25051529-033 BOM.rtf

Order, For Internal Use Only

PRINTED 00/00/00 0:00 AM

file_0.png file_1.wmf

Order, For Internal Use Only

PRINTED 05/04/95 2:12 PM

Q2C Number: 25051529 Quote Number: 2 Revision Number: 0

Project Name: VA PHASE 4B Project Sub-Name:

Project Location: DES MOINES, IA

Q2C Number: 25051529 Quote Number: 2 Revision Number: 0 Project Name: VA PHASE 4B Quote Name:

Item No.

Qty.

Catalog Number / Details

033-00

Designation: 36th St.

METAL ENCLOSED SWITCHGEAR

METAL ENCLOSED SWITCHGEAR > 1000 VOLTS

GENERAL PRODUCT INFORMATION

PRODUCT TYPE: HVL

3 SECTION LINE-UP

INDOOR (Type1)

3 - 38.00 FEEDER SECTIONS

OVERALL DIMENSIONS: 114.00" 2896mm WIDE 90.00" 2286mm HIGH 72.50" 1842mm DEEP

APPROXIMATE WEIGHT: 4730 LBS 2150 KG

SWITCHGEAR RATINGS

SWITCHGEAR MAXIMUM VOLTAGE RATING: 15.0 KV

MAIN BUS: 1200A SILVER-PLATED COPPER

GROUND BUS: SILVER-PLATED COPPER

INSULATED BUS: HEAT SHRINK

BIL : 95 KV

INTEGRATED SHORT CIRCUIT CURRENT

RATINGS FOR SWITCHES WITH FUSES:

THE INTEGRATED SHORT CIRCUIT CURRENT

RATINGS FOR SWITCHES WITH FUSES

CAN BE FOUND IN THE INTEGRATED

RATINGS TABLES. REFER TO THE CATALOG

SECTIONS FOR EACH PRODUCT LINE.

NON-FUSED SWITCH RATINGS

MOMENTARY CURRENT: 40 KA ASYM (25 KA SYM)

FAULT CLOSE CURRENT: 40KA ASYM (25KA SYM)

SHORT TIME CURRENT 2 SEC:

25 KA SYM (40 KA ASYM)

SPECIFIC APPLICATION INFORMATION

NOMINAL SYSTEM VOLTAGE: 13200 VOLTS

SYSTEM GROUNDING: 3 WIRE WYE

SOLIDLY GROUNDED

FREQUENCY: 60 HZ

MAX AVAILABLE SHORT CKT CURRENT:

25KA SYM (40 KA ASYM)

FRONT AND REAR ACCESS

AMBIENT AIR TEMP: > -30C, <40 DEG C

STANDARD & OPTIONAL ITEMS COMMON TO LINEUP

EXTERIOR PAINT COLOR:

ANSI 61 LIGHT GREY

INSULATORS : GLASS POLYESTER

AC CONTROL POWER PROVIDED BY:

USER / CUSTOMER

STANDARD ENCLOSURE HARDWARE

APPLIES TO CATEGORY B APPLICATIONS

WHERE THE GENERAL PUBLIC WILL NOT

HAVE ACCESS TO THE SWITCHGEAR

SPACE HEATER INDOOR:

1200W-240VAC (300W-120VAC)

THERMOSTAT FOR HEATER(S)

PADLOCK PROVISIONS FOR UP TO 3

PADLOCKS ON SWITCH HANDLE CASTING

LABEL REQUIREMENTS : UL

STANDARDS: ANSI

DC CONTOL POWER PROVIDED BY SQUARE D

ON A SEPARATE LINE ITEM

CHARGING MOTOR/CLOSE VOLTAGE: 125 VDC

LUGS ARE BURNDY LONG BARREL

COMPRESSION TYPE VACL (AL / CU)

SPECIAL FEATURES OR TAG ITEMS (PER LINE-UP)

IF SPECIAL FEATURES ARE LISTED BELOW IN THIS

BILL OF MATERIAL, THEY WILL NOT APPEAR ON THE

FRONT ELEV OR ONE-LINE DRAWING AND MAY ALTER

THE FINAL LAYOUT AND DIMENSIONS.

IF UNKNOWN ANSWERS ARE LISTED BELOW

IN THIS BILL OF MATERIAL : DEFAULT

ASSUMPTIONS WERE MADE.

THESE ASSUMPTIONS MAY ALTER THE FINAL

PRICE, FINAL LAYOUT AND DIMENSIONS.

03 - Special Creme Paint per email

THIS HVL METAL-ENCLOSED SWITCHGEAR SHALL BE

DEPICTED IN THE ATTACHED DRAWINGS AND

SHALL INCLUDE THE FOLLOWING:

SECTION # 1, FEEDER -

Disconnect

1 - 15KV, 600A, 25KA HVL SWITCH Type1

MULTIPLE

600A CONTINUOUS & INTERRUPTING CURRENT

1 - MOTOR OPERATOR FOR HVL OTM MECHANISM

600/1200A

1 - HINGED REAR DOOR

1 - VERTICAL LINE/LOAD BARRIER WITH

PORCELAIN PASS THRUS

1 - Type1 BUS TRANSITION SECTION TO

MASTERCLAD SWITCHGEAR ON THE LEFT

1 - GROUND BAILS WITH GROUND STUDS, 3 PHASE

SET

1 - MIMIC BUS PAINTED DEVICE SYMBOLS

1 - SWITCH POSTION AUXILIARY CONTACTS 2NO-2NC

1 - KEY INTERLOCK SWITCH TO SECONDARY MAIN

BREAKER

1 - 3 PHASE SET OF #2 AWG AL/CU

COMPRESSION LUGS PER PHASE

LOADSIDE (UL LISTED)

- LOADSIDE, BOTTOM CABLE EXIT

3 - 15 KV (12.7 MCOV) DISTRIBUTION CLASS

SURGE ARRESTERS ON LINESIDE

SECTION # 2, FEEDER -

Disconnect

1 - 15KV, 600A, 25KA HVL SWITCH Type1

MULTIPLE

600A CONTINUOUS & INTERRUPTING CURRENT

1 - MOTOR OPERATOR FOR HVL OTM MECHANISM

600/1200A

1 - HINGED REAR DOOR

1 - VERTICAL LINE/LOAD BARRIER WITH

PORCELAIN PASS THRUS

1 - REAR CONNECTOR ASSEMBLY

1 - GROUND BAILS WITH GROUND STUDS, 3 PHASE

SET

1 - MIMIC BUS PAINTED DEVICE SYMBOLS

1 - SWITCH POSTION AUXILIARY CONTACTS 2NO-2NC

1 - KEY INTERLOCK SWITCH TO SECONDARY MAIN

BREAKER

1 - 3 PHASE SET OF #2 AWG AL/CU

COMPRESSION LUGS PER PHASE

LOADSIDE (UL LISTED)

- LOADSIDE, BOTTOM CABLE EXIT

3 - 15 KV (12.7 MCOV) DISTRIBUTION CLASS

SURGE ARRESTERS ON LINESIDE

SECTION # 3, FEEDER -

Disconnect

1 - 15KV, 600A, 25KA HVL SWITCH Type1

MULTIPLE

600A CONTINUOUS & INTERRUPTING CURRENT

1 - MOTOR OPERATOR FOR HVL OTM MECHANISM

600/1200A

3 - SQUARE D CURRENT LIMITING 15.5 KV 200E

FUSES

1 - HINGED REAR DOOR

1 - VERTICAL LINE/LOAD BARRIER WITH

PORCELAIN PASS THRUS

1 - REAR CONNECTOR ASSEMBLY

1 - GROUND BAILS WITH GROUND STUDS, 3 PHASE

SET

1 - MIMIC BUS PAINTED DEVICE SYMBOLS

1 - SWITCH POSTION AUXILIARY CONTACTS 2NO-2NC

1 - KEY INTERLOCK SWITCH TO SECONDARY MAIN

BREAKER

1 - 3 PHASE SET OF #2 AWG AL/CU

COMPRESSION LUGS PER PHASE

LOADSIDE (UL LISTED)

- LOADSIDE, BOTTOM CABLE EXIT

3 - 15 KV (12.7 MCOV) DISTRIBUTION CLASS

SURGE ARRESTERS ON LINESIDE

034-00

Designation: Douglas Ave.

METAL ENCLOSED SWITCHGEAR

METAL ENCLOSED SWITCHGEAR > 1000 VOLTS

GENERAL PRODUCT INFORMATION

PRODUCT TYPE: HVL

2 SECTION LINE-UP

INDOOR (Type1)

1 - 38.00 MAIN SECTION

1 - 38.00 UTILITY - COLD SEQUENCE METER

OVERALL DIMENSIONS: 76.00" 1930mm WIDE 90.00" 2286mm HIGH 54.50" 1384mm DEEP

APPROXIMATE WEIGHT: 3625 LBS 1648 KG

SWITCHGEAR MAXIMUM VOLTAGE RATING: 15.0 KV

MAIN BUS: 1200A SILVER-PLATED COPPER

GROUND BUS: SILVER-PLATED COPPER

MOMENTARY CURRENT: 40 KA ASYM (25 KA SYM)

FAULT CLOSE CURRENT: 40KA ASYM (25KA SYM)

SHORT TIME CURRENT 2 SEC:

25 KA SYM (40 KA ASYM)

SPECIFIC APPLICATION INFORMATION

NOMINAL SYSTEM VOLTAGE: 13200 VOLTS

SYSTEM GROUNDING: 3 WIRE WYE

SOLIDLY GROUNDED

FREQUENCY: 60 HZ

MAX AVAILABLE SHORT CKT CURRENT:

25KA SYM (40 KA ASYM)

FRONT AND REAR ACCESS

AMBIENT AIR TEMP: > -30C, <40 DEG C

STANDARD & OPTIONAL ITEMS COMMON TO LINEUP

EXTERIOR PAINT COLOR:

ANSI 61 LIGHT GREY

INSULATORS : GLASS POLYESTER

AC CONTROL POWER PROVIDED BY:

USER / CUSTOMER

STANDARD ENCLOSURE HARDWARE

APPLIES TO CATEGORY B APPLICATIONS

WHERE THE GENERAL PUBLIC WILL NOT

HAVE ACCESS TO THE SWITCHGEAR

SPACE HEATER INDOOR:

1200W-240VAC (300W-120VAC)

THERMOSTAT FOR HEATER(S)

PADLOCK PROVISIONS FOR UP TO 3

PADLOCKS ON SWITCH HANDLE CASTING

LABEL REQUIREMENTS : UL

STANDARDS: ANSI

DC CONTOL POWER PROVIDED BY SQUARE D

ON A SEPARATE LINE ITEM

CHARGING MOTOR/CLOSE VOLTAGE: 125 VDC

LUGS ARE BURNDY LONG BARREL

COMPRESSION TYPE VACL (AL / CU)

1 - THIS SWITCHGEAR IS CONNECTING TO

EXISTING EQUIPMENT

IF SPECIAL FEATURES ARE LISTED BELOW IN THIS

BILL OF MATERIAL, THEY WILL NOT APPEAR ON THE

FRONT ELEV OR ONE-LINE DRAWING AND MAY ALTER

THE FINAL LAYOUT AND DIMENSIONS.

IF UNKNOWN ANSWERS ARE LISTED BELOW

IN THIS BILL OF MATERIAL : DEFAULT

ASSUMPTIONS WERE MADE.

THESE ASSUMPTIONS MAY ALTER THE FINAL

PRICE, FINAL LAYOUT AND DIMENSIONS.

CAUTION: CONNECTION TO EXISTING

EQUIPMENT HAS BEEN SELECTED.

NO PRICING OR DRAWINGS FOR THIS CONNECTION

WILL BE INCLUDED IN THIS QUOTATION.

FIELD SERVICE

SHOULD TAKE ALL NECESSARY MEASUREMENTS FOR

CORRECT CONNECTION AND ALIGNMENT

PRICE WILL DEPEND ON THE RESULTS FROM

FIELD SERVICE

02 - Special Creme Paint per email

THIS HVL METAL-ENCLOSED SWITCHGEAR SHALL BE

DEPICTED IN THE ATTACHED DRAWINGS AND

SHALL INCLUDE THE FOLLOWING:

SECTION # 1, MAIN -

Disconnect

1 - 15KV, 600A, 25KA HVL SWITCH Type1

MULTIPLE

600A CONTINUOUS & INTERRUPTING CURRENT

1 - MOTOR OPERATOR FOR HVL OTM MECHANISM

600/1200A

1 - HINGED REAR DOOR

1 - VERTICAL LINE/LOAD BARRIER WITH

PORCELAIN PASS THRUS

1 - REAR CONNECTOR ASSEMBLY

1 - GROUND BAILS WITH GROUND STUDS, 3 PHASE

SET

1 - MIMIC BUS PAINTED DEVICE SYMBOLS

1 - SWITCH POSTION AUXILIARY CONTACTS 2NO-2NC

1 - KEY INTERLOCK SWITCH TO SECONDARY MAIN

BREAKER

1 - 3 PHASE SET OF 500 KCMIL AL/CU

COMPRESSION LUGS PER PHASE

LINESIDE (UL LISTED)

- LINESIDE, BOTTOM CABLE ENTRY

3 - 15 KV (12.7 MCOV) STATION CLASS SURGE

ARRESTERS ON LINESIDE

SECTION # 2, UTILITY - COLD SEQUENCE METER

Utility

1 - 15 KV Type1 UTILITY METERING SECTION

1 - PROVISIONS FOR BAR TYPE CTS

1 - MIMIC BUS PAINTED DEVICE SYMBOLS

01- Connection To MasterCclad 01- Install Utility Provided VTs & CTs

035-00

Designation: Douglas Ave.

Fully-Assembled MV MetalClad Swgr Metal Clad Switchgear > 1000 Volts

- - Consult Factory for Delivery - -

5 Section Line-up MASTERCLAD Switchgear Assembly Consisting of the following:

Network Communications Only RS485 Modbus Comms Wired Out Label Requirements: UL, for California Outdoor, Walk-in Single Aisle (Type 3R) With Front and Rear Access Rear Door Type 3R with Padlock Provisions

If Customer Witness Testing Required, must add in separately from this Bill of Material and price in at Standard Square D daily rate.

General Equipment Ratings Frequency: 60 Hertz Impulse Withstand Voltage (BIL): 95kV Maximum Bus Continuous Current: 1200A Maximum Short Circuit Current: 23kA (RMS Symmetrical) Maximum Voltage: 15kV Nominal System Voltage: 13.2kV, 3 Phase, 3 Wire, Ungrounded Delta One-Minute Withstand Voltage: 36kV RMS

General Structure Information 1200A Silver Plated Copper Main Bus Auxilary Control Power: Square D 120VAC Breaker Close Control Power: Square D Supplied 125VDC Breaker Trip Control Power: Square D Supplied 125VDC Bus Bracing: 23kA (RMS Symmetrical) Bus Supports: Epoxy (Std) Control Wiring: #12 AWG type SIS wire Current Circuit Wiring: #10 AWG type SIS wire Exterior Paint Color: ANSI #61, Light Gray (Std) Ground Bus: Copper, Unplated (Std) Lug Type: Supplied by Customer Screw Terminal Blocks, Insulated Square D LED Type lamps, (2) per cell 1 - 5th Wheel for Breaker 1 - Aisle Heater, up to 5kw 1 - Ammeter and Circuit Breaker for Strip Heater Circuit 1 - Fluorescent Battery Backed Emergency Lighting 1 - Humidistat for Space Heaters 1 - Mimic bus - painted device symbols (per cell) 1 - Padlock Hasps per Front Door 1 - Test Cabinet, 8 ft. cable 1 - Test Jumper, 14 ft. cable only 1 - Vent & Fan LV Panels Painted White

Dimensions:

Width of Lineup: 180.00" 4572mm Height @ Highest Point: 114.50" 2908mm Depth @ Base: 169.50 4305 mm Depth @ Roof: 178.50" 4534 mm Approximate Weight: 25104 lb 11411 kg

Special Features or TAG Items (per line-up) If Special Features are included in this Bill of Material, they will NOT appear on the Front-Elev or One-line Drawing and may alter the final layout and dimensions.

04 - Rear Door Assembly 05 - Special Creme Paint per email

Detailed Bill of Material

- - Consult Factory for Delivery - - This Metal Clad Switchgear shall be depicted in the attached drawing and shall including the following:

SECTION # 1, WORKSPACE -

1 - 72" Wide Blank Extension to Walk-in (Type 3R) w/Front Aisle 1 - Install HVL & UTILITY

SECTION # 2, UPPER, AUX. -

1 - VT Drawer with (3) VTs, (1) Primary Fuse per VT 1 - 15kVA, Single Phase CPT 1 - Insulating rear barrier over door-mounted components, (CA code/NEC)

SECTION # 2, LOWER, MAIN -

1 - 15kV Max. Voltage, 500MVA, 1200A, Vacuum Breaker Type: VR-15050-12 3 - Single Ratio 600:5 CT - Standard Accuracy - Model 780 - Set#4 1 - Breaker Control Switch 1t,1c (Std) 1 - Insulating rear barrier over door-mounted components, (CA code/NEC) 1 - Key Interlock (per key) Manufacturer :

Schneider 1 - MOC Switch Supplying 13 Additional Contacts (6a, 7b) 1 - TOC Switch Supplying 13 Additional Contacts (6a, 7b) 1 - Lockout Relay - 86-5 Deck 1 - Relay, 11, SEL, 351-7

SECTION # 3

1 - Special ATS

SECTION # 3, UPPER, AUX. -

1 - Blank Auxilary Cell (Upper) 1 - AC Control Power Transfer Scheme between two CPTs 1 - Insulating rear barrier over door-mounted components, (CA code/NEC)

SECTION # 3, LOWER, AUX. -

1 - VT Drawer with (3) VTs, (1) Primary Fuse per VT 1 - 15kVA, Single Phase CPT 1 - Insulating rear barrier over door-mounted components, (CA code/NEC)

SECTION # 4, WORKSPACE -

1 - 72" Wide Blank Extension to Walk-in (Type 3R) w/Front Aisle 2 - Install HVL

SECTION # 5, WORKSPACE -

1 - 72" Wide Blank Extension to Walk-in (Type 3R) w/Front Aisle 1 - DC Disconnect For Battery System 1 - Workspace Heater 1 - AC Loadcenter 1 - DC Loadcenter 1 - Eyewash System (Std w/ 72" Workspace & Provisions for Battery System) 1 - Change to 48" wide

035-01

C780 cable

035-02

C805Z020SSX0020

cable

035-03

2812MT

plug

035-04

ADDITIONAL TRUCK

035-05

9F60DMH005

FuseCL 15.5KV 5E EJO-1

035-06

4600319501

BUS BOOT MAIN CROSS BUS

035-07

9F60DMH005

FuseCL 15.5KV 5E EJO-1

036-00

Designation: Douglas Ave.

METAL ENCLOSED SWITCHGEAR

METAL ENCLOSED SWITCHGEAR > 1000 VOLTS

GENERAL PRODUCT INFORMATION

PRODUCT TYPE: HVL

2 SECTION LINE-UP

INDOOR (Type1)

2 - 38.00 FEEDER SECTIONS

OVERALL DIMENSIONS: 76.00" 1930mm WIDE 90.00" 2286mm HIGH 72.50" 1842mm DEEP

APPROXIMATE WEIGHT: 3020 LBS 1373 KG

SWITCHGEAR MAXIMUM VOLTAGE RATING: 15.0 KV

MAIN BUS: 1200A SILVER-PLATED COPPER

GROUND BUS: SILVER-PLATED COPPER

MOMENTARY CURRENT: 40 KA ASYM (25 KA SYM)

FAULT CLOSE CURRENT: 40KA ASYM (25KA SYM)

SHORT TIME CURRENT 2 SEC:

25 KA SYM (40 KA ASYM)

SPECIFIC APPLICATION INFORMATION

NOMINAL SYSTEM VOLTAGE: 13200 VOLTS

SYSTEM GROUNDING: 3 WIRE WYE

SOLIDLY GROUNDED

FREQUENCY: 60 HZ

MAX AVAILABLE SHORT CKT CURRENT:

25KA SYM (40 KA ASYM)

FRONT AND REAR ACCESS

AMBIENT AIR TEMP: > -30C, <40 DEG C

STANDARD & OPTIONAL ITEMS COMMON TO LINEUP

EXTERIOR PAINT COLOR:

ANSI 61 LIGHT GREY

INSULATORS : GLASS POLYESTER

AC CONTROL POWER PROVIDED BY:

USER / CUSTOMER

STANDARD ENCLOSURE HARDWARE

APPLIES TO CATEGORY B APPLICATIONS

WHERE THE GENERAL PUBLIC WILL NOT

HAVE ACCESS TO THE SWITCHGEAR

SPACE HEATER INDOOR:

1200W-240VAC (300W-120VAC)

THERMOSTAT FOR HEATER(S)

PADLOCK PROVISIONS FOR UP TO 3

PADLOCKS ON SWITCH HANDLE CASTING

LABEL REQUIREMENTS : UL

STANDARDS: ANSI

DC CONTOL POWER PROVIDED BY SQUARE D

ON A SEPARATE LINE ITEM

CHARGING MOTOR/CLOSE VOLTAGE: 125 VDC

LUGS ARE BURNDY LONG BARREL

COMPRESSION TYPE VACL (AL / CU)

IF SPECIAL FEATURES ARE LISTED BELOW IN THIS

BILL OF MATERIAL, THEY WILL NOT APPEAR ON THE

FRONT ELEV OR ONE-LINE DRAWING AND MAY ALTER

THE FINAL LAYOUT AND DIMENSIONS.

IF UNKNOWN ANSWERS ARE LISTED BELOW

IN THIS BILL OF MATERIAL : DEFAULT

ASSUMPTIONS WERE MADE.

THESE ASSUMPTIONS MAY ALTER THE FINAL

PRICE, FINAL LAYOUT AND DIMENSIONS.

02 - Special Creme Paint per email

THIS HVL METAL-ENCLOSED SWITCHGEAR SHALL BE

DEPICTED IN THE ATTACHED DRAWINGS AND

SHALL INCLUDE THE FOLLOWING:

SECTION # 1, FEEDER -

Disconnect

1 - 15KV, 600A, 25KA HVL SWITCH Type1

MULTIPLE

600A CONTINUOUS & INTERRUPTING CURRENT

1 - MOTOR OPERATOR FOR HVL OTM MECHANISM

600/1200A

1 - HINGED REAR DOOR

1 - VERTICAL LINE/LOAD BARRIER WITH

PORCELAIN PASS THRUS

1 - Type1 BUS TRANSITION SECTION TO

MASTERCLAD SWITCHGEAR ON THE LEFT

1 - GROUND BAILS WITH GROUND STUDS, 3 PHASE

SET

1 - MIMIC BUS PAINTED DEVICE SYMBOLS

1 - SWITCH POSTION AUXILIARY CONTACTS 2NO-2NC

1 - KEY INTERLOCK SWITCH TO SECONDARY MAIN

BREAKER

1 - 3 PHASE SET OF #2 AWG AL/CU

COMPRESSION LUGS PER PHASE

LOADSIDE (UL LISTED)

- LOADSIDE, BOTTOM CABLE EXIT

3 - 15 KV (12.7 MCOV) DISTRIBUTION CLASS

SURGE ARRESTERS ON LINESIDE

SECTION # 2, FEEDER -

Disconnect

1 - 15KV, 600A, 25KA HVL SWITCH Type1

MULTIPLE

600A CONTINUOUS & INTERRUPTING CURRENT

1 - MOTOR OPERATOR FOR HVL OTM MECHANISM

600/1200A

1 - HINGED REAR DOOR

1 - VERTICAL LINE/LOAD BARRIER WITH

PORCELAIN PASS THRUS

1 - REAR CONNECTOR ASSEMBLY

1 - GROUND BAILS WITH GROUND STUDS, 3 PHASE

SET

1 - MIMIC BUS PAINTED DEVICE SYMBOLS

1 - SWITCH POSTION AUXILIARY CONTACTS 2NO-2NC

1 - KEY INTERLOCK SWITCH TO SECONDARY MAIN

BREAKER

1 - 3 PHASE SET OF #2 AWG AL/CU

COMPRESSION LUGS PER PHASE

LOADSIDE (UL LISTED)

- LOADSIDE, BOTTOM CABLE EXIT

3 - 15 KV (12.7 MCOV) DISTRIBUTION CLASS

SURGE ARRESTERS ON LINESIDE

037-00

BATTERY SYSTEM

125Vdc 18Ah NiCad Varta Model RM18 (92 Cells) SGN 4-12 Zone 0 Open Rack AT10-130-006-0102000 Solid State Battery Charger USCS-5325 Spill Containment System

062-00

CANCLD

SQD SERVICE

Troubleshooting of MV Swgr