6973GH-20-R-00145 Amendment 0001 Revisions.docx

6973GH-20-R-00145 Amendment 0001 Revisions

1. Remove “urethane based” from the Specifications, SEC 07 56 00, Part 1, 7.1.0 - Scope, sentence one, and 7.1.1 – Sequence of Operation for VOR Elastomeric Installation item 6.

2. In the specifications, replace SECTION 07 56 00 – FLUID APPLIED ROOFING Part 2 in its entirety with the elastomeric performance spec. listed on pages 2-4 of this document.

3. Contract Drawing ALB-1004541-G005: General note 24: Replace with “The FAA will assist the Contractor in removal and installation of teepee”.

4. Contract Drawing ALB-1004541-G005: General note 25: Replace “250 SQ. FT.” with “500 SQ. FT.”

5. Contract Drawing ALB-1004541-G005: Government Furnished Material note 3: Replace the phrase “Contractor shall” with “FAA will”.

6. Contract Drawing ALB-1004541-D001, Detail A/D001, drawing zone C6, remove “Rosin Paper” from callout note “Contractor to remove: rosin paper, board insulation, and single ply membrane to metal roof.”

7. Contract Drawing ALB-1004541-D001, Detail A/D001, drawing zone B3, Remove callouts “Remove terne roofing (existing)” and “Remove terneplate and hold down clamps from antenna pedestal plate (soldered and screwed)”.

8. Contract Drawing ALB-1004541-A005, Notes 5 and 6, replace “250 SQ.FT.” with “500 SQ.FT.”

9. Contract Drawing ALB-1004541-A005, replace Note 10, with “Not Used”.

10. Contract Drawing ALB-1004541-E001, Detail 3/E001, replace note under title “16 oz. copper sheet .021”thick x 4” wide x 4” long (four required) with “20 oz. copper sheet, (four required)”.

SECTION 07 56 00 – FLUID APPLIED ROOFING

PART 2 – PRODUCTS (REVISED)

7.2.01 Rubber Roof Coating

A. Rubber roof coating products physical specifications and minimum performance criteria shall be in accordance with the following schedules:

1. NEOPRENE FLASHING CEMENT

ADHESIVE BOND Aluminum Q-Panels

2. BRUSH GRADE SEAM SEALER

Recovery from 100% Elongation 100%

Dry film thickness @ 1 gal/100 sq. ft. 6 mils

Recovery from 100% Elongation 100%

7.2.02 Rust Remover and Conditioner

A. Rust remover compound shall be a safe, non-toxic, non-flammable formulation which effectively conditions rust. In addition to treating rust and corrosion, product shall remove oil and dirt and prepares the surface for coating.

TYPICAL PROPERTIES

7.2.03 Polyester Membrane

A. Reinforcing membrane shall be composed of warp knit, 100% polyester yarn fibers offering an excellent combination of high strength and elongation to accommodate unusual stress forces from thermal shock or building movement.

TYPICAL PROPERTIES

7.2.04 Manufacturers

A. The following roof coating manufacturers are approved for this project. Substitutions shall be approved after submission showing compliance with the required product technical properties as listed above.

Truco, Inc.

4301 Train Avenue Cleveland, OH 44113

(800) 227-4569

Western Colloid N.C., Inc.

700 71st Ave.

Oakland, CA 94621 510-430-0270

Pacific Polymers 12271 Monarch St.

Garden Grove, CA 92841 714-898-0025

Belzona 2000 N.W. 88th Court Miami, FL 33172 305-594-4994

B. Other manufacturers requesting approval must submit acceptable information certifying that they are the direct manufacturer from raw material into the specified product and meet the performance criteria required.