Att 10 DIVISION 01 _ GENERAL REQUIREMENTS.docx

DIVISION 01 – GENERAL REQUIREMENTS

01 45 00 – Quality Control

1. Construction inspections & testing

0. Tests, inspections, operational checks, documentation

0. PART 3 – Tests

1. Punch-out inspection

1. Contractor QC inspection + correction verification

1. PART 3 – Completion Inspection

1. Pre-final inspection

2. Government inspection prior to acceptance

2. PART 3 – Pre-Final Inspection

1. Final acceptance inspection

3. Required for project closeout

3. PART 3 – Final Acceptance Inspection

1. Special inspections

4. Code-required third-party inspections

4. PART 3 – Special Inspections

01 35 26 – Safety Requirements

1. Daily egress inspections

0. Daily inspection, weekly reporting

0. Fire Safety – Egress Routes

1. Weekly fire safety inspections

1. Entire work area

1. Fire Safety – Hazard Prevention

1. Monthly crane / LHE inspections

2. Documented inspections

2. Submittals – LHE Reports

01 57 19 – Temporary Environmental Controls

1. Daily environmental compliance inspections

0. Logs + corrective actions

0. Quality Control

1. Post-storm inspections

1. Sediment basins, erosion controls

1. Protection of Resources

1. Environmental monitoring

2. Air, water, noise per monitoring plan

2. Submittals

01 74 19 – Construction Waste Management

1. Pre-work site assessment

0. Waste stream evaluation

0. Quality Assurance

1. Daily waste management inspections

1. Ongoing monitoring & documentation

1. Quality Assurance

01 81 13 – Sustainable Construction

1. Periodic sustainability inspections

0. Reviewed during job conferences

0. Quality Assurance

01 91 00 – General Commissioning

1. Installation inspections

0. System accessibility & compliance

0. Commissioning Description

1. Site observation visits

1. CxA inspections during construction

1. Definitions

1. Pre-functional inspections

2. Before functional testing

2. Definitions

1. Warranty phase inspections

3. Post-occupancy inspections

3. Definitions

1. Maintenance documentation

4. O&M manuals incl. inspection & PM procedures

4. Training & Documentation

DIVISION 02–33 – SITE & UTILITIES

02 41 00 – Demolition

1. Pre-demolition site survey

0. Inspection of existing conditions

0. Part 1 – Protection

1. Daily safety & protection inspections

1. Barricades, fencing, fire protection

1. Part 1 – Protection

1. Post-demolition cleanup inspection

2. Resident Engineer approval

2. Part 3 – Cleanup

21 08 00 – Commissioning of Fire Suppression Systems

1. Construction inspections

0. Continuous inspection during installation

0. Part 3 – Construction Inspections

1. Pre-functional inspections

1. Checklist-based verification

1. Part 3 – Pre-Functional Checklists

1. Functional performance testing

2. Witnessed testing

2. Part 3 – Systems Functional Performance Testing

1. Maintenance training

3. O&M staff training

3. Part 3 – Training

22 11 00 – Facility Water Distribution

1. Hydrostatic inspections

0. Pressure testing prior to concealment

0. Part 3 – Tests

1. Sterilization inspections

1. Post-test disinfection verification

1. Part 3 – Sterilization

1. As-built inspection documentation

2. Required before final acceptance

2. As-Built Documentation

1. Maintenance documentation

3. O&M manuals with inspection procedures

3. Submittals

31 20 00 – Earthwork

1. Geotechnical inspections

0. Continuous excavation inspections by Geotech

0. Part 3 – Excavation

1. Subgrade inspections

1. Approval before placement of work

1. Part 3 – Excavation Drainage

1. Compaction testing

2. Density testing per ASTM

2. Part 3 – Filling and Backfilling

32 05 23 – Cement & Concrete for Exterior Improvements

1. Pre-installation inspections

0. Subgrade & forms verification

0. Execution – Preparation

1. Field testing

1. Concrete, subbase testing

1. Quality Assurance

1. Curing inspections

2. Minimum 7-day curing verification

2. Concrete Curing

32 12 16 – Asphalt Paving

1. Plant & equipment inspections

0. Resident Engineer access

0. Section 1.3

1. Proof-rolling inspections

1. Subgrade verification

1. Part 3 – Subgrade

1. Rolling & compaction inspections

2. Course-by-course approval

2. Part 3 – Execution

32 17 23 – Pavement Markings

1. Surface inspection prior to marking

0. COR approval required

0. Preparation

1. Post-installation inspection

1. Alignment, thickness, coverage

1. Paint Application

1. Maintenance / repair

2. Replace deficient markings

2. Protection & Cleaning

33 08 00 – Commissioning of Site Utility Systems

1. Construction inspections

0. Continuous site utility inspections

0. Part 3 – Construction Inspections

1. Pre-functional inspections

1. Checklist verification

1. Part 3 – Pre-Functional Checklists

1. Functional testing

2. Witnessed testing

2. Part 3 – Systems Functional Performance Testing

1. Maintenance training

3. Owner O&M staff

3. Part 3 – Training

33 10 00 – Water Utilities

1. Hydrostatic pressure inspections

0. 1.5× working pressure

0. Field Quality Control

1. Video inspection

1. Entire pipeline prior to acceptance

1. Field Quality Control

1. Disinfection inspection

2. Chlorination verification

2. Execution – Disinfection

1. Maintenance access inspections

3. Backflow preventers, valves, hydrants

3. Execution – Backflow Preventers