2024.01.12 Specification_Addm 3.pdf

PDF 736 KB Posted

Attached to
KALAMAZOO RESA CTE CENTER - TECHNOLOGY BID PACKAGE
Solicitation number
RFP - KRES - 240000000536
Issued by
Kalamazoo County, Port Hope Village, Michigan

About this file

This document is an Addendum to the bid documents for the KALAMAZOO RESA CTE CENTER - TECHNOLOGY BID PACKAGE project. The project owner is the Kalamazoo Regional Educational Service Agency (KRESA) in Kalamazoo, Michigan. The project involves the installation of various low voltage systems for the new Career and Technical Education Center, including audio/video, cabling, clocks, access control, surveillance, network infrastructure, and paging. The bid due date has been extended to January 23, 2024. Key dates include a pre-bid meeting on December 5, 2023, final RFI and substitution requests due on January 16, 2024, and the KRESA Board meeting for contract approval on January 30, 2024. The contract will be awarded to the responsive, responsible bidder.

The bid is for a single prime contract. The project is tax-exempt, and the contractor is responsible for applicable sales/use tax. Bid security of 5% of the bid amount is required. The successful bidder must provide a 100% performance bond and a labor and material payment bond. Contractors must be properly licensed, and meet insurance and bonding requirements.

View the file

Other files

Show all 12

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

ADDENDUM NO. 3

P:\Kalamazoo\214175 KRESA Career & Technical Edu Campus\G) CA\G10 Bid Docs\Technology Bid Package\Addendum 3\2024.01.12 Addendum 3.docx

PROJECT: Career Connect Campus - Technology Bid Package

CLIENT: Kalamazoo Regional Educational Service Agency

ISSUE DATE: 1/12/2024

The following clarifications and changes shall be included in the Plans and Specifications for the above referenced project, as prepared by Wightman & Associates, Inc. dated November 29, 2023. This Addendum shall be deemed a part of the Contract Documents, and to the extent that the provisions of the other Contract Documents are in conflict herewith, this Addendum shall control.

**BID DUE DATE EXTENSION to January 23, 2024**

SPECIFICATIONS:

1. Reissued Section 00 11 13 – Advertisement for Bids

a. Revised 1.2.1. Bid Date: January 23, 2024.

2. Reissued Section 00 31 13 – Preliminary Schedules

a. Revised 1. b. through g.

b. 01/16/2024 – Final RFI & Substitution Requests due

c. 01/17/2024 – Final Addendum Issued (if necessary)

d. 01/23/2024 – Bids due @ 4:00 PM, KRESA Building

e. 01/25/2024 – Post-Bid Interviews, KRESA Building, Conference Room

f. 01/26/2024 – Bid Recommendation to Owner

g. 01/30/2024 – KRESA Board Meeting for Approval and Contract Award

3. Issued Section 08 71 00.01 – Door Hardware Sets (FOR REFERENCE ONLY)

DRAWINGS:

(Following drawings issued FOR REFERENCE ONLY to provide door numbers and reflected ceiling plans.)

A1.1A through A1.1F First Floor Area Plans A1.2A through A1.2F Second Floor Area Plans A3.1 Overall First Floor Reflected Ceiling Plan A3.2 Overall Second Floor Reflected Ceiling Plan A8.2 Door & Frame Type & Schedule

ATTACHMENTS:

RFIs and responses to date.

ADDENDUM NO. 3

P:\Kalamazoo\214175 KRESA Career & Technical Edu Campus\G) CA\G10 Bid Docs\Technology Bid Package\Addendum 3\2024.01.12 Addendum 3.docx

The bidder hereby acknowledges receipt of this Addendum and shall include a signed copy with their bid.

Company Date

Signature Title

Print or Type Name

Kalamazoo Regional Educational Service Agency Wightman Career Connect Campus - Technology Bid Package 1/12/2024 Project No. 214175 Addendum 3

ADVERTISEMENT FOR BIDS 00 11 13 - 1

DOCUMENT 00 11 13 - ADVERTISEMENT FOR BIDS

1.1 PROJECT INFORMATION

A. Notice to Bidders: Qualified bidders may submit bids for the project as described in this Document. Submit bids according to the Instructions to Bidders.

B. Project Identification: Career Connect Campus – Technology Bid Package

Project Location: Career Connect Campus 3500 Vanrick Drive

Kalamazoo, Michigan 49001

C. Owner: Kalamazoo Regional Educational Service Agency 1819 East Milham Road Portage, Michigan 49002

D. Architect: Wightman & Associates 433 East Ransom Street Kalamazoo, Michigan 49007 Web Site: www.gowightman.com

E. Project Description: All low voltage systems shown in the project documents including audio/video, cabling, clocks, electronic access control, electronic surveillance, infrastructure equipment, wireless access points, switches, patch cables and paging.

for the entire building of the new Career and Technical Education Center Project. Note:

Fire alarm system is by others and not included in this bid package.

F. Construction Contract: Bids will be received for the following Work:

1. General Contract Bids shall be received from one prime contractor for all work as outlined in the Specifications and Construction Drawings.

2. All applicable laws, ordinances, and the rules and regulations of all authorities having jurisdiction over the construction of the project shall apply to the project throughout.

3. Contractors shall note that the project is subject to the Common Construction Wage Act (effective July 1, 2015) for record-keeping, and all terms of this Act shall be followed in their entirety.

4. The contract form for the project will be AIA Document A101.

5. Contract will be made to the responsive, responsible bidder awarded by the

Owner.

6. Kalamazoo Regional Educational Service Agency is tax-exempt. Contractors are responsible for appropriate sales/use tax in accordance with the State of Michigan Department of Treasury.

http://www.gowightman.com/

ADVERTISEMENT FOR BIDS 00 11 13 - 2

1.2 BID SUBMITTAL AND OPENING

The Owner will receive sealed lump sum bids until the bid time and date at the location given below. Owner will consider bids prepared in compliance with the Instructions to Bidders issued by Owner, and delivered as follows:

1. Bid Date: January 23, 2024 (ADDM 3).

2. Bid Time: 4:00 p.m. Eastern Standard Time.

3. Location: Kalamazoo RESA

1819 East Milham Road Portage, MI 49001

B. Bids will thereafter be publicly opened and read aloud.

C. Bids shall be submitted on the forms provided with all blanks populated. Bid form and other documents required to be submitted with the bid shall be enclosed in a sealed envelope with the Bidder’s name, addressed to:

Kalamazoo Regional Educational Service Agency, Attention: Career Connect Center - Technology Bid Package.

1.3 BID SECURITY

A. Each bid must be accompanied by a Familial Disclosure and Iran Sanctions Act Compliance forms completed as provided by law.

B. Bid security shall be submitted with each bid in the amount of five (5) percent of the bid amount.

C. Bids received after the designated time for closing will be returned unopened.

D. No bids may be withdrawn for a period of 60 days after the opening of bids. The owner reserves the right to reject any and all bids and to waive informalities and irregularities.

1.4 PRE-BID MEETING

A. Pre-bid Meeting: See Document 002513 "Pre-bid Meetings."

B. Pre-bid Meeting: A pre-bid meeting for all bidders will be held virtually on Tuesday, December 5, 2023, at 3:30 p.m. Eastern Standard Time. Prospective prime bidders are requested to attend.

1. Bidders' Questions: The architect will provide responses at the Pre-bid Meeting to bidders' questions received up to two (2) business days prior to the meeting.

ADVERTISEMENT FOR BIDS 00 11 13 - 3

1.5 DOCUMENTS

A. Online Procurement and Contracting Documents: Obtain access after November 29, 2023, at 3:00 p.m. by contacting the following:

1. Dodge Lead Center: www.dodgeprojects.construction.com

2. Wightman Bidding Website: https://bids.gowightman.com/

B. Viewing Procurement and Contracting Documents: Examine after November 21, 2023, at the locations below:

1. Wightman & Associates, Inc., 433 East Ransom Street, Kalamazoo, MI 49007

1.6 TIME OF COMPLETION

A. Successful bidder shall begin the Work on receipt of the Notice to Proceed and shall complete the Work within the Contract Time.

1.7 BIDDER'S QUALIFICATIONS

A. Bidders must be properly licensed under the laws governing their respective trades and be able to obtain insurance and bonds required for the Work.

B. A 100% Performance Bond, and a separate Labor and Material Payment Bond, and Insurance in a form acceptable to the Owner will be required as part of each Bid.

C. Each bid proposal shall include all labor, material, and services necessary to complete the project in strict accordance with the contract documents as prepared and on file in the office of Wightman & Associates, Inc. The Owner reserves the right to reject any or all bids.

D. Each bidder is responsible for inspecting the project site and for reading and being thoroughly familiar with the Contract Documents and Specifications. Failure of omission of any Bidder to do any of the foregoing shall not relieve the Bidder from any obligation with respect to their bid.

1.8 NOTIFICATION

A. This Advertisement for Bids document is issued by order of the Kalamazoo Regional Educational Service Agency.

END OF DOCUMENT 00 11 13

http://www.dodgeprojects.construction.com/ https://bids.gowightman.com/

PRELIMINARY SCHEDULES 00 31 13 - 1

DOCUMENT 00 31 13 - PRELIMINARY SCHEDULES

1.1 PROJECT SCHEDULE

A. This Document, with its referenced attachments, is part of the Procurement and Contracting Requirements for the Project. They provide the Owner's information for the Bidders' convenience and are intended to supplement rather than serve in lieu of the Bidders' investigations. They are available for Bidders' convenience and information but do not affect Contract Time requirements. This Document and its attachments are not part of the Contract Documents.

B. Available Project information includes the following:

1. Bid Schedule

a. 12/05/2023 – Pre-Bid Meeting @ 3:30 PM, Virtual

b. 01/16/2024 – Final RFI & Substitution Requests due (ADDM 3)

c. 01/17/2024 – Final Addendum Issued (if necessary) (ADDM 3)

d. 01/23/2024 – Bids due @ 4:00 PM, KRESA Building (ADDM 3)

e. 01/25/2024 – Post-Bid Interviews, KRESA Building, Conference Room F

(ADDM 3)

f. 01/26/2024 – Bid Recommendation to Owner (ADDM 3)

g. 01/30/2024 – KRESA Board Meeting for Approval and Contract Award

(ADDM 3)

C. The project schedule, including design and construction milestones, is available for viewing following this Section. CSM Group’s schedule is provided for reference.

1. Technology contractor key dates are:

a. 03/2024 – Access Control Pre-Installation Meeting

b. 06/2024 – Network Operational

c. 09/2024 through 01/2025 – Equipment Installation

d. 10/2024 – Site Surveillance Camera Installation

e. 01/2025 – Flat Panel Installation

f. 02/2025 through 03/2025 – Owner Training

g. 02/18/2025 - Substantial Completion

h. 03/2025 – Warranty Commencement

D. Related Requirements:

1. Document 00 41 13 "Bid Form - Stipulated Sum (Single-Prime Contract)" for Contract Time.

END OF DOCUMENT 00 31 13

TECHNOLOGY BID PACKAGE (FOR REFERENCE ONLY) Wightman + KRESA - Kalamazoo CTE Center DLR Project No. 214175 Bulletin 18

DOOR HARDWARE SETS 087100.01 - 1

SECTION 087100.01- DOOR HARDWARE SETS

REV.1 – BULLETIN #13

REV.2 - BULLETIN #14

REV.3 – BULLETIN #18

SET # 1

2 ea. Cont. gear hinges SL-11HD-EPT CL SEL

2 ea. Cont. gear hinges SL-14HD-EPT CL SEL

2 ea. Power transfers EPT-10-CON 628 VD

1 ea. Exit device QEL-RX-LD-9847NL-OP-CON 630 VD

1 ea. Exit device QEL-RX-LD-9847EO-CON 630 VD

1 ea. Rim cylinder 34 626 SAR

2 ea. Pulls RM5202 x 12HD 630 ROC

2 ea. Pulls RM7927 x 12HD 630 ROC

2 ea. Closers 4040XP- EDA x 4040XP- 61 689 LCN

2 ea. Overhead stops 1000S 630 ABH

2 ea. Sweeps 200NA AL NGP

1 ea. Threshold 513 x 2/ RCE AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Meeting stile astragal By Alum. Door Mfr. ---- ----

1 ea. Power supply PS904 ---- VD

1 ea. Power supply PS902-2RS ---- VD

2 ea. Wiring harness CON (length as required in door) ---- VD

2 ea. Wiring harness CON-192 ---- VD

2 ea. Door position switches MS-2049F ---- DET

OPERATION:

• Doors remain locked at all times.

• Request to exit switches in exit devices signal door position switches of an authorized egress through door.

• Exit device latches retracted and held in dogged-open position for push/ pull operation by card reader software for events.

• Free manual egress from inside at all times.

SET # 2

2 ea. Power transfers EPT-10-CON 628 VD

2 ea. Exit devices QEL-LX-RX-LD-9847EO-CON 630 VD

2 ea. Pulls RM5202 x 12HD 630 ROC

2 ea. Pulls RM7927 x 12HD 630 ROC

2 ea. Overhead stops 1000S 630 ABH

1 ea. Dual-auto. door operator By Sect. 087113 Supplier ---- ----

1 ea. Touchless wall actuator By Sect. 087113 Supplier ---- ----

2 ea. Touchless jamb

DOOR HARDWARE SETS 087100.01 - 2

actuators By Sect. 087113 Supplier ---- ----

2 ea. Sweeps 200NA AL NGP

1 ea. Threshold 513 x 2/ RCE AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Meeting stile astragal By Alum. Door Mfr. ---- ----

1 ea. Power supply PS904 ---- VD

1 ea. Power supply PS902-2RS ---- VD

2 ea. Wiring harness CON (length as required in door) ---- VD

2 ea. Wiring harness CON-192 ---- VD

2 ea. Door position switches MS-2049F ---- DET

2 ea. Remote release switches TS18 ---- ALC

1 ea. Camera/ intercom By Div. 28 Security Contractor ---- ----

1 ea. Card reader By Div. 28 Security Contractor ---- ----

• Request to exit switches in exit devices signal door position switches of an authorized egress through either door leaf.

• Presentation of credentials at card reader or remote pushbutton activates retraction of exit device latches, allowing either door leaf to be pulled open, and turning power to outside actuator “ON” for use of automatic door operator.

• Power to exterior automatic door operator (“ADO”) actuator controlled by exit device latch monitor switch:

o When latches are retracted by presentation of credentials, remote pushbutton, or held retracted by software for events, power to exterior ADO actuator is “ON”, allowing operator to open both door leaves simultaneously when hand waved in front of actuator.

o When latches are extended/ door locked, power to exterior ADO actuator is

“OFF”; waving hand in front of actuator will not activate operator.

• Power to interior jamb-mounted ADO actuators always “ON”.

o When latches are extended/ doors locked, waving hand in front of either interior jamb-mounted actuator activates retraction of exit device latches on both door leaves, signaling operator to open both door leaves simultaneously.

o When doors close, latches extend/ doors relock.

o Waving hand in front of either interior jamb-mounted ADO actuator when exit device latches are retracted, operator opens both door leaves simultaneously.

DOOR HARDWARE SETS 087100.01 - 3

SET # 2.1

2 ea. Power transfers EPT-10-CON 628 VD

1 ea. Exit device QEL-LX-RX-LD-9847NL-OP-CON 630 VD

1 ea. Exit device QEL-LX-RX-LD-9847EO-CON 630 VD

2 ea. Pulls RM7927 x 12HD 630 ROC

1 ea. Rim cylinder 34 626 SAR

2 ea. Overhead stops 1000S 630 ABH

1 ea. Dual-auto. door operator By Sect. 087113 Supplier ---- ----

1 ea. Touchless wall actuator By Sect. 087113 Supplier ---- ----

2 ea. Touchless jamb actuators By Sect. 087113 Supplier ---- ----

2 ea. Sweeps 200NA AL NGP

1 ea. Threshold 513 x 2/ RCE AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Meeting stile astragal By Alum. Door Mfr. ---- ----

1 ea. Power supply PS902-2RS ---- VD

2 ea. Wiring harness CON (length as required in door) ---- VD

2 ea. Wiring harness CON-192 ---- VD

2 ea. Door position switches MS-2049F ---- DET

2 ea. Remote release switches TS18 ---- ALC

• Request to exit switches in exit devices signal door position switches of an authorized egress through either door leaf.

• Presentation of credentials at card reader or remote pushbutton activates retraction of exit device latches, allowing either door leaf to be pulled open, and turning power to outside actuator “ON” for use of automatic door operator.

• Power to exterior automatic door operator (“ADO”) actuator controlled by exit device latch monitor switch:

o When latches are retracted by presentation of credentials, remote pushbutton, or held retracted by software for events, power to exterior ADO actuator is “ON”, allowing operator to open both door leaves simultaneously when hand waved in front of actuator.

o When latches are extended/ door locked, power to exterior ADO actuator is

“OFF”; waving hand in front of actuator will not activate operator.

• Power to interior jamb-mounted ADO actuators always “ON”.

o When latches are extended/ doors locked, waving hand in front of either interior jamb-mounted actuator activates retraction of exit device latches on both door leaves, signaling operator to open both door leaves simultaneously.

o When doors close, latches extend/ doors relock.

o Waving hand in front of either interior jamb-mounted ADO actuator when exit

DOOR HARDWARE SETS 087100.01 - 4

SET # 3

2 ea. Power transfers EPT-10-CON 628 VD

1 ea. Exit device QEL-RX-LD-9847NL-OP-CON 630 VD

1 ea. Exit device QEL-RX-LD-9847EO-CON 630 VD

1 ea. Rim cylinder 34 626 SAR

2 ea. Pulls RM5202 x 12HD 630 ROC

2 ea. Pulls RM7927 x 12HD 630 ROC

2 ea. Closers 4040XP- EDA x 4040XP-61 689 LCN

2 ea. Overhead stops 1000S 630 ABH

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Meeting stile astragal By Alum. Door Mfr. ---- ----

1 ea. Power supply PS904 ---- VD

1 ea. Power supply PS902-2RS ---- VD

2 ea. Wiring harness CON (length as required in door) ---- VD

• Request to exit switches in exit devices signal door position switches of an authorized egress through door.

• Exit device latches retracted and held in dogged-open position for push/ pull operation

SET # 4

2 ea. Power transfers EPT-10-CON 628 VD

2 ea. Exit devices QEL-LX-RX- LD-9847EO-CON 630 VD

2 ea. Pulls RM5202 x 12HD 630 ROC

2 ea. Pulls RM7927 x 12HD 630 ROC

2 ea. Overhead stops 1000S 630 ABH

1 ea. Dual-auto. door operator By Sect. 087113 Supplier ---- ----

1 ea. Touchless wall actuator By Sect. 087113 Supplier ---- ----

2 ea. Touchless jamb actuators By Sect. 087113 Supplier ---- ----

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Meeting stile astragal By Alum. Door Mfr. ---- ----

1 ea. Power supply PS904 ---- VD

1 ea. Power supply PS902-2RS ---- VD

2 ea. Wiring harness CON (length as required in door) ---- VD

DOOR HARDWARE SETS 087100.01 - 5

2 ea. Remote release switches TS18 ---- ALC

• Request to exit switches in exit devices signal door position switches of an authorized egress through either door leaf.

• Presentation of credentials at card reader or remote pushbutton activates retraction of exit device latches, allowing either door leaf to be pulled open, and turning power to vestibule actuator “ON” for use of automatic door operator.

• Power to vestibule automatic door operator (“ADO”) actuator controlled by exit device latch monitor switch:

o When latch is retracted by presentation of credentials, remote pushbutton, or held retracted by software for events, power to vestibule ADO actuator is “ON”, allowing operator to open both door leaves simultaneously when hand waved in front of actuator.

o When latch is extended/ door locked, power to vestibule ADO actuator is “OFF”;

waving hand in front of actuator will not activate operator.

• Power to Lobby-side jamb-mounted ADO actuators always “ON”.

o When latches are extended/ doors locked, waving hand in front of either interior jamb-mounted actuator activates retraction of exit device latches on both door leaves, signaling operator to open both door leaves simultaneously.

o When doors close, latches extend/ doors relock.

o Waving hand in front of either interior jamb-mounted ADO actuator when exit

SET # 5

1 ea. Cont. gear hinge SL-11HD- EPT CL SEL

1 ea. Cont. gear hinge SL-24HD- EPT CL SEL

1 ea. Cont. gear hinge SL-11HD CL SEL

1 ea. Cont. gear hinge SL-24HD CL SEL

1 ea. Power transfer EPT-10 (RHRA leaf) 689 VD

1 ea. Flushbolt 555-24” (top) 626 ROC

1 ea. Flushbolt 555-12” (bottom) 626 ROC

1 ea. Exit device RX- QEL- 9975 NL x 990NL 626 VD

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-EDA x 4040XP-30/61 (install for

180- degree swing) 689 LCN

1 ea. Wall-mounted holders 477S (install at 2’ from top of door) 626 ROC

1 ea. Dustproof strike 570 626 ROC

1 ea. Threshold 513HD x M.O. AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

DOOR HARDWARE SETS 087100.01 - 6

1 set Weatherstripping 700NA AL NGP

1 ea. Meeting stile astragal By Door Mfr. ---- ----

1 ea. Latch guard PMLP-111 630 DON

1 ea. Drip cap 16A x M.O. AL NGP

2 ea. Door position switches MS-2049F ---- DET

1 ea. Card reader By Div. 28 Security Contractor ---- ----

1 ea. Power supply PS904 ---- VD

1 ea. Wiring harness CON (length as required in door) ---- VD

1 ea. Wiring harness CON-192 ---- VD

1 set Metal edge/ astragal By Door Mfr. (flat astragal on act. leaf ext.) ---- ----

1 pc. Gasketing 5060 (attach to flat astragal) CLR NGP

• Presentation of credentials at card reader activates retraction of latch on active leaf exit device and allows door to be pulled open. Exit device relatches/ locks upon door closing.

• Request to exit switch in exit device signals door position switch of an authorized egress through active door leaf.

• Door relocks/ latches upon closing.

• Free manual egress through active door leaf at all times.

SET # 6

1 ea. Cont. gear hinge SL-14HD-EPT CL SEL

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Overhead stop 1000S 630 ABH

1 ea. Closer 4040XP-T x ST-3182 (install pull-side) 689 LCN

1 ea. Drop plate 4040-18G 689 LCN

1 ea. Threshold 513HD x 2/RCE AL NGP

1 ea. Sweep 101V AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Weatherstripping 700NA AL NGP

1 ea. Drip cap 16A x M.O. AL NGP

2 ea. Door position switches MS-2049F ---- DET

1 ea. Card reader By Div. 28 Security Contractor ---- ----

1 ea. Master power supply By Div. 28 Security Contractor ---- ----

• Door remains locked at all times.

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

• Strike remains locked in the event of power failure.

• Free manual egress from push-side at all times.

DOOR HARDWARE SETS 087100.01 - 7

SET # 6.1

1 ea. Cont. gear hinge SL-14HD-EPT CL SEL

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T 689 LCN

1 ea. Wall stop 400 626 ROC

1 ea. Threshold 513HD x 2/RCE AL NGP

1 ea. Sweep 101V AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Weatherstripping 700NA AL NGP

1 ea. Drip cap 16A x M.O. AL NGP

2 ea. Door position switches MS-2049F ---- DET

1 ea. Card reader By Div. 28 Security Contractor ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

• Free manual egress from push-side at all times.

SET # 7

1 ea. Cont. gear hinge SL-11HD- ATW CL SEL

1 ea. Cont. gear hinge SL-14HD- ATW CL SEL

1 ea. Exit device RX-LD-98NL -990NL-CON 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Electric strike 9600- 12/24VDC x 2005M3 630 HES

1 ea. Closer 4040XP- S-CUSH x 4040XP-30/ 61 689 LCN

1 ea. Threshold 513 x M.O. AL NGP

1 ea. Sweep 200NA AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 ea. Drip cap 16A x M.O. AL NGP

1 ea. Door position switch MS-2049F ---- DET

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Exit device relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 8

• Request to exit switch in exit device signals door position switch of an authorized egress through door.

SET # 8

1 ea. Cont. gear hinge SL-24HD- ATW CL SEL

1 ea. Exit device RX-LD-98NL -990NL-CON 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Electric strike 9600- 12/24VDC x 2005M3 630 HES

1 ea. Closer 4040XP- S-H-CUSH x 4040XP-30/ 61 689 LCN

1 ea. Armor plate 34” x 2LDW 630 ROC

1 ea. Threshold 513 x M.O. AL NGP

1 ea. Sweep 200NA AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Weatherstripping 700NA AL NGP

1 ea. Drip cap 16A x M.O. AL NGP

1 ea. Door position switch MS-2049F ---- DET

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Exit device relatches/ locks upon door closing.

• Request to exit switch in exit device signals door position switch of an authorized egress through door.

SET # 9

2 ea. Power transfers EPT-10-CON 628 VD

1 ea. Exit device QEL-RX-LD-9847NL-OP-CON 630 VD

1 ea. Exit device QEL-RX-LD-9847EO-CON 630 VD

1 ea. Rim cylinder 34 626 SAR

2 ea. Pulls RM5202 x 12HD 630 ROC

2 ea. Pulls RM7927 x 12HD 630 ROC

2 ea. Closers 4040XP-EDA x 4040XP- 61 689 LCN

2 ea. Overhead stops/ holders 1000H 630 ABH

DOOR HARDWARE SETS 087100.01 - 9

1 ea. Threshold 513 x 2/ RCE AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Meeting stile astragal By Alum. Door Mfr. ---- ----

1 ea. Power supply PS904 ---- VD

1 ea. Power supply PS902-2RS ---- VD

2 ea. Wiring harness CON (length as required in door) ---- VD

• Request to exit switches in exit devices signal door position switches of an authorized egress through door.

• Presentation of credentials at card reader activates retraction of exit device latch at RHR leaf only, allowing door leaf to be pulled open. Door relocks/ latches when closed.

• Exit device latches retracted and held in dogged-open position for push/ pull operation

SET # 10

2 ea. Power transfers EPT-10-CON 628 VD

2 ea. Exit devices QEL-LX-RX-LD-9847EO-CON 630 VD

2 ea. Pulls RM5202 x 12HD 630 ROC

2 ea. Pulls RM7927 x 12HD 630 ROC

2 ea. Overhead stops 1000S 630 ABH

1 ea. Dual-auto. door operator By Sect. 087113 Supplier ---- ----

1 ea. Touchless wall actuator By Sect. 087113 Supplier ---- ----

2 ea. Touchless jamb actuators By Sect. 087113 Supplier ---- ----

1 ea. Custom bollard By Sect. 087113 Supplier ---- ----

2 ea. Sweeps 200NA AL NGP

1 ea. Threshold 513 x 2/ RCE AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 set Meeting stile astragal By Alum. Door Mfr. ---- ----

1 ea. Power supply PS904 ---- VD

1 ea. Power supply PS902-2RS ---- VD

2 ea. Wiring harness CON (length as required in door) ---- VD

2 ea. Wiring harness CON-192 ---- VD

2 ea. Door position switches MS-2049F ---- DET

2 ea. Remote release switches TS18 ---- ALC

DOOR HARDWARE SETS 087100.01 - 10

• Request to exit switches in exit devices signal door position switches of an authorized egress through either door leaf.

• Presentation of credentials at card reader or remote pushbutton activates retraction of exit device latches, allowing either door leaf to be pulled open, and turning power to outside actuator “ON” for use of automatic door operator.

• Power to exterior automatic door operator (“ADO”) actuator controlled by exit device latch monitor switch:

o When latches are retracted by presentation of credentials, remote pushbutton, or held retracted by software for events, power to exterior ADO actuator is “ON”, allowing operator to open both door leaves simultaneously when hand waved in front of actuator.

o When latches are extended/ door locked, power to exterior ADO actuator is

“OFF”; waving hand in front of actuator will not activate operator.

• Power to interior jamb-mounted ADO actuators always “ON”.

o When latches are extended/ doors locked, waving hand in front of either interior jamb-mounted actuator activates retraction of exit device latches on both door leaves, signaling operator to open both door leaves simultaneously.

o When doors close, latches extend/ doors relock.

o Waving hand in front of either interior jamb-mounted ADO actuator when exit

DOOR HARDWARE SETS 087100.01 - 11

SET # 11

1 ea. Cont. gear hinge SL-14HD- ATW CL SEL

1 ea. Institution lockset L9082L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Electric strike 8500L x LBSM x 2005M3 630 HES

1 ea. Overhead stop 1000S 630 ABH

1 ea. Closer 4040XP- S-CUSH x 4040XP-30/ 61 689 LCN

1 ea. Closer 4040XP-T x ST-3182 x 4040SP-18G 689 LCN

1 ea. Threshold 513 x 2/RCE AL NGP

1 ea. Sweep 200NA AL NGP

1 set Weatherstripping By Alum. Frame Mfr. ---- ----

1 ea. Drip cap 16A x D.O. +4” AL NGP

1 ea. Door position switch MS-2049F ---- DET

2 ea. Card readers By Div. 28 Security Contractor ---- ----

• Presentation of credentials at either card reader releases electric strike and allows door to be pushed/ pulled open. Lockset relatches/ locks upon door closing.

• Request to exit switch in exit device signals door position switch of an authorized egress through door.

SET # 12

2 ea. Power transfers EPT-10-CON 628 VD

1 ea. Exit device QEL-LX-LD-9847NL-OP-LB-CON 630 VD

1 ea. Exit device QEL-LX-LD-9847EO-LB-CON 630 VD

2 ea. Pulls RM5202 x 12HD 630 ROC

2 ea. Pulls RM7927 x 12HD 630 ROC

1 ea. Rim cylinder 34 626 SAR

2 ea. Overhead stops 1000S 630 ABH

1 ea. Dual-auto. door operator By Sect. 087113 Supplier ---- ----

1 ea. Touchless wall actuator By Sect. 087113 Supplier ---- ----

2 ea. Touchless jamb actuators By Sect. 087113 Supplier ---- ----

1 ea. Power supply PS904 ---- VD

1 ea. Power supply PS902-2RS ---- VD

2 ea. Wiring harness CON (length as required in door) ---- VD

DOOR HARDWARE SETS 087100.01 - 12

• Both exit devices and operator are tied into the fire alarm system.

• Presentation of credentials at card reader activates retraction of both exit device latches, allowing either door leaf to be pulled open, and turning power to Corridor actuator “ON” for use of automatic door operator.

• Power to Corridor automatic door operator (“ADO”) actuator controlled by exit device latch monitor switch:

o When latch is retracted by presentation of credentials or held retracted by software for events, power to Corridor ADO actuator is “ON”, allowing operator to open both door leaves simultaneously when hand waved in front of actuator.

o When latch is extended/ door locked, power to Corridor ADO actuator is “OFF”;

waving hand in front of actuator will not activate operator.

• Power to Conference Room-side jamb-mounted ADO actuators always “ON”.

o When latches are extended/ doors locked, waving hand in front of either interior jamb-mounted actuator activates retraction of exit device latches on both door leaves, signaling operator to open both door leaves simultaneously.

o When doors close, latches extend/ doors relock.

o Waving hand in front of either interior jamb-mounted ADO actuator when exit device latches are retracted, operator opens both door leaves simultaneously.

• Both exit device latches retracted and held in dogged-open position for push/ pull operation by card reader software for events.

o Activation of fire alarm system or power failure releases latch on both door leaves to latch/ relock.

• Automatic operator to tie into fire alarm system.

o When programmed through software for events, operator holds both doors open.

o Activation of fire alarm system or power failure releases both door leaves to close and latch/ lock.

SET # 13

1 ea. Cont. gear hinges SL-14HD-EPT CL SEL

1 ea. Cont. gear hinges SL-14HD CL SEL

1 ea. Power transfer EPT-10-CON 628 VD

1 ea. Exit device QEL-LD-9847NL-OP-LBR-CON 630 VD

1 ea. Exit device LD-9847EO-LBR 630 VD

1 ea. Rim cylinder 34 626 SAR

2 ea. Pulls RM5202 x 12HD 630 ROC

2 ea. Pulls RM7927 x 12HD 630 ROC

2 ea. Closers 4040XP-SE x 120VAC 689 LCN

2 ea. Overhead stops 1000S 630 ABH

1 ea. Power supply PS904 ---- VD

1 ea. Power supply PS902-2RS ---- VD

1 ea. Wiring harness CON (length as required in door) ---- VD

1 ea. Wiring harness CON-192 ---- VD

DOOR HARDWARE SETS 087100.01 - 13

• Presentation of credentials at card reader activates retraction of exit device latch at RHR leaf, allowing door leaf to be pulled open. Door relocks/ latches when closed.

• Exit device latch on RHR leaf retracted and held in dogged-open position for push/ pull operation by card reader software for events.

• Electronic hold-open closers to tie into fire alarm system.

o Activation of fire alarm system or power failure releases both door leaves to close and latch/ lock.

SET # 14

1 ea. Cont. gear hinge SL-24HD- ATW CL SEL

1 ea. Exit device RX-98NL-F -990NL-CON 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Electric strike 9600- 12/24VDC x 2005M3 630 HES

1 ea. Closer 4040XP- S-CUSH x 4040-30 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Threshold 513 x M.O. AL NGP

1 ea. Sweep 200NA AL NGP

1 set Weatherstripping 700NA AL NGP

1 ea. Drip cap 16A x M.O. AL NGP

1 ea. Door position switch MS-2049F ---- DET

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Exit device relatches/ locks upon door closing.

• Request to exit switch in exit device signals door position switch of an authorized egress through door.

SETS # 15-18 NOT USED

DOOR HARDWARE SETS 087100.01 - 14

SET # 19

1 ea. Cont. gear hinge SL-24HD CL SEL

1 ea. Office lockset L9050L- LATA x 09-509 x 583-363* 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Overhead holder 1000H 630 ABH

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing 5060 CL NGP

*Prep frame for future electric strike.

SET # 20

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T (pull-side) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 400 626 ROC

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 15

SET # 20.1

3 ea. Butt hinges BB1168- 4.5 x 4.5 652 HAG

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-EDA (x 4040XP-61 at alum. frames) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing By Alum. Frame Mfr. ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 20.2

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T (pull- side) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Armor plate 34” x 2LDW (pull-side) 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 16

Set # 21

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- CUSH (x 4040XP-30/61 at aluminum frames) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

Set # 21.1

1 ea. Office lockset L9050L- LATA x 09-509 x 583-363 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- S-CUSH (x 4040XP-30/61 at aluminum frames) 689 LCN

1 ea. Kick plate 8” x 2LDW 630 ROC

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 17

SET # 22

3 ea. Butt hinges BB1279- 4.5 x 4.5 652 HAG

1 ea. Mortise cylinder 41 626 SAR

1 ea. Wall stop 400 626 ROC

SET # 22.1

1 ea. Mortise cylinder 41 626 SAR

1 ea. Overhead stop 9000S x 90541 630 ABH

SET # 22.2

1 ea. Mortise cylinder 41 626 SAR

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop/ holder 494S 626 ROC

SET # 22.3

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T (pull-side) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 400 626 ROC

DOOR HARDWARE SETS 087100.01 - 18

SET # 22.4

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T (pull-side) 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

SET # 22.5

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-CUSH 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

SET # 23

1 ea. Classroom lockset L9070L- LATA* 626 SCH

1 ea. Wall stop 400 626 ROC

SET # 24

1 ea. Institutional lockset L9082L- LATA 626 SCH

2 ea. Mortise cylinders 41 626 SAR

1 ea. Closer 4040XP-EDA 689 LCN

1 ea. Kick plate 10” x 34” 630 LCN

1 ea. Wall stop 400 626 ROC

1 set Gasketing 5060 CL NGP

DOOR HARDWARE SETS 087100.01 - 19

• Door remains locked both sides at all times.

• Presentation of credentials at either card reader releases electric strike and allows door to be pushed/ pulled open. Lockset relatches/ locks upon door closing.

• When programmed through card reader software, electric strike to remain unlocked during normal workdays.

SET # 24.1

1 ea. Institutional lockset L9082L- LATA 626 SCH

2 ea. Mortise cylinders 41 626 SAR

1 ea. Closer 4040XP-EDA 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing 5060 CL NGP

1 set Soundseal 700NA AL NGP

1 ea. Dropseal 423N AL NGP

• Presentation of credentials at either card reader releases electric strike and allows door to be pushed/ pulled open. Lockset relatches/ locks upon door closing.

SET # 24.2

1 ea. Institutional lockset L9082L- LATA 626 SCH

2 ea. Mortise cylinders 41 626 SAR

1 ea. Closer 4040XP-S-CUSH 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at either card reader releases electric strike and allows door

DOOR HARDWARE SETS 087100.01 - 20

SET # 24.3

1 ea. Institutional lockset L9082L- LATA 626 SCH

2 ea. Mortise cylinders 41 626 SAR

1 ea. Closer 4040XP- T x ST-3182 x 4040-18G (pull-side) 689 LCN

1 ea. Overhead stop 1000S 630 ABH

1 ea. Kick plate 10”” x 2LDW 630 ROC

1 set Gasketing 5060 CL NGP

• Door remains locked b

• oth sides at all times.

• Presentation of credentials at either card reader releases electric strike and allows door

SET # 25

1 ea. Passage set L9010L- LATA* 626 SCH

1 ea. Wall stop 400 626 ROC

SET # 26

1 ea. Privacy lockset L9040- LATA x ADA TT x Vacant/ occupied* 626 SCH

1 ea. Closer 4040XP-T (pull-side) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 400 626 ROC

SET # 26.1

1 ea. Electric strike 1006DB-2 x 2005M3 630 HES

1 ea. Hotel lockset L9486L- LATA x L583-375 x 09-509 x

L583-363 626 SCH

1 ea. Hotel mortise cylinder 41-115 626 SAR

DOOR HARDWARE SETS 087100.01 - 21

1 ea. Emergency key 7268EMX ---- SAR

1 ea. Closer 4040XP-T (pull-side) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 487 626 ROC

1 set Gasketing 5060 CL NGP

• Outside indicator shows “unoccupied”.

• Presentation of credentials at card reader releases electric strike and allows door to be pushed open. Lockset relatches/ locks upon door

• closing.

• Turning inside thumbturn throws deadbolt and locks out use of credentials at card reader; outside indicator shows “occupied”.

• Turning inside lever retracts both deadbolt and latchbolt, allowing door to be pulled open, and changing indicator from “occupied” to “unoccupied”.

• Strike remains locked in the event of power failure.

• Free manual egress from inside at all times.

• Strike remains locked in the event of power failure.

• Only the emergency key (NOT master key) can unlock deadbolt from outside in the event of an emergency.

SET # 27

1 ea. Electric strike 9500 x 2005M3 630 HES

1 ea. Exit device 98L-NL-F x LATA 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Closer 4040XP-T (pull-side) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing 5060 CL NGP

1 ea. Drop seal 420NA AL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Exit device relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 22

SET # 28

1 ea. Exit device 98BE-F x LATA 630 VD

1 ea. Closer 4040XP-T (pull-side) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 400 626 ROC

1 ea. Wall-mounted magnet 996M x 120VAC* 689 RIX

*Electromagnetic door holder to tie into fire alarm system; activation of fire alarm system or power failure releases door to close and latch.

SET # 29

1 ea. Exit device 98EO-F* 630 VD

1 ea. Closer 4040XP- CUSH 689 LCN

1 ea. Armor plate 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

SET # 30

1 ea. Electric strike 9600 x 2005M3 630 HES

1 ea. Exit device LD-98L-NL x LATA 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Closer 4040XP-EDA (x 4040XP-61 at alum. frames)

Install for 180-degree swing where applicable 689 LCN

1 ea. Armor plate 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 23

SET # 30.1

1 ea. Cont. gear hinge SL-11HD CL SEL

1 ea. Cont. gear hinge SL-14HD CL SEL

1 ea. Electric strike 9600 x 2005M3 630 HES

1 ea. Exit device LD-98L-NL x LATA 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Closer 4040XP-EDA (x 4040XP-61 at alum. frames)

Install for 180-degree swing where applicable 689 LCN

1 ea. Wall stop 400 626 ROC

1 set Gasketing By Alum. Frame Mfr. ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 31

1 ea. Electric strike 9500 x 2005M3 630 HES

1 ea. Electric strike 9600 x 2005M3 630 HES

1 ea. Exit device LD-98L-NL x LATA 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Closer 4040XP-CUSH (x 4040XP-30/61 at aluminum frames) 689 LCN

1 set Gasketing By Alum. Frame Mfr. ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 24

SET # 31.1

1 ea. Electric strike 9600 x 2005M3 630 HES

1 ea. Exit device LD-98L-NL x LATA 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Closer 4040XP-S-CUSH (x 4040XP-30/61 at aluminum frames) 689 LCN

1 set Gasketing By Alum. Frame Mfr. ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 32

1 ea. Exit device LD- 98L-NL x LATA 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Closer 4040XP-CUSH 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Exit device relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 25

SET # 33

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- CUSH (x 4040XP-30/ 61 at aluminum frames) 689 LCN

1 ea. Armor plate 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing By Alum. Frame Mfr. ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 33.1

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-EDA 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Soundseal 700N AL NGP

1 ea. Dropseal 423N AL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 26

SET # 33.2

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- CUSH x 4040XP-30 689 LCN

1 ea. Armor plate 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing By Alum. Frame Mfr. ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 34

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- S-CUSH (x 4040XP-30/61 at aluminum frames) 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 27

SET # 35

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- T (install pull-side) 689 LCN

1 ea. Kick plate 10” x 2LDW (push-side) 630 ROC

1 ea. Armor plate 34” x 2LDW (pull-side) 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 36

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- EDA x 4040XP-61 689 LCN

1 ea. Wall stop 400 626 ROC

1 set Gasketing By Alum. Frame Mfr. ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 28

SET # 37

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Overhead stop 1000S 630 ABH

1 ea. Closer 4040XP- T x ST-3182 689 LCN

1 set Gasketing By Alum. Frame Mfr. ---- ----

1 ea. Drop plate 4040XP-18G 689 LCN

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

a.) Door E212: change hinge to SL-24HD in lieu of SL-11HD

SET # 38

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Overhead stop 1000S 630 ABH

1 ea. Closer 4040XP- T x ST-3182 689 LCN

1 ea. Drop plate 4040XP-18G 689 LCN

1 set Gasketing By Alum. Frame Mfr. ---- ----

1 ea. Remote release switch TS18 ---- ALC

• Presentation of credentials at card reader or pressing remote release switch releases electric strike and allows door to be pushed open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 29

SET # 38.1

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-EDA (x 4040XP-61 at alum. frames) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing By Alum. Frame Mfr. ---- ----

1 ea. Remote release switch TS18 ---- ALC

1 ea. Camera/ intercom By Div. 28 Security Contractor ---- ----

• Presentation of credentials at card reader or remote release button at reception desk releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 39

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Overhead stop 1000S 630 ABH

2 ea. Kick plates 8” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 30

SET # 40

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- EDA (install for 180-degree swing where applicable) 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 41

1 ea. Exit device 98L-NL-F x LATA 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Closer 4040XP-EDA 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Exit device relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 31

SET # 42

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T (pull-side) 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop 400 626 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 43

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T (pull-side x 180-degree) 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Magnetic holder 996M x 120VAC 689 RIX

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

• Strike remains locked in the event of power failure.

• Free manual egress from inside at all times.

• Electromagnetic holder holds door open. Activation of the fire alarm system or power failure releases door to swing closed and latch.

DOOR HARDWARE SETS 087100.01 - 32

SET # 43.1

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- T (top-jamb mount x pull-side; install for 180-degree swing) 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing 5060 CL NGP

1 ea. Magnetic holder 996M x 120VAC 689 RIX

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

• Strike remains locked in the event of power failure.

• Free manual egress from inside at all times.

• Electromagnetic holder holds door open. Activation of the fire alarm system or power failure releases door to swing closed and latch.

SET # 44

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- S-CUSH 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

a.) Door E100L: delete spring from cushion arm; provide standard “CUSH” arm

DOOR HARDWARE SETS 087100.01 - 33

SET # 45

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP- T (pull-side) 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 ea. Wall stop/ holder 477 626 ROC

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 46

1 ea. Exit device 98L-NL-F x LATA 630 VD

1 ea. Rim cylinder 34 626 SAR

1 ea. Closer 4040XP-S-CUSH 689 LCN

2 ea. Armor plates 34” x 2LDW 630 ROC

1 ea. Door edge 305- 34” 630 ROC

1 set Gasketing 5060 CL NGP

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Exit device relatches/ locks upon door closing.

DOOR HARDWARE SETS 087100.01 - 34

SET # 47

1 set Bifold door hardware 9890- 36” ---- HAG

1 ea. Pull knob 841 x SNB 626 HAG

SET # 48

1 ea. Mortise cylinder 41/ 42 As required 626 SA

Balance of all other hardware by Coiling Door manufacturer.

SET # 49

1 ea. Mortise cylinder 41/ 42 As required 626 SA

Balance of all other hardware by Sectional Door manufacturer.

SET # 50

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T (pull-side) 689 LCN

1 ea. Wall stop 400 626 ROC

1 set Gasketing By Alum. Frame Mfr. ---- ----

• Presentation of credentials at card reader releases electric strike and allows door to be pulled open. Lockset relatches/ locks upon door closing.

SET # 51

1 ea. Electric strike 8500L x 2005M3 630 HES

1 ea. Storeroom lockset L9080L- LATA 626 SCH

1 ea. Mortise cylinder 41 626 SAR

1 ea. Closer 4040XP-T (pull-side) 689 LCN

1 ea. Kick plate 10” x 2LDW 630 ROC

1 ea. Wall stop 400 626 ROC

DOOR HARDWARE SETS 087100.01 - 35

1 set Gasketing By Alum. Frame Mfr.

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .