15_Silencer-Drawing_Stbd_8in-ANSI150_2022-10-12.pdf

PDF 150 KB Posted

Attached to
ADF&G Request for Information (RFI) - RV Medeia Repower
Solicitation number
Not on record
Issued by
Alaska

About this file

This is a technical drawing document for a silencer product manufactured by Maxim Silencers. The document specifies a Super Critical Grade 8 silencer model M42-8C2-16582, revision 00, dated October 11, 2022. The silencer is designed as an 8-inch flange unit drilled to ANSI #150 specifications for both inlet and outlet connections, with dimensions measuring 79 inches in nominal diameter and weighing 318 pounds. The equipment features a 1/2-inch FNPT drain and is constructed entirely from welded carbon steel with black paint external finish. The drawing indicates standard Maxim construction tolerances of 1/4 inch and notes that the silencer is designed to support its own weight only. All dimensions are provided in inches unless otherwise specified, with critical dimensions subject to specified tolerances.

The document serves as proprietary technical specification material belonging to Maxim Silencers, with explicit prohibition against transmittal to unauthorized parties or use outside the intended purpose. The drawing was prepared by JC and checked by WS on October 11, 2022, with approval from SALES on the same date. Contact information is provided as (713) 682-6777 and info@maximsilencers.com. The document notes that drawings are subject to change without notice and explicitly states "Do not scale drawing," emphasizing the importance of using the specified dimensions for manufacturing and procurement purposes.

View the file

Other files

File Type Posted
21_Photo_2019-01_Port-Main-Replacement_Deck-Opening-Cut-Above-ER.jpg JPG image
27_Photo_Prior-Deck-Opening_Exhaust-Manifold-Lowered-Through-Deck.jpg JPG image
33_Photo_2026-07_Port-Gear-Nameplate_Twin-Disc-MG530_Full.jpg JPG image
Attachment 2 - Stablility Booklet.pdf PDF
47_Photo_2026-07_Machinery-Data-Card_Handwritten.jpg JPG image
20_Deck-Crane_North-American-MCK-1240_Load-Chart.pdf PDF
39_Photo_2026-07_Stbd-Gear-Nameplate_Ratio-and-Serial.jpg JPG image
16_Maxim-Silencers_M42-Super-Critical_Data-Sheet.pdf PDF
01_EBDG-26075-062-0_Repower-Conceptual-Study_RevP0.pdf PDF
ADFG Request for Information (RFI) - RV Medeia Repower.pdf PDF
38_Photo_2026-07_Stbd-Gear-Nameplate_Model-and-BOM.jpg JPG image
25_Photo_Prior-Deck-Opening_Cut-Line-Layout.jpg JPG image
23_Photo_2019-01_Port-Main-Replacement_ER-Through-Opening-After-Removal.jpg JPG image
29_Photo_2026-07_ER-Main-Engine_Gear-End-and-Exhaust-Lagging.jpg JPG image
32_Photo_2026-07_ER-Marine-Gear-Top-with-Exhaust-Risers-Above.jpg JPG image
Attachment 1 - Cost Schedule.pdf PDF
45_Photo_2026-07_ER-Looking-Aft_Mains-and-Exhaust-Risers-1.jpg JPG image
28_Photo_2026-07_ER-Overview_Between-Mains-Looking-Along-Centerline.jpg JPG image
40_Photo_2026-07_ER-Main-Engine_Exhaust-Risers-and-Cooling-Piping.jpg JPG image
42_Photo_2026-07_ZF-MicroCommander-Control-Processor_Stbd.jpg JPG image
02_EBDG-26075-256-2_FW-Cooling-System-Mods_RevP1-Preliminary.pdf PDF
11_Dwg-C2412-1_Hydrostatic-Curves-of-Form.pdf PDF
43_Photo_2026-07_ZF-MicroCommander-Control-Processor_Port.jpg JPG image
10_Dwg-U193-3_Lines-Plan.pdf PDF
09_Dwg-S2-192_Small-Vessel-Transverse-Frames.pdf PDF
19_Port-Main_Engine-Run-In-Report_Pacific-Power-Group_2018-11.pdf PDF
08_Dwg-U184-56_Transverse-Frames-and-Longitudinal-Section.pdf PDF
30_Photo_2026-07_ER-Main-Engine_Outboard-Side-and-Piping.jpg JPG image
12_Dwg-C2412-2_Cross-Curves.pdf PDF
18_Detroit-Diesel_Exhaust-System-Data_16V-92N-Highlighted.pdf PDF
05_Dwg-U192-S1_General-Scantling.pdf PDF
06_Dwg-U192-S4_Transverse-Frames.pdf PDF
04_Dwg-U192-MI_Shafting-Installation.pdf PDF
41_Photo_2026-07_ER-Main-Engine_Exhaust-Risers-and-Air-Cleaner.jpg JPG image
46_Photo_2026-07_ER-Looking-Aft_Mains-and-Exhaust-Risers-2.jpg JPG image
17_Detroit-Diesel_16V-92_Engine-Performance-Curve_E4-8162-12-6.pdf PDF
37_Photo_2026-07_Port-Main_Block-Casting-Number-Closeup.jpg JPG image
24_Photo_2019-01_Port-Main-Replacement_Old-Engine-and-Gear-on-Deck.jpg JPG image
35_Photo_2026-07_Port-Gear-Nameplate_Ratio-and-Serial.jpg JPG image
44_Photo_2026-07_Port-Exhaust-Elbow_Material-ID-Tag.jpg JPG image
14_Silencer-Drawing_Port_8in-ANSI150_2022-10-12.pdf PDF
03_Duramax_SC-424PFDP_Keel-Cooler-Installation-Drawing.pdf PDF
26_Photo_Prior-Deck-Opening_Opening-From-Above.jpg JPG image
07_Dwg-U192-S5_Transverse-Frames.pdf PDF
31_Photo_2026-07_ER-Marine-Gear-and-Foundation.jpg JPG image
22_Photo_2019-01_Port-Main-Replacement_Old-Engine-Visible-Through-Opening.jpg JPG image
34_Photo_2026-07_Port-Gear-Nameplate_Model-and-BOM.jpg JPG image
36_Photo_2026-07_Port-Main_Block-Casting-Number.jpg JPG image
Show all 48

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

TYPE:

MODEL NO.: REV:

SHEET:

DRAWING TYPE:

DATE:DRAWN BY:

CHECKED BY: DATE:

EST. WEIGHT:

ALL DIMENSIONS IN INCHES UNLESS

OTHERWISE SPECIFIED.

TOLERANCES APPLY ON CRITICAL

DIMENSION(S) AS SHOWN BELOW:

1/4" IMP FRAC; 0.25 IMP DEC

6.35 MM METRIC; 2 ANGULAR

HOLD - CRITICAL DIMENSION

THE INFORMATION HEREIN IS THE PROPERTY

OF MAXIM SILENCERS. TRANSMITTAL TO

OTHERS OR USE EXCEPT THAT FOR WHICH

IT IS PROVIDED IS STRICTLY PROHIBITED.

DO NOT SCALE DRAWING.

THIRD ANGLE

PROJECTION

DIM

EXTERNAL FINISH:

APPROVED BY: DATE:

PH: (713) 682-6777

WWW.MAXIMSILENCERS.COM

INFO MAXIMSILENCERS.COM@

79" NOM DIA

"26

10"

8-5/8"

17"

8-5/8"

17"

HEAD

"26

8-5/8"

5"

REF

"13-1/2 "8-13/16

" TYP.7/8 "11-3/4

"13-1/2 "8-13/16

" TYP.7/8 "11-3/4

XX XX MM/DD/YY XXXXXXXXXXXXXXX

REV. NO. REV. BY DATE DESCRIPTION

SILENCER SUPER CRITICAL GRADE

8 M42 C SI

M42-8C2-16582 00

JC 10/11/22

318 LBS 1 OF 1HT BLACK PAINT

NOTES:

1. MATERIAL CARBON STEEL .

2. SILENCER IS DESIGNED TO SUPPORT OWN WEIGHT ONLY.

3. STANDARD MAXIM CONSTRUCTION TOLERANCE APPLY ( 1/4").

4. ALL WELDED CONSTRUCTION.

5. DRAWING SUBJECT TO CHANGE WITHOUT NOTICE.

SALES

TF 10/11/22

WS 10/11/22

OUTLET 8 IN FLANGE

DRILLED TO ANSI #150

INLET 8 IN FLANGE

DRILLED TO ANSI #150

VIEW FROM OUTLET END

1/2" FNPT

DRAIN

INLET OUTLET

VIEW FROM INLET END

Sheet 1
Views
new_view_1
right_2
new_view_3
new_view_5
new_view_6
left_7

File details come from the government source that posted it. Updated .