Attachment 4 - RW_TDS_KTC_HS.pdf

GENERAL PRODUCT INFORMATION

Colors: Clear Solids Volume: 92%

V.O.C.: 94 g/l

Pot-life: 30-Minutes @ 72° F and 50% RH

Mix-Ratio: 1-Part A to 1-Part B by volume.

Cure Schedule: 72° F @ 50% R.H.

To touch: 1-2-Hours To re-coat: 2-Hours Minimum

24-Hours Maximum Foot Traffic: 3-5-Hours Heavy Traffic: 12-Hours

Clean-up: Acetone / MEK Application Temp: 30ºF(-1.1ºC) - 90ºF(32.2ºC) SLOW-SET: Approximately 20%-30% extended working time*

GENERAL PRODUCT PERFORMANCE

TEST TYPE TEST METHOD RESULT

Hardness

ASTM D-2240

Shore D 83

Taber Abrasion ASTM-D-4060 35 mg loss

Tensile Strength ASTM C-307 3,400 psi

Flammability ASTM D 635 Self extinguishing

Impact Resistance ASTM D 2794 160 lb

Flexibility 1/4” cylindrical mandrel ASTMD 522 Pass

Adhesion ASTMD-4541 500+ PSI concrete fracture

USES:

» Commercial & Industrial

Flooring » Primer, Mid and Topcoat » Urethane Mortar Topcoats » FDA/CFSAN compliant

ADVANTAGES:

» Low VOC » Reasonable working time » 1-2 hour walk-on time » High abrasion resistance » UV Stable

PACKAGING & SHELF-LIFE

Kinetic HS is available in the following kits:

» 10-gallon kit (5-gal part A and 5-gal part B)

Shelf-Life::

» 24 months factory sealed and stored at room temperature.

ANCILLARY PRODUCTS:

» May be used in conjunction with all Resinwerks™ materials » For pigmented coatings, post-add Resinwerks Urethane

Pigments at 12-oz per gallon.

SUGGESTED APPLICATION:

» Concrete Primer: Apply to properly profiled concrete.

» Broadcast Coat: Broadcast Quartz or Chip media into wet film

» Grout Coat: Apply over chip, quartz or sand broadcast

» Top-Coat: Apply over existing epoxy or polyaspartic coating

MATERIAL COVERAGE

DRY FILM

THICKNESS

APPROXIMATE

COVERAGE

APPROXIMATE

KIT COVERAGE

6 mils dft 240 ft2 / gallon (5.9m™/L)

1,440 ft2 / gallon (35.2m™/L)

8 mils dft 185 ft2 / gallon (4.5m™/L)

1,110 ft2 / gallon (27.1m™/L)

10 mils dft 145 ft2 / gallon (3.5m™/L)

870 ft2 / gallon (21.3m™/L)

KINETIC HS IS A HIGH SOLIDS FAST-CURING ALIPHATIC POLYASPARTIC POLYUREA

DESIGNED FOR HEAVY-TRAFFIC APPLICATIONS. Kinetic HS provides highly durable film qualities with minimal installation odor. It offers good high-solids polyaspartic working times and serves as an excellent primer, grout or top-coat in rapid return to service applications. This non-yellowing formulation also offers superior abrasion and chemical resistance. It is fully USDA and FDA compliant as per FDA/CFSAN US Food Code 6.101.11 Surface Characteristics. Kinetic HS is available in a clear gloss finish and all standard and safety colors and may be fortified with silver-ion pigments to inhibit microbial growth in food & beverage, medical, and other settings.

ALSO AVAILABLE IN A SLOW-SET VERSION: see General Product Information for cure schedule.

KINETIC HS®

TECHNICAL DATA SHEET

RESINWERKS, LLC

7205 GILPIN WAY, SUITE 200

DENVER, CO 80229

SURFACE PREPARATION

Ensure substrate to be coated is clean, dry, and in sound condition.

All laitance, curing compounds, concrete hardeners, and other surface contaminants must be removed. Prepare concrete in accordance with ASTM D 4259-83. Mechanical shot blasting or grinding is recommended to achieve a surface profile of ICRI CSP 2-3. Surface to be coated must be completely porous and free of excessive dust & contaminants.

MOISTURE IN CONCRETE

Concrete slabs should be tested prior to application for elevated moisture vapor emission levels. Resinwerks recommends ASTM F2170-19 standard for determining relative humidity in concrete slabs using RH probes. For slabs exhibiting elevated moisture levels in excess of 75% RH, Resinwerks Vapor Barrier Epoxy should be substituted as a primer. For more information, please contact your Resinwerks technical representative.

DE-GREASING OF CONTAMINATED SUBSTRATES

For concrete substrates containing oil, animal fats, or other carbon based contaminants, slabs should be de-greased appropriately using an enzymatic based concrete de-greasing agent. Multiple applications may be required depending on the level of contamination. For more information, please contact your Resinwerks technical representative. .

TREATMENT OF JOINTS & CRACKS

Prior to installation of any Resinwerks primer, all joints, cracks and other substrate irregularities must be addressed.

For more information on specific joint treatment procedures, please contact your Resinwerks technical services representative.

MIXING INSTRUCTIONS:

» Prior to mixing, all products should be properly acclimated to the local ambient room temperature of 40ºF(4.4ºC) - 85ºF (29.4ºC).

» Mix 1-part A to 1-Part B by volume for two minutes using a slow speed jiffy mixer.

» If pigmenting with Resinwerks Universal Pigments, add at a rate of 10-12 oz per mixed gallon or 1-quart per 3-gallon mix.

» *Slow-Set part A offers extended working times. Cure schedule is dependent on ambient temperature and humidity.

APPLICATION INSTRUCTIONS

» Immediately following mixing, pour onto substrate in a uniform ribbon and spread evenly with a squeegee or seal-coat broom.

Immediately back-roll in a direction perpendicular to your initial ribbon with a 3/8” nap roller. Working time and cure schedule will be dependent on ambient temperature and humidity.

Material will be dry to the touch and ready for subsequent coats within approximately 2-3-hours following application. Contact Resinwerks directly for additional application specifics.

LIMITATIONS

» Do not apply over concrete experiencing ASR » Do not apply over Acrylics or MMA Coatings » Do not apply over existing coatings / sealers that have not been properly abraded and cleaned.

» D not apply to new slabs < 28-days old » Do not apply over areas wiped with denatured alcohols » Do not apply to concrete < 3500 PSI compression strength » Do not apply product when ambient or room temperature is below 32ºF (0ºC) or over 90ºF(32.2ºC) or if the relative ambient humidity is above 85%.

» This product is not recommended for immersion service.

» DEW POINT: Do not apply when dew point is within 5ºF of the ambient temperature.

MAINTENANCE

The long-term performance, appearance, and life expectancy of wear surface products are dependent on an adequate routine maintenance program designed specifically for the installed wear surface. Resinous floor coating systems are nonporous, causing dirt and contaminants to remain on the surface. Recommended maintenance programs consist of frequent and thorough cleaning utilizing a neutral PH cleaner. The frequency of washing will vary depending on floor usage type, traffic and age. Please contact your local Resinwerks technical representative for more information.

NOTES

Thoroughly read all Material Safety Data Sheets prior to use and maintain copies on job-site at all times.

Mock-ups and field test areas are strongly recommended in order to validate performance and appearance related characteristics (including but not limited to color, inherent surface variations, wear, anti dusting, abrasion resistance, chemical resistance, stain resistance, coefficient of friction, etc.) to ensure system performance as specified for the intended use, and to determine approval of the coating system.

Variability in job site conditions (including but not limited to surface preparation, sunlight, humidity, dew point, temperature, etc.) during application of Urethane products may lead to fish-eyes, blistering, pinholes, wrinkling, or out-gassing of air in the concrete and are not product defects.

TECHNICAL ASSISTANCE

PHONE: 720-484-5160 WEB: www.resinwerks.com

10-Gal Kit SKUs: 214-0000-10, 214-slow-10 2-Gal Kit SKUs: 214-0000-02, 214-slow-02KINETIC HS®

TECHNICAL DATA SHEET