A-007_EngineeringDesignCodesStandards.pdf

ORD APPROVED ENGINEERING AND DESIGN CODES

This attachment it intended to provide supporting documentation for NETL P414.1-3, “ORD Approved Engineering Design Codes and Standards”. The approved codes and standards have been categorized into the following areas; 1) Structural, 2) Pressure Vessels, Pipes, Valves and Fittings, 3) Welding, 4) Compressed Gases in Vendor Supplied Cylinders, 5) Instrumentation and Calibration, 6) Electrical, and

7) Fire Protection. This attachment does not contain listings for standard material specifications relating to structural steel, pipes, valves, fittings and fasteners.

1. Structural – The following codes, standards, and best engineering practices shall be applied to the design, specification and installation of components or systems intended to support or distribute loads:

• ACI 207.1, Mass Concrete

• ACI 211.3, Standard Practice for Selecting Proportions for No-Slump Concrete

• ACI 304 (304R), Guide for Measuring, Mixing, Transporting, and Placing Concrete

• ACI 309, Guide for Consolidation of Concrete

• ACI 318M-02/318RM, Metric Building Code Requirements for Structural Concrete

Commentary

• ACI 336.2, Suggested Analysis and Design Procedures for Combined Footings and Mats

• ACI 336.3, Design and Construction of Drilled Piers

• ACI 347, Guide to Formwork for Concrete

• AISC Code of Standard Practice for Steel Buildings and Bridges

• AISC Manual of Steel Construction

• AISC, Manual of Steel Construction Allowable Stress Design and Plastic Design

• AISC, Manual of Steel Construction Load and Resistance Factor Design

• ASCE 7, Minimum Design Loads for Buildings and Other Structures

• International Code Council International Building Code

• UL Fire Resistance Directory

• OSHA 29 Code of Federal Regulations Part 1910

Revision Date: May 17, 2007 Contact: Mara Dean

2. Pressure Vessels, Pipes, Valves and Fittings – The following codes, standards, and best engineering practices shall be applicable to the design, fabrication, inspection, testing, specification and certification of pressure vessels and piping components operating at either internal or external pressures exceeding 15 PSIG.

• ASME B31.1, Power Piping

• ASME B31.3, Process Piping

• NFPA 54, National Fuel Gas Code

• ASME Boiler and Pressure Vessel Code Section II - Materials Part A, Ferrous Material

Specifications

• ASME Boiler and Pressure Vessel Code Section II, Materials Part B, Nonferrous Material Specifications

• ASME Boiler and Pressure Vessel Code Section II, Materials Part C, Specifications for

Welding Rods Electrodes and Filler Metals

• ASME Boiler and Pressure Vessel Code Section II , Materials Part D, Properties

• ASME Boiler and Pressure Vessel Code Section V, Nondestructive Examination

• ASME Boiler and Pressure Vessel Code Section VIII, Division 1, Rules for Construction of Pressure Vessels

• ASME Boiler and Pressure Vessel Code Section VIII, Division 2, Rules for Construction of

Pressure Vessels – Alternative Rules

• ASME Boiler and Pressure Vessel Code Section VIII, Division 3, Rules for Construction of High Pressure Vessels – Alternative Rules

• ASME Boiler and Pressure Vessel Code Section IX, Welding and Brazing Qualifications

• ASME PTC 25, Pressure Relief Devices

• ASME B16.10, Face to Face and End to End Dimensions of Valves

• ASME PCC-1, Guidelines for Pressure Boundary Bolted Flange Joint Assembly

• ASME Boiler and Pressure Vessel Code Section X, Fiber Reinforced Plastic Pressure

Vessels

• WRC 107, Local Stresses in Spherical and Cylindrical Shells Due to External Loadings

• WRC 198, Secondary Stress Indices for Integral Structural Attachments for Straight Pipe;

Stress Indices at Lug Supports on Piping Systems

• ISA Standards and Practices for Instrumentation and Control

• ASME B1.20.1, Pipe Threads, General Purpose, Inch

• NB-23, “National Board Inspection Code”

3. Welding – The following codes, standards, and best engineering practices shall be applicable to weld certification, specification, performance and inspection.

• ASNT Recommended Practice No. SNT-TC-1A, Recommended Practices for Qualification and Certification of Inspectors.

• AWS D1.1, Structural Welding Code - Steel

• AWS D1.2, Structural Welding Code - Aluminum

• AWS D9.1, Structural Welding Code - Sheet Metal

• AWS B1.1, Guide for the Visual Inspection of Welds

• ASME Boiler and Pressure Vessel Code Section V, Non-Destructive Examination

• ASME Boiler and Pressure Vessel Code Section IX, Welding and Brazing Qualifications

• ASME Boiler and Pressure Vessel Code Section II Part C, Welding Rods, Electrodes, and

Filler Metals

4. Compressed Gases in Vendor Supplied Cylinders – The following codes, standards, and best engineering practices shall be applicable to cylinder gas pipe and valve design, specification, installation and inspection.

• CGA C-6, Standards for Visual Inspection of Steel Compressed Gas Cylinders

• CGA C-6.1, Standards for Visual Inspection of High Pressure Aluminum Compressed Gas

Cylinders

• CGA C-6.4, Methods for External Visual Inspection of Natural Gas Vehicle (NGV) Fuel Containers and Their Installations

• CGA E-1, Standard Connections for Regulator Outlets, Torches, and Fitted Hose for

Welding and Cutting Equipment

• CGA E-2, Hose Line Check Valve Standards for Welding and Cutting

• CGA E-3, Pipeline Regulator Inlet Connection Standards

• CGA E-4, Standard for Gas Pressure Regulators

• CGA E-5, Torch Standard

• CGA E-8, Standard for Gas Flowmeters

• CGA E-9, Standard for Flexible, PTFE-Lined Pigtails for Compressed Gas Service

• CGA E-11, Standard for Stationary Compressed Gas Cylinder Discharging Manifolds for Working Pressures up to 3000 psig

• CGA E-14, Maximum Leakage Rates (Gas Tightness) Of Equipment Used For Welding, Cutting, and Allied Processes

• CGA G-1, Acetylene

• CGA G-1.6, Recommended Practices for Mobile Acetylene Trailer Systems

• CGA G-3, Sulfur Dioxide

• CGA G-4, Oxygen

• CGA G-4.1, Cleaning Equipment for Oxygen Service

• CGA G-4.4, Industrial Practices for Gaseous Oxygen Transmission and Distribution Piping Systems

• CGA G-5, Hydrogen

• CGA G-5.4, Standard for Hydrogen Piping Systems at Consumer Locations

• CGA G-5.5, Hydrogen Vent Systems

• CGA G-6, Carbon Dioxide

• CGA G-6.1, Standard for Insulated Carbon Dioxide Systems at Consumer Sites

• CGA G-6.5, Standard for Small, Stationary, Insulated Carbon Dioxide Supply Systems

• CGA G-12, Hydrogen Sulfide

• CGA P-1, Safe Handling of Compressed Gases in Containers

• CGA P-6, Standard Density Data, Atmospheric Gases and Hydrogen

• CGA P-9, The Inert Gases: Argon, Nitrogen, and Helium

• CGA P-12, Safe Handling of Cryogenic Liquids

• CGA P-18, Standard for Bulk Inert Gas Systems at Consumer Sites

• CGA P-20, Standard for the Classification of Toxic Gas Mixtures

• CGA S-1.1, Pressure Relief Device Standards-Part 1-Cylinders for Compressed Gases

• CGA S-1.3, Pressure Relief Device Standards-Part 3-Stationary Storage Containers for

Compressed Gases

• CGA S-7, Method for Selecting Pressure Relief Devices for Compressed Gas Mixtures in Cylinders

• CGA V-1, Compressed Gas Association Standard for Compressed Gas Cylinder Valve

Outlet and Inlet Connections

• CGA V-6, Standard Cryogenic Liquid Transfer Connections

• CGA V-6.1, Standard Carbon Dioxide Transfer Connections

• CGA V-9, Compressed Gas Association Standard for Compressed Gas Cylinder Valves

• CGA V-10, High Pressure Gas Trailer Connections

5. Instrumentation and Calibration – The following codes, standards, and best engineering practices shall be applicable to the design, specification, fabrication, inspection, testing, calibration and certification of Instrumentation Measurement and Control Systems.

• ANSI/NCSL Z540-1, Calibration Laboratories and Measuring Test Equipment --- General Requirements

• ISA-RP2.1-1978 - Manometer Tables

• ISA-5.1-1984 (R1992) - Instrumentation Symbols and Identification (Formerly ANSI/ISA-5.1-

1984 [R1992])

• ISA-5.2-1976 (R1992) - Binary Logic Diagrams for Process Operations (Formerly ANSI/ISA-

5.2-1976 [R1992])

• ISA-5.3-1983 - Graphic Symbols for Distributed Control/Shared Display Instrumentation, Logic and Computer Systems

• ISA-5.4-1991 - Instrument Loop Diagrams (Formerly ANSI/ISA-5.4-1991)

• ISA-5.5-1985 - Graphic Symbols for Process Displays

• ANSI/ISA-7.0.01-1996 - Quality Standard for Instrument Air

• ANSI/ISA-60079-0 (12.00.01)-2005 - Electrical Apparatus for Use in Class I, Zones 0, 1 & 2

Revision Date: May 17, 2007

Hazardous (Classified) Locations - General Requirements [Supersedes ANSI/ISA-12.00.01-2002 (IEC 60079-0 Ed 3 Mod)]

• ANSI/ISA-12.01.01-1999 - Definitions and Information Pertaining to Electrical Instruments in Hazardous (Classified) Locations

• ANSI/ISA-60079-11 (12.02.01)-2002 [Formerly ANSI/ISA-12.02.01-2002 (IEC 60079-11 Mod)] -Electrical Apparatus for Use in Class I, Zones 0, 1, & 2 Hazardous (Classified) Locations

– Intrinsic Safety “i”

• ISA-TR12.2-1995 - Intrinsically Safe System Assessment Using the Entity Concept

• ISA-RP12.2.02-1996 - Recommendations for the Preparation, Content, and Organization of

Intrinsic Safety Control Drawings

• ANSI/ISA-12.04.01-2003 (IEC 60079-2 Mod) - Electrical Apparatus for Explosive Gas

Atmospheres - Part 2 Pressurized Enclosures “p”

• ISA-RP12.4-1996 - Pressurized Enclosures

• ANSI/ISA-RP12.06.01-2003 - Recommended Practice for Wiring Methods for Hazardous

(Classified) Locations Instrumentation Part 1: Intrinsic Safety (Formerly ANSI/ISA-RP12.06.01- 1995 [R2002])

• ANSI/ISA-TR12.06.01-1999 - Electrical Equipment in a Class I, Division 2/Zone 2 Hazardous Location

• ISA-12.10-1988 - Area Classification in Hazardous (Classified) Dust Locations

• ANSI/ISA-61241-10 (12.10.05-2004) - Electrical Apparatus for Use in Zone 20, Zone 21 and

Zone 22 Hazardous (Classified) Locations - Classification of Zone 20, Zone 21 and Zone 22 Hazardous (Classified) Locations

• ANSI/ISA-12.12.01-2000 - Nonincendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Divisions 1 and 2 Hazardous (Classified) Locations ANSI/ISA-60079- 15 (12.12.02)-2003, Electrical Apparatus for Use in Class I, Zone 2 Hazardous (Classified) Locations - Type of Protection “n”

• ISA-RP12.12.03-2002 - Recommended Practice for Portable Electronic Products Suitable for Use in Class I and II, Division 2, Class I Zone 2 and Class III, Division 1 and 2 Hazardous (Classified) Locations ANSI/ISA-12.13.01-2003 (IEC 61779-1 through 5 Mod), Performance Requirements for Combustible Gas Detectors

• ANSI/ISA-RP12.13.02 (IEC 61779-6 Mod), Recommended Practice for the Installation, Operation, and Maintenance of Combustible Gas Detection Instruments (Formerly ISA-RP12.13, Part II-1987)

• ANSI/ISA-TR12.13.01-1999 (R2005) - Flammability Characteristics of Combustible Gases and Vapors

• ANSI/ISA-TR12.13.02-1999 (R2005) - Investigation of Fire and Explosion Accidents in the Chemical, Mining, and Fuel-Related Industries - A Manual by Kuchta

• ANSI/ISA-60079-7 (12.16.01)-2002 [Formerly ANSI/ISA-12.16.01-2002 (IEC 60079-7 Mod)] – Electrical Apparatus for Use in Class I, Zone 1 Hazardous (Classified) Locations Type of Protection -Increased Safety “e”

• ANSI/ISA-TR12.21.01-2004 - Use of Fiber Optic Systems in Class I Hazardous (Classified) Locations

• ANSI/ISA-60079-1 (12.22.01) -2005 - Electrical Apparatus for Use in Class I, Zone 1 Hazardous (Classified) Locations Type of Protection - Flameproof “d“ [Supersedes ANSI/ISA- 12.22.01-2002 (IEC 60079-1 Ed 3 Mod)]

• ANSI/ISA-60079-18 (12.23.01) -2005 - Electrical Apparatus for Use in Class I, Zone 1

Revision Date: May 17, 2007

Hazardous (Classified) Locations Type of Protection - Encapsulation “m” [Supersedes ANSI/ISA-12.23.01-2002 (IEC 60079-18 Mod)]

• ANSI/ISA-TR12.24.01-1998 (IEC 60079-10 Mod) - Recommended Practice for Classification of Locations for Electrical Installations Classified as Class I, Zone 0, Zone 1, or Zone 2

• ANSI/ISA-60079-5 (12.25.01)-1998 [Formerly ANSI/ISA-12.25.01-1998 (IEC 60079-5 Mod)] - Electrical Apparatus for Use in Class I, Zone 1 Hazardous (Classified) Locations: Type of Protection - Powder Filling “q”

• ANSI/ISA-60079-6 (12.26.01)-1998 [Formerly ANSI/ISA-12.26.01-1998 (IEC 60079-6 Mod)] - Electrical Apparatus for Use in Class I, Zone 1 Hazardous (Classified) Locations Type of Protection - Oil-Immersion “o”

• ANSI/ISA-12.27.01-2003, Requirements for Process Sealing between electrical Systems and Flammable or Combustible Process Fluids

• ISA-18.1-1979 (R2004) - Annunciator Sequences and Specifications (Formerly ANSI/ISA-18.1- 1979 [R1992])

• ISA-20-1981 - Specification Forms for Process Measurement and Control Instruments, Primary Elements and Control Valves

• ISA-TR20.00.01-2001 - Specification Forms for Process Measurement and Control Instruments - Part 1: General Considerations - Updated with 20 New Specification forms in 2004 (also includes ISA-20.00.03-2001, Specification Forms for Process Measurement and Control Instruments - Part 3: Form Requirements and Development Guidelines)

• ISA-RP31.1-1977 - Specification, Installation and Calibration of Turbine Flowmeters

• ISA-37.1-1975 (R1982) - Electrical Transducer Nomenclature and Terminology (Formerly

ANSI MC6.1-1975)

• ISA-37.3-1982 (R1995) - Specifications and Tests for Strain Gage Pressure Transducers

• ISA-37.5-1982 (R1995) - Specifications and Tests for Strain Gage Linear Acceleration

Transducers

• ISA-37.6-1982 (R1995) - Specifications and Tests for Potentiometric Pressure Transducers

• ISA-37.8-1982 (R1995) - Specifications and Tests for Strain Gage Force Transducers

• ISA-37.10-1982 (R1995) - Specifications and Tests for Piezoelectric Pressure and Sound-

Pressure Transducers

• ISA-37.12-1982 (R1995) - Specifications and Tests for Potentiometric Displacement

Transducers

• ISA-37.16.01-2002 - A Guide for the Dynamic Calibration of Pressure Transducers

• ISA-RP42.00.01-2001 - Nomenclature for Instrument Tube Fittings

• ANSI/ISA-50.00.01-1975 (R2002) - Compatibility of Analog Signals for Electronic Industrial

Process Instruments (Formerly ISA-50.1-1982 [R1992])

• ANSI/ISA-51.1-1979 (R1993) - Process Instrumentation Terminology

• ISA-RP52.1-1975 - Recommended Environments for Standards Laboratories

• ISA-RP60.1-1990 - Control Center Facilities

• ISA-RP60.2-1995 - Control Center Design Guide and Terminology

• ISA-RP60.3-1985 - Human Engineering for Control Centers

• ISA-RP60.4-1990 - Documentation for Control Centers

• ISA-RP60.6-1984 - Nameplates, Labels, and Tags for Control Centers

• ISA-RP60.8-1978 - Electrical Guide for Control Centers

• ISA-RP60.9-1981 - Piping Guide for Control Centers

• ISA-RP60.11-1991 - Crating, Shipping and Handling for Control Centers

Revision Date: May 17, 2007

• ISA-71.01-1985 - Environmental Conditions for Process Measurement and Control Systems:

Temperature and Humidity

• ISA-71.02-1991 - Environmental Conditions for Process Measurement and Control Systems:

Power

• ANSI/ISA-71.03-1995 - Environmental Conditions for Process Measurement and Control Systems: Mechanical Influences

• ISA-71.04-1985 - Environmental Conditions for Process Measurement and Control Systems:

Airborne Contaminants

• ISA-RP74.01-1984 - Application and Installation of Continuous-Belt Weighbridge Scales

• ANSI/ISA-75.01.01-2002 (IEC 60534-2-1 Mod) - Flow Equations for Sizing Control Valves

(Formerly ANSI/ISA-75.01-1985 [R1995])

• ANSI/ISA-75.02-1996 - Control Valve Capacity Test Procedures

• ANSI/ISA-TR75.04.01-1998 - Control Valve Position Stability

• ANSI/ISA-75.05.01-2000 (R2005) - Control Valve Terminology

• ISA-75.07-1997 - Laboratory Measurement of Aerodynamic Noise Generated by Control Valves

• ANSI/ISA-75.08-1999 - Installed Face-to-Face Dimensions for Flanged Clamp or Pinch Valves

• ANSI/ISA-75.08.01-2002 (Formerly ISA-75.03-1992), Face-to-Face Dimensions for Integral

Flanged Globe-Style Control Valve Bodies (ANSI Classes 125, 150, 250, 300, and 600)

• ANSI/ISA-75.08.02-2003 - Face-to-Face Dimensions for Flangeless Control Valves (ANSI

Classes 150, 300 and 600) (Formerly ANSI/ISA-75.04-1995)

• ANSI/ISA-75.08.03-2001 - Face-to-Face Dimensions for Socket Weld-End and Screwed-End

Globe-Style Control Valves (Classes 150, 300, 600, 900, 1500, and 2500)

• ANSI/ISA-75.08.04-2001 - Face-to-Face Dimensions for Buttweld-End Globe-Style Control

Valves (Class 4500)

• ANSI/ISA-75.08.05-2002 (Formerly ANSI/ISA-75.15-1994), Face-to-Face Dimensions for

Buttweld-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500, and 2500)

• ANSI/ISA-75.08.06-2002 (Formerly ANSI/ISA-75.16-1994), Face-to-Face Dimensions for

Flanged Globe-Style Control Valve Bodies (ANSI Classes 900, 1500, and 2500)

• ANSI/ISA-75.08.07-2001 - Face-to-Face Dimensions for Separable Flanged Globe-Style Control

Valves (Classes 150, 300, and 600)

• ANSI/ISA-75.08.09-2004 - Face-to-Face Dimensions for Sliding Stem Flangeless Control

Valves (Classes 150, 300, and 600)

• ANSI/ISA-75.11.01-1985 (R2002) [Formerly ANSI/ISA-75.11-1985 (R1997)] - Inherent Flow

Characteristic and Rangeability of Control Valves

• ISA-75.13-1996 - Method of Evaluating the Performance of Positioners with Analog Input

Signals and Pneumatic Output

• ANSI/ISA-75.17-1989 - Control Valve Aerodynamic Noise Prediction

• ISA-75.19.01-2001 - Hydrostatic Testing of Control Valves

• ISA-RP75.21-1989 (R1996) - Process Data Presentation for Control Valves

• ANSI/ISA-75.22-1999 - Face-to-Centerline Dimensions for Flanged Globe-Style Angle Control

Valve Bodies (ANSI Classes 150, 300, and 600)

• ISA-RP75.23-1995 - Considerations for Evaluating Control Valve Cavitation

• ANSI/ISA-75.25.01-2000 - Test Procedure for Control Valve Response Measurement from Step

Inputs

• ANSI/ISA-TR75.25.02-2000 - Control Valve Response Measurement from Step Inputs

• ISA-RP76.0.01-1998 - Analyzer System Inspection and Acceptance

Revision Date: May 17, 2007

• ANSI/ISA-76.00.02-2002 - Modular Component Interfaces for Surface-Mount Fluid Distribution Components - Part 1: Elastomeric Seals - Drum Type

• ANSI/ISA-61010-1 (82.02.01) CSA C22.2 No. 1010.1 and ANSI/UL 61010-1 - Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use - Part 1:

General Requirements (Updated with Annex DV US 22 July 2005)

• ANSI/ISA-82.02.02-1996 (IEC 1010-2-031) - Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use (Identical to IEC 1010-2-031: Particular Requirements for Hand-Held Probe Assemblies for Electrical Measurement and Test)

• ANSI/ISA-82.02.04-1996 (IEC 1010-2-032) - Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use (Identical to IEC 1010-2-032: Particular Requirements for Hand-Held Current Clamps for Electrical Measurement and Test)

• ISA-82.03-1988 - Safety Standard for Electrical and Electronic Test, Measuring, Controlling, and Related Equipment (Electrical and Electronic Process Measurement and Control Equipment) (Partial Revision and Redesignation of ANSI C39.5-1974)

• ANSI/ISA-84.01-1996 - Application of Safety Instrumented Systems for the Process Industries

• ANSI/ISA-84.00.01-2004 Part 1(IEC 61511-1 Mod) - Functional Safety: Safety Instrumented

Systems for the Process Industry Sector - Part 1: Framework, Definitions, System, Hardware and Software Requirements

• ANSI/ISA-84.00.01-2004 Part 2 (IEC 61511-2 Mod) - Functional Safety: Safety Instrumented Systems for the Process Industry Sector - Part 2: Guidelines for the Application of ANSI/ISA- 84.00.01-2004 Part 1 (IEC 61511-1 Mod) - Informative

• ANSI/ISA-84.00.01-2004 Part 3 (IEC 61511-3 Mod) - Functional Safety: Safety Instrumented Systems for the Process Industry Sector - Part 3: Guidance for the Determination of the Required Safety Integrity Levels - Informative

• ISA-TR84.00.02-2002 - Part 1: Safety Instrumented Functions (SIF) - Safety Integrity Level (SIL) Evaluation Techniques Part 1: Introduction

• ISA-TR84.00.02-2002 - Part 2: Safety Instrumented Functions (SIF) - Safety Integrity Level (SIL) Evaluation Techniques Part 2:Determining the SIL of a SIF via Simplified Equations

• ISA-TR84.00.02-2002 - Part 3: Safety Instrumented Functions (SIF) - Safety Integrity Level (SIL) Evaluation Techniques Part 3: Determining the SIL of a SIF via Fault Tree Analysis

• ISA-TR84.00.02-2002 - Part 4: Safety Instrumented Functions (SIF) - Safety Integrity Level (SIL) Evaluation Techniques Part 4:Determining the SIL of a SIF via Markov Analysis

• ISA-TR84.00.02-2002 - Part 5: Safety Instrumented Functions (SIF) - Safety Integrity Level (SIL) Evaluation Techniques Part 5:Determining the PFD of SIS Logic Solvers via Markov Analysis

• ISA-TR84.00.03-2002 - Guidance for Testing of Process Sector Safety Instrumented Functions (SIF) Implemented as or Within Safety Instrumented Systems (SIS)

• ANSI/ISA-88.01-1995 - Batch Control Part 1: Models and Terminology

• ANSI/ISA-88.00.02-2001 - Batch Control Part 2: Data Structures and Guidelines for Languages

• ANSI/ISA-88.00.03-2003, Batch control Part 3: General and Site Recipe Models and

Representation

• ISA-TR88.0.03-1996 - Possible Recipe Procedure Presentation Formats

• ANSI/ISA-91.00.01-2001 - Identification of Emergency Shutdown Systems and Controls That

Are Critical to Maintaining Safety in Process Industries

• ISA-TR91.00.02-2003 - Criticality Classification Guideline for Instrumentation

• ISA-92.0.01, Part I-1998 - Performance Requirements for Toxic Gas-Detection Instruments:

Revision Date: May 17, 2007

Hydrogen Sulfide

• ISA-RP92.0.02, Part II-1998 - Installation, Operation, and Maintenance of Toxic Gas Detection

Instruments: Hydrogen Sulfide

• ANSI/ISA-92.02.01, Part I-1998 - Performance Requirements for Carbon Monoxide Detection

Instruments (50-1000 ppm Full Scale)

• ISA-RP92.02.02, Part II-1998 - Installation, Operation, and Maintenance of Carbon Monoxide

Detection Instruments (50-1000 ppm Full Scale)

• ISA-92.03.01-1998 - Performance Requirements for Ammonia Detection Instruments (25-500 ppm)

• ISA-RP92.03.02-1999 - Installation, Operation, and Maintenance of Ammonia Detection

Instruments (25-500 ppm Full Scale)

• ANSI/ISA-92.04.01, Part I-1996 - Performance Requirements for Instruments Used to Detect

Oxygen-Deficient/Oxygen-Enriched Atmospheres

• ISA-RP92.04.02, Part II-1996 - Installation, Operation, and Maintenance of Instruments Used to

Detect Oxygen-Deficient/Oxygen-Enriched Atmospheres

• ISA-92.06.01-1998 - Performance Requirements for Chlorine Detection Instruments (0.5-30 ppm Full Scale)

• ISA-RP92.06.02-1999 - Installation, Operation, and Maintenance of Chlorine Detection

Instruments (0.5-30 ppm Full Scale)

• ANSI/ISA-TR92.06.03-1999 - Feasibility of Chlorine Detection Instrument Testing

• ANSI/ISA-93.00.01-1999 - Standard Method for the Evaluation of External Leakage of Manual and Automated On-Off Valves

• ANSI/ISA-95.00.01-2000 - Enterprise-Control System Integration - Part 1: Models and

Terminology

• ANSI/ISA-95.00.02-2001 - Enterprise-Control System Integration - Part 2: Object Model

Attributes

• ANSI/ISA-95.00.03-2005 - Enterprise-Control System Integration - Part 3: Models of

Manufacturing Operations Management

• ISA-MC96.1-1982 - Temperature Measurement Thermocouples

• ANSI/ISA-TR99.00.01-2004 - Security Technologies for Manufacturing and Control Systems

• ANSI/ISA-TR99.00.02-2004 - Integrating Electronic Security into the Manufacturing and

Control Systems Environment

• ISO/IEC 17025, General Requirements for the Competence of Testing and Calibration

Laboratories

6. Electrical – The following codes, standards, and best engineering practices shall be applicable to power systems design, specification, installation and inspection.

• NFPA 70, National Electrical Code

• NFPA 70B, Recommended Practice for Electrical Equipment Maintenance

• NFPA 70E, Standard for Electrical Safety Requirements for Employee Workplaces

• NFPA 75, Standard for the Protection of Electronic Computer/Data Processing Equipment

• NFPA 77, Recommended Practice on Static Electricity

• NFPA 79, Electrical Standard for Industrial Machinery

• NFPA 496, Standard for Purged and Pressurized Enclosures for Electrical Equipment

• NFPA 497, Recommended Practice for the Classification of Flammable Liquids, Gases, or Vapors and of Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas

• NFPA 499, Recommended Practice for the Classification of Combustible Dusts and of Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas

• NFPA 780, Standard for the Installation of Lighting Protection Systems

7. Fire Protection – The following codes, standards, and best engineering practices shall be applicable to the design, specification and installation of fire protection systems as they relate to personnel safety.

• NFPA 1, Fire Prevention Code

• NFPA 10, Standard for Portable Fire Extinguishers

• NFPA 13, Standard for the Installation of Sprinkler Systems

• NFPA 14, Standard for the Installation of Standpipe, Private Hydrants, and Hose Systems

• NFPA 25, Standard for the Inspection, Testing, and Maintenance of Water-Based Fire

Protection Systems

• NFPA 30, Flammable and Combustible Liquids Code

• NFPA 31, Standard for the Installation of Oil-Burning Equipment

• NFPA 37, Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines

• NFPA 45, Standard on Fire Protection for Laboratories Using Chemicals

• NFPA 50A, Standard for Gaseous Hydrogen Systems at Consumer Sites

• NFPA 51B, Standard for Fire Prevention During Welding, Cutting, and Other Hot Work

• NFPA 52, Compressed Natural Gas (CNG) Vehicular Fuel Systems Code

• NFPA 54, National Fuel Gas Code

• NFPA 55, Standard for the Storage, Use, and Handling of Compressed and Liquefied Gases in Portable Cylinders

• NFPA 57, Liquefied Natural Gas (LNG) Vehicular Fuel Systems Code

• NFPA 68, Guide for Venting of Deflagrations

• NFPA 69, Standard on Explosion Prevention Systems

• NFPA 72, National Fire Alarm Code(r)

• NFPA 80, Standard for Fire Doors and Fire Windows

• NFPA 80A, Recommended Practice for Protection of Buildings from Exterior Fire Exposures

• NFPA 85, Boiler and Combustion Systems Hazards Code

• NFPA 86, Standard for Ovens and Furnaces

• NFPA 88A, Standard for Parking Structures

• NFPA 88B, Standard for Repair Garages

• NFPA 90A, Standard for the Installation of Air-Conditioning and Ventilating Systems

• NFPA 92A, Recommended Practice for Smoke-Control Systems

• NFPA 96, Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations

• NFPA 101, Code for Safety to Life from Fire in Buildings and Structures

• NFPA 101A, Guide on Alternative Approaches to Life Safety

• NFPA 101B, Code for Means of Egress for Buildings and Structures

• NFPA 110, Standard for Emergency and Standby Power Systems

• NFPA 115, Recommended Practice on Laser Fire Protection

• NFPA 120, Standard for Coal Preparation Plants

• NFPA 123, Standard for Fire Prevention and Control in Underground Bituminous Coal

Mines

• NFPA 204, Standard for Smoke and Heat Venting

• NFPA 220, Standard on Types of Building Construction

• NFPA 221, Standard for Fire Walls and Fire Barrier Walls

• NFPA 230, Standard for the Fire Protection of Storage

• NFPA 241, Standard for Safeguarding Construction, Alteration, and Demolition Operations

• NFPA 291, Recommended Practice for Fire Flow Testing and Marking of Hydrants

• NFPA 329, Recommended Practice for Handling Releases of Flammable and Combustible Liquids and Gases

• NFPA 471, Recommended Practice for Responding to Hazardous Materials Incidents

• NFPA 472, Standard for Professional Competence of Responders to Hazardous Materials

Incidents

• NFPA 473, Standard for Competencies for EMS Personnel Responding to Hazardous Materials Incidents

• NFPA 900, Building Energy Code

• NFPA 1963, Standard for Fire Hose Connections

• NFPA 5000, NFPA Building Code

• OSHA 29 Code of Federal Regulations Part 1910