Fontana Unified School District

PLUMBING PIPING

22 42 00

Revised: 01/07/22 Page 1 of 65 Plumbing Piping Section 22 42 00

PART 1 - GENERAL

1.01 SUMMARY

A. Provisions of Division 01 apply to this section

B. Section Includes: Furnish labor, materials, tools, and equipment to install plumbing systems as indicated.

C. Related Sections:

1. Section 31 20 00: Excavation, Backfilling and Compacting for Utilities.

2. Section 10 44 13: Fire Extinguishers and Cabinets

3. Section 23 05 00: Basic Mechanical Requirements.

4. Section 23 05 13: Basic Mechanical Materials and Methods.

5. Section 23 05 48: Mechanical Sound, Vibration and Seismic Control.

6. Section 23 05 53: Mechanical Identification.

7. Section 23 07 00: Mechanical Insulation.

8. Division 26: Electrical.

1.02 SUBMITTALS

A. Provide in accordance with Division 23 and Section 23 05 00: Basic

Mechanical Requirements.

1.03 QUALITY ASSURANCE

A. Unless otherwise noted, provisions including amendments thereto, of the State Plumbing Code Part 5, Title 24, CCR; of the Uniform Plumbing Code, latest edition; and of the latest Plumbing Ordinances of the City of Fontana and/or County of San Bernardino are hereby made part of this section.

B. Conform to provisions f Section 23 05 00: Basic Mechanical Requirements.

C. Manufacturer of plumbing products shall obtain ANSI/NSF Standard 61, ef 9 certification to demonstrate compliance with the federal requirements for lead contribution to drinking water (Safe Drinking Water Act SDWA).

1.04 PRODUCT HANDLING

A. Conform to provisions of Section 23 05 13: Basic Mechanical Materials and Methods.

22 42 00

Revised: 01/07/22 Page 2 of 65 Plumbing Piping Section 22 42 00

PART 2 - PRODUCTS

2.01 PIPING SYSTEMS

A. Materials: Refer to Section 23 05 13: Basic Mechanical Materials and Methods.

B. Insulation for Piping: Refer to Section 23 07 00: Heating and Air Conditioning Piping Systems.

2.02 FIXTURES AND DRAINS

A. General: Fixtures specified shall be furnished complete with trim and fittings. Cast iron plumbing fixtures shall be acid resistant enamel, and identified by casting letters "AR" or words "acid-resistant" into metal.

Fixtures shall be white unless otherwise specified. Cast iron fixtures shall be white enamel inside and on back, rim and apron, with exposed unfinished surfaces painted white. Fixtures of same general classifications shall be of same make.

B. Finished Brass:

1. Unless otherwise specified, finished brass of a similar type shall be of same manufacturer throughout buildings.

2. Finished and exposed brass equipment, except floor, shower, and urinal drains shall be chromium-plated and polished.

Floor, shower, and urinal drains, unless otherwise specified, shall be nickel-bronze metal.

C. Traps, Trap Arms and Tailpieces:

1. Fixture traps shall be cast brass, chromium-plated, and polished. (No tubular traps). Exceptions as follows:

a. Traps that are an integral part of fixture.

b. Traps concealed in floors, walls, and furring.

c. Traps standard for service sinks and Industrial Shop equipment.

2. Concealed traps and tailpieces may be rough brass, except as otherwise specified. Laboratory traps and tailpieces shall be flame retardant polypropylene. Furnish chromium-plated and polished cast brass wall flanges with setscrews and chromium-plated and polished brass casing on discharge side of each trap.

3. Tailpieces shall be not lighter than 17 gauge, brass, chromium-plated, and polished. Furnish and install chromium brass plated wall flanges with set screws and chromium-plated 20 gauge brass casing on discharge side of each chrome-plated trap.

22 42 00

Revised: 01/07/22 Page 3 of 65 Plumbing Piping Section 22 42 00

D. Faucet and Shower Valve Handles: Faucet and shower valve handles shall be solid brass, chromium-plated and polished, and fastened to their stems by Allen type hollow head stainless steel set screws through the side of the handle extending into the stem. Handles with sharp edges or projections shall not be furnished.

E. Fixture Supplies:

1. Supplies for garbage disposal units and water heaters shall be unplated rigid copper water tube with threaded adaptors for connections to valves and other threaded connections. All other supplies shall be chromium-plated brass with hospital threads or shall be furnished with fittings and valves, which completely cover threads.

2. Exposed supplies for showers shall be chromium-plated brass pipe up to header with hospital threads or shall be furnished with fittings and valves, which completely cover threads.

3. Supplies to water closet tanks, lavatories, and drinking fountains shall be furnished with chromium-plated and polished screwed type angle compression stops with square shank stems and lock shields extending beyond stem. Instead of solid supply piping, polished chrome-plated risers of 3/8 inch outside diameter with ferrule stop end and metal nosepiece may be furnished. The installation of braided stainless or easy hookers supplies. Exception: Supplies that rise vertically from floor shall be furnished with straight type instead of angle type stops.

4. Each supply or pipe that penetrates a finished surface and plumbing pipes passing through a countertop or part of a cabinet shall be furnished with a chromium-plated brass flange except flanges furnished by manufacturer of flush valves as an assembly.

5. Water supplies of plumbing fixtures shall be protected against back-siphonage in event of a vacuum in piping system.

6. Discharge outlets of supply faucets for lavatories and sinks shall clear top of overflow rim by at least one inch.

7. Toilet and urinal flush valves shall be furnished with recognized atmospheric vacuum breakers, installed per manufacture’s instruction a minimum of 6 inches above fixture.

2.03 ACCESS PLATES (TO CLEANOUTS, VALVES, WATER HAMMER ARRESTORS AND HOSE

FAUCETS)

A. Schedule Numbers:

1. AP-1: Square, unless otherwise noted, steel, prime coated;

frame, 18-gauge minimum. Door shall be 16-gauge minimum with concealed hinge or removable door, vandal-proof lock

22 42 00

Revised: 01/07/22 Page 4 of 65 Plumbing Piping Section 22 42 00 operated by Allen wrench. (Specify for painted or stucco walls.)

SMITH Fig. 4760 AK

ZURN Z-1462-VP

ELMDOR DW-AKL

MILKOR DW AK1

2. AP-2: Round type, stainless steel, vandal-proof, 5/16 inch No.

18 or 1/4 inch No. 20 flat-head machine screw into cleanout plug. Plate shall be prime coated minimum 18 gauge steel or polished chrome-plated brass, 18-8 No. 302 stainless steel, or polished nickel bronze. (Specify for painted walls, screwed into cleanout plug.)

SMITH 4710U

ZURN Z-1469-VP

JOSAM 58600

WADE 8480R

3. AP-3: Square, polished face chrome-plated bronze, aluminum alloy or brass chrome-plated brass frame with 14 gauge polished 18-8 No. 302 stainless steel or brass chrome-plated secured cover with vandal-proof screws. (Specify for tile walls.)

SMITH 4735U

ZURN Z-1460-VP

WADE 8480-S

4. AP-4: Square, floor type, cast nickel-bronze aluminum alloy or brass, with carborundum or scoriated, secured top. (Specify for floor access to solid interceptor in Science Room, Ceramic Room, and Agriculture Room.)

SMITH 4910U

ZURN Z-1461-VP

JOSAM 56030

2.04 BACKFLOW PREVENTION ASSEMBLIES

A. Schedule Numbers:

1. BPV-1: Pressure vacuum breakers 1/2 inch to 2 inches. (Specify for irrigation lines to protect the potable water systems)

22 42 00

Revised: 01/07/22 Page 5 of 65 Plumbing Piping Section 22 42 00

WILKINS 720A

WATTS 800 M4QT

2. BPV-2: Non-pressure type, atmospheric vacuum breaker.

CHAMPION 262

WATTS 288A

WILKINS 35

3. BPV-3: Reduced pressure or pressure differential type. (Specify where potential health hazard exists and at main meter.) Sizes 2-1/2 inches to 6 inches.

WILKINS 975 or 375 (for uninterrupted service)

WATTS 909 NES 009 NRS

FEBCO 860, 870, 880

4. BPV-4: Double check valve assembly for water protection.

(Specify where no potential health hazards exist.) Sizes 2-1/2 inches to 6 inches.

FEBCO 850

WILKINS 950 or 350

WATTS 709

5. BPV-5: Double check valve assembly. (Specify with non-toxic systems or where no potential health hazard exists.) Sizes 3/4 inch to 2 inches.

WILKINS 950 XL or equal

WATTS 007

6. BPV-6: Pressure vacuum breakers with 3/4 inch hose bib.

Installation per manufacturer’s recommendation.

WILKINS 720A

WATTS 800M3QT

2.05 BACKWATER SEWER VALVE ASSEMBLY

A. Schedule Numbers:

1. BSV-1: Cast iron with access cover, with line size gate valve upstream and downstream.

SMITH 7022-S

ZURN Z-1090

22 42 00

Revised: 01/07/22 Page 6 of 65 Plumbing Piping Section 22 42 00

2.06 CLEANOUT ASSEMBLIES

A. Cleanout plug shall be line size.

B. Schedule Numbers:

1. CO-1: Iron body cleanout tee full line size up to 4 inches and round access plate, plugs shall be brass, countersunk with tapped boss for 5/16 inch No. 18 or 1/4 inch No. 20 screws.

(Specify for finished walls at base of waste stack, above urinal and service sink.)

SMITH 4532-U

ZURN Z-1446-BP

2. CO-2: Iron body with approved UPC plug, top and adjustable sleeve, cut-off ferrule, polished scoriated brass nickel bronze secured cover. (Specify for finished floors inside buildings, in covered areas, and in concrete paving.)

a. Square:

SMITH 4053L-U-RB

ZURN ZN-1400-T

b. Round:

SMITH 4033-L

ZURN ZN-1400

3. CO-3: Secured cover, extra heavy-duty, adjustable sleeve, cut-off ferule, UPC. Brass approved type plug, scoriated tractor type cover. (Specify for areas outside building on concrete paving.)

SMITH 4233

ZURN ZN-1400-HD

4. CO-4: Tapped soil tee with brass plug, full line size. (Specify for above grade, outside building at base of exposed downspout.)

SMITH 4512

ZURNZ 1445-BP

5. CO-5: Raised threaded head brass plug. (Specify for YB-3.)

ZURN Z-1470-A

22 42 00

Revised: 01/07/22 Page 7 of 65 Plumbing Piping

2.07 CIRCULATING PUMPS, HOT WATER HEATING SYSTEM

1. CPH-1: Centrifugal, single stage, close coupled with adjustable cast iron base, bronze enclosed impeller, lead-free mechanical shaft seal suitable for water temperature range from 20 degrees to 300 degrees F. Screwed or flanged connections. GPM and TDH capacities as indicated.

a. BELL & GOSSETT

b. WEIMAN

c. PACIFIC

2. CPH-2: In-line mounted. Close coupled, centrifugal type with an all bronze water chamber, bronze sleeve bearings, bronze impellers, water tight shaft seal suitable for water temperature range from 20-300 degrees F. Forged steel shaft. Provided with bracket support to damper vibrations. GPM and TDH capacities as indicated.

a. BELL & GOSSETT

b. GRUNDFOS

c. TACO

2.08 DRINKING FOUNTAINS

A. Schedule Numbers:

1. DF-1: Multiple, wall-mounted, cast aluminum with white powder coated finish, having three chrome-plated forged brass integral basin shank vandal- resistant bubbler heads, with flow/pressure regulating valves and chrome- plated solid brass adjustable push button activation, chrome-plated cast brass grid waste strainer with integral keyed locking lugs for vandal resistance. An easily serviceable 60 micron water supply strainer at inlet, mounting brackets, and vandal-resistant bottom plate shall be furnished. Complete drinking fountain with trim and brass compression fittings must have been tested and certified lead free to ANSI/NSF 61, Section 9.

(Specify for outdoor use located on High School Sanitary unit at Athletic Field.)

HAWS 1441

22 42 00

Revised: 01/07/22 Page 8 of 65 Plumbing Piping Section 22 42 00

2. DF-2: Multiple, disabled accessible wall-mounted cast iron with white porcelain enamel finish, providing 2 chrome-plated forged brass integral basin shank vandal-resistant bubbler heads, with flow/pressure regulating valves and chrome-plated solid brass adjustable push button activation. Chrome-plated cast brass grid waste strainer with integral keyed locking lugs for vandal resistance. An easily serviceable 60-micron water supply strainer at inlet, mounting brackets, and vandal-resistant bottom plate shall be furnished. Complete drinking fountain with trim and brass compression fittings must have been certified lead free to ANSI/NSF 61, Section 9.

HAWS 1431

3. DF-3: Single, disabled accessible wall-mounted recessed 18 gauge Type 304 stainless steel drinking fountain with satin finish, furnished with a single chrome-plated forged brass integral basin shank vandal-resistant bubbler head, with flow/pressure regulating valve and chrome-plated solid brass adjustable push button activation, vandal-resistant chrome-plated solid brass flat waste strainer, with an easily serviceable 60 micron water supply strainer at inlet. Complete drinking fountain with trim and brass compression fittings must have been tested and certified lead free to ANSI/NSF 61, Section 9.

(Specify for indoor use, fully disabled accessible with a 32 inches wide x 18 inches deep alcove wall cut-out below the fountain mounted at a 36-inch bubbler height. Specifically for indoor use in Middle School Library, Physical Education Building, and Administration Office.)

HAWS 2405

4. DF-3A: Single, wall-mounted recessed 18 gauge Type 304 stainless steel drinking fountain with satin finish, furnished with a single chrome-plated forged brass integral basin shank vandal-resistant bubbler head, with flow/pressure regulating valve and chrome-plated solid brass adjustable push button activation, vandal-resistant chrome-plated solid brass flat waste strainer, with an easily serviceable 60 micron water supply strainer at inlet. Complete drinking fountain with trim and brass compression fittings must have been tested and certified lead free to ANSI/NSF 61, Section 9. (Specify for indoor locations where wheelchair accessibility is not required.)

HAWS 2400

22 42 00

Revised: 01/07/22 Page 9 of 65 Plumbing Piping Section 22 42 00

5. DF-4: Single, wall-mounted, white vitreous china drinking fountain furnished with a single chrome-plated, forged brass integral basin shank, vandal- resistant bubbler head with flow/pressure regulating valve and chrome-plated solid brass, adjustable push button activation, vandal-resistant chrome-plated solid brass flat waste strainer, bottom plate, and easily serviceable 60-micron water supply strainer at inlet. Complete drinking fountain with trim and brass compression fittings must have been tested and certified lead free to ANSI/NSF 61, Section 9. (Specify for indoor use in Middle School Multi- Purpose Building, Agricultural Classroom and High School Administration Unit.)

HAWS 1201

6. DF-5: Single, disabled accessible recessed wall-mounted drinking fountain with matching cuspidor combination, dual 18 gauge Type 304 stainless steel receptors with satin finish, furnished with a single chrome-plated forged brass integral shank vandal-resistant bubbler head in the fountain, with flow/pressure regulating valve and chrome-plated solid brass adjustable push button activation, with an easily serviceable 60 micron water supply strainer at the inlet, a chrome-plated cast brass water spreader in the cuspidor, and chrome-plated solid brass flat waste strainers in both. The complete drinking fountain with trim and brass compression fittings must have been tested and certified lead free to ANSI/NSF 61, Section 9.

(Specify for indoor use in Physical Education and Gymnasium locations, fully disabled accessible with alcove wall cut-out below the fountain/cuspidor mounted at 36-inch bubbler height, use DF-3 in Girls' Gymnasium. Specify for use in High School Gymnasium Building and Middle School Physical Education Building, delete use of cuspidor in Girls' Gym.)

HAWS 2406

7. DF-5A: Single, recessed wall-mounted drinking fountain furnished with matching cuspidor combination, dual 18 gauge Type 304 stainless steel receptors with satin finish, furnished with a single chrome-plated forged brass integral shank vandal-resistant bubbler head in the fountain, with flow/pressure regulating valve and chrome-plated solid brass adjustable push button activation, with an easily serviceable 60-micron water supply strainer at the inlet, a chrome-plated cast brass water spreader in the cuspidor, and chrome-plated solid brass flat waste strainers in both. The complete drinking fountain with trim and brass compression fittings must have been tested and certified lead free to ANSI/NSF 61, Section 9.

(Specify for indoor use in Physical Education and Gymnasium

22 42 00

Revised: 01/07/22 Page 10 of 65 Plumbing Piping Section 22 42 00 locations where wheelchair accessibility is not required.

Specify DF-3A in Girls' Gymnasium.)

HAWS 2403

ELKAY EDFP-214-C

Or equal.

8. DF-6: Multiple, disabled accessible wall-mounted cast aluminum fountain with white powder coated finish, furnished with two chrome-plated forged brass integral shank vandal-resistant bubbler heads, with flow/pressure regulating valves and chrome-plated solid brass adjustable push button activation, chrome-plated cast brass grid waste strainer with integral keyed locking lugs for vandal resistance. An easily serviceable 60 micron water supply strainer at inlet, integral mounting brackets, and vandal-resistant bottom plate shall be included. Complete drinking fountain with trim and brass compression fittings, tested and certified lead free to ANSI/NSF 61, Section 9. Install with 1/4 inch thick steel mounting plate inside the wall. (Specify for outdoor handicap use at Owner’s Multi-Purpose Buildings, Elementary and High School Sanitary Unit, Middle School Physical Education Bldg.) Piping furnished with unit shall be Type L copper.

a. Fountain:

HAWS 1441

b. Mounting plate:

HAWS 6710

9. DF-7: Dual height, 2 disabled accessible wall-mounted, 14 gauge Type 304 stainless steel dual height drinking fountains of one-piece construction, with 1/4 inch thick stainless steel backs, furnished with 2 chrome-plated forged brass integral basin shank, vandal-resistant bubbler heads, with flow/pressure regulating valves and chrome-plated solid brass adjustable push button activation, with chrome-plated cast brass waste strainers, bottom plates and easily serviceable 60-micron water supply strainers at inlet. Install with a 3/16 inch thick steel mounting plate inside the wall. (Specify for fully disabled accessible for indoor severe vandalism locations, lowest fountain, mounted at 36 inches to 34 inches bubbler height for ages 12 and over, lowest fountain mounted at 32 inches to 31 inches bubbler height for Elementary School age, lowest fountain mounted at 30 inches to 29 inches bubbler height for Kindergarten age children.)

22 42 00

Revised: 01/07/22 Page 11 of 65 Plumbing Piping

HAWS 1119.14, with bracket 6700.4

10. DF-8: Disabled accessible single bubbler white porcelain enamel cast iron wall-mounted drinking fountain; furnished with vandal-resistant lead free PCP forged brass bubbler head, PCP cast brass waste strainers, stream adjustable PCP machined brass push button operation and pressure regulating valves. Bottom cover plates, 1-1/2 inch brass trap, 60 micron water inlet strainer. ADA compliant and certified lead free to ANSI/NSF Standard 61, Section 9.

a. Fountain: HAWS 1311

b. Mounting plate: HAWS 6700

c. Installation: Furnish a 3/16 inch thick steel mounting plate No. 6700, which can also be installed with model No. 6800 concealed carrier steel struts for additional support where wall-mounted fountain may be subjected to excessive leverage.

11. DF-8A: Disabled accessible dual height white porcelain enamel cast iron wall- mounted drinking fountains; furnished with vandal-resistant lead free PCP forged brass bubbler heads, PCP cast brass waste strainers, stream adjustable PCP machined brass push button operation and pressure regulating valves. Bottom cover plates, 1-1/2 inch brass rap, 60 micron water inlet strainer. ADA compliant and certified lead free to ANSI/NSF Standard 61, Section 9.

a. Fountain: HAWS 1501

b. Mounting plate: HAWS 6715

c. Installation: Furnish a 3/16 inch thick steel mounting plate number 6715, which can also be installed with model No. 6800 concealed carrier steel struts for additional support where wall-mounted fountain may be subjected to excessive leverage.

2.09 DRUM TRAP

A. Schedule Numbers:

1. DT-1: Extra heavy cast iron, bolted top.

SMITH 8714

ZURN ZA1180

22 42 00

Revised: 01/07/22 Page 12 of 65 Plumbing Piping Section 22 42 00

2. DT-2: Aluminum solid interceptor, furnish for on-floor installation.

SMITH 8710-AA

ZURN Z-1180

2.10 DIELECTRIC UNIONS

1. DU-1: Brass union with 6-inch brass nipple.

2. DU-2: Union-flanged.

a. WATTS 3100-IPXS, 3110-SXS, 3200-IPXIP

2.11 EMERGENCY EYE WASH/EMERGENCY SHOWER

A. Schedule Numbers:

1. EEW-1: Recessed ADA Barrier Free combination emergency shower and fold- away eyewash flush mounted in the wall and ceiling with concealed piping:

a. Eyewash: Dual automatic pressure regulated polished chrome plated brass eyewash heads and assembly folds up flush into a wall mounted recessed stainless steel cabinet. Shower: Accessible shower activation by pull lever handle located 42 to 45 inches above the finished floor, installed inside of a wall mounted recessed stainless steel cabinet with exposed shower head. [Required in all Science and Industrial Arts Rooms. Unit is disabled accessible when eye/face wash spray outlet is mounted with a height of 36 inches].

1. HAWS - Eyewash & 8355 WC.SP38 Drench Shower special order w/ 20 GPM exposed SS flow control shower head.

2. GUARDIAN GBF 2150.

3. Or Equal.

NOTE TO ARCHITECT: Recessed model of the Combined Emergency Eyewash/Emergency Shower, No. EEW-1 is recommended. If wall space and wall depth do not allow for the recessed unit, then surface mounted, No. EEW- A, may be selected. PLEASE EDIT

THIS SPECIFICATION.

22 42 00

Revised: 01/07/22 Page 13 of 65 Plumbing Piping Section 22 42 00

2. EEW-1A: Eyewash: Disabled accessible eye/face wash, with an all stainless steel enclosure and bowl, twin eye/face wash spray heads with spray head covers and built-in flow control regulation, chrome-plated brass stay open valve with stainless steel valve stem, stainless push-paddle type handle. Shower:

Drench Shower with exposed stainless steel showerhead with recessed pull down level valve. [Required in all Science and Industrial Arts Rooms. Unit is disabled accessible when eye/face wash spray outlet is mounted with a height of 36 inches].

a. HAWS - Eyewash - 7752 WC, Drench Shower - 8165

b. CHICAGO - 9007, 9106-N5

3. EEW-2: Hand-held emergency eye/face wash. [Required in all Science Prep Rooms].

HAWS 8905

CHICAGO 9310-NF

2.12 ELECTRIC WATER COOLERS

1. EWC-1: Floor-mounted, thermostatically controlled, capacity not less than 14 GPH at 40 degrees F.; inlet water: 80 degrees F., ambient temperature: 90 degrees F.; furnished with chrome-plated close coupled fork type pushback glass filler.

Cabinet shall be not less than 20 gauge welded steel construction with enclosed base; 18-8 or equal stainless steel or chrome-plated strainer; hermetically sealed condensing unit shall be capable of handling specified capacity without overload, and motor shall be not less than 1/5 HP single phase 60 cycle 115 volts wired automatic controls. Water cooler shall comply with requirements of the governing agency or health department. (Specify for Middle and High Schools.)

HAWS HF-14-3139

ELKAY EFA-14

2. EWC-2: Same as EWC-1 except cooler shall be rated at 8 GPH.

(Specify for Elementary Schools.)

HAWS ELKAY

HF-14-3139 EFA-14

22 42 00

Revised: 01/07/22 Page 14 of 65 Plumbing Piping Section 22 42 00

3. EWC-3: Wall-mounted electric chiller type UL listed for physically handicapped and complying with Title 24 with minimum capacity of 8.0 GPH certified to comply with ARI Standard 1010/73. Fountain shall be furnished with stainless steel apron and cabinet push bar operated bubbler, automatic stream regulator, brass P-trap, and hermetically sealed, air-cooled condensing unit with 115 volt, single phase 1/5 HP motor with thermal overload protection. Provide with approved 3-wire grounding cord and connector, Hubbell No.

5264 or equal.

HAWS ELKAY

HWCA8-SS EHFA-8

4. EWC-4: With platform pushdown glass filler. (Specify for use in Faculty Dining Room - High School, Middle School, and Elementary School.)

HAWS

HWBFA8

5. EWC-5: Dual-height electric water cooler, same mechanical specification as EWC-3 except fully disabled accessible, with dual height stainless steel drinking fountains sharing a common waste, water supply and refrigeration.

HAWS

HWBFA8LSS

2.13 FAUCETS

1. F-1: 3/4 inch hose end faucet with vacuum breaker and top wall brace, rough chrome. (Specify for service sink.)

CHICAGO

445 (less spout – 897S

2. F-2: Chicago No. 517-GC double-jointed spout and mixing assembly for both hot and cold water 1/2 inch international pipe size female inlet shanks and integral check stops. Furnish with No. 369 handles and E-1 soft flow spout end. Exposed piping on range side shall be assembled with hospital threads or sleeves, which completely cover threads.

22 42 00

Revised: 01/07/22 Page 15 of 65 Plumbing Piping Section 22 42 00

3. F-3: Double faucet, rough-plated brass with vacuum breaker top brace and hose end. (Specify for can washing installation).

a. Elementary Schools: Wall-mounted with spout at 64 inches above finish floor.

b. Middle Schools: Mount on top of range shelf with 18 gauge stainless steel vertical backing plate with a horizontal flange fastened to range shelf. Plate shall be drilled to accommodate water supply nipples.

Pipe shall be securely fastened to backing plate. Lock nuts or waste nuts may be furnished. Spout end shall be at 64 inches above finish floor.

KOHLER CHICAGO

K-8907 305-VB-RCF

4. F-4: Self-closing metering, single lavatory fitting, adjustable time cycle and chrome-plated finish. Chicago 333-669 with E12 aerator.

2.14 FLOOR DRAINS

A. Schedule Numbers:

1. FD-1: Cast iron body, no hub with seepage pan and flat, round nickel bronze strainers not less than 5 inches diameter for 2 inches outlet bodies, 7 inches for 3 inches outlet bodies and 8 inches for 4 inches outlet bodies, with maximum of 1/2 inch square holes or slots not larger than 1/4 inch x 1-1/4 inch.

(Specify for use in locations other than tile floors.)

SMITH ZURN

2005Y-A ZN-415-B

2. FD-2: Same as specified for FD-1, except with square tops.

(Specify for use in tile floors.)

2005Y-B ZN-415-S

3. FD-3: Area type with 8-inch diameter minimum cast iron top grate (no hub). Drain shall be vandal-proofed by securing grate to body with stainless steel Allen flat-head screws.

2110-Y-U Z-550-VP

22 42 00

Revised: 01/07/22 Page 16 of 65 Plumbing Piping Section 22 42 00

4. FD-4: Pavilion type with cast iron hinged top, with removable sediment bucket. Drain shall be vandal-proofed by securing grate to body with stainless steel Allen flat head screws. No hub; 4-inch drain in lunch area in lieu of clarifier.

2230-Y-H-U Z-610-H-NH-UP Z-541-NH-VP-H

22 42 00

Revised: 01/07/22 Page 17 of 65 Plumbing Piping Section 22 42 00

5. FD-5: Gang shower, cast iron body with 5-inch diameter nickel-bronze vandal-proof strainer. No hub.

2005-Y-NB-U-(A) ZN-415- B-VP

6. FD-6: For indirect waste. Cast iron body with vandal-proof nickel-bronze top and funnel. No hub.

3510-F11-NB5 ZN-415-E

7. FD-7: Drain parking garage (emergency drain) with cast iron body, flashing collar and cast iron tractor grate. No hub, vandal-proof top.

2120Y-U ZN-508-9” VP

8. FD-8: Area drain, cast iron body, round pedestrian grate set in square frame.

1470Y-U-NB ZN-158-VP

9. FD-9: Planter drain, cast iron body, secured bronze dome with stainless steel mesh screen.

SMITH WITH 2646Y ZURN ZRB-352 with Z-1040 adaptor

2.15 FIRE HYDRANTS

1. FH-1: City of Fontana and/or County of San Bernardino Fire Department approved; 2-1/2 inches x 4 inches.

RICH 550 2-1/2” X 4”

MUELLER 2-1/2” X 4”

JAMES JONES J-3700

2.16 FIRE HOSE CABINETS

A. Schedule Numbers:

1. FHC-1 Cabinet: Semi-recessed type center break door with lock and decal "BREAK GLASS IN CASE OF FIRE" with 75-foot polyflex hose. Furnish Portable Extinguishers in each cabinet.

22 42 00

Revised: 01/07/22 Page 18 of 65 Plumbing Piping Section 22 42 00

Extinguisher shall be same as specified in Section 10 44 13: Fire Extinguishers and Cabinets.

CROKER W-1500 Series

2. FHC-2: Same as FHC-1 but surface mounted for masonry walls.

POTTER-ROEMER 1000 Series

2.17 FIRE HOSE VALVES

A. Schedule Numbers:

1. FHV-1 Valve, Fire Hose: Cast brass angle valve, UL and factory mutual approved; 1-1/2 inch size at 175 pounds; male or female ends.

POTTER-ROEMER 4070

POWHATTAN 15-158

UNITED 88

2. FHV-2 Valve, Fire Hose: Regular weight angle valves 1-1/2 inches, 2 inches and 2-1/2 inches for 150 or higher psig working pressure, female outlet for hose rack installation. Cast brass, replaceable composition disc, rough chromium-plated body with hand wheel.

POWHATTAN 18-157

UNITED 88H

POTTER-ROEMER 4065

2.18 FLEXIBLE HOSES

A. Schedule Numbers:

1. FLH-1: Corrugated stainless steel metal hose (for gas use). US Flex, or equal.

2. FLH-2: Corrugated bronze metal hose (for water use). US Flex, or equal.

2.19 FLUSH VALVE ASSEMBLY

A. Schedule Numbers:

1. FLV-1: Flush valves shall be of the filtered diaphragm quiet flush type. Diaphragm of nominal 3 inches diameter. Valves shall be furnished so that flush will remain constant and not

22 42 00

Revised: 01/07/22 Page 19 of 65 Plumbing Piping Section 22 42 00 require any adjustment or have any adjusting device. Flush valve for urinals shall deliver 1/2 to 1 gallon at each operation at any pressure from 5 pounds to 100 pounds, with handle held in any position. Flush valve for water closet shall deliver

1.6 gallons at each operation.

a. Silencing feature at flush valve shall be in valve proper and in associated stop. Silencing feature shall allow flush valve to flush and close quietly without restricting flow of water.

b. Each flush valve shall be provided with a loose key, square shank, lock shield angle service stop connected to flush valve with a union connection and adjustable nipple. Stops shall be furnished with vandal-proof caps.

c. Provide l7 gauge pressed brass escutcheons for wall and fixture. Escutcheons shall be fastened to not turn or rattle.

d. Each flush valve shall be furnished with a vacuum breaker providing one inch opening to atmosphere, which will not leak under any degree of back pressure and will not restrict rate of flow more than 10% at 10 pounds pressure and will operate noiselessly.

e. Tailpiece shall be not lighter than 17 gauge and shall be part of flush valve assembly.

f. Exposed metal parts of flush valve assembly to be nickel and chromium- plated on a brass or copper base.

2.20 FLOOR SINKS

A. Schedule Numbers:

1. FS-1: Round, cast iron, acid-resistant enamel body with bottom aluminum dome strainer, less grate. (Specify for use in Middle School and High School Multi-purpose Buildings and Cafeteria Buildings.)

SMITH 3400Y-10

ZURN Z-1950-1

2. FS-2: 6 inches to 8 inches deep, square cast iron acid-resistant enamel, bottom aluminum dome strainer with nickel bronze rim and grate top. (Specify for use in Middle School and High

22 42 00

Revised: 01/07/22 Page 20 of 65 Plumbing Piping Section 22 42 00

School Multi-purpose Buildings, High School Cafeteria and Mechanical Equipment Rooms.)

SMITH ZURN

3140Y Z-1901

3150Y ZN-1900

3. FS-3: Round, cast iron body with dome bottom strainer, under deck clamp and 2-inch high water dam; no hub type.

(Specify for outdoor use near cooling tower, near rooftop A/C unit, chillers, Mechanical Equipment Rooms.)

SMITH 3980Y-C

ZURN Z-108-RC

2.21 GARBAGE DISPOSAL UNITS

1. GD-1: Domestic type. (Specify for Middle School Food Rooms).

BIG GENIE NC-45

INSINKERATOR Model 1/2 HP 77

2. GD-2: (Specify for commercial type for Elementary School

Cafeteria kitchen). Waste King, Big Genie, or Insinkerator assemblies furnished with required components including the following:

a. Pulverator unit with 1/2 HP, 120 volt, single phase 60 cycle motor; motor to have built-in overload protection. Unit shall be supplied with water tapping into pulverator chamber or discharge of lower chamber, and with stainless steel cutting chamber.

b. Cone sink assembly, 18 inches diameter 16 gauge stainless steel, complete with stainless steel bowl cover, internal swirl and safety baffle.

c. Mounting assembly with splash-proof reversing switch assembly, 1/2 inch Jackes-Evans Type 3P solenoid valve, adjustable mixing tee for pre-rinse supply with built-in check valves, pre-rinse assembly consisting of flexible metal hose, coil spring, swivel connection hand grip valve, spray nozzle and wall brace.

1) I.S.E. SS-50

22 42 00

Revised: 01/07/22 Page 21 of 65 Plumbing Piping Section 22 42 00

3. GD-3: (Commercial type for Middle School Cafeteria kitchens, same as GD-2, except:)

a. Pulverator unit with 3/4 HP, 208/230 or 240 volts as required, 3-phase 60 cycle motor to match electrical service available. Motor shall have built-in overload protection. Unit shall be furnished with water tapping into pulverator chamber or discharge to lower chamber and without adjustable mixing tee and pre-rinse assembly.

1) I.S.E. SS-75

2.22 GREASE TRAPS (INTERCEPTORS)

A. Schedule Numbers:

1. GT-1: Cast iron, basket baffle assembly.

ZURN Z-1170

SMITH 8000 Series

2. GT-2: Pre-fabricated reinforced concrete with cast iron fittings, with manholes brought to grade. Size and capacity as indicated on Drawings. Brooks, Jensen, or Procast.

2.23 HOSE BIBS

A. Schedule Numbers:

1. HB-1: For plaster or stucco wall, furnished with box and stop, exposed trim chrome-plated, without door and with vacuum breaker. (Specify for use in swimming pool area, outside eating area and 75 feet spacing around exterior building wall.)

ACORN ZURN

8141 1350-5-LD

2. HB-2: For brick and poured concrete wall, furnished with box and stop, exposed trim chrome-plated, without door and with vacuum breaker. (Specify for use in swimming pool area, outside eating and 75 feet spacing around exterior building wall.)

ACORN ZURN

8141 1350-5-LD

22 42 00

Revised: 01/07/22 Page 22 of 65 Plumbing Piping Section 22 42 00

3. HB-3: ASTM B 62 bronze body, rubber composition disc or renewable set, straight nose with brass die cast or enamel iron handwheel. (Specify for use in Latch House.)

8131RBVB Z-1343-VB

4. HB-4: Same as HB-3 except furnish loose key stop and lockshield. (Specify for use at animal washdown area.)

8131LK-RBVB Z-1343-VB-LK

5. HB-5: Same as HB-3 except furnish with bent nose. (Specify for use at roof top AC Unit. Mechanical Equipment Room, Boiler Rooms, etc.)

8126-RBVB Z-1343-VB-LK

6. HB-6: Same as HB-4 except furnish with bent nose. (Specify for use in Agricultural Plot.)

8126LK-RBVB Z-1343-VB-LK

7. HB-7: Renewable seat, rough chrome finish, bronze body, flanged 3/4 inch I.P.S. Female thread inlet, loose key, with vacuum breaker.

CHICAGO WOODFORD

No. 387-E-27 No. 24P-CH-TK

8. HB-8: Recessed hose box furnished with wall flange and built-in drip lip. Box shall be one piece construction; door shall have a recessed cam lock. Door shall remain up and out of the?

when in fully opened position. Valve shall be replaceable loose key wheel handle and screwdriver stop. Install per manufacturer’s recommmendation. (Specify for use in Toilet Rooms.)

ACORN SMITH

8140 5509 QT-SAP

2.24 IRRIGATION SPRINKLER (SPECIFY FOR LATH HOUSE)

A. Schedule Numbers: IS-1, THOMPSON 170, CHAMPION 17.

22 42 00

Revised: 01/07/22 Page 23 of 65 Plumbing Piping Section 22 42 00

2.25 LAVATORIES

A. Schedule Numbers: Exposed trim shall be free from sharp edges or points. Fixture shall be furnished with other listed manufacturer specified trim. Instead of solid supply pipe, polished chrome-plated risers, 3/8 inch outside diameter with ferrule stop end and metal nosepiece may be furnished.

1. L-1: 20 inches x 18 inches cast iron, acid-resistant enamel punched with one hole only, 4 inches or 5 inches right of center and supplied with tempered or cold water only.

Furnished with hangers. Stops shall be loose key, square shank, lock shield type. (Specify for use in Student Toilet Rooms, Typing, Math, and Industrial Art Rooms.)

KOHLER CHICAGO MOEN ZURN

Bowl K-2810 Faucet 333-669 Drain 327A 14526

Supply

ZH-

8826-

LR-LK

Note: 1/2-inch I.P.S. x 3/8-inch comp.; female outlet.

2. L-2: Same as L-1, (Specify for handicap student use).

3. L-3: 20 inches x 18 inches cast iron, acid-resistant enamel, with center set combination faucets with lever handles and supplied with hot and cold water (for handicap use), complete with hangers.

KOHLER CHICAGO MOEN

Bowl K-2849

Faucet K-7404-E 802A 8145 Drain K-13885 14526

Supply 1017

Note: Insulate hot water and drain lines under lavatories and sinks with Armaflex wrap type insulation, 1/8 inch thick, 2 layers minimum with 50 percent overlap.

(Specify for handicapped use for L-3.)

4. L-4: 20 inches x 18 inches cast iron, acid-resistant enamel, with center set combination faucets with cross handles supplied with hot and cold water complete with hanger. (Specify for School Personnel, Administration Office, Cafeteria, Health Unit, 22 42 00

Revised: 01/07/22 Page 24 of 65 Plumbing Piping Section 22 42 00 etc.)

KOHLER CHICAGO MOEN

Bowl K-2849

Faucet K-7404 802A-633 8141 Drain K-7715 327A

Supply 1017

B. L-5: 16 inches x 14 inches (or size as indicated on Drawings), enamel cast iron, complete with combination supply and drain fitting. (Specify for use in High School Student Store and 1959 Portable Bldg.)

KOHLER CHICAGO

Bowl K-2485

Faucet K-8046-4A 105-317 Drain

Supply 442-LK

2.26 LABORATORY GAS VALVES

A. Schedule Numbers:

1. LGV-1: Ground key stop, heavy chrome-plated, nickel and copper composition, double turret at 90 degree angle 3/8 inch international pipe size deck type, with lever handle and vandal-proof plastic index button. (Specify for use in Middle School Science Room countertop tables.)

CHICAGO

982-909C

2. LGV-2: Laboratory gas valve, same as LGV-1, except single turret. (Specify for use in Middle School Science Room demonstration table.)

CHICAGO

980-909C

3. LGV-3: Same as LGV-1, except double turret at 180 degree angle. (Specify for use in High School Chemistry, Physiology, Biology, Physics, Modern Science and Science Room peninsula table.)

981-909C

4. LGV-4: Ground key stop, heavy chrome-plated, nickel and copper composition, single turret, wall-mounted, 3/8 inch

22 42 00

Revised: 01/07/22 Page 25 of 65 Plumbing Piping Section 22 42 00 international pipe size with lever handle and vandal-proof plastic index button. (Specify for use in Middle School Science Work Rooms.)

CHICAGO HAWS

986-909C 6046-6030

5. LGV-5: Heavy chrome-plated, single turret assembly, nickel and copper composition, 1/2 inch iron pipe size concealed angle stop with extended stem and spoke handle with vandal-proof plastic index button. (Specify for use in High School Chemistry Room fume hood.)

962V0G-980-E7T

2.27 LAUNDRY TRAYS

1. LT-1: Cast iron, acid-resistant enamel, with strainer and 1-1/2 inches tubing tailpiece, 24 inches x 21 inches x 13-1/2 inches in cabinet top, with faucet, strainer and tray. (Specify for use in High School and Elementary Special Education DH Storage/Laundry Room.)

CHICAGO KOHLER MOEN

Tray K-6757 Faucet 1100 K-7761-T 8133 Strainer K-8821 8133W/S0007

2. LT-2: Cast iron, acid-resistant enamel, 24x 20 inches x 13 inches, black angle frame, with faucet strainer and tray.

MOEN KOHLER CHICAGO

Tray K-6757

Faucet 8120 445 Strainer W/S0001

2.28 PIPE HANGERS

A. Refer to Section 23 05 13: Basic Mechanical Materials and Methods.

B. Schedule Numbers:

1. PH-1: Complete with clamps, inserts, etc.

22 42 00

Revised: 01/07/22 Page 26 of 65 Plumbing Piping

SUPERSTRUT UNISTRUT B-LINE

2. PH-2: In shower area.

a. ACORN 7116 or 7118 series, or equal.

2.29 P-TRAPS

A. Schedule Numbers:

1. PT-1: Cast brass complete, chrome-plated.

ZURN Z-8712-LC

2.30 PRESSURE REGULATING VALVE ASSEMBLIES

A. Schedule Numbers:

1. PRV-1: Furnish for water service, all bronze body, stainless steel seat, bronze strainer, calibrated springs, corrosion resistant, adjustable control for water service.

WATTS WILKINS

ACV Series 500 XL45BR

2. PRV-2: Furnish for air service, Japanned steel, spring loaded, brass forging body, nylon reinforced neoprene diaphragm, inlet pressure up to 250 pounds, reduced pressure 5 pounds to 60 pounds.

MASON-NEILAN SCHRADER

71-1/2" 3464, 1/2"

3466, 3/4"

3. PRV-3: Furnish for gas service, spring-loaded model, Buna N rubber composition or leather valve seat disc and diaphragm, inlet pressure 125 pound maximum.

REPLIANCE FISHER

1813C S-100. 166-1, S-201, 166-2

4. PRV-4: Furnish for gas service for (unit heaters, boilers, and similar installations). Spring-loaded model, Buna N rubber composition, or leather valve seat and diaphragm suitable for temperatures to 150 degrees F.; maximum inlet pressure one pound. Outlet pressure 4 inches to 10 inches adjustable; orifice to suit. For pilot lines and main burners.

REPLIANCE MAXITROL HONEYWELL

22 42 00

Revised: 01/07/22 Page 27 of 65 Plumbing Piping Section 22 42 00

A3000 Series RV V5172 Series

2.31 ROOF DRAINS

1. RD-1: Low profile dura-coat cast iron body dome strainer type.

1010Y-ERC Z-100-ERC

2. RD-1A:

1010Y-R-C Z100-89-RC

3. RD-2: Cast iron body with standpipe. (Specify for use as overflow.)

1080Y-ERC Z-100-89-ERC

4. RD-2A:

1080-Y-R-C Z100-89-RC

2.32 SHOWER ASSEMBLIES

A. General: Shower assemblies shall be fastened to walls with 18-8 stainless steel Allen key or interrupted slot flat head machine screws with polished head of length sufficient for full thread engagement with steel plate in stud wall or minimum of 3/8 inch engagement with lead shields in concrete wall. When securing to shower racks furnish same machine screws with 18-8 stainless steel nuts and washers. Fittings valves and heads shall be recessed type to cover male pipe threads or male threads shall be hospital type plated after threading and installed with not more than one thread showing. Pipe, fittings, valves, and nozzles shall be chrome-plated with exception of headers.

B. Schedule Numbers:

1. SA-1: Wall-mounted shower and/or back to back shower, with built-in soap dispenser system. Housing shall be of 16 gauge, Type 304 stainless steel with exterior polished satin finish.

Shower shall be factory prepared and hydrostatically tested

22 42 00

Revised: 01/07/22 Page 28 of 65 Plumbing Piping Section 22 42 00 to 150 psi at the factory. Internal piping shall be Type L copper tubing. Fittings shall be cast bronze or copper, valves shall be tempered water and not to exceed 2.0 GPM. Flange showerhead shall be lockable universal ball joint. Exposed fasteners shall be tamper resistant. Shower station shall be 18 inches from each end and 36 inches on center and 74 inches vertical height, shower assembly shall be complete with mounting brackets and stanchions. (Specify for use in Middle Schools for Boys' and Girls' group shower; P.E. Buildings, see also SA-7 for new facility construction).)

ACORN BRADLEY

Wall-Mounted A-100 Series 1 PA Back-to-Back B-130 Series 2PA

2. SA-2: Double valve, vandal-proof, chrome-plated exposed type valve with chrome-plated handles and swivel discs;

chrome-plated brass pipe international pipe size supplies offset as required for installation; Flange shower head, single orifice and lockable universal ball joint. (Specify for use in Middle Schools for Male and Female Instructors P.E. Buildings)

ACORN 521 BRADLEY

3. SA-3: Same as SA-2 except single valve. (Specify for use in Middle Schools for Male and Female Instructors - P.E.

Buildings)

ACORN 525 BRADLEY

4. SA-4: (Specify for handicap use - Special Education Schools, High School Therapy Unit, Elementary School - DH Toilet Room, OH Toilet Room.)

a. Shower control valve: Polished chrome-plated metal lever handle; Symmons 021, or equal.

b. Vacuum breaker: Chicago 892-G exposed. Vacuum breaker for concealed piping, Zurn Z-80000-EVB.

c. Wall spout: Chicago 777-37KJK wall spout with 1/2 female i.p.s. flange inlet and 1/2 inch male i.p.s.

outlet, chrome-plated.

d. Hose and bar: 5-foot long reinforced white vinyl hose with 24-inch long adjusting bar with hand shower slide bracket, chrome-plated. Chicago 153-WV.

e. Hand shower: Insulated handle with central lever stop valve, bent nozzle tube; rubber bound hose spray

22 42 00

Revised: 01/07/22 Page 29 of 65 Plumbing Piping Section 22 42 00 adapted for 1/2 inch hose connection.

ACORN, BRADLEY, OR EQUAL

5. SA-5: Showerheads shall be square flanged type chrome-plated and exposed screws shall be vandal-proof showerhead shall be mounted with concealed back plate assemblies, valves vacuum breaker and nozzles shall be chrome- plated.

(Specify for handicap use - Elementary and Middle Schools in Nurse's Rooms.)

a. Showerhead: Showerhead shall be square flanged type with lockable universal ball joint. Acorn 802-2-YY, Bradley 445 LBJ, or equal.

b. Control valve: Concealed volume control with positive shutoff valve, modify with lever handle.

Acorn, Bradley, or equal.

c. Vacuum breaker: Exposed vacuum breaker assembly for concealed supply piping. Acorn, Bradley DV 892- G, or equal.

d. Diverter valve: Transfer flow between showerhead and hand held shower. Acorn 591, Bradley DV, or equal.

e. Hand-held shower: 5-foot long reinforced white vinyl hose with quick disconnect, nylon and chrome hand spray and 24-inch adjusting bar-with hand shower slide bracket. Acorn No. 151, Bradley, or equal.

f. Wall spout: Acorn, Bradley, or equal wall spout with 1/2 inch female i.p.s. flange inlet and 1/2 inch male i.p.s. outlet, chrome-plated.

6. SA-6: Showerheads shall be square flanged type chrome-plated and exposed screws shall be vandal-proof.

Showerhead shall be mounted with concealed back plate assemblies; valves and nozzles shall be chrome-plated.

(Specify for handicap use - Gymnasium Buildings - Middle Schools.)

a. Showerhead: Showerheads shall be square flanged type with lockable universal joint. Acorn-802-2-YY, Bradley 445 LBJ, or equal.

b. Control valve: Concealed volume control with positive shutoff valve, modify with lever handle, Acorn, Bradley, or equal.

22 42 00

Revised: 01/07/22 Page 30 of 65 Plumbing Piping Section 22 42 00

c. Diverter valve: Transfer flow between showerheads.

7. SA-7: (Specify for use in Middle Schools for Student Showers / fixed walls - P.E. Buildings)

a. Shower control valve: Polished push button automatic shower limiter metering valve installed concealed inside wall; polished chrome-plated with vandal proof screws for escutcheon mounting; Acorn, Bradley, or equal.

b. Shower head: Institutional showerhead with vandal resistant mounting, Acorn, Bradley, or equal.

8. SA-8: (Specify for handicap - Student)

a. Shower control valve: Polished push button automatic shower limiter metering valve installed concealed inside wall; polished chrome-plated with vandal proof screws for escutcheon mounting; Acorn, Bradley, or equal.

b. Vacuum breaker: Exposed vacuum breaker for concealed piping, Acorn, Bradley or equal.

c. Wall spout: Wall spout with 1/2 female i.p.s. flange inlet and 1/2 inch male i.p.s. outlet, chrome-plated;

Acorn, Bradley, or equal.

d. Hose and bar: 5-foot long, flexible, braided metal hose with 24-inch long adjusting bar with hand shower slide bracket, chrome-plated; Acorn, Bradley, or equal.

e. Hand shower: Insulated handle with central lever stop valve, bent nozzle tube; rubber bound hose spray adapted for 1/2 inch hose connection.

9. SA-9: (Specify for handicap - Faculty)

a. Shower control valve: Polished pressure balancing mixing valve with single blade level handle, integral volume control and chrome plated brass escutcheon; Acorn, Bradley, or equal.

b. Vacuum breaker: Exposed vacuum breaker for concealed piping, Acorn, Bradley, or equal.

c. Wall spout: wall spout with 1/2 female i.p.s. flange inlet and 1/2 inch male i.p.s. outlet, chrome-plated;

Acorn, Bradley, or equal.

22 42 00

Revised: 01/07/22 Page 31 of 65 Plumbing Piping Section 22 42 00

d. Hose and bar: 5-foot long, flexible, braided metal hose with 24-inch long adjusting bar with hand shower slide bracket, chrome-plated; Acorn, Bradley, or equal.

e. Hand shower: Insulated handle with central lever stop valve, bent nozzle tube; rubber bound hose spray adapted for 1/2 inch hose connection.

2.33 SERVICE SINKS

A. Schedule Numbers:

1. SS-1: Cast iron, conforming to Commercial Standard CS 77.63 for acid- resistant enamel, 22 inches x 18 inches, with blank back, outlet trap standard and rough-plated double faucet with top brace mounted above sink back, furnished with vacuum breaker and hose end.

KOHLER CHICAGO

Sink K-6718

Faucet 445-897

SRXKCCP

Trap Standard K-6673

2. SS-2: Molded stone mop basin, 36 inches x 24 inches x 10 inches, double faucet with vacuum breaker, pail hook, threaded spout and wall bracket. Also, furnished with mop hanger, bumper guard, flat strainer, hose and hose bracket.

(Specify for use in High School Support Custodial Room.)

ACORN KOHLER CHICAGO

Sink TRH-242410

Faucet K-8928 445-897S Rim Guard KBGS

Strainer included

2.34 SINKS

A. Cast iron sinks shall be acid resistant enamel, and shall conform to Commercial Standards CS 77.63. Units furnished in conjunction with strainer installation or faucet installation shall be brass. Exposed brass nuts shall be chrome-plated. Refer to the Fixture Supplies paragraph of this section.

B. Schedule Numbers:

1. S-1: Cast iron, flat rim, center outlet, single compartment, size as indicated on Drawings with crumb cup strainer and

22 42 00

Revised: 01/07/22 Page 32 of 65 Plumbing Piping Section 22 42 00 backsplash mounted double swing spout faucet, less soap dish. (Specify for use in High School Clothing Rooms.)

CHICAGO KOHLER MOEN

Sink K-6550 Faucet 540-LD-DJ 18 8121 W/S0012 Strainer K-8801

2. S-2: Cast iron, flat rim, end outlet, single compartment, size as noted on Drawings, with crumb cup strainer and backsplash mounted double swing spout faucets. Same as S-1. (Specify for use in Middle School Multi- purpose Buildings, Elementary School - Waiting Room). CECO No. 710.

3. S-3: Same as S-1, except with flat strainer. Kohler Strainer K- 8807 or American Standard 4311.023. (Specify for use in Middle School Library Workroom and Library Unit. - High School Library Workroom and Art Class.)

4. S-4: Same as S-2, except with flat strainer. Kohler strainer K-8807 or American Standard 4311.023. (Specify for use in Middle School Administration Office, Teacher Workroom, Faculty Lounge, and Attendance Office - Elementary School Small Conference Room).

5. S-5: Same as S-3, except with 2 single backsplash mounted swing spout faucets. Cold water to each faucet. Faucet - Chicago 332 E3. (Specify for use in Middle School and High School Special Education Classroom.)

a. ZURN-Z-875 F1

6. S-6: Same as S-4, except with 2 single backsplash mounted swing spout faucets. Cold water to each faucet. Faucet - Chicago 332. (Specify for use in High School Metal Shop and Woodworking Shop.)

a. ZURN Z-875 F1.