Attachment 10 - Technical Exhibits.pdf

70Z08426RDL950001 TECHNICAL EXHIBIT LISTING

FOR

TRACEN CAPE MAY

HOUSING MAINTENANCE SERVICES

Ref. No. TE Number Title

1 TE-1.1 USCG Housing Layout

2 TE-1.2 Change of Occupancy Maintenance (COM) Check List

3 TE-1.3 COM Painting

4 TE-1.4 Cleaning of COM Units

5 TE-1.5 Self-Help Materials & Equipment List

6 TE-1.6 Preventative Maintenance Requirements & Annual Inspection Checklist

7 TE-1.7 Projected Workload

8 TE-1.8 Contractor Personnel Requirements

9 TE-1.9 Contract Deliverables

10 TE-1.10 Government Furnished Property & Equipment

11 TE-1.11 Government Furnished Property and Services

12 TE-1.12 CLIN Specific Standard

U.S.C.G.HOUSING CAPE MAY, NEW JERSEY

G E N E R A L

L A Y O U T

TECHNICAL EXHIBIT TE-1.2

CHANGE OF OCCUPANCY MAINTENANCE (COM) CHECK LIST

Change of occupancy work is not limited to the tasks listed below. Nor shall all tasks listed have to be performed during the COM process. Work plans for each COM will be approved by the COR. Each COM must be cleaned in accordance with TE 1.4.

Entrance Foyer/ Hallway 1.Inspect/ re-adjust entrance screen doors.

2.Open/close all windows to ensure proper operation.

3.Clean/ door mechanisms/retighten hinge screws.

4.Replace burned out/ painted over light bulbs.

LIVING/ DINING ROOM

1.Inspect/ re-adjust screen doors.

2.Open/close all windows to ensure proper operation.

3. Clean heating units/vents and ducts.

4.Clean/ door mechanisms/retighten hinge screws.

5.Inspect gas monitor/smoke detector check install dates.

6.Replace burned out/ painted over light bulbs.

KITCHEN

1. Open/close all windows to ensure proper operation.

2. Clean heating units/vents and ducts

3. Clean/ door mechanisms/retighten hinge screws.

4. Inspect fire extinguisher and tag

5. Tighten all hardware on cabinets.

6. Replace stove exhaust vent filter/Stove drip pans.

7. Operate faucet/sprayer and replace washers

8. Run dish washer/ inspect for leaks.

9. Inspect drains for leakage/repair if needed.

10. Replace burned out/ painted over light bulbs.

11. Check stove top and bottom operation.

UTILITY CLOSET/ROOM

1. Clean heating units/vents

2. Clean/ door mechanisms/retighten hinge screws.

3. Cycle washer valves.

4. Inspect external overflow pumps.

5. Drain two (2) gallons of water from water heater.

6. Replace burned out/ painted over light bulbs.

7. Inspect dryer vent for debris.

8. Inspect electrical panel for damaged breakers.

9. Replace furnace filter and return air filter (6)

BATHROOM/ LOWER

1. Clean heating units/vents.

2. Clean/ door mechanisms/retighten hinge screws.

3. Run faucet valves and drain pop-ups

4. Inspect drains for leakage/repair if needed.

5. Tighten all hardware on cabinets.

6. Tighten toilet paper/cup/toothbrush holder, towel bar(s).

7. Clean & inspect exhaust vents.

8. Replace burned out/ painted over light bulbs.

9. Flush toilet, check flapper, fill vale and handle.

10. Replace toilet seat.

STAIRWELL

1. Replace burned out/ painted over light bulbs.

2. Tighten all banister hardware.

UPSTAIRS HALLWAY

2. Clean/ door mechanisms/retighten hinge screws.

3. Inspect gas monitor/smoke detector.

4. Replace burned out/ painted over light bulbs.

UPPER BATHROOM

2. Clean/ door mechanisms/retighten hinge screws.

3. Run faucet and check sink drain pop-up

4. Inspect drains for leakage/repair if needed.

5. Tighten all hardware on cabinets.

6. Tighten toilet paper/cup/toothbrush holder, towel bar(s).

7. Clean & inspect exhaust vents.

8. Replace burned out/ painted over light bulbs.

9. Flush toilet, check flapper, fill vale and handle

10. Replace toilet seat.

BEDROOM, MASTER

1. Open/Close all windows to ensure proper operation.

2. Clean heating units/vents.

3. Clean/ door mechanisms/retighten hinge screws.

4. Inspect gas monitor/smoke detector.

5. Replace burned out/ painted over light bulbs.

BEDROOM #2

2. Clean heating units/vents.

3. Clean/ door mechanisms/retighten hinge screws.

BEDROOM #3

2. Clean heating units/vents.

3. Clean/ door mechanisms/retighten hinge screws.

BEDROOM #4

2. Clean heating units/vents.

3. Clean/ door mechanisms/retighten hinge screws.

EXTERIOR

1. Inspect/repair damage to sheds, fences, gates and latches

2. Inspect/re-screen slider screen doors

3. Clean exterior dryer vents & replace missing rodent/bird covers

4. Check/replace bulbs in exterior light fixtures

TECHNICAL EXHIBIT TE-1.3

CHANGE OF OCCUPANCY MAINTENANCE (COM) PAINTING

PART 1- GENERAL

1.1 DESCRIPTION

1.1.1 Work included but not limited to: Preparation and painting of designated family housing unit’s interior exposed surfaces as listed on the Painting Schedule in Part 3.4 of this Section, as specified herein, and as needed for a complete and proper installation. All paint products shall comply with current Federal and Regional Volatile Organic Content (VOC) and the New Jersey V.O.S. requirements and regulations. Products listed below are just examples, any COR approved equivalent is acceptable.

1.1.2 Related work:

1.1.2.1 Patching, repair and priming of damaged or new replacement surfaces shall be required prior to painting, these surfaces shall receive a coat of Prime Fast (037- 1385) applied in accordance with the manufacturer’s instructions.

1.1.2.2 Unless otherwise noted, all surfaces that are to be painted shall receive a minimum of two coats.

1.1.2.3 All interior room walls and ceilings shall be painted with Fresh Kote Latex Flat (402-128) except as noted.

1.1.2.4 All bathrooms and kitchens walls shall be painted using Fresh Kote Latex

Satin Eggshell Enamel (405-128).

1.1.2.5 All surfaces that have a natural finish wood finish (doors, railings, stairs etc.)

shall not be painted; surfaces shall be prepared and receive a polyurethane finish. During adjacent painting, these items shall be either removed or protected.

1.1.2.6 All previously painted wood trim and interior wood windows and doors shall be painted using Fresh Kote Latex Satin Eggshell Enamel (405-128).

1.1.2.7 Electric heater elements located in Phase I Housing Units shall have the metal covers painted using Rust-O-Lastic (074-128).

1.1.2.8 All exterior doors including French doors shall have only the interior surfaces painted using Rust-O-Lastic (074-128).

1.1.2.9 Walls that are to receive an satin eggshell enamel finish and do not have a physical break in the wall surface between rooms, shall have this finish continued into the adjacent room wall to the next defined edge or break.

1.1.3 Work not included:

1.1.3.1 Unless otherwise indicated, painting is not required on surfaces in concealed or inaccessible areas.

1.1.3.2 Floors and stairs (treads & risers) shall not to be painted. Stairs shall be finished as described in 1.1.2.5.

1.1.3.3 Kitchen and bathroom cabinetry shall not be painted.

1.1.3.4 Metal surfaces of anodized aluminum, stainless steel, chromium plate, copper, bronze, and similar finished materials will not require painting under this Section.

1.1.3.5 Do not paint porcelain, vinyl, laminates, baked enameled metal or prefinished surfaces unless otherwise indicated.

1.1.4 Definitions:

1.1.4.1 "Paint," as used herein, means tinted or clear coating systems materials including primers, emulsions, epoxy, enamels, sealers, fillers and other applied materials whether used as primer, intermediate, or finish coats.

1.2 QUALITY ASSURANCE

1.2.1 Use adequate numbers of skilled workmen who are thoroughly trained and experienced in the necessary crafts and who are completely familiar with the specified requirements and the methods needed for proper performance of the work of this Section.

1.3 SUBMITTALS: The following informational data shall be submitted for approval prior to the start of any work:

1.3.1 Patching Material MANUFACTURER'S DATA

1.3.2 Primer MANUFACTURER'S DATA

1.3.3 Paints MANUFACTURER'S DATA

1.3.4 Polyurethane MANUFACTURER'S DATA

1.4 EXTRA STOCK

1.4.1 Upon completion of the work of this Section, deliver to the Coast Guard an extra stock equaling 10 per cent of each color, type, and gloss of paint used in this contract, tightly sealing each container, and clearly labeling with contents and location where used.

PART 2 - PRODUCTS

2.1 PAINT MATERIALS

2.1.1 Acceptable materials:

2.1.1.1 The referenced paint products and the Painting Schedule in Part 3.4 of this

Section are based, in general, on products of M. A. Bruder & Son, Inc.

These products are referenced only to provide an approved equal manufacturer standard. Equal products of other paint manufacturers may be substituted for approval.

2.1.1.2 The color of all paint shall be M.A.B. BONE WHITE (128).

2.1.1.3 All approved painting materials and products shall be of the same manufacturer.

2.1.1.4 Use only thinners, additives etc. as recommended by the paint manufacturer, and use only to the recommended limits.

2.1.1.5 Insofar as practicable, use primers, finish coats, and necessary thinner material as part of a unified system of paint finish.

2.2 APPLICATION EQUIPMENT

2.2.1 For application of the approved paint, use only such equipment as is recommended for application of the paint by the manufacturer of the paint, and as approved by the COR.

2.2.2 Prior to use of application equipment, verify that the proposed equipment is compatible with the material to be applied, and that integrity of the finish will not be jeopardized by use of the proposed equipment.

2.3 OTHER MATERIALS

2.3.1 Provide other materials, not specifically described but required for a complete and proper installation.

PART 3 - EXECUTION

3.1 MATERIALS PREPARATION

3.1.1 General:

3.1.1.1 Mix and prepare paint materials in strict accordance with the approved manufacturers' recommendations.

3.1.1.2 All acrylic base paints shall have a fungicide M1 Mildew Additive (101- 4153) added and mixed with the paint in accordance with the manufacturer’s instructions prior to application of the paint.

3.1.1.3 When materials are not in use, store in tightly covered containers

3.1.1.4 Maintain containers used in storage, mixing and application of paint in a clean condition, free from foreign materials and residue.

3.2 SURFACE PREPARATION

3.2.1 General:

3.2.1.1 Perform preparation and cleaning procedures in strict accordance with the approved paint manufacturers' recommendations.

3.2.1.2 Surfaces that have been patched or new materials have been install shall be sanded smooth and level, cleaned of all dust and then primed with Prime Fast (037-1385) applied in accordance with the approved manufacturer’s instructions.

3.2.1.3 Surface preparation shall be accomplished by thoroughly cleaning and removing all dirt, grease, and oil, powdering plaster, glue size or paste and other surface contaminants that might impair adhesion. Sand hard or glossy surfaces. Remove loose, peeling paint and sand edges smooth.

Remove all sanding dust using a treated or damp cloth. Spackle nail holes and cracks, sand smooth and touch-up before applying finish coat.

Avoid abrading drywall face paper. Remove rust and/or scale from metal surfaces that are to be painted. Seal water soluble stains, knots and sap streaks with Lok-Tite Stain Sealer (037-159).

3.2.1.4 Remove removable items, which are in place and are not scheduled to receive paint finish; or provide surface-applied protection prior to surface preparation and painting operation. These shall consist of but not be limited to, switch plates, receptacle plates, electric panels, access doors, lighting fixtures, grilles, registers, door stops, handles, vent louvers, etc.

3.2.1.5 Following completion of painting in each space or area, reinstall the removed items by using workmen who are skilled in the necessary trades to accomplish this task.

3.2.1.6 Schedule the cleaning and painting so that dust and other contaminants from the cleaning process will not fall onto wet newly painted surfaces.

3.3 PAINT APPLICATION

3.3.1 General:

3.3.1.1 Each coat of paint shall be applied in strict accordance with the approved paint manufacturer’s instructions. Each coat of paint shall have a minimum 2 mil DFT.

3.3.1.2 Make sure each coat has sufficiently dried before applying succeeding coats.

3.3.1.3 Sand and remove dust between coats to remove defects visible to the unaided eye from distance of five feet.

3.3.2 Application:

3.3.2.1 When brush application is used to apply paint, care shall be taken to work each brush stroke onto the surface in a uniform manor, applying the film evenly.

3.3.2.2 When roller application is used to apply paint, roller strokes shall be applied using zigzag pattern to hide any roller patterns and distribute the paint evenly.

3.3.2.3 When spray application is used to apply paint, apply each coat to provide the hiding equivalent of brush coats. Do not double back with spray equipment to build up film thickness of two coats in one pass.

3.3.2.4 Cloudiness, spotting, holidays, laps, brush marks, runs, sags, ropiness, and other surface imperfections will not be acceptable.

3.4 PAINTING SCHEDULE: Provide the following finishes.

3.4.1 Interior metal, ferrous:

3.4.1.1 First coat: Rust-O-Lastic (074-128)

3.4.1.2 Second coat: Rust-O-Lastic (074-128)

3.4.2 Interior walls and ceilings paint: (Note these paints shall include a fungicide additive)

3.4.2.1 Used on gypsum drywall (all ceilings and walls except kitchen and bathrooms walls):

3.4.2.1.1 Primer (if required): Prim Fast (037-1385)

3.4.2.1.2 First coat: Fresh Kote Latex Flat (402-128)

3.4.2.1.3 Second coat: Fresh Kote Latex Flat (402-128)

3.4.2.2 Used on wood trim and gypsum drywall (all kitchen and bathroom walls):

3.4.2.2.1 Primer (if required): Prim Fast (037-1385)

3.4.2.2.2 First coat: Fresh Kote Latex Satin Eggshell Enamel (405-

128)

3.4.2.2.3 Second coat: Fresh Kote Latex Satin Eggshell Enamel (405-

128)

3.4.3 Natural Wood Finish:

3.4.3.1 First coat: Rich Lux Gloss Polyurethane Wood Finish (086-899)

3.4.3.2 Second coat: Rich Lux Gloss Polyurethane Wood Finish (086-899)

3.5 FINAL CLEAN UP

3.5.1 Upon the completion of all required painting, the Contractor shall remove all debris, dust, paint spots or splattering, etc., resulting from this contract. All surfaces’ areas shall be left clean and in the same condition as prior to this contract.

TECHNICAL EXHIBIT TE-1.4

CLEANING OF COM UNITS

1.1 SCOPE OF WORK

The Contractor shall provide all supervision, labor, tools, materials, transportation, equipment, and services as required cleaning vacant government housing units prior to the assignment of houses to new residents.

1.2 CONDITIONS OF WORK/PERFORMANCE REQUIREMENTS

The condition and level of cleanliness in the housing units to be cleaned will vary from unit to unit depending upon the amount of maintenance work done on the unit after the previous tenant vacated and cleaned their unit. The purpose of the work, required under this contract, is to thoroughly clean the entire house after maintenance work has been completed in order that the new residents move into a functional and attractively clean unit. The contractor is required to perform the following cleaning tasks in each housing unit assigned for cleaning:

a. Clean kitchen floor of all dirt, debris, dust, scuff marks, heel marks, other stains and discoloration or other foreign matter.

b. Clean kitchen counter.

c. Clean interior and exterior of kitchen cabinets. Wipes clean all dirt, debris, dust, other stains and discoloration, and other foreign mater.

d. Clean and polish kitchen sink making sure sink is free of any rust stains.

e. Clean interior and exterior of stove. Clean under the stovetop for those units that open.

Wipes clean all dirt debris, dust, other stains and discoloration, and other foreign matter.

f. Clean stove exhaust fan and cover

g. Clean interior and exterior of oven. Wipes clean all dirt debris, dust, other stains and discoloration, and other foreign matter.

h. Clean interior and exterior of refrigerator. Wipes clean all dirt, debris, dust, other stains and discoloration, and other foreign matter.

i. Clean interior and exterior of dishwasher.

j. Clean and polish all bathroom fixtures (Medicine cabinets, mirrors, sinks, bathtubs, toilets and toilet bowls)

k. Clean, strip and wax all tiled floors. Clean and mop all no-wax linoleum floors using soap and water. Wipes clean all dirt, debris, dust, scuff marks, heel marks, other stains and discoloration and other foreign matter. Floors shall have a uniform appearance without streaks, swirl marks, or any evidence of soil, stain, and film or standing water.

l. Dust out all heating/cooling vents. (Includes both heating registers and Whole House Ceiling fans)

m. Dust all horizontal planar surfaces (cabinets, shelves, windowpanes and sills, top of doors, light fixtures, molding, tops of furnace and hot water heaters).

n. Clean the interior and exterior of all windows and sills. After cleaning, there shall be no traces of film, dirt, smudges, water, or other foreign matter. Wash all screens, clearing them of any dust and dirt.

o. Clean all lighting fixture covers inside and out. After cleaning, there shall be no traces of film, dirt, smudges, water, or other foreign matter.

p. Clean stairways. Clean wood stairways using oil soap. Vacuum all carpeted stairwells.

q. Clean interior walls and doors. For any walls that have not been painted, wash walls to remove smudging, handprints or soiled areas and any dust.

r. Remove and dispose of any trash or debris that may have accumulated in the house.

s. Vacuum and steam clean carpeted areas. After cleaning, the carpeted area shall be free of all visible dirt, debris, litter and other foreign matter. Any spots shall be removed by carpet manufacturer’s approved methods as soon as noticed. All tears, burns and raveling shall be brought to the attention of the government representative.

t. Sweep and clean all exterior storage areas.

u. Sweep, clean and wash patio areas.

TECHNICAL EXHIBIT TE-1.5

TRACEN CAPE MAY SELF HELP MATERIALS & EQUIPMENT LIST

General Consumable Supplies available for resident check-out and use:

• Paint, interior, flat wall & ceiling.

• Paint, interior, eggshell, doors and wooden trim work.

• Paint, touch-up, white for appliances.

• Caulk, interior/exterior latex and silicone depending upon specific application.

• Drywall material for small repairs, all types, standard, mold resistant etc.

• Drywall joint compound, limited quantities matched to specific repair.

• Glue, carpenters.

• Sandpaper 40 – 120 grit various grades.

• Wood Putty/Plastic wood quantities gauged to specific project.

• Porcelain compound, white, suitable for sink & bathtub touch ups.

• HVAC filters, HEPA type.

• Weather stripping all types as required by specific application.

• Vinyl cove base material.

• Vinyl adhesive compound.

Specific Area or Component-related Items:

Door Related Items:

• Bi-fold closet doors.

• Interior doors flat slab or six panel.

• Door passage locksets.

• Assorted door hardware including storm door.

• Storm door closure.

• Storm door handles & screens.

• Touch up paint (all door types).

First Floor related items:

• Door passage locksets & hardware.

• Bi-Fold door related hardware & knobs.

• Closet shelving & clothes poles must specify length.

• Door Stops and related plates.

• CO detector (must turn in malfunctioning unit).

• Smoke detector (must turn in malfunctioning unit).

• Energy efficient bulbs as applicable (must turn in old bulb).

• Mini-Blinds (must turn in blind requiring replacement).

• Ceiling fan parts (as required to facilitate minor repairs).

• HVAC replacement diffusers, floor or ceiling type.

Kitchen:

• Refrigerator parts (as required to facilitate minor repairs, i.e., handles, shelves, rack supports, light bulbs etc.)

• Stove/Range parts (as required to facilitate minor repairs, i.e., handles/knobs, shelves, drip pans, racks, light bulbs etc.)

• Range back splash sections.

• Range interior light bulbs.

• Range hood filters, light bulbs and light covers.

• Ceiling light bulbs, fixture type specific.

• Sink faucet drain baskets.

• Sink faucet aerators.

• “Drano” type “safe for piping” drain cleaning compounds.

• Cabinet pulls, specific to cabinet type.

• Cabinet parts misc. sufficient to complete minor repairs.

• HVAC replacement diffusers, floor or ceiling type.

Exterior related items:

• Repair components for wooden fences, misc. fence boards, copper caps, latches all fence-related hardware etc.

• Exterior light fixtures, Coach & Jelly Jar type, must be qualified to install COR discretion.

• Grass Seed.

• Patio Block (limited quantities, COR discretion.)

• Landscaping timber (limited quantities, COR discretion.)

• Brick molding to be used to repair around doors, (quantities issued limited to specific task).

• Exterior walls & door touch up paint, (quantities issued limited to specific task).

• Topsoil, (limited quantities, COR discretion.)

• Flag Pole holder.

• Pest Control supplies (over the counter type) (limited quantities, COR discretion.)

• Yard Maintenance Equipment on SIGN OUT BASIS as available, lawn mowers, weed whackers, pruning shears, leaf blowers, edger’s, etc.

Bathrooms:

• Misc. bath fixtures to include towel bars, toilet seats, toilet handles, sink fixtures, soap dishes, toothbrush holders, light fixtures (COR discretion), light bulbs, toilet paper roll holders, etc.

• Doors and door related hardware (all).

• Shower curtain rods and associated hardware.

• Light fixture bulbs, switch & outlet cover plates.

• Medicine cabinet parts, doors, handles, light covers etc.

• HVAC replacement diffusers, floor or ceiling type.

Stairwell & Hallways:

• Stairwell anti-slip threads.

• Doors & door related hardware.

• Electrical outlets cover plates.

• Bannister/handrail parts.

• Poly for stairs.

• Light bulbs for recessed light fixtures.

• Light bulbs and parts for Pendant Style Lights.

• Carbon Monoxide detectors (must turn in malfunctioning unit).

• Smoke detectors (must turn in malfunctioning unit).

Bedrooms:

• Door passage locksets & hardware.

• Bi-Fold door related to hardware & knobs.

• Closet shelving & clothes poles must specify length.

• Door Stops and related plates.

• Carbon Monoxide detector (must turn in malfunctioning unit).

• Energy efficient bulbs as applicable (must turn in old bulb).

• Mini-Blinds (must turn in blind requiring replacement).

• Ceiling fan parts (as required to facilitate minor repairs).

• HVAC replacement diffusers, floor or ceiling type.

SELF-HELP TOOLS (SIGN OUT/LOAN OUT BASIS):

• Misc. hand tools such as battery-operated drill sets with chargers, battery operated Sawzall sets with chargers, saw, drill/driver guns, drill bits, caulking guns, screwdrivers, wrench sets, socket wrench sets, pliers, paint application equipment, rollers trays, brushes, etc. 6’ and 8’ step ladders.

• Hand tools for yard maintenance work, heavy duty shovels, rakes, hoes, wheelbarrows, etc.

• Lawn mower.

• Weed Whackers.

• Edgers.

• Pruners.

• Leaf Blowers.

• Snow shovels.

• Ice Melt Compound.

• Rug Doctor carpet cleaners

• Power Washers.

• Power Circular Saw.

• Power drills (corded) up to ½” size.

• Assorted Drill-bits (indexed).

****All self-help equipment and supplies will be signed out to the resident by the service provider and will be required to be returned to the self-help store the next self-help day except for consumable supplies.****

TECHNICAL EXHIBIT TE-1.6

PREVENTATIVE MAINTENANCE REQUIREMENTS & ANNUAL INSPECTION

CHECKLIST

Contractor shall annually confirm/update the below information:

TECHNICAL EXHIBIT TE-1.7

PROJECTED WORKLOAD

PROJECTED WORKLOAD

Change of Occupancy Maintenance (COMS) Totals

Workload for Bid Purposes 80

Re-negotiation Threshold +/- 15%

Service Calls (Work Orders) Totals

Workload for Bid Purposes 1,200

Re-negotiation Threshold +/- 15%

Annual Inspections 174

HOUSING INVENTORY

Phase Type Square Feet Heat Source Other Quantity

I-Enlisted 3BR 1 238 Natural Gas Central A/C 48Furnace

I-JO 3BR 1,426 Natural Gas Central A/C 8 Furnace

I-Enlisted 4BR 1,432 Natural Gas Central A/C 12 Furnace

I-JO 4BR 1,630 Natural Gas Central A/C 2 Furnace

Quarters “A” 4BR 2,819 Natural Gas

Central A/C 1 Boiler System—2-

C Garage Detached

I-Single Family 3BR Approx 1,400 Natural Gas Central A/C 3

I-Single Family 4BR Approx 1,600 Natural Gas

Central A/C 1

II & III 3BR 1,464 Natural Gas Furnace

Central A/C Includes Whole

House Fan

II & III 4BR 1,707 Natural Gas Furnace

Central A/C Includes Whole

House Fan

IV 2BR 1,251 Natural Gas Furnace

Central A/C Includes Whole

House Fan

PROJECTED WORKLOAD

Quarters “B” 4BR Approx 1,800 Electric &

Central A/C 1 Gas Furnace & 2 Car Garage

Propane Gas i

Attached Place

OTHER STRUCTURES

Other Structure Location Quantity Comments

Basketball Court Prior to Base Main

Entrance (SE side of Pennsylvania Ave)

Asphalt Surface with

(2) fixed basketball hoops

Bus Stop Shelters Various on Penn. Ave 7 Metal Framed Glass/Lexon

Playgrounds Various throughout 6 Housing

Building 290 1521 Delaware Avenue 1 Building Manager Cape May, NJ 08204

Detached Storage Phase I, II, and III 34 Multi-unit Sheds

Fences Each Unit, 1400 Perimeter of each housing Playgrounds unit back yard

Phase IV storage areas are attached sheds

Current type: 1X6 Cedar “Good Neighbor” F

Play structures, swings, rubber mulch, etc.

TECHNICAL EXHIBIT TE-1.8

CONTRACTOR PERSONNEL REQUIREMENTS

PROJECT MANAGEMENT: The Contractor shall be responsible for managing the total work effort associated with the operation, maintenance, management, quality control, and other services required herein to ensure fully adequate and timely completion of these services.

Included in this function shall be a full range of management duties including, but not limited to, overall project management, planning, scheduling, cost accounting, report preparation, supervising, establishing and maintaining records and inventories, warranty administration, administering and performing a preventative maintenance program, quality control, and all related work. The Contractor shall maintain adequate personnel with the necessary management and supervisory expertise on staff to ensure the contract work performance requirements.

Included in management are the following:

(a) The Contractor is encouraged to establish a project management program which is innovative and uses full advantage the facilities provided by the Government. Proposed changes to, or deviations from the contract must offer an equivalent program/service, or other consideration and must be submitted in writing to the Contracting Officer and COR for approval.

(b) Changes in supervision shall be furnished to the Contracting Officer and the COR in writing email at a minimum, 48 hours prior to making such changes. The Project Manager shall be given the authority by the Contractor to maintain sufficient working personnel to accomplish all phases of the work in a satisfactory and acceptable manner. In addition to supervision, the following functions are also included in Project Management:

• Schedules

• Records and Reports

• Estimates

• Warranty Program

• Self-Help Operation

• As-Built Plans

(c) The Contractor or his representative shall meet with the Contracting Officer or his/her representative weekly during the first two months of the contract. Meetings will be as often as necessary at the discretion of the Contracting Officer but not less than monthly thereafter.

The Contractor’s representative and the Government’s representative shall sign written minutes of meetings, prepared by the Government. Should the Contractor not concur with the minutes, the Contractor shall state, in writing, to the Contracting Officer any areas of disagreement and the response will be incorporated into the minutes.

Supervision: The Contractor shall have a Project Manager who has earned a Project Management certification, or a minimum of two (2) years of current experience in managing facility maintenance contracts/projects of similar size and complexity; OR a minimum of five (5) years of experience in managing facility maintenance contracts/projects of similar size and complexity.

The Project Manager shall have the authority to act upon the Contractor’s behalf. At a minimum, the Contractor's representative shall be on station during normal working hours and shall be physically available to the Contracting Officer or his representative within 15 minutes of notification. Instruction given by the Contracting Officer or his representative to the Contractor's Project Manager shall be considered to have been given directly to the Contractor.

Contractor Work Response: The Contractor shall implement all necessary work response procedures to ensure timely accomplishment of work requirements of this contract as outlined in Section 1.

Supervisory Tasks: Qualified supervision shall be available at all times, day or night, whenever work is being performed under this contract, to ensure performance and accomplishment of the work in strict accordance with this specification. At a minimum, the Contractor shall insure the following:

(a) The Contractor shall furnish a sufficient number of competent and qualified personnel to accomplish the services identified in this contract. Record of current certifications must be retained at the Contractor's on site office, and shall be made available to the Contracting Officer upon request.

(b) The Contractor shall comply with all federal, state, and local laws regarding licenses, certifications, training, etc., of employees performing the specified services.

(c) The Contractor shall train personnel properly in performance of work in accordance with tasks and methods outlined herein.

(d) The Contractor shall prevent general carelessness in operations and abuse of facilities, and shall instruct employees to abide by safety rules and regulations for protection of tenants, visitors and themselves.

Other Contractors: During the course of this contract, other Contractors may be engaged in similar and supporting work requiring close cooperation. The Contractor shall cooperate in scheduling work with other contractors to avoid conflict or disruption of other work.

Subcontractors: During the course of this contract, the Contractor may subcontract out work and services. This does not relieve the Contractor of the ultimate responsibility to meet the requirements of this contract. The Contractor shall be held accountable for the performance of any services and work accomplished by his subcontractors. The Contractor is required to perform at a minimum 60% of the requirements of this contract with prime Contractor’s workforce. Maintenance Management shall not be subcontracted.

Safety: The Contractor shall ensure that work performed under this contract is conducted in strict regard for safety of workers and others who might be affected by the work. The Contractor shall be responsible for compliance with all applicable federal, state, and local laws as well as all applicable standards and regulations established by the Occupational Safety and Health

Administration (OSHA). Compliance with the most stringent regulation applicable to the work from the above guidelines shall be the sole responsibility of the Contractor. The Contractor shall be responsible for establishing and implementing a safety program, approved by the Contracting Officer, which will provide a safe work environment.

Conduct of Employees: The Contractor shall provide employees who shall conduct themselves in a proper, responsible and businesslike manner, which at a minimum includes the following:

(a) Contractor personnel shall participate in any safety drills (fire drills, civil defense exercises) as required.

(b) Contractor personnel shall report fires, hazardous conditions, damage to buildings and fixtures or any unauthorized occupancy.

(c) Contractor personnel shall prevent wasteful practices in connection with Government- furnished utilities.

(d) Official government telephones shall only be used by Contractor personnel for official Government business.

(e) Contractor personnel shall be dressed in appropriate clothing and shall present a clean, neat appearance at all times when performing under the contract.

Employee Qualifications: The Contractor shall provide personnel who are capable and trained in the performance of the duties to which they are assigned. This includes appropriate trade certification for the specific trade work performed by each contract employee or subcontractor (i.e., electrician, carpenter, plumber, HVAC mechanic, maintenance mechanic, masonry, etc.). At a minimum the KTR shall have an electrician, carpenter, plumber, HVAC technician, maintenance mechanic and masonry. The Contractor shall train personnel to perform all assignments in accordance with the requirements and performance standards of this contract and ensure employees possess all licenses and certifications required by for their assigned functions. All Contractor employees working with electricity shall be trained in CPR and carry an up-to-date CPR card certifying the training has been done. In addition, the Contractor shall ensure that Contractor employees meet all minimum requirements, as applicable. The Contractor shall provide a copy of all certifications and annual updates.

Equipment Operators: Contractor personnel operating automotive, construction, weight handling, material handling or miscellaneous equipment shall be properly qualified and licensed. The Contractor is responsible for ensuring personnel operating such equipment have been properly trained. Training shall be documented and available for review by the Contracting Officer. Personnel shall have any such licenses in their possession, when operating vehicles under this contract. Operators shall exercise due care while operating equipment and execute appropriate pre-operation and operational checks of equipment as required by Industry Standards.

TECHNICAL EXHIBIT TE-1.9

CONTRACT DELIVERABLES

Title PWS Reference Initial Submission Initial

Submissions

Subsequent Submissions

Key Positions/Resumes 3.2 With Proposal (Technical Approach/Technical Plan)

KO/COR Point of Contact information within 15 days of contract start date.

PM, APM, & QCM

Assigned Personnel Contact Information

3.2 NLT 15 calendar days before Performance Start Date (PSD)

KO/COR 5 working days prior to effective date of change

Meeting Minutes 4.8 Within 5 working days of meeting COR Non-concurrence with meeting minutes shall be provided in writing no more than 10 calendar days

Organization Chart 3.3.5 With Proposal (Technical Approach/Technical Plan)

KO/COR

NLT 15 calendar days before Performance Start Date (PSD) and within 5 working days of a change

List of KTR Personnel 3.3.6.1 NLT 15 calendar days before PSD KO/COR Within 5 working days of change

Conditional Access to Sensitive but Unclassified Information

3.3.6.3 NLT 15 calendar

days before PSD COR Prior to KTR start date

Management Plan 4.6.3 With Proposal (Technical Approach/Technical Plan)

KO/COR NLT 15 calendar days before PSD

Technical Plan 4.6.4 With Proposal (Technical Approach/Technical Plan)

KO/COR NLT 15 calendar days before PSD

Staffing Plan 1.7.2 With Proposal (Technical Approach/Technical Plan)

KO/COR N/A

Quality Control Plan 4.6.5 With Proposal (Technical Approach)

KO/COR

Updated Quality Control Plan NLT 15 calendar days before PSD with subsequent annual reviews and updates submitted NLT anniversary of PSD.

Any other changes within 5 days of change.

Hazardous Material and Waste Management Plan 4.6.6

With Proposal (Technical Approach)

KO/COR

Updated Hazardous Material and Waste Management Plan NLT 15 calendar days before PSD with subsequent annual reviews and updates submitted NLT anniversary of PSD. Any other changes within 5 days of change

Business Continuity Plan 4.6.7 With Proposal (Technical Approach)

KO/COR

Updated Business Continuity Plan NLT 30 calendar days after the award date with subsequent annual reviews and updates submitted NLT anniversary of PSD. Any other changes within 5 days of change

Property Control System Plan 4.6.8

With Proposal (Technical Approach)

KO/COR

Updated Property Control System Plan NLT 15 calendar days before PSD with subsequent annual reviews and updates submitted NLT anniversary of PSD. Any other changes within 5 days of change

Employee Record of Training NLT 15 calendar days before PSD

Certificate of Insurance Per FAR 52.228-5

NLT 15 calendar days before PSD KO Annually within 10 days after the anniversary of

PSD

Service Contract Report Per FAR 52.204-14

NLT 15 calendar days before PSD

KO/ System for Award Management

(SAM)

Annually, by 31st October

Non-Disclosure Agreement (DHS Form 11000-6) 4.9 NLT 15 calendar days before PSD KO/COR As needed – per employee.

DESCRIPTION BRAND SERIAL NUMBER MODEL NUMBER Location

1'' ROT HAMMER DRILL MILWAUKEE BO4A708230022 5363-21 SHOP

1'' ROT HAMMER DRILL MILWAUKEE BO3C709200641 5363-21 SHOP

6'' JAM SAW ROBERTS 1055 SHOP

6 GALLON AIR COMPRESSOR PORTERCABLE 2966643776 C2002 SHOP

6 GALLON AIR COMPRESSOR PORTERCABLE SHOP

6 GALLON AIR COMPRESSOR PORTERCABLE C2006 SHOP

10'' TABLE SAW BOSCH 401294874 TS3000 SHOP

10'' TABLE SAW BOSCH 401294895 TS3000 SHOP

10'' TABLE SAW ROCKWELL LG-7633 34-762 SHOP

10'' COMPOUND MITRE SAW DEWALT 235085 DW713 SHOP

10'' COMPOUND MITRE SAW HITACHI C215821 C10FCE2 SHOP

10'' SLIDE COMPOUND MITRE SA DEWALT SHOP

12'' PLANER DEWALT 0045CT0952 DW733 SHOP

6 1/4'' CIRCULAR SAW BOSCH 611000279 1671 SHOP

7 1/4'' CIRCULAR SAW BOSCH 706056218 CS10 SHOP

7 1/4'' CIRCULAR SAW SKILLSAW 89219 5680 SHOP

7 1/4'' CIRCULAR SAW RYOBI BB063790123 CSB121 SHOP

1/2'' COARDED DRILL RIGID CS104063732 R7111 SHOP

18V CIRCULAR SAW DEWALT 587314 DC390 SHOP

21' FRAMING GUN BOSTITCH N88RH-2MCN F21PL SHOP

16 GAGE NAILER DEWALT 31952 DC616 SHOP

16 GAGE TRIM GUN PORTERCABLE 200803BA228858 SHOP

16 GAGE TRIM GUN PORTERCABLE 200803BA228247 SHOP

16 GAGE TRIM GUN PORTERCABLE 16228305 FN250SB SHOP

AIR MOVER DRYSER LX58022 AP110004 SHOP

AIR MOVER RIDGID 1127AE00621 AM25500 SHOP

AIR MOVER RIDGID 1127AE00232 AM25500 SHOP

AIR MOVER RIDGID 12309R0114 AM25600 SHOP

AIR SANDER CAMBELL HAUSFIELD TL1005 SHOP

BAND SAW DELTA 315571 28-276 SHOP

SHOP

BENCH GRINDER DELTA W10-87 23-850 SHOP

COMPACT ROUTER DEWALT 990714 D26670 SHOP

DRILL PORTER CABLE 47784 754SEHD SHOP

DRILL PRESS DELTA 87K79034 17540 SHOP

DRILL SNAKE RIDGID 912 K-45 SHOP

DRILL SNAKE RIDGID 614 K-45 SHOP

DRILL SNAKE RIDGID K-39 SHOP

DRYER VENT BLOWER 16445 1005-1 SHOP

FOOD WASTE DISPOSER BADGER 14041847619 5-84 SHOP

FOOD WASTE DISPOSER BADGER 14041628103 5-84 SHOP

FOOD WASTE DISPOSER BADGER 14041847635 5-84 SHOP

GAS POWER HYDRO JET SPARTAN 2983 P319162EUSTB SHOP

GRINDER BLACK AND DECKER 7170830 SHOP

HAND PLANER RYOBI BB0821317376 HPL51 SHOP

HEAT GUN WANGER HT1000 SHOP

HIGH TEMP TESTER UNIVERSAL MT012A SHOP

HOT SHOT 400 GENERAL HSR0277 400 SHOP

HOT SHOT 400 GENERAL HSV0398 400 SHOP

HOT SHOT 400 GENERAL HSV0400 400 SHOP

JIG SAW DEWALT 6.1752E+11 DW327 SHOP

JIG SAW BOSCH 203005571 JS365 SHOP

ORBITAL SANDER DEWALT 2931 D26451 SHOP

OSCILLATING MULTI TOOL PORTERCABLE 4S-58 PCE605 SHOP

OSCILLATING MULTI TOOL PORTERCABLE 38-58 PCE605 SHOP

PANEL SAW SAFETY SEED MFE 5860-78 SHOP

PORTABAND PORTER CABLE 409416 725 SHOP

POWER HAMMER REMINGTON D52085 476 SHOP

POWER WASHER BLUE CLEAN 13771-52170107 AR3835 SHOP

PROFILE SANDER PORTERCABLE 485516A3001 444 SHOP

RADIAL ARM SAW DELTA 438-02-314-2067 SHOP

ROOFING GUN PORTERCABLE RN175B SHOP

ROTOZIP ROTOZIP 981009530 DR1 SHOP

ROUTER BOSCH 1601 SHOP

ROUTER PORTER CABLE 97818 890 SHOP

SANDER DELTA 87F26885 31-730F SHOP

SANDER RYOBI AJ103795197 RS290 SHOP

SAW ZAW BOSCH 706004357 RS325 SHOP

SAW ZAW BOSCH 706004345 RS325 SHOP

SAW ZAW BOSCH 706004339 RS325 SHOP

SAW ZAW DEWALT 640955 DW304P SHOP

SHOP VAC 4 GALLON RIGID 10027R0404 WD400700 SHOP

SHOP VAC 6 GALLON RIDGID 15226R2151 WD06701 SHOP

SHOP VAC 6 GALLON RIDGID 15225R2861 WD06701 SHOP

SHOP VAC 16 GALLON RIDGID 09161R0161 WD16650 SHOP

SHOP VAC 16 GALLON RIDGID 11238R3035 WD16360 SHOP

STEAM CLEANER STEAMBRIGHT J5635 SBM-60-DX-H-A SHOP

SPACE HEATER BIG HEAT 475346 6200 SHOP

SPACE HEATER BIG HEAT 998362 6200 SHOP

SUPER FREEZE RIDGID 1217233 SF-2500 SHOP

TABLE SAW PORTERCABLE 66617 PCB222TS SHOP

TILE CUTTER CRAIN 1701052A 1 SHOP

TILE CUTTER CRAIN 1701051A 1 SHOP

TILE CUTTER CRAIN 1701056A 1 SHOP

ITEM # DESCRIPTION BRAND SERIAL NUMBER MODEL NUMBER LOCATION

CARPET CLEANER RUG DOCTOR 10275208 MPC3 SELF HELP

#5 CARPET CLEANER RUG DOCTOR 10228040 MPC3 SELF HELP

#7 CARPET CLEANER RUG DOCTOR 10228224 MPC3 SELF HELP

RD #1 CARPET CLEANER RUG DOCTOR 10227652 MPC3 SELF HELP

#6 CARPET CLEANER RUG DOCTOR 10274501 MPC3 SELF HELP

#3 CARPET CLEANER RUG DOCTOR 09A46911 MPC2D SELF HELP

#1 CARPET CLEANER RUG DOCTOR 10A03053 MPC2D SELF HELP

#4 CARPET CLEANER RUG DOCTOR 20020817 MPC3A SELF HELP

RD #4 CARPET CLEANER RUG DOCTOR 20020817 MPC3A SELF HELP

#8 CARPET CLEANER RUG DOCTOR 200221458 MPC3A SELF HELP

RD #5 CARPET CLEANER RUG DOCTOR 2020755 MPC3A SELF HELP

RD #2 CARPET CLEANER RUG DOCTOR 20022150 MPC3A SELF HELP

G6 CART GORILLA CART YARD

NO # CART GORILLA CART YARD (BROKEN)

NO # CART GORILLA CART YARD (BROKEN)

#3 DRILL KIT DEWALT W04A1P3 DCD777 SELF HELP

#2 DRILL KIT DEWALT W04A1HF DCD777 SELF HELP

#1 DRILL KIT DEWALT 570033 DCD780 SELF HELP

NO # EDGER BLACK AND DECKER LE750 #12 MAIN SHED

NO # EDGER BLACK AND DECKER LE750 #12 MAIN SHED

NO # GENERATOR HONDA EB5000X #12 MAIN SHED

#3 GRASS SEED SPREADER SCOTTS DLX #12 MAIN SHED

#2 GRASS SEED SPREADER SCOTTS DLX #12 MAIN SHED

#1 GRASS SEED SPREADER SCOTTS DLX #12 MAIN SHED

NO # GRASS SEED SPREADER SCOTTS MINI #12 MAIN SHED

GW5 HEDGE TRIMMERS GREEN WORKS GWW2400250 22242 #12 MAIN SHED

GW6 HEDGE TRIMMERS GREEN WORKS GWW2400249 22242 #12 MAIN SHED

#1 IMPACT DRILL KIT DEWALT 913353 DCF885 OFFICE

#2 IMPACT DRILL KIT DEWALT W045D7V DCF787 OFFICE

#3 IMPACT DRILL KIT DEWALT W045CZ2 DCF787 OFFICE

#3 6' LADDER WERNER #11 SALT SHED

#4 6' LADDER WERNER #11 SALT SHED

#6 6' LADDER WERNER #11 SALT SHED

SJ1 LAWN MOWER SUN JOE 9.40206E+14 MJ402E #12 MAIN SHED

SJ2 LAWN MOWER SUN JOE 9.40206E+14 MJ402E #12 MAIN SHED

Y12 LAWN MOWER YARD MACHINE 1A046K12061 500E #12 MAIN SHED

HM2 LAWN MOWER HUSQVARNA 8958196 L-22-1A #12 MAIN SHED

HM3 LAWN MOWER HUSQVARNA 8794558 L-22-1A #12 MAIN SHED

HM5 LAWN MOWER HUSQVARNA 8794570 L-22-1A #12 MAIN SHED

TB7 LAWN MOWER TROYBILT 8381842 TB-130XP #12 MAIN SHED

TB10 LAWN MOWER TROYBILT 8381540 TB-130XP #12 MAIN SHED

TB8 LAWN MOWER TROYBILT 8381845 TB-130XP #12 MAIN SHED

TB9 LAWN MOWER TROYBILT 8381862 TB-130XP #12 MAIN SHED

TB6 LAWN MOWER TROYBILT 8381537 TB-130XP #12 MAIN SHED

TB3 LAWN MOWER TROYBILT 1H307K92097 TB-110 #12 MAIN SHED

TB5 LAWN MOWER TROYBILT 1H307K92538 TB-110 #12 MAIN SHED

TB2 LAWN MOWER TROYBILT 1H307K92541 TB-110 #12 MAIN SHED

NO # LAWN MOWER YARD MACHINE 1.51219E+11 500E #12 MAIN SHED (BROKEN)

NO # LAWN MOWER YARD MACHINE 1.51219E+12 500E #12 MAIN SHED (BROKEN)

NO # LAWN MOWER YARD MACHINE 1.6021E+12 500E #12 MAIN SHED (BROKEN)

NO # LAWN MOWER YARD MACHINE 1.51015E+12 500E #12 MAIN SHED (BROKEN)

NO # LAWN MOWER YARD MACHINE 1.51015E+12 500E #12 MAIN SHED (BROKEN)

NO # LAWN MOWER BOLENS 1.81115E+12 450E #12 MAIN SHED (BROKEN)

NO # LAWN MOWER POULAH PRO109055143800 500E #12 MAIN SHED (BROKEN)

NO # LEAF BLOWER (G) ECHO P40212183631 PB250LN #12 MAIN SHED

NO # LEAF BLOWER (G) RYOBI EV13236D020086 PB42 #12 MAIN SHED

NO # LEAF BLOWER (G) RYOBI EV12465D020718 PB42 #12 MAIN SHED

#1 LEAF BLOWER (G) ECHO 9018019 PB413H #12 MAIN SHED

W3 LEAF BLOWER (E) WORX 2.01415E+11 WG505 #12 MAIN SHED

W6 LEAF BLOWER (E) WORX 2.01415E+11 WG505 #12 MAIN SHED

W4 LEAF BLOWER (E) WORX 2.01413E+11 WG505.I #12 MAIN SHED

W5 LEAF BLOWER (E) WORX 2.01411E+11 WG505.I #12 MAIN SHED

W2 LEAF BLOWER (E) WORX 2.01411E+11 WG505.I #12 MAIN SHED

W1 LEAF BLOWER (E) WORX 2.01411E+11 WG505.I #12 MAIN SHED

GW4 LEAF BLOWER (E) GREEN WORKS PRO GWW0630631 BLG0L00 #12 MAIN SHED

GW3 LEAF BLOWER (E) GREEN WORKS PRO GWW0630642 BLG0L00 #12 MAIN SHED

GW1 LEAF BLOWER (E) GREEN WORKS PRO GWW0630643 BLG0L00 #12 MAIN SHED

BC1 POWER WASHER BLUE CLEAN 1.37715E+12 AR3838 #12 MAIN SHED

MM4 POWER WASHER MITM 11052495 WP-3000-OMHB #12 MAIN SHED

MM2 POWER WASHER MITM 11053165 WP-3000-OMHB #12 MAIN SHED

MM5 POWER WASHER MITM 11053164 WP-3000-OMHB #12 MAIN SHED

MM3 POWER WASHER MITM 11052496 WP-3000-OMHB #12 MAIN SHED

TB4 WEED WACKER TROYBILT 1K205DB2604 TB22 # 13 SMALL SHED (BROKEN)

NO # WEED WACKER TROYBILT 1I165OC2076 TB22EC # 13 SMALL SHED (BROKEN)

NO # WEED WACKER TROYBILT 1I277DK1316 TB525EC # 13 SMALL SHED (BROKEN)

HW10 WEED WACKER HUSQVARNA 19211N300910 128LD #12 MAIN SHED

NO # WEED WACKER HUSQVARNA 19042N300351 128CD #12 MAIN SHED

HW5 WEED WACKER HUSQVARNA 19024N300653 128LD #12 MAIN SHED

HW9 WEED WACKER HUSQVARNA 19315N300677 128LD #12 MAIN SHED

NO # WEED WACKER HUSQVARNA 183700065 322L #12 MAIN SHED

NO # WEED WACKER (E) WORX 2.01411E+11 WGI60 #12 MAIN SHED

NO # WEED WACKER (E) WORX 2.01411E+11 WGI60 #12 MAIN SHED

X4 WEED WACKER (E) WORX 2.01411E+11 WGI60 #12 MAIN SHED

X5 WEED WACKER (E) WORX 2.01411E+11 WGI60 #12 MAIN SHED

X10 WEED WACKER (E) WORX 2.01731E+11 WGI163.9 #12 MAIN SHED

X6 WEED WACKER (E) WORX 2.01731E+11 WGI163.9 #12 MAIN SHED

X5 WEED WACKER (E) WORX 2.01731E+11 WGI163.9 #12 MAIN SHED

X7 WEED WACKER (E) WORX 2.01731E+11 WGI163.9 #12 MAIN SHED

X9 WEED WACKER (E) WORX 2.01731E+11 WGI163.9 #12 MAIN SHED

NO # WEED WACKER TROYBILT 1H237DB1433 TB35EC #12 MAIN SHED (BROKEN)

NO # WEED WACKER TROYBILT 1D186DH3199 TB22 #12 MAIN SHED (BROKEN)

NO # WEED WACKER TROYBILT 1L27DK1304 TB525EC #12 MAIN SHED (BROKEN)

WB2 WHEEL BARROW TRUE TEMPER YARD

NO # WHEEL BARROW KOBALT YARD (BROKEN)

DESCRIPTION BRAND SERIAL NUMBER MODEL NUMBER LOCATION

AIRLESS PAINT SPRAYE GRACO BA0236 1095 Paint Shop AIRLESS PAINT SPRAYE GRACO BA122 695 Paint Shop AIRLESS PAINT SPRAYE GRA BA28420 390PC Paint Shop WASHER MAYTAG CD42503607 MHWC7500YWO Paint Shop DRYER MAYTAG CA42700162 MED7500YW Paint Shop FRIDGE WHIRLPOOL SW1623130 FD5FHEXTS01 Paint Shop AIR CONDITIONER FRIGIDAIRE KK31937175 FRA086ATZ Paint Shop WATER DISPENSER PRIMO 2999 601144 Paint Shop

DESCRIPTION BRAND SERIAL NUMBERMODEL NUMBER Location CHAIN SAW HUSQVARNA 460 RANCHER Shed #3 CHAIN SAW HUSQVARNA 460 RANCHER Shed #3 CHAIN SAW HUSQVARNA 460 RANCHER Shed #3 CHAIN SAW HUSQVARNA 460 RANCHER Shed #3 CHAIN SAW STIHL MS361 Shed #3 CHAIN SAW STIHL MS361 Shed #3 CONCRETE SAW MAKITA 1002320180 DPC7331 Shed #3 CONCRETE SAW HUSQVARNA 20142600007 K3000 Shed #3 LARGE SIZE SNAKE RIDGID VBF032770510 FS413 Shed #3 MEDIUM SIZE SNAKE RIDGID VVM479311009 K-400 Shed #3 POLE SAW HUSQVARNA 143900223 327P5 Shed #3 POLE SAW HUSQVARNA 143900301 327P5 Shed #3 SUB PUMP TSURUMI 14439021297 HS24S Shed #3 SUB PUMP ZOELLER 2670004 E267F Shed #3 SUB PUMP ZOELLER 2670004 E267F Shed #3 VIDEO CAM SNAKE VIZ TRAC 914288 Shed #3 WALK BEHIND CONCRETE SAW HUSQVARNA 20143600014 FS413 Shed #3 WEED WACKER HUSQVARNA 183600008 322L Shed #3

DESCRIPTION BRAND SERIAL NUMBERMODEL NUMBER Location DEHUMIDIFIER FRIEDRICH AAED03314 D70B (BROKEN) Shed #5 DEHUMIDIFIER FRIEDRICH AAED03311 D70B (BROKEN) Shed #5 DEHUMIDIFIER FRIEDRICH AAED03539 D70B (BROKEN) Shed #5 DEHUMIDIFIER LG LD650EAL Shed #5 DEHUMIDIFIER FRIGIDAIRE KN90206670 FAD301NWDA1 Shed #5 DEHUMIDIFIER SOLEUSAIR 10034610743 GLDEH45F293 Shed #5 DEHUMIDIFIER FRIEDRICH AAED03526 D70B (BROKEN) Shed #5 HEATER MOUNT POWER HOUSE NPH4AB Shed #5 PROPANE HEATER (FLOOR) PROTEMP HCH121009472 PT18PCHA Shed #5 PROPANE HEATER (SMALL) MR HEATER MH9BX Shed #5 PROPANE HEATER (SMALL) MR HEATER MH9BX Shed #5 PROPANE HEATER (MEDIUM) MR HEATER EC7480014093251 MH18B Shed #5 SPACE HEATER (SMALL) LAKEWOOD 792AA Shed #5 SPACE HEATER (SMALL) PELONIS HF0003 Shed #5 SPACE HEATER (SMALL) PELONIS HF0003 Shed #5 SPACE HEATER (SMALL) PELONIS HF0003 Shed #5 SPACE HEATER (SMALL) PELONIS NT2012D Shed #5 SPACE HEATER (SMALL) SOLEIL LH878 Shed #5 SPACE HEATER (SMALL) SOLEIL LH878 Shed #5 SPACE HEATER (SMALL) SOLEIL LH878 Shed #5 SPACE HEATER (SMALL) SOLEIL LH878 Shed #5 SPACE HEATER (FLOOR) PELONIS M02180200920 H00218 (BROKEN) Shed #5 SPACE HEATER (FLOOR) KENWOOD SFMH000001 CYAA45-1 Shed #5 WATER DISPENSER PRIMO 354 601144 Shed #5 WATER DISPENSER PRIMO 2521 601142 Shed #5 WATER DISPENSER PRIMO 601142 (NEW IN BOX) Shed #5 5000 BTU AIR CONDITIONER LG 312CXEAC1924 LW5014 Shed #5 6000 BTU AIR CONDITIONER FRIGIDAIRE KK70327860 FFRA06L281 Shed #5 8000 BTU AIR CONDITIONER LG 205TAZF06197 8W8012ER Shed #5 8000 BTU AIR CONDITIONER LG 205TALB06296 LW8012ER Shed #5 8000 BTU AIR CONDITIONER LG 205TACX06075 LW8012ER Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31936755 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31560227 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31936501 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31406760 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31560237 FRA086AT7 Shed #5

8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31936837 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK3196754 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31565304 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31937187 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31056161 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31937203 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31559805 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK24503705 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31565315 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31510943 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31937163 FRA086AT7 Shed #5 8000 BTU AIR CONDITIONER LG 205TAZF06293 LW8012ER (BROKEN) Shed #5 8000 BTU AIR CONDITIONER FRIGIDAIRE KK31565303 FRA086AT7 (BROKEN) Shed #5 8000 BTU AIR CONDITIONER LG 205TALBO6200 LW8012ER (BROKEN) Shed #5 8000 BTU AIR CONDITIONER LG 205TANS06303 LW8012ER (BROKEN) Shed #5 8000 BTU AIR CONDITIONER FRIGIDIAIRE KK31937182 FRA086AT7 (BROKEN) Shed #5 8000 BTU AIR CONDITIONER FRIGIDAIRE KK31511527 FRA086AT7 (BROKEN) Shed #5 8001 BTU AIR CONDITIONER GOLDSTAR 304KA05596 K68000RY3 (BROKEN) Shed #5 8002 BTU AIR CONDITIONER FRIGIDAIRE KK31560243 FRA086AT7 (BROKEN) Shed #5 8003 BTU AIR CONDITIONER LG 205TAEJ06300 LW8012ER (BROKEN) Shed #5 8004 BTU AIR CONDITIONER LG 402CXASA8680 LW8012ER (BROKEN) Shed #5 9800 BTU AIR CONDITIONER LG 006TALV00168 LT101CNR Shed #5 10000 BTU AIR CONDITIONER FRIGIDAIRE KK90645948 FAC10781A (BROKEN) Shed #5

DESCRIPTION BRAND SERIAL NUMBER MODEL NUMBER Location AIR COMPRESSOR BOSTITCH Shed #6 AIR COMPRESSOR RIDGID 2388 GP90150A Shed #6 AIR COMPRESSOR RIDGID CV090201195 OLS0145MW Shed #6 CONCRETE BASE TAMPER NORTHERN 4114888 MSH160 Shed #6 EARTH AUGER DULLAY EARTHQUAKE013270013410106140303 DULLAY 10003 Shed #6 FLOOR STRIPPER TORNDO 33079 Shed #6 FLOOR STRIPPER TORNDO 33079 Shed #6 HEAT MACHINE NOVATEK 664 Shed #6 HEAT MACHINE NOVATEK 9833 Shed #6 HEAT MACHINE NOVATEK 1237 Shed #6 HYDRO JET JET SET 162728 J145A Shed #6 OIL HEATER DAYTCH 3E219E Shed #6 PAINT…