22-037 RFP ERATE CABLE RELOCAT
78 KB Posted
- Attached to
- (1) Tiltrotator
- Solicitation number
- 22-037
- Issued by
- Fayette County, Georgia
About this file
This is a Request for Proposals (RFP) issued by the Houston County Board of Education for cable relocation services across the district. The RFP seeks qualified vendors to perform network cabling labor that involves disconnecting and relocating existing data cable drops from walls to ceilings in classrooms throughout the district. The project encompasses approximately 1,976 classrooms across 31 schools, including elementary schools, middle schools, and high schools. The work involves removing designated drops, disconnecting existing cables, pulling cables into the ceiling, terminating drops into new keystone network jacks, testing and labeling installations, and providing 15-foot CAT 6 orange patch cords. The RFP was released on February 9, 2022, with proposals due on March 10, 2022, at 10:00 a.m. Eastern Time. The board indicated an intent to award on March 16, 2022, with work commencing on July 1, 2022. The initial contract term is one year or less from award through the end of the calendar year, with automatic annual renewals not to exceed 24 months unless cancelled in writing.
All cabling must comply with ANSI/TIA/EIA-568 standards and be capable of supporting minimum 1 gigabyte network applications. Materials must be new, with all components meeting Category 6a specifications, and installation must include comprehensive testing using industry-compliant equipment with detailed documentation of results. The vendor is responsible for all equipment delivery, site preparation, debris removal, damage repair, and restoration of the work area. Vendors must provide evidence of liability insurance with minimum coverage of $500,000 per occurrence for general liability and $500,000 per occurrence for automobile liability, naming the Houston County School District as additional insured. Proposals will be evaluated based on RFP response requirements (200 points), functionality (200 points), company background and experience (200 points), and cost (400 points). Vendor pricing must be held firm and cannot be adjusted after project award. Vendors must provide proof of E-Verify authorization and attest that they are not under red light status with SPIN registration.
Text of this file
HOUSTON COUNTY BOARD OF EDUCATION
REQUEST FOR PROPOSALS
For Cable Relocation
RFP NUMBER 22-037
For all questions about this RFP contact via email:
L. Renee Langston CPPB, Issuing Officer PH. - 478-988-6211 ext. 4
FAX – 478-988-6212
EMAIL – renee.langston@hcbe.net
RELEASED ON:
February 9, 2022
DUE ON:
March 10, 2022; 10:00 A.M. Eastern Time
1.0 INTRODUCTION
1.1 Purpose of Procurement
The Houston County Board of Education, hereafter referred to as the “District,” is requesting proposals to perform cabling labor to relocate drops inside classrooms throughout the district.
1.2 Proposal Certification
The Houston County Board of Education certifies the use of competitive sealed bidding will not be practical or advantageous to the Board in completing the acquisition described in this RFP. Competitive sealed proposals will be submitted in response to this RFP. All proposals submitted pursuant to this request will be made in accordance with the provisions of this RFP.
1.3 Schedule of Events
This Request for Proposals will be governed by the following schedule:
02/9/2022
Release of RFP
3/10/2022
Proposals due
3/16/2022
Intent to Contract Award
7/1/2022
Work may begin
1.4 Restrictions on Communications with Staff
All questions about this RFP shall be submitted in the following format:
Company Name
| 1. Question |
| Citation of relevant section of the RFP |
| 2. Question |
| Citation of relevant section of the RFP |
Questions shall be directed in writing to the Issuing Officer: renee.langston@hcbe.net Fax: 478-988-6212
From the issue date of this RFP until a Vendor is selected and the selection is announced, Offerors are not allowed to communicate for any reason with any Board staff except through the Issuing Officer named herein, or during the Offeror's conference, or as provided by existing work agreement(s). The Board reserves the right to reject the proposal of any Offeror violating this provision. All questions concerning this RFP shall be submitted in writing (fax or email may be used) to the Issuing Officer. No questions other than written will be accepted. No response other than written will be binding upon the Board. Questions and answers will be posted to the HCBOE website as they are received. Website address is http://www.hcbe.net/purchasing
1.5 Definition of Terms
Board – Houston County Board of Education Contractor – Respondent to this Request for Proposal District – Houston County Board of Education HCBOE – Houston County Board of Education OCGA – Official Code of Georgia Annotated (State Statute) Offeror – Respondent to this Request for Proposal RFP – Request for Proposal Vendor – Respondent to this Request for Proposal
1.6 Contract Term
Code section 20-2-506 of the laws of the State of Georgia as of this date and as may be amended apply to this agreement. If it is determined that a contract is established for this project, for the duration of the contract term established through this RFP, contracts will automatically renew on January 1 of each year unless notified in writing by HCBOE.
The initial contract term is one (1) year, or less, from contract award through the end of the current calendar year and will automatically renew not to exceed 2 years (24 months) unless cancelled as specified herein.
1.7 Background
For information on the Houston County Board of Education please go to www.hcbe.net.
1.8 Submission Expenses
The District shall not be liable for any expenses incurred by the Offeror in responding to this RFP. This shall include expenses incurred by the Offeror to conduct product demonstrations at the District site.
1.9 Right to Purchase
HCBOE reserves the right to purchase from any source to include existing or future state or federal contracts, cooperatives or from any submitted proposals.
2.0 MANDATORY REQUIREMENTS
This section identifies all mandatory requirements, which must be addressed in the proposal before further consideration will be given. Each response must reference the item number it is in reference to (i.e., 2.1.a, 2.1.b, etc.).
Project Objective Our objective is to prepare classrooms for future POE powered devices. Data drops currently being used for computers or printers will be relocated to the ceiling.
Cabling labor is defined as:
The district is seeking network cabling labor to perform the following:
Disconnect one existing data cabling drop in each designated room and relocate that drop to the ceiling. This procedure will include:
· Removing a designated drop in each classroom
· Disconnecting existing data cable from existing module
· Pull existing cable back into ceiling
· Terminate drop into new keystone network biscuit
· Test, identify drop number, and label biscuit (label ceiling grid?)
· Provide 15’ CAT 6 orange patch cord in ceiling
· Blank out original drop location
· Neatly coil and secure cable next to wall
· Estimated numbers of rooms is 1976 (see 22CableReloPricing.xls attachment).
· Locations to be Upgraded:
| School |
| Classrooms |
| Bonaire ES |
| 50 |
| Bonaire MS |
| 64 |
| Bonaire Primary |
| 67 |
| CB Watson PS |
| 46 |
| Centerville ES |
| 47 |
| David Perdue ES |
| 45 |
| David Perdue PS |
| 54 |
| Feagin Mill MS |
| 64 |
| Hilltop ES |
| 54 |
| Houston HS |
| 120 |
| Lake Joy ES |
| 54 |
| Lake Joy PS |
| 54 |
| Langston Road ES |
| 54 |
| Matt Arthur ES |
| 54 |
| Miller ES |
| 47 |
| Morning Side ES |
| 45 |
| Mossy Creek MS |
| 70 |
| Northside ES |
| 45 |
| Northside MS |
| 56 |
| Northside HS |
| 112 |
| Park Wood ES |
| 48 |
| Pearl Stephens ES |
| 40 |
| Perry HS |
| 82 |
| Perry MS |
| 64 |
| Quail Run ES |
| 59 |
| Russell ES |
| 49 |
| Shirley Hills ES |
| 47 |
| Thompson MS |
| 64 |
| Veterans HS |
| 105 |
| Warner Robins HS |
| 109 |
| Warner Robins MS |
| 59 |
| Westside ES |
| 48 |
2.1 GENERAL
2.1.1 Vendor’s personnel shall be uniformed or identifiable at all times while on HCBOE locations. Necessary badges needed for building entry will be provided by the District.
2.1.2 Collect customer data including cable containment information, outlet location, rack information and labeling requirements prior to delivering service onsite.
2.1.3 Equipment needed to complete this project shall be delivered onsite by the successful Vendor at no added expense to HCBOE.
2.1.4 Provide manufacturer manuals or user guides in electronic format.
2.1.5 All equipment and materials shall be new. Used, re-conditioned or refurbished equipment and materials shall not be accepted.
2.1.6 All components and installation methods shall be EIA/TIA 568 approved and conform to EIA/TIA 569 practices and methods. The cabling system installed by the Vendor shall be capable of a minimum of 1 gigabyte network application.
2.1.7 Vendor shall assume all responsibility to repair or replace fixtures and/or materials damaged during its work on the this project, including but not exclusively, ceiling grip and tiles, gypsum boards, etc. Vendor shall be wholly financially responsible for damages realized by HCBOE as a result of the Vendor’s activities.
2.1.8 Vendor is responsible to reconnect any utilities, equipment, system furniture panels or trim, or appliances removed in the course of work, and replace all furniture, etc. moved for the performance of this project. All debris and rubbish created to complete project shall be removed by the Vendor. Site shall be left in a clean, neat, and orderly manner.
2.1.9 In lieu of a walkthrough, a detailed plan of each locations and drops has been included with this RFP.
2.1.10 Existing wired systems, i.e. intercom, alarm, cable TV, etc. shall be maintained during the installation and shall not be removed or damaged during the cabling removal and replacement.
2.2 MATERIALS AND INSTALLATION
| 2.2.1 | All cabling will be installed and terminated in accordance with the ANSI/TIA/EIA-568 standards unless otherwise requested prior to installation. |
| 2.2.5 | All category 6 patch cords shall be constructed with a snag less boots to T568B plug wiring format and will be 100% factory manufactured. |
| 2.2.6 | Fabrication of patch cords in the field is prohibited. |
| 2.2.7 | Jack shall meet or exceed the Category 6a/Class E for ISO/IEC and TIA/EIA 568.B2-1 specifications. |
| 2.2.8 | Jacks will be terminated according to the T568B wiring scheme, and follow industry standard 110 IDC. |
| 2.2.9 | All new drops installed will require new faceplates and jacks. Ortronics parts are the preferred brand for all keystone jacks, faceplates, and patch panels or equal. |
| 2.2.10 | All Cat 6 patch cables (15’) shall be provided 1 per drop added. |
| 2.2.12 | All cabling will be properly tested for continuity, return loss (RL) and near-end cross talk (NEXT), and an electronic copy of the test results shall be provided. |
| 2.2.13 | All cabling will be labeled at both the patch panel and terminated ends. |
| 2.2.14 | All labeling will conform to a uniform standard throughout the building. |
| 2.2.19 | Where possible all cabling should use existing pathways. |
| 2.2.20 | When conduit is not available in a location, the installation of wire molding will be required. |
| 2.2.21 | Flexible sleeve(s) shall be placed above the false ceiling to link buildings where construction is of modular building design (having air space between closely set buildings). The sleeves shall be large enough to adequately hold all cabling and provide extra room for future growth. The connection shall be weather tight. |
| 2.2.22 | If drops penetrate a fire rated wall, then the wall shall be restored to rating. |
| 2.2.23 | Cable supports shall provide a bearing surface of sufficient width to comply with required bend radii of high-performance cable. |
| 2.2.24 | Cable supports shall have flared edges to prevent damage while installing cables. |
| 2.2.26 | All outlets in modular furniture will be installed with the correct faceplate to match furniture manufacturer for the exact fit. Outlets in walls shall be matched to existing electrical trim plates. |
| 2.2.27 | Cables in modular furniture shall be routed in internal pathways dedicated to data cables. |
| 2.2.28 | Vendor shall be responsible for labeling which shall be uniform throughout each location. Items that will be labeled include: |
· Workstation jacks and faceplates
· Panels and shelves
· Closet hardware such as patch panels, blocks, shelves, racks, etc.
· Other applicable telecommunications and audio visual devices, workstation cable on both ends
2.2.29 All cables will be tested and certified with an industry compliant tester (e.g. Fluke DTX-1800 tester). The tester shall be equipped with the latest Cat 6a software available. The tester will measure the electrical characteristics of the cable using a true frequency sweep method, similar to that of high-end laboratory style testing equipment. Each test will be conducted from the Horizontal or Cross-connect to the workstation outlet. All cable pairs and terminations will be tested for continuity including shorts, opens, crosses, splits, and wire mapping. In addition, each cable test will be documented with its actual performance results in the following areas:
· Length (ft.)
· Impedance (ohms)
· Resistance (ohms)
· Capacitance (pF)
· Attenuation (dB)
· Near End Cross Talk (NEXT)
· Power Sum Near End Cross Talk (PS-NEXT)
· Power Sum Far End Cross Talk (PS-FEXT)
· Return Loss (RL)
· Delay Skew (DS)
· Pair to pair Power Sum Cross Talk (ELFEXT)
· Attenuation to Crosstalk Ratio (ACR)
· Power Sum Attenuation to Crosstalk ratio (PS-ACR)
| Hard copy and Excel file of results for each UTP Cat 6a, 4-pair cable will be submitted as part of cabling system project performance acceptance records. In addition to the above information, the documentation will also include a pass indication for the specified cable, the test date and the serial number, make and model number, and software version of the scanner. | |
| 2.2.30 | Replaced wiring is to be removed to source of supply by the Vendor. |
| 2.2.31 | When required, Vendor shall remove, relocate, and extend existing installations to accommodate new construction. |
| 2.2.32 | Remove exposed abandoned conduit, including abandoned conduit above accessible ceiling finishes. Cut conduit flush with walls and floors and patch surfaces. |
| 2.2.33 | Disconnect replaced outlets and remove devices. |
| 2.2.34 | Repair any damage to finishes that were caused by the Vendor during installation. |
2.2.35 Repair all damages to the building due to the negligence of its workers.
2.2.36 Replace any broken equipment with equal or greater value to be determined by HCBOE.
2.2.37 Dispose of all hazardous material in accordance with federal, state, and local requirements.
2.2.38 Vendor must leave the premises clean and neat including having all ceiling tiles in place after each workstation.
2.2.39 Cabling shall not be laid on ceiling grid structure, ceiling tiles or supported on any structure not specifically designed for supporting cables. If a cable tray is not present, provide cable supports at intervals of every 4‐6 feet. Cable supports shall be “J” hooks or other supporting devices with a minimum 1‐inch cable resting surface. Cable support devices shall be independently from or attached to building structure or walls. Cable sag between supports shall not exceed 12 inches. All cables shall be neatly bundled and secured with appropriately rated fasteners.
2.2.40 Cables should not be installed within 4‐feet of transformers/motors, when running parallel of power conduits or fluorescent light fixtures maintain a 1 foot separation.
2.2.41 Color code ports and cable per coordination with HCBOE.
2.3 Company Background and Experience
Offeror will describe their background, relevant experience, and qualifications, including, but not limited to the following:
2.3.1 Company Structure
The Offeror will include in the proposal the legal form of their business organization, the state in which incorporated (if a corporation), the types of business ventures in which the organization is involved and the office location that will be the point of contact during the term of any resulting contract.
2.3.2 Experience
The Offeror shall include in the technical proposal the number of full consecutive years they have been operating under their current business name.
The Offeror will provide a list of at least 3 clients for whom similar services, as detailed in this RFP, have been provided during the past three years. The list must include:
· dates of service
· name of contact person
· title of contact person
· phone number of contact person
The Offeror will also disclose any services terminated by the client(s) and the reason(s) for termination.
2.3.3 Vendor shall be responsible for complying with all Federal, State, County, and City laws, codes, and ordinances applicable to the performance of any work resulting from this RFP. Vendor shall be required to adhere to all applicable local environmental ordinances. Ignorance on the part of the Vendor will in no way relieve the Vendor from responsibility.
2.3.4 Vendor shall be responsible for obtaining all required permits applicable to performance under any single order placed against this RFP. Cost of any permits required are the sole responsibility of the Vendor.
2.3.5 Vendor must be provide a name and contact number of the Vendor’s Project Manager that will be available during complete install.
2.3.6 Exact measurements are not available and will be the Vendor’s responsibility to estimate based upon a typical classroom size and the number of locations designated in this RFP. Vendor’s prices quoted must be held firm and shall not be adjusted after project has been awarded.
2.3.7 Vendor shall include a SPIN certifying they are a registered service provider and must respond to this item confirming they are not under red light status.
3.0 PROPOSAL SUBMISSION AND EVALUATION
3.1 Process for Submitting Proposals
3.1.1 Preparation of Proposal
Each proposal should be prepared simply and economically, avoiding the use of elaborate promotional materials beyond those sufficient to provide a complete presentation. If supplemental materials are a necessary part of the technical proposal, the Offeror should reference these materials in the technical proposal, identifying the document, and citing the appropriate section and page(s) to be reviewed.
3.1.2 Packaging of Proposal
The Offeror's proposal in response to this RFP must be divided into two appropriately labeled and sealed packages - a Technical Submission and a Financial Proposal.
Include original and one (1) copy of technical submission and one (1) copy of the financial proposal. In addition, submit digital copy of all documents on USB flash drive with the financial response form in EXCEL format only. Do not include cost information in the technical submission.
The contents of each package will include:
Technical Submission Proposal Certification (Attachment A) Immigration and Security Form (Attachment B) Certificate Regarding Debarment, Suspension, Ineligibility (Attachment C) Contract Exceptions (Attachment D) Technical Proposal, addressing all requirements in Section 2.0
Financial Proposal The Offeror must use the Financial Proposal Form provided as a part of this RFP. Each location must be proposed separately as designated on form.
Mark the outside of shipping package as follows:
Name of Company Phone Number and Point of Contact for Company
RFP # 22-037
Due March 10, 2022; 10:00 A.M. Eastern Time
3.1.3 Submission of Proposals
Proposals must be submitted to:
HCBOE – Purchasing Dept.
L. Renee Langston, CPPB 200 Jerry Barker Drive Warner Robins, Georgia 31088
Any proposal received after the due date and time will not be evaluated.
3.2 Evaluation Process
The evaluation of proposals received on or before the due date and time will be conducted in the following phases.
3.2.1 Administrative Review
The proposals will be reviewed by the Issuing Officer for the following administrative requirements:
· Submitted by deadline
· Separately sealed Technical Submission and Financial Proposal
· All required documents have been submitted
· Technical Submission does not include any information from the Financial Proposal
· All documents requiring an original signature have been signed and are included
3.2.2 Proposal Evaluation
Proposals, which pass the Mandatory Requirements Review, will be reviewed by the Technical Evaluation Team for quality and completeness.
The following are the maximum possible points of each category:
| RFP Response Requirements |
| 200 Points |
| Functionality |
| 200 Points |
| Company Background ,Experience, and eRate History |
| 200 Points |
| Cost |
| 400 Points |
3.2.3 Oral Presentations
The Board reserves the right to choose and invite Offerors to present their technical solution to the Technical Evaluation Team. The Financial Proposal must not be discussed during the oral presentation. All Offerors submitting proposals may not be asked to make a presentation.
3.2.4 Financial Proposal Evaluation
Offerors shall use only the Financial Proposal Forms provided with the RFP.
3.2.5 Identification of Apparent Successful Offeror
The resulting Financial Proposal scores will be combined with the Technical Proposal score. The Offeror with the highest combined technical and financial score will be identified as the apparent successful Offeror.
3.3 Rejection of Proposals/Cancellation of RFP
The Board reserves the right to reject any or all proposals, to waive any irregularity or informality in a proposal, and to accept or reject any item or combination of items, when to do so would be to the advantage of the Board. It is also within the right of the Board to reject proposals that do not contain all elements and information requested in this document. The Board reserves the right to cancel this RFP at any time. The Board will not be liable for any cost/losses incurred by the Offerors throughout this process.
4.0 TERMS AND CONDITIONS
4.1 RFP Amendments
The Board reserves the right to amend this RFP prior to the proposal due date. All amendments and additional information will be posted to the HCBOE Purchasing website, located at: http://www.hcbe.net/purchasing. Offerors are encouraged to check this website frequently.
4.2 Proposal Withdrawal
A submitted proposal may be withdrawn prior to the due date by a written request to the Issuing Officer. A request to withdraw a proposal shall be signed by an authorized individual.
4.3 Cost for Preparing Proposals
The cost for developing the proposal is the sole responsibility of the Offeror. The Board will not provide reimbursement for such costs.
4.4 Sample Contract
The Sample Contract, which the Board intends to use with the successful Offeror, is attached to this RFP and identified as Attachment D. Exceptions to the Contract should be identified and submitted with the Offeror's proposal. Proposed exceptions must not conflict with or attempt to preempt mandatory requirements specified in Section 2.0.
Prior to award, the apparent winning Offeror will be required to enter into discussions with the Board to resolve any contractual differences before an award is made. These discussions are to be finalized and all exceptions resolved within one (1) week of notification. Failure to resolve contractual differences will lead to rejection of the Offeror's proposal.
The Board reserves the right to modify the Contract to be consistent with the successful offer and to negotiate with the successful Offeror other modifications, provided that no such modifications affect the evaluation criteria set forth herein, or give the successful Offeror a competitive advantage.
4.5 Conflict of Interest
If an Offeror has any existing client relationship that involves the Houston County Board of Education, the Offeror must disclose each relationship.
4.6 Compliance with Laws
The Vendor will comply with all State and Federal laws, rules, and regulations.
4.7 Evidence of Insurance
a) The successful Vendor, at its expense, shall carry and maintain in full force at all times during the term of the contract resulting from this RFP the following insurance:
Coverage Limits of Liability
| Workmen’s Compensation |
| Statutory |
| General Liability/Property Damage |
| $500,000 each occurrence |
$1,000,000 aggregate
| Personal Injury |
| $500,000 each occurrence |
$1,000,000 aggregate
| Automobile Liability/Property Damage |
| $500,000 each occurrence |
| Bodily Injury |
| $500,000 each occurrence |
$1,000,000 aggregate
b) Prior to commencement of performance of this Agreement, Contractor shall furnish to HCBOE a certificate of liability insurance evidencing all required coverage in at least the limits required herein, naming the Houston County School District, its elected officials, agents, and employees as additional insured under the Comprehensive General Liability coverage, and providing that no policies may be cancelled without ten (10) days advance written notice to the Board. Such certificate shall be issued to: Houston County School District.
c) Said policies shall remain in full force and effect until the expiration of the terms of the contract or until completion of all duties to be performed hereunder by the Contractor, whichever shall occur later.
RFP NUMBER 22-0?
Attachment A
PROPOSAL CERTIFICATION
I certify that I have read and understand the terms and conditions herein except as stated below. I further state that I am and/or my company is capable, able to, and will provide the requested products and/or service described herein. I am the owner or agent of the company stated below and am authorized and empowered to contract. By my signature on this RFP, I/we guarantee and certify that all items included in my bid meet or exceed specifications.
I certify that this quotation is made without prior understanding, agreement, or connection with any corporation, firm or person submitting a quotation for the same materials, supplies, equipment, or services and is in all respects fair and without collusion or fraud. I understand collusive bidding is a violation of State and Federal Law and can result in fines, prison sentences, and civil damage awards. I agree to abide by all conditions of the quotation and certify that I am authorized to sign this quotation for the Vendor.
SUBMITTED BY_________________________________________ DATE _______________
TITLE____________________________________EMAIL: ____________________________
COMPANY NAME____________________________________________________________
ADDRESS________________________________CITY______________ST_____ZIP_______
TELEPHONE NUMBER_______________________FAX NUMBER_____________________
COMPANY WEBSITE _________________________
SIGNATURE _________________________________________________________________
Can payment be made via credit card? ______________________________________________
Credit card fee: ________________________________________________________________
Company Name:_______________________________________________________________
Company Address: ____________________________________________________________
Company Phone/ Fax #:__________________________________________________________
Attachment B Contractor Affidavit under O.C.G.A. § 13-10-91(b)(1)
By executing this affidavit, the undersigned contractor verifies its compliance with O.C.G.A. § 13-10-91, stating affirmatively that the individual, firm or corporation which is engaged in the physical performance of services on behalf of Houston County Board of Education has registered with, is authorized to use and uses the federal work authorization program commonly known as E-Verify, or any subsequent replacement program, in accordance with the applicable provisions and deadlines established in O.C.G.A. § 13-10-91. Furthermore, the undersigned contractor will continue to use the federal work authorization program throughout the contract period and the undersigned contractor will contract for the physical performance of services in satisfaction of such contract only with subcontractors who present an affidavit to the contractor with the information required by O.C.G.A. § 13-10-91(b). Contractor hereby attests that its federal work authorization user identification number and date of authorization are as follows:
Federal Work Authorization User Identification Number Date of Authorization
| _________________________________ | ______________________________________ | |
| Name of Contractor | Name of Project |
Name of Public Employer
I hereby declare under penalty of perjury that the foregoing is true and correct.
Executed on ______, ___, 20___ in ____________________(city), ______(state).
Signature of Authorized Officer or Agent
Printed Name and Title of Authorized Officer or Agent
SUBSCRIBED AND SWORN BEFORE ME
ON THIS THE ______ DAY OF ______________,20___.
NOTARY PUBLIC
My Commission Expires:
Attachment C
Certificate Regarding Debarment, Suspension, Ineligibility
The Houston County School District is a recipient of Federal monies. As such we require that participating vendors not be debarred, suspended, ineligible or excluded from doing business with the Federal government or any agency thereof.
The prospective participant certifies, by submission of the proposal, that neither it, nor its principals, is presently debarred, suspended, proposed for debarment, declared ineligible, or excluded from participation in this transaction by any Federal department or agency.
Organization Name
Name(s) and Title(s) of Authorized Representative(s)
Signature(s) Date
Attachment D
DISTRICT STANDARD CONTRACT
SAMPLE CONTRACT
CONTRACT
This writing shall constitute the entire agreement between the Houston County School District, and _(VENDOR)_________________________________.
AGREEMENT: The Houston County School District agrees to the services provided by (VENDOR)_as listed herein and as modified from time to time. This agreement supersedes any purchase order issued in the course of executing this agreement. (VENDOR)_ agrees to provide the services and equipment listed herein in accordance with the terms and conditions herein and certifies that such services and equipment is as proposed in Houston County School District RFP # 20-019 This agreement may be modified only by written agreement and not by course of performance. This agreement becomes effective on _____ or on the day it is signed by all parties, whichever is later and will continue as indicated below.
DEFINITIONS: The meanings of the words below as used herein are defined as follows.
A. "District” as used herein means the Houston County School District, a political sub-division of the State of Georgia.
B. “Vendor or Contractor” as used herein means the company that will be awarded the contract.
LAW: The laws of the State of Georgia shall prevail in all matters concerning this contract.
TERM: Code section 20-2-506 of the laws of the State of Georgia as of this date and as may be amended apply to this agreement. In addition to other requirements, the following are specifically enumerated.
A. This contract will terminate absolutely and without further obligation on the part of the School District at the close of each calendar year. Unless the Board votes to cancel or non-renew, the contract will automatically renew at the end of each calendar year for a successive calendar year. The total contract periods shall not exceed 26 months ending 09/30/2022, except as provided herein.
B. This contract may be extended for no more than 3 months immediately following the expiring contract year.
TERMINATION:
A. The Houston County School District may terminate this contract in accordance with O.C.G.A. 20-2-506.
B. The Houston County School District may terminate this contract for non-performance of Contractor in any material respect and at the close of each calendar year by giving not less than 60 days notice to contractor.
C. The Contractor may terminate this contract for non-performance of the District in any material respect or at the close of each calendar year by giving written notice to the District not less than 60 days prior to termination.
D. The Contractor and the Houston County School District may mutually agree to terminate this contract at any time.
E. Upon total termination of this contract due to any reason, the District shall only be liable for the cost of unpaid past service periods. This District will release all equipment provided by this contract.
F. This contract will terminate absolutely and immediately at such time as appropriated and otherwise unobligated funds are no longer available to satisfy the obligations of this contract.
G. In the event of termination at the end of any calendar year period, the District shall only be liable for the cost of unpaid past service periods.
PRICE:
To be completed after proposal evaluation.
TAXES:
A. The Contractor shall be responsible for all taxes and fees and shall pay all taxes and fees brought about by this agreement.
B. The District shall provide the Contractor with a Sales & Use Tax Exemption Form.
INDEMNITY: To the extent permitted by law:
A. The parties to this Agreement will indemnify, defend and hold each other harmless from all losses, damages, claims, suits and actions (including court costs and reasonable attorney's fees) ("claims") arising out of any breach of this Agreement except to the extent caused by the negligence or intentional acts or omissions of the other.
B. The District shall not be required to insure the equipment provided under this contract from loss.
C. The District shall not be responsible for loss or damage to equipment.
ASSIGNMENT:
A. The Contractor shall not sell, assign, or transfer this agreement without the written consent of the District.
| Houston County School District | Offeror_______________________ | ||
| __________________________ | ______________________________ | ||
| Name | Name | ||
| __________________________ | ______________________________ | ||
| Title | Title | ||
| __________________________ | ______________________________ | ||
| Signature | Signature | ||
| __________________________ | ______________________________ | ||
| Date | Date |
image1.jpeg
Other files
Show all 15
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
File details come from the government source that posted it. Updated .