36C25622R0094 081400 Interior Wood Doors .docx

REPLACE AHU #104 AND DUCTWORK BLDG. 7

DEPARTMENT OF VETERANS AFFAIRS HEALTH CARE SYSTEM-ALEXANDRIA, LA

PROJECT NO.: 502-19-107

SECTION 08 14 00

INTERIOR WOOD DOORS

GENERAL

SUMMARY

Section Includes:

Interior flush wood doors transparent finish.

RELATED WORK

Section 01 81 13, SUSTAINABLE CONSTRUCTION REQUIREMENTS: Paints and Coatings and Composite Wood and Agrifiber VOC Limits.

Section 08 71 00, DOOR HARDWARE: Door Hardware including hardware location (height).

Section 08 11 13, HOLLOW METAL DOORS AND FRAMES: Installation of Doors.

Section 08 71 00, DOOR HARDWARE: Installation of Door Hardware.

Section 09 06 00, SCHEDULE FOR FINISHES: Door Finish.

APPLICABLE PUBLICATIONS

Comply with references to extent specified in this section.

American National Standards Institute/Window and Door Manufacturers Association (ANSI/WDMA):

I.S. 1A13 - Architectural Wood Flush Doors.

ASTM International (ASTM):

E9009(2016) - Laboratory Measurements of Airborne Sound Transmission Loss of Building Partitions and Elements.

Window and Door Manufacturers Association (WDMA):

TM 714 - CycleSlam Test.

TM 814 - Hinge Loading Test.

TM 1014 - Screw Holding Capacity.

SUBMITTALS

Submittal Procedures: Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES.

Submittal Drawings:

Show size, configuration, and fabrication and installation details.

Indicate project specific requirements not included in Manufacturer's Literature and Data submittal.

Manufacturer's Literature and Data:

Description of each product.

Samples:

Corner section of flush veneered door 300 mm (12 inches) square, showing details of construction, labeled to show grade and type number and conformance to specified standard.

Veneer sample 200 mm by 275 mm (8 inch by 11 inch) showing specified wood species sanded to receive a transparent finish. Factory finish veneer sample where the prefinished option is accepted.

Sustainable Construction Submittals:

Low PollutantEmitting Materials:

Show volatile organic compound types and quantities.

Test Reports: Indicate products comply with specifications.

Screw Holding Capacity Test.

CycleSlam Test.

HingeLoading Test.

Operation and Maintenance Data:

Care instructions for each exposed finish product.

QUALITY ASSURANCE

Manufacturer Qualifications:

Regularly and presently manufactures specified products.

Manufactures specified products with satisfactory service on five similar installations for minimum five years.

DELIVERY

Deliver products in manufacturer's original sealed packaging.

Minimum 0.15 mm (6 mil) polyethylene bags or cardboard packaging to remain unbroken during delivery and storage.

Mark packaging, legibly. Indicate manufacturer's name or brand, type, color, and manufacture date.

Identify door opening corresponding to Door Schedule.

Before installation, return or dispose of products within distorted, damaged, or opened packaging. Retain packaging for door protection after installation.

STORAGE AND HANDLING

Store products indoors in dry, weathertight conditioned facility.

Store doors according to ANSI/WDMA I.S. 1A.

Protect products from damage during handling and construction operations.

FIELD CONDITIONS

Environment:

Product Temperature: Minimum 21 degrees C (70 degrees F) for minimum 48 hours before installation.

Work Area Ambient Temperature Range: 21 to 27 degrees C (70 to 80 degrees F) continuously, beginning 48 hours before installation.

Comply with door manufacturer's instructions for relative humidity.

WARRANTY

Construction Warranty: FAR clause 52.24621, "Warranty of Construction."

Manufacturer's Warranty: Warrant interior factory finished flush wood doors against material and manufacturing defects.

Warranty Period: Lifetime of original installation.

PRODUCTS

PRODUCTS - GENERAL

Basis of Design: Section 09 06 00, SCHEDULE FOR FINISHES.

Provide each product from one manufacturer.

Sustainable Construction Requirements:

Low PollutantEmitting Materials: Comply with VOC limits specified in Section 01 81 13, SUSTAINABLE CONSTRUCTION REQUIREMENTS for the following products:

Paints and coatings.

Composite wood and agrifiber.

FLUSH WOOD DOORS

General:

ANSI/WDMA I.S. 1A, Extra Heavy Duty.

Adhesive: Type II.

Core: Structural composite lumber, except when mineral core is required for fire rating.

Thickness: 44 mm (13/4 inches) unless otherwise shown or specified.

Faces:

ANSI/WDMA I.S. 1A.

One species throughout project unless scheduled or otherwise shown.

Transparent Finished Faces: Premium Grade. rotary cut, white maple .

A Grade face veneer.

Match face veneers for doors for uniform effect of color and grain at joints.

Door Edges: Same species as door face veneer, except maple is acceptable for stile face veneer on birch doors.

In existing buildings, where doors are required to have transparent finish, use wood species, grade, and assembly of face veneers to match adjacent existing doors.

Painted Finishes: Custom Grade, mill option close grained hardwood, premium or medium density overlay.

Factory sand doors for finishing.

Wood For Stops, Louvers, Muntins and Moldings for Flush Doors Required to Have Transparent Finish:

Solid wood of same species as face veneer, except maple is acceptable on birch doors.

FABRICATION

Factory machine interior wood doors to receive hardware, bevels, undercuts, cutouts, accessories, and fitting for frame.

Rout doors for hardware using templates and location heights specified in Section 08 71 00, DOOR HARDWARE.

Factory fit doors to frame, bevel lock edge of doors 3 mm (1/8 inch) for each 50 mm (2 inches) of door thickness.

Clearances between Doors and Frames and Floors:

Door Jambs, Heads, and Meeting Stiles: Maximum 3 mm (1/8 inch).

Finish surfaces, including both faces, top and bottom and edges of the doors smooth to touch.

Identify each door on top edge.

Mark with stamp, brand or other indelible mark, giving manufacturer’s name, door’s trade name, construction of door, date of manufacture and quality.

Mark door or provide separate certification including name of inspection organization.

Identify door manufacturing standard, including glue type.

Identify veneer and quality certification.

FINISHES

Field Finished Doors: Seal top and bottom edges of doors with two coats of catalyzed polyurethane or water-resistant sealer.

Factory Transparent Finish:

Factory finish flush wood doors.

ANSI/WDMA I.S. 1A Section F3 Finish System Descriptions for System 5, Conversion Varnish or System 7, Catalyzed Vinyl.

Use stain when required to produce finish specified in Section 09 06 00, SCHEDULE FOR FINISHES.

EXECUTION

PREPARATION

Examine and verify substrate suitability for product installation.

Verify door frames are properly anchored.

Verify door frames are plumb, square, in plane, and within tolerances for door installation.

Protect existing construction and completed work from damage.

INSTALLATION

Install products according to manufacturer's instructions and approved submittal drawings.

When manufacturer's instructions deviate from specifications, submit proposed resolution for Contracting Officer's Representative consideration.

PROTECTION

After installation, place shipping container over door and tape in place.

Do not apply tape to door faces and edges.

Provide protective covering over exposed hardware in addition to covering door.

Maintain covering in good condition until removal is directed by Contracting Officer's Representative.

- E N D -

08 14 00 - 1