HB-631 FF04 Paint Schedule.pdf

T

REVISIONS

REV ZONE DESCRIPTION DATE APPROVED

NO. TITLE DRAWING NUMBER

REFERENCES

DOCUMENT DISTRIBUTION RECORD

ISSUE DATE

REV# 0

ABS

NOAA E

HMP PC 1 �

AS =BUILT PROG MGR

PROJ ENG

EL

NA

Pl r-11

ST

HVAC E

0 0 0 0 0 0 0 0 0 REV

JOINER E

NOISE CONTROL E 39 38 37 36 35 34 33 32 31 SHT

PROP SSV E 0 0 0 0 0 0 0 0 0 0 REV

TRAWL SSV E 30 29 28 27 26 25 24 23 22 21 SHT

HPG 1 0 0 0 0 0 0 0 0 0 0 REV

20 19 18 17 16 15 14 13 12 1 1 SHT

ISSUED BY 0 0 0 0 0 0 0 0 0 0 REV

10 9 8 7 6 5 4 3 2 1 SHT

This drawing, design concept and specifications are the property of REVISION STATUS VT Halter Marine, Inc.

and are furnished on a confidential basis with an expressed understandina that DRL NUMBERS they will not be cofried in any manner, used for manufacture, sold trans ered nor used to the de riment of said firm without written permission. the recipienl further a�rees not to disclose these contents hereof to any other parties except or those specific purposes for which this drawing was issued.

VT Halter Marine, Inc. VESSEL

;) Vision Technologies FRV 40 CLASS 63m FISHERIES RESEARCH VESSEL Systems

DRAWN BY ABS APPV TITLE

CM 3/9/05

PAINT SCHEDULE CHECKED BY USCG APPV

FH 3/9/05

APPROVED BY OWNER APPV

HULL NO

I

CAGE CODE

I

SIZE JOB NO. ITEM DELIVERABLE SHEET REV

1953 A M282 631 FF04 1 0

ESTIMATE NO SCALE

00-104 None FILE R: \M282\FUNCTIONALDESIGN\HULL \INWORK\ SHEET 1 OF 39

A PLOT:

AMERON PERFORMANCE COATINGS AND FINISHES GROUP

PAGE 1OF34

STEEL

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

KEEL TO LOWER EDGE OF DEEP LOAD LINE SPOT BLAST DA...1\iAGED AREA TO NEAR WHITE SSPC-SP-10. SANDSWEEP ALL REMAINING

INCLUDING CENTERBOARD TRUNK AREA TO SSPC-SP7.

INTERIOR BELOW WATERLINE, RUBBER,

OTIIBR APPENDAGES BELOW DEEP LOAD

LINE

SPREAD RA TE@ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 RED FULL 8,0 5.0 212 148 8 hrs 6 X . .21 mos

AMERCOAT 235 GRAY FULL 8.0 5.0 212 148 8 hrs 24 X .21 hrs

ABC#3 RED FULL 8.0 5.0 189 132 8 hrs 30 X .21 days

ABC#3 BLACK FULL 8.0 5.0 189 132 8hrs X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Ageut Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max

235 66 235 1 TO l 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

ABC#3 59 NIA NIA NIA 4 hrs 6 hrs 82° 65 40° 100° 85%

(1) Not more than __ % by volume.

Remarks: (2) No coating to be applied when substrate is within 5F of dewpoint.

HULL MARKINGS WITH AMERCOAT 229C WHITE AT 2.0 MILS

STEEL PAGE2OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

SEA CHESTS & HIGH TURBULANCE AREAS SPOT BLAST TO SP,10 & SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMlNATION.

SPRF.AD RATE@ SPEC. Overcoat Time Application Method

SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 RED FULL 8.0 5.0 212 148 8 hrs 6 X .21 mos

AMERCOAT 235 BLACK FULL 8.0 5.0 212 148 8hrs 24 X .21 hrs

AMERLOCK 400 GFK RED FULL 6.0 5.0 266 186 8 hrs 24 X .. 55 hrs

AMERLOCK 400 GFK BLACK FULL 6.0 5.0 266 186 NIA X

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 66 235 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

83 400 3PART 4 hrs 8 hrs 12 hrs 131° 65 32° 90° 85%

400GFK

(3) Not more than __ % by volume.

Remarks: ( 4) No coating to be applied when substrate is within 5F of dewpoint.

STEEL PAGE3OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

DEEP LOAD LINE TO RAIL AND OUTBOARD SPOT BLAST TO SP-10 AND SANTISWEEP ALL REMAINING AREA TO REMOVE ALL SIDE OF BULWARKS CONTAMlNATION.

SPREAD RA TE@ SPEC. Overcoat Time Application Method

SYSTEM INFOR;\1A TION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DIMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

AMEROCAT 235 RED FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

AMERCOAT 229T WHITE FULL 4.0 2.0 361 253 NIA X .21

Solid Curing Mixed Pot Dry at ?OF Flash Thinner (I) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 302H 78 PWD I TO I 4 hrs I hrs 4 hrs 110° +- 10 32° 90° 85%

235 66 235 I TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

229T 45 229 4 TO I 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

Remarks:

HULL MARKINGS 229T: BLACK 2.0 MILS D.F.T.

LIGITTBLUE 2.0 MJLS D.F.T.

DARK BLUE 2.0 MlLS D.F.T.

STEEL PAGE4OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

SPOT BLAT TO SP,10 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPREAD RA, TE@ SPEC. Overcoat Time Application Method

SYSTEM I;s;FORMAT!ON COLOR TYPE WFT OFT OFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21 DIMETCOTE 302H

&\1EROCAT 235 RED FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

AMERCOAT 229T WHITE FULL 4.0 2.0 361 253 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max 302H 78 PWD 1 TO 1 4 hrs 1 hrs 4 hrs 110° +- 10 32° 90° 85%

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

229T 45 229 4TO1 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

(5) Not more than __ % by volume.

AREA: E.)(TERIOR STEEL SIS, DECKHOUSES. VENTS, OVERFLOWS, OVERHEAD, (6) No coating to be applied when substrate is within 5F of dewpoint.

SURF ACES. DECK GEAR LOCKERS, DOORS, STANCHIONS, EXTERIOR VERTICAL

&"ID INCLINED LADDERS. HANDRAILS, BREAKWATERS, VENTILATORS, STACK

BULWARK MOUNTED CHOCKS, DAVITS AND RAILS.

STEEL PAGE5OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ALL EXTERIOR DECKS (6" UP ON VERT. SPOT BLAST TO SP-10 SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

SURFACE) HOUSE TOPS TRAWLWAY, TRAWL CONTAMINATION.

RAMP: ETC (CONTINUED IN REMARKS)

SPREAD RA TE@ SPEC. Overcoat Time Application Method

COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

SYSTEM I?-;FORMA TION

DIMETCOTE 302H

AMEROCAT 235 RED FULL 8.0 5.0 212 148 8 hrs IND X .21

DARK FULL 80 5.0 212 148 NIA X .21

AMERCOAT 450H,

Color #2968 V.1TH N/S #888

GRAY

Solid Curing Mixed Pot Dry at 70F Flash Thinner(!) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max 302H 78 PWD 1 TO I 4 hrs 1 hrs 4 hrs 110° +- 10 32° 90° 85%

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

450HN/S 665 385 I TO I 4 lns 4 hrs 8 hrs 120° 65 32° 120° 85%

(7) Not more than __ % by volume.

Remarks: (8) No coating to be applied when snbstrate is within 5F of dewpoint.

NOTE - 888 NON-SKID ADDED TO FINISH COAT AS REQUIRED!

* AREA - EX

T

ERIOR HATCH COVERS & INBOARD SIDE OF BULWARKS

STEEL

COATINGS SPECIFICATION

AREA:

ALL EXTERIOR FOUNDATIONS, DECK

FITTINGS AND WEATHER HATCH

COAM.INGS.

SYSTH1 ll',;fORMA TION COLOR

DIMETCOTE 302H GREEN

AMEROCAT 235 RED

AMERCOAT 450H

Color Number 2968 Dark

Gray

DARK

GRAY

Solid Curing Product Information Volume Agent

Ratio

302H 78 PWD

450H 66 385

Remarks:

PAGE6OF34

OWNER: JOB:

SURFACE PREPARATION:

SPOT BLAST TO SP-10 AND SANDSWEEP ALL REMAINlNG AREA TO REMOVE ALL

CONTAMINATION.

TYPE

COAT

FULL

FULL

FULL

Mixed Ratio

Base:Cure

I TO I

1 TO 1

WFT

MILS

4.0

8.0

Pot Life

4 hrs

4 hrs

SPREAD RA TE@ SPEC.

DFT DFT Sq.Ft. per Gal

MILS

Theoretical Practical

3.0 417 292

5.0 212 148

5.0 212 148

Dry at 70F Flash Point deg. F

Handle Hard 1 hrs 4 hrs ll0°

4 hrs 8 hrs 120°

Overcoat Time Application Method at 70F Airless Spray Conv. Airless

Min. Max. Brush Roller Spray Spray Nozzle Fan

4 hrs IND. X .21

8 hrs IND X .21

NIA X .21

Thinner (1) Application (2) Ventilation

TempF Humidity Cu.Ft/Gal

Min Max Min Max

+- JO 32° 90° 85%

65 32° 120° 85%

(9) Not more than __ % by volume.

(IO)No coating to be applied when substrate is within SF of dewpoint.

STEEL PAGE 7OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

DECK MACH. ELECTRIC BRAKE, MOTOR SPOT BLAST TO SP-10 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

HOUSING EXTERIOR DECK MOUNTED CONTAMINATION.

CHOCKS, ETC;

(CONTINUED IN REMARKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DlMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

Alv!ERCOAT 235 RED FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

A.'v!ERCOAT 229T BLAC FULL 4.0 2.0 361 253 NIA X .21 K

Solid Curing Mixed Pot Dry at 70F Flash Thinner(!) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TernpF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 302H 78 PWD I TO I 4 hrs I hrs 4 hrs 110° +- 10 32

90° 85%

235 66 235 I TO I 4 hrs 4 hrs 8hrs 120 ° 65 32

° 85%

229T 45 229 4TOJ 4 hrs 4 hrs 8 hrs 105 ° 911 32

90° 85%

( 11) Not rnore than __ % by volume.

Remarks: (12) No coating to be applied when substrate is within SF of dewpoint

CLEATS, BITTS AND F AIRLEADS !

STEEL PAGE8OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

MASTS, BOOMS, TRUSSES, JACK AND ENSIGN SPOT BLAST TO SP-10 SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

STAFF, KlNG POSTS AND SIMILAR FITTINGS CONTAMINATION.

SPREAD RA TE @ SPEC. Overcoat Time Application Method

SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical MJn. Max. Brush Roller Spray Spray Nozzle Fan

DIMETCOTE 302H GREEN FULL 4,0 3,0 417 292 4 hrs IND. X ,21

AMERCOAT 235 RED FULL 8,0 5.0 212 148 8 hrs 72 X .21 hrs

AMERCOAT 229T BUFF FULL 4.0 2,0 361 253 NIA X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg.F

Handle Hard Min Max MJn Max 302H 78 PWD 1 TO 1 4 hrs 1 hrs 4 hrs 110° +- 10 32° 90° 85%

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

229T 45 229 4 TO 1 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

( 13) Not more than __ % by volume.

Remarks: ( 14) No coating to be applied when substrate is within 5F of dewpoint.

STEEL PAGE 9OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ANCHOR SPOT BLAST TO SP-10 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPREAD RA TE@ SPEC. Overcoat Time Application Method

SYSTEM I�FORMA TION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DL\,1.ETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

AMERCOAT 235 BLACK FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Infonnation Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Nlin Max Min Max 302H 78 PWD l TO 1 4 hrs l hrs 4 hrs 110° +- 10 32° 90

° 85%

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

(!5)Not more than __ % by volume.

Remarks: (16) No coating to be applied when substrate is within SF of dewpoint.

STEEL PAGE 10 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ANCHOR CHAIN SPOT BLAST TO SP-10 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPREAD RA TE@ SPEC. Overcoat Time Application Method

COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

SYSTEM INFORMATION

DIMETCOTE 302H

AMERCOAT 235 BLACK FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

Solid Curing Mixed Pot Dry at 70F Flash Thinner(!) Application (2) Ventilation Product Information Volmne Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 302H 78 PWD I TO I 4 hrs I hrs 4 hrs 110°

+-10 32° 90° 85%

235 66 235 I TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

(17) Not more than __ % by volmne.

Remarks: (18) No coating to be applied when substrate is within SF of dewpoint.

MARKINGS: A,,\.1ERCOAT 229C RED AT 2.0 MILS D.F.T.

Al\.1ERCOAT 229C W1IITE AT 2.0 )l.1ILS D.F.T.

AMERCOAT 229C BLUE AT 2.0 MILS D.F.T.

STEEL PAGE 11 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

SPOT BLAST TO SP-10 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPREAD RA TE@ SPEC. Overcoat Time Application Method SYSTE\1 l:S:FORMATIO:s; COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at ?OF Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 RED FULL 8.0 5.0 212 148 8hrs 6 X .21 mos

AMERCOAT 235 OFF SIC -- -- -- -- 8 hrs 6 X X WHITE mos

AMERCOAT 235 OFF FULL 8.0 5.0 212 148 N/A X .21

WHITE

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Ma--c Min Max

235 66 235 I TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120 ° 85%

(19)Not more than __ _ % by volume.

AREA: SALTWATER BALLAST TANKS, PUMPABLE FLXED BALLAST TANKS, (20) No coating to be applied when substrate is within 5F of dewpoint.

SEW ARGE AND GREY WATER TANKS, COFFERDAMS, CENTERBOARD INTERIOR

STEEL ABOVE WATERLINE, VOIDS AND MISCELLANEOUS TANKS.

STEEL PAGE 13 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

CHAIN LOCKER & SUMP SPOT BLAST TO SP-10 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPRFAD RA TE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 WHITE FULL 8.0 5.0 212 148 8hrs 6 X .21 rnos

AMERCOAT 235 RED SIC -- -- -- -- 8 hrs 6 X X rnos

AMERCOAT 235 RED FULL 8.0 5.0 212 148 NIA X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Infonnation Volume Agent Ratio Life Point TernpF Humidity Cu.Ft/Gal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max 235 66 235 I TO l 4 hrs 4 hrs 8 hrs 120° 65 32° 120°

85%

(23) Not more than __ % by volume.

Remarks: (24) No coating to be applied when substrate is within 5F of dewpoint.

STEEL PAGE 17 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

SPOT BLAST TO SP-10 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION,

SPREAD RA TE@ SPEC. Overcoat Time Application Method

SYSTEM J;s;FO!UvlATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 DARK FULL 9.0 6.0 176 124 8hrs IND X .21

GREY

AMERCOAT 235 RED FULL 9.0 6.0 176 124 NIA X .21

Solid Curing Mixed Pot Dry at 70F Flash Thhmer (I) Application (2) Ventilation

Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120 ° 85%

AREA: EXPOSED IN"TERIOR DECKS (6" UP ON VERTICAL SURFACES) IN AUXILIARY (31) Not more than __ % by volume.

MACHINERY AND SERVICE SPACES, WORKSHOPS, STOREROOMS, DECK LOCKERS (3 2) No coating to be applied when substrate is within 5F of dewpoint.

AND SIMILAR SPACES.

STEEL PAGE 18OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: WALKING SURFACES OF FLOOR SURFACE PREPARATION:

PLATES, GRATES, DECKS, AND PLATFORMS SPOT BLAST TO SP-10 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

IN MAIN MACHINERY SPACES. CONTAMINATION.

SPREAD RA TE@ SPEC. Overcoat Time Application Method SYSTEM !/\FORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal ar 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 RED FULL 9.0 6.0 176 124 8hrs IND X .21

AMERCOAT 235 DARK FULL 9.0 6.0 176 124 NIA X .21

GREY

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32 ° 120° 85%

REMARKS: (33) Not more than __ % by volume.

(34) No coating to be applied when substrate is within SF of dewpoint.

PAGE20OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

MACH SPACES BELOW LOWER LEVEL FLOOR SPOT BLAST TO SP-10 SANDSWEEP ALL REMAINING AREA.

PLATES; ETC;

(CONTINUED IN REMARKS) NOTE: ANY REPAIR TO BURN DAMAGE MAY BE POWER TOOL CLEANED

SPREAD RATE@ SPEC. Overcoat Time Application Method

SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray

DIMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X

AMERCOAT 235 RED FULL 9.0 6.0 176 124 NIA. X

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Product Information Volume Agent Ratio Life Point TempF Humidity

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max 302H 78 PWD I TO I 4 hrs I hrs 4 hrs 110° +-10 32 ° 90° 85%

235 66 235 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

(37) Not more than __ % by volume.

Airless Spray

Nozzle Fan

.21

.21

Ventilation Cu.Ft./Gal

Remarks: (38) No coating to be applied when substrate is within 5F of dewpoint.

INCLUDING FLOOR PLATE SUPPORTS, FOUNDATIONS, TANK TOPS BILGE WELLS,

FERROUS PIPE AND OTHER STEEL SURFACES!

ALUMINUM PAGE 22OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

(CONTINUED IN REMARKS) LIGHT SAND SWEEP TO ETCH ALUMINUM

SPREAD RA TE@ SPEC. Overcoat Time Application Method

SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at ?OF Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan AMERCOAT 235 RED FULL 8.0 5.0 212 148 8hrs 72 X .21 hrs

AMERCOAT 229T WlllTE FULL 4.0 2.0 361 253 NIA X .21

Solid Curing Mixed Pot Dry at ?OF Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32 ° 120°

85%

229T 45 229 1 TO 1 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

Remarks: ( 41) Not more than __ % by volume.

EXTERIOR ALUMINUM S/S, DECKHOUSE, VENTS, OVERFLOWS, OVERHEAD (42)No coating to be applied when substrate is within SF of dewpoint.

SURF ACES. DECK GEAR LOCKERS, DOORS, STANCHIONS, EXTERIOR VENTICAL

AND INCLINED LADDERS, HANDRAILS, BREAKWATERS, VENTILATORS, STACK,

BULWARK MOlJNTED CHOCKS, DAVITS AND RAILS!

AM.ERON PERFORMANCE COATINGS AND FINISHES GROUP

ALUMINUM PAGE 23OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

REMARKS LIGHT SAND SWEEP TO ETCH ALUMINUM OR APPLY ONE FULL COAT GALVAPREP PRIMER

SPREAD RA TE@ SPEC. Overcoat Time Application Method

SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brosh Roller Spray Spray Nozzle Fan

AMERCOAT 235 RED FULL 9.0 6.0 176 124 8hrs IND X .21

AMERCOAT 235 DARK FULL 9.0 6.0 176 124 NIA X .21

GRAY

(WITH #888 NON SKID)

Solid Curing Mixed Pot Dry at ?OF Flash Thinner (1) Application (2) Ventilation

Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

REMARKS: (43)Not more than ___ % by volume.

ALL ALUMINUM EXTERIOR DECKS (6" UP ON VERTICAL SURFACES) HOUSE TOPS, (44)No coating to be applied when substrate is within 5F of dewpoint.

EXTERIOR HATCH COVERS, FOUNDATIONS, DECK FITTINGS AND INBOARD SIDE

OF BULWARKS. NON SKID GRIT #888 IS TO BE ADDED TO THE FINISH COAT ON

ALL DECK SURF ACES.

ALUI\UNUM PAGE 24OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ALL EXTERIOR FOUNDATIONS, DECK LIGHT SAND SWEEP TO ETCH ALUMINUM

FITTINGS AND WEATHER HATCH COAMINGS

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at ?OF Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 RED FULL 9,0 6.0 176 124 8hrs IND X .21

AMERCOAT 235 DARK FULL 9.0 6.0 176 124 NIA X .21

GRAY

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Mill Max Min Max

235 66 235 1 TO 1 4 hrs 4 hrs 8 hrs 120 ° 65 32° 120° 85%

AREA ( 45) Not more than __ % by volume.

( 46) No coating to be applied when substrate is within 5F of dewpoint.

ALUMINUM PAGE 25OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURPACE PREPARATION:

INTERIOR PILOTHOUSE OVERHEAD LIGHT SAND SWEEP TO ETCH ALUMINUM

Overcoat Time Apphcation Method SYSTEM INFORMATION COLOR TYPE WFT DPT at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray NcrLZle Fan

AMERCOAT 235 RED FULL 8.0 5.0 212 148 8hrs 72 X .21 hrs

AMERCOAT 229T BLACK FULL 4.0 2.0 361 253 NIA X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Productlnfonnation Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

235 66 235 l TO l 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

229T 45 229 4TO 1 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

REMARKS: ( 47) Not more than __ % by volume.

UNDERSIDE OF PILOTHOUSE VISOR AND OVERHEAD AMERCOAT 229T BLACK ( 48) No coating to be applied when substrate is within 5F of dewpoint.

ALUMINUM PAGE 26FO34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURPACE PREPARATION:

MASTS, BOOMS, TRUSSES, JACK AND ENSIGN LIGHT SAND SWEEP TO ETCH ALUMINUM

STAFF, KINGPOSTS AND SIMILAR FITTINGS

Overcoat Time Application Method SYSTEM Il',;FORMATION COLOR TYPE WFT OFT at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 RED FULL 8.0 5.0 212 148 8hrs 72 X .21 hrs

AMERCOAT 229T BUFF FULL 4.0 2.0 361 253 NIA X .21

Solid Curing Mixed Pot Dry at ?OF Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

235 66 235 1 TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

229T 45 229 4TOI 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

REMARKS: ( 49) Not more than __ % by volume.

(50)No coating to be applied when substrate is within 5F of dcwpoint.

AMERONPERFORMANCECOATINGSANDFINISHESGROUP

ALUMINUM PAGE 27OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

INTERIOR OF ROLL STABILIZATION TANK LIGHT SAND SWEEP TO ETCH ALUMINUM

A1\1D ALUMINUM PORTION OF

CENTERBOARD TRUNK

SPREAD RA TE@ SPEC. Overcoat Time Application Method

SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan AMERCOAT 235 RED FULL 8.0 5.0 212 148 8hrs 6 X .21 mos

OFF -- -- 8 hrs 6 X

AMERCOAT 235 WHJTE SIC -- -- mos

AMERCOAT 235 OFF FULL 8.0 56.0 212 148 NIA X .21

WHITE

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Poiut TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

235 66 235 1 TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

REMARKS: (5l)Not more than __ % by volmne.

(52) No coating to be applied wheu snbstrate is \\ithin 5F of dewpoint.

ALUMINUM PAGE 28OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

EXPOSED INTERIOR LIGHT ETCH THE ALUMINUM

(CONTINUED IN REMARKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method

SYSTEM t:--:FORMA TION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MfLS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 WffiTE FULL 8.0 5.0 212 148 6HRS 3 X .21

DAYS

AMERCOAT 5450 X .21

FILL 7.0 3.0 241 168 NIA

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Infonnation Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max

235 66 235 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

5450 45 NIA NIA NIA 8hrs 12hrs 98°

NIA 32° 90° 85%

REMARKS: (53) Not more than ___ % by volume.

BULKHEADS AND OVERHEADS IN LIVING QUARTERS, PILOT HOUSE, MACHINERY AND ( 54) No coating to be applied when substrate is within 5F of SERv1CE SPACES. WORKSHOPS, STOREROOMS, DECK LOCKERS AND SIMILAR SPACES, dewpoint.

EXPOSED INTERIOR ALUMINUM, INTERIOR RAILINGS, STANCHIONS AND ASSOCIATED

FITTINGS!

SPACES Wlffi JOINER PA..'IBLS #1277 A."ID #1286 -AMERON 5450 (COLOR) RT8205

STATEROOMS. HOSPITAL, PAS SAGE WAYS, SHIPS OFFICE, BRIDGE, MESS ROOM,

LOUNGE AN'D CONFERENCE ROOMS.

SPACES FINISHED IN STAINLESS STEEL-AMERON 5450 (COLOR) RT 1503

SPACES WITH JOINER PA.'IBLS #1201 -AMERON 5450 (COLOR) RT 1505

ALL T & S MODULES, ALL LABS EXCEPT THE FISH AND WET LABS.

NOTE: THAT THE HYDRO LAB IS TO HA VE VER.iv!ICULITE IN THE PAINT.

ALUMINUM PAGE29OF34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

DECKS (6" ON VERTICAL SURFACES) IN LIGHT SWEEP TO ETCH THE ALUMINUM

MACH

(CONTINUED IN REMARKS)

SPREAD RA TE @ SPEC. Overcoat Time Application Method

SYSTH1 !'.'.;FORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray COAT MILS MILS Conv. Airless

Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 DARK FULL 9.0 6.0 176 124 8hrs IND X .21

GREY

AMEROCAT 235 RED FULL 9.0 6.0 176 124 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (l) Application (2) Ventilation

Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

235 66 235 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

REMARKS: (55)Not more than __ % by volume.

AJ.ID SERVICE SPACES, WORKSHOPS, STOREROOMS, EXPOSED INTERIOR DECKS, (56) No coatiug to be applied when snbstrate is within 5F of dewpoint.

DECK LOCKERS AND SIMILAR SPACES!

ALUMINUM PAGE30OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

FLOOR PLATES, DECKS AND PLATFORMS IN LIGHT SWEEP TO ETCH THE ALUMINUM

MACH SPACE

SPREAD RA TE@ SPEC. Overcoat Time Application Method SYSTEM 1:--;FORMA TlO1' COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 235 RED FULL 9.0 6.0 176 124 &hrs IND X .21

AMEROCAT 235 DARK FULL 9.0 6.0 176 124 NIA X .21

GREY

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Vohune Agent Ratio Life Point TempF Humidity Cu.Ft/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

235 66 235 I TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

REMARKS: (57)Not more than __ % by volume.

(58)No coating to be applied when substrate is within 5F of dewpoint.

ALUMI

N

UM

COATINGS SPECIFICATION

AREA:

MACH & FOUNDATIONS

BELOW 200° (CONTINUED IN REMARKS)

SYSTEM INFORMATION COLOR

AMERCOAT 235 EQUIP.

GREY

Solid Curing Productlnformation Volume Agent

Ratio

235 66 235

REMARKS:

OWNER:

SURFACE PREPARATION:

ETCH THE ALUMINUM

SPREAD RA TE @ SPEC.

TYPE WFT DFT DFT Sq.Ft. per Gal

COAT MILS MILS

Theoretical Practical

FULL 8.0 5.0 212 148

Mixed Pot Dry at 70F Flash Ratio Life Point

Base:Cure deg. F

1 TO 1 4 hrs

Handle

4 hrs

Hard

8 hrs 120°

MACHINERY AND FOUNDATIONS WITHIN MACHINERY SPACES ABOVE FLOOR

PLATES WHERE TEMP IS BELOW 200°ft

JOB:

Overcoat Time Application Method at 70F Airless Spray Conv. Airless

Min. Max. Brush Roller Spray Spray Nozzle Fan

NIA X .21

Thinner (I) Application (2) Ventilation

TempF Humidity Cu.Ft/Gal

Min Max Min Max

65 32° 120° 85%

(59)Not more than __ % by volume.

(60) No coating to be applied when substrate is withiu SF of dewpoint.