black

032304554-0006 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Black Inconclusive: None Detected05/14/2023 <1.00% Glass 100.00% Other

TEM NYS 198.4 NOB Black None Detected05/16/2023 100.00% Other

Sample ID 07 Description SYR VOP Tee-Pee on the Top - Roof Flashing Top Layer Joints Tar, Black

032304554-0007 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Black05/14/2023 None 98.80% Other 1.20% Chrysotile

TEM NYS 198.4 NOB Positive Stop (Not Analyzed)05/14/2023

Sample ID 08 Description SYR VOP Tee-Pee on the Top - Roof Flashing Top Layer Joints Tar, Black

032304554-0008 Homogeneity

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Positive Stop (Not Analyzed)05/14/2023

TEM NYS 198.4 NOB Positive Stop (Not Analyzed)05/14/2023

Sample ID 09 Description SYR VOP Tee-Pee on the Top - Roof Flashing Top Layer Joints Tar, Black

032304554-0009 Homogeneity

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Positive Stop (Not Analyzed)05/14/2023

TEM NYS 198.4 NOB Positive Stop (Not Analyzed)05/14/2023

Sample ID 10 Description SYR VOP Tee-Pee on the Top - Joints Caulking , White

032304554-0010 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB White/ Black Inconclusive: None Detected05/14/2023 100.00% Other

TEM NYS 198.4 NOB White/ Black05/16/2023 None 100.00% Other <1% Chrysotile

Sample ID 11 Description SYR VOP Tee-Pee on the Top - Joints Caulking , White

032304554-0011 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB White/ Black Inconclusive: None Detected05/14/2023 100.00% Other

TEM NYS 198.4 NOB White/ Black05/16/2023 None 100.00% Other <1% Chrysotile

Page 2 of 5ASB_198x_0009_0001 Printed 5/16/2023 11:32:59PM

Tel/Fax: (212) 290-0051 / (212) 290-0058 http://www.EMSL.com / manhattanlab@emsl.com

032304554EMSL Order:

Customer ID: TRCE51

Customer PO: 545895

Project ID:

Test Report:Asbestos Analysis of Bulk Material

Test Color

Analyzed

Date Fibrous Non-Fibrous Asbestos

Non-Asbestos

Sample ID 12 Description SYR VOP Tee-Pee on the Top - Joints Caulking , White

032304554-0012 Homogeneity Heterogeneous

PLM NYS 198.1 Friable Not Analyzed

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB White/ Black Inconclusive: None Detected05/14/2023 100.00% Other

TEM NYS 198.4 NOB White/ Black None Detected05/16/2023 100.00% Other

Sample ID 13 Description SYR VOP Tee-Pee on the Top - Access Door Insulation Gasket , Brown

032304554-0013 Homogeneity Homogeneous

PLM NYS 198.1 Friable Brown None Detected05/14/2023 100.00% Non-fibrous (other)

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Not Analyzed

TEM NYS 198.4 NOB Not Analyzed

Sample ID 14 Description SYR VOP Tee-Pee on the Top - Access Door Insulation Gasket , Brown

032304554-0014 Homogeneity Homogeneous

PLM NYS 198.1 Friable Brown None Detected05/14/2023 100.00% Non-fibrous (other)

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Not Analyzed

TEM NYS 198.4 NOB Not Analyzed

Sample ID 15 Description SYR VOP Tee-Pee on the Top - Access Door Insulation Gasket , Brown

032304554-0015 Homogeneity Homogeneous

PLM NYS 198.1 Friable Brown None Detected05/14/2023 25.00%

3.00%

10.00%

55.00%

7.00%

Ca Carbonate

Mica

Non-fibrous (other)

Perlite

Quartz

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Not Analyzed

TEM NYS 198.4 NOB Not Analyzed

Sample ID 16 Description SYR VOP Tee-Pee on the Top - Fiberglass Tee-Pee, White, Yellow

032304554-0016 Homogeneity Homogeneous

PLM NYS 198.1 Friable Gray/ White None Detected05/14/2023 85.00% Glass 10.00%

5.00%

Non-fibrous (other)

Quartz

Result includes a small amount of inseparable attached material

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Not Analyzed

TEM NYS 198.4 NOB Not Analyzed

Sample ID 17 Description SYR VOP Tee-Pee on the Top - Fiberglass Tee-Pee, White, Yellow

032304554-0017 Homogeneity Homogeneous

PLM NYS 198.1 Friable Gray/ White None Detected05/14/2023 80.00% Glass 15.00%

5.00%

Non-fibrous (other)

Quartz

Result includes a small amount of inseparable attached material

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Not Analyzed

TEM NYS 198.4 NOB Not Analyzed

Page 3 of 5ASB_198x_0009_0001 Printed 5/16/2023 11:32:59PM

Tel/Fax: (212) 290-0051 / (212) 290-0058 http://www.EMSL.com / manhattanlab@emsl.com

032304554EMSL Order:

Customer ID: TRCE51

Customer PO: 545895

Project ID:

Test Report:Asbestos Analysis of Bulk Material

Test Color

Analyzed

Date Fibrous Non-Fibrous Asbestos

Non-Asbestos

Sample ID 18 Description SYR VOP Tee-Pee on the Top - Fiberglass Tee-Pee, White, Yellow

032304554-0018 Homogeneity Homogeneous

PLM NYS 198.1 Friable Gray/ White None Detected05/14/2023 80.00% Glass 7.00%

10.00%

3.00%

Ca Carbonate

Non-fibrous (other)

Quartz

PLM NYS 198.6 VCM Not Analyzed

PLM NYS 198.6 NOB Not Analyzed

TEM NYS 198.4 NOB Not Analyzed

Page 4 of 5ASB_198x_0009_0001 Printed 5/16/2023 11:32:59PM

Tel/Fax: (212) 290-0051 / (212) 290-0058 http://www.EMSL.com / manhattanlab@emsl.com

032304554EMSL Order:

Customer ID: TRCE51

Customer PO: 545895

Project ID:

Test Report:Asbestos Analysis of Bulk Material

The samples in this report were submitted to EMSL for analysis by Asbestos Analysis of Bulk Materials via NYS ELAP Approved Methods. The reference number for these samples is the EMSL Order ID above. Please use this reference number when calling about these samples.

Report Comments:

Sample Receipt Date:

Analysis Completed Date: Analysis Completed Time:

Sample Receipt Time:4/28/2023 8:32 PM

5/16/2023 4:10 PM

Analyst(s):

Angelica Serrano PLM NYS 198.1 Friable (4) Kerrie Gibson PLM NYS 198.1 Friable (2)

Kerrie Gibson PLM NYS 198.6 NOB (9) Steven Dutter TEM NYS 198.4 NOB (6)

Samples reviewed and approved by:

Charles Johnson, Asbestos Laboratory Manager or Other Approved Signatory

EMSL maintains liability limited to cost of analysis. Interpretation and use of test results are the responsibility of the client. This report relates only to the samples reported above, and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. The report reflects the samples as received. Results are generated from the field sampling data (sampling volumes and areas, locations, etc.) provided by the client on the Chain of Custody. Samples are within quality control criteria and met method specifications unless otherwise noted. Estimation of uncertainty available upon request.

This report is a summary of multiple methods of analysis, fully compliant reports are available upon request. All samples examined for the presence of vermiculite when analyzed via NYS 198.1. A combination of PLM and TEM analysis may be necessary to ensure consistently reliable detection of asbestos. Polarized-light microscopy is not consistently reliable in detecting asbestos in floor coverings and similar non-friable organically bound materials. This report must not be used to claim product endorsement by

NVLAP of any agency or the U.S. Government . Quantitative transmission electron microscopy is currently the only method that can be used to determine if this material can be considered or treated as non-asbestos containing. NOB= Non friable organically bound; N/A= Not applicable VCM= Vermiculite containing material.

Samples analyzed by EMSL Analytical, Inc. Long Island City, NY NYS ELAP 11506, NVLAP Lab Code 101048-9

Page 5 of 5ASB_198x_0009_0001 Printed 5/16/2023 11:32:59PM

O r d e r I D

P a g e f d e r I D

P a g e

Client Sample Description ConcentrationLab ID Analyzed Lead

Collected

EMSL Analytical, Inc.

528 Mineola Avenue, Carle Place, NY 11514 Phone/Fax: (516) 997-7251 / (516) 997-7528 http://www.EMSL.com carleplacelab@emsl.com

Attn: Dimitriy Khimich TRC Environmental Corporation 1430 Broadway 10th Floor New York, NY 10018

Received: 5/1/2023 07:14 PM

Federal Avaiation Administration (FAA); FAA - SYR VOR Facility Room-Mounted Tee-pee Replacemet FAA - Syracuse Hancock

Fax: (212) 221-7840 Phone: (212) 221-7822

Project:

4/28/2023Collected:

Test Report: Lead in Paint Chips by Flame AAS (SW 846 3051A/7000B)*

062307610 CustomerID: TRCE51 CustomerPO: 545895000000000 ProjectID:

EMSL Order:

Site: SYR VOP Engine Generator Room Ceiling Desc: White Paint Wood

062307610-0001LCP - 01 0.49 % wt5/7/20234/28/2023

Site: SYR VOR Tee-Pee Base Access Hatch Desc: White Paint Wood

062307610-0002LCP - 02 0.36 % wt5/7/20234/28/2023

Site: SYR VOP Ceiling Area of the EG Room Desc: White Paint Wood

062307610-0003LCP - 03 0.73 % wt5/7/20234/28/2023

Site: SYR VOP Tee-Pee Inside Base Desc: Dark Grey Paint Wood

062307610-0004LCP - 04 4.1 % wt5/7/20234/28/2023

Site: SYR VOP Tee-Pee Inside Base Desc: Light Grey Paint Wood

062307610-0005LCP - 05 2.8 % wt5/7/20234/28/2023

Site: SYR VOP Tee-Pee on the Top Desc: White Paint Fiberglass Plastic

062307610-0006LCP - 06 0.024 % wt5/7/20234/28/2023

James Han, Chemistry Laboratory Manager or other approved signatory

Test Report ChmSnglePrm/nQC-7.32.3 Printed: 5/8/2023 8:12:18 AM

EMSL maintains liability limited to cost of analysis. Interpretation and use of test results are the responsibility of the client. This report relates only to the samples reported above, and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. The report reflects the samples as received.

Results are generated from the field sampling data (sampling volumes and areas, locations, etc.) provided by the client on the Chain of Custody. Samples are within quality control criteria and met method specifications unless otherwise noted.

Analysis following Lead in Paint by EMSL SOP/Determination of Environmental Lead by FLAA. Reporting limit is 0.008% wt. based on the minimum sample weight per our SOP. "<" (less than) result signifies the analyte was not detected at or above the reporting limit. Measurement of uncertainty is available upon request. Definitions of modifications are available upon request.

Samples analyzed by EMSL Analytical, Inc. Carle Place, NY AIHA LAP, LLC-ELLAP Accredited #102344, CT PH-0249, NYS ELAP 11469, CA 2339

Initial report from 05/08/2023 08:12:18 http://www.EMSL.com mailto:carleplacelab@emsl.com d e r I D

P a g e d e r I D

P a g e

Appendix D – Certification(s)

Dmitriy Khimich has fulfilled the requirements of the Toxic Substances Control Act (TSCA) Section 402, and has received certification to conduct lead-based paint activities pursuant to 40 CFR Part 745.226 as:

All EPA Administered Lead-based Paint Activities Program States, Tribes and Territories

This certification is valid from the date of issuance and expires July 20, 2025

Certification #

LBP-R-15508-3

Issued On

February 18, 2022

Ben Conetta, Chief

Chemicals and Multimedia Programs Branch

Risk Assessor