14. FAA_MSTB_Addendum-001_231115.pdf

ADDENDUM NO. 001

Date of Issue: November 16, 2023

CONTRACT NO. 6973GH-21-D-000044

WORK ORDER 6973GH-22-F-00856

MSTB FACILITY

US DEPT. OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

Prepared by:

108 South Broadway

Edmond, Oklahoma 73034

405.840.1111 (v) 405.840.1191 (f)

Architect

Thomas Small, AIA

11/16/2023

Addendum No. 001 MSTB, FAA-OKC Work Order 6973GH-22-F-00856 Issued: November 15, 2023

Addendum No. 001 forms a part of the Contract Documents and modifies the original bid documents. Items in this Addendum take precedence over the original documents. Addendum No. 001 consists of the following:

General Information:

The purpose of the Addendum is to respond to Bidders questions and revise the construction documents in response.

Revisions are as follows:

1) Drawing revisions to indicate PEMB Batt roof insulation system noted in Specification

Section 07.21.16.

2) Deletion of Allowance specification Section 01 14 00.

3) Addition of Signage information on Sheet A.201 and revised specification section 10

14 00-Signage.

Drawings:

1) Refer to attached Sheet A.201. Signage information has been added to this sheet.

This is a new sheet that replaces, in its entirety, the original A.201 sheet in the Construction Documents.

2) Refer to attached Sheet A.501. Revisions to this sheet are the wall hatch designating the foam insulation. This is a new sheet that replaces, in its entirety, the original A.501 sheet in the Construction Documents.

3) Refer to attached Sheet A.502. Revisions to this sheet include noting the PEMB roof insulation per spec section 07.21.16. This is a new sheet that replaces, in its entirety, the original A.502 sheet in the Construction Documents.

4) Refer to attached Sheet E.801, Revisions to this sheet include noting CBP wireless access points adjacent to FAA wireless access points, conduit size increase to 2” conduit, and additional conduit and junction boxes between IDF Room 106 and FAA Telecom 107. This is a new sheet that replaces, in its entirety, the original E.801sheet in the Construction Documents.

5) Refer to attached Sheet A.702, Revisions to this sheet include noting the PEMB roof insulation per spec section 07.21.16 and revising the details to not show foam insulation on the roof deck. This is a new sheet that replaces, in its entirety, the original sheet A.702 in the Construction Documents.

Specifications:

1) Delete Section 01 14 00-Allowances. The FAA will contract directly with a testing agency to perform the special inspections and test. Therefore, specification section 01 21 00-Allowances shall be deleted from the Construction Documents. Note that normal testing and inspections on this project are the responsibility of the Contractor and are to be included in the contract amount.

Addendum No. 001 MSTB, FAA-OKC Work Order 6973GH-22-F-00856 Issued: November 15, 2023

2) Refer to attached Section 10 14 00-Signage. This section provides additional information on required signage for the Building.

Bid Documents:

None.

Attachments:

1. A.201 Floor Plan

2. A.501 Building Sections

3. A.502 Wall Sections

4. A.702 Wall Section Details

5. A.801 Telecom Plan and Details

6. Specification Section 10 14 00-Signage

- End of Addendum No. 001 -

A.301

A.301

A.301

A.301

AA

BB

CC

30' - 0"20' - 0"5' - 0"20' - 0"20' - 0"

95' - 0"

BAY 2

BAY 3

BAY 4

BAY 1

GEN.

MAINT/STRG.

SYSTEMS

UNI-TLT.

J.C.

STRG.

IDF RM. -

CBP

FAA

TELECOM

ELECT.

RISER

102A103A104A 101A

101B

104B

106A 112A

113A

109A108A107A

102C

A.501

A.501

A.501

102B

A.501

105A

110A 111A 109B

A.401

G

H

A

D

D

DB

A

A

B C

C

B D

RTU-1,

RE:

MECH

GUH-2, RE: MECH GUH-1, RE: MECH

CU-1, RE:

MECH

DCU-1 AND DCU-2,

RE: MECH

CU-1, RE:

MECH

FF-2 ABOVE

DOOR, RE:

MECH

VF-1, RE:

MECH

LV-1, RE:

MECH

LV-3, RE:

MECH

LV-2, RE:

MECH

3' - 0" 14' - 0" 3' - 0"3' - 0" 14' - 0" 3' - 0"3' - 0" 2' - 0"

12' - 0" 4' - 1"

3' - 0"

11" 2' - 6"

4' - 0"

2' - 6" 14' - 0" 7' - 0"

A.701

A.701

A.701

3 A.701

4' - 9"

E01

E02 E05

E05

E05

E04

E03

E05

CONCRETE PAD.

RE:4/M-301

CONC.PAD.

RE:4/M-301

B

B

A

F F F

CONCRETE PAD.

RE:4/M-301

1'

3.2

3.2

20' - 0" 1' - 1"

3' - 4" 6' - 11" 3' - 4" 5' - 4" 3' - 4" 1' - 8"

20' - 0" 9' - 0" 14' - 0" 7' - 0"

95' - 0"

10' - 10" 13' - 11 1/2" 20' - 2 1/2"

4' - 5 1/8"

1"

65' - 0" 30' - 0"

METAL BUILDING COLUMN,

PAINT TO MATCH WALL

PANELS

20' - 0" 25' - 0"

45' - 0" 30' - 0"

CLR.

1' - 10"2' - 6"2' - 6"

DESIGNED

WORK ORDER NO.

DRAWN

OFFICE OF

ISSUED BY DATE:

PREPARED BY

REV DATE

APPROVED BY

DESCRIPTION APP'DCHECK

OF

ADD

DAP

2020-042069

REVIEWED BY

DRAWING NO.

MIKE MONRONEY AERONAUTICAL CENTER - OKLAHOMA CITY, OKLAHOMA

FACILITY MANAGEMENT

AMP-400

FEDERAL AVIATION ADMINISTRATION

DEPARTMENT OF TRANSPORTATION

MSTB FACILITY

SMALL ARCHITECTS HAROLD STONG

100% FOR CONSTRUCTION SUBMISSION

SENSITIVE SECURITY INFORMATION WARNING: This record contains Sensitive Security Information that is controlled under 49 CFR parts 15 and 1520. No part of this record may be disclosed to persons without a

"need to know", as defined in 49 CFR parts 15 and 1520, except with written permission of the Secretary of Transportation. Unauthorized release may result in civil penalty or other action. For U.S. government agencies, public disclosure is governed by 5 U.S.C. 552 and 49 CFR parts 15 and 1520.

CONTRACT No. 6973GH-21-D-000044

FLOOR PLAN

A.201

October 17, 2023

26 75

1/8" = 1'-0"A.201

FLOOR PLAN & EQUIPMENT

SCHEDULE

EQUIPMENT SCHEDULE

MARK ACCESSORY QUANTITY INSTALLATION

MANUFACTURER (OR

EQUAL) MODEL NUMBER

E01 AIR COMPRESSOR 1 C.F/C.I QUINCY QGS-10 17

E02

EMERGENCY EYE WASH

W/SHOWER 2 C.F./C.I BRADLEY S19314SPR

E03

TWO TON, 1 BAY

BRIDGE CRANE.

208-VOLT, 3-PHASE

1 C.F/C.I

SPANCO /

HARRINGTON NER 02 0L

E04

2 PERSON FALL

ARREST SYSTEM 1 C.F/C.I RIGID LIFELINES PT 500

E05 AIR HOSE REEL 4 C.F/C.I GLOBAL

3/8" x 50' HOSE REEL W/50'

HOSE,300 PSL

GENERAL NOTES:

1. REFER TO SHEET M-201 FOR DUCTWORK

LAYOUT.

2. REFER TO SHEET P-201 FOR ROUTING OF

COMPRESSED AIR LINES.

3. REFER TO SHEET E-901 FOR WAP LOCATIONS.

COORDINATE FINAL LOCATIONS WITH USER.

4. CONTRACTOR SHALL PROVIDE AND INSTALL

IGNITION BARRIER ON ALL EXPOSED SPRAY

FOAM INSULATION IN THE BUILDING.

5. ALL EXTERIOR DIMENSIONS TAKEN FROM PEMB

GRIDLINES AND FACE OF OPENINGS.

6. ALL INTERIOR DIMENSIONS TAKEN FROM PEMB

GRID LINES AND CENTERLINE OF METAL STUD

PARTITIONS.

7. AT DOWNSPOUTS LOCATIONS DISCHARGING

ONTO LAWN AREAS, PROVIDE AND INSTALL

SPLASHBLOCKS.

SIGNAGE SCHEDULE

MARK

SIGN TYPE

PER

SECTION

10 14 00 SIGN TEXT

1 TYPE 1B GEN. MAINTENANCE 109

2 TYPE 1B JANITOR 111

3 TYPE 2R RESTROOM (SIGN 1) 110 (SIGN 2)

4 TYPE 1B STORAGE 105

5 TYPE 1A 106

6 TYPE 1A 112

7 TYPE 1B ELECTRICAL 113

8 TYPE 1B FIRE RISER ROOM - SEE NOTE #1

9 TYPE 1A 107 - SEE NOTE #1

SIGNAGE NOTE:

1. PROVIDE SIGNAGE PER SPECIFICATION SECTION 14 10 00-SIGNAGE ON ALUMINUM IN LIEU

OF PLASTIC MATERIAL.

1 11/16/23 ADDENDUM #1

ADD 1

FINISH FLOOR

100' - 0"

RIDGE

136' - 9"

A.501

A.501

A.501

PRE-FINISHED METAL

ROOF PANELS BY PEMB

MANUFACTURER, TYP.

PRE-FINISHED METAL

WALL PANEL

BY PEMB

MANUFACTURER, TYP.

RIGID FRAME BY

PEMB MANUFACTURER

PRE-FINISHED METAL WALL

PANEL BY PEMB

MANUFACTURER, TYP.

PRE-FINISHED OVERHEAD

COILING DOOR, TYP.

PRE-FINISHED METAL WALL

PANEL TO 8'-0" A.F.F.

SPRAY FOAM INSULATION WITH

THERMAL BARRIER

PRE-FINISHED METAL WALL

PANEL TO 8'-0" A.F.F.

A.502

A.502

Sim

O.H.

B.O. HIGH WINDOW

126' - 0"

110 109 108 107

105A110A111A109B

101B

BAY 4

BAY 3

BAY 2

BAY 1

101 105112

5" CONC. SLAB ON

VAPOR BARRIER ON

4" GRAVEL BASE ON

SUB BASE. RE: S.200

SELF SUPPORTING, ONE TON,

SINGLE BAY, OVERHEAD

BRIDGE CRANE

2-PERSON, SUSPENDED

FALLARREST MONORAIL

SYSTEM, BRACE RAIL TO

STRUCTURE ABOVE 8'-0" O.C

PEMB ROOF

INSULATION W/ LINER

FINISH FLOOR

100' - 0"

EAVE

130' - 0"

RIDGE

136' - 9"

A.501

PRE-FINISHED METAL WALL PANEL

BY PEMB MANUFACTURER, TYP.

PRE-FINISHED METAL

ROOF PANELS BY PEMB

MANUFACTURER, TYP.

PRE-FINISHED METAL

GUTTER & DOWNSPOUTS, TYP.

PRE-FINISHED METAL WALL PANEL

BY PEMB MANUFACTURER, TYP.

PRE-FINISHED OVERHEAD

COILING DOOR, TYP.

SPRAY FOAM INSULATION WITH

THERMAL BARRIER

PRE-FINISHED METAL WALL

PANEL TO 8'-0" A.F.F.

RIGID FRAME BY PEMB MANUFACTURER.

A.502

A.502

Sim

PRE-FINISHED OVERHEAD

COILING DOOR, TYP.

PRE-FINISHED METAL ROOF PANELS

BY PEMB MANUFACTURER, TYP.

B.O. WINDOW

120' - 0"

B.O. HIGH WINDOW

126' - 0"

101B101A

112 111BAY 1

5" CONC. SLAB ON

VAPOR BARRIER ON

4" GRAVEL BASE ON

SUB BASE. RE: S.200

PAVING. RE: CIVIL

SELF SUPPORTING, ONE TON,

SINGLE BAY, OVERHEAD

BRIDGE CRANE.

2-PERSON, SUSPENDED FALLARREST

MONORAIL SYSTEM, BRACE RAIL TO

STRUCTURE ABOVE 8'-0" O.C

< 8' MAX CENTERS

7' - 10 1/2"

PEMB ROOF

INSULATION W/ LINER 2

FINISH FLOOR

100' - 0"

EAVE

130' - 0"

RIDGE

136' - 9"

LOW EAVE

118' - 4"

A.501

PRE-FINISHED METAL ROOF PANELS

BY PEMB MANUFACTURER, TYP.

PRE-FINISHED METAL

GUTTER & DOWNSPOUTS, TYP.

PRE-FINISHED METAL WALL PANEL

BY PEMB MANUFACTURER, TYP.

PRE-FINISHED OVERHEAD

COILING DOOR, TYP.

SPRAY FOAM INSULATION WITH

THERMAL BARRIER

PRE-FINISHED METAL WALL

PANEL TO 8'-0" A.F.F.

PRE-FINISHED

METAL

GUTTER &

DOWNSPOUTS, TYP.

PRE-FINISHED METAL ROOF PANELS

BY PEMB MANUFACTURER, TYP.

SPRAY FOAM INSULATION WITH

THERMAL BARRIER

PRE-FINISHED METAL ROOF PANELS

BY PEMB MANUFACTURER, TYP.

PRE-FINISHED METAL WALL PANEL

BY PEMB MANUFACTURER, TYP.

SUSPENDED GYPSUM CEILING

10'-0" A.F.F., PAINTED TYP.

METAL DOOR &

METAL FRAME

(PAINTED)

A.502

Sim O.H.

A.502

A.502

B.O. WINDOW

120' - 0"

B.O. HIGH WINDOW

126' - 0"

102A

102C

112A

BAY 2

J.C.

SYSTEMS

ELECT.

GEN.

MAINT/STRG.

5" CONC. SLAB ON

VAPOR BARRIER ON

4" GRAVEL BASE ON

SUB BASE. RE: S.200

PEMB ROOF

INSULATION W/ LINER

FINISH FLOOR

100' - 0"

EAVE

130' - 0"

RIDGE

136' - 9"

LOW EAVE

118' - 4"

A.501

PRE-FINISHED METAL ROOF PANELS

BY PEMB MANUFACTURER, TYP.

PRE-FINISHED METAL

WALL PANEL

BY PEMB

MANUFACTURER, TYP.

SPRAY FOAM INSULATION WITH

THERMAL BARRIER

PRE-FINISHED METAL

GUTTER & DOWNSPOUTS, TYP.

PRE-FINISHED METAL ROOF PANELS

BY PEMB MANUFACTURER, TYP.

PRE-FINISHED METAL

ROOF PANELS BY PEMB

MANUFACTURER, TYP.

PRE-FINISHED METAL

GUTTER & DOWNSPOUTS, TYP.

PRE-FINISHED METAL WALL

PANEL BY PEMB

MANUFACTURER, TYP.

PRE-FINISHED OVERHEAD

COILING DOOR, TYP.

PRE-FINISHED METAL WALL

PANEL TO 8'-0" A.F.F.

METAL DOOR &

METAL FRAME (PAINTED)

RIGID FRAME BY PEMB

MANUFACTURER.

A.502

B.O. WINDOW

120' - 0"

B.O. HIGH WINDOW

126' - 0"

BAY 4

104102C

5" CONC. SLAB ON

VAPOR BARRIER ON

4" GRAVEL BASE ON

SUB BASE. RE: S.200

PAVING. RE: CIVIL

A.502

Sim

PEMB ROOF

INSULATION W/ LINER

DESIGNED

WORK ORDER NO.

DRAWN

OFFICE OF

ISSUED BY DATE:

PREPARED BY

REV DATE

APPROVED BY

DESCRIPTION APP'DCHECK

OF

ADD

DAP

2020-042069

REVIEWED BY

DRAWING NO.

MIKE MONRONEY AERONAUTICAL CENTER - OKLAHOMA CITY, OKLAHOMA

FACILITY MANAGEMENT

AMP-400

FEDERAL AVIATION ADMINISTRATION

DEPARTMENT OF TRANSPORTATION

MSTB FACILITY

SMALL ARCHITECTS HAROLD STONG

100% FOR CONSTRUCTION SUBMISSION

1 3/18/22 RESPONSE TO 100% REVIEW COMMENTS

SENSITIVE SECURITY INFORMATION WARNING: This record contains Sensitive Security Information that is controlled under 49 CFR parts 15 and 1520. No part of this record may be disclosed to persons without a

"need to know", as defined in 49 CFR parts 15 and 1520, except with written permission of the Secretary of Transportation. Unauthorized release may result in civil penalty or other action. For U.S. government agencies, public disclosure is governed by 5 U.S.C. 552 and 49 CFR parts 15 and 1520.

CONTRACT No. 6973GH-21-D-000044

BUILDING SECTIONS

A.501

November 23, 2022

31 75

1/8" = 1'-0"A.501

1 BUILDING SECTION 1 1/8" = 1'-0"A.501

2 BUILDING SECTION 4

1/8" = 1'-0"A.501

3 BUILDING SECTION 3

1/8" = 1'-0"A.501

4 BUILDING SECTION 2

FINISH FLOOR

100' - 0"

A.602

Sim

A.602

Sim

6" CONC. FILLED BOLLARD

18"

TYP.

SLAB ON GRADE

A.702

A.702

BAY 4

FINISH FLOOR

100' - 0"

EAVE

130' - 0"

A.601

Sim

A.601

Sim

A.602

Sim

O.H.

O.H.

A.602

Sim

A.702

A.F.F

18"

TYP.

B.O. WINDOW

120' - 0"

BAY 4

FINISH FLOOR

100' - 0"

LOW EAVE

118' - 4"

A.702

Sim

18"

TYP.

A.702

Sim

GEN.

MAINT/STRG.

FINISH FLOOR

100' - 0"

RIDGE

136' - 9"

A.602

Sim

A.602

Sim

A.601

Sim

A.601

SimO.H.

O.H.

A.702

Sim

A.702

Sim

18"

TYP.

B.O. HIGH WINDOW

126' - 0"

ARCHITECTURAL

STANDING SEAM

METAL ROOF PANELS

BAY 1

FINISH FLOOR

100' - 0"

RIDGE

136' - 9"

A.602

Sim

A.602

Sim

A.702

A.702

A.702

Sim

B.O. HIGH WINDOW

126' - 0"

J.C.

BAY 2

DESIGNED

WORK ORDER NO.

DRAWN

OFFICE OF

ISSUED BY DATE:

PREPARED BY

REV DATE

APPROVED BY

DESCRIPTION APP'DCHECK

OF

ADD

DAP

2020-042069

REVIEWED BY

DRAWING NO.

MIKE MONRONEY AERONAUTICAL CENTER - OKLAHOMA CITY, OKLAHOMA

FACILITY MANAGEMENT

AMP-400

FEDERAL AVIATION ADMINISTRATION

DEPARTMENT OF TRANSPORTATION

MSTB FACILITY

SMALL ARCHITECTS HAROLD STONG

100% FOR CONSTRUCTION SUBMISSION

1 3/18/22 RESPONSE TO 100% REVIEW COMMENTS

SENSITIVE SECURITY INFORMATION WARNING: This record contains Sensitive Security Information that is controlled under 49 CFR parts 15 and 1520. No part of this record may be disclosed to persons without a

"need to know", as defined in 49 CFR parts 15 and 1520, except with written permission of the Secretary of Transportation. Unauthorized release may result in civil penalty or other action. For U.S. government agencies, public disclosure is governed by 5 U.S.C. 552 and 49 CFR parts 15 and 1520.

CONTRACT No. 6973GH-21-D-000044

WALL SECTIONS

A.502

November 23, 2022

18 751/2" = 1'-0"A.502

1 WALL SECTION 1

1/2" = 1'-0"A.502

4 WALL SECTION 4

1/2" = 1'-0"A.502

5 WALL SECTION 5

1/2" = 1'-0"A.502

3 WALL SECTION 3

ARCHITECTURAL

STANDING SEAM

METAL ROOF PANELS

ARCHITECTURAL STANDING

SEAM METAL ROOF PANELS

PEMB FRAME

STEEL PURLIN

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

ARCHITECTURAL STANDING

SEAM METAL ROOF PANELS

LIGHT FIXTURE, RE:

ELECTRICAL

WINDOW, RE: A.603

ARCHITECTURAL

STANDING SEAM

METAL ROOF PANELS

STEEL PURLIN

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER PEMB FRAME

PRE-FINISHED METAL

WALL PANEL, TYP.

(COLOR TBD.)

WALL MOUNTED FIRE

EXTINGUISHER

SLAB ON GRADE

1/2" = 1'-0"A.502

2 WALL SECTION 2

PEMB FRAME

ARCHITECTURAL STANDING

SEAM METAL ROOF PANELS

PEMB FRAME

PEMB FRAME

PEMB FRAME

METAL SYUD WALL

WITH GYPSUM WALL

BOARD FINSIH

(PAINTED) RE:

WALL TYPES

RUBBER BASE COVE,

RE: SCHEDULE

SUSPENDED

GYPSUM CEILING,

(PAINTED) RE:

CEILING PLAN

CONC. FOOTING, RE: STRUCTURAL

CONC. FOOTING,

RE: STRUCTURAL

STEEL PURLIN

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

(BEYOND)

OPEN

SLAB ON GRADE

PRE-FINISHED METAL

WALL PANEL, TYP.

(COLOR TBD.)

PRE-FINISHED METAL

WALL PANEL, TYP.

(COLOR TBD.)

PRE-FINISHED METAL

WALL PANEL, TYP.

(COLOR TBD.)VF-2 (BEYOND, RE:

MECHANICAL

PRE-FINISHED PEMB

CLOSURE TRIM,

COLOR TBD

PRE-FINISHED METAL

GUTTER AND

DOWNSPOUTS, COLOR

TBD

PRE-FINISHED METAL

GUTTER AND

DOWNSPOUTS, COLOR

TBD

LIGHT FIXTURE, RE:

ELECTRICAL

PRE-FINISHED METAL

WALL PANEL, TYP.

(COLOR TBD.)

LIGHT FIXTURE, RE:

ELECTRICAL

O.H. DOOR, RE:

SCHEDULE

6" CONC. FILLED

BOLLARD

CONC. SPLASH

BLOCK (BEYOND)

ARCHITECTURAL STANDING

SEAM METAL ROOF PANELS

O.H. CRANE

FRAME (BEYOND)

RE: PLAN

WALL MOUNTED FIRE

EXTINGUISHER

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

(BEYOND)

SPRAY FOAM INSULATION

WITH THERMAL BARRIER

(BEYOND)

STEEL PURLIN

PRE-FINISHED METAL

GUTTER AND

DOWNSPOUTS, COLOR

TBD

6" CONC. FILLED

BOLLARD

CONC. FOOTING,

RE: STRUCTURAL

CONC. FOOTING,

RE: STRUCTURAL

6" CONC. FILLED

BOLLARD

STEEL PURLIN

PRE-FINISHED

METAL WALL

PANEL AND FURR-

OUT, COLOR TBD

PRE-FINISHED

METAL WALL

PANEL AND FURR-

OUT, COLOR TBD

O.H. CRANE

FRAME (BEYOND)

RE: PLAN

O.H. CRANE

FRAME BASE

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

MOP SINK, RE

MECHANICAL

O.H.

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

O.H. DOOR, RE:

SCHEDULE

O.H. DOOR, HOUSING, RE:

MANUFACTURER

PEMB ROOF

INSULATION W/

LINER

PEMB ROOF

INSULATION

W/ LINER

PEMB ROOF

INSULATION

PEMB ROOF

INSULATION W/

LINER

PEMB ROOF

INSULATION W/

LINER

PEMB ROOF

INSULATION

W/ LINER

PRE-FINISHED METAL PANEL TO 8'-0"

A.F.F. AT INTERIOR (COLOR TBD)

CONC. SLAB ON SPECIFIED BASE,

RE: STRUCTURAL

STEEL RE-INFORCING,

RE: STRUCTURAL

PRE-FINISHED METAL PANEL (COLOR

TBD)

METAL STUD FRAMING

NOTCH CONCRETE,

CONTRACTOR COORDINATE

WITH METAL PEMB ERECTOR

FINISHED GRADE, RE: CIVIL

CONC. FOOTING, RE: STRUCTURAL

DRAWING FOR FOUNDATION DETAIL

PEMB STEEL FRAME

PRE-FINISHED METAL

WALL PANEL (COLOR

TBD)

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

PEMB PRE-FINISHED

METAL CLOSURE

TRIM (COLOR TBD)

INSIDE CLOSURE,

TAPED TOP AND

BOTTOM OF PANEL

VF-2 (BEYOND), RE:

MECHANICAL

METAL ROOF PANEL,

TYP. COLOR: BRONZE

PEMB STEEL PURLIN

PEMB STEEL ANGLE

PEMB ROOF

INSULATION W/

LINER

PEMB STEEL

FRAME (BEYOND)

PEMB EAVE STRUT

STEEL PURLIN

PRE-FINISHED METAL

WALL PANEL (COLOR

TBD)

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

STEEL PURLIN

METAL ROOF PANEL, TYP.

COLOR: BRONZE

PEMB CLOSURE

METAL

INSIDE CLOSURE,

TAPED TOP AND

BOTTOM OF PANEL

PEMB ROOF

INSUATION W/ LINER

STEEL PURLIN

PEMB FRAME

(BEYOND)

METAL ROOF PANEL, TYP.

COLOR: BRONZE

INSIDE CLOSURE

TAPE

METAL GUTTER AND DOWN

SPOUTS, (PAINTED) TYP.

COLOR: COBBLE BROWN

(SW#6082)

PRE-FINISHED

METAL WALL PANEL

(COLOR TBD)

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

STEEL PURLIN

PRE-FINISHED GUTTER

CLIP, 24" O.C.

PEMB ROOF

INSULATION

W/LINER

STEEL PURLIN

PEMB FRAME

(BEYOND)

METAL ROOF PANEL,

TYP. COLOR: BRONZE

INSIDE CLOSURE

TAPE

PRE-FINISHED

METAL WALL PANEL

(COLOR TBD)

PRE-FINISHED

METAL WALL PANEL

(COLOR TBD)

SPRAY FOAM

INSULATION WITH

THERMAL BARRIER

PEMB ROOF

INSULATION W/

LINER

PRE-FINISHED METAL

WALL PANEL (BEYOND)

5/8" GYPSUM, WALL BOARD

(PAINTED) (BEYOND)

RUBBER BASE COVE (BEYOND)

RE: SCHEDULE

PEMB STEEL COLUMN

STEEL RE-INFORCING, RE: STRUCTURAL

CONC. SLAB ON SPECIFIED BASE,

RE: STRUCURAL

CONC. FOOTING, RE:

STRUCTURAL DRAWING FOR

FOUNDATION DETAIL

DESIGNED

WORK ORDER NO.

DRAWN

OFFICE OF

ISSUED BY DATE:

PREPARED BY

REV DATE

APPROVED BY

DESCRIPTION APP'DCHECK

OF

ADD

DAP

2020-042069

REVIEWED BY

DRAWING NO.

MIKE MONRONEY AERONAUTICAL CENTER - OKLAHOMA CITY, OKLAHOMA

FACILITY MANAGEMENT

AMP-400

FEDERAL AVIATION ADMINISTRATION

DEPARTMENT OF TRANSPORTATION

MSTB FACILITY

SMALL ARCHITECTS HAROLD STONG

100% FOR CONSTRUCTION SUBMISSION

1 3/18/22 RESPONSE TO 100% REVIEW COMMENTS

SENSITIVE SECURITY INFORMATION WARNING: This record contains Sensitive Security Information that is controlled under 49 CFR parts 15 and 1520. No part of this record may be disclosed to persons without a

"need to know", as defined in 49 CFR parts 15 and 1520, except with written permission of the Secretary of Transportation. Unauthorized release may result in civil penalty or other action. For U.S. government agencies, public disclosure is governed by 5 U.S.C. 552 and 49 CFR parts 15 and 1520.

CONTRACT No. 6973GH-21-D-000044

SECTION DETAILS

A.702

November 23, 2022

36 75

1 1/2" = 1'-0"A.702

1 DETAIL SECTION - CONC. FOOTING

1 1/2" = 1'-0"A.702

2 DETAIL SECTION - LOWER RAKE

1 1/2" = 1'-0"A.702

3 DETAIL SECTION - HIGH RIDGE

1 1/2" = 1'-0"A.702

4 DETAIL SECTION - EAVE & GUTTER

1 1/2" = 1'-0"A.702

6 DETAIL SECTION - LOW EVE

1 1/2" = 1'-0"A.702

DETAIL SECTION - MID-SLAB

FOOTING

GENERAL NOTES:

1. ROOF PANLE COLOR TO BE CHOSEN FROM MANUFACTURER'S STANDARD COLOR SELECTION.

2. PAINTED METAL (DOORS, WINDOW FRAMES, EXPOSED STEEL STRUCTURE) COLOR: COBBLE BROWN (SW#6082).

OWNER MAY CHOOSE ALTERNATE COLOR FROM SHERWIN WILLIAMS COLOR SELECTIONS

3. WALL PANEL COLOR BE CHOSEN FROM MANUFACTURER'S STANDARD COLOR SELECTION.

4. METAL BUILDING TRIM COLOR TO BE CHOSEN FROM STANDARD MANUFACTURER'S COLOR SELECTION.

5. MECHANICAL LOUVER COLOR TO BE CHOSEN FROM MANUFACTURER'S STANDARD COLRO SELECTION.

SENSITIVE SECURITY INFORMATION WARNING: This record contains Sensitive Security Information that is controlled under 49 CFR parts 15 and 1520. No part of this record may be disclosed to persons without a "need to know", as defined in 49 CFR parts 15 and 1520, except with written permission of the Secretary of Transportation. Unauthorized release may result in civil penalty or other action. For U.S. government agencies, public disclosure is governed by 5 U.S.C. 552 and 49 CFR parts 15 and 1520.

CONTRACT No. 6973GH-21-D-000044

P:

\2

\E

1.

dw g, 1/

/2

:2 3:

A

M , d na sa lro ad

D

W G

To P

D F-

X2

2.

pc

W.O. 2020-042069 / FAA-MMAC

Mobile Systems Test Bed Facility

(MSTB)

10.14.00 - 1 Signage

SECTION 10.14.00

SIGNAGE

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Room and door signs.

1.02 REFERENCE STANDARDS

A. 36 CFR 1191 - Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities; Architectural Barriers Act (ABA) Accessibility Guidelines current edition.

B. ADA Standards - Americans with Disabilities Act (ADA) Standards for Accessible Design 2010.

C. ICC A117.1 - Accessible and Usable Buildings and Facilities 2009.

1.03 SUBMITTALS

A. See Section 01.30.00 - Administrative Requirements, for submittal procedures.

B. Product Data: Manufacturer's printed product literature for each type of sign, indicating sign styles, font, foreground and background colors, locations, overall dimensions of each sign.

C. Signage Schedule: Provide information sufficient to completely define each sign for fabrication, including room number, room name, other text to be applied, sign and letter sizes, fonts, and colors.

D. Manufacturer's Qualification Statement.

1.04 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing the products specified in this section with minimum three years of documented experience.

1.05 DELIVERY, STORAGE, AND HANDLING

A. Package signs as required to prevent damage before installation.

B. Package room and door signs in sequential order of installation, labeled by floor or building.

C. Store tape adhesive at normal room temperature.

1.06 FIELD CONDITIONS

A. Maintain this minimum temperature during and after installation of signs.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Flat Signs:

1. Best Sign Systems, Inc : www.bestsigns.com/#sle.

2. FASTSIGNS ; Rowmark Brand : www.fastsigns.com/#sle.

3. Substitutions: See Section 01.60.00 - Product Requirements.

2.02 SIGNAGE APPLICATIONS

A. Accessibility Compliance: Signs are required to comply with ADA Standards and ICC A117.1 , unless otherwise indicated; in the event of conflicting requirements, comply with the most comprehensive and specific requirements.

B. Room and Door Signs: Provide a sign for every doorway, whether it has a door or not, not including corridors, lobbies, and similar open areas.

1. Sign Type 1: See FAA/MMAC Panel Signage Criteria following this section.

2. Sign Type 2: Flat aluminum sign with reflective panel media as specified.

a. Provide "tactile" signage, with letters raised minimum 1/32 inch (0.8 mm) and Grade II braille.

b. Character Height: 2 inch (50 mm) .

c. Sign Height: 7 inches (175 mm) , unless otherwise indicated.

W.O. 2020-042069 / FAA-MMAC

Mobile Systems Test Bed Facility

(MSTB)

10.14.00 - 2 Signage

3. Fire Riser Room: Identify with text "FIRE RISER ROOM" in contrasting color to background .

4. Service Rooms: Identify with room names and numbers to be determined later, not those indicated on drawings.

5. Rest Rooms: Identify with pictograms, the names "MEN" and "WOMEN", room numbers to be determined later, and braille.

2.03 SIGN TYPES

A. Flat Signs: Signage media without frame.

1. Edges: Square.

2. Corners: Square.

3. Wall Mounting of One-Sided Signs: Concealed or exposed screws .

B. Color and Font: Unless otherwise indicated:

1. Character Font: Helvetica, Arial, or other sans serif font.

2. Character Case: Upper case only.

3. Background Color: Red .

4. Character Color: White color as selected by Owner.

2.04 ACCESSORIES

A. Exposed Screws: Chrome plated.

B. Tape Adhesive: Double sided tape, permanent adhesive.

PART 3 EXECUTION

3.01 EXAMINATION

A. Verify that substrate surfaces are ready to receive work.

3.02 INSTALLATION

A. Install in accordance with manufacturer's instructions.

B. Install neatly, with horizontal edges level.

C. Protect from damage until Date of Substantial Completion; repair or replace damaged items.

END OF SECTION

FAA/MMAC Panel Signage Criteria

1. Sign material is plastic, 1/8" thick, with 1/2" radius corners, and no borders.

2. All versions of sign types 1, 2 and 3 are 8" square; refer to sign type and installation details for additional dimensional information.

3. Colors must be an integral part of the plastic or applied to the back surface of a translucent panel; painted sign faces are not acceptable without an approved request for substitution, subject to construction contract.

4. Submittal requirements include shop drawings, samples of each sign type, and samples of available/requested colors for review and/or selection.

5. The FAA will provide a sign location map and a sign schedule shortly before substantial completion of the construction contract; do not expect signage or CCMS room numbers to match contract documents.

6. Sign panels must contrast with the substrate, and characters/pictograms

(typically white) must contrast with the sign panels.

7. Characters and pictograms must be raised in accordance with current

ADA standards to accommodate tactile examination.

8. The standard method of attachment is two 6" lengths of double sided foam tape, positioned horizontally, 1/4" to 1/2" clear from the top and bottom edges of the panel and 1/2" to 1" clear from the sides of the panel.

Exception: Where a base plate is required, the foam tape will be installed across the full width of the base plate and flush to the top and bottom edges of the base plate.

9. Alternative attachment:

a. Where the substrate texture is relatively planar, but too rough to accommodate foam tape, install a 6" square base plate

(plastic or painted metal) attached to the substrate with a countersunk screw 1/2" to 3/4" from each corner of the plate.

The screws/inserts must be appropriate for the substrate(s) and the base plate must be centered on the intended location of the panel sign. Conceal all fasteners.

b. Where the substrate is very rough (e.g., split-face CMU), the base plate must be installed with stand-offs; refer to sample detail and coordinate with FAA COR. Conceal all fasteners.

c. Where a substrate is transparent, install a blank sign panel on the opposite side of the substrate, aligned with the sign panel.

10. These criteria are in strict accordance with current ADA standards and FAA/MMAC guidelines - deviations are not recommended.

11. Room names shall be limited to the following:

BOILER COMM. CONFERENCE

ELECTRICAL EQUIPMENT MECHANICAL

MEN RESTROOM WOMEN

JANITOR STAIRS STORAGE

12. A sign-positioning template is recommended for accurate installation.

13. Available local vendors include, but are not limited to:

Architectural Sign & Graphics, 839 Industrial Drive, Yukon, 354-8829 and; FastSigns, 1401 S. Meridian Ave., OKC, 943-3278.

Refer to Rowmark brand for plastic selection.

Irregular substrate

(split-face CMU)

Panel sign

Foam tape

Countersunk

(CSK) screw

Cylindrical stand-off

Base plate

3/8" clear, maximum

SAMPLE DETAIL

Vertical Section

Alternative Attachment

(typ. nylon cut-to-fit)

Foam tape

April 8, 2019

RESTROOM

SIGN TYPE

2M, 2W or 2R

SIGN TYPE

1A BENEATH

RESTROOM

SIGNS, TYP.

WOMENMEN

RESTROOM

STORAGE

GRADE 2

BRAILLE

ROOM

NUMBER

1A

ROOM

NAME

GRADE 2

BRAILLE

GRADE 2

BRAILLE

ROOM

NUMBER

1B

2M 2W

2R

PICTOGRAMS VARY BY

RESTROOM TYPE;

REFER TO SCHEDULE.

INTERNATIONAL SYMBOL

OF ACCESSIBILITY

PER ADA STANDARDS

"MEN", "WOMEN" OR

"RESTROOM" PER SCHEDULE

GRADE 2

BRAILLE

IN CASE

OF FIRE

DO NOT USE

ELEVATORS

USE STAIRS

AUTOMATIC

DOOR

CAUTION

4A 4B

GRAPHIC

SYMBOL:

FIRE

TEXT: 5/8" TALL

GRAPHIC

SYMBOL:

EXIT STAIR

GRADE 2

BRAILLE

FAA/MMAC Panel Signage Criteria

April 8, 2019

Sign Types and Features

STRIKE/LATCH SIDE

OF DOOR FRAME

PLACE ON CALL BUTTON

SIDE OF ELEVATOR DOOR

AUTOMATIC DOOR DECALS:

6" DIAMETER VINYL

EACH LEAF, BOTH SIDES

EACH LEAF, ON

APPROACH SIDE

WHITE

YELLOW

YELLOW

BLACK

BLACK

GREEN

Sign Location Information

FOAM TAPE

FOAM TAPE

SIGN TYPE

1A, 1B or 3

STRIKE/LATCH SIDE

OF DOOR FRAME

END OF SECTION