36C25220B0010-012.pdf

13100 watertown plank road suite 200 elm grove, wi 53122

Nagel Architects Project Number: 150401

Kahler Slater, Inc.

44 E. Mifflin Street

Madison, WI 53703

Ring & DuChateau, LLP

17400 W. Capitol Drive

Brookfield, WI 53045

Environmental Management Consulting, Inc.

W7748 County Highway V

Lake Mills, WI 53551

The Concord Group

55 E. Monroe Street

Suite 2850

Chicago, IL 60603

AutoCAD SHX Text

%%UGENERAL NOTES

AutoCAD SHX Text

1. LEGEND IS A STANDARD LEGEND. NOT ALL SYMBOLS AND

AutoCAD SHX Text

ABBREVIATIONS SHOWN MAY BE USED ON THIS PROJECT.

AutoCAD SHX Text

2. FOR LOCATIONS AND SIZES OF WALL OPENINGS SEE ARCHITECTURAL

AutoCAD SHX Text

DRAWINGS.

AutoCAD SHX Text

3. INSTALLATION SHALL PROVIDE READY ACCESS TO VALVES, DAMPERS,

AutoCAD SHX Text

COILS, AIR FILTERS, AIR FLOW MEASURING STATIONS, AND OTHER

AutoCAD SHX Text

DEVICES. ACCESS DOORS SHALL BE INSTALLED TO PROVIDE ADEQUATE

AutoCAD SHX Text

CLEARANCES FOR DIRECT ACCESS.

AutoCAD SHX Text

4. DESIGNATE A PERSON TO BE RESPONSIBLE FOR FIRE WATCH DURING

AutoCAD SHX Text

WELDING AND CUTTING OPERATIONS. PERSON PERFORMING FIRE WATCH

AutoCAD SHX Text

DUTIES SHALL NOT BE SAME INDIVIDUAL THAT IS PERFORMING WELDING

AutoCAD SHX Text

OPERATIONS. COMPLY WITH OSHA STANDARDS FOR WELDING. PROVIDE

AutoCAD SHX Text

TEMPORARY FIRE EXTINGUISHERS DURING CONSTRUCTION.

AutoCAD SHX Text

5. PROVIDE LOCAL MECHANICAL VENTILATION DURING WELDING, AND A

AutoCAD SHX Text

DUCT TO OUTSIDE.

AutoCAD SHX Text

6. DUCT DIMENSIONS ARE CLEAR INSIDE DIMENSIONS. THE FIRST FIGURE

AutoCAD SHX Text

OF DUCT SIZE INDICATES DIMENSION OF FACE SHOWN OR INDICATED.

AutoCAD SHX Text

7. EQUIPMENT SHALL BE INSTALLED PER MANUFACTURER'S

AutoCAD SHX Text

RECOMMENDATIONS AND INSTRUCTIONS.

AutoCAD SHX Text

8. LOCATIONS, SIZES, CLEARANCES AND CONFIGURATIONS OF EQUIPMENT

AutoCAD SHX Text

SHOWN ARE BASED ON SPECIFIC SCHEDULED MANUFACTURERS AND

AutoCAD SHX Text

MODEL NUMBERS. SUBSTITUTION OF SUCH EQUIPMENT MANUFACTURERS

AutoCAD SHX Text

WILL REQUIRE THE CONTRACTORS PRIOR VERIFICATION OF CONFORMANCE

AutoCAD SHX Text

PER THE REQUIREMENTS OF LOCATION, SIZE CLEARANCES AND

AutoCAD SHX Text

CONFIGURATION AS COMPARED TO SPACE ALLOCATED TO HOUSE

AutoCAD SHX Text

SPECIFIC EQUIPMENT.

AutoCAD SHX Text

9. SUPPLY AND RETURN AIR DUCTWORK SHALL BE CONSTRUCTED,

AutoCAD SHX Text

INSTALLED, AND INSULATED AS SPECIFIED; INSPECT DUCTWORK,

AutoCAD SHX Text

SUPPORTS AND INSULATION FOR DAMAGE OR FAULTY INSTALLATION.

AutoCAD SHX Text

REPLACE, OR REPAIR AS REQUIRED SO THAT FINAL INSTALLATION IS

AutoCAD SHX Text

ADEQUATELY SEALED FROM LEAKS, FREE OF DEFECTS, AND IN

AutoCAD SHX Text

ACCORDANCE WITH SPECIFICATIONS.

AutoCAD SHX Text

10. WHERE FLEXIBLE DUCTWORK IS USED, MAXIMUM ALLOWABLE LENGTH

AutoCAD SHX Text

SHALL BE 5 FEET.

AutoCAD SHX Text

11. ACOUSTICAL DUCT LINER IS NOT PERMITTED ON THIS PROJECT.

AutoCAD SHX Text

12. NEW CONTROLS TO BE COMPATIBLE WITH EXISTING DDC SYSTEM AT

AutoCAD SHX Text

THE FACILITY.

AutoCAD SHX Text

13. ONE THERMOSTAT PER FAN COIL UNLESS OTHERWISE NOTED. WHERE

AutoCAD SHX Text

MULTIPLE THERMOSTATS ARE NOTED AND THOSE ROOMS ARE SERVED BY

AutoCAD SHX Text

ONE FAN COIL UNIT, THAT THERMOSTAT SHALL BE AN AVERAGING

AutoCAD SHX Text

THERMOSTAT AND THE FAN COIL UNIT SHALL RESPOND TO AN AVERAGE

AutoCAD SHX Text

CONDITION.

AutoCAD SHX Text

14. ALL PIPING AND DUCTS IN FINISHED ROOMS OR SPACES SHALL BE

AutoCAD SHX Text

CONCEALED IN A FURRED CHASE OR ABOVE THE SUSPENDED CEILING.

AutoCAD SHX Text

15. TOTAL STATIC PRESSURE NOTED IN THE SCHEDULES INCLUDES DUCT

AutoCAD SHX Text

SYSTEM, TERMINAL UNITS, FILTERS, COILS, ETC.

AutoCAD SHX Text

16. FOR TYPICAL STEAM AND WATER PIPING CONNECTIONS TO EQUIPMENT,

AutoCAD SHX Text

SEE STANDARD EQUIPMENT DETAILS.

AutoCAD SHX Text

17. WATER PIPE CONNECTIONS TO AIR HEATING AND COOLING COILS SHALL

AutoCAD SHX Text

BE MADE TO PROVIDE COUNTER FLOW BETWEEN WATER AND AIR.

AutoCAD SHX Text

18. REFER TO ARCHITECTURAL REFLECTED CEILING PLANS FOR EXACT

AutoCAD SHX Text

LOCATIONS OF CEILING DIFFUSERS, REGISTERS, AND GRILLES.

AutoCAD SHX Text

19. SEISMIC PROVISIONS REQUIRED - SEE SPECS

AutoCAD SHX Text

20. ALL PRESSURES LISTED ARE GAGE PRESSURE UNLESS OTHERWISE

AutoCAD SHX Text

NOTED.

AutoCAD SHX Text

21. PROJECT AREA HAS ASBESTOS CONTAINING MATERIALS. AREA TO BE

AutoCAD SHX Text

ABATED PRIOR TO ANY DEMOLITION OR NEW WORK BEING PERFORMED.

AutoCAD SHX Text

SEE SHEET HA100 FOR MORE INFORMATION.

AutoCAD SHX Text

ABBREVIATIONS

AutoCAD SHX Text D DAMPER - AUTOMATIC DAMPER - AUTOMATIC D-1 OUTDOOR AIR DAMPER OUTDOOR AIR DAMPER D-2 RETURN AIR DAMPER RETURN AIR DAMPER D-3 RELIEF AIR DAMPER RELIEF AIR DAMPER DB DECIBELS DECIBELS Db DRY-BULB TEMPERATURE DRY-BULB TEMPERATURE DD-1 DESIGN DEVELOPMENT (SUBMISSION1) DD-2 DESIGN DEVELOPMENT (SUBMISSION2) DDC DIRECT DIGITAL CONTROLS DIRECT DIGITAL CONTROLS DEG DEGREE DEGREE DF DIFFUSER DIFFUSER DIA DIAMETER DIAMETER DIW DEIONIZED WATER DEIONIZED WATER DP DEW POINT TEMPERATURE DEW POINT TEMPERATURE DP DIFFUSER PLATE DIFFUSER PLATE DPA DIFFERENTIAL PRESSURE ASSEMBLY DIFFERENTIAL PRESSURE ASSEMBLY DPS DIFFERENTIAL PRESSURE SENSOR DIFFERENTIAL PRESSURE SENSOR DX DIRECT EXPANSION DIRECT EXPANSION DXCC DIRECT EXPANSION COOLING COIL

AutoCAD SHX Text CD-2 CONSTRUCTION DOCUMENTS (SUBMISSION2) CDR STEAM CONDENSATE RETURN STEAM CONDENSATE RETURN CENT CENTRIFICAL CFH CUBIC FEET PER HOUR CUBIC FEET PER HOUR CFM CUBIC FEET PER MINUTE CUBIC FEET PER MINUTE CFT CUBIC FEET CUBIC FEET CFP CHEMICAL FEED PUMP CHEMICAL FEED PUMP CG CEILING GRILLE CEILING GRILLE CH CHILLER CHILLER CHP CHILLED WATER PUMP CHILLED WATER PUMP CHW CHILLER WATER CHILLER WATER CHR CHILLED WATER RETURN CHS CHILLED WATER SUPPLY CI CAST IRON CAST IRON CM CARBON MONOXIDE CARBON MONOXIDE CM CUBIC METER CUBIC METER CM/S CUBIC METER PER SECOND CO CLEAN OUT CLEAN OUT CO2 CARBON DIOXODE CARBON DIOXODE COMP COMPRESSOR UNIT COP COEFFICIENT OF PERFORMANCE COEFFICIENT OF PERFORMANCE CP CONDENSATE PUMP CONDENSATE PUMP CR CEILING REGISTER CEILING REGISTER CS CONDENSATE STORAGE TANK CONDENSATE STORAGE TANK CSG CLEAN STEAM GENERATOR CLEAN STEAM GENERATOR CT COOLING TOWER COOLING TOWER CU CONDENSING UNIT CONDENSING UNIT CUH CABINET UNIT HEATER CABINET UNIT HEATER CV CONSTANT VOLUME CONSTANT VOLUME CW COLD WATER (POTABLE) COLD WATER (POTABLE) CWCC CHILLED WATER COOLING COIL CWP CONDENSER WATER PUMP CONDENSER WATER PUMP CWR CONDENSER WATER RETURN (TO CONDENSER WATER RETURN (TO COOLING TOWER) CWS CONDENSER WATER SUPPLY CONDENSER WATER SUPPLY (FROM COOLING TOWER)

AutoCAD SHX Text B BOILER BOILER BD BUTTERFLY DAMPER BUTTERFLY DAMPER BDD BACKDRAFT DAMPER BACKDRAFT DAMPER BDR BASE BOARD RADIATOR BASE BOARD RADIATOR BFP BACKFLOW PREVENTER BACKFLOW PREVENTER BFT BOILER PLANT FIRE TUBE BG BOTTOM GRILLE BOTTOM GRILLE BHP BRAKE HORSEPOWER BRAKE HORSEPOWER BHW HOT WATER HEATING BOILER HOT WATER HEATING BOILER BHX BOILER BLOWDOWN HEAT EXCHANGER BIW BACKWARD INCLINED WHEEL (FAN) BACKWARD INCLINED WHEEL (FAN) BMT BONE MARROW TRANSPLANT BONE MARROW TRANSPLANT BR BOTTOM REGISTER BOTTOM REGISTER BSC BIOLOGICAL SAFETY CABINETS BIOLOGICAL SAFETY CABINETS BT BLOWOFF TANK BLOWOFF TANK BTC BLOWOFF TANK CONTROL VALVE BTU BRITISH THERMAL UNIT BRITISH THERMAL UNIT BTUH BRITISH THERMAL UNIT PER HOUR BWT BOILER PLANT WATER TUBE

AutoCAD SHX Text A/E ARCHITECT / ENGINEER ARCHITECT / ENGINEER AAHX AIR TO AIR HEAT EXCHANGER AB AIR BLENDER AIR BLENDER AAV AUTOMATIC AIR VENT AUTOMATIC AIR VENT ACC AIR COOLED CONDENSER AIR COOLED CONDENSER ACCH AIR COOLED CHILLER AIR COOLED CHILLER ACCU AIR-COOLED CONDENSING UNIT AIR-COOLED CONDENSING UNIT ACU AIR CONDITIONING UNIT AIR CONDITIONING UNIT ACD AUTOMATIC CONTROL AUTOMATIC CONTROL DAMPER,MODULATING ACD-TP AUTOMATIC CONTROL DAMPER,TWO POSITION AD ACCESS DOOR ACCESS DOOR AF AFTER FILTER AFTER FILTER AFCV AIR FLOW CONTROL VALVE AFF ABOVE FINISHED FLOOR ABOVE FINISHED FLOOR AFMD AIR FLOW MEASURING DEVICE AIR FLOW MEASURING DEVICE AFW AIR FOIL WHEEL (FAN) AHU AIR-HANDLING UNIT AIR-HANDLING UNIT AMP AMPERGE AMPERGE AP ACCESS PANEL ACCESS PANEL APD AIR PRESSURE DROP AIR PRESSURE DROP ARI AIR CONDITIONING AND AIR CONDITIONING AND REFRIGERATION INSTITUTE AS AIR SEPARATOR AIR SEPARATOR ASME AMERICAN SOCIETY OF MECHANICAL ENGINEERS AW AIR WASHER AIR WASHER AXF AXIAL FLOW AXIAL FLOW

AutoCAD SHX Text C CENTIGRADE (CELCIUS) CENTIGRADE (CELCIUS) CC COOLING COIL COOLING COIL CCD COOLING COIL CONDENSATE COOLING COIL CONDENSATE DRAIN CD CEILING DIFFUSER CEILING DIFFUSER CD-1 CONSTRUCTION DOCUMENTS (SUBMISSION1)

AutoCAD SHX Text EA EXHAUST AIR EXHAUST AIR EAT ENTERING AIR TEMPERATURE ENTERING AIR TEMPERATURE EC EVAPORATIVE COOLER EVAPORATIVE COOLER ECC ENGINEERING CONTROL CENTER ENGINEERING CONTROL CENTER ECU EVAPORATIVE CONDENSER UNIT EVAPORATIVE CONDENSER UNIT EDH ELECTRIC DUCT HEATER ELECTRIC DUCT HEATER EER ENERGY EFFICIENCY RATIO ENERGY EFFICIENCY RATIO EF EXHAUST FAN EXHAUST FAN EG EXHAUST GRILLE EXHAUST GRILLE EGS EMERGENCY GAS SHUTOFF EMERGENCY GAS SHUTOFF EGT ENTERING GLYCOL TEMPERATURE EH EXHAUST HOOD EXHAUST HOOD EJ EXPANSION JOINT EXPANSION JOINT EMD END OF MAIN DRIP (STEAM) END OF MAIN DRIP (STEAM) ENT ENTERING ER EXHAUST REGISTER EXHAUST REGISTER ERC ELECTRIC REHEAT COIL ELECTRIC REHEAT COIL ERP ELECTRIC RADIANT PANEL ELECTRIC RADIANT PANEL ESP EXTERNAL STATIC PRESSURE EXTERNAL STATIC PRESSURE ET EXPANSION TANK EXPANSION TANK ETO ETHYLENE OXIDE ETHYLENE OXIDE EUH ELECTRIC UNIT HEATER ELECTRIC UNIT HEATER EWC EVAPORATIVE WATER COOLER EVAPORATIVE WATER COOLER EWT ENTERING WATER TEMPERATURE ENTERING WATER TEMPERATURE EX. EXISTING EXISTING

AutoCAD SHX Text F FAHRENHEIT FAHRENHEIT F&T FLOAT AND THERMOSTATIC FLOAT AND THERMOSTATIC F/SDPR COMBINATION FIRE SMOKE DAMPER FA FREE AREA FREE AREA FC FLEXIBLE CONNECTION FLEXIBLE CONNECTION FCU FAN COIL UNIT (4 PIPE) FAN COIL UNIT (4 PIPE) FCUC FAN COIL UNIT COOLING ONLY FAN COIL UNIT COOLING ONLY FCUH FAN COIL UNIT HEATING ONLY FCW FORWARD CURVED WHEEL (FAN) FORWARD CURVED WHEEL (FAN) FD FLOOR DRAIN FLOOR DRAIN FD FIRE DAMPER FIRE DAMPER FF FINAL FILTER FINAL FILTER FHX FLUE GAS/FEEDWATER HEAT FLUE GAS/FEEDWATER HEAT EXCHANGER FM FLOW METER FLOW METER FOP FUEL OIL PUMP FUEL OIL PUMP FOT FUEL OIL TANK FUEL OIL TANK FOHX FUEL OIL HEAT EXCHANGER FUEL OIL HEAT EXCHANGER FPM FEET PER MINUTE FEET PER MINUTE FPS FEET PER SECOND FEET PER SECOND FPTU FAN POWERED TERMINAL UNIT FAN POWERED TERMINAL UNIT FR FLOOR REGISTER FLOOR REGISTER FRP FIBER REINFORCED POLYESTER FIBER REINFORCED POLYESTER FS FLOW SWITCH FLOW SWITCH FSTAT FREEZESTAT FT FEET FEET FT-LB FOOT-POUND FTR FIN TUBE RADIATION FIN TUBE RADIATION FV FACE VELOCITY FACE VELOCITY

AutoCAD SHX Text GA GAUGE GAUGE GAL GALLONS GH GRAVITY HOOD GRAVITY HOOD GPD GALLONS PER DAY GALLONS PER DAY GPH GALLONS PER HOUR GALLONS PER HOUR GPM GALLONS PER MINUTE GALLONS PER MINUTE GPR GAS PRESSURE REGULATOR GAS PRESSURE REGULATOR GS GALVANIZED STEEL GALVANIZED STEEL

AutoCAD SHX Text H HUMIDIFER H&CW HOT & COLD WATER HAC HOUSEKEEPING AID CLOSET HOUSEKEEPING AID CLOSET HB HOSE BIBB HOSE BIBB HC HEATING COIL HEATING COIL HD HEAD HEAD HD HOOD HOOD HOA HAND/OFF/AUTOMATIC HAND/OFF/AUTOMATIC HP HEAT PUMP HEAT PUMP HP HORSEPOWER HORSEPOWER HPDT HIGH PRESSURE DRIP TRAP HIGH PRESSURE DRIP TRAP HPR HIGH PRESSURE RETURN HIGH PRESSURE RETURN (STEAM CONDENSATE) HPS HIGH PRESSURE SUPPLY HIGH PRESSURE SUPPLY (STEAM) HRC HEAT RECOVERY COIL HEAT RECOVERY COIL HRD HEAT RECOVERY DEVICE HEAT RECOVERY DEVICE HRP HYDRONIC RADIANT (CEILING) HYDRONIC RADIANT (CEILING) PANEL HRW HEAT RECOVERY WHEEL HEAT RECOVERY WHEEL HSTAT HUMIDISTAT HTM HUMIDIFIER TERMINAL HUMIDIFIER TERMINAL HUM HUMIDIFIER UNIT MOUNTED HUMIDIFIER UNIT MOUNTED HVU HEATING AND VENTILATING UNIT HEATING AND VENTILATING UNIT HW HOT WATER HOT WATER HWC HOT WATER COIL HOT WATER COIL HWHC HOT WATER HEATING COIL HWP HEATING HOT WATER PUMP HEATING HOT WATER PUMP HWR HEATING HOT WATER RETURN HEATING HOT WATER RETURN HWS HEATING HOT WATER SUPPLY HEATING HOT WATER SUPPLY HWUH HOT WATER UNIT HEATER HVD HOISTWAY VENT DAMPER HOISTWAY VENT DAMPER HX HEAT EXCHANGER HEAT EXCHANGER HZ HERTZ HERTZ

AutoCAD SHX Text OA OUTSIDE AIR OUTSIDE AIR OAG OUTSIDE AIR GRILLE OUTSIDE AIR GRILLE OAI OUTSIDE AIR INTAKE OUTSIDE AIR INTAKE OD OUTSIDE DIAMETER OUTSIDE DIAMETER OFM OIL FLOWMETER OR OPERATING ROOM OPERATING ROOM

AutoCAD SHX Text NA NOT APPLICABLE NOT APPLICABLE NC NOISE CRITERIA NOISE CRITERIA NC NORMALLY CLOSED NORMALLY CLOSED NG NATURAL GAS NATURAL GAS NGFM NATURAL GAS FLOWMETER NO NORMALLY OPEN NORMALLY OPEN NOAA NATIONAL OCEANIC & ATMOSPHERIC NATIONAL OCEANIC & ATMOSPHERIC ADMINISTRATION NOM NOMINAL NOMINAL NPLV NON-STANDARD PART LOAD VALUE NON-STANDARD PART LOAD VALUE NPSH NET POSITIVE SUCTION HEAD NTS NOT TO SCALE NOT TO SCALE

AutoCAD SHX Text M METER, SI UNIT METER, SI UNIT M/s METERS PER SECOND METERS PER SECOND (OR METERS/SECOND) MA MIXED AIR MIXED AIR MAT MIXED AIR TEMPERATURE MIXED AIR TEMPERATURE MAU MAKE-UP AIR UNIT MAKE-UP AIR UNIT MAV MANUAL AIR VENT MANUAL AIR VENT MAX MAXIMUM MAXIMUM MB MIXING BOX MIXING BOX MBH 1000 BTUH 1000 BTUH MCA MINIMUM BRANCH CIRCUIT AMPACITY MINIMUM BRANCH CIRCUIT AMPACITY MER MECHANICAL EQUIPMENT ROOM MECHANICAL EQUIPMENT ROOM MERV MINIMUM EFFICIENCY REPORTING MINIMUM EFFICIENCY REPORTING VALUE MH MANHOLE MANHOLE MHP MOTOR HORSEPOWER MOTOR HORSEPOWER MIN MINIMUM MINIMUM MM MILLIMETER MILLIMETER MOV MOTOR OPERATED VALVE MOTOR OPERATED VALVE MPR MEDIUM PRESSURE RETURN (STEAM CONDENSATE) MPS MEDIUM PRESSURE STEAM MEDIUM PRESSURE STEAM MRI MAGNETIC RESONANCE IMAGING MAGNETIC RESONANCE IMAGING MTD MEAN TEMPERATURE DIFFERENCE MEAN TEMPERATURE DIFFERENCE MVD MANUAL VOLUME DAMPER MANUAL VOLUME DAMPER

AutoCAD SHX Text L LITER LITER L/h LITERS PER HOUR (OR LITERS/HOUR) LITERS PER HOUR (OR LITERS/HOUR) L/m LITERS PER MINUTE (OR LITERS/MINUTE) LITERS PER MINUTE (OR LITERS/MINUTE) L/s LITERS PER SECOND (OR LITERS/SECOND) LITERS PER SECOND (OR LITERS/SECOND) LAT LEAVING AIR TEMPERATURE LEAVING AIR TEMPERATURE LBS/HR POUNDS PER HOUR LF LINEAR FOOT (FEET) LINEAR FOOT (FEET) LGT LEAVING GLYCOL TEMPERATURE LH LATENT HEAT LATENT HEAT LPG LIQUID PROPANE GAS LIQUID PROPANE GAS LPR LOW PRESSURE RETURN (STEAM CONDENSATE) LOW PRESSURE RETURN (STEAM CONDENSATE) LPRC LOW PRESSURE STEAM RETURN (CLEAN) LOW PRESSURE STEAM RETURN (CLEAN) LLHX LIQUID TO LIQUID HEAT EXCHANGER LIQUID TO LIQUID HEAT EXCHANGER LPS LOW PRESSURE STEAM LOW PRESSURE STEAM LPSC LOW PRESSURE STEAM (CLEAN) LOW PRESSURE STEAM (CLEAN) LSD LINEAR SLOT DIFFUSER LINEAR SLOT DIFFUSER LTCP LOCAL TEMPERATURE CONTROL PANEL LOCAL TEMPERATURE CONTROL PANEL LVG LEAVING LVR LOUVER LOUVER LWT LEAVING WATER TEMPERATURE LEAVING WATER TEMPERATURE

AutoCAD SHX Text kg KILOGRAM KILOGRAM kg/HR KILOGRAM PER HOUR kPa KILOPASCAL KILOPASCAL kW KILOWATT KILOWATT kWh KILOWATT HOUR KILOWATT HOUR

AutoCAD SHX Text

J INTENTIALLY LEFT BLANK

AutoCAD SHX Text I/O INPUT/OUTPUT INPUT/OUTPUT IAQ INDOOR AIR QUALITY INDOOR AIR QUALITY IBT INVERTED BUCKET TRAP INVERTED BUCKET TRAP ICF IN-LINE CENTRIFUGAL FAN IN-LINE CENTRIFUGAL FAN ICU INTENSIVE CARE UNIT INTENSIVE CARE UNIT ID INSIDE DIAMETER INSIDE DIAMETER IFB INTEGRAL FACE AND BYPASS INTEGRAL FACE AND BYPASS IN INCHES IN HG INCHES OF MERCURY IN WC INCH WATER COLUMN IN WG INCH WATER GAUGE IN-LB INCH-POUND IPLV INTERGRATED PART LOAD VALUE INTERGRATED PART LOAD VALUE IRH INTRARED HEATER INTRARED HEATER IS INSECT SCREEN INSECT SCREEN IU INDUCTION UNIT INDUCTION UNIT IV INLET VANES INLET VANES

AutoCAD SHX Text T & PCV TEMPERATURE AND PRESSURE CONTROL VALVE TAB TESTING, ADJUSTING, BALANCE TESTING, ADJUSTING, BALANCE TD TEMPERATURE DIFFERENCE TEMPERATURE DIFFERENCE TDH TOTAL DYNAMIC HEAD TOTAL DYNAMIC HEAD TDS TOTAL DISSOLVED SOLIDS TOTAL DISSOLVED SOLIDS TG TRANSFER GRILLE TRANSFER GRILLE TP TRAP TRAP TR TOP REGISTER TOP REGISTER TSP TOTAL STATIC PRESSURE TOTAL STATIC PRESSURE TSTAT THERMOSTAT THERMOSTAT TU TERMINAL UNIT TERMINAL UNIT TWU THRU-WALL UNIT THRU-WALL UNIT

AutoCAD SHX Text SA SUPPLY AIR SUPPLY AIR SAD SOUND ATTENUATING DEVICE SOUND ATTENUATING DEVICE SAT SUPPLY AIR TEMPERATURE SUPPLY AIR TEMPERATURE SC SHADING COEFFICIENT SHADING COEFFICIENT SCFM STANDARD CUBIC FEET PER MINUTE SCI SPINAL CODE INJURY SCR SILICON CONTROLLED RECTIFIER SILICON CONTROLLED RECTIFIER SD SMOKE DETECTOR SMOKE DETECTOR SD SUPPLY AIR DIFFUSER SUPPLY AIR DIFFUSER SD-1 SCHEMATIC DESIGN (SUBMISSION1) SD-2 SCHEMATIC DESIGN (SUBMISSION2) SDPR SMOKE DAMPER SMOKE DAMPER SDR SMOKE DAMPER (RETURN) SDS SMOKE DAMPER (SUPPLY) SEN SENSIBLE HEAT SENSIBLE HEAT SF SUPPLY FAN SUPPLY FAN SG SUPPLY AIR GRILLE SUPPLY AIR GRILLE SH STEAM HUMIDIFIER STEAM HUMIDIFIER SHC STEAM HEATING COIL SI SQUARE INCHES SQUARE INCHES SP STATIC PRESSURE STATIC PRESSURE SP GR SPECIFIC GRAVITY SPD SUPPLY PROCESS AND DISTRIBUTION SPRV STEAM PRESSURE REDUCING VALVE SPS STATIC PRESSURE SENSOR STATIC PRESSURE SENSOR SQ FT SQUARE FOOT (FEET) SR SUPPLY AIR REGISTER SUPPLY AIR REGISTER SS STAINLESS STEEL STAINLESS STEEL SSHX STEAM TO STEAM HEAT EXCHANGER SSR SOLID SEPARATOR SOLID SEPARATOR ST STEAM TRAP SUH STEAM UNIT HEATER SV STEAM PRESSURE REDUCING VALVE STEAM PRESSURE REDUCING VALVE SVS STEAM VENT SILENCER SWHX STEAM TO WATER HEAT EXCHANGER

AutoCAD SHX Text R/E RETURN OR EXHAUST RETURN OR EXHAUST RA RETURN AIR RETURN AIR RAD REFRIGERANT AIR DRYER RAF RADIO FREQUENCY RAHX ROTARY AIR HEAT EXCHANGER RAT RETURN AIR TEMPERATURE RETURN AIR TEMPERATURE RCCH REMOTE CONDENSER CHILLER RCU RECIPROCATING CHILLER UNIT RECIPROCATING CHILLER UNIT RD REFRIGERANT DISCHARGE REFRIGERANT DISCHARGE RDS ROOM DATA SHEETS ROOM DATA SHEETS REA RELIEF AIR RELIEF AIR RF RETURN FAN RETURN FAN RG RETURN GRILLE RETURN GRILLE RH RELATIVE HUMIDITY RELATIVE HUMIDITY RHC REHEAT COIL REHEAT COIL RHG REFRIGERANT HOT GAS REFRIGERANT HOT GAS RL REFRIGERANT LIQUID LINE REFRIGERANT LIQUID LINE RLA RUN LOAD AMPERE RUN LOAD AMPERE RO REVERSE OSMOSIS REVERSE OSMOSIS RPM REVOLUTIONS PER MINUTE REVOLUTIONS PER MINUTE RR RETURN REGISTER RETURN REGISTER RS REFRIGERANT SUCTION REFRIGERANT SUCTION RTU ROOF TOP UNIT ROOF TOP UNIT RV RELIEF VALVE RELIEF VALVE

AutoCAD SHX Text P PUMP PUMP PA PASCAL PASCAL PC PUMPED CONDENSATE PUMPED CONDENSATE PCF POUNDS PER CUBIC FOOT (FEET) POUNDS PER CUBIC FOOT (FEET) PD PRESSURE DROP PRESSURE DROP PEF PROPELLER (TYPE) EXHAUST FAN PROPELLER (TYPE) EXHAUST FAN PF PRE-FILTER PRE-FILTER PG PRESSURE GAGE PRESSURE GAGE PGW PROPYLENE GLYCOL-WATER (SOLUTION) PROPYLENE GLYCOL-WATER (SOLUTION) PHC PREHEAT COIL PREHEAT COIL PPM PARTS PER MILLION PARTS PER MILLION PRS PRESSURE REGULATING (VALVE) STATION PRESSURE REGULATING (VALVE) STATION PRV PRESSURE REGULATING VALVE PRESSURE REGULATING VALVE PSI POUNDS PER SQUARE INCH POUNDS PER SQUARE INCH PSIA POUNDS PER SQUARE INCH – ABSOLUTE POUNDS PER SQUARE INCH – ABSOLUTE ABSOLUTE PSIG POUNDS PER SQUARE INCH – GAGE POUNDS PER SQUARE INCH – GAGE GAGE PSS PRIMARY SECONDARY SYSTEM PRIMARY SECONDARY SYSTEM PSV PRESSURE SAFETY VALVE PRESSURE SAFETY VALVE PTAC PACKAGED TERMINAL AIR CONDITIONER PACKAGED TERMINAL AIR CONDITIONER

AutoCAD SHX Text W WATTS Wb WET-BULB (TEMPERATURE) WET-BULB (TEMPERATURE)

AutoCAD SHX Text V VALVE VALVE VAF VANE-AXIAL FAN VANE-AXIAL FAN VAV VARIABLE AIR VOLUME VARIABLE AIR VOLUME VD VOLUME DAMPER (MANUAL OPPOSED BLADE) VOLUME DAMPER (MANUAL OPPOSED BLADE) VFD VARIABLE FREQUENCY DRIVE VARIABLE FREQUENCY DRIVE VHA VETERANS HEALTH ADMINISTRATION VI VIBRATION ISOLATOR VIBRATION ISOLATOR VP VACUUM PUMP VACUUM PUMP VPS VARIABLE PRIMARY SYSTEM VR VACUUM (STEAM CONDENSATE) RETURN VACUUM (STEAM CONDENSATE) RETURN VSD VARIABLE SPEED DRIVE

AutoCAD SHX Text UC UNDER CUT UNDER CUT UC UNIT COOLER UNIT COOLER UH UNIT HEATER UNIT HEATER UL UNDERWRITERS LABORATORY UNDERWRITERS LABORATORY URV UPBLAST UNIT VENTILATORUPBLAST UNIT VENTILATOR

AutoCAD SHX Text

%%UDRAWING SYMBOLS

AutoCAD SHX Text

AutoCAD SHX Text H4

AutoCAD SHX Text H7

AutoCAD SHX Text A

AutoCAD SHX Text

26-SF 3

AutoCAD SHX Text

26-TU-I-I

AutoCAD SHX Text

DETAIL NUMBER

AutoCAD SHX Text

DRAWING NUMBER WHERE SHOWN

AutoCAD SHX Text

SECTION LETTER

AutoCAD SHX Text

TYPICAL UNIT NO.

AutoCAD SHX Text

BUILDING NO. WHERE EQUIPMENT IS LOCATED.

AutoCAD SHX Text

SUPPLY FAN NO. 3 IN BUILDING NO. 26

AutoCAD SHX Text

EQUIPMENT ABBREVIATION (SUPPLY FAN)

AutoCAD SHX Text

ITEM NUMBER (TERMINAL UNIT NO. 1)

AutoCAD SHX Text

ITEM (TERMINAL UNIT SHOWN)

AutoCAD SHX Text

SERVED BY AIR HANDLER UNIT NO. 1

AutoCAD SHX Text

DRAWING NUMBER WHERE DRAWN

AutoCAD SHX Text

BUILDING NO. WHERE EQUIPMENT IS LOCATED

AutoCAD SHX Text

%%UDUCTWORK SYMBOLS

AutoCAD SHX Text

LIMIT OF DEMOLITION

AutoCAD SHX Text

(WALL TYPE)

AutoCAD SHX Text

(WALL TYPE)

AutoCAD SHX Text

DN

AutoCAD SHX Text

DN

AutoCAD SHX Text

UP

AutoCAD SHX Text

UP

AutoCAD SHX Text

SUPPLY DUCT (UP & DOWN)

AutoCAD SHX Text

EXHAUST DUCT (UP & DOWN)

AutoCAD SHX Text

ROUND AND SQUARE 4-WAY CEILING DIFFUSERS

AutoCAD SHX Text

SUPPLY TOP REGISTER OR GRILLE (WALL TYPE)

AutoCAD SHX Text

EXHAUST OR RETURN CEILING REGISTER OR GRILLE

AutoCAD SHX Text

EXHAUST OR RETURN BOTTOM REGISTER OR GRILLE

AutoCAD SHX Text

EXHAUST OR RETURN REGISTER OR TOP GRILLE

AutoCAD SHX Text

VANED ELBOW & AIR SPLIT TYPE DUCT TAKE-OFF

AutoCAD SHX Text

CONNECT NEW DUCT TO EXISTING DUCT

AutoCAD SHX Text D

AutoCAD SHX Text

INCLINED RISE, IN DIRECTION OF AIR FLOW

AutoCAD SHX Text

INCLINED DROP, IN DIRECTION OF AIR FLOW

AutoCAD SHX Text R

AutoCAD SHX Text

DN

AutoCAD SHX Text

UP

AutoCAD SHX Text

RETURN DUCT (UP & DOWN)

AutoCAD SHX Text

SQUARE 3-WAY CEILING DIFFUSERS

AutoCAD SHX Text

SQUARE 2-WAY CEILING DIFFUSERS

AutoCAD SHX Text

LINEAR SLOT DIFFUSER

AutoCAD SHX Text

SQUARE 1-WAY CEILING DIFFUSERS

AutoCAD SHX Text

BACK DRAFT DAMPER

AutoCAD SHX Text

BDD

AutoCAD SHX Text

SECTION.)

AutoCAD SHX Text

FC

AutoCAD SHX Text 10x8

AutoCAD SHX Text

FLEXIBLE CONNECTION, EQUIPMENT,

AutoCAD SHX Text

VANED ELBOW (PROVIDE ALL SQUARE OR

AutoCAD SHX Text

RECTANGULAR ELBOWS WITH VANES EVEN IF

AutoCAD SHX Text

SYMBOL IS MISSING)

AutoCAD SHX Text

VANED ELBOW (SHORT RADIUS)

AutoCAD SHX Text

STANDARD RADIUS ELBOW (LONG RADIUS)

AutoCAD SHX Text NEW DUCT (INSIDE DIMENSIONS: WIDTH x DEPTH)

AutoCAD SHX Text

EXISTING DUCT TO REMAIN

AutoCAD SHX Text

LOUVER (LOUVER SPECIFIED IN ARCHITECTURAL

AutoCAD SHX Text

FIRE DAMPER

AutoCAD SHX Text

FD

AutoCAD SHX Text

VD

AutoCAD SHX Text

DUCT WITH SOUND LINING

AutoCAD SHX Text

FLEXIBLE DUCTWORK (INSULATED)

AutoCAD SHX Text

MANUAL VOLUME DAMPER

AutoCAD SHX Text

EXISTING DUCT TO BE REMOVED

AutoCAD SHX Text

VIBRATION, OR SEISMIC

AutoCAD SHX Text

%%UDUCTWORK SYMBOLS

AutoCAD SHX Text

DUCT MOUNTED COIL

AutoCAD SHX Text

DUCT MOUNTED COIL

AutoCAD SHX Text

SUPPLY

AutoCAD SHX Text

RETURN

AutoCAD SHX Text 45%%d

AutoCAD SHX Text RETURN, NO SPLITTER (45%%d TAP)

AutoCAD SHX Text

STANDARD BRANCH SUPPLY OR

AutoCAD SHX Text

MANUAL SPLITTER DAMPER

AutoCAD SHX Text 45%%d

AutoCAD SHX Text N

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

POINT OF CHANGE IN DUCT CONSTRUCTION BY

AutoCAD SHX Text

STATIC PRESSURE CLASS. THE NUMBER ASSIGNS

AutoCAD SHX Text

PRESSURE CLASS (IN. OF WATER) WHICH WILL

AutoCAD SHX Text

ACCOMMODATE MAXIMUM OPERATING PRESSURE

AutoCAD SHX Text

COMBINATION FIRE/SMOKE DAMPER

AutoCAD SHX Text 1/2

AutoCAD SHX Text

AutoCAD SHX Text

IN THE DUCT SUBSECTION. THE SYMBOL CONTINUES

AutoCAD SHX Text

THE ASSIGNMENT UNTIL THE DUCT TERMINATES OR

AutoCAD SHX Text

ANOTHER SYMBOL APPEARS. A "N" SUPERSCRIPT

AutoCAD SHX Text

INDICATES NEGATIVE PRESSURE.

AutoCAD SHX Text

STAINLESS STEEL DUCT

AutoCAD SHX Text

(ELECTRIC)

AutoCAD SHX Text

F/S DPR

AutoCAD SHX Text

AUTOMATIC CONTROL DAMPER MODULATING

AutoCAD SHX Text

AUTOMATIC CONTROL DAMPER TWO POSITION

AutoCAD SHX Text

%%UTERMINAL UNIT SYMBOLS

AutoCAD SHX Text

UNIT HEATER (HORIZONTAL)

AutoCAD SHX Text

%%UAIR TERMINAL SYMBOLS

AutoCAD SHX Text

TERMINAL UNIT WITH REHEAT COIL

AutoCAD SHX Text

%%UPIPING SYMBOLS

AutoCAD SHX Text

HIGH PRESSURE STEAM CONDENSATE RETURN

AutoCAD SHX Text

HIGH PRESSURE STEAM (60 PSIG AND ABOVE)

AutoCAD SHX Text

HOT WATER HEATING SUPPLY

AutoCAD SHX Text

CONDENSATE PUMP DISCHARGE

AutoCAD SHX Text

LOW PRESSURE STEAM CONDENSATE RETURN

AutoCAD SHX Text

LOW PRESSURE STEAM (15 PSIG AND BELOW)

AutoCAD SHX Text

MEDIUM PRESSURE STEAM CONDENSATE RETURN

AutoCAD SHX Text

MEDIUM PRESSURE STEAM (16 PSIG THRU 59 PSIG)

AutoCAD SHX Text

VENT LINE

AutoCAD SHX Text

REFRIGERANT SUCTION

AutoCAD SHX Text

REFRIGERANT HOT GAS

AutoCAD SHX Text

REFRIGERANT LIQUID

AutoCAD SHX Text

CHILLED WATER SUPPLY

AutoCAD SHX Text

CHILLED WATER RETURN

AutoCAD SHX Text

DRAIN LINE

AutoCAD SHX Text

MAKE-UP WATER

AutoCAD SHX Text

HOT WATER HEATING RETURN

AutoCAD SHX Text

HPS

AutoCAD SHX Text

HPR

AutoCAD SHX Text

MPS

AutoCAD SHX Text

MPR

AutoCAD SHX Text

LPS

AutoCAD SHX Text

LPR

AutoCAD SHX Text

PC

AutoCAD SHX Text

HWS

AutoCAD SHX Text

HWR

AutoCAD SHX Text V

AutoCAD SHX Text

CHR

AutoCAD SHX Text

RL

AutoCAD SHX Text

RS

AutoCAD SHX Text

RHG

AutoCAD SHX Text

CHS

AutoCAD SHX Text

MW

AutoCAD SHX Text D

AutoCAD SHX Text X

AutoCAD SHX Text

EXISTING PIPE TO BE REMOVED

AutoCAD SHX Text

%%UGENERAL PIPING SYMBOLS

AutoCAD SHX Text

ANCHOR

AutoCAD SHX Text

REDUCER OR INCREASER

AutoCAD SHX Text

DIRECTION OF FLOW

AutoCAD SHX Text

SIDE CONNECTION

AutoCAD SHX Text

ECCENTRIC REDUCER

AutoCAD SHX Text BOTTOM CONNECTION, 45%%d OR 90%%d

AutoCAD SHX Text TOP CONNECTION, 45%%d OR 90%%d

AutoCAD SHX Text

DIRECTION OF PIPE PITCH (DOWN)

AutoCAD SHX Text

UNION

AutoCAD SHX Text

RISE OR DROP IN PIPE

AutoCAD SHX Text

CAPPED OUTLET

AutoCAD SHX Text

PRESSURE GAGE

AutoCAD SHX Text

THERMOMETER

AutoCAD SHX Text

FLOW ELEMENT

AutoCAD SHX Text

FLOAT & THERMOSTATIC TRAP SET INCLUDING

AutoCAD SHX Text

PIPING ACCESSORIES SEE DETAIL

AutoCAD SHX Text

PIPING ACCESSORIES SEE DETAIL

AutoCAD SHX Text

INVERTED BUCKET TRAP SET INCLUDING

AutoCAD SHX Text

FE

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

PIPE UP

AutoCAD SHX Text

PIPE DOWN

AutoCAD SHX Text

REFRIGERANT SIGHT GLASS

AutoCAD SHX Text

TEST PLUG (PRESSURE/TEMPERATURE)

AutoCAD SHX Text

AUTOMATIC AIR VENT

AutoCAD SHX Text

AV

AutoCAD SHX Text

MANUAL AIR VENT

AutoCAD SHX Text

MV

AutoCAD SHX Text

THERMOSTATIC TRAP SET INCLUDING

AutoCAD SHX Text

PIPING ACCESSORIES SEE DETAIL

AutoCAD SHX Text

QUICK-COUPLE HOSE CONNECTOR

AutoCAD SHX Text

%%UVALVE SYMBOLS

AutoCAD SHX Text

BALL VALVE

AutoCAD SHX Text

GATE VALVE WITH 3/4" HOSE ADAPTER

AutoCAD SHX Text

CHECK VALVE

AutoCAD SHX Text

ANGLE GLOBE VALVE

AutoCAD SHX Text

BUTTERFLY VALVE

AutoCAD SHX Text

MODULATING CONTROL VALVE

AutoCAD SHX Text

TWO POSITION CONTROL VALVE

AutoCAD SHX Text

THREE-WAY MODULATING CONTROL VALVE

AutoCAD SHX Text

AUTOMATIC BALANCING CONTROL VALVE

AutoCAD SHX Text

PRESSURE SAFETY VALVE

AutoCAD SHX Text

GATE VALVE - THREADED/FLANGED

AutoCAD SHX Text

GLOBE VALVE - THREADED/FLANGED

AutoCAD SHX Text

PRESSURE REGULATING VALVE

AutoCAD SHX Text

THREE-WAY TWO POSITION CONTROL VALVE

AutoCAD SHX Text

WYE STRAINER (WITH BALL VALVE & HOSE CONNECTION)

AutoCAD SHX Text

FLEXIBLE CONNECTION

AutoCAD SHX Text

WATER BALANCE DEVICE

AutoCAD SHX Text

MODULATING CONTROL BUTTERFLY VALVE

AutoCAD SHX Text

CIRCUIT SETTER VALVE

AutoCAD SHX Text

GATE VALVE WITH GLOBE-VALVED BYPASS

AutoCAD SHX Text

PLUG VALVE

AutoCAD SHX Text

CONTROL VALVE (CV) - FLOAT-OPERATED

AutoCAD SHX Text

PRESSURE REDUCING VALVE (PRV)

AutoCAD SHX Text

FLOW METER

AutoCAD SHX Text M

AutoCAD SHX Text

%%UCONTROLS SYMBOLS

AutoCAD SHX Text T

AutoCAD SHX Text

ROOM THERMOSTAT/TRANSMITTER - WALL MOUNT

AutoCAD SHX Text

TT

AutoCAD SHX Text

TEMPERATURE TRANSMITTER

AutoCAD SHX Text M

AutoCAD SHX Text

ROOM HUMIDISTAT (MOISTURE)/TRANSMITTER - WALL MOUNT

AutoCAD SHX Text

MT

AutoCAD SHX Text

MOISTURE (HUMIDITY) TRANSMITTER

AutoCAD SHX Text

PT

AutoCAD SHX Text

PRESSURE TRANSMITTER

AutoCAD SHX Text

TT

AutoCAD SHX Text

TEMPERATURE TRANSMITTER, AVERAGING ELEMENT

AutoCAD SHX Text

FT

AutoCAD SHX Text

FLOW TRANSMITTER

AutoCAD SHX Text

IT

AutoCAD SHX Text

CURRENT TRANSMITTER

AutoCAD SHX Text

CT

AutoCAD SHX Text

CONDUCTIVITY TRANSMITTER

AutoCAD SHX Text

SPS

AutoCAD SHX Text

STATIC PRESSURE SENSOR

AutoCAD SHX Text

SD

AutoCAD SHX Text

SMOKE DETECTOR

AutoCAD SHX Text

PDT

AutoCAD SHX Text

PRESSURE DIFFERENTIAL TRANSMITTER

AutoCAD SHX Text

KR

AutoCAD SHX Text

LOCAL RECORDING TIME CLOCK (RUNTIME)

AutoCAD SHX Text

TSL

AutoCAD SHX Text

TEMPERATURE SWITCH, LOW (FREEZESTAT)

AutoCAD SHX Text

HS

AutoCAD SHX Text

HAND SWITCH (HAND-OFF-AUTO SWITCH)

AutoCAD SHX Text

ZC

AutoCAD SHX Text

VALVE OR DAMPER POSITION CONTROLLER

AutoCAD SHX Text

LC

AutoCAD SHX Text

LEVEL CONTROLLER

AutoCAD SHX Text

LT

AutoCAD SHX Text

LEVEL TRANSMITTER

AutoCAD SHX Text

PDS

AutoCAD SHX Text

PRESSURE DIFFERENTIAL SWITCH

AutoCAD SHX Text

TSH

AutoCAD SHX Text

TEMPERATURE SWITCH, HIGH (FREEZESTAT)

AutoCAD SHX Text

EPT

AutoCAD SHX Text

ELECTRONIC TO PNEUMATIC TRANSDUCER

AutoCAD SHX Text

AT

AutoCAD SHX Text

CARBON DIOXIDE TRANSMITTER

AutoCAD SHX Text

CARBON MONOXIDE TRANSMITTER

AutoCAD SHX Text

CO2

AutoCAD SHX Text

AT

AutoCAD SHX Text

CO

AutoCAD SHX Text

OCCUPANCY SENSOR

AutoCAD SHX Text

AT

AutoCAD SHX Text

OC

AutoCAD SHX Text

LTCP

AutoCAD SHX Text

LOCAL TEMPERATURE CONTROL PANEL

AutoCAD SHX Text

HVAC

AutoCAD SHX Text

HVAC CONTROL PANEL

AutoCAD SHX Text

ECC

AutoCAD SHX Text

INTEGRATE CONTROL POINT ON REMOTE GRAPHICS WORKSTATION AT ENERGY CONTROL CENTER

AutoCAD SHX Text

TC

AutoCAD SHX Text

TEMPERATURE CONTROLLER. SEE SEQUENCE OF OPERATION

AutoCAD SHX Text

VSMC

AutoCAD SHX Text

VARIABLE SPEED MOTOR CONTROLLER

AutoCAD SHX Text

PC

AutoCAD SHX Text

PRESSURE CONTROLLER. SEE SEQUENCE OF OPERATION

AutoCAD SHX Text

SC

AutoCAD SHX Text

SPEED CONTROLLER. SEE SEQUENCE OF OPERATION

AutoCAD SHX Text

FC

AutoCAD SHX Text

FLOW CONTROLLER. SEE SEQUENCE OF OPERATION

AutoCAD SHX Text

PSH

AutoCAD SHX Text

PRESSURE SWITCH HIGH

AutoCAD SHX Text

FSH

AutoCAD SHX Text

FLOW SWITCH HIGH

AutoCAD SHX Text

PSL

AutoCAD SHX Text

PRESSURE SWITCH LOW

AutoCAD SHX Text

KC

AutoCAD SHX Text

TIME CLOCK CONTROLLING EQUIPMENT ON A SCHEDULE

AutoCAD SHX Text

FSL

AutoCAD SHX Text

FLOW SWITCH LOW

AutoCAD SHX Text

LENGTH IN DUCT WHEN SPACE PERMITS.)

AutoCAD SHX Text A

AutoCAD SHX Text

TEMPERATURE SENSING ELEMENT FOR

AutoCAD SHX Text

TRANSMITTING TEMPERATURE TO EMCS

AutoCAD SHX Text (PROVIDE 12 INCHES [200mm] MINIMUM

AutoCAD SHX Text

SENSOR WITH AVERAGING ELEMENT TO TRANSMIT

AutoCAD SHX Text

TEMPERATURE TO EMCS

AutoCAD SHX Text

MOTOR STARTER

AutoCAD SHX Text M

AutoCAD SHX Text

ELECTRIC OPERATED CONTROL DAMPER/OR VALVE

AutoCAD SHX Text

(HOT WATER OR STEAM COIL)

AutoCAD SHX Text

SUPPLY AIR TAG

AutoCAD SHX Text

RETURN AIR TAG

AutoCAD SHX Text XX"%%c

AutoCAD SHX Text D-1

AutoCAD SHX Text

XXX

AutoCAD SHX Text 24"x24"

AutoCAD SHX Text G-1

AutoCAD SHX Text Drawing Title

AutoCAD SHX Text Approved: Project Director

AutoCAD SHX Text Project Title

AutoCAD SHX Text Date

AutoCAD SHX Text Location

AutoCAD SHX Text Checked

AutoCAD SHX Text Building Number

AutoCAD SHX Text Project Number

AutoCAD SHX Text Drawing Number

AutoCAD SHX Text Drawn

AutoCAD SHX Text Dwg. of

AutoCAD SHX Text Revisions:

AutoCAD SHX Text Date

AutoCAD SHX Text

CONSULTANTS:

AutoCAD SHX Text

ARCHITECT/ENGINEERS:

AutoCAD SHX Text one eighth inch = one foot

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text C

AutoCAD SHX Text D

AutoCAD SHX Text E

AutoCAD SHX Text F

AutoCAD SHX Text three inches = one foot

AutoCAD SHX Text 6"

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 6"

AutoCAD SHX Text one and one half inches = one foot

AutoCAD SHX Text one inch = one foot

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 6"

AutoCAD SHX Text 6"

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text three quarters inch = one foot

AutoCAD SHX Text one half inch = one foot

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text three eighths inch = one foot

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text one quarter inch = one foot

AutoCAD SHX Text

VA FORM 08-6231

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text E

AutoCAD SHX Text D

AutoCAD SHX Text C

AutoCAD SHX Text B

AutoCAD SHX Text A

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text Office of Construction and Facilities Management

AutoCAD SHX Text

RENOVATE 3B FOR INPATIENT WARD

AutoCAD SHX Text

100% CONSTRUCTION DOCUMENTS

AutoCAD SHX Text William S. Middleton Memorial VA, Madison WI

AutoCAD SHX Text 607-15-101

AutoCAD SHX Text Bldg 1 3rd Floor B-Wing

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text 05/30/2017

AutoCAD SHX Text Drawing Title

AutoCAD SHX Text

MECHANICAL SYMBOLS,

AutoCAD SHX Text

ABBREVIATIONS AND GENERAL NOTES

AutoCAD SHX Text M001

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

JCB

AutoCAD SHX Text

DJP

13100 watertown plank road suite 200 elm grove, wi 53122

Nagel Architects Project Number: 150401

Kahler Slater, Inc.

44 E. Mifflin Street

Madison, WI 53703

Ring & DuChateau, LLP

17400 W. Capitol Drive

Brookfield, WI 53045

Environmental Management Consulting, Inc.

W7748 County Highway V

Lake Mills, WI 53551

The Concord Group

55 E. Monroe Street

Suite 2850

Chicago, IL 60603

AutoCAD SHX Text

ASSOCIATED BACK CHARGES AS DEEMED APPROPRIATE BY THE ARCHITECT/ENGINEER.

AutoCAD SHX Text OR ARCHITECT/ENGINEER TO MAKE CHANGES WHICH WOULD ALLOW THE EQUIPMENT TO FIT IN THE

AutoCAD SHX Text SHALL ALSO PAY ALL COSTS FOR ADDITIONAL WORK REQUIRED BY OTHER CONTRACTORS, OWNER, AutoCAD SHX Text REQUIRED TO ACCOMMODATE SUCH EQUIPMENT AT NO ADDITIONAL COST TO OWNER. CONTRACTOR

AutoCAD SHX Text ARRANGEMENT OF THAT SCHEDULED AND SPECIFIED, CONTRACTOR SHALL PAY FOR ALL ALTERATIONS

AutoCAD SHX Text

WHEN EQUIPMENT IS SUBMITTED FOR REVIEW AND DOES NOT MEET THE PHYSICAL SIZE OR

AutoCAD SHX Text

EQUIPMENT AFTER IT IS IN THE SPACE AT HIS OWN EXPENSE.

AutoCAD SHX Text HOUSING FOR ENTRANCE INTO THE EXISTING SPACE OR BUILDING. CONTRACTOR SHALL REASSEMBLE

AutoCAD SHX Text CONDITION. CONTRACTOR MAY ELECT TO ORDER THE EQUIPMENT DISASSEMBLED AND/OR WITH SPLIT

AutoCAD SHX Text

EXPENSE, PROVIDE NEW OR ENLARGED OPENINGS AND RESTORE SAME TO ORIGINAL SIZE AND

AutoCAD SHX Text

THE BUILDING. IF OPENINGS ARE TOO SMALL FOR ACCESS, CONTRACTOR SHALL, AT HIS OWN

AutoCAD SHX Text ROOMS, ETC. FOR ACCESS OF THE NEW EQUIPMENT INTO OR REMOVAL OF EXISTING EQUIPMENT FROM

AutoCAD SHX Text CONTRACTOR SHALL FIELD VERIFY THE SIZE OF EXISTING OPENINGS, LOUVERS, WINDOWS, DOORS, CORRIDORS, AutoCAD SHX Text PHYSICALLY FIT INTO THE SPACE ALLOCATED WITH SUITABLE ACCESS AROUND EQUIPMENT FOR

AutoCAD SHX Text PERMITTED, PROVIDED ALL THE RATINGS MEET THOSE SHOWN ON THE DRAWINGS AND EQUIPMENT WILL

AutoCAD SHX Text WILL FIT IN THE SPACE SHOWN ON THE DRAWINGS. MINOR DEVIATIONS IN DIMENSIONS WILL BE

AutoCAD SHX Text FOR CHECKING ALL THE DIMENSIONS, CAPACITIES AND RATINGS OF THE EQUIPMENT TO VERIFY THAT IT

AutoCAD SHX Text SCHEDULED MANUFACTURER USED FOR THE BASE DESIGN, THE CONTRACTOR SHALL BE RESPONSIBLE

AutoCAD SHX Text PURCHASES EQUIPMENT LISTED AS A SPECIFIED %%uACCEPTABLE MANUFACTURER%%u BUT IS NOT THE

AutoCAD SHX Text FOR EACH PIECE OF EQUIPMENT AS THE BASIS FOR DIMENSIONAL DESIGN. IF THE CONTRACTOR

AutoCAD SHX Text THE DRAWINGS, SCHEDULES AND SPECIFICATIONS HAVE BEEN PREPARED USING ONE MANUFACTURER

AutoCAD SHX Text

WILL BE ALLOWED TO BE STORED ON THE SITE UNLESS IT IS SITTING ON WOOD PLANKS AND

AutoCAD SHX Text DUCTWORK WILL HAVE THE ENDS CLOSED TO KEEP OUT DIRT AND OTHER DEBRIS. NO EQUIPMENT

AutoCAD SHX Text EQUIPMENT MUST BE COMPLETELY COVERED WITH WATERPROOF TARPS OR VISQUIN. ALL PIPING AND

AutoCAD SHX Text MINIMUM OF SIX INCHES (6") SET ON 6 X 6 PLANKS AND/OR WOOD PALLETS. ALL MATERIAL AND

AutoCAD SHX Text AREA. IF MATERIAL IS STORED OUTSIDE OF THE BUILDING, IT MUST BE STORED OFF THE GROUND A

AutoCAD SHX Text CONTRACTOR SHALL STORE ALL MATERIALS AND EQUIPMENT SHIPPED TO THE SITE IN A PROTECTED

AutoCAD SHX Text

ABOVE A SUSPENDED CEILING SHALL BE FROM BUILDING STRUCTURAL MEMBERS ONLY.

AutoCAD SHX Text OF THEIR PIPING, DUCTWORK, CONDUIT, TANKS, EQUIPMENT, ETC. ALL SUPPORTING STEEL FOR ITEMS

AutoCAD SHX Text CONTRACTOR SHALL INSTALL ALL AUXILIARY SUPPORTING STEEL AS REQUIRED FOR THE SUPPORTING

AutoCAD SHX Text

SPACE AND FUNCTION AS INTENDED.

AutoCAD SHX Text

OPERATION AND MAINTENANCE ON THE EQUIPMENT.

AutoCAD SHX Text

COMPLETELY PROTECTED WITH WEATHERPROOF COVERS.

AutoCAD SHX Text 14.

AutoCAD SHX Text 13.

AutoCAD SHX Text 12.

AutoCAD SHX Text 11.

AutoCAD SHX Text 10.

AutoCAD SHX Text

CONTRACTOR TO PERFORM THE CLEAN UP AND THE NEGLIGENT CONTRACTOR SHALL PAY THE

AutoCAD SHX Text CONTRACTOR FAILS TO PROVIDE SUCH CLEAN UP, THE ARCHITECT/ENGINEER WILL DIRECT ANOTHER

AutoCAD SHX Text

CONTRACTOR SHALL BE RESPONSIBLE FOR HIS OWN CLEAN UP DURING CONSTRUCTION. IF

AutoCAD SHX Text

SATISFACTION OF THE ARCHITECT/ENGINEER AND OWNER.

AutoCAD SHX Text WORK SHALL BE REPAIRED, REPLACED AND PAID FOR BY THE INSTALLING CONTRACTOR, TO THE

AutoCAD SHX Text FINISHES THAT ARE DAMAGED DURING THE INSTALLATION OF NEW WORK OR REMOVAL OF EXISTING

AutoCAD SHX Text TO DAMAGE ANY EXISTING BUILDING CONSTRUCTION OR ITEMS THAT ARE TO REMAIN. ANY EXISTING

AutoCAD SHX Text MATCH THE ADJACENT CONSTRUCTION AS CLOSELY AS POSSIBLE. CARE SHALL BE TAKEN SO AS NOT

AutoCAD SHX Text REFINISHING WORK SHALL BE PERFORMED BY THOSE REGULARLY INVOLVED IN THAT TRADE AND SHALL

AutoCAD SHX Text ACCOMMODATE THE INSTALLATION OR REMOVAL OF THEIR WORK. ALL PATCHING, REPAIRING AND

AutoCAD SHX Text

AND REMOVAL/REPLACEMENT OF NEW OR EXISTING BUILDING CONSTRUCTION REQUIRED TO

AutoCAD SHX Text CONTRACTOR SHALL BE RESPONSIBLE FOR ALL CORING, CUTTING, PATCHING, REPAIRING, REFINISHING

AutoCAD SHX Text AS REQUIRED BY JOB SITE CONDITIONS, AND/OR AS SPECIFIED, WHEN INSTALLING THEIR WORK.

AutoCAD SHX Text CONTRACTOR SHALL PROVIDE SLEEVES IN FLOORS, ROOFS AND WALLS AS SHOWN ON THE DRAWINGS, AutoCAD SHX Text AND IN STRICT ACCORDANCE WITH ARCHITECT AND OWNERS STIPULATION AS CALLED FOR IN THE SPECIFICATION

AutoCAD SHX Text THE SEQUENCE FOR THE INSTALLATION OF ALL WORK SHALL BE COORDINATED BETWEEN CONTRACTORS

AutoCAD SHX Text

ADDITIONAL COST TO THE OWNER OR DELAY IN COMPLETION DATE OF THE PROJECT.

AutoCAD SHX Text WORK OF OTHER TRADES AND BUILDING CONSTRUCTION. ALL CHANGES SHALL BE MADE WITHOUT

AutoCAD SHX Text DRAWINGS, SUCH AS OFFSETS, BENDS OR CHANGES IN ELEVATION DUE TO COORDINATION WITH THE

AutoCAD SHX Text CONTRACTOR SHALL MAKE ANY REQUIRED CHANGES FROM THE GENERAL ROUTING SHOWN ON THESE

AutoCAD SHX Text EVERY STRUCTURAL ELEMENT THAT MAY BE ENCOUNTERED DURING THE INSTALLATION OF THIS WORK.

AutoCAD SHX Text ETC., AS SHOWN ON DRAWINGS, DOES NOT INTEND TO SHOW EVERY RISE, DROP, OFFSET, FITTING NOR

AutoCAD SHX Text DRAWINGS ARE GENERALLY DIAGRAMMATIC. ROUTING OF PIPING, DUCTWORK, CONDUITS, RACEWAYS, AutoCAD SHX Text

DRAWINGS MAY BE DISTORTED FOR CLEARNESS OF PRESENTATION.

AutoCAD SHX Text ELEMENTS OF THE BUILDING, NOTWITHSTANDING THE FACT THAT LOCATIONS INDICATED BY THESE

AutoCAD SHX Text IT IS INTENDED THAT EQUIPMENT SHALL BE LOCATED SYMMETRICALLY WITH THE ARCHITECTURAL

AutoCAD SHX Text SPACE CONDITIONS APPEAR INADEQUATE, CONTRACTOR SHALL NOTIFY ARCHITECT/ENGINEER BEFORE

AutoCAD SHX Text MAXIMUM HEADROOM AND SPACE CONDITION AT ALL POINTS IN THE BUILDING. WHERE HEADROOM OR

AutoCAD SHX Text WORK WILL BE INSTALLED ARE CLEAR OF OBSTRUCTIONS. WORK SHALL BE INSTALLED TO MAINTAIN

AutoCAD SHX Text CONTRACTOR SHALL CHECK DRAWINGS OF OTHER TRADES TO VERIFY THAT SPACES IN WHICH THEIR

AutoCAD SHX Text SLEEVES AND OPENINGS, ETC. NEEDED FOR THEIR WORK TO PERMIT OTHER TRADES AFFECTED TO

AutoCAD SHX Text LOCATIONS AND SIZES OF PIPING, DUCTWORK, CONDUIT, RACEWAYS, EQUIPMENT, FRAMES, BOXES, AutoCAD SHX Text CONTRACTOR SHALL FURNISH OTHER TRADES ADVANCE INFORMATION AND/OR SHOP DRAWINGS ON

AutoCAD SHX Text

INSTALLED WITHOUT CONSULTING WITH OTHER TRADES BEFORE INSTALLING THEIR WORK.

AutoCAD SHX Text EXPENSE, FOR THE REMOVAL AND REINSTALLATION OF ANY PART OF THEIR WORK IF SAME WAS

AutoCAD SHX Text WORK OF OTHER TRADES PRIOR TO ROUGH IN. CONTRACTOR SHALL BE RESPONSIBLE, AT HIS OWN

AutoCAD SHX Text EXACT LOCATIONS OF ALL DEVICES AND EQUIPMENT WITH FIELD CONDITIONS, SHOP DRAWINGS, AND

AutoCAD SHX Text SATISFACTORY ADJUSTMENTS TO INSTALLATION OF THE NEW WORK. CONTRACTORS SHALL VERIFY

AutoCAD SHX Text

TRADES, ALL TRADES SHALL MEET ON JOB SITE TO WORK OUT SPACE CONDITIONS AND MAKE

AutoCAD SHX Text

WHERE THERE IS EVIDENCE THAT WORK OF ONE TRADE WILL INTERFERE WITH WORK OF OTHER

AutoCAD SHX Text AND/OR AS DIRECTED. DISRUPTION TO EXISTING BUILDING OPERATIONS TO BE KEPT AT AN ABSOLUTE

AutoCAD SHX Text

INSTALL THEIR WORK PROPERLY AND WITHOUT DELAY.

AutoCAD SHX Text 9.

AutoCAD SHX Text

AutoCAD SHX Text 7.

AutoCAD SHX Text 6.

AutoCAD SHX Text 5.

AutoCAD SHX Text

PROCEEDING WITH THE INSTALLATION OF THEIR WORK.

AutoCAD SHX Text %%uGENERAL NOTES

AutoCAD SHX Text 1.

AutoCAD SHX Text 4.

AutoCAD SHX Text 3.

AutoCAD SHX Text 2.

AutoCAD SHX Text 15.

AutoCAD SHX Text WHERE DRAWINGS, SPECIFICATIONS OR NOTES CONFLICT WITH ONE ANOTHER THE CONTRACTOR SHALL

AutoCAD SHX Text IMMEDIATELY ADVISE THE ARCHITECT/ENGINEER OF SUCH CONFLICTS. FOR PURPOSES OF BIDDING AND

AutoCAD SHX Text PENDING WRITTEN RECEIPT OF ANY DIRECTION TO THE CONTRARY, THE CONTRACTOR SHALL INCLUDE IN

AutoCAD SHX Text

HIS PROPOSAL THE MORE EXPENSIVE ALTERNATE DESCRIBED.

AutoCAD SHX Text 16.

AutoCAD SHX Text WHEREVER EXTENSION, CONNECTIONS, OR CAPPINGS ARE MADE TO EXISTING DUCTWORK OR PIPING AND

AutoCAD SHX Text DAMAGED INSULATION RESULTS FROM SUCH CONNECTION, EXTENSION OR CAPPING, INSULATION SHALL BE

AutoCAD SHX Text REPAIRED AND/OR REPLACED IN A MANNER TO MATCH EXISTING BY THE CONTRACTOR INVOLVED.

AutoCAD SHX Text

MINIMUM.

AutoCAD SHX Text THE CONTROLS CONTRACTOR/ENGINEER SHALL SIZE ALL MODULATING TEMPERATURE CONTROL VALVES WITH A Cv AND PRESSURE DROP SUCH THAT THERE IS LINEAR CONTROL OF WATER FLOW THROUGHOUT THE ENTIRE STROKE OF THE VALVE. COORDINATE WITH THE MECHANICAL CONTRACTOR TO PROVIDE REDUCERS AS REQUIRED FOR MODULATING VALVES THAT ARE NOT LINE SIZE.

AutoCAD SHX Text ALL CONTROL VALVES SHALL SPRING RETURN TO A FAIL SAFE POSITION. ALL HEATING CONTROL VALVES SHALL FAIL OPEN BY SPRING RETURN TO HEATING.

AutoCAD SHX Text THE CONTROLS CONTRACTOR SHALL PROVIDE TEMPERATURE SENSORS FOR ALL CONTROLLED EQUIPMENT TO OPERATE AS DESCRIBED IN THE SEQUENCE OF OPERATION AND/OR PER MANUFACTURER'S REQUIREMENTS AND KNOWN STANDARDS OF GOOD CONTROL PRACTICE. INCLUDE ALL TEMPERATURE SENSORS AS REQUIRED FOR EQUIPMENT TO BE COMPLETE AND FULLY OPERATIONAL WHETHER SHOWN SPECIFICALLY ON THE PLANS OR NOT.

AutoCAD SHX Text THE CONTROLS CONTRACTOR/ENGINEER SHALL SELECT ALL TEMPERATURE SENSORS WITH AN APPROPRIATE SPAN AND RANGE FOR THE APPLICATION.

AutoCAD SHX Text THE PROJECT REQUIRES NEW WALL MOUNTED THERMOSTATS. PROVIDE THE OWNER'S STANDARD THERMOSTAT TYPE. VERIFY THE SPECIFIC REQUIREMENTS WITH THE OWNER.

AutoCAD SHX Text ALL TEMPERATURE SENSORS SHALL BE INSTALLED IN LOCATIONS SUCH THAT THEY DO NOT MAKE FALSE READINGS. CONTROLS CONTRACTOR/ENGINEER SHALL REVIEW THE PLANS AND IDENTIFY ANY SUCH POTENTIAL CAUSES FOR FALSE READINGS AND NOTIFY THE ENGINEER IN WRITING THAT THESE SHOULD BE RELOCATED PRIOR TO ROUGH IN AND CONTROLS INSTALLATION. THE CONTROLS CONTRACTOR SHALL RELOCATE ANY SENSORS INSTALLED IN IMPROPER LOCATIONS AND GIVING FALSE READINGS AT HIS OWN EXPENSE. CONDITIONS TO BE AWARE OF SHALL INCLUDE BUT ARE NOT LIMITED TO LOCATIONS OF THERMOSTATS BEHIND DOORS, THERMOSTATS INSTALLED ADJACENT TO HEAT SOURCES SUCH AS COFFEE POTS, COMPUTERS, VENDING MACHINES AND OTHER APPLIANCES, ETC.

AutoCAD SHX Text %%uCONTROL SYSTEM CONTRACTORS

AutoCAD SHX Text %%uGENERAL NOTES TO TEMPERATURE

AutoCAD SHX Text THE CONTROLS CONTRACTOR SHALL PROVIDE ALL ELECTRICAL POWER AND CONTROL WIRING, CONDUIT, JUNCTION BOXES, RACEWAY, TRANSFORMERS, RELAYS AND ALL OTHER ELECTRICAL APPURTENANCES REQUIRED FOR A COMPLETE AND FULLY OPERATIONAL CONTROL SYSTEM. THIS INCLUDES ALL POWER WIRING, FROM AN EMERGENCY SOURCE OF POWER (20 AMP BREAKER) IN THE THIRD FLOOR PROJECT AREA PROVIDED BY ELECTRICAL CONTRACTOR, FOR TEMPERATURE CONTROLS, CONTROL PANELS AND ALL OTHER TEMPERATURE CONTROL SYSTEM COMPONENTS.

AutoCAD SHX Text ALL ELECTRICAL WORK SHALL BE IN CONFORMANCE WITH THE LATEST NATIONAL ELECTRICAL CODE AND APPLICABLE STATE AND LOCAL AMENDMENTS.

AutoCAD SHX Text IN THE EVENT THAT ANY PART OF THE HEATING/VENTILATION DRAWINGS, SPECIFICATIONS OR NOTES CONFLICT WITH ANY OTHER: THE MOST STRINGENT REQUIREMENT SHALL APPLY, PROVIDING THE GREATEST SAFETY AND/OR AT THE HIGHEST COST OF THE CONFLICTING OPTIONS.

AutoCAD SHX Text THE CONTROLS CONTRACTOR SHALL INCLUDE ADEQUATE TIME IN HIS BID FOR COMPLETE COMMISSIONING OF THE MECHANICAL SYSTEMS, ON SITE IN COORDINATION WITH THE HEATING/VENTILATION CONTRACTOR AND OTHER TRADES AS REQUIRED TO MAKE ALL EQUIPMENT COMPLETE AND FULLY OPERATIONAL.

AutoCAD SHX Text THE CONTROLS CONTRACTOR SHALL PROVIDE ALL CONTROL VALVES AND ACTUATORS TO THE HEATING/VENTILATION CONTRACTOR FOR INSTALLATION. THE CONTROLS CONTRACTOR SHALL DIRECT THE HEATING/VENTILATION CONTRACTOR AS TO THE PROPER LOCATION AND ORIENTATION OF ALL DEVICES TO ACHIEVE A PROPER AND CORRECT CONTROL SEQUENCE.

AutoCAD SHX Text THE CONTROLS CONTRACTOR SHALL PROVIDE ALL CONTROL COMPONENTS, WIRING, INTERLOCKS, ELECTRICAL POWER, TUBING AND ALL OTHER DEVICES REQUIRED TO MAKE ALL HVAC EQUIPMENT INSTALLED UNDER THIS PROJECT COMPLETE AND FULLY OPERATIONAL PER THE SEQUENCE OF OPERATION AND AS REQUIRED FOR SAFE AND ACCURATE CONTROL.

AutoCAD SHX Text THE CONTROLS CONTRACTOR/ENGINEER SHALL IDENTIFY ANY POTENTIAL CONDITIONS THAT COULD BE CONSTRUED TO DEVIATE FROM GOOD CONTROLS ENGINEERING PRACTICE PRIOR TO BIDDING AND INCLUDE ALL ENGINEERING AND INSTALLATION WORK REQUIRED TO MAKE ALL HVAC SYSTEMS COMPLETE AND OPERATIONAL, IN CONFORMANCE WITH GOOD CONTROLS ENGINEERING PRACTICE: PRIOR TO SUBMITTING HIS BID.

AutoCAD SHX Text THE CONTROLS CONTRACTOR SHALL BE THE CONTROLS ENGINEER FOR THIS PROJECT: RESPONSIBLE FOR DESIGN AND ENGINEERING OF ALL CONTROL SYSTEMS TO OPERATE AS DESCRIBED IN THE SEQUENCE OF OPERATION, TO CONFORM WITH THE GOVERNING BUILDING CODES AND OPERATE IN A MANNER CONSISTENT WITH KNOWN GOOD CONTROLS ENGINEERING PRACTICE.

AutoCAD SHX Text

IV. THERMOSTATS

AutoCAD SHX Text

III. CONTROL VALVES

AutoCAD SHX Text

II. ELECTRICAL

AutoCAD SHX Text

I. GENERAL

AutoCAD SHX Text 17.

AutoCAD SHX Text THE VENTILATION CONTRACTOR TO PROVIDE FOR THE BALANCING OF THE VENTILATION SYSTEMS. THIS

AutoCAD SHX Text

INCLUDES ALL NEW AND EXISTING SUPPLY, RETURN AND EXHAUST DISTRIBUTION SYSTEMS.

AutoCAD SHX Text 18.

AutoCAD SHX Text THE HEATING CONTRACTOR TO PROVIDE FOR THE BALANCING OF THE HYDRONIC SYSTEMS. THIS INCLUDES

AutoCAD SHX Text

ALL NEW AND EXISTING HOT WATER HEATING AND CHILLED WATER DISTRIBUTION SYSTEMS.

AutoCAD SHX Text THE CONTROLS CONTRACTOR/ENGINEER SHALL FURNISH AND INSTALL MANUAL RESET SAFETY DEVICES FOR ANY AND ALL CONDITIONS THAT COULD DAMAGE THE EQUIPMENT AND/OR REPRESENT A THREAT TO HUMAN SAFETY. ALL WATER COILS SHALL BE PROTECTED BY AN AVERAGING ELEMENT FREEZE-STAT WITH A NON-ADJUSTABLE 40°F SET POINT. MANUAL RESETAND HARDWIRED INTERLOCK TO SHUT DOWN THE ASSOCIATED FAN ANY TIME THE TEMPERATURE ACROSS ANY 12" LENGTH OF THE AVERAGING ELEMENT FALLS BELOW 40°F. FREEZE STATS SHALL BE INSTALLED DOWNSTREAM OFALL WATER COILS. CONSTANT AIR VOLUME SYSTEMS HAVE A MANUAL RESET MAXIMUM DUCT STATIC PRESSURE SENSOR TO SHUT DOWN THE FAN ANY TIME DUCT STATIC PRESSURE RISES MORE THEN TWO INCHES WATER COLUMN ABOVE THE DESIGN OPERATING PRESSURE.

AutoCAD SHX Text

V. SAFETY DEVICES

AutoCAD SHX Text THE FACILITY HAS TWO PRIMARY BUILDING AUTOMATION SYSTEMS (BAS). THE FIRST IS METASYS BY JOHNSON CONTROL (JCI) AND THE SECOND IS TRIDIUM. ALL WORK ASSOCIATED WITH THIS PROJECT WILL BE INTEGRATED INTO THE TRIDIUM BAS. NO INTEROPERABILITY IS REQUIRED WITH THE EXISTING JCI BAS.

AutoCAD SHX Text THE ROOM THERMOSTAT SHALL MODULATE THE CAV BOX HOT WATER REHEAT COIL CONTROL VALVE TO MAINTAIN SETPOINT.

AutoCAD SHX Text

VI. ROOMS SERVED BY SUPPLY CAV BOX WITH HOT WATER REHEAT COIL CONTROL

AutoCAD SHX Text EXHAUST FAN TO BE START/STOP CONTROLLED VIA INTERFACE WITH THE EXISTING BUILDING AUTOMATION SYSTEM. THE FAN TO BE SCHEDULED TO OPERATE CONTINUOUSLY UNDER NORMAL BUILDING OPERATION. PROVIDE MONITORING OF THE EXHAUST FAN STATUS (ON/OFF) AT THE BAS. PROOF OF FAN OPERATION TO BE VIA A COMBINATION OF CURRENT SENSING RELAY AND DIFFERENTIAL PRESSURE SWITCH. WHEN THE FAN IS NOT OPERATING AT ITS COMMANDED STATUS (ON/OFF) AN ALARM WILL BE GENERATED AT THE BAS. TEMPERATURE CONTROL CONTRACTOR TO PROVIDE AUTOMATIC EXHAUST AIR DAMPER ACD-3 AND SHALL WIRE THE DAMPER TO OPEN/CLOSE WITH THE EXHAUST FAN ON/OFF. THE EXHAUST SYSTEM IS CONSTANT VOLUME. PROVIDE AIR MEASURING STATION AMS-3BIE IN THE EXHAUST DUCT MAIN. THE AIR MEASURING STATION TO MODULATE THE EXHAUST FAN VFD-EF3BIE IN ORDER TO MAINTAIN CONSTANT EXHAUST AIRFLOW AS THE EXHAUST SYSTEM FINAL FILTERS BECOME LOADED. PROVIDE MANUAL RESET DUCT STATIC PRESSURE SENSOR TO SHUT DOWN THE EXHAUST FAN SYSTEM ANY TIME THE DUCT STATIC PRESSURE RISES MORE THAN TWO INCHES WATER COLUMN ABOVE THE DESIGN OPERATING PRESSURE (AS MAY OCCUR DURING A FIRE DAMPER CLOSURE). THE EXHAUST AIRFLOW RATE TO BE MONITORED/ALARMED AT THE BUILDING AUTOMATION SYSTEM.

AutoCAD SHX Text

XI. EXHAUST FAN EF-3BIE CONTROL

AutoCAD SHX Text

REFER TO TEMPERATURE CONTROL DIAGRAM ON DRAWINGS

AutoCAD SHX Text

XIV. AIR HANDLING UNIT AHU-3B1 SYSTEM

AutoCAD SHX Text DURING SUMMER MODE OF OPERATION THE CONTROL VALVE SERVING THE RADIANT CEILING PANEL TO BE CLOSED. THE ROOM THERMOSTAT SHALL MODULATE THE CAV BOX HOT WATER REHEAT COIL CONTROL VALVE TO MAINTAIN SETPOINT.

AutoCAD SHX Text VII. ROOMS SERVED BY SUPPLY CAV BOX WITH HOT WATER REHEAT COIL CONTROL AND RADIANT

AutoCAD SHX Text PROVIDE ROOM PRESSURIZATION MONITOR/ALARM SYSTEMS (4-SUCH) TO MONITOR/ALARM THE DIFFERENTIAL PRESSURE BETWEEN VESTIBULE B3062 AND CORRIDOR B3100; VESTIBULE B3062 AND ISOLATION PATIENT ROOM B3062A; VESTIBULE B3064 AND CORRIDOR B3100; VESTIBULE B3064 AND ISOLATION PATIENT ROOM B3064A; VESTIBULE B3094 AND CORRIDOR B3100; VESTIBULE B3094 AND PROTECTIVE PATIENT ROOM B3094A; VESTIBULE B3098 AND CORRIDOR B3100; AND VESTIBULE B3098 AND PROTECTIVE PATIENT ROOM B3098A. THE SYSTEMS TO PROVIDE DIGITAL DISPLAY OF THE DIFFERENTIAL PRESSURE AND ALARM AT THE DISPLAY PANELS. THE ROOM PRESSURE TO BE MONITORED/ALARMED AT THE CENTRAL BUILDING AUTOMATION SYSTEM.

AutoCAD SHX Text

XIII. ROOM PRESSURIZATION MONITOR/ALARM SYSTEMS

AutoCAD SHX Text PROVIDE A NEW STANDALONE BACNET-COMPLIANT CONTROL SYSTEM TO SERVE THE WORK IN THIS PROJECT. THE GENERAL CONTRACTOR OF THIS PROJECT SHALL DIRECTLY HIRE THE CONTROL SYSTEM INTEGRATOR (SPECIFICATION DIVISION 25-INTEGRATED AUTOMATION) IN A SEPARATE CONTRACT FROM THE CONTRACT PROCURING THE CONTROLS CONTRACTOR ADMINISTERED BY SPECIFICATION…