14_Silencer-Drawing_Port_8in-ANSI150_2022-10-12.pdf

PDF 155 KB Posted

Attached to
ADF&G Request for Information (RFI) - RV Medeia Repower
Solicitation number
Not on record
Issued by
Alaska

About this file

This is a technical drawing document for a silencer component manufactured by Maxim Silencers. The drawing specifies a Super Critical Grade silencer model M42-8C2-16583, revision 00, dated October 11, 2022. The silencer features an 8-inch outlet flange and an 8-inch inlet flange, both drilled to ANSI #150 specifications, with a nominal diameter of 76 inches and a total height of 26 inches. The unit weighs approximately 318 pounds and is constructed from carbon steel with all welded construction and black paint external finish. Key specifications indicate the silencer is designed to support its own weight only, with standard Maxim construction tolerances of 1/4 inch, and includes a 1/2-inch female national pipe thread (FNPT) drain outlet.

The drawing includes standard engineering notations, dimensioning in inches, and third-angle projection views. Tolerances are specified for critical dimensions with fractional imprecial at 1/4 inch, decimal imperial at 0.25 inch, and metric at 6.35 millimeters, with angular tolerances held at critical dimensions. The document is proprietary to Maxim Silencers, with contact information provided at (713) 682-6777 and www.maximsilencers.com, and is subject to change without notice. This technical drawing would be used for procurement, manufacturing reference, or specification purposes related to silencer equipment acquisition or installation.

View the file

Other files

File Type Posted
21_Photo_2019-01_Port-Main-Replacement_Deck-Opening-Cut-Above-ER.jpg JPG image
27_Photo_Prior-Deck-Opening_Exhaust-Manifold-Lowered-Through-Deck.jpg JPG image
33_Photo_2026-07_Port-Gear-Nameplate_Twin-Disc-MG530_Full.jpg JPG image
Attachment 2 - Stablility Booklet.pdf PDF
47_Photo_2026-07_Machinery-Data-Card_Handwritten.jpg JPG image
20_Deck-Crane_North-American-MCK-1240_Load-Chart.pdf PDF
39_Photo_2026-07_Stbd-Gear-Nameplate_Ratio-and-Serial.jpg JPG image
16_Maxim-Silencers_M42-Super-Critical_Data-Sheet.pdf PDF
01_EBDG-26075-062-0_Repower-Conceptual-Study_RevP0.pdf PDF
ADFG Request for Information (RFI) - RV Medeia Repower.pdf PDF
38_Photo_2026-07_Stbd-Gear-Nameplate_Model-and-BOM.jpg JPG image
25_Photo_Prior-Deck-Opening_Cut-Line-Layout.jpg JPG image
23_Photo_2019-01_Port-Main-Replacement_ER-Through-Opening-After-Removal.jpg JPG image
29_Photo_2026-07_ER-Main-Engine_Gear-End-and-Exhaust-Lagging.jpg JPG image
32_Photo_2026-07_ER-Marine-Gear-Top-with-Exhaust-Risers-Above.jpg JPG image
Attachment 1 - Cost Schedule.pdf PDF
45_Photo_2026-07_ER-Looking-Aft_Mains-and-Exhaust-Risers-1.jpg JPG image
28_Photo_2026-07_ER-Overview_Between-Mains-Looking-Along-Centerline.jpg JPG image
40_Photo_2026-07_ER-Main-Engine_Exhaust-Risers-and-Cooling-Piping.jpg JPG image
42_Photo_2026-07_ZF-MicroCommander-Control-Processor_Stbd.jpg JPG image
02_EBDG-26075-256-2_FW-Cooling-System-Mods_RevP1-Preliminary.pdf PDF
11_Dwg-C2412-1_Hydrostatic-Curves-of-Form.pdf PDF
43_Photo_2026-07_ZF-MicroCommander-Control-Processor_Port.jpg JPG image
10_Dwg-U193-3_Lines-Plan.pdf PDF
09_Dwg-S2-192_Small-Vessel-Transverse-Frames.pdf PDF
19_Port-Main_Engine-Run-In-Report_Pacific-Power-Group_2018-11.pdf PDF
08_Dwg-U184-56_Transverse-Frames-and-Longitudinal-Section.pdf PDF
30_Photo_2026-07_ER-Main-Engine_Outboard-Side-and-Piping.jpg JPG image
12_Dwg-C2412-2_Cross-Curves.pdf PDF
18_Detroit-Diesel_Exhaust-System-Data_16V-92N-Highlighted.pdf PDF
05_Dwg-U192-S1_General-Scantling.pdf PDF
06_Dwg-U192-S4_Transverse-Frames.pdf PDF
04_Dwg-U192-MI_Shafting-Installation.pdf PDF
15_Silencer-Drawing_Stbd_8in-ANSI150_2022-10-12.pdf PDF
41_Photo_2026-07_ER-Main-Engine_Exhaust-Risers-and-Air-Cleaner.jpg JPG image
46_Photo_2026-07_ER-Looking-Aft_Mains-and-Exhaust-Risers-2.jpg JPG image
17_Detroit-Diesel_16V-92_Engine-Performance-Curve_E4-8162-12-6.pdf PDF
37_Photo_2026-07_Port-Main_Block-Casting-Number-Closeup.jpg JPG image
24_Photo_2019-01_Port-Main-Replacement_Old-Engine-and-Gear-on-Deck.jpg JPG image
35_Photo_2026-07_Port-Gear-Nameplate_Ratio-and-Serial.jpg JPG image
44_Photo_2026-07_Port-Exhaust-Elbow_Material-ID-Tag.jpg JPG image
03_Duramax_SC-424PFDP_Keel-Cooler-Installation-Drawing.pdf PDF
26_Photo_Prior-Deck-Opening_Opening-From-Above.jpg JPG image
07_Dwg-U192-S5_Transverse-Frames.pdf PDF
31_Photo_2026-07_ER-Marine-Gear-and-Foundation.jpg JPG image
22_Photo_2019-01_Port-Main-Replacement_Old-Engine-Visible-Through-Opening.jpg JPG image
34_Photo_2026-07_Port-Gear-Nameplate_Model-and-BOM.jpg JPG image
36_Photo_2026-07_Port-Main_Block-Casting-Number.jpg JPG image
Show all 48

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

TYPE:

MODEL NO.: REV:

SHEET:

DRAWING TYPE:

DATE:DRAWN BY:

CHECKED BY: DATE:

EST. WEIGHT:

ALL DIMENSIONS IN INCHES UNLESS

OTHERWISE SPECIFIED.

TOLERANCES APPLY ON CRITICAL

DIMENSION(S) AS SHOWN BELOW:

1/4" IMP FRAC; 0.25 IMP DEC

6.35 MM METRIC; 2 ANGULAR

HOLD - CRITICAL DIMENSION

THE INFORMATION HEREIN IS THE PROPERTY

OF MAXIM SILENCERS. TRANSMITTAL TO

OTHERS OR USE EXCEPT THAT FOR WHICH

IT IS PROVIDED IS STRICTLY PROHIBITED.

DO NOT SCALE DRAWING.

THIRD ANGLE

PROJECTION

DIM

EXTERNAL FINISH:

APPROVED BY: DATE:

PH: (713) 682-6777

WWW.MAXIMSILENCERS.COM

INFO MAXIMSILENCERS.COM@

76" NOM DIA

"26

10"

8-5/8"

17"

8-5/8"

17"

HEAD

"26

8-5/8"

2"

REF

"13-1/2 "8-13/16

" TYP.7/8 "11-3/4

"13-1/2 "8-13/16

" TYP.7/8 "11-3/4

XX XX MM/DD/YY XXXXXXXXXXXXXXX

REV. NO. REV. BY DATE DESCRIPTION

SILENCER SUPER CRITICAL GRADE

8 M42 C SI

M42-8C2-16583 00

JC 10/11/22

318 LBS 1 OF 1HT BLACK PAINT

NOTES:

1. MATERIAL CARBON STEEL .

2. SILENCER IS DESIGNED TO SUPPORT OWN WEIGHT ONLY.

3. STANDARD MAXIM CONSTRUCTION TOLERANCE APPLY ( 1/4").

4. ALL WELDED CONSTRUCTION.

5. DRAWING SUBJECT TO CHANGE WITHOUT NOTICE.

SALES

TF 10/11/22

WS 10/11/22

OUTLET 8 IN FLANGE

DRILLED TO ANSI #150

INLET 8 IN FLANGE

DRILLED TO ANSI #150

VIEW FROM OUTLET END

1/2" FNPT

DRAIN

INLET OUTLET

VIEW FROM INLET END

Sheet 1
Views
new_view_1
right_2
new_view_3
new_view_5
new_view_6
left_7

File details come from the government source that posted it. Updated .