Attachment 1 - Specs.pdf

USCGC ANTHONY PETIT (WLM 558)

SPECIFICATION FOR DRYDOCK REPAIRS

FY2024

Developed By: Brenden J Lee

(Rev-0, 30 Oct 2023)

USCGC ANTHONY PETIT (WLM-175) DRYDOCK AVAILABILITY FY2024

ii (Rev-0)

TABLE OF CONTENTS

Revisions Record .......................................................................................................................................... iv Consolidated List of References .................................................................................................................... v Consolidated List of Government-furnished Property ................................................................................ xv Consolidated List of Critical Inspection Items ............................................................................................ xx Principal Characteristics - TENDER ........................................................................................................ xxii General Requirements WORK ITEM 1: Fire Prevention Requirements WORK ITEM 2: Hull Plating, U/W Body, Inspect WORK ITEM 3: Hull Plating, U/W Body, Ultrasonic Testing WORK ITEM 4: U/W Body, Preserve, 100 percent WORK ITEM 5: U/W Body, Preserve, Partial, Condition A WORK ITEM 6: U/W Body, Preserve, Partial, Condition B WORK ITEM 7: U/W Body, Preserve, Partial, Condition C WORK ITEM 8: Hull Plating Freeboard, Preserve, Partial WORK ITEM 9: Hull Plating Freeboard, Preserve, 100 Percent WORK ITEM 10: Appendages, U/W, Leak Test WORK ITEM 11: Appendages, U/W, Internal, Preserve WORK ITEM 12: Chain Lockers, Clean and Inspect WORK ITEM 13: Tanks, Potable Water, Clean and Inspect WORK ITEM 14: Tanks, Ballast, Clean and Inspect WORK ITEM 15: Tanks, Dirty Oil and Waste, Clean and Inspect WORK ITEM 16: Z-Drive Input Drive Shaft, Bearings Inspect WORK ITEM 17: Z-Drive Propulsion Unit, Renew, Drydock WORK ITEM 18: Ship Service Diesel Generator, SSDG, Exhaust Piping, Commercial Clean WORK ITEM 19: Fathometer Transducer, Renew WORK ITEM 20: Vent Ducts, Engine And Motor Room, All, Commercial Cleaning WORK ITEM 21: Vent Ducts, Galley and Pantry Room, All, Commercial Cleaning WORK ITEM 22: Vent Ducts, Laundry Exhaust, Commercial Cleaning WORK ITEM 23: Vent Ducts, All Other, Commercial Cleaning WORK ITEM 24: Sea Valves and Waster Pieces, Overhaul Or Renew WORK ITEM 25: Sea Strainers, All Sizes, Renew WORK ITEM 26: Sea Strainers, Duplex, All Sizes, Overhaul WORK ITEM 27: Sea Bay, Clean and Inspect WORK ITEM 28: Sea Bay, Preserve 100% WORK ITEM 29: Potable Water Pneumatic Tanks, Clean and Inspect WORK ITEM 30: Thruster Unit (General), Overhaul WORK ITEM 31: Hull Fittings (Weight Handling Rigging Hardware), Inspect and Test WORK ITEM 32: Anchor Chains and Ground Tackle, Inspect and Repair WORK ITEM 33: Hull Fittings (Mooring and Towing), Inspect and Test WORK ITEM 34: Chain Locker, Preserve, 100 Percent WORK ITEM 35: Superstructure, Preserve, Partial WORK ITEM 36: Cathodic Protection, Zinc Anodes, Renew, WORK ITEM 37: Drydock WORK ITEM 38: Temporary Services, Provide - Cutter WORK ITEM 39: Sea Trial Performance, Support, Provide WORK ITEM 40: ATON Tie-down, Install WORK ITEM 41: Oily Water Separator, Replace WORK ITEM 42: Crane Winch DCV, Replace iii (Rev-0)

WORK ITEM 43: Thruster Quick Disconnects (QDs), Install WORK ITEM 44: Pump Room, Deck, Partial Preserve WORK ITEM 45: Vents, Preserve and Closures, Renew WORK ITEM 46: Potable Water Deck Connection Piping, Renew WORK ITEM 47: Cargo Hatch, Repair WORK ITEM 48: Vent Space (01-50-0-Q), Deck, Preserve WORK ITEM 49: Cross Deck Winch Kickpipe, Renew WORK ITEM 50: Doppler Speed Log, Upgrade WORK ITEM 51: Directional Control Valve, Upgrade WORK ITEM 52: Sea Strainers, Simplex, All Sizes, Clean and Inspect WORK ITEM 53: Tanks, Ballast, Preserve, 100 Percent WORK ITEM 54: Tanks, Ballast, Preserve, Partial WORK ITEM 55: Tanks, Dirty Oil and Waste, Preserve, 100 Percent, WORK ITEM 56: Tanks, Dirty Oil and Waste, Preserve, Partial, WORK ITEM 57: Tanks, Potable Water Preserve, 100 Percent WORK ITEM 58: Tanks, Potable Water, Preserve, Partial, WORK ITEM 59: Independent NACE Inspector (Level 3), Provide WORK ITEM 60: Tenting, Provide WORK ITEM 61: Hydraulically Operated Cargo Hatch, Inspect and Service WORK ITEM 62: Hydraulic Chain Stoppers, Inspect And Service WORK ITEM 63: Hydraulic Crossdeck Winches, Inspect And Service WORK ITEM 64: Hydraulic Inhaul Winch, Inspect And Service WORK ITEM 65: Mechanical Chain Stoppers, Inspect and Service WORK ITEM 66: Anchor Windlass, Inspect And Service WORK ITEM 67: Towing Bitts, Chocks, and Fairleads, Inspect and Test WORK ITEM 68: Warping Capstan (Aft), Inspect and Service WORK ITEM 69: Single Point Davit, Disassemble and Inspect WORK ITEM 70: Buoy Crane, Inspect And Service WORK ITEM 71: Decks - Exterior, Preserve, Non-Skid Broadcast Grit System WORK ITEM 72: Decks – Exterior (Buoy or Construction Deck), Preserve 100% WORK ITEM 73: Point of Use Potable Water Filters, Install WORK ITEM 74: Flame Detectors, Replace WORK ITEM 75: Vent Duct Systems, Repair WORK ITEM 76: Z-drive Standby Hydraulic and LO Pumps, Overhaul WORK ITEM 77: Drainage Valve and Remote Valve Operator, Renew WORK ITEM 78: MDE & SSDG Exhaust Stack Insulation, Renew WORK ITEM 79: Fuel Oil Piping, Renew WORK ITEM 80: Bilge Pump, Overhaul WORK ITEM 81: Bilges, Preserve WORK ITEM 82: Hull and Structural Plating, General, 12.75 lbs. Steel Plate, Renew WORK ITEM 83: Cargo Hold Deck, Preserve 100% WORK ITEM 84: Ship Service Diesel Generator, Clean and Inspect iv (Rev-0)

REVISIONS RECORD

This page is used to record specification revisions, which may have occurred subsequent to a Revision 0 (Rev-0) package. Information listed is intended to provide contractors and field unit personnel a means to ensure all the current specification revision pages are present when reviewing or utilizing this specification package.

DATE REV# WORK

ITEM#

CHANGES MADE

NOTE : All work item and paragraph numbers listed above for a given revision correspond to same numbers in the previous revision. This revised specification is self-contained with all of the above listed changes incorporated.

v (Rev-0)

CONSOLIDATED LIST OF REFERENCES

The below-listed documents form a part of this specification to the extent specified herein. Approval/publication dates or revision dates/numbers are also identified, to ensure that same document versions are used at the time of specification writing and during contract execution.

All Coast guard drawings, technical publications, and standard specifications will be provided to contractors by the Coast Guard at an appropriate time, or upon request, free of charge. Other Government documents may be accessed – free of charge – from links located on the SFLC website. Commercial sites provide access to their respective documents.

COAST GUARD DRAWINGS

Coast Guard 175-WLM-167-001, Rev L, Structural Closures

Coast Guard Drawing 175 WLM 114-001, Rev D, Shell Appendages

Coast Guard Drawing 175 WLM 130-001, Rev -, Mods to Buoy Deck Incidental to Hawser Pipe Cover

Coast Guard Drawing 175 WLM 130-001, Rev -Mods to Buoy Deck Incidental to Hawser Pipe Cover

Coast Guard Drawing 175 WLM 180-011, Rev F, Sheet 5 Bow Thruster Foundation

Coast Guard Drawing 175 WLM 184-001, Rev A, V850 Transducer Adaptor Ring

Coast Guard Drawing 175 WLM 184-001, Rev-, CRP-V850 Transducer Adapter Ring

Coast Guard Drawing 175 WLM 184-001, V850 Transducer Adaptor Ring

Coast Guard Drawing 175 WLM 185-001, Rev -, Foundation Incidental to Boss 2.2 GPM OWS

Installation

Coast Guard Drawing 175 WLM 201-001, Rev C, Machinery Spaces Arrangement

Coast Guard Drawing 175-WLM 201-2, Rev D, Machinery Removal Routes

Coast Guard Drawing 175 WLM 202-002, Rev G, MPCMS Wiring Data (COED)

Coast Guard Drawing 175 WLM 243-001, Rev -, Propulsion Shafting Arrangement

Coast Guard Drawing 175 WLM 243-002, Rev F, Propulsion Shafting Arrangement

Coast Guard Drawing 175 WLM 245-001, Rev A, Propeller

Coast Guard Drawing 175 WLM 245-002, Rev A, Z-drive Propeller Details, Modified Design

Coast Guard Drawing 175 WLM 256-001, Rev J, Sea Water Cooling System Diagram

Coast Guard Drawing 175 WLM 256-001, Rev J, Seawater Cooling System Diagram

Coast Guard Drawing 175 WLM 256-004, Rev J, Sea Water Cooling System Arrangements and Details

Coast Guard Drawing 175 WLM 256-004, Rev J, Sheets 5 and 13, Seawater Cooling System A & D, Hull

Blocks 940-970

Coast Guard Drawing 175 WLM 256-013, Rev A, Sea Bay Thermometer Installation

Coast Guard Drawing 175 WLM 259-001, Rev A, Combustion Exhaust Diagram

Coast Guard Drawing 175 WLM 259-005, Rev C, Combustion Exhaust A&D, Hull Block 970

Coast Guard Drawing 175 WLM 259-1, Rev A, Combustion Exhaust Diagram

Coast Guard Drawing 175 WLM 259-5, Rev C, Combustion Exhaust A & D Hull Block 970

Coast Guard Drawing 175 WLM 262-001, Rev J, Lube Oil System Diagram

Coast Guard Drawing 175 WLM 262-002, Rev H, Waste Oil System Diagram vi (Rev-0)

Coast Guard Drawing 175 WLM 262-005, Rev G, Lube Oil System A/D – Hull Blocks 910, 930, 940, &

Coast Guard Drawing 175 WLM 320-001, Rev AL, Electrical One-Line Diagram

Coast Guard Drawing 175 WLM 320-004, Rev G, Power System Deck Plan ER and Pump Rm Hull

Block 920

Coast Guard Drawing 175 WLM 320-012, Rev -, Power System Mods Incidental to OWS

Removal/Installation One-Line Diagram

Coast Guard Drawing 175 WLM 505-002, Rev F, Mech Remote Valve Oprs A & D

Coast Guard Drawing 175 WLM 505-003, Rev B, Sea Connection Arrangements

Coast Guard Drawing 175 WLM 508-2, Rev A, Combustion Exhaust Pipe Insulation

Coast Guard Drawing 175 WLM 512-001, Rev E, HVAC Diagram

Coast Guard Drawing 175 WLM 512-1, Rev E, HVAC Diagram

Coast Guard Drawing 175 WLM 512-11, Rev E, HVAC A & D FR 70-50 Main Deck & Above Hull

Block 960

Coast Guard Drawing 175 WLM 512-13, Rev C, HVAC Standard Details and General Instructions

Coast Guard Drawing 175 WLM 512-5, Rev A, HVAC A & D FR 6-FWD Hull Block 901

Coast Guard Drawing 175 WLM 512-6, Rev D, HVAC A & D FR 24-6 Hull Block 910

Coast Guard Drawing 175 WLM 512-8, Rev C, HVAC A & D, FR 61-42, Hull Block 930

Coast Guard Drawing 175 WLM 529-005, Rev E, Ballast System, A/D – Hull Block, 901, 910, 920, 930

Coast Guard Drawing 175 WLM 529-007, Rev F, Main Drainage System, A/D – Hull Block, 901, 910, 920, 930

Coast Guard Drawing 175 WLM 533-001, Rev G, Potable Water System Diagram

Coast Guard Drawing 175 WLM 533-001, Rev H, Potable Water System Diagram

Coast Guard Drawing 175 WLM 533-006, Rev D, Independent Tank Potable Water Hb 950

Coast Guard Drawing 175 WLM 541-001, Rev H, Fuel Oil System Diagram

Coast Guard Drawing 175 WLM 541-003, Rev F, Fuel Oil Service, A/D, Hull Block 940, 970

Coast Guard Drawing 175 WLM 541-005, Rev F, Fuel Oil Transfer System, A/D, Hull Block 940, 970

Coast Guard Drawing 175 WLM 549-001, Rev E, Onboard Lubrication Requirements

Coast Guard Drawing 175 WLM 549-1, Rev E, Onboard Lubrication Requirements

Coast Guard Drawing 175 WLM 561-001, Rev J, Z-drive Hydraulic System Diagram

Coast Guard Drawing 175 WLM 568-2, Rev M, Bow Thruster Assembly (Model 125 Fixed Pitch)

Coast Guard Drawing 175 WLM 573-001, Rev T, Buoy Deck Arrangement

Coast Guard Drawing 175 WLM 573-001, Rev T; Buoy Deck Arrangement

Coast Guard Drawing 175 WLM 573-050, Rev A, Hydraulic Piping Installation for Chain Stopper

Coast Guard Drawing 175 WLM 573-051, Rev B, Chain Stopper Structural Modifications for Hydraulic

Roller Assembly

Coast Guard Drawing 175 WLM 573-8, Rev D, ATON Tie Downs

Coast Guard Drawing 175 WLM 581-001, Rev E, Anchor Handling System Arrangement

Coast Guard Drawing 175 WLM 581-001, Rev F, Anchor Handling System Arrangement

Coast Guard Drawing 175 WLM 581-001, Rev F, Anchor Handling System

Coast Guard Drawing 175 WLM 582-001, Rev D, Mooring and Towing, A & D

Coast Guard Drawing 175 WLM 593-002, Rev H, Oily Bilge System Diagram

Coast Guard Drawing 175 WLM 593-002, Rev H, Oily Bilge Water System Diagram vii (Rev-0)

Coast Guard Drawing 175 WLM 593-008, Rev E, Oily Bilge Water System, A/D Hull Block 910, 920, 930, 940

Coast Guard Drawing 175 WLM 593-013, Rev C, Oily Water Separator A&D

Coast Guard Drawing 175 WLM 593-014, Rev A, OWS System Operating Instructions BOSS 2.2T-107-

YM

Coast Guard Drawing 175 WLM 601-001, Rev L, General Arrangement and Inboard and Outboard

Profiles

Coast Guard Drawing 175 WLM 601-001, Rev R; General Arrangement Inboard and Outboard Profiles

Coast Guard Drawing 175 WLM 601-001, Rev T, General Arrangement Inboard & Outboard Profiles

Coast Guard Drawing 175 WLM 601-001, Rev T, General Arrangement Inboard and Outboard Profiles

Coast Guard Drawing 175 WLM 601-002, Rev H, Booklet of General Drawings (IDA LEWIS)

Coast Guard Drawing 175 WLM 601-003, Rev F, Booklet of General Drawings (552-564)

Coast Guard Drawing 175 WLM 601-003, Rev F, Booklet of General Plans

Coast Guard Drawing 175 WLM 601-003, Rev F, Booklet of General Plans

Coast Guard Drawing 175 WLM 601-003, Rev F, Booklet Of General Plans

Coast Guard Drawing 175 WLM 601-003, Rev N, Booklet of General Plans

Coast Guard Drawing 175 WLM 601-1, Rev N, Arrangement, Inboard And Outboard Profiles

Coast Guard Drawing 175 WLM 601-1, Rev T, Arrangement, Inboard And Outboard Profiles

Coast Guard Drawing 175 WLM 633-001, Rev D, Cathodic Protection

Coast Guard Drawing 175 WLM 635-001, Rev F, Hull Thermal and Acoustic Insulation Schedule

Coast Guard Drawing 175 WLM 635-001, Rev F, Hull, Thermal, & Acoustic Insulation Schedule

Coast Guard Drawing 175 WLM 801-001, Rev A, Hull Lines

Coast Guard Drawing 175 WLM 801-003, Rev A, Curves of Form

Coast Guard Drawing 175 WLM 801-006, Rev H, Docking Plan

Coast Guard Drawing 175 WLM 801-006, Rev J, Docking Drawing

Coast Guard Drawing 175 WLM 801-006, Rev J, Docking Plan

Coast Guard Drawing 175 WLM 801-015, Rev C, Scantlings, Decks & Platforms

Coast Guard Drawing 175 WLM 801-019, Rev C, Shell Expansion

Coast Guard Drawing 175 WLM 801-19, Rev C; Shell Expansion

Coast Guard Drawing 175 WLM 920-001, Rev K, Hull Block 920 Panels

Coast Guard Drawing 175 WLM 940-001, Rev J, Hull Block 940 Panels

Coast Guard Drawing 175 WLM 940-002, Rev K, Hull Block 940 Modules

Coast Guard Drawing 175 WLM 940-004, Rev J, Hull Block 940 - Transverse Frames & BHD

Coast Guard Drawing 175 WLM-259-4, Rev D, Combustion Exhaust A & D, Hull Block 940

Coast Guard Drawing 175-WLM 533-1, Rev H, Potable Water System Diagram

Coast Guard Drawing 175-WLM 533-3, Rev G, POTABLE WATER SYSTEM A/D HULL BLOCK

910, 920, 930, 940, 950

Coast Guard Drawing 175-WLM 561-1, Rev J, Z-Drive Hydraulic System Diagram

Coast Guard Drawing 175-WLM 568-001, Rev B, Bow Thruster Arrangement & Detail

Coast Guard Drawing 175-WLM 256-001, Rev H, Seawater Cooling System Diagram

Coast Guard Drawing 175-WLM 256-001, Rev J, Seawater Cooling System Diagram

Coast Guard Drawing 175-WLM 256-001, Rev K, Seawater Cooling System Diagram viii (Rev-0)

Coast Guard Drawing 175-WLM 256-003, Rev A, Seawater Cooling System, Fr 61 Fwd Blocks 910, 920, Coast Guard Drawing 175-WLM 256-003, Rev D, Seawater Cooling System, Fr 61 Fwd Blocks 910, 920, Coast Guard Drawing 175-WLM 256-004, Rev J, Seawater Cooling System A & D, Hull Blks 940-970

Coast Guard Drawing 175-WLM 256-012, Rev B, ASW System Piping Modifications

Coast Guard Drawing 175-WLM 436-1, Rev H, Fire & Smoke Detection System Block, Isometric, and

Elementary Wiring Diagram (Circuit SM)

Coast Guard Drawing 175-WLM 512-1, Rev E, HVAC Diagram

Coast Guard Drawing 175-WLM 512-6, Rev D, HVAC A & D, Frame 24-6, Hull Block 910

Coast Guard Drawing 175-WLM 516-004, Rev A, HVAC Refrigeration System Piping Arrangement &

Details

Coast Guard Drawing 175-WLM 549-001, Rev E, Onboard Lubrication Requirements

Coast Guard Drawing 175-WLM 549-1, Rev C, Onboard Lubrication Requirements

Coast Guard Drawing 175-WLM 551-5, Rev E, Compressed Air System a/D Hull Block 940, 950

Coast Guard Drawing 175-WLM 556-1, Rev J, Hydraulic System Diagram

Coast Guard Drawing 175-WLM 568-002, Rev N, Bow Thruster Detail

Coast Guard Drawing 175-WLM 573-001, Rev R, Buoy Deck Arrangement

Coast Guard Drawing 175-WLM 573-008, Rev C, Aton Tie Downs

Coast Guard Drawing 175-WLM 601-001, Rev T, General Arrangement Inboard and Outboard Profiles

Coast Guard Drawing 175-WLM 635-001, Rev F, Hull Thermal & Acoustic Insulation Schedule

Coast Guard Drawing 175-WLM 635-1, Rev F, Hull Thermal & Acoustic Insulation Schedule

Coast Guard Drawing 175-WLM 801-015, Rev C, Scantlings, Decks & Platforms

Coast Guard Drawing 175-WLM 920-001, Rev K, Hull Block 920 Panels

Coast Guard Drawing 175-WLM 930-001, Rev K, Hull Block 930 Panels

Coast Guard Drawing 175-WLM-320-001, Rev AP, Electrical One-Line Diagram

Coast Guard Drawing 175-WLM-320-1, Rev AR, Electrical One-Line Diagram

Coast Guard Drawing 175-WLM-320-2, Rev G, Power System Deck Plan Frame 24 FWD, Hull Blocks

910 & 901

Coast Guard Drawing 175-WLM-424-003, Rev. -, Doppler Speed Log System Replacement, Ripout, Installation, Arrangement, Wiring and Details

Coast Guard Drawing 175-WLM-437-007, Rev R, Buoy Dk Control Sys Block, ISO & Elem Wrg Diag

Coast Guard Drawing 175-WLM-437-7, Rev R, Buoy DK Control SYS Block, ISO & ELEM WRG Diag

Coast Guard Drawing 175-WLM-505-002 Rev F Mechanical Remote Valve Operators Arrangement and

Details

Coast Guard Drawing 175-WLM-529-002 Rev G Main Drainage System Diagram

Coast Guard Drawing 175-WLM-573-013, Rev -, Replacement DCV Amplifier Card Wiring Diagram

Coast Guard Drawing 175-WLM-635-1, Rev F, Hull Thermal & Acoustic Insulation Schedule

Coast Guard Drawing FL 2605-031, Rev D, Mechanical Chain Stopper, 1-7/8" Buoy Chain

Coast Guard Drawing FL 2605-034, Rev D, Mechanical Chain Stopper Repair Kit: 1-7/8", 1-5/8" & 1-

1/4"

Coast Guard Drawing FL 533-001, Rev B, Placard Potable Water Flush

Coast Guard Drawing FL 533-002, Rev A, Point of Use Water Filter Install ix (Rev-0)

Coast Guard Drawing FL 7101-573, Rev L, Buoy Chain Winch Assy Model CW1

Coast Guard Fleet Drawing FL 2804-12, Rev -, U.S.C.G. Emblem

Coast Guard Fleet Drawing FL 2804-22, Rev-, Consolidated Visual ID for Cutters

Coast Guard Fleet Drawing FL-2605-029, Rev L, Chain Stopper System – Rising Sheave Assembly

COAST GUARD PUBLICATIONS

Coast Guard Commandant Instruction (COMDTINST) 9077.1 (series), Equipment Lockout/Tags-Plus

Instruction

Coast Guard Commandant Instruction (COMDTINST) M10360.3, Jun 2006, Coatings and Colors

Manual

Coast Guard Maintenance Procedure Card (MPC) A-A-14033, Dec 2017, Buoy Chain Winch Wire Rope

Weight

Coast Guard Technical Publication (TP) 3498, Section A, Jul 2015, Buoy Chain Winch

Coast Guard Technical Publication (TP) 3498, SWBS 573, Aug 2019, Buoy Chain Winch

Coast Guard Technical Publication (TP) 3605A, Nov 2007, MPCMS Operating Manual (Volume 1)

Coast Guard Technical Publication (TP) 3605B, SWBS 86; Section B; Machinery Plant Control &

Monitor System (MPCMS) Z-Drive Direction Indicator System Technical Manual

Coast Guard Technical Publication (TP) 3610, Section 167-A, July 2002, Power Operated Cargo Hatch, Coastal Buoy Tender, Model No. D-WK-787

Coast Guard Technical Publication (TP) 3610, Section 167-A, Nov 2005, Hydraulic Cargo Hatch - Model

No. D-WK-787

Coast Guard Technical Publication (TP) 3616A, Manufacturer's Instruction Book – SWBS Group(s) 310

Coast Guard Technical Publication (TP) 3616B, Manufacturer's Instruction Book – SWBS Group(s) 310

Coast Guard Technical Publication (TP) 3621, SWBS 436, June 2020, Fire Detection System - Operation, Installation and Maintenance Manual, July 2020

Coast Guard Technical Publication (TP) 3626, SWBS 529, 09 Nov 1999, Bilge Pump (Blackmer)

Coast Guard Technical Publication (TP) 3628, Mar 2017; Vol 4 of 9, Instruction Manual, Bow Thruster

Coast Guard Technical Publication (TP) 3628, SWBS 568, Section A, March 2017, Bow Thruster –

(Bird-Johnson Company)

Coast Guard Technical Publication (TP) 3630, 07-JAN-97, Manufacturers Instruction Book-SWBS

Group(s) 573

Coast Guard Technical Publication (TP) 3630, SWBS 573, Section A (573A), Jun 2015, Manufacturer's

Instruction Book-SWBS Group 573, Buoy Crane

Coast Guard Technical Publication (TP) 3631, Mar 2007, Manufacturer’s Instruction Book-SWBS

Group(s) 573-581, Section B, Cross Deck Winch – Appleton Marine Model BMD-463

Coast Guard Technical Publication (TP) 3631, Section 581-A, Sep 2013, Manufacturer's Instruction

Book-SWBS Groups 573-581, Anchor Windlass

Coast Guard Technical Publication (TP) 3632, March 2014, Chapter 583, Section C, Technical Manual for Slewing Arm Davit Model D6000CT

Coast Guard Technical Publication (TP) 3632, Section 582-A, March 2014, Manufacturer's Instruction

Book-SWBS Groups 582-583, Aft Capstan

Coast Guard Technical Publication (TP) 3653, Jul 2013; SWBS 245, Section A; Z-Drive - Model 1350-H

Coast Guard Technical Publication (TP) 3653, Jul 2013; SWBS 245, Section A; Z-DRIVE - MODEL

1350-H

Coast Guard Technical Publication (TP) 3653, Jul 2013; SWBS 245, Section A; Z-drive - Model 1350-H x (Rev-0)

Coast Guard Technical Publication (TP) 3749, 26-APR-05, 1-7/8 Inch ATON Mechanical Chain Stopper

Coast Guard Technical Publication (TP) 3939, SWBS 573-A, Apr 2007, Rising Sheave Chain Stopper

Coast Guard Technical Publication TP-10500, Doppler Sonar – Model DS-60

Coast Guard Technical Publication TP-3446, Doppler Speed Log, Model SRD-500 Dual Axis

Fire Prevention and Response

NAVSEA Drawing 804-5773931, Rev A, Acoustic & Thermal Insulation For Compartments Installation

Details

NAVSEA Dwg 2803-980209, Plates, Label

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 0000, 2022, General

Requirements

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 0740, 2022, Welding and Allied

Processes

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 3041, 2022, Shipboard

Electrical Cable Test

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 3042, 2022, Shipboard

Electrical Cable Removal, Relocation, Splice, Repair, and Installation

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 6310, 2022, Requirements for

Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2014, General

Requirements

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2022, General

Requirements

Surface Forces Logistics Center Standard Specification 0450 (SFLC Std Spec 0450), 2022, Electrical

Power for Contractor's Tools & Equipment

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2022, Welding and

Allied Processes

Surface Forces Logistics Center Standard Specification 0740, (SFLC Std Spec 0740) 2022, Welding and

Allied Processes

Surface Forces Logistics Center Standard Specification 3020 (SFLC Std Spec 3020), 2022, Overhaul AC

Electrical Motors

Surface Forces Logistics Center Standard Specification 3041 (SFLC Std Spec 3041), 2022, Shipboard

Electrical Cable Test

Surface Forces Logistics Center Standard Specification 3041, (SFLC Std Spec 3041) 2022, Shipboard

Electrical Cable Test

Surface Forces Logistics Center Standard Specification 3042 (SFLC Std Spec 3042), 2022, Shipboard

Electrical Cable Removal, Relocation, Splice, Repair, and Installation

Surface Forces Logistics Center Standard Specification 3042, (SFLC Std Spec 3042) 2022, Shipboard

Electrical Cable Removal, Relocation, Splice, Repair and Installation

Surface Forces Logistics Center Standard Specification 3100 (SFLC Std Spec 3100), 2022, Inspect, Test and Recondition AC Synchronous Machines In-Place

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2014, Auxiliary

Machine Systems

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2022 Auxiliary

Machine Systems xi (Rev-0)

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2022, Auxiliary

Machine Systems

Surface Forces Logistics Center Standard Specification 5100 (SFLC Std Spec 5100), 2022, Clean

Shipboard Ventilation Systems

Surface Forces Logistics Center Standard Specification 5550 (SFLC Std Spec 5550), 2022, Fire

Prevention and Response

Surface Forces Logistics Center Standard Specification 5550 (SFLC Std Spec 5550), Latest Version, Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2022, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6310, (SFLC Std Spec 6310) 2022, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 8634 (SFLC Std Spec 8634), 2022, Drydocking

Surface Forces Logistics Center Standard Specification 8635 (SFLC Std Spec 8635), 2022, Temporary

Services

Surface Forces Logistics Center Standard Specification 8636 (SFLC Std Spec 8636), 2022, Temporary

Hull Accesses

OTHER REFERENCES

American Bureau of Shipping (ABS) Approved Chain, Accessory and Bar Manufacturing Facilities List, Oct 2016

American National Standards Institute/American Water Works Association (ANSI/AWWA) C652, 2002, Disinfection of Water-Storage Facilities

American National Standards Institute/American Water Works Association (ANSI/AWWA) C652, 2011, Disinfection of Water-Storage Facilities

American National Standards Institute/American Water Works Association (ANSI/AWWA) C652, 2019, Disinfection of Water-Storage Facilities

American National Standards Institute/NSF International (ANSI/NSF) 61, 2008, Drinking Water System

Components - Health Effects

American National Standards Institute/NSF International (ANSI/NSF) 61, 2015, Drinking Water System

Components - Health Effects

American Society of Mechanical Engineers (ASME) B16.34, 2017, Valves-Flanged, Threaded, and

Welding End

Appleton Marine Control Valve Retrofit Manual 20793

ASTM International (ASTM) A106, 2015, Standard Specification for Seamless Carbon Steel Pipe, for

High-Temperature Service

ASTM International (ASTM) D1330, 2004, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D1330, 2010, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D1330, 2015, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D3359, 2009, Standard Test Methods for Measuring Adhesion by Tape

Test

ASTM International (ASTM) D4138, 2013, Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means

ASTM International (ASTM) D5363, 2008, Standard Specification for Anaerobic Single Component

Adhesives (AN) xii (Rev-0)

ASTM International (ASTM) D5363, 2016, Standard Specification for Anaerobic Single-Component

Adhesives (AN)

ASTM International (ASTM) F683, 2010, Standard Practice for Selection and Application of Thermal

Insulation for Piping and Machinery

ASTM International (ASTM) F992, 2006, Standard Specification for Valve Label Plates

ASTM International (ASTM) F992, 2017, Standard Specification for Valve Label Plates

Coast Guard Commandant Instruction (COMDTINST) M10360.3, Jun 2006, Coatings and Colors Manual

Code of Federal Regulations (CFR) Title 29, Part 1910, Occupational Safety and Health Standards

Code of Federal Regulations (CFR) Title 29, Part 1915, 2014, Occupational Safety and Health Standards for Shipyard Employment

Code of Federal Regulations (CFR) Title 29, Part 1915, 2022, Occupational Safety and Health Standards for Shipyard Employment

Code of Federal Regulations (CFR) Title 29, Part 1915, Occupational Safety and Health Standards for

Shipyard Employment

Code of Federal Regulations (CFR) Title 29, Part 1915, Occupational Safety and Health Standards for

Shipyard Employment

Code of Federal Regulations (CFR) Title 40, Protection of the Environment

Commercial Item Description (CID) A-A-59313, Nov 2003, Thread Compound; Anti-seize, Zinc Dust-

Petrolatum

Commercial Item Description (CID) A-A-59323, Rev A, Cloths, Cleaning, Low-Lint

Federal Specification (Fed Spec) HH-P-151, Mar 1991, Packing; Rubber-Sheet, Cloth-Insert

Federal Specification (Fed Spec) RR-C-271, Rev E, Mar 2016, Chains and Attachments, Carbon and

Alloy Steel

IEEE STD 45-2002, Recommended Practice for Shipboard Electrical Installations

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-61, 2013 Edition, Pressure Testing Of Steel Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-67, 2017 Edition, Butterfly Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-72, 2018 Edition, Ball Valves with Flanged or Butt-Welding Ends for General Service

Manufacturers' Standardization Society of the Valve and Fittings Industry (MSS) SP-80, 2013 Edition, Bronze Gate, Globe, Angle and Check Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), SP-58, 2009, Pipe

Hangers and Supports – Materials, Design, Manufacture, Selection, Application and Installation

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), SP-58, 2018, Pipe

Hangers and Supports – Materials, Design, Manufacture, Selection, Application and Installation

MIL-A-18001, May 2005, Anodes, Sacrificial Zinc Alloy (Commercially Accepted - ASTM B418)

MIL-A-22262, Mar 1996; Abrasive Blasting Media Ship Hull Blast Cleaning

MIL-C-24633, Oct 2014, Chain, Stud Link, Anchor, Low Alloy Steel, Flash Butt Welded

MIL-DTL-15024, General Specification for Plates, Tags, and Bands for Identification of Equipment

MIL-DTL-23549, Sep 2016, Grease, General Purpose

MIL-DTL-24244, Insulation Material, With Special Corrosion, Chloride, and Fluoride Requirements

MIL-F-24402, May 1995, Filters (Hydraulic), Filter Elements (High Efficiency), and Filter Differential

Pressure Indicators, General Specification xiii (Rev-0)

MIL-I-16411, Insulation Felt, Thermal, Glass Fiber

MIL-I-3064, Mar 1991, Insulation, Electrical, Plastic-Sealer

MIL-PRF-16173, Sep 2006, Corrosion Preventive Compound, Solvent Cutback, Cold-Application

MIL-PRF-24176 , Oct 2004, Cement, Epoxy, Metal Repair And Hull Smoothing (Metric)

MIL-PRF-24647, 2013, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-24647, Jun 2006, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-24647, Jun 2006, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-S-45180, 1998, Sealing Compound, Gasket, Hydrocarbon Fluid and Water Resistant

MIL-S-45180, 1998; Sealing Compound, Gasket, Hydrocarbon Fluid and Water Resistant

MIL-STD-2003-3, Sep 2009, Electric Plant Installation Standard Methods for Surface Ships &

Submarines (Penetrations)

MIL-STD-2003-4, Sep 2009, Electric Plant Installation Standard Methods for Surface Ships &

Submarines (Cableways)

MIL-Y-1140, Yarn, Cord, Sleeving, Cloth, And Tape- Glass

Naval Sea Systems Command (NAVSEA) Underwater Ship Husbandry Manuals (UWSH) S0600-AA-

PRO-160, Nov 2011, Chapter 16, Cofferdams

NAVSEA Technical Publication T9074-AD-GIB-010/1688, (TP 1688), July 2012, Requirements for

Fabrication, Welding, and Inspection of Submarine Structure

Recovered Energy, Inc, BOSS 107 Separator System Operation & Maintenance Manual – YM Model

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) C6183, 2013, Cork and

Rubber Composition Sheet; For Aromatic Fuel and Oil Resistant Gaskets

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) C6183, 2019, Cork and

Rubber Composition Sheet; For Aromatic Fuel And Oil Resistant Gaskets

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) C6183B, 2019, Cork and Rubber Composition Sheet; For Aromatic Fuel and Oil Resistant Gaskets

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) G-6032, 2014, Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) G-6032, 2020 Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric

Society of Automotive Engineers (SAE) AMS-G-6032, August 2012, Grease, Plug Valve, Gasoline and

Oil Resistant, NATO Code Number G-363, Metric

The Society for Protective Coatings (SSPC) Paint Application Specification No. 1 (SSPC-PA 1), Shop, Field, and Maintenance Painting of Steel

The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 1 (SSPC-SP 1), 2004, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 1 (SSPC-SP 1), 2015, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 1 (SSPC-SP 1), 2016, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.1 (SSPC-SP 1), 2015, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.1 (SSPC-SP 1), 2016, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.1 (SSPC-SP 1), Solvent

Cleaning xiv (Rev-0)

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2004, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2012, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2016, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.3 (SSPC-SP 3), 2004, Power Tool Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.3 (SSPC-SP 3), Power

Tool Cleaning)

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.6 (SSPC-SP 6), Commercial Blast Cleaning

The Society for Protective Coatings (SSPC), January 2015, Paint Application Specification No. 2 (PA-2), Procedure for Determining Conformance to Dry Coating Thickness Requirements

The Society for Protective Coatings (SSPC), Paint Application Specification No. 2 (PA-2), Procedure for

Determining Conformance to Dry Coating Thickness Requirements

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation

Standard SSPC-SP 10/NACE No. 2, 2007, Near-White Metal Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation

Standard SSPC-SP 10/NACE No.2, 2007, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation

Standard SSPC-SP 6/NACE No. 3, 2007, Commercial Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation

Standard SSPC-SP 7/NACE No.4, 2007, Brush-Off Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation

Standard SSPC-SP WJ-2, 2012, Waterjet Cleaning of Metals – Very Thorough Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation

Standard SSPC-SP WJ-2/NACE WJ-2, 2012, Waterjet Cleaning of Metals – Very Thorough

Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation

Standard SSPC-SP WJ-4/NACE WJ-4, 2012, Waterjet Cleaning of Metals – Light Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation

Standard SSPC-SP 10/NACE No. 2, 2004, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation

Standard SSPC-SP 10/NACE No. 2, 2007, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation

Standard SSPC-SP 12/NACE No. SSPC-SP 12/NACE No.5, Surface Preparation and Cleaning of

Steel & Other Hard Materials by High and Ultrahigh Pressure Water Jetting Prior to Recoating

The Society for Protective Coatings SSPC-SP 10/NACE No.2, Near-White Blast Cleaning xv (Rev-0)

CONSOLIDATED LIST OF GOVERNMENT-FURNISHED PROPERTY

The following is a list of property, which the Government will furnish. This list supersedes any other material obligations indicated or implied by referenced drawings.

WORK

ITEM

MTI ITEM DESCRIPTION NSN/PN QTY ESTIMATED

COST

($/UNIT)

17 Y Starboard Z-drive

(CCW rotation)

NSN: 2010-21-920-0919 1 ea. 500,250.00

17 Y Port Z-drive (CW rotation)

NSN: 2010-21-920-0899 1 ea. 500,250.00

17 Y Z Drive Alignment Tool NSN: 5220-01-F16-4720 1 ea. 3600.00

17 N Thrustmasters Technical

Representative

N/A N/A N/A

19 N ***Fathometer

Transducer, Shallow

Water, 50-200 kHz

(Airmar Technology

SS505)

NSN: 5845-01-470-2500 1 ea. 343.63

25 N **8” Simplex Strainer BF-150B, with T-bolt hinged cover)

2 ea. 20,000.00

25 N **3” Duplex Strainer NSN: 4730-01-643-2221 PN:

3-792FB (Mueller)

1 ea. 10,400.00

30 N Seal Kit, Thruster NSN: 2010-01-555-9048 1 ea. 4376.00

30 N Anode, Zinc NSN: 5365-01-495-5350 9 ea. 113.75

30 N **Seal Spacer

(B125SM44178)

NSN: 2010-01-495-6823 1 ea. 700.00

30 N **Shaft Sleeve NSN: 2010-01-495-2638 1 ea. 5702.40

37 Y *Transducer Cover

Plate

N/A 2 ea. 50.00

40 N Coast Guard (C-G)

CGDR50TDRASS01

Flush Pad-eye

Assembly: Coast Guard

(C-G) (CGDR50T01)

D-Ring (rated load

12,300 lbs.), welded strap, fabricated bowl.

NSN# 2020-01-682-7587 51

41 N Boss 2.2 GPM OWS NSN: 4330-01-F13-3461 PN:

BOSS 2.2T-107 YM

1 ea. 14,300.00

42 N HDRAULIC

CONTROL VALVE

ASSEMBLY PARTS

KIT

PN: AMD-2633 ACN 4810-

01-F18-5588

1 15,061.00

50 N Main Display Unit NSN: 7025-01-678-5218 PN:

DS600

3 ea $2,525.00

50 N Electronics Distribution

Unit

NSN: 5895-01-678-5147 PN:

DS610

3 ea $6,670.00

50 N Electronics Transceiver NSN: 5845-01-678-5160 PN: 1 ea $9,750.00 xvi (Rev-0)

Unit DS620

50 N Gate Valve Assembly NSN: 4820-01-678-5058 PN:

DS661

1 ea $15,750.00

50 N Dual-Axis Transducer NSN: 5848-01-678-5056 PN:

DS630-30

1 ea $7,700.00

50 N Doppler Shell Ring NSN: 5340-01-F19-5622 PN:

DS661-1

1 ea $5,225.00

50 N Furuno 7-Pin Cable NSN: 5995-01-530-4744 PN:

000-154-028

1 ea $82.40

51 N Directional Control

Valve (DCV)

NSN: 4810-01-F19-5719 PN:

4WRE10E75-2X/G24K4/V

1 ea. 1748.00

51 N Amplifier Card NSN: 5996-01-F19-5720 PN:

VT-VRPA2-2-1X/V0/T1

1 ea. 1552.00

51 N Mating Connector, 4P

G4WIF PG7 SW

NSN: 5935-01-F19-5722 PN:

R900023126

1 ea. 46.00

62 N Repair Kit Assembly NSN: 2040-01-496-9418 2 ea. 1,968.67

62 N Rod Seal Repair Kit

(FL-2605-29 PC#37)

NSN: 2040-01-496-9422 2 ea. 3,030.07

62 N Repair Kit, Cable Chain

(Includes Pads) (FL-

2605-29 PC#36)

NSN: 3020-01-538-0684 16 ea. 257.99

62 N Cylinder Assembly

Actuating, Linear

NSN: 3040-01-496-9424 2 ea. 1,969.24

63 N Hydraulic Brake

Assembly

NSN: 2530-01-550-7474 4 ea. 460.69

63 N Winch Gear Box

Assembly

NSN: 3010-01-F16-4570 PN:

SK9052AZ-SAEB-31.4-H1

(Nord Gear Corp) or YMD-

7914 (Appleton Marine Inc)

4 ea. 1,000.00

63 N Hydraulic Motor NSN: 4320-01-470-8467 4 ea. 478.90

63 N Wire Rope NSN: 4010-01-620-9604 4 ea. 577.95

63 N Counter Balance Valve NSN: 4820-01-324-4269 8 ea. 107.50

63 N Shuttle Valve NSN: 4820-01-317-2748 8 ea. 34.78

63 N Needle Valve NSN: 4820-01-329-0051 4 ea. 38.00

63 N **Directional Control

Valve

NSN: 4810-01-543-3252 4 ea. 4,959.95

63 N Electrical Connector, Hirshmann

NSN: 5935-01-640-6747 8 ea. 32.00

64 N Roller bearing Unit NSN: 3130-01-504-4363 2 ea. 4,012.00

64 N Grease seal NSN: 5330-01-462-5544 4 ea. 79.25

64 N Level wind pivot bushing

NSN: 3120-01-621-2293 1 ea. 1,139.00

64 N Level wind thrust bearing

NSN: 3120-01-621-2300 2 ea. 483.30

64 N Rexroth DCV NSN: 4810-01-507-0037 1 ea. 208.29

64 N Rexroth Sandwich Flow

Control

NSN: 4810-01-505-9289 1 ea. 250.00

64 N Sun Sandwich Relief

Valves

NSN: 4820-01-439-2451 2 ea. 900.00 xvii (Rev-0)

64 Y Level Wind Hydraulic

Cylinder

NSN: 3040-01-441-3721 1 ea. 7,423.00

64 N 3:1 Pilot Ratio, Vented

Counterbalance Valve

Assembly

NSN: 4820-01-563-5841 1 ea 98.70

64 N Fully Adjustable Needle

Valve

NSN: 4820-01-416-0579 1 ea 48.75

64 N Wire Rope Assembly NSN: 4010-01-646-6972 1 ea. 500.00

64 Y **Hydraulic Motor NSN: 4320-01-445-2248 1 ea 23,998

64 N **Pump, Hydraulic

Ram, Hand Driven

NSN: 4320-01-286-4065 1 ea. 419.77

64 N **Cylinder Pin NSN: 5315-01-515-9847 1 ea 500.00

64 N **Cylinder Pin NSN: 5315-01-515-9912 1 ea 520.00

65 N Hardware Kit, Pins NSN: 2030-01-485-7209 2 ea. 528.47

65 N Hardware Kit, Mechanical

NSN: 2030-01-485-7215 2 ea. 538.91

66 N Anchor Windlass

Overhaul kit

NSN: 5430-01-546-4684 1 ea. 9,677.05

66 N Ball Valve NSN: 4820-01-013-3430 1 ea. 38.55

66 N Valve, Counterbalance NSN: 4820-01-F16-4571 PN:

CBEH-LKN-BCL Sun

Hydraulics Corp

1 ea. 202.85

66 Y ** Motor, Hydraulic NSN: 4320-01-419-3520 1 ea. 2,577.98

66 N ** Valve, Linear, Directional Control

NSN: 4810-01-511-3173 1 ea. 2,343.85

66 Y Hydraulic Brake NSN: 2530-01-F14-4033 P/N:

90B3C4G087

1 ea 1,189.44

69 N Swing Brake Seal Kit NSN: 2030-01-351-2820 2 ea 138.80

69 N Swing Brake Disc &

Bearing Kit

NSN: 2030-01-349-9486 2 ea 937.70

69 N Wire Rope Assembly, Single Leg

NSN: 4010-01-602-8365 1 ea. 234.00

69 Y **Winch Assembly NSN: 2030-01-505-1581 1 ea. 17,454.50

70 N Wire Rope, Crane Aux

Fall

NSN: 3950-01-617-1692 1 ea 522.54

70 N Wire Rope, Crane Main

Fall

NSN: 3950-01-617-1700 1 ea 1,275.49

70 N Luff Cylinder Seal kit NSN: 5330-01-433-6307 1 ea 357.99

70 N Holding Valve NSN: 4810-01-353-0586 2 ea 67.33

70 N Shuttle Valve NSN: 4820-01-317-2748 2 ea 24.32

70 N Needle Valve NSN: 4820-01-329-0051 1 ea 38.11

70 Y Valve Assembly, Manifold

NSN: 4810-01-506-7738 1 ea. 19,892.60

70 N Bushing, Heel NSN: 5365-01-F12-2920 4 ea 67.00

70 N Hydraulic swivel seal kit

NSN: 4730-01-566-2864 1 ea 1,298.00

70 N **Pin, Heel NSN: 5315-01-500-6931 2 ea 2,463.45

70 N **Hand pump w/

Stainless Steel Option, NSN: 4320-01-517-1444 1 ea 1,724.57 xviii (Rev-0)

P18

70 N **Plate, Backing, Brake

(Item 231 and 234)

NSN: 3040-00-119-9848 2 ea 1,500.40

70 N **Plate, Brake (Item

232)

NSN: 3040-01-068-7647 1 ea. 377.00

70 N **Driver Plate (Item

233)

NSN: 3040-01-F14-3994 1 ea. 138.34

70 N Packing Assortment, Preformed

NSN: 5330-01-191-2622 1 ea. 10.94

70 N Disc-Friction, Brake NSN: 3040-01-051-3606 1 ea. 15.74

70 N **Spring, Helical, Comp

NSN: 5360-01-268-0044 12 ea 12.12

70 N PD12C Seal kit NSN: 2590-01-398-5741 1 ea 147.76

70 N **Disc, Steel NSN: 2530-01-066-9585 1 ea 38.38

70 N **Master brake rebuild kit

NSN: 5330-01-F16-4572 PN:

98-015-3001 (Eskridge Inc)

3 ea 556.39

70 N Aux Hoist Hook

(Overhaul Ball)

NSN: 4030-01-572-3945 1 ea 2,800.00

70 Y Block, Tackle NSN: 3940-01-566-2929 1 ea 3,806.87

70 N **Relief Valve

Cartridge

NSN: 4820-01-481-7116 PN:

RPIC-LAN (Sun Hydraulics

Inc)

1 ea 117.35

70 N **Control Stand

Selector Valve

Assembly

NSN: 4730-01-507-3516 1 ea 1,247.94

70 N **Bushing, Luff

Cylinder

NSN: 3120-01-363-7629 4 ea 89.53

70 N **Pin, Luff Cylinder NSN: 5315-01-F12-2922 PN:

MMD-2232

2 ea 2,432.30

70 Y **Valve Assembly, Directional Control

NSN: 4810-01-F17-5027 1 ea. 14,806.50

73 N Water Filter Assembly, (3M) (ACN) 44330-01-

F20-5959

PN: DWS160-L NSN: 6 ea. 160.00

73 N Water Filter Element, (3M)

PN: 56134-44 6 ea. 180.00

73 N Placard - Potable Water

Flush

N/A 8 ea. 50.00

74 Y Semiconductor Device, Photo

NSN: 5961-01-599-4004 PN:

20/20MI-11SF

9 ea. 1,489.00

74 N Bracket, Mounting NSN: 5340-01-599-4015 PN:

20/20-005 (ST.ST.316L)

9 ea. 45.55

80 N **CL A REPAIR KIT,

GPXL4

957710 1 ea. $6,089.06

80 N **VALVE LG4 452001 1 ea. $290.00

80 N **BALL BRG SGL

ROW 306

903150 1 ea. $56.20

80 N **DOMESTIC

BEARING

903153 3 ea. $28.34 xix (Rev-0)

80 N **PINION 21T 18P

FOOTE 2KF HRA

915127 1 ea. $751.00

80 N **OIL SEAL 331910 1 ea. $18.85

80 N **OIL SEAL 331923 1 ea. $28.10

80 N **GASKET CL PLATE

HRA W/HX HD

814002 1 ea. $24.20

80 N **GASKET HRA1 814000 1 ea. $15.40

80 N **SPACER RING HRA

.118 WIDE

374004 1 ea. $38.60

80 N **SPACER RING-

REDUCER A

374001 1 ea. $63.60

80 N **RETAINING RING 903618 1 ea. $3.91

80 N **RETAINING RING

HRA

374003 2 ea. $45.40

80 N **CPLG HALF L110

LVJY 1" B

906001 1 ea. $248.00

80 N **CPLG HALF L110

LVJY 1 3/8" B

906004 1 ea. $134.50

80 N **CPLG HALF C5016

1 3/8" B BRWNG

906828 1 ea. $255.00

80 N **CPLG HALF C5016

1 1/4" B BRWNG

906827 1 ea. $492.00

80 N **CPLG CHAIN

C5016 BRWNG

906821 1 ea. $255.00

80 N **CPLG SPIDER L110

LVJY

906010 1 ea. $92.60

*Government-loaned property, which shall be returned to the vessel upon completion of the availability.

**New or refurbished equipment that the Government may provide for installation in place of existing equipment.

***Government-furnished property, which is to be supplied by either the vessel or the C4IT ServiceCenter xx (Rev-0)

CONSOLIDATED LIST OF CRITICAL INSPECTION ITEMS

The following is a list of work items, which contain Critical Inspection reports, which the Contractor must complete within the first 25% of the availability contract period (see SFLC Std Spec 0000, paragraph 3.2.6.5

(Inspection report particulars)):

Work

Item Title

3 Hull Plating, U/W Body, Ultrasonic Testing

4 U/W Body, Preserve, 100 percent

10 Appendages, U/W, Leak Test

17 Z-Drive Propulsion Unit, Renew, Drydock

26 Sea Strainers, Duplex, All Sizes, Overhaul

27 Sea Bay, Clean and Inspect

32 Anchor Chains and Ground Tackle, Inspect and Repair

37 Drydock

42 Crane Winch DCV, Replace

44 Pump Room, Deck, Partial Preserve

45 Vents, Preserve and Closures, Renew

48 Vent Space (01-50-0-Q), Deck, Preserve

50 Doppler Speed Log, Upgrade

51 Directional Control Valve, Upgrade

52 Sea Strainers, Simplex, All Sizes, Clean and Inspect

61 Hydraulically Operated Cargo Hatch, Inspect and Service

62 Hydraulic Chain Stoppers, Inspect And Service

63 Hydraulic Crossdeck Winches, Inspect And Service

64 Hydraulic Inhaul Winch, Inspect And Service

65 Mechanical Chain Stoppers, Inspect and Service

66 Anchor Windlass, Inspect And Service xxi (Rev-0)

68 Warping Capstan (Aft), Inspect and Service

69 Single Point Davit, Disassemble and Inspect

70 Buoy Crane, Inspect And Service

75 Vent Duct Systems, Repair

77 Drainage Valve and Remote Valve Operator, Renew

78 MDE & SSDG Exhaust Stack Insulation, Renew

81 Bilges, Preserve xxii (Rev-0)

PRINCIPAL CHARACTERISTICS - TENDER

175' WLM, BUOY TENDER

PHYSICAL

Length overall 174' 8"

Length between perpendiculars 155' 1"

Depth 14' 8"

Maximum beam 36' 0"

Designed draft 8' 0"

Mast height (above 8' waterline) 58' 8"

Frame spacing 20"

Full load displacement 855.15 Long Tons SW

Light load displacement 719.78 Long Tons SW

Minimum op condition displ 852.19 Long Tons SW

HULL

Hull material Steel

MACHINERY

Main propulsion Two Caterpillar 3508 DITA V-8 diesel; 999 BHP ea @ 1500 RPM

Two Ulstein 360 degree steerable Z-Drives, 403 SRPM @ 1600 ERPM

Reduction gears Two Z-Drive units, Cardan shafting; 3.973:1 gear ratio

Shaft seal John Crane Type ND

Shaft bearings Five pedestal mounted, Cooper split roller bearings

Number of propellers 2

Number of blades 4

Diameter 57.1"

Rudders None; Z-drive

Ship's service generators Three Caterpillar Model 3406 DITA Turbocharged; 285KW, 450V, 60 Hz, 1800

RPM

Emergency diesel generator One Caterpillar Model 3406 DIT 210 KW, 24V, 60 Hz, 1800 RPM

TANK CAPACITIES

Diesel oil capacity (100%) 16,385 gal

Fresh water capacity (100%) 7,339 gal

Lubricating oil (100%) 86 gal

1 (Rev-0)

00000_0522_FLT

REC_00000_FLT_Commercial Project @ Contractor’ Facility (0121)

General Requirements

1. SCOPE

1.1 Intent. This standard specification invokes general requirements for conducting vessel repairs performed at a commercial contractor’s facility for Coast Guard vessels.

1.2 Term interchangeability. The terms 'Contractor', 'CG Yard', 'NAVSTA EVERETT', 'shipyard', 'Base', and

'Coast Guard Industrial' are used interchangeably in this specification. Where the primary service provider is

Coast Guard personnel, references to contractor and other noted descriptors within this specification or within drawings, publications, SFLC Standard Specifications or other commercial and military references are deemed the same as prime service provider.

2. REFERENCES

COAST GUARD DRAWINGS

None

COAST GUARD PUBLICATIONS

Coast Guard Commandant Instruction (COMDTINST) M10360.3 (series), Coatings and Color Manual

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2022, General

Requirements

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2022, Welding and

Allied Processes

Surface Forces Logistics Center Standard Specification 5550 (SFLC Std Spec 5550), Latest Version, Fire Prevention and Response

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2022, Requirements for Preservation of Ship Structures

OTHER REFERENCES

Code of Federal Regulations (CFR) Title 29, Part 1915, Occupational Safety and Health Standards for

Shipyard Employment

NAVSEA Technical Publication T9074-AD-GIB-010/1688, (TP 1688), July 2012, Requirements for

Fabrication, Welding, and Inspection of Submarine Structure

2 (Rev-0)

3. REQUIREMENTS

3.1 General. The Contractor must conform to all requirements specified in SFLC Std Spec 0000 and in this item, as applicable, during the performance of this availability. The requirements of this WI applies to all work under the scope of this contract, whether explicitly stated in all following work items or not, and to all other work subsequently authorized by changes, modifications, or extensions to the contract.

3.1.1 The Contractor must conform to all requirements specified in SFLC Std Spec 5550 and in the Fire

Protection and Response work item, as applicable, during the performance of this availability.

3.1.1.1 Fire Safety Plan submission. The Contractor must submit a copy of the CFR 1915, Subpart P, Fire Safety

Plan with the Contractor’s bid when work will be conducted in a Contractor–owned facility. Include any MOA(s) with local firefighting facilities.

3.1.1.2 Fire Plan submission. The Contractor must submit a copy of the developed availability specific fire plan as requested in the Fire Protection and Response work item, with the Contractor’s bid.

NOTE

NAVSEA drawings listed will be available FOR INSPECTION ONLY from the Coast

Guard Port Engineer post-award. SFLC will not redistribute NAVSEA documents.

Contractors can apply to NAVSEA headquarters directly for copies.

3.2 Fire watch requirements. The Contractor must refer to 3.3.1.3 (Fire watch requirements) of SFLC Std Spec

0000, in accomplishing the following task:

• Provide portable fire extinguishers for Coast Guard fire watch personnel. Coast Guard fire watch is in lieu of contractor personnel during the hours of 0800-1600, Monday through Friday, and limited to two Coast Guard fire watch personnel.

• Provide fire watch personnel and fire extinguishers for the duration of the availability period, during and beyond noted Coast Guard fire watch support.

3.3 Preservation requirements. The Contractor must accomplish all preservation tasks, including touch-ups, in accordance with SFLC Std Spec 6310.

3.3.1 Brand name approval. Ensure that all contractor-furnished coatings are in accordance with SFLC Std…