S

M

M

GFI

SS

M

S S

M

S sc scsc

EMERGENCY

FUEL SHUT-OFF

PANEL 'OF'

MTS

A

RECEPT

REEL

SUMP

PUMP

SUMP

PUMP

AIR

COMPRESSOR

EXHAUST

FAN

D

FIRE/SECURITY PANEL

E

S

S

S

S S

S

SS SS

S

S S

S S

S SS SS

B C B

C

C

Br od he ad

R oa d, S ui te

Be th le he m , P

A

7-

P :6

.6

.5

F:

0.

1.

H an ov er En g.

co m

Be th le he m O ffi ce

9165.003

1. ALL LIGHTING, RECEPTACLES, SENSORS, EQUIPMENT, CONDUIT, AND

WIRING LOCATED ON THE CEILING SHALL BE REMOVED TO

ACCOMMODATE TRUSS REMOVAL.

2. ALL EXISTING 8'-0" LONG, CEILING MOUNTED LED LUMINAIRES SHALL BE

REMOVED FROM CEILING AND STORED FOR FUTURE RE-INSTALLATION

ON NEW CEILING.

3. REFER TO SHEET KEYNOTES FOR ADDITIONAL ITEMS FOR SALVAGE TO

BE RE-INSTALLED.

GENERAL NOTES

A. REMOVE EXISTING PANELBOARD, PVC CONDUIT, AND CONDUCTORS BACK

TO PANEL 'OF' TO ACCOMMODATE NEW TRUSS INSTALLATION.

B. SALVAGE EXIT SIGN, EMERGENCY BATTERY HEAD, AND EXTERIOR

EMERGENCY HEAD FOR RE-INSTALLATION.

C. EQUIPMENT TO REMAIN AND BE RE-CONNECTED TO UPON TRUSS

INSTALLATION.

D. ALL DEVICES IN OFFICE TO REMAIN.

E. ALTERNATE #1: REMOVE EXISTING MANUAL TRANSFER SWITCH.

SHEET KEYNOTES

Scale:1 3/16" = 1'-0"

DEMOLITION PLAN - POWER

0 8'4'2'1'

Scale:2 3/16" = 1'-0"

DEMOLITION PLAN - LIGHTING

0 8'4'2'1'

ED

-1

013. DEMOLITION SHALL BE PERFORMED IN AN ORDERLY FASHION. ALL

NECESSARY PRECAUTIONS SHALL BE TAKEN TO PROTECT EXISTING

FACILITIES FROM DAMAGE DURING CONSTRUCTION.

4. PROTECT ALL ITEMS TO REMAIN IN SERVICE FROM DAMAGE DURING

THE DEMOLITION OR REMOVAL PORTION OF THIS PROJECT.

5. THE CONTRACTOR SHALL REVIEW ALL ELECTRICAL DEMOLITION WORK

WITH THE OWNER PRIOR TO START OF DEMOLITION WORK.

GENERAL DEMOLITION NOTES

1. THE FOLLOWING DEFINITIONS APPLY TO THE WORK:

A. REMOVE: REMOVE AND LEGALLY DISPOSE OF ITEMS EXCEPT

THOSE INDICATED TO BE REINSTALLED, SALVAGED OR TO REMAIN

THE OWNER'S PROPERTY.

B. REMOVE AND SALVAGE: ITEMS INDICATED TO BE REMOVED AND

SALVAGED MUST BE COVERED, PROTECTED, AND RELOCATED TO

THE OWNER'S DESIGNATED STORAGE AREA. IDENTIFY CONTENTS

OF ALL REMOVED AND SALVAGED ITEMS.

C. REMOVE AND REINSTALL: REMOVE ITEMS INDICATED: CLEAN,

SERVICE AND OTHERWISE PREPARE THEM FOR REUSE; STORE AND

PROTECT THEM AGAINST DAMAGE. REINSTALL ITEMS IN THE SAME

LOCATIONS OR IN LOCATIONS INDICATED.

D. EXISTING TO REMAIN: PROTECT CONSTRUCTION INDICATED TO

REMAIN AGAINST DAMAGED AND SOILING DURING SELECTIVE

DEMOLITION. WHEN PERMITTED BY THE OWNER'S

REPRESENTATIVE, ITEMS MAY BE REMOVED TO A SUITABLE,

PROTECTED STORAGE LOCATION DURING SELECTIVE DEMOLITION

AND THEN CLEANED AND REINSTALLED IN THEIR ORIGINAL

LOCATIONS.

2. THE OWNER RESERVES THE RIGHT TO SALVAGE ANY ITEMS IDENTIFIED

TO BE REMOVED. AT THE BEGINNING OF DEMOLITION WORK THE

OWNER'S REPRESENTATIVE SHALL IDENTIFY ALL ITEMS TO BE

SALVAGED.

GENERAL DEMOLITION NOTES

AutoCAD SHX Text

BAY 4

AutoCAD SHX Text

BAY 3

AutoCAD SHX Text

BAY 2

AutoCAD SHX Text

BAY 1

AutoCAD SHX Text

BAY 5

AutoCAD SHX Text

BAY 6

AutoCAD SHX Text

BAY 7

AutoCAD SHX Text

BAY 6

AutoCAD SHX Text

BAY 7

AutoCAD SHX Text

GARAGE

AutoCAD SHX Text

GARAGE

AutoCAD SHX Text

GARAGE

AutoCAD SHX Text

GARAGE

AutoCAD SHX Text

REST ROOM

AutoCAD SHX Text

NEMA

AutoCAD SHX Text

NEMA

AutoCAD SHX Text T

AutoCAD SHX Text H

AutoCAD SHX Text F

AutoCAD SHX Text H

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text

HC

AutoCAD SHX Text

HC

AutoCAD SHX Text

NEMA

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text F

AutoCAD SHX Text F

AutoCAD SHX Text T

AutoCAD SHX Text F

AutoCAD SHX Text T

AutoCAD SHX Text H

AutoCAD SHX Text F

AutoCAD SHX Text F

AutoCAD SHX Text H

AutoCAD SHX Text

BAY 4

AutoCAD SHX Text

BAY 3

AutoCAD SHX Text

BAY 2

AutoCAD SHX Text

BAY 1

AutoCAD SHX Text

BAY 5

AutoCAD SHX Text

BAY 6

AutoCAD SHX Text

BAY 7

AutoCAD SHX Text

BAY 6

AutoCAD SHX Text

BAY 7

AutoCAD SHX Text

GARAGE

AutoCAD SHX Text

GARAGE

AutoCAD SHX Text

GARAGE

AutoCAD SHX Text

GARAGE

AutoCAD SHX Text

REST ROOM

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text THIS DOCUMENT IS THE PROPERTY OF HANOVER ENGINEERING ASSOCIATES, INC. ANY USE OF A COPY OF THIS DOCUMENT THAT DOES NOT CONTAIN AN ORIGINAL SEAL AND SIGNATURE IS STRICTLY PROHIBITED. THIS DOCUMENT IS NOT PUBLISHED AND ALL RIGHTS ARE RESERVED BY HANOVER ENGINEERING ASSOCIATES, INC. THIS PLAN HAS BEEN SEALED WITH EITHER A RED INK SEAL OR A CRIMP SEAL. IF NEITHER APPEARS ON THIS PLAN, POSSIBLE REPRODUCTIONS OR ALTERATIONS MAY HAVE BEEN MADE WITHOUT THE APPROVAL OR KNOWLEDGE OF THE SIGNATORY.

AutoCAD SHX Text

DATE

AutoCAD SHX Text

NO.

AutoCAD SHX Text

REVISIONS

AutoCAD SHX Text

PLAN TITLE:

AutoCAD SHX Text

PROJECT TITLE:

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text

PROJECT NO.

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

CHECKED BY:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

DATE:

AutoCAD SHX Text 01/14/25

AutoCAD SHX Text L22-24

AutoCAD SHX Text

TOWNSHIP MAINTENANCE FACILITY

AutoCAD SHX Text

LONGSWAMP TOWNSHIP BERKS COUNTY PENNSYLVANIA

AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text 02-11-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR PERMITS

AutoCAD SHX Text

102 LONGSDALE DRIVE BUILDING ADDITION

AutoCAD SHX Text

SEAL:

AutoCAD SHX Text 09-01-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR BIDDING

AutoCAD SHX Text

CJD

AutoCAD SHX Text

CRS

AutoCAD SHX Text

ELECTRICAL - DEMOLITION

B,B5-7

A,b B5-3

B,B5-7

B2,B5-7

A,f

OF-26

X,B5-3

C,B5-3

X,B5-3 X,B5-3X,B5-3

X,B5-3X,B5-3

S

S

S

S

A,b B5-3

A,b B5-3

A,b B5-3

A,b B5-3

A,b B5-3

A,b B5-3

A,b B5-3

X,a B5-5

X,a B5-5

X,a B5-5

X,a B5-5

X,a B5-5

X,a B5-5

S

S

S

X,c B5-5

X,c B5-5

X,c B5-5

X,c B5-5

PANEL 'B5'

S S

X B5-5

X B5-5

X,d

OF-22

X,d

OF-22

X,d

OF-22

X,d

OF-22

X,d

OF-22

X,d

OF-22

X,d

OF-22

X,d

OF-22

S

X,e

OF-4

S

X,e

OF-4

X,e

OF-4

X,e

OF-4

X,e

OF-4

S

A,f

OF-26

A,f

OF-26

A,f

OF-26

A,f

OF-26

A,f

OF-26

A,f

OF-26

A,f

OF-26

A,f

OF-26

A,f

OF-26

S

S

S

A,b B5-3

B,B5-7 B,B5-7B,B5-7

X X

X

A,b B5-3

B,B5-7 B,B5-7

B,B5-7B,B5-7

B2,B5-7

B3,B5-7

B3,B5-7

PANEL 'OF'

1. REFER TO SHEET E-601 FOR PANEL SCHEDULES.

2. REFER TO SHEET E-602 FOR SPECIFICATIONS.

GENERAL NOTES

1. EXISTING LUMINAIRE RELOCATED FROM BAY #3.

2. EXISTING LUMINAIRE RELOCATED FROM BAY #4.

3. EXISTING LUMINAIRE RELOCATED FROM BAY #5.

SHEET KEYNOTES

Br od he ad

R oa d, S ui te

Be th le he m , P

A

7-

.6

.5

F:

0.

1.

H an ov er En g.

co m

Be th le he m O ffi ce

9165.003

Scale:1 3/16" = 1'-0"

PROPOSED LIGHTING - PLAN

0 8'4'2'1'

LUMINAIRE SCHEDULE

TYPE MANUFACTURER CATALOG NUMBER LUMENS WATTAGE CCT CRI MOUNTING VOLTAGE RMK. DESCRIPTION

A LITHONIA FEM-L96-15000LM-IMAFD-WD-MVOLT-GZ10-40K-80CRI- 15,912 94 4,000 80 C,S 120 -- 8'-0" LED ENCLOSED AND GASKETED INDUSTRIAL

B LITHONIA WDGE2-LED-P3SW-30K-80CRI-VF-MOVLT-SRM-PIR1FC3V-DDBXD 2,000 23 3,000 80 W 120 4,5 LED ARCHITECTURAL WALL SCONCE W/ VISUAL COMFORT LENS, MOTION SENSOR/PHOTOCELL

B2 LITHONIA WDGE2-LED-P3SW-30K-80CRI-VW-MOVLT-SRM-PIR1FC3V-DDBXD 2,000 23 3,000 80 W 120 4,5 LED ARCHITECTURAL WALL SCONCE W/ VISUAL COMFORT LENS, MOTION SENSOR/PHOTOCELL

B3 LITHONIA WDGE2-LED-P5-30K-80CRI-VF-MOVLT-SRM-PE-DDBXD 6,000 48 3,000 80 W 120 4,6 LED ARCHITECTURAL WALL SCONCE W/ VISUAL COMFORT LENS, PHOTOCELL

C LITHONIA LHQM-S-W-RG-MVOLT-HO 2,855 37 - - W 120 2 LED EXIST SIGN W/ BATTERY BACK, EMERGENCY HEADS, HIGH OUTPUT BATTERY

C1 LITHONIA ELMRW-LP220L-DNAXD-T - 2.4 - - W 7.2 3 LED WET LOCATION EMERGENCY REMOTE TWIN HEAD

X EXISTING - - - - - - 120 1 EXISTING LUMINAIRE/DEVICE TO BE RELOCATED

MOUNTING LEGEND NOTES

C = CEILING R = RECESSED 1.) ALL LUMINAIRES SHALL BE PROVIDED WITH A MINIMUM 5 YEAR WARRANTY.

S = SURFACE P = PENDANT

W = WALL B = BOLLARD

T = TRACK AC= AIRCRAFT CABLE

REMARKS

1. RE-INSTALL AT SAME LOCATION UPON NEW TRUSS/CEILING INSTALLATION. CLEAN LENS AND INTERNAL LED AREA PRIOR TO RE-INSTALLATION.

2. CONNECT TO UNSWITCHED SOURCE OF LOCAL LIGHTING CIRCUIT.

3. CONNECT TO LOCAL EXIT SIGN.

4. CONNECT TO UNSWITCHED SOURCE OF CIRCUIT SHOWN.

5. MOUNT TOP OF LUMINAIRE AT 13'-6" A.F.F.

6. MOUNT TOP OF LUMINAIRE AT 18' A.F.F.

EL

-1

AutoCAD SHX Text 3a

AutoCAD SHX Text 3a

AutoCAD SHX Text 3b

AutoCAD SHX Text 3b

AutoCAD SHX Text 4c

AutoCAD SHX Text 3c

AutoCAD SHX Text 3c

AutoCAD SHX Text 3d

AutoCAD SHX Text 3e

AutoCAD SHX Text 3d

AutoCAD SHX Text 3e

AutoCAD SHX Text 3f

AutoCAD SHX Text 3f

AutoCAD SHX Text 4d

AutoCAD SHX Text 4f

AutoCAD SHX Text THIS DOCUMENT IS THE PROPERTY OF HANOVER ENGINEERING ASSOCIATES, INC. ANY USE OF A COPY OF THIS DOCUMENT THAT DOES NOT CONTAIN AN ORIGINAL SEAL AND SIGNATURE IS STRICTLY PROHIBITED. THIS DOCUMENT IS NOT PUBLISHED AND ALL RIGHTS ARE RESERVED BY HANOVER ENGINEERING ASSOCIATES, INC. THIS PLAN HAS BEEN SEALED WITH EITHER A RED INK SEAL OR A CRIMP SEAL. IF NEITHER APPEARS ON THIS PLAN, POSSIBLE REPRODUCTIONS OR ALTERATIONS MAY HAVE BEEN MADE WITHOUT THE APPROVAL OR KNOWLEDGE OF THE SIGNATORY.

AutoCAD SHX Text

DATE

AutoCAD SHX Text

NO.

AutoCAD SHX Text

REVISIONS

AutoCAD SHX Text

PLAN TITLE:

AutoCAD SHX Text

PROJECT TITLE:

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text

PROJECT NO.

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

CHECKED BY:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

DATE:

AutoCAD SHX Text 01/14/25

AutoCAD SHX Text L22-24

AutoCAD SHX Text

TOWNSHIP MAINTENANCE FACILITY

AutoCAD SHX Text

LONGSWAMP TOWNSHIP BERKS COUNTY PENNSYLVANIA

AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text 02-11-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR PERMITS

AutoCAD SHX Text

102 LONGSDALE DRIVE BUILDING ADDITION

AutoCAD SHX Text

SEAL:

AutoCAD SHX Text 09-01-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR BIDDING

AutoCAD SHX Text

CJD

AutoCAD SHX Text

CRS

ELECTRICAL - LIGHTING

PANEL 'B5'

S B5-1

S B5-4

S B5-2

S B5-2

S B5-1

S

OF-9

S

OF-9

OF-18

AIR

COMPRESSOR

OF-5

M

M

M

M

S

B5-10

NEMA 10-50R

B5-10

NEMA 10-50R B5-9,GFI,36"B5-9,GFI,36"

B5-9,GFI,36"

B5-9,GFI,36"

B5-9,GFI,36"

B5-11,GFI,36"

B5-11,GFI,36" B5-11,GFI,36" B5-11,GFI,36"

B5-11,GFI,36"

B5-13,GFI,36"

B5-8,GFI,36" B5-8,GFI,36"

B5-8,GFI,36"

B5-8,GFI,36"

B5-8, GFI,36"

B5-6,GFI,WP

M

M

M

M

B5-15 B5-15

B5-17 B5-17 B5-19

B5-19 OF-6

B5-16,GFI,36"

B5-14 B5-14 B5-14

OF-6

SS

S S S S

SSSSS

CORD REEL

OF-28,GFI,36" OF-28,GFI,36"

B5-11,GFI,36"

OF-28,GFI,36"

OF-28,GFI,36"

OF-28,GFI,36"B5-16,GFI,36"B5-16,GFI,36"

B5-16,GFI,36"

OF-4,GFI

OF-21,GFI OF-21,GFI

OF,GFI-23

OF-16,GFI

B5-18, GFI

B5-18, GFI

B5-18, GFI

OF-30,GFI

OF-30,GFI

B5-11,GFI,WP OF-28,GFI,WP

OF-28,

GFI,WP

sc sc sc

UH

UH

UH

UH

UH

UH

GARAGE DOOR OPENER (TYPICAL FOR 11)

B5-20,GFI,WP,36"

PANEL 'OF'

ATS-13

GENERATOR

1. REFER TO SHEET E-601 FOR PANEL SCHEDULES.

2. REFER TO SHEET E-602 FOR SPECIFICATIONS.

3. ALL EXISTING RECEPTACLES SHALL BE REPLACED WITH NEW

RECEPTACLES. WIRE AND CONDUIT SHALL BE UTILIZED TO THE

GREATEST EXTENT POSSIBLE.

GENERAL NOTES

1. PROVIDE HEAVY DUTY, NEMA-12, 2P.30A, 208VAC NON-FUSED DISCONNECT

SWITCH.

2. RE-CONNECT TO EXISTING CIRCUIT.

3. ALTERNATE #1: PROVIDE AUTOMATIC TRANSFER SWITCH AND GENERATOR.

REFER TO ONELINE DIAGRAM AND SPECIFICATIONS FOR MORE

INFORMATION. REFER TO SITE PLANS FOR EXACT GENERATOR LOCATION.

4. ALTERNATE #1: PROVIDE GENERATOR EMERGENCY SHUTDOWN MEANS AT

THIS LOCATION IN ACCORDANCE WITH NEC 445.18(C) AND NFPA 110.

EMERGENCY STOP SHALL BE READILY ACCESSIBLE, IDENTIFIED, AND

LOCATED OUTSIDE THE GENERATOR ENCLOSURE

SHEET KEYNOTES

Br od he ad

R oa d, S ui te

Be th le he m , P

A

7-

.6

.5

F:

0.

1.

H an ov er En g.

co m

Be th le he m O ffi ce

9165.003

Scale:1 3/16" = 1'-0"

PROPOSED POWER - PLAN

0 8'4'2'1'

EP

-1

FIRE ALARM/SECURITY

1. SECURE THE SERVICES OF LONGSWAMP TOWNSHIP'S FIRE ALARM

SYSTEM PROVIDER TO PROVIDE A COMPLETE AND OPERATING FIRE

ALARM SYSTEM.

SAH INCORPORATED.

JIM BUCCIAGLIA

50 S. MUSEUM ROAD

READING, PA 19607

610-372-8872

JIMB@SAHINC.COM

2. THE EXISTING FIRE ALARM PANEL (SAH) SHALL BE RETAINED IN THE

EXISTING OFFICE. ALL EXISTING DETECTORS SHALL BE REMOVED AND

RE-INSTALLED AT SAME LOCATIONS NEW DETECTORS SHALL BE

INSTALLED IN ADDITIONAL BAYS NOTED.

3. THE ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR ALL

OUTLET BOXES AND ACCESS PATHWAYS REQUIRED FOR THE FIRE

ALARM SYSTEM MODIFICATIONS WITHIN THE BUILDING.

4. ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE TO COORDINATE

WORK AND CONSTRUCTION SCHEDULE WITH SUBCONTRACTORS.

ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR A FINAL

COMPLETE AND OPERATING FIRE ALARM SYSTEM.

VIDEO CAMERA SYSTEM

1. SECURE THE SERVICES OF LONGSWAMP TOWNSHIP'S VIDEO CAMERA

SYSTEM PROVIDER TO PROVIDE A COMPLETE AND OPERATING VIDEO

CAMERA SYSTEM.

SAH INCORPORATED.

JIM BUCCIAGLIA

50 S. MUSEUM ROAD

READING, PA 19607

610-372-8872

JIMB@SAHINC.COM

2. THE EXISTING VIDEO CAMERA SYSTEM SHALL BE REMOVED AND

RETAINED FROM THE EXISTING BUILDING SCHEDULED FOR

RENOVATIONS. THE VIDEO CAMERA SYSTEM SHALL BE REINSTALLED IN

THE RENOVATED BUILDING. NEW CAMERAS SHALL BE ADDED TO THE

SYSTEM TO ACCOMMODATE THE NEW BUILDING ADDITION. THE

EXISTING CAMERAS SHALL BE RE-INSTALLED AT THE SAME RESPECTIVE

LOCATIONS.

3. THE ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR ALL

OUTLET BOXES AND ACCESS PATHWAYS REQUIRED FOR VIDEO

SECURITY SYSTEMS WITHIN THE BUILDING AND THE SITE. SINGLE GANG

OUTLET BOXES & 3/4" CONDUIT WITH CAT6A CABLING AND A

PULLSTRINGS SHALL BE PROVIDED FROM THE CAMERA LOCATION BACK

TO THE DATA CLOSET BUILDING. OUTLET BOX HEIGHTS (INCLUDING

FINAL LOCATION) AND ACCESS PATHWAY ROUTING SHALL BE

COORDINATED WITH THE OWNER, ARCHITECT, AND SYSTEM PROVIDER

PRIOR TO INSTALLATION. CONDUIT SIZE SHALL BE 3/4" IN BUILDINGS, 1"

UNDERGROUND UNLESS AN ALTERNATE SIZE IS INDICATED ON PLANS.

4. ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE TO COORDINATE

WORK AND CONSTRUCTION SCHEDULE WITH SUBCONTRACTORS. ALL

CAMERAS SHALL BE AIMED TO SATISFY OWNER. ELECTRICAL

CONTRACTOR SHALL BE RESPONSIBLE FOR A FINAL COMPLETE AND

OPERATING VIDEO CAMERA SYSTEM.

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text

NEMA 10-50R

AutoCAD SHX Text

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text F

AutoCAD SHX Text F

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text H

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text T

AutoCAD SHX Text THIS DOCUMENT IS THE PROPERTY OF HANOVER ENGINEERING ASSOCIATES, INC. ANY USE OF A COPY OF THIS DOCUMENT THAT DOES NOT CONTAIN AN ORIGINAL SEAL AND SIGNATURE IS STRICTLY PROHIBITED. THIS DOCUMENT IS NOT PUBLISHED AND ALL RIGHTS ARE RESERVED BY HANOVER ENGINEERING ASSOCIATES, INC. THIS PLAN HAS BEEN SEALED WITH EITHER A RED INK SEAL OR A CRIMP SEAL. IF NEITHER APPEARS ON THIS PLAN, POSSIBLE REPRODUCTIONS OR ALTERATIONS MAY HAVE BEEN MADE WITHOUT THE APPROVAL OR KNOWLEDGE OF THE SIGNATORY.

AutoCAD SHX Text

DATE

AutoCAD SHX Text

NO.

AutoCAD SHX Text

REVISIONS

AutoCAD SHX Text

PLAN TITLE:

AutoCAD SHX Text

PROJECT TITLE:

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text

PROJECT NO.

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

CHECKED BY:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

DATE:

AutoCAD SHX Text 01/14/25

AutoCAD SHX Text L22-24

AutoCAD SHX Text

TOWNSHIP MAINTENANCE FACILITY

AutoCAD SHX Text

LONGSWAMP TOWNSHIP BERKS COUNTY PENNSYLVANIA

AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text 02-11-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR PERMITS

AutoCAD SHX Text

102 LONGSDALE DRIVE BUILDING ADDITION

AutoCAD SHX Text

SEAL:

AutoCAD SHX Text 09-01-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR BIDDING

AutoCAD SHX Text

CJD

AutoCAD SHX Text

CRS

ELECTRICAL - POWER

1. UTILIZE EXISTING 2P.100A BREAKER FOR NEW PANEL 'B5' FEED.

2. REMOVE EXISTING PANEL 'EPP', PANEL FEEDER TO PANEL 'OF', AND ALL

BRANCH CIRCUITS.

3. ALTERNATE #1: PROVIDE ALL COST ASSOCIATED WITH ADD ALTERNATE

NO.1 FOR A BACKUP GENERATOR. REMOVE EXISTING MANUAL TRANSFER

SWITCH AND PROVIDE NEW AUTOMATIC TRANSFER SWITCH. PROVIDE NEW

GENERATOR, CONCRETE PAD, CONNECTION TO EXISTING PROPANE TANK,

AND ALL ASSOCIATED APPURTENANCES REQUIRED FOR A COMPLETE

OPERATING AND CODE COMPLAINT BACKUP GENERATOR SYSTEM.

COORDINATE WITH UTILITY COMPANY.

4. ALTERNATE #1: PROVIDE TWO 1P.20A BREAKER IN EXISTING PANEL FOR

BACKUP GENERATOR SHORE POWER. CONFIRM VOLTAGE AND AMPERAGE

REQUIREMENTS WITH MANUFACTURER.

SHEET KEYNOTES

Scale:1 none

EXISTING ONE-LINE DIAGRAM

Br od he ad

R oa d, S ui te

Be th le he m , P

A

7-

.6

.5

F:

0.

1.

H an ov er En g.

co m

Be th le he m O ffi ce

9165.003

PANEL

"EPP"

125A

240/120V, 1Ø,3W

MLO.

12 CKT.

BAY #5

PANEL

"OF"

200A

240/120V, 1Ø,3W

200A MCB.

30 CKT.

BAY #1 OFFICE

100A

PLUG FOR

TEMP

GENERATOR

200A SIEMENS

MANUAL

TRANSFER

SWITCH (MTS)

MET -ED

METER #

5-001-403-3337

MET -ED

POLE #

58299-43008

EXISTING PANEL SCHEDULE "OF" (TO REMAIN)

CKT # LOAD DESCRIPTION

FEEDER

GRD COND. AMPS POLE

WATTS PER PHASE

POLE AMPS COND. GRD

FEEDER

LOAD DESCRIPTION CKT #

QTY SIZE A B A B SIZE QTY

1 PANEL 'EPP' 3 3 8 1 100 2 0 1 20 3/4 12 12 2 #5 LTS/REC, EXT LTS5/6, CLOCK REC3/4 2

3 - - - 500 1 20 3/4 12 12 2 #1 LIGHTS&REC , OUTSIDE CORNER LT 4

5 COMPRESSOR 2 10 10 3/4 30 2 3360 480 1 20 3/4 12 12 2 #1 GARAGE DOOR 6

7 - - - 3360 250 1 20 3/4 12 12 2 DOOR RECEPT, LIGHTS IN OFFICE 8

9 GAS HEATERS 2 12 12 3/4 20 1 1620 720 1 20 3/4 12 12 2 FUEL PUMPS 10

11 BASEBOARD HEAT 2 12 12 3/4 20 2 1000 180 1 20 3/4 12 12 2 RECEPT AT DESK 12

13 - - - 1000 0 1 20 3/4 12 12 2 ASH SHED 14

15 OFFICE FAN & #4 RECEPT 2 12 12 3/4 20 1 360 300 1 15 3/4 12 12 2 SHOP FAN #1 16

17 WATER PUMP 2 12 12 3/4 15 2 960 3600 2 50 3/4 10 8 2 WELDER RECEPT 18

19 - - - 960 3600 - - - 20

21 WORK BENCH RECEPT & LIGHTS 2 12 12 3/4 20 1 180 800 1 20 3/4 12 12 2 LIGHTS #2, #3, #4 22

23 WATER HEATER & RECEPT 2 12 12 3/4 20 1 1200 180 1 20 3/4 12 12 2 PANEL RECEPT 24

25 GENERATOR BATTERY CHARGER 2 12 12 1 20 1 600 970 1 20 3/4 12 12 2 LIGHTS BAY 1,2,3,4 WEST ** 26

27 GENERATOR HEATER 2 12 12 1 20 1 1200 900 1 20 3/4 12 12 2 RECEPT BAY 1 WEST ** 28

29 SPACE 360 1 20 3/4 12 12 2 RECEPT BAY 1/2 COMMON WALL ** 30

TOTAL WATTS PER PHASE 7720 8080 6930 5910

TOTAL A Ø WATTS 14650 TOTAL A Ø AMPS 122.08 VOLTAGE: 120/ 240V 1P, 3W LOCATION: UTILITY 100, PUMP HS NOTES: EXISTING SIEMENS SERIES 'E' PANEL.

NEMA TYPE 1.

TOTAL C Ø WATTS 13990 TOTAL C Ø AMPS 116.58 AMPACITY: 200 MAIN BREAKER: BREAKER

AIC RATING: 10,000 MOUNTING: SURFACE

TOTAL 1 Ø WATTS 28640 TOTAL 1 Ø AMPS 119.33 FED FROM MET-ED SERVICE VIA MANUAL TRANSFER SWITCH

REMARKS: ** PROVIDE SIEMENS 1P.20A TYPE 'QP' BREAKER

EXISTING PANEL SCHEDULE "EPP" (SCHEDULED FOR DEMOLITION)

CKT # LOAD DESCRIPTION

FEEDER

GRD COND. AMPS POLE

WATTS PER PHASE

POLE AMPS COND. GRD

FEEDER

LOAD DESCRIPTION CKT #

QTY SIZE A B A B SIZE QTY

1 GAS HEATER BAY 6 15 1 180 798 1 15 - 2

3 - 20 1 180 627 1 15 - 4

5 - 20 1 180 267 1 15 EXTERIOR OUTLETS 6

7 SPACE 1 360 0 1 20 INTERIOR OUTLETS 8

9 - 15 1 180 0 2 50 WASHING COMPRESSOR OUTLETS 10

11 GARAGE OUTLETS 20 1 180 960 - - 12

TOTAL WATTS PER PHASE 540 720 1065 1587

TOTAL A Ø WATTS 1605 TOTAL A Ø AMPS 13.38 VOLTAGE: 120/ 240V 1P, 3W LOCATION: BAY #5 NOTES: EXISTING CROUSE-HINDS TYPE 'F'

PANEL. NEMA TYPE 1.

TOTAL C Ø WATTS 2307 TOTAL C Ø AMPS 19.23 AMPACITY: 125 MAIN BREAKER: LUG

AIC RATING: 10,000 MOUNTING: SURFACE

TOTAL 1 Ø WATTS 3912 TOTAL 1 Ø AMPS 16.30 FED FROM PANEL 'OF'

REMARKS:

E-

PROPOSED PANEL SCHEDULE "B5"

CKT # LOAD DESCRIPTION

FEEDER

GRD COND. AMPS POLE

WATTS PER PHASE

POLE AMPS COND. GRD

FEEDER

LOAD DESCRIPTION CKT #

QTY SIZE A B A B SIZE QTY

1 GAS HEATERS BAY 6 & 7 2 12 12 3/4 20 1 1620 1620 1 20 3/4 12 12 2 GAS HEATERS BAY 4 2

3 LIGHTS BAY 5, 6, 7 WEST 2 12 12 3/4 20 1 970 810 1 20 3/4 12 12 2 GAS HEATER BAY 5 4

5 LIGHTS BAY 5, 6, 7 EAST 2 12 12 3/4 20 1 800 180 1 20 3/4 12 12 2 EXTERIOR OUTLETS 6

7 LIGHTS EXTERIOR 2 12 12 3/4 20 1 206 900 1 20 3/4 12 12 2 RECEPT BAY 5 8

9 RECEPT BAY 6&7 EAST 2 12 12 3/4 20 1 900 3600 2 50 3/4 10 8 2 WASHING COMPRESSOR OUTLETS 10

11 RECEPT BAY 5,6&7 WEST 2 12 12 3/4 20 1 900 3600 - - 12

13 RECEPT BAY 5 AT PANEL B5 2 12 12 3/4 20 1 180 900 1 20 3/4 12 12 2 GARAGE DOORS 2,3, & 4 EAST 14

15 GARAGE DOORS 6 & 7 EAST 2 12 12 3/4 20 1 900 720 1 20 3/4 12 12 2 RECEPT BAY 2,3,4 WEST 16

17 GARAGE DOORS 6 & 7 WEST 2 12 12 3/4 20 1 900 900 1 20 3/4 12 12 2 RECEPT BAY 2,3,4 EAST 18

19 GARAGE DOORS BAY 5 2 12 12 3/4 20 1 900 180 1 20 3/4 12 12 2 RECEPT EXTERIOR SOUTH 20

21 SPARE 20 1 1 20 SPARE 22

23 SPARE 20 1 1 20 SPARE 24

25 SPARE 20 1 1 20 SPARE 26

27 SPARE 20 1 1 20 SPARE 28

29 SPARE 20 1 1 20 SPARE 30

TOTAL WATTS PER PHASE 4400 3876 7200 6210

TOTAL A Ø WATTS 11600 TOTAL A Ø AMPS 96.67 VOLTAGE: 120/ 240V 1P, 3W LOCATION: BAY #5 NOTES: BASIS OF DESIGN SQUARE-D NQ, NEMA

TYPE 12. TURN OFF ALL SPARE BREAKERS

TOTAL C Ø WATTS 10086 TOTAL C Ø AMPS 84.05 AMPACITY: 100 MAIN BREAKER: LUG

AIC RATING: 10,000 MOUNTING: SURFACE

TOTAL 1 Ø WATTS 21686 TOTAL 1 Ø AMPS 90.36 FED FROM PANEL 'OF' IN OFFICE (BAY #1)

REMARKS:

Scale:2 none

PROPOSED ONE-LINE DIAGRAM

PANEL

"B5" 100A

240/120V, 1Ø,3W

MLO.

30 CKT.

BAY #5

PANEL

"OF"

200A

240/120V, 1Ø,3W

200A MCB.

30 CKT.

BAY #1 OFFICE

100A

MET -ED

METER #

5-001-403-3337

MET -ED

POLE #

58299-43008

3#3 & 1 #8GRD.,

1" EMT CONDUIT

1. ALL BRANCH CIRCUIT WIRING SHALL BE COPPER, THWN, 2#12 & 1#12

GRD., 3/4" CONDUIT, 1" CONDUIT UNDERGROUND (PVC) OR WITHIN

FLOOR, UNLESS NOTED OTHERWISE. PROVIDE SEPARATE NEUTRALS

AND SEPARATE GREEN INSULATED EQUIPMENT GROUNDING

CONDUCTORS FOR ALL FEEDER AND BRANCH CIRCUITS. TERMINATE

EACH GROUNDING CONDUCTOR ON A GROUNDING LUG, BUS, OR

BUSHING. ALL BRANCH CIRCUIT WIRING IS SHOWN DIAGRAMMATICALLY,

CONTRACTOR SHALL COORDINATE ACTUAL CIRCUIT ROUTING WITH

OTHER TRADES AND BUILDING CONSTRUCTION.

2. SEAL ALL CONDUIT PENETRATIONS THROUGH WALLS WITH

APPROPRIATE SEALANT. PENETRATIONS THROUGH FIRE RATED WALLS

AND FLOORS SHALL BE SEALED WITH A FIRE RATED SEALANT THAT IS

EQUAL OR BETTER THAN THE FIRE RATED MATERIAL THROUGH WHICH IT

PASSES.

3. ALL NEW WIRING SHALL BE ROUTED CONCEALED WITHIN NEW WALLS OR

CEILING SPACE. WIRING ON EXISTING WALLS SHALL BE SURFACE

MOUNTED RACEWAY. PROVIDE PULL BOXES AT LOCATIONS NEEDED,

AND ADEQUATELY SIZED AS REQUIRED FOR THE EQUIPMENT SERVED.

4. CONTRACTOR SHALL COORDINATE ALL ELECTRICAL EQUIPMENT/DEVICE

REQUIREMENTS FOR EQUIPMENT PROVIDED BY OTHERS. CONTRACTOR

SHALL BE RESPONSIBLE FOR ALL ASSOCIATED EQUIPMENT &

TERMINATIONS TO EQUIPMENT IN ACCORDANCE WITH MANUFACTURER'S

REQUIREMENTS.

5. COORDINATE ALL POWER OUTAGES WITH THE OWNER PRIOR TO START

OF WORK. PROVIDE TEMPORARY POWER FOR BUILDING SERVICE,

CRITICAL LOADS, LIGHTING AND MISCELLANEOUS POWER

REQUIREMENTS FOR THE CONSTRUCTION AREA. PROVIDE GROUND

FAULT PROTECTION FOR TEMPORARY POWER. TEMPORARY FEEDER

AND BRANCH CIRCUIT CONDUIT & WIRING SHALL BE PROVIDED TO KEEP

CRITICAL LOADS OPERATIONAL DURING CONSTRUCTION. TEMPORARY

CONDUIT & WIRING SHALL MATCH EXISTING CONDUIT & WIRING

CURRENTLY SERVING CRITICAL LOADS IN ACCORDANCE WITH NEC

REQUIREMENTS.

6. ALL EQUIPMENT SHALL BE PROPERLY GROUNDED AND BONDED, AND

SHALL MEET THE REQUIREMENTS OF BOTH THE NATIONAL ELECTRICAL

CODE (ARTICLE 250), AND THE EQUIPMENT/SYSTEM MANUFACTURER'S

REQUIREMENTS FOR TYPES, SIZES, AND QUANTITIES OF EQUIPMENT

GROUNDING CONDUCTORS, EXCEPT WHERE SPECIFIC TYPES, LARGER

SIZES, OR MORE CONDUCTORS THAN REQUIRED BY NEC ARE INDICATED.

7. INSTALLATION OF ALL LUMINAIRES SHALL BE COORDINATED WITH THE

ARCHITECT AND MANUFACTURER'S REQUIREMENTS PRIOR TO

INSTALLATION. CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING

ALL NECESSARY MOUNTING & SUPPORT HARDWARE FOR A COMPLETE &

WORKING INSTALLATION.

8. THE CONTRACTOR SHALL VERIFY DIMENSIONS AND EXISTING

CONDITIONS PRIOR TO THE START OF THE WORK, NOTIFY THE

ENGINEER OF ANY SIGNIFICANT CHANGES IN DIMENSIONS AND

CONDITIONS.

9. THE CONTRACTOR SHALL PROVIDE ALL MATERIALS, TOOLS, EQUIPMENT,

AND NECESSARY FACILITIES, AND PERFORM ALL LABOR AND SERVICES

OF EVERY DESCRIPTION AS MAY BE NECESSARY TO COMPLETE THE

SCOPE OF THE WORK DEFINED IN THE CONTRACT DOCUMENTS.

10. FABRICATE AND INSTALL ALL WORK IN STRICT ACCORDANCE WITH THE

NATIONAL ELECTRICAL CODE (NEC), THE NATIONAL ELECTRICAL SAFETY

CODE (NESC), NATIONAL FIRE PROTECTION ASSOCIATION (NFPA),

INTERNATIONAL BUILDING CODE (IBC), AMERICANS WITH DISABILITIES

ACT (ADA), NECA STANDARD OF INSTALLATION, OSHA, ALL APPLICABLE

STATE AND LOCAL CODES, GENERAL CONDITIONS AND SUPPLEMENTAL

TERMS OF THE CONTRACT. ALL EQUIPMENT SHALL BE UNDERWRITERS

LABORATORIES (U.L.) LISTED FOR ITS APPLICATION WHERE SUCH ITEMS

ARE REQUIRED.

11. ALL CONTRACTORS AND SUB-CONTRACTORS SHALL BE RESPONSIBLE

FOR THE PROPER PERFORMANCE OF THEIR WORK, COORDINATION WITH

OTHER TRADES, MEANS AND METHODS OF CONSTRUCTION, AND

SAFETY AND SECURITY WHILE ON SITE.

12. PROTECT EXISTING PROPERTY DURING CONSTRUCTION. REPAIR OR

REPLACE, WITHOUT ADDITIONAL CHARGE TO THE OWNER, ANY EXISTING

WORK DAMAGED DURING THE COURSE OF CONSTRUCTION.

13. THE CONTRACT DRAWINGS ARE DIAGRAMMATIC AND ARE INTENDED TO

CONVEY, IN A GENERAL WAY, THE SCOPE OF THE WORK. THEY ARE NOT

INTENDED TO ILLUSTRATE ALL CONDITIONS WHICH MAY BE

ENCOUNTERED AT THE SITE.

14. REFER TO ARCHITECTURAL BUILDING PLANS FOR PROPER DIMENSIONS.

15. PUSH-ON WIRE CONNECTORS, OTHER THAN FOR LUMINAIRE

DISCONNECTS, SHALL NOT BE ALLOWED.

16. ALL GENERAL USE RECEPTACLES SHALL BE INSTALLED AT HEIGHTS

NOTED ABOVE FINISHED FLOOR AND SHALL BE RATED 20A, 125V, NEMA

5-20R, U.L. LISTED, UNLESS NOTED OTHERWISE. COORDINATE LOCATION

OF RECEPTACLES WITH OTHER DEVICES AND TELECOMMUNICATIONS

OUTLETS IN ROOM. SPECIFIC EQUIPMENT & DEVICE RECEPTACLE

MOUNTING HEIGHTS WITH EQUIPMENT & DEVICES TO BE INSTALLED.

(EXAMPLE: PROJECTORS AND AUDIO/VISUAL EQUIPMENT)

17. THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL CUTTING AND

PATCHING ASSOCIATED WITH THE INSTALLATION AND REMOVAL OF

ELECTRICAL EQUIPMENT.

18. CIRCUIT BREAKERS PROVIDED WITHIN EXISTING PANELBOARDS SHALL

BE COMPATIBLE WITH PANELBOARD AND SHALL HAVE THE

INTERRUPTING CAPACITY TO MEET THE AVAILABLE FAULT CURRENTS OF

THE EXISTING EQUIPMENT.

19. RECEPTACLE LABELING: ALL RECEPTACLES SHALL BE LABELED WITH

SELF-ADHESIVE CLEAR LABELS WITH 3/32” BLACK LETTERING ON THE FRONT

COVERPLATE OF THE RECEPTACLE. RECEPTACLE LABELING SHALL IDENTIFY

PANEL NAME AND CIRCUIT NUMBER FROM WHERE IT IS SERVED (EXAMPLE:

B5-13).

20. PROVIDE A POWER SYSTEM STUDY CONSISTING OF SHORT CIRCUIT,

EQUIPMENT DUTY, COORDINATION, AND ARC FLASH HAZARDS

ANALYSES FOR ALL ELECTRICAL DISTRIBUTION EQUIPMENT. THE

CONTRACTOR IS RESPONSIBLE TO OBTAIN ALL DATA NECESSARY FOR

PROPER COMPLETION OF THE STUDIES.

21. THE CONTRACTOR IS RESPONSIBLE TO PROVIDE COMPLETELY

COORDINATED EQUIPMENT. ALL EQUIPMENT MUST BE ADEQUATELY

RATED FOR THE AVAILABLE FAULT CURRENTS AT THE INSTALLATION

LOCATION. ENSURE POWER SYSTEM STUDY AND SHOP DRAWINGS FOR

ELECTRICAL DISTRIBUTION EQUIPMENT ARE SUBMITTED AT THE SAME

TIME FOR REVIEW BY THE ENGINEER OF RECORD.

22. PROVIDE A LABEL ON ALL SERVICE EQUIPMENT STATING THE MAXIMUM

AVAILABLE FAULT CURRENT AS CALCULATED BY THE POWER SYSTEM

STUDY. THE LABEL SHALL ALSO DISPLAY THE DATE THE CALCULATION

WAS PERFORMED.

GENERAL ELECTRICAL NOTES

LEGEND

LUMINAIRE, TYPE AS INDICATED ON PLAN. REFER TO EL-101

FOR SCHEDULE CONNECT TO CIRCUITS SHOWN ON PLAN.A,b

LUMINAIRE TYPE

SWITCHING ZONE, IF NONE CONNECT TO ALL

LUMINAIRES IN THE ROOM

B5-# PANEL-CIRCUIT NUMBER

IN-WALL, SINGLE POLE SWITCH

IN-WALL, THREE-WAY SWITCHS

S

EXISTING WALL MOUNTED EXIT SIGN

PROVIDE NEW 20A, 120VAC, DUPLEX RECEPTACLE, HEAVY DUTY

SPECIFICATION GRADE, NEMA 5-20R. PROVIDE TYPED LABEL ON

EACH RECEPTACLE COVERPLATE W/PANELBOARD NAME AND

CIRCUIT NUMBER. SAMPLE 'B5-5'. CLEAR LABEL W/ BLACK

LETTER, 3/32" HIGH. CONNECT TO CIRCUIT SHOWN.

PROVIDE NEW NEMA TYPE RECEPTACLE SHOWN, PROVIDE NEMA

TYPE RECEPTACLE AS NOTED ON PLAN VIEW. PROVIDE TYPED

LABEL ON EACH RECEPTACLE COVERPLATE W/PANELBOARD

NAME AND CIRCUIT NUMBER. CLEAR LABEL W/ BLACK LETTER,

3/32" HIGH. CONNECT TO CIRCUIT SHOWN.

NEMA #-##R,

NO DENOTE = NEW OUTLET AT 18",

AC = NEW OUTLET, MOUNT 8" ABOVE COUNTER TOP

##" = HEIGHT ABOVE FINISH FLOOR

GFI = GROUND FAULT CIRCUIT INTERRUPTER.

WP = WEATHER-RESISTANT W/ INTEGRAL GROUND FAULT

CIRCUIT INTERRUPTER MOUNTED IN LOCKABLE, WATER

PROOF WHILE IN USE ENCLOSURE. INTERMATIC MODEL

#WP1010HMC, OR APPROVED EQUAL.

EXISTING EMERGENCY BATTERY PACK

EXISTING EMERGENCY HEAD

IN-WALL, FOUR-WAY SWITCHS

FRACTIONAL HORSEPOWER MANUAL STARTER W/ RED PILOT

LIGHT, ONE POLE FOR 120 VOLT CIRCUIT, TWO POLE FOR 208 VOLT

CIRCUIT. PROPERLY SIZE CLASS 20 OVERLOAD AT 125%

OF FULL LOAD AMP OF EQUIPMENT.

S

CEILING MOUNTED RECEPTACLE

WIRED GARAGE DOOR OPERATOR

MOTOR, # = HORSEPOWER, F = FRACTIONAL

EXISTING DEVICE (SHOWN DASHED) TO BE REMOVED/SALVAGED/DEMO

EXISTING DEVICE (SHOWN LIGHT) TO REMAIN/REINSTALLED

PROVIDE NEW DEVICE/EQUIPMENT (SHOWN RED)

SWITCHING ZONE, IF NONE CONNECT TO ALL

LUMINAIRES IN THE ROOM

sc SECURITY CAMERA

MOTION SENSOR

HEAT DETECTOR

M

G

ATS-1, NEW INTERIOR TYPE 1,

120/240V,1P,3W, 200A, 3 POLE, SERVICE

ENTRANCE RATED, ATS DESIGN BASIS:

GENERAC:TX301, OR APPROVED EQUAL. 200A

3#3/0 & 1#4

GRD., 2" C.

200A

3#3/0 & 1#4

GRD., 2" C.

AutoCAD SHX Text THIS DOCUMENT IS THE PROPERTY OF HANOVER ENGINEERING ASSOCIATES, INC. ANY USE OF A COPY OF THIS DOCUMENT THAT DOES NOT CONTAIN AN ORIGINAL SEAL AND SIGNATURE IS STRICTLY PROHIBITED. THIS DOCUMENT IS NOT PUBLISHED AND ALL RIGHTS ARE RESERVED BY HANOVER ENGINEERING ASSOCIATES, INC. THIS PLAN HAS BEEN SEALED WITH EITHER A RED INK SEAL OR A CRIMP SEAL. IF NEITHER APPEARS ON THIS PLAN, POSSIBLE REPRODUCTIONS OR ALTERATIONS MAY HAVE BEEN MADE WITHOUT THE APPROVAL OR KNOWLEDGE OF THE SIGNATORY.

AutoCAD SHX Text

DATE

AutoCAD SHX Text

NO.

AutoCAD SHX Text

REVISIONS

AutoCAD SHX Text

PLAN TITLE:

AutoCAD SHX Text

PROJECT TITLE:

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text

PROJECT NO.

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

CHECKED BY:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

DATE:

AutoCAD SHX Text 01/14/25

AutoCAD SHX Text L22-24

AutoCAD SHX Text

TOWNSHIP MAINTENANCE FACILITY

AutoCAD SHX Text

LONGSWAMP TOWNSHIP BERKS COUNTY PENNSYLVANIA

AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text 02-11-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR PERMITS

AutoCAD SHX Text

102 LONGSDALE DRIVE BUILDING ADDITION

AutoCAD SHX Text

SEAL:

AutoCAD SHX Text 09-01-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR BIDDING

AutoCAD SHX Text

CJD

AutoCAD SHX Text

CRS

AutoCAD SHX Text

ELECTRICAL-ONELINE & SCHEDULES

AutoCAD SHX Text

AutoCAD SHX Text 4,b

AutoCAD SHX Text T

AutoCAD SHX Text F

H

Br od he ad

R oa d, S ui te

Be th le he m , P

A

7-

.6

.5

F:

0.

1.

H an ov er En g.

co m

Be th le he m O ffi ce

9165.003

E-

16.1 GENERAL DESCRIPTION

1. PLANS AND SPECIFICATIONS

A. THE PLANS AND SPECIFICATIONS ARE CONTRACT BID DOCUMENTS, AND ARE FOR THE PURPOSE OF ILLUSTRATING THE GENERAL CHARACTER AND SCOPE OF WORK FOR CONTRACTORS TO PREPARE A BID PROPOSAL. THE PLANS ARE NOT SHOP DRAWINGS AND DO NOT DISMISS THE CONTRACTOR FROM THE RESPONSIBILITY OF PREPARING FABRICATION AND INSTALLATION SHOP DRAWINGS, NOR DO THEY RELIEVE THE CONTRACTOR FROM THE RESPONSIBILITY OF COORDINATING WITH THE WORK OF OTHER TRADES AND THE BUILDING

STRUCTURE.

2. SUBMITTALS

A. COORDINATION: COORDINATE PREPARATION AND PROCESSING OF SUBMITTALS WITH PERFORMANCE OF CONSTRUCTION ACTIVITIES.

TRANSMIT EACH SUBMITTAL SUFFICIENTLY IN ADVANCE OF PERFORMANCE OF RELATED CONSTRUCTION ACTIVITIES TO AVOID DELAY.

B. SUBMITTAL PREPARATION: PLACE A PERMANENT LABEL OR TITLE BLOCK ON EACH SUBMITTAL FOR IDENTIFICATION. INDICATE THE NAME

OF THE ENTITY THAT PREPARED EACH SUBMITTAL ON THE LABEL OR TITLE BLOCK.

C. COLLECT PRODUCT DATA INTO A SINGLE SUBMITTAL FOR EACH ELEMENT OF CONSTRUCTION OR SYSTEM. PRODUCT DATA INCLUDES PRINTED INFORMATION, SUCH AS MANUFACTURER'S INSTALLATION INSTRUCTIONS, CATALOG CUTS, STANDARD COLOR CHARTS, ROUGHING-IN DIAGRAMS AND TEMPLATES, STANDARD WIRING DIAGRAMS, AND PERFORMANCE CURVES. WHERE PRODUCT DATA MUST BE SPECIALLY PREPARED BECAUSE STANDARD PRINTED DATA IS NOT SUITABLE FOR USE, SUBMIT AS "SHOP DRAWINGS." SUBMIT PRODUCT

DATA FOR THE FOLLOWING:

1) LIGHTING LUMINAIRES

2) LIGHTING CONTROLS

3) WIRING DEVICES

4) PANELBOARDS

5) WIRE AND CABLE

6) CONDUIT RACEWAYS

D. SUBMIT OPERATION AND MAINTENANCE DATA FOR EACH TYPE OF PRODUCT SPECIFIED IN 1) TO 6) ABOVE FOR INCLUSION IN AN OPERATION

AND MAINTENANCE MANUAL.

E. INCLUDE FM GLOBAL DATA SHEETS FOR EQUIPMENT.

F. RECORD DRAWINGS: SUBMIT TWO COPIES OF AS-BUILT DRAWINGS.

3. WARRANTY

A. THE CONTRACTOR SHALL UNCONDITIONALLY GUARANTEE, IN WRITING, ALL WORK, ARTICLES, APPLIANCES, MATERIALS, EQUIPMENT, AND WORKMANSHIP FURNISHED, INSTALLED, OR SUPPLIED UNDER THIS CONTRACT FOR A PERIOD OF ONE YEAR FROM THE DATE OF

ACCEPTANCE BY THE OWNER.

B. THE CONTRACTOR SHALL ADJUST, REPAIR, OR REPLACE ANY DEFECTIVE PART OF THE SYSTEM WITHOUT COST TO THE OWNER.

4. CODES AND STANDARDS

A. PROVIDE EQUIPMENT AND INSTALLATION IN ACCORDANCE WITH THIS SPECIFICATION AND APPLICABLE REQUIREMENTS OF THE FOLLOWING:

a. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)

b. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)

c. AMERICANS WITH DISABILITIES ACT (PUBLIC LAW 101-336)

d. AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME)

e. NATIONAL ELECTRICAL CODE (NEC)

f. OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA)

g. UNDERWRITERS LABORATORIES INC. (UL)

h. NATIONAL FIRE PROTECTION ASSOCIATION: NATIONAL FIRE CODES (NFPA)

i. IBC 2018, ALL LOCAL CODES AND ORDINANCES

B. THE CONTRACTOR SHALL OBTAIN ALL PERMITS, LICENSES, AND APPROVALS WITH THE DEPARTMENTS HAVING JURISDICTION, PAY ALL CHARGES AND FEES, FILE ALL NECESSARY PLANS, AND GIVE ALL NOTICES NECESSARY AND INCIDENT TO DO THE LAWFUL PROSECUTION OF THE WORK. CONTRACTOR SHALL OBTAIN AND FURNISH TO THE OWNER ALL CERTIFICATES FOR WORK FOR WHICH CERTIFICATES ARE REQUIRED. THE CONTRACTOR SHALL PAY FOR ALL STATE, COUNTY, BOROUGH, AND TOWNSHIP FEES, PERMITS, LICENSES, LAWS, AND/OR OTHER FEES WHICH MAY BE REQUIRED IN THE PERFORMANCE OF HIS CONTRACT AND NOT OTHERWISE PROVIDED FOR.

16.2 CONDUIT

1. ELECTRICAL METALLIC TUBING SHALL BE GALVANIZED STEEL MEETING REQUIREMENTS OF ANSI C80.3. FITTINGS SHALL BE

CORROSION-RESISTANT COMPRESSION TYPE.

2. SHEET METAL BOXES SHALL BE NEMA TYPE 1 GALVANIZED STEEL ENCLOSURE WITH SCREW COVER.

3. CONCEALED OR EXPOSED INTERIOR LOCATIONS: UTILIZE ELECTRICAL METALLIC TUBING ABOVE 10'-0" A.F.F., MINIMUM 3/4" .

4. UNDERGROUND OR IN CONCRETE: UTILIZE PVC, MINIMUM 1".

5. CONDUIT SIZE SHALL BE 3/4", MINIMUM. WHERE SIZE IS NOT SHOWN ON THE DRAWING, INSTALL 3/4" CONDUIT UNLESS RECOMMENDED

OTHERWISE BY THE EQUIPMENT MANUFACTURER.

6. LISTING AND LABELING: METAL CONDUITS, TUBING, AND FITTINGS SHALL BE LISTED AND LABELED AS DEFINED IN NFPA 70, BY A QUALIFIED

TESTING AGENCY, AND MARKED FOR INTENDED LOCATION AND APPLICATION.

7. GALVANIZED STEEL RIGID CONDUIT SHALL COMPLY WITH ANSI C80.1 AND UL 6, AND SHALL BE USED SURFACE MOUNTED CONDUIT FROM 0'-0" TO

10'-0" A.F.F. AND FOR ALL EXTERIOR AREAS.

8. LIQUID-TIGHT FLEXIBLE METAL CONDUIT SHALL EMPLOY PVC JACKET, COMPLY WITH UL 360, AND SHALL BE INSTALLED FOR FINAL CONNECTION TO

EQUIPMENT AND INSTRUMENTATION.

9. MAINTAIN MINIMUM 12 INCH CLEARANCE BETWEEN CONDUIT AND HEAT PRODUCING EQUIPMENT. SUPPORT CONDUIT AT DISTANCES NOT

EXCEEDING NEC RECOMMENDATIONS FOR SPECIFIC CONDUIT TYPES INSTALLED.

10. WHERE CONDUIT PENETRATES AN EXTERIOR WALL, THE PENETRATION SHALL BE SEALED WATERTIGHT. WHERE CONDUIT PENETRATES A FIRE RATED WALL, THE PENETRATION SHALL BE SEALED WITH FIRE RESISTANT SEALANT TO MATCH OR EXCEED THE RATING OF THE WALL.

11.CONDUIT ENTRY TO ENCLOSURES, PULL BOXES, OR EQUIPMENT SHALL BE VIA CONDUIT HUB - LISTED FOR INSTALLATION WITH RACEWAY

SYSTEM. DOUBLE LOCKNUTS ARE NOT SUITABLE FOR RACEWAY ENTRANCES.

16.3 WIRE AND CABLE

1. BUILDING WIRE

A. FEEDERS AND BRANCH CIRCUITS: COPPER, STRANDED CONDUCTOR, 600 VOLT INSULATION, TYPE THWN, COMPLYING WITH UL 83.

B. ALL WIRING SHALL BE INSTALLED IN RACEWAY.

2. WIRING CONNECTIONS AND TERMINATIONS

A. SPLICE ONLY IN ACCESSIBLE JUNCTION BOXES.

B. USE SOLDERLESS PRESSURE CONNECTORS WITH INSULATING COVERS FOR STRANDED TO STRANDED WIRE AND INSULATED SPRING WIRE CONNECTORS WITH PLASTIC CAPS FOR SOLID TO STRANDED AND SOLID TO SOLID COPPER WIRE SPLICES AND TAPS, NO. 8 AWG AND

SMALLER.

C. TAPE UNINSULATED CONDUCTORS AND CONNECTORS WITH ELECTRICAL TAPE TO 150 PERCENT OF THE INSULATION VALUE OF THE

CONDUCTOR.

3. WIRE/CABLE IDENTIFICATION

A. LABEL EACH WIRE AT ALL TERMINATION POINTS.

B. THE FOLLOWING COLOR CODING SHALL BE USED THROUGHOUT:

480/277V - 3 PHASE 120/208V - 3 PHASE:

PHASE A - BROWN PHASE A - BLACK

PHASE B - ORANGE PHASE B - RED

PHASE C - YELLOW PHASE C - BLUE

NEUTRAL - WHITE/GRAY NEUTRAL - WHITE

GROUND - GREEN GROUND - GREEN

120/240V - 1 PHASE:

PHASE A - BLACK

PHASE B - RED

NEUTRAL - WHITE

GROUND - GREEN

4. METAL CLAD CABLE

A. FACTORY ASSEMBLY OF ONE OR MORE CURRENT-CARRYING INSULATED CONDUCTORS IN AN OVERALL METALLIC SHEATH.

B. COMPLY WITH UL 1569

C. LISTED AND LABELED AS DEFINED IN NFPA 70.

D. CONDUCTOR INSULATION TYPE THHN/THWN-2; COMPLY WITH UL 83.

5. CABLE TESTING

A. ALL NEW CABLES, INCLUDING ALL TERMINATIONS SHALL BE TESTED AFTER INSTALLATION, AND PRIOR TO BEING ENERGIZED.

B. CABLE TEST SHALL CONSIST OF A CONDUCTOR CONTINUITY TEST FOR ALL CABLES 600 VOLTS AND BELOW.

C. TORQUE TEST ALL CONDUCTOR TERMINATIONS AND CONNECTIONS TO CABLE AND EQUIPMENT PER MANUFACTURER'S SPECIFICATIONS.

D. CORRECT MALFUNCTIONING PRODUCTS AT SITE, WHERE POSSIBLE, AND RETEST TO DEMONSTRATE COMPLIANCE; OTHERWISE, REMOVE

AND REPLACE WITH NEW AND RETEST.

6. APPLICATIONS

A. CONCEALED INTERIOR LOCATIONS: BUILDING WIRE IN RACEWAYS, OR MC CABLE IN ACCORDANCE WITH NEC REQUIREMENTS.

B. EXPOSED INTERIOR LOCATIONS: BUILDING WIRE IN RACEWAYS. EMT ABOVE 10'-0"A.F.F., RGS BELOW 10'-0" A.F.F.

C. EXTERIOR LOCATIONS: BUILDING WIRE IN RACEWAYS (RIGID GALVANIZED STEEL (RGS) CONDUIT).

16.4 PANELBOARDS

1. BASIS OF DESIGN: SQUARE D

2. BUS STRUCTURE AND MAIN LUGS AS SHOWN ON ONE-LINE DIAGRAM AND PANEL SCHEDULE.

3. CIRCUIT BREAKERS SHALL BE BOLT-ON, THERMAL-MAGNETIC, MOLDED CASE CIRCUIT BREAKERS. BREAKERS SHALL BE 1, 2, OR 3 POLES WITH AN INTEGRAL CROSSBAR TO ASSUME SIMULTANEOUS OPENING OF ALL POLES IN MULTIPLE POLE CIRCUIT BREAKERS. CIRCUIT BREAKERS SERVING

MECHANICAL LOADS SHALL BE UL LISTED TYPE HACR.

4. SHORT CIRCUIT RATING SHALL BE MINIMUM 10,000 RMS SYMMETRICAL AMPERES @ 120/208V, AND 14,000 RMS SYMMETRICAL AMPERES @ 277/480V.

5. BRANCH CIRCUIT PANELBOARDS SHALL BE LISTED BY UNDERWRITER'S LABORATORIES AND SHALL BEAR THE UL LABEL.

6. CIRCUIT BREAKERS PROVIDED FOR EXISTING PANELBOARDS SHALL BE COMPATIBLE WITH EXISTING PANELBOARD AND SHALL MEET THE SHORT

CIRCUIT RATING OF THE EXISTING PANELBOARD.

16.5 BOXES

1. PROVIDE ELECTRICAL BOXES AS REQUIRED FOR SPLICES, TAPS, EASE OF WIRE PULLING, EQUIPMENT CONNECTIONS, AND CODE COMPLIANCE, WHETHER OR NOT SPECIFICALLY SHOWN ON THE DRAWINGS. VERIFY AND COORDINATE THE LOCATION OF ALL BOXES AND OUTLETS WITH OTHER

TRADES.

16.6 LIGHTING

1. PROVIDE LIGHTING LUMINAIRES AND ASSOCIATED CONTROLS AS INDICATED ON THE CONTRACT DRAWINGS.

2. CONTRACTOR SHALL BE RESPONSIBLE FOR TRAINING OWNER'S PERSONNEL FOR OPERATION AND MAINTENANCE OF ALL LUMINAIRES AND

ASSOCIATED CONTROLS PROVIDED AS PART OF THIS PROJECT. CONTRACTOR SHALL COORDINATE TRAINING REQUIREMENTS WITH SUPPLIER IF

NECESSARY.

3. AFTER INSTALLING LUMINAIRES, SWITCHES, AND ACCESSORIES, AND AFTER ELECTRICAL CIRCUITRY HAS BEEN ENERGIZED, TEST UNITS TO

CONFIRM PROPER OPERATION.

4. TEST FOR EMERGENCY LIGHTING: INTERRUPT POWER SUPPLY TO DEMONSTRATE PROPER OPERATION. VERIFY TRANSFER FROM NORMAL POWER

TO EMERGENCY POWER.

16.6.2 WIRING DEVICES

1. RECEPTACLES SHALL BE SPECIFICATION GRADE. THE FACE AND BACKBODY OF THE RECEPTACLE SHALL BE OF HIGH-IMPACT THERMOPLASTIC.

THE CONTACTS SHALL BE TRIPLE WIPE, T-SLOT, ONE-PIECE COPPER ALLOY DESIGN. THE RECEPTACLE SHALL INCLUDE A GREEN GROUND SCREW ATTACHED TO THE INTO THE BODY OF THE RECEPTACLE. RECEPTACLES SHALL BE RATED 20-AMPERE, 125-V AC, NEMA CONFIGURATION 5-20R, SIDE WIRED WITH AN BLACK FINISH.

2. GROUND FAULT CIRCUIT INTERRUPTER RECEPTACLES (GFCI) SHALL HAVE A NYLON FACE AND A THERMOPLASTIC BACKBODY. GFCI RECEPTACLES SHALL BE UL CLASS A WITH A 5-MILLIAMPERE, GROUND-FAULT TRIP LEVEL. GFCI RECEPTACLES SHALL BE RATED 20-AMPERE, 125-V AC, NEMA CONFIGURATION 5-20R, SIDE WIRED WITH AN BLACK FINISH.

3. WALL SWITCHES SHALL BE HARD USAGE, SPECIFICATION GRADE, QUIET TYPE. THE BODY OF THE SWITCH SHALL BE CONSTRUCTED OF AN ARC-RESISTANT THERMOSET MATERIAL. THE TOGGLE SWITCH HANDLE SHALL BE CONSTRUCTED OF A THERMOPLASTIC MATERIAL SUCH AS "LEXAN". THE CONTACT ARMS SHALL BE OF A ONE-PIECE COPPER ALLOY MATERIAL. THE SWITCH SHALL ALSO INCLUDE A GREEN GROUND SCREW ATTACHED TO THE MOUNTING STRAP. SWITCHES SHALL BE RATED 20-AMPERE, 120-277-V AC, SIDE WIRED WITH AN BLACK FINISH.

4. GENERAL USE WALL PLATES SHALL BE TYPE 302 SATIN STAINLESS STEEL. THE PLATE SHALL BE OF A MODERN DESIGN WITH ROUNDED EDGES

AND CORNERS.

5. REPLACE RECEPTACLES AT EXISTING LOCATIONS.

16.7 SECONDARY GROUNDING

1. ELECTRICAL GROUNDING SYSTEM SHALL FULLY COMPLY WITH THE REQUIREMENTS OF THE NATIONAL ELECTRICAL CODE - ARTICLE 250.

2. CONNECT ALL NONCURRENT CARRYING METAL PARTS SUCH AS METAL CONDUITS, RACEWAYS, OUTLET BOXES, CABINETS, SUPPORTS, AND

SIMILAR PARTS OF ALL ELECTRICAL EQUIPMENT AND APPARATUS TO THE GROUNDING SYSTEM.

3. EQUIPMENT GROUNDING CONDUCTORS: COMPLY WITH NEC ARTICLE 250 FOR TYPES, SIZES, AND QUANTITIES OF EQUIPMENT GROUNDING CONDUCTORS, EXCEPT WHERE SPECIFIC TYPES, LARGER SIZES, OR MORE CONDUCTORS THAN REQUIRED BY NEC ARE INDICATED.

4. PROVIDE A SEPARATE, GREEN INSULATED EQUIPMENT GROUNDING CONDUCTOR FOR ALL FEEDER AND BRANCH CIRCUITS. TERMINATE EACH ON

A GROUNDING LUG, BUS, OR BUSHING.

16.8 ELECTRICAL IDENTIFICATION

1. ALL WIRE AND CABLE SHALL BE MARKED. POWER CABLES SHALL BE COLOR CODED AS NOTED IN PARAGRAPH 16.3.3.B. CONTROL AND

INSTRUMENTATION WIRE SHALL BE NUMBERED AT BOTH ENDS.

2. ENGRAVED THREE-LAYER LAMINATED PLASTIC, BLACK LETTERS ON A WHITE BACKGROUND.

3. PROVIDE NAMEPLATES TO IDENTIFY ALL ELECTRICAL DISTRIBUTION AND CONTROL EQUIPMENT, AND LOADS SERVED. PANELBOARDS SHALL HAVE PANEL NAME, AMPERAGE, AND VOLTAGE PROVIDED ON FRONT COVER OF PANEL. PANELS SHALL BE PROVIDED WITH TYPED CIRCUIT

DIRECTORIES IDENTIFYING ALL LOADS SERVED.

4. ALL NEW LIGHTING CONTROL EQUIPMENT SHALL BE PROPERLY IDENTIFIED.

5. PROVIDE SELF-ADHESIVE WARNING LABELS, FACTORY PRINTED, MULTICOLOR, CONFIGURED FOR DISPLAY ON FRONT COVER, DOOR OR OTHER ACCESS TO EQUIPMENT. WARNING LABELS AND SIGNS SHALL INCLUDE THE FOLLOWING LEGENDS:

A. EACH NEW PANELBOARD: "WARNING: POTENTIAL ARC-FLASH HAZARDS EXIST WHILE WORKING ON THIS ENERGIZED EQUIPMENT".

B. WORKSPACE CLEARANCE: "WARNING: OSHA REGULATION - AREA IN FRONT OF ELECTRICAL EQUIPMENT MUST BE KEPT CLEAR FOR 42

INCHES".

16.9 GENERATOR AND AUTOMATIC TRANSFER SWITCH

1. BASIS OF DESIGN; GENERAC: GENERATOR:XG04845 48kW, 200AMP, 120/240VAC, SINGLE PHASE, 3 WIRE, TYPE 3R QUIET ENCLOSURE (58dB

@OPERATING SPEED, NO LOAD @23FT); OR APPROVED EQUAL.

2. PACKAGED PROPANE ENGINE GENERATOR SYSTEM SHALL INCLUDE ENGINE GENERATOR, ATS, COOLING SYSTEM, COMBUSTION AIR INTAKE AND ENGINE EXHAUST SYSTEMS, STARTING SYSTEM, AND THE FOLLOWING ADDITIONAL FEATURES: BATTERY CHARGER, GENERATOR SET MAIN CIRCUIT BREAKER, ENGINE BLOCK HEATER, REMOTE E-STOP, BASEFRAME BLOCKOFF KIT, ENGINE FLUID CONTAINMENT KIT, AND ENGINE

EXHAUST PIPING AND INSULATION.

3. POWERZONE 410 CONTROLLER, NFPA 110 SYSTEM CAPABLE, CORROSION RESISTANT ALUMINUM ENCLOSURE, ELECTRO-GALVANIZED BASEFRAME W/ STAINLESS STEEL EXHAUST SYSTEM. EPA EMISSION CERTIFIED, UL 2200 LISTED, HIGH MOTOR STARTING AND SURGE CAPACITY, RATINGS: 48 KW, 120/240 VAC, 200AMP, SINGLE PHASE, 60 Hz. 5 YEAR/2,000 HOUR LIMITED WARRANTY.

4. ENGINE: THE ENGINE SHALL BE 4 CYCLE, RADIATOR AND FAN COOLED. GOVERNOR:ELECTRONIC, FREQUENCY REGULATION: ISOCHRONOUS.

5. AC GENERATOR: SYNCHRONOUS, ROTOR INSULATION CLASS 'F', STATOR INSULATION CLASS 'H', SEALED BEARING, FLEXIBLE DISC COUPLING, DIRECT EXCITATION SYSTEM, TOTAL HARMONIC DISTORTION <5%. DIGITAL VOLTAGE REGULATION, SENSING OF ALL PHASES, REGULATION 1%

ABOVE OR BELOW RATED VOLTAGE.

6. COOLING SYSTEM: WATER PUMP BELT DRIVEN, SKID MOUNTED RADIATORS RATED FOR FULL LOAD OPERATION IN 122°F AMBIENT AS MEASURED AT THE GENERATOR AIR INLET. RADIATOR W/ ELECTRIC FAN SHALL BE BY 50/50 ETHYLENE GLYCOL/WATER MIXTURE BY THE EQUIPMENT

SUPPLIER.

7. FUEL SUPPLY SYSTEM: PROPANE.

8. STARTING AND CONTROL BATTERIES: 12 VOLT. STARTING BATTERY BANK FLOODED LEAD ACID, GROUP 27, 600 CCA MIN.

BATTERY CHARGER: 5 AMP.

9. GENERATOR MAIN CIRCUIT BREAKER: SET MOUNTED & WIRED; UL LISTED, MOLDED CASE 200 AMP, 42,000AIC.

10. SURGE CAPACITY 15% VOLTAGE DIP 220A, 30% VOLTAGE DIP 340A.

11.COLOR: METRO GRAY

AUTOMATIC TRANSFER SWITCH

12. BASIS OF DESIGN: GENERAC TX301, 200AMP, 120/240VAC, SINGLE PHASE, TYPE 1, 3 POLE, SERVICE ENTRANCE RATED W/ 200A, 42,000 AIC MOLDED

CASE CIRCUIT BREAKER ; OR APPROVED EQUAL.

13. TRANSFER SWITCH COMPLETE WITH ACCESSORIES SHALL BE UL LISTED. SOLID STATE CONTROLS: REPETITIVE ACCURACY OF ALL SETTINGS

PLUS OR BETTER OVER AN OPERATING TEMPERATURE RANGE OF MINUS -20°C TO 70°C.

14. TRANSFER SWITCH FEATURES:

A. SMALL FOOTPRINT, RESULTS IN EASY MOUNTING AND

B. INSTALLATION FOR REDUCED TIME AND COSTS

C. DOUBLE-THROW, STORED ENERGY TRANSFER MECHANISM

D. CAN BE ELECTRICALLY ISOLATED WHILE ENERGIZED

E. GRAPHICAL LCD-BASED DISPLAY FOR PROGRAMMING, SYSTEM DIAGNOSTICS AND HELP MENU DISPLAY MIMIC

F. DIAGRAM WITH SOURCE AVAILABLE AND CONNECTED LED INDICATOR

G. METHOD OF TRANSFER: OPEN WITH INPHASE TRANSITION

H. MECHANICALLY INTERLOCKED TO PREVENT CONNECTION OF BOTH SOURCES

I. MODBUS® RTU COMMUNICATIONS

J. TXC 100 CONTROLLER

K. OPERATING TEMPERATURE -4 ° TO 158 °F

L. REMOVABLE TOP AND BOTTOM PLATES FOR EASE OF ENTRY

M. HIGH WITHSTAND AND CLOSING RATINGS

N. AUXILIARY OUTPUT INCLUDES: TWO WIRE START, SIGNAL BEFORE TRANSFER, FAULT, AND A PROGRAMMABLE RELAY OUTPUT

O. AUXILIARY INPUT INCLUDES: PERMISSIVE INPUTS (24 VDC)

P. GENERAL ALARM INDICATION

Q. 2 YEAR STANDARD WARRANTY

R. IBC 2018, 2015, 2012, 2009

16.10 TESTING

1. AFTER ELECTRICAL INSTALLATION IS COMPLETE, MAKE TESTS TO DEMONSTRATE THAT ENTIRE SYSTEM IS IN PROPER WORKING ORDER AND IN ACCORDANCE WITH DRAWINGS AND SPECIFICATIONS. MAKE NO TESTS LESS THAN OUTLINED HEREAFTER, UNLESS REQUESTED IN WRITING AND APPROVED BY THE OWNER. TESTS ARE IN ADDITION TO AND NOR A SUBSTITUTION FOR TESTS OF INDIVIDUAL ITEMS.

2. TESTING SHALL BE PER NETA ATS.

3. PAY ALL COSTS FOR TESTS, INCLUDING COSTS TO RETEST OCCASIONED BY DEFECTS AND FAILURES OF EQUIPMENT TO MEET SPECIFICATIONS.

A. REPLACE WIRING AND EQUIPMENT FOUND DEFECTIVE, OR FAILING TO MEET SPECIFIED REQUIREMENTS, WITHOUT CHARGE, UNLESS

WRITTEN ACCEPTANCE FOR REPAIR IS GIVEN BY OWNER.

B. FURNISH THREE COPIES OF ALL TEST RESULTS TO OWNER.

4. CALIBRATION: FURNISH SUITABLE ELECTRICAL INSTRUMENTS, INCLUDING VOLTMETERS, AMMETERS, WATTMETERS, AND ALL OTHER EQUIPMENT NECESSARY TO PERFORM TESTS SPECIFIED. MAKE NECESSARY OPENINGS IN CIRCUITS FOR TESTING INSTRUMENTS AND PLACE AND CONNECT ALL INSTRUMENTS, EQUIPMENT, AND DEVICES, NECESSARY FOR THE TESTS. UPON COMPLETION OF TESTS, REMOVE INSTRUCTIONS AND INSTRUMENT CONNECTIONS AND RESTORE ALL CIRCUITS TO PERMANENT CONDITION. CONDUCT TESTS IN PRESENCE OF OWNER.

5. TESTS:

A. INSULATION RESISTANCE TESTS OF CIRCUITS, 600 VOLTS AND BELOW:

B. DO NOT SUBJECT CONDUCTORS RATED 600 VOLTS AND BELOW TO HIGH POTENTIAL DIELECTRIC TESTS. TEST COMPLETE FEEDER AND

BRANCH CIRCUIT OF 600 VOLTS OR BELOW WITH EVERYTHING BUT POWER SUPPLY AND POWER-CONSUMING EQUIPMENT, CONNECTED

THERETO.

C. DETERMINE INSULATION RESISTANCE VALUES WITH ALL SWITCHES AND OVERCURRENT DEVICES IN PLACE.

D. USE MEGOHMETER HAVING OUTPUT OF AT LEAST 500 VOLTS TO DETERMINED INSULATION RESISTANCE VALUE FOR 600 VOLT RATED

CONDUCTORS.

E. ALL CABLES FAILING INSULATION TEST SHALL BE REMOVED, REPLACED, AND RE-TESTED.

F. WHERE TESTS OF ANY OF THE ABOVE-REFERENCED EQUIPMENT ARE INCLUDED IN OTHER SECTIONS OF SPECIFICATIONS, COORDINATE

TESTING, AS DIRECTED BY OWNER, TO AVOID DUPLICATION AND CONFLICT BETWEEN TESTS.

G. PERFORM ABOVE TESTS IN ADDITION TO, AND NOT IN SUBSTITUTION FOR REQUIRED MANUFACTURER'S FACTORY TESTS.

5. OPERATING TESTS:

A. OPERATE CIRCUIT BREAKERS AND CONTROL DEVICES TO SHOW CORRECT AND SATISFACTORY OPERATIONS.

B. WHERE TESTS OF ANY OF THE ABOVE-REFERENCED EQUIPMENT ARE INCLUDED IN OTHER SECTIONS OF SPECIFICATIONS, COORDINATE

TESTING, AS DIRECTED BY OWNER, TO AVOID DUPLICATION AND CONFLICT BETWEEN TESTS.

AutoCAD SHX Text THIS DOCUMENT IS THE PROPERTY OF HANOVER ENGINEERING ASSOCIATES, INC. ANY USE OF A COPY OF THIS DOCUMENT THAT DOES NOT CONTAIN AN ORIGINAL SEAL AND SIGNATURE IS STRICTLY PROHIBITED. THIS DOCUMENT IS NOT PUBLISHED AND ALL RIGHTS ARE RESERVED BY HANOVER ENGINEERING ASSOCIATES, INC. THIS PLAN HAS BEEN SEALED WITH EITHER A RED INK SEAL OR A CRIMP SEAL. IF NEITHER APPEARS ON THIS PLAN, POSSIBLE REPRODUCTIONS OR ALTERATIONS MAY HAVE BEEN MADE WITHOUT THE APPROVAL OR KNOWLEDGE OF THE SIGNATORY.

AutoCAD SHX Text

DATE

AutoCAD SHX Text

NO.

AutoCAD SHX Text

REVISIONS

AutoCAD SHX Text

PLAN TITLE:

AutoCAD SHX Text

PROJECT TITLE:

AutoCAD SHX Text

SHEET NO.

AutoCAD SHX Text

PROJECT NO.

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

CHECKED BY:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

DATE:

AutoCAD SHX Text 01/14/25

AutoCAD SHX Text L22-24

AutoCAD SHX Text

TOWNSHIP MAINTENANCE FACILITY

AutoCAD SHX Text

LONGSWAMP TOWNSHIP BERKS COUNTY PENNSYLVANIA

AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text 02-11-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR PERMITS

AutoCAD SHX Text

102 LONGSDALE DRIVE BUILDING ADDITION

AutoCAD SHX Text

SEAL:

AutoCAD SHX Text 09-01-26

AutoCAD SHX Text

AutoCAD SHX Text

ISSUED FOR BIDDING

AutoCAD SHX Text

CJD

AutoCAD SHX Text

CRS

ELECTRICAL-SPECIFICATIONS