RFI 117 - Electrical Fire Place Cutsheet.pdf

Sideline® Series Electric Fireplace Heater

OWNER’S MANUAL

28” / 36” / 40” / 45” / 50” / 60” / 72” / 84” / 100” Sideline® Series Recessed Electric Fireplace

AC 110-120V 60Hz 1500W

Model #: 80004 / 80011 / 80013 / 80014 / 80015 / 80025 / 80027 / 80028 / 80029 / 80032 / 80043

800.215.1990 sales@thpus.com touchstonehomeproducts.com

TABLE OF CONTENTS

15 Unpacking Your Fireplace

• Parts and Hardware A. Tools Required B. What’s in the Box

• Unpacking and Setup A. Unpacking Instructions

• Wiring A. Testing the Fireplace Prior to Installation B. 3-Prong Outlet Installation C. Hard Wire Connection

18 Installation

• WARNINGS

• Choosing Installation Location

• Removing the Rubber Feet

• Removing the Glass Panel

• Removing the Steel Panel (80013 Sideline Steel only)

• Recessed Installation A. Crystal Ember Installation B. Fire Log Installation

• Wall Mounted Installation

27 Operating Your Fireplace

• Power

• Methods of Operation A. Control Panel B. Remote Control Functions

• Remote Control Operation

• Replacing Remote Control Battery

• Temperature Limiting Control

29 Care and Maintenance

• Cleaning

• Maintenance

30 Warranty

General Information

• CSA Approval Listing Information

• Fireplace Specifications

• Dimensional Drawings

80028 80014 80027 80025 80004 80029 80013 80011 80015 80043 80032

Sideline® 28” Dimensions Sideline® 36” Dimensions Sideline® 40” Dimensions Sideline® 45” Dimensions Sideline® 50” Dimensions Sideline® 50” White Dimensions Sideline® 50” Steel Dimensions Sideline® 60” Dimensions Sideline® 72” Dimensions Sideline® 84” Dimensions Sideline® 100” Dimensions

2 Touchstone Home Products

Table of Contents

• THIS FIREPLACE IS HOT WHEN IN OPERATION AND CAN CAUSE INJURY

• Ensure clearances to combustibles are maintained when building a mantel or shelves above

• the fireplace. Elevated temperatures on the wall or in the air above the fireplace can cause melting,

• discoloration or damage to the decorations, a TV or other electronic components.

• Do not operate fireplace before reading and understanding operating instructions.

• Failure to operate fireplace according to operating instructions could cause fire or injury.

• Risk of injury. This fireplace is HOT when in operation and heating element is ON. Power to the

• fireplace should be turned OFF and the fireplace allowed to cool before servicing. To disconnect

• power to the fireplace, turn controls to OFF, then remove plug from outlet.

• Do not install damaged, incomplete, or substitute components.

• Young children should be carefully supervised when they are in same room with fireplace.

• Toddlers, young children and others may be susceptible to accidental injury. A physical barrier is

• recommended if there are at-risk individuals in the house.

• Clothing and other flammable material should not be placed on or near the fireplace.

• Due to high temperatures, the fireplace should be located out of traffic and away from furniture

• and draperies.

• It is imperative that the control compartments, circulating blower, and its passageway

• to the fireplace are kept clean.

• Under no circumstances should this fireplace be modified.

• Do not use the fireplace if any part has been under water.

• Do not operate the fireplace with the glass panel removed, cracked or broken.

• Keep the packaging material out of the reach of children. As with all plastic bags, these are

• not toys and should be kept away from children and infants.

• Servicing should only be done while the fireplace is disconnected from the power.

• Do not operate this fireplace with a damaged cord or plug, after the fireplace malfunctions,

• has been dropped, or damaged in any manner.

• Do not use outdoors.

• Never locate fireplace where it may fall into a bathtub or other water container.

• Do not run the cord under carpeting. Do not cover cord with throw rugs, runners, or the like.

• Connect to a properly grounded outlet or hard wire connection only.

• Do not insert foreign objects into any ventilation or exhaust opening as this may cause an

• electric shock, fire, or damage to the fireplace.

• To prevent a possible fire, do not block the air intakes or exhaust in any manner. Do not use

• on soft surfaces, like a carpet, where openings may be blocked.

Im portant Safety Inform ation W arning

3800.215.1990 touchstonehomeproducts.com

Important Safety Information Warning

Fireplace Specifications

This fireplace has been tested in accordance with the CSA Standards for fixed and location-dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact our technical support department at 800-215-1990.

Note: This fireplace must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition in the United States or the Canadian Electric Code, CSA C22.1 in Canada.

Model Number

Description

Voltage

Watts

Amps

Fireplace Width

Fireplace Height

Fireplace Depth

Net Weight

Gross Weight

Model Number

Description

Voltage

Watts

Amps

Fireplace Width

Fireplace Height

Fireplace Depth

Net Weight

Gross Weight

Model Number

Description

Voltage

Watts

Amps

Fireplace Width

Fireplace Height

Fireplace Depth

Net Weight

Gross Weight

80028

Sideline® 28

120v AC

Max 1100W

12 AMP

28”

16 1/2”

5 1/2”

25 lb

33 lb

Sideline® 36

120v AC

Max 1500W

12 AMP

36”

21 1/2”

5 1/2”

38 lb

47 lb

80014 80027

Sideline® 40

120v AC

Max 1500W

12 AMP

40”

21 1/2”

5 1/2”

41 lb

49 lb

80025

Sideline® 45

120v AC

Max 1500W

12 AMP

45”

21 1/2”

5 1/2”

55 lb

59 lb

80004

Sideline® 50

120v AC

Max 1500W

12 AMP

50”

21 1/2”

5 1/2”

60 lb

65 lb

80029

Sideline® 50 White

120v AC

Max 1500W

12 AMP

50”

21 1/2”

5 1/2”

60 lb

65 lb

80013

Sideline® 50 Steel

120v AC

Max 1500W

12 AMP

50”

21 3/8”

5 1/2”

60 lb

65 lb

80011

Sideline® 60

120v AC

Max 1500W

12 AMP

60”

21 1/2”

5 1/2”

70 lb

78 lb

80015

Sideline® 72

120v AC

Max 1500W

12 AMP

72”

21 1/2”

5 1/2”

110 lb

150 lb

80043

Sideline® 84

120v AC

Max 1500W

12 AMP

84”

21 1/2”

5 1/2”

125 lb

160 lb

80032

Sideline® 100

120v AC

Max 1500W

12 AMP

100”

21 1/2”

5 1/2”

150 lb

175 lb

4 Touchstone Home Products

CSA Approval Listing Information

80028 - Sideline 28” Recessed Fireplace

FEATURES

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame effect

- Built in timer mode for shut off in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

- Ships with fire log secured in place. To use glass

- crystal media, simply unscrew and remove the log.

SPECIFICATIONS

- Frame color: Black

- Watts: 1100

- BTU’s: 3753

- Room Coverage: 400 ft

- Voltage: 120v

- Amps: 12

- Rough Opening: 23 1/4”W x 15 3/4”H x 5 1/2”D

- Note: the Sideline 28 is not hard wire compatible.

FRONT VIEW

SIDE VIEW

REAR VIEW

TOP VIEW

5800.215.1990 touchstonehomeproducts.com

Sideline® 28” Recessed Fireplace | PN: 80028 Sideline Fireplace D im ensions

80014 - Sideline 36” Recessed Fireplace

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame effect

- Built in timer mode for shut off in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: Black

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 120v

- Amps: 12

- Rough Opening: 32 3/4”W x 20 1/2”H x 5 3/4”D

FRONT VIEW

SIDE VIEW

REAR VIEW

TOP VIEW

6 Touchstone Home Products

Sideline® 36” Recessed Fireplace | PN: 80014

FRONT VIEW

TOP VIEW

80027 - Sideline 40” Recessed Fireplace

FEATURES

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame effect

- Built in timer mode for shut off in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: Black

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 110v - 120v

- Amps: 12

- Rough Opening: 32 3/4”W x 20 1/2”H x 5 3/4”D

SIDE VIEW

BACK VIEW

7800.215.1990 touchstonehomeproducts.com

Sideline Fireplace D im

Sideline® 40” Recessed Fireplace | PN: 80027

80025 - Sideline 45” Recessed Fireplace

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame effect

- Built in timer mode for shut off in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: Black

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 120v

- Amps: 12

- Rough Opening: 40 1/8”W x 20 1/2”H x 5 3/4”D

FRONT VIEW

SIDE VIEW

REAR VIEW

TOP VIEW

8 Touchstone Home Products

Sideline® 45” Recessed Fireplace | PN: 80025

80004 - Sideline 50” Recessed Fireplace - Black 80029 - Sideline 50“ Recessed Fireplace - White

FEATURES

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame e ect

- Built in timer mode for shut o in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: 80004 - Black / 80029 - White

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 110v - 120v

- Amps: 12

- Rough Opening: 47 1/8”W x 20 1/2”H x 5 3/4”W

FRONT VIEW

SIDE VIEW

REAR VIEW

TOP VIEW

Sideline Fireplace D im ensions

9800.215.1990 touchstonehomeproducts.com

Sideline® 50” Recessed Fireplace | PN: 80004 / 80029

SIDE VIEW

REAR VIEW

TOP VIEW

80013 - Sideline Steel 50” Recessed Fireplace

FEATURES

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame effect

- Built in timer mode for shut off in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: Black

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 110v - 120v

- Amps: 12

- Rough Opening: 47 1/8”W x 20 1/2”H x 5 3/4”W

10 Touchstone Home Products

Sideline® Steel 50” Recessed Fireplace | PN: 80013

80011 - Sideline 60” Recessed Fireplace - Black

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame e ect

- Built in timer mode for shut o in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: Black

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 110v - 120v

- Amps: 12

- Rough Opening: 47 1/8”W x 20 1/2”H x 5 3/4”W

FRONT VIEW

SIDE VIEW

REAR VIEW

TOP VIEW

11800.215.1990 touchstonehomeproducts.com

Sideline Fireplace D im

Sideline® 60” Recessed Fireplace | PN: 80011

80015 - Sideline 72” Recessed Fireplace

FEATURES

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame effect

- Built in timer mode for shut off in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: Black

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 110v - 120v

- Amps: 12

- Rough Opening: 68 3/4”W x 20 1/2”H x 5 3/4”D

SIDE VIEW

12 Touchstone Home Products

Sideline® 72” Recessed Fireplace | PN: 80015

KLee Cloud

80043 - Sideline 84” Recessed Fireplace

FEATURES

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame effect

- Built in timer mode for shut off in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: Black

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 110v - 120v

- Amps: 12

- Rough Opening: 80 3/4”W x 20 1/2”H x 5 3/4”D

SIDE VIEW

BACK VIEW

Sideline® 84” Recessed Fireplace | PN: 80043

13800.215.1990 touchstonehomeproducts.com

Sideline Fireplace D im

80032 - Sideline 100” Recessed Fireplace

- 2 heat settings (high and low)

- Designed for recessed mounting in wall

- Remote control for heat and flame setting

- (batteries not included)

- Dual mode, operates with or without heat

- for only flame effect

- Built in timer mode for shut off in 30 minutes

- to 7.5 hours

- Faux Fire Log and Glass Crystal Media Options

SPECIFICATIONS

- Frame color: Black

- Watts: 1500

- BTU’s: 5000

- Room Coverage: 400 ft

- Voltage: 110v-120v

- Amps: 12

- Rough Opening: 96 3/4”W x 20 1/2”H x 5 3/4”D

FRONT VIEW

SIDE VIEW

REAR VIEW

TOP VIEW

14 Touchstone Home Products

Sideline® 100” Recessed Fireplace | PN: 80032

Parts and Hardware

Tools Required

• Phillips screwdriver

• Stud finder

• Level

Unpacking and Setup

Unpacking Instructions:

• Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check the

• parts list to make sure no parts are missing. If parts are missing, please contact technical support at

• 800-215-1990 for replacement.

NOTE: Dispose of plastic bag, as it may cause choking hazard with young children.

Do not let children play with plastic bag.

* Delivered installed

Fireplace - 1

Wood Screws - 6 Drywall Anchors - 6 (Wall mount install use)

Metal Bracket - 2

Plastic Tray* - 1

Remote Control - 1

Crystal Embers - 1 BagFire Log - 1

Wall Bracket* - 1 (Wall mount install use)

What’s in the Box

• Tape measure

• Electric drill

• 1/4” wood drill bit

15800.215.1990 touchstonehomeproducts.com

U npacking Y our Fireplace Unpacking Your Fireplace

The Sideline® series recessed fireplace can either be plugged into a grounded 3-prong outlet or hard wire connection. Note, the Sideline 28 is not hard wire compatible.

Testing the Fireplace Prior to Installation

• Before installing the fireplace, test the fireplace to make sure that it operates properly.

• Plug fireplace into approved outlet and power on fireplace. Once fireplace is tested, continue

• with installation.

• If you have any problems, please contact technical support at 800-215-1990.

3-prong Outlet Installation

• Only use this fireplace on a 120V AC, 15-Amp grounded circuit. Never overload the circuit. If this

• fireplace trips the circuit breaker, unplug all other appliances on the same circuit before the next use.

• Avoid plugging other appliances into the same circuit as this fireplace.

• Always check the fireplace plug and connections before each use.

• Never plug this fireplace into an outlet that is cracked or has any loose wires or connections.

• Plugging this fireplace into a faulty outlet could result in the outlet overheating or catching fire.

• Make sure this plug fits securely into the outlet. Faulty wall outlet connections or loose plugs can cause

• the outlet to overheat. If the outlet or faceplate is hot, discontinue use immediately and have a qualified

• electrician inspect and/or replace the faulty outlet.

• The power cord supplied with the heater has three prongs: two flat blades (live and neutral) and one

• round pin (ground). If a 3-slot receptacle is not available, an adapter MUST be used. The adapter

• MUST be properly grounded to the outlet box (see figure below).

NOTE: Adapter NOT INCLUDED

GROUNDING PIN

METAL

GROUNDING SCREW

ADAPTER

16 Touchstone Home Products

Wiring

If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the household wiring. Note, the Sideline 28 is not hard wire compatible.

This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence of local codes, use the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States or the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada.

A. Remove the cover plate from the right side A. bottom of the appliance by removing the three A. screws, as shown above. Save screws for A. Installation of new cover plate.

C. Remove the power cable and wires from the cover plate. Thread your wiring through the hole C. in the cover plate for connecting to the wires in the Sideline® fireplace.

D. Using the wire connectors, connect the ground green wires (G), the common white wires (N) together, C. then the hot black wires (L) and then the refer to Figure 3.

E. Reinstall the cover plate using the three screws, as shown in Figure 1.

B. Remove the wire connectors from the B. power cord. Keep power cord, in case B. needed in future.

Hard Wire Connection U npacking Y our Fireplace

17800.215.1990 touchstonehomeproducts.com

WARNINGS

• Keep materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least

• 36” away from the front of the fireplace.

• Never install the fireplace where it may fall into a bathtub or other body of water.

• Wear safety gloves and safety glasses for protection during installation. Broken glass may cause

• injury or harm.

• Prevent contact with loose insulation. Do not install the fireplace against a vapor barrier or

• exposed insulation.

• Do not expose the fireplace to the elements (rain, etc.).

Choosing Wall Location

• Measure wall location to ensure that fireplace will fit on desired wall location.

• Minimum clearances (measurements taken from front of glass panel):

• Select a location that is not prone to moisture and is located at least 36” away from materials

• such as curtains, drapes, furniture, or bedding.

• See Safety Information on pages 3 for warnings about safe placement, safe installation, and

• proper use of this product.

Removing the Rubber Feet

• For in-wall, recessed installations, the rubber feet on the bottom of the fireplace are removeable.

• To remove, use a Philips-head screwdriver to remove the four rubber feet on the bottom of the fireplace

• as shown below

Bottom of Fireplace to Floor: 6”

Sides of Fireplace: 6”

Back of Fireplace: 0”

Top of Fireplace: 8” to mantel

Top of Fireplace: 8” to TV

Top of Fireplace: 8” to ceiling

For more detailed instructions, visit our website or Touchstone Home Products YouTube channel for the product support videos.

18 Touchstone Home Products

Installation

REMOVING THE GLASS PANEL

Prior to installation, remove the glass panel. Please remove glass panel as per instructions below:

Instructions

1. There are 2 screws in the top vent opening, one on the far left and one on the far right.

1. Remove both screws from the glass panel.

2. After removing screws, lift glass panel UP and STRAIGHT OUT toward you to remove from

2. fireplace. Place glass panel in a soft, dry place.

2. CAUTION: It is recommended that 2 people remove the glass panel to minimize chance of breakage.

19800.215.1990 touchstonehomeproducts.com

REMOVING THE STEEL PANEL (80013 SIDELINE STEEL ONLY)

Prior to installation, remove the front panel from your 80013 Sideline Steel Fireplace.

Please remove front panel as per instructions below:

Instructions

1. There are 2 screws securing the front panel to the firebox, one on the far left and one on the far right.

1. Remove both screws from the front panel.

2. CAUTION: These screws are for shipping purposes only. They will not be reinstalled

2. when installation is complete.

2. After removing screws, lift glass panel UP and STRAIGHT OUT toward you to remove from

2. fireplace. Place front panel in a soft, dry place.

2. CAUTION: It is recommended that 2 people remove the front panel to minimize chance of breakage.

20 Touchstone Home Products

RECESSED INSTALLATION

• Due to many different finish materials used on walls, it is highly recommended that you consult

• a professional before you install this fireplace in the wall.

• Select a location that is not prone to moisture and is located at least 36” away from materials

• such as curtains, drapes, furniture or bedding.

• In order to avoid the possibility of exposed insulation or vapor barrier coming in contact with the

• fireplace, it is recommended that the walls of the fireplace enclosure be “finished” (ie. Sheetrock,

• drywall, etc) as you would finish any other outside wall of your home. This will ensure that clearance

• to combustibles is maintained within the wall cavity.

• Never install fireplace into load-bearing walls. When recessing fireplace in a wall, recess into

• non-load bearing walls ONLY!

Instructions:

1. Choose a location in the wall to install fireplace.

2. Create opening in the wall that is no more than 1 ⁄4”

2. larger than metal firebox portion of fireplace. The rough

2. opening dimensions for the wall opening is listed in the

2. table on the right.

Firebox Dimensions

MODEL WIDTH HEIGHT DEPTH

80004

80011

80013

80014

80025

80027

80028

80029

80032

80043

46 7/8”

46 7/8”

46 7/8”

32 1/2”

80015 68 3/8”

39 7/8”

32 1/2”

23”

46 7/8”

96 1/2”

80 1/2”

20 1/4”

20 1/4”

20 1/4”

20 1/4”

20 1/4”

20 1/4”

20 1/4”

15 1/2”

20 1/4”

20 1/4”

20 1/4”

5 1/4”

5 1/4”

5 1/4”

5 1/4”

5 1/4”

5 1/4”

5 1/4”

5”

5 1/4”

5 1/4”

5 1/4”

Rough Opening Dimensions

MODEL A (WIDTH) B (HEIGHT) C (DEPTH)

80004

80011

80013

80014

80025

80027

80028

80029

80032

80043

47 1/8”

47 1/8”

47 1/8”

32 3/4”

80015 68 7/8”

40 1/8”

32 3/4”

23 1/4”

47 1/8”

96 3/4”

80 3/4”

20 1/2”

20 1/2”

20 1/2”

20 1/2”

20 1/2”

20 1/2”

20 1/2”

15 3/4”

20 1/2”

20 1/2”

20 1/2”

5 3/4”

5 3/4”

5 3/4”

5 3/4”

5 3/4”

5 3/4”

5 3/4”

5 1/2”

5 3/4”

5 3/4”

5 3/4”

21800.215.1990 touchstonehomeproducts.com

RECESSED INSTALLATION - Continued

1. With the help of a second person, insert fireplace into wall opening and secure with

1. mounting screws provided.

2. Once the fireplace is installed in the wall, place crystal embers or fire log in the fireplace.

Note, the Sideline 28 ships with the log secured in place. Simply unscrew the log on either side to remove and replace with crystal embers.

A. Crystal Ember Installation

1. Carefully, place crystal embers on plastic

2. strip as illustrated in the picture to the right.

2. Apply an even layer from side to side.

22 Touchstone Home Products

RECESSED INSTALLATION - Continued

3. Once completed installing crystal embers or fire log, reinstall glass panel. The hooks on the back

5. of the glass panels fit into the slots on the side of the firebox. Once in the slots, the glass panel goes

5. down and locks into place. Once in place, reinstall 2 locking screws to hold glass securely in place.

A. Fire Log Installation

1. Place fire log in fireplace as illustated below. Note, the Sideline 28 ships with

5. the log fastened in place.

23800.215.1990 touchstonehomeproducts.com

WALL MOUNTED INSTALLATION

• Due to many different finish materials used on walls, it is highly recommended that you

• consult a professional before you install this fireplace on the wall.

• Select a location that is not prone to moisture and is located at least 36” away from materials

• such as curtains, drapes, furniture or bedding.

Instructions

1. With glass panel removed (see p.19 for instructions on removing glass panel), have two people

2. hold the fireplace against the wall to determine the final location.

2. Place the unit face down on a soft, non-abrasive surface. Remove the bracket from the back of

3. the unit by removing the screws holding the bracket to the back of the fireplace.

80004 / 80011 / 80014 / 80025 / 80027 / 80013 / 80029 / 80028 - Wall Bracket Removal (1 bracket)

80015 / 80032 / 80043 - Wall Bracket Removal (2 brackets)

24 Touchstone Home Products

WALL MOUNTED INSTALLATION - Continued

3. Mark location of bracket on wall and then mount the bracket to the wall using the supplied screws

4. and dry wall anchors. The hooks in the bracket MUST be pointed away from the wall, upward, and level.

4. Note: Mount bracket to at least 2 studs. If 2 studs cannot be used, ensure that the supplied dry wall

4. anchors are used to affix the bracket to the wall and the bracket is adequately secured before

4. moving to the next step.

25800.215.1990 touchstonehomeproducts.com

WALL MOUNTED INSTALLATION - Continued

4. With the wall mounting bracket installed, have 2 people lift the fireplace up and insert the 2 hooks

5. on the bracket into the back of the fireplace. The 2 hooks on the mounting bracket will line up with

5. the 2 holes on the back of the fireplace. Once aligned, the hooks will insert into the holes in the back

5. of the fireplace and lock in the down position.

5. Check the fireplace for stability, ensuring that the bracket will not pull free from the wall.

6. Once satisfied, install crystal embers/fire log and reinstall glass panel.

26 Touchstone Home Products

Mounting bracket installed on wall Hang fireplace on mounting bracket hooks

Once the fireplace has been plugged into a grounded outlet, the fireplace is now ready for operation. Ensure that the house circuit breakers for the power supply are turned on.

Power

Plug the power cable into a 110v 15 amp grounded outlet. Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.

Methods of Operation

This electric fireplace can be operated by the CONTROL PANEL, located in the upper right vent in the front glass panel, or by the REMOTE CONTROL. The operation and functions of both methods are the same.

Control Panel and Remote Control Functions

BUTTON FUNCTION ACTION & INDICATION

POWER

TIMER

FLAME

COLOR

HEATER

ON: Enables control panel functions and remote control. Turns on the flame effect.

OFF: Disables control panel functions and remove control. Turns off the flame effect.

FLAME Button: Makes flame effects dimmer or brighter.

NOTE: Flame effect stays on until power button is turned off. Flame effect must be on for heater to turn on.

HEATER Button: Turns heater on and off.

NOTE: The heater only works when the flame effect is on. To prevent overheating, the heater fan will blow cool air for 8-10 seconds before the heater turns on, and after the heater turns off.

TIMER Button: Control time settings to turn off fireplace at selected time.

Settings range from 0.5 hours to 7.5 hours.

COLOR Button: Changes the color of the flame.

1. Press once. Indicator light turns on.

Power turns on. All functions enabled.

2. Press again. Flame effect turns off.

Unit goes to standby. All functions turn off.

1. Press once. Indicator light turns on.

Timer is set to 0.5 hours.

2. Press again until desired setting is reached. Indicator lights show setting.

1. Press once to change the flame brightness.

2. Press again until desired setting is reached.

1. Press once. Indicator lights up. Fan blows cool air for 10 seconds and 750W heater turns on and blows warm air.

2. Press again: Indicator lights up. 1500W heater turns on and blows hot air.

3. Press again. Heater turns off.

1. Press once to change the color of the flame.

2. Press again until desired setting is reached.

O perating Y our Fireplace

27800.215.1990 touchstonehomeproducts.com

Operating Your Fireplace

Remote Control Operation

• This remote control uses 2 AAA batteries (not included).

• To improve operation of the remote control, aim the remote control at the front of the fireplace.

• DO NOT PRESS the buttons too quickly. Give the unit time to respond to each command.

• NOTICE: NEVER dispose of batteries in fire. Failure to observe this precaution may result in

• an explosion. Dispose of batteries at your local hazardous material processing center.

Temperature Limiting Control

This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, the heater will automatically TURN OFF. To reset, please do the following:

1. Unplug the power cord from the outlet.

2. Turn ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes for fireplace to cool down.

3. Inspect the fireplace to make sure no vents are blocked or clogged with dust or lint.

3. If they are, use a vacuum to clean the vent areas.

4. With the POWER switch in the OFF position, plug the power cord back into the outlet.

5. If the problem continues, have your outlet and wiring inspected by a professional.

5. If the outlet is OK, please contact our customer support department at 800-215-1990.

28 Touchstone Home Products

Operating Your Fireplace

CLEANING

• ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning.

• NEVER immerse in water or spray with water. Doing so could result in electric shock, fire,

• or personal injury.

Metal:

• Buff using a soft cloth, slightly dampened with citrus oil-based product.

• DO NOT use brass polish or household cleaners, as these products will damage the metal trim.

Glass:

• Use a good quality glass cleaner sprayed onto a cloth or towel. Dry thoroughly with a paper towel

• or lint- free cloth.

• NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Vents:

• Use a vacuum or duster to remove dust and dirt from the heater and vent areas.

Plastic:

• Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.

• NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

MAINTENANCE

• RISK OF ELECTRIC SHOCK! DO NOT OPEN any panels.

• ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning,

• performing maintenance, or moving the fireplace. Failure to do so could result in electric shock,

• fire, or personal injury.

Electrical and Moving Parts:

• The fan motors are lubricated at the factory and will not require lubrication.

• Electrical components are integrated in the fireplace and are not serviceable by the customer.

Storage:

• Store fireplace in a clean, dry place when not in use.

C are &

M aintenance

29800.215.1990 touchstonehomeproducts.com

Touchstone Home Products, Inc warrants our electric fireplaces to be free of defects in material and workmanship for one year from date of purchase. Touchstone will repair or replace any fireplace or fireplace part that is deemed defective or becomes defective during normal use within one year after the date of purchase.

Electrical components, such as fan motor, heater motor, control board, remote control, and control panel are covered under warranty for one year from date of purchase. Touchstone Home Products will provide replacement parts free of charge during the first year of the warranty.

Replacement parts and fireplace units are covered under a 90-day warranty or the remainder of the original one year manufacturer’s warranty from original date of purchase, whichever is greater.

Touchstone Home Products, Inc does not warrant its products against damage caused by third parties.

Touchstone Home Products, Inc does not cover damages caused by misuse, alterations, accident, lack of maintenance, abuse or neglect. Parts installed from other manufacturers will void this warranty.

The warranty does not cover paint scratches, cosmetic blemishes, dents, corrosion, or other normal wear and tear associated with the fireplace. Damage to fireplace or other components due to water, weather damage, long periods of dampness, condensation, damaging chemicals or cleaners are not covered under warranty.

This warranty does not cover breakage of fireplace glass panel.

Touchstone Home Products will not be responsible for installation, labor, or any other expenses related to the reinstallation of a warranted part, and such expenses are not covered under warranty.

Extended warranty coverage for the fireplace is available by contacting Touchstone Home Products, Inc.

directly at 1-800-215-1990.

30 Touchstone Home Products

Warranty

31800.215.1990 touchstonehomeproducts.com

Questions? We are here to help.

You can reach our team by phone, email or live chat. You may also fill out the contact form on our website and we will respond to your inquiry.

Visit our website or Touchstone Home Products YouTube Channel for detailed product support videos.

Showroom / Mailing Address:

TOUCHSTONE HOME PRODUCTS, INC.

208 Philips Road, Exton, PA 19341

Touchstone® TV Lift Cabinets

Visit our website to see the full Touchstone® product line.

Touchstone® TV Lift Mechanisms

FEB 2021

800.215.1990 sales@thpus.com touchstonehomeproducts.com

CALL US FIRST!

DO NOT RETURN TO STORE.

For immediate help with assembly, product information or if your product arrives damaged, call our toll free number or email us at customerservice@thpus.com.

Our staff is ready to provide assistance.

WARNING

Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury.

CAUTION

Keep this owner’s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product.