NEW Attachment 11 - Additional Product Details.pdf

03-465

ASSISTING WITH or PERFORMING AN INSTALLATION IS DONE COMPLETELY AT YOUR OWN RISK!!

ROCKART, Inc. assumes absolutely NO LIABILITY for any type of damage sustained resulting from following the instructions published within this Installation guide. This includes damage to personal property, any personal injury (whether immediate or delayed-onset), loss of life or limb (whether by accident or consequential).

WE STRONGLY RECOMMEND THAT YOU ALWAYS WEAR PROTECTION WHEN AND WHERE APPROPRIATE!

NEVER TAKE RISKS WITH YOUR HEALTH & WELL-BEING!

CALL FOR A BLUE STAKE BEFORE DIGGING!

03-465 ROCKART® Message Center Kiosk Installation Guide

Before you begin, it is recommended that you review this entire installation guide.

PG 2

Message Center Kiosk Parts List

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Optional Products Recommended by Rockart

PART

NUMBER DESCRIPTION PRICE EACH

03-524

3-piece Aluminum Assembly Fixture (for 48” wide sign panels)— used during installation to maintain spacing between Posts without risking damage to your sign panels. The price (less shipping) will be refunded when you return this Fixture, in good condition, to Rockart. RECOMMENDED Qty: 2

$175.00 Refundable Deposit

( less shipping )

08-1015 Touch Up Paint, Rust Texture, 12 oz. aerosol can 12.00

03-481 Qty. = 2

03-486 Qty. = 1

Part Drawings are not to scale.

Parts List

QTY PART# DESCRIPTION

2 03-481 6x6 x 108” Steel Vertical End Post with 2 sign mount tabs

1 03-486 6x6 x 108” Steel Vertical Center Post with 4 sign mount tabs

Additional Tools & Supplies Necessary for Installation

1) Auger and 12” bit

2) Post hole digging tools

3) Wheelbarrow

4) Cement Mix for 3 holes @

(5 cubic feet/hole)

5) Water

6) Hoe

7) (5) 36” long 2x6 wood planks

8) (2-3) 12’ long 2x4 wood planks

9) (2-4) Cement spikes

10) 1 Bottle jack

11) Framer’s level

12) (3) saw horses

13) 12’ Metal Tape Measure

14) 3/8” Hex Driver or adjustable wrench

Before You Start . . .

Please check to be sure that you have received (from ROCKART) all items listed below.

Customer will also need to provide items listed under Additional Tools & Supplies (page bottom) to complete this installation successfully.

03-524 3 pieces, includes hardware kit #03-918

03-918 12@3/8-16 x .75 hex head bolts, 12 nuts and 12 washers

PG 3

Front View Drawing

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Post #2Post #3 Post #1

Aluminum Assembly Fixture #1

Aluminum Assembly Fixture #2

Slotted Sign Panel Mounting Tabs

Important Notes

• Install the Assembly Fixture on the backside of the Slotted Mounting Tabs (See below)

• The angled flange (at top & bottom edges) should point to the FRONT of the kiosk (See below)

• The Assembly Fixture’s edge should be FLUSH against the vertical post (See below)

• Insert a washer between the Slotted Mounting Tab and a nut (to avoid scratching paint) (See below)

|Fr on t S id e of

K io sk

PG 4

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Message Center Kiosk Hole Digging Guide

55.5 inches 55.5 inches

111 inches

18” Dia.

POST #1 POST #2POST #3

Front Side of Kiosk

Mark the CENTER locations of each post:

1 Using a metal tape measure, position the start of it at the spot on the ground where the center of Post (#3) will be and mark the spot.

2 Measure 111 inches to the right of that spot and mark the ground where the center of Post (#2) will be.

3 Without moving the tape measure, mark the ground for the center of Post #1, at 55.5” (center between the previous two marks).

4 Excavate 9” of dirt around each marked spot, so when completed, there will be 3 holes that are 18” diameter and 30” deep.

Applies to: ANY 6x6, 2-PANEL, STRAIGHT KIOSK USING 48”-Wide ROCKART® SIGN PANELS

CALL FOR A BLUE STAKE BEFORE DIGGING!

Review the diagram below:

Each red dot represents where the CENTER of each vertical post should be located.

The green circle centered around each red dot represents an 18” diameter area that should be excavated to a depth of 30” inches.

If installing the kiosk in a location where the ground is NOT LEVEL, these hole depths may need to be adjusted accordingly.

30” deep

18” Dia.

PG 5

Installation Guide

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

What You Will Need to KNOW... These Instructions Apply to Model(s):

Be sure you have reviewed these related sections:

• Kiosk Parts, Tools & Supplies List , PG 2

• Front View Drawing , PG 3

• Hole Digging Guide, PG 4

• This Installation Guide

• Sign Panel Installation Guide (if your kiosk was purchased with sign panels)

#03-465

PLEASE READ FIRST

ROCKART STRONGLY RECOMMENDS the following for the best results:

• For this size Kiosk, we recommend a 2 to 3 person crew.

• Assembly time takes 1 to 2 hours.

• Check to make sure all tools mentioned at the bottom of page 1 are supplied

• Hardware and small tools will ship to you separately via UPS at the same time your Kiosk(s) ships.

• With regards to left/right designations, instructions are written with the assumption that the reader is facing the front of the Kiosk.

• You will need TWO (2) Aluminum Assembly Fixtures (#03-524) to install this kiosk. NOTE: DO NOT

ATTEMPT TO Use Sign Panels in place of the Assembly Fixture! The fixture maintains correct spac-ing between posts while they are being installed. By using them, you need not worry about damaging your actual sign panels, should something go wrong.

• IMPORTANT: Keep the original Aluminum Assembly Fixture shipping boxes. They are necessary to re-turn the fixture(s) for your deposit refund.

Stage I - Assemble & Install the Kiosk Preparation

1 REVIEW Pages 2 & 3. Get familiarized with the kiosk part names & numbers.

2 DIG HOLES – Using the guide on Page 3.

3 ENSURE all holes are only 30” deep for proper viewing height of kiosk sign panels!

4 ASSEMBLE each of the required Aluminum Assembly Fixture(s) using hardware kit #03-918, containing

3/8-16 hex head bolts, nuts and washers.

Installation

1 POSITION a saw horse approx. 7 feet behind each hole. Lay the top capped end of the center Post #1 (#03-486) across a sawhorse positioned so that the slotted sign panel mounting tabs are pointing left and right (parallel to the ground). The bottom end of the post should be suspended over the center hole in the ground. Likewise, PLACE each end Post #2 and #3 (#03-481) in their respective places, with their slotted tabs pointing towards the center of the installation. (See Fig 1)

2 STAND a 2x6, 36” long plank (on end) into each hole, perpendicular to each of the posts. This acts as a guide and allows the posts to slide into the hole with less resistance and with less dirt falling into the hole. (See Fig 2)

PG 6

Installation Guide

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

3 USE remaining 3/8-16 bolts, nuts and washers from hardware kit #03-918 and follow Important Notes on page 3 to INSTALL each of the Aluminum Assembly Fixtures to the BACKSIDE of the four slotted sign mounting tabs (similar to Fig 3) The 1” bent flange of the assembly fixture should be pointing toward the front side of the kiosk.

ENSURE the vertical edges of the Aluminum Assembly Fixture are flush against the vertical edge of the posts before tightening the bolts. Note: Always place a flat washer next to the sign tab slot before applying a nut (see Fig 4)

4 ASSISTED by 2-3 more able persons, gently RAISE the top ends of the assembled kiosk into place, carefully guiding the posts down into the pre-dug holes (similar to Fig 5)

5 STABILIZE the structure using the user-supplied 12ft long 2x4 wood planks & concrete spikes as need-

ed. Tip: placing several large rocks into the open space around the post will help further stabilize it (similar to Fig 6A & 6B).

6 ENSURE all Assembly Fixtures are flush with the vertical posts and all bolts are tight.

7 USING a framer’s level, VERIFY that each Assembly Fixture is level and that each vertical post is plumb

(similar to Fig 7).

Tip: To help level the structure, vertically stack several pieces of 2x4 or 2x6 wooden planks di-rectly under the assembly fixture (on the side that needs to be elevated). Then place a bottle jack atop the stack of wood planks and extend the jack until it pushes against the 1” angled flange at the bottom of the assembly fixture ... continue extending the jack until the structure is level (similar to Fig 8).

8 FOLLOW the manufacturers instructions to MIX concrete and then POUR into each hole (similar to Fig 9) .

Sit back, relax and ALLOW concrete to set properly.

9 After the concrete has properly set, REMOVE the Aluminum Assembly Fixtures.

The Kiosk structure is complete!

You are now ready for STAGE II - Sign Panel Installation.

Fig 2 Fig 3Fig 1

PG 7

Installation Guide

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Fig 7

Fig 4

Vertical Post

Front of Kiosk

1” Angled Flange of Assembly FixtureWasher

Hex Head Bolt

Hex Head Nut

Slotted Sign Panel Mounting Tab

Fig 5

Fig 9

Fig 6A

Fig 8

Fig 6B

Don’t forget to return the ALUMINUM ASSEMBLY FIXTURES back to ROCKART.

Follow the directions on the included RMA Form to return-ship undamaged & usable Fixtures back to Rockart, Inc. Use the original shipping boxes, if possible. (No need to return the hardware used to assemble them.) After the fixtures have been received by Rockart, you will receive a refund of the security deposit (less shipping charges).

PG 8

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Message Center Kiosk STAGE II - Sign Panel Install Guide

Installation Note for Fully-Enclosed* Sign Panels:

Before mounting a Fully-Enclosed* Sign Panel to the Kiosk, check the orientation of the removable side rail. Fully-Enclosed sign panel displays will have 3 to 5 bolts embedded within this rail (circled on left) that secure the entire display and when installed, and should be along the right side.

For sign panels that include Routed Text across the header and/or footer, verify that the text is displayed as desired.

How to properly install a VandlGard® tamper-resistant nut:

If your kiosk sign panel included tamper-resistant mounting hardware, the odd-looking nuts are tamper resistant and should be installed as follows:

Start by threading the wide, tapered end of the cone-shaped nut onto the end of the bolt as shown by the green arrow (see top image, left). Twist clock-wise with fingers & thumb, until snug.

Using a hex wrench or pair of pliers, continue to tighten the Hex part of the nut until the hex part breaks off... leaving the conical part behind (see bottom image, left). Discard the hex nut. ... all done!

* A Fully-Enclosed Sign Panel protects the displayed content completely (on every side). These models feature a removable side rail (on either the left or right side), and a protective clear polycarbonate cover that is also removable.

Opening a “fully-enclosed” Sign Panel:

To open a Fully-Enclosed* Sign Panel (to change out the signage) you will need the special YELLOW colored Hex tool (included with fully-enclosed displays) to remove the 3 to 5 bolts along the right side (don’t lose them!). Remove the side rail. Grab the tail-end of the flexible security rod sitting on top of the clear polycarbonate cover, and pull it completely out of the channel through the opening (see image, left).

Slide the clear polycarbonate cover over enough to allow you to grasp it firmly on both left & right sides. Lift it straight up, pushing the top edge deeper into the top channel. Now, pivot the bottom edge of the cover out from the display (i.e., towards yourself). Take note which side was facing out (and when done, return it accordingly).

Place the clear cover in an area that is clean as possible while swapping out content.

When finished, simply follow these steps in reverse order. Don’t forget to RE-INSERT the flexible security rod ! Finally, use the YELLOW hex tool as before to secure the side access rail using the same bolts removed earlier.

Flexible Security Rod

Special Hex tool (#08-619) used to open fully-enclosed sign panels (included)

Important information for ROCKART® Sign Panels and Message Center Kiosks

PG 9

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Message Center Kiosk Sign Panel Install Guide

Vertical Steel Post

Tackboard Sign

Slotted Sign Panel Mounting Tab

Plastic Flat Washer

VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex

2“ Dia. Stainless Steel Fender Washer

2“ Dia. Stainless Steel Fender Washer

Carriage Bolt

Black Nylon Carriage Bolt Adapter

FRONT of Kiosk

Clear Polycarbonate Cover (Optional) Vertical Steel Post

Slotted Sign Panel Mounting Tab

Plastic Flat Washer

VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex

2“ Dia. Stainless Steel Fender Washer

2“ Dia. Stainless Steel Fender Washer

Carriage Bolt

Black Nylon Carriage Bolt Adapter FRONT of Kiosk

Tackboard Sign

Header / Footer

Vertical Steel Post

Ballistic Tack Board Sign

Header / Footer

Header / Footer

Slotted Sign Panel Mounting Tab

Plastic Flat Washer

VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex

2“ Dia. Stainless Steel Fender Washer

2“ Dia. Stainless Steel Fender Washer

Carriage Bolt

Black Nylon Carriage Bolt Adapter FRONT of Kiosk

Tack Board Only #03-901 ASSEMBLY KIT

Header / Footer (Single-Sided) #03-903 ASSEMBLY KIT

Header / Footer (Double-Sided) #03-904 ASSEMBLY KIT

Using included hardware from #03-901, follow the hardware stacking guide (right) to secure each corner of the sign panel to the kiosk.

Using included hardware from #03-903, follow the hardware stacking guide (right) to secure each corner of the sign panel to the kiosk.

Using included hardware from #03-904, follow the hardware stacking guide (right) to secure each corner of the sign panel to the kiosk.

For Single- and Double-sided Sign Panels having 1 mounting hole in each corner

PG 10

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Message Center Kiosk Removing Polycarbonate Cover

Removing the Cover

Important! DO NOT REMOVE the 4 Corner Bolts that secure the Sign Panel to the Kiosk!

1 USE the special YELLOW hex wrench (included with your sign panel) to REMOVE the tamper-resistant bolts usually located on the right side of a sign panel (from the Front side of kiosk). Don’t lose these bolts! The nuts are embedded in either the tack-board (for single-sided panels) or in a matching removable side rail on the opposing side (double-sided panels) and should stay in place while the bolts are removed.

Remove bolts marked as “1” (see figure, right).

2 REMOVE the side rail (or rails) of the Sign Panel and set aside.

3 PULL OUT the Flexible PLASTIC ROD inserted into the space above the polycarbonate cover. Don’t lose it! (This important security feature prevents vandals from removing the cover themselves)

4 SLIDE the cover over about an inch, so you can FIRMLY GRASP both sides.

5 LIFT the cover straight up into the top grooved channel then PIVOT the bottom edge towards your body, until it is completely free. Set the cover aside (somewhere clean) so it can be replaced with the same side facing outward. (Remember which side faces out... since UV or Anti-Graffiti films are usually applied to one side only.)

6 SWAP OUT SIGN CONTENT

Replacing the Cover

NOTE: Replace the cover with same side facing out (UV or Anti-Graffiti films are usually applied to one side only).

1 GRASP the left & right sides of the cover, INSERT the top edge fully into the top grooved channel.

2 PIVOT the bottom edge of cover to line up with the bottom grooved channel. Carefully RELEASE it, allowing it to sit in the bottom grooved channel.

3 GENTLY SLIDE the cover left/right (toward the non-removable side rail) until it cannot go any further.

4 RE-INSERT the Flexible PLASTIC ROD into the gap just above the cover itself.

5 Finally, REPLACE the vertical rail(s) and secure with the tamper-resistant bolts using the special YELLOW hex wrench.

Stuff You Need to Know These Instructions Apply to:

• You’ll need the specially-keyed, L-shaped YELLOW hex wrench #08-619 (included with fully-enclosed ROCKART® Sign Panels).

• The tackboard is VERY dense; thumbtacks and push-pins cannot penetrate it. Consider using an industrial staple gun with heavy duty staples.

• Keep the inside of the sign panel as clean as possible: While performing the steps below, avoid placing removed components directly on the ground. Using a tarp or other ground cover is recommended!

ROCKART®

Standard Sign Panels

(Full-sized & Fully-Enclosed Single-or Double-sided Sign Panels)

IF YOU ARE REPLACING A DAMAGED COVER: If there are any protective (opaque) liners applied to either side of a polycarbonate cover REMOVE the protective liner from the cover as soon as possible. If the liner is exposed to sunlight for extended periods, it may be very difficult to remove.

Instructions only for “fully-enclosed” full-sized ROCKART® Sign Panels

SCENIC VISTA

1/4 MILE

HOLES 1" CENlER TO CENlER

ANTI-VANDAL FASlENER ASSEMBLY

1/2" RADIUS

WHllE MESSAGE AND WHllE BORDER ON A BROWN BACKGROUND

~17"x38" REFLECTORIZED SIGN CONSTRUCTED OF PORCELAIN STEEL WllH BEADED TEXT OR EQUAL

ANTI-VANDAL FASlENER ASSEMBLY

1-3/4" X 1-3/4" BREAKAWAY TUBULAR SlEEL POSt WllH END CAP AND ANCHOR SLEEVE

SIGN POST

HOLE DIAMElER 7 /16"

80" MIN, BREAKING POINT

-h

3/8" HOT DIPPED GALVANIZED HEX

BOLT WllH WASHER AND HEX LOCK NUT

ANCHOR SLEEVE

--- SUBGRADE

SIGN POST ANCHOR 3'

j

FRONT VIEW

NOlES: 1. DRIVE SIGN POST ANCHOR TO WllHIN 3 TO 4 INCHES OF SURFACE. ANCHOR POST IS NEXT SIZE LARGER SECTION lHAN SIGN POST.

2. PRE-CUT ANCHOR SLEEVE (OF NEXT SIZE LARGER TUBE) SO THAT lHE HOLES WILL MATCH AND STILL BE FLUSH WITH TOP CF SIGN POST ANCHOR. DRIVE ANCHOR SLEEVE UNIT UNTIL HOLES MATCH AS NOTED ABOVE. lHEN DRIVE BOlH THE SIGN POST AND ANCHOR SLEEVE UNTIL ONE HOLE IS LEFT

EXPOSED ABOVE GROUND FOR BOLT CONNECTION.

3. MANUFACTURER'S DRIVING CAP SHALL BE REQUIRED FOR INSTALLATION.

4. POST MA TERI AL SHALL CONFORM TO ASTM A-366, 12 GAGE STEEL WITH A YIELD STRENGlH OF 25,000 PSI.

5. SIGNS TO BE PROVIDED BY FOREST SERVICE. ALL OTHER POSTS AND SUPPORT TO BE FURNISHED

AND INSTALLED BY CONTRACTOR. CONTRACTOR SHALL PICK UP GOVERNMENT PROVIDED SIGNS AT HENSHAW FIRE STATION. SIGNS SHALL BE INSTALLED IN ACCORDANCE WllH MUTCD GUIDELINES AND

FOREST SERVICE SPECIFICATIONS SECTION 633.

NOlES:

ANTI-VANDAL FASlENER ASSEMBLY

SIGN

ANCHOR SLEEVE

IJ!Ilcitu.ql 1='---------

SIDE VIEW OF RECREA 11ON GUIDE SIGN

SIGN SHOULD BE VERTICALLY MOUNlED OR AT RIGHT ANGLES TO lHE DIRECTION OF AND FACING lHE TRAFFIC lHAT lHEY ARE INTENDED TO SERVE. DESIGN LAYOUT SHOWING INTERLINE SPACING, EDGE SPACING AND OlHER SPECIFICATION DETAILS SHALL BE AS SHOWN IN THE "STANDARD HIGHWAY SIGNS" BOOK. lHE MINIMUM LAlERAL OFFSET FROM THE EDGE OF SHOULDER (OR IF NO SHOULDER EXISTS, FROM lHE EDGE OF PAVEMENT) TO lHE NEAR EDGE OF ROADSIDE MOUNTED SIGN SHALL BE 6 FEET, AND SHALL BE LOCATED APPROXIMAlELY ONE QUARTER MILE IN EACH DIRECTION FIROM THE ENTRANCE TO lHE SITE.

(b) RECREA 11ON GUIDE SIGN

Henshaw

SCENIC VISTA

RS-1 Sign

2"x 6" Rough Sawn

1 /2" Dia. Threaded Rod with washer and nut countersunk

Sawn

Treated Post

------+--+------+-+�f-----\-+--+----

<-Compacted Soil \ 1 1 , around posts

I I / / / 1 /2" Threaded Rod 1-r-?

I I I

\.- -' '--...J L..�

Mount Sign with 1 /2" threaded rod and vandlegard nut with neoprene washer on each side, typical.

NOTE: SIGN BOARDS, SHIELDS AND USDA CREDIT LINES PROVIDED BY FOREST SERVICE. ALL OTHER

POSTS AND SUPPORT TO BE FURNISHED AND INSTALLED BY CONTRACTOR. CONTRACTOR SHALL

PICK UP GOVERNMENT PROVIDED SIGNS AT HENSHAW FIRE STATION. SIGN SHALL BE INSTALLED AT LOCATION SHOWN AND IN ACCORDANCE WITH FOREST SERVICE SPECIFICATIONS SECTION 633.

@) RECREA 11ON SITE IDENTIFICA 11ON SIGN

USDA

FOREST

SERVICE

PACIFIC

SOUTHWEST

REGION

RS

NO. DATE REVISIONS

E--<

� ....:l > w

0 z ...... 0 E--<

Cl

....:l z

....:l t3 i!i ..

13! �� !l:z c,z

AIE

PROJECT NUMBER

DESIGNED BY

MATHER

DRAWNBY

PACE

CHECKED BY

MATHER

CHECKED BY

EASTWOOD

DATE

1DFEB03

SCALE

NTS

DRAWING

SHEET 8 OF 10

GraceBassett Highlight

GraceBassett Text Box

GraceBassett Text Box

GraceBassett Text Box

GraceBassett Text Box

GraceBassett Text Box

GraceBassett Text Box

GraceBassett Text Box

SAMPLE SITE SIGN DETAIL

CLEVELAND National Forest

CHA'CHAANY HAMUK

CONCRETE

FOOTING TYP.

NATIVE SOIL

FINISHED

AGGREGATE

SURFACE

INSTALL 2-PANEL

METAL BULLETIN

BOARD (SEE NOTES)

NOTES:

1. BULLETIN BOARD SHALL PREFABRICATED METAL 6"X6" 10-PANEL ANGLE BULLETIN BOARD (SIZES AS SHOWN).

MANUFACTURED WITH BROWN POWDER COAT FINISH AS MANUFACTURED BY PANNIER OR APPROVED EQUAL.

2. BILLBOARD PARTS INCLUDE POWDER COATED METAL FRAME WITH TUBULAR STEEL POSTS, POWDER COATED BROWN

MOUNTING BOARDS WITH FRAMING ONE PANEL WITH "CLEVELAND National Forest" ON TOP AND "Cha'chaany Hamuk TRAIL HEAD" ON BOTTOM IN YELLOW AS SHOWN IN THE DRAWINGS, AND FIXTURES NECESSARY FOR INSTALLATION AND TAMPER RESISTANT BOLTS AS MANUFACTURED BY PANNIER, 345 OAK ROAD, GIBSONIA, PA 15044; ROBIN HADDEUS 724.265.4900 OR APPROVED EQUAL. VERIFY WITH MANUFACTURER FOR ALL NECESSARY PARTS FOR

INSTALLATION.

3. SEE SPECIFICATION 101110 FOR ADDITIONAL REQUIREMENTS.

BULLETIN BOARD TYPICAL DETAIL SECTION A-A

NTS

4" X 6" TREATED

POST (TYP.)

NATIVE SOIL WITH

APPROVED COMPACTED

BACKFILL AROUND POSTS

(TYP.)

SIGN BOARD RSEC-C (SEE FS

MANUAL EN-7100-15)

FINISHED GRADE

R

R R

R

NOTES

1. DIMENSIONS FOR SIGN INSTALLATION ARE SCHEMATIC.

2. SIGNS WILL BE LOCATED BY THE CONTRACTING OFFICER.

3. SEE SPECIFICATION 101415 FOR SIGN POST MATERIALS AND SPECIFICATION

101415 FOR HDPE SIGN FABRICATION.

4. ALL SIGNS SHALL BE INSTALL USING VANDAL RESISTANT BOLTS AND NUTS.

5. ALL SIGNS SHOULD BE IN ACCORDANCE WITH FS MANUAL EM 7100-15

CHAPTER7B.

MINOR SITE ID SIGN TYPICAL

(REQUIRES DOUBLE 4" X 6" POST BASE)

TOP LEGEND

BROWN LETTER (FEDERAL STANDARD 595 NO. 20059) ON YELLOW-CREAM (FEDERAL STANDARD 595 NO. 23695) BACKGROUND

BOTTOM LEGEND

YELLOW-CREAM (FEDERAL STANDARD 595 NO. 23695) ON BROWN LETTER (FEDERAL STANDARD 595 NO. 20059) BACKGROUND

MINOR SITE ID SIGN RSE-C TABLE

SIGN # SIGN PANEL TEXT PANEL DIMENSIONS LAYOUT DIMENSIONS MEASURED

FROM BOTTOM OF PANEL LETTER SIZE MATERIAL

FACILITY NAME

(UPPER PANEL)

FACILITY

TYPE

(LOWER

PANEL)

H L R S A B C

FACILITY NAME

ASA SERIES D

(INITIAL CAPS

LOWER CASE)

FACILITY

TYPE ASA

SERIES D

(UPPER

CASE)

RSE-3 Cha'chaany Hamuk TRAILHEAD 2'-0" 5'-0" 0'-5" 0'-4 3/4" 0'-3" 0'-3" 0'-9 1/2" 0'-4" 0'-4" HDPE

2'-0" DIA.

"-3

0"

H L

5'- 0"

3'- 0"

(M

IN

5 X SIGN LENGTH

A

B C

PANEL B 36 48

PANEL G 36 48

PANEL C 18 48

PANEL F 18 48

PANEL A 18 48

PANEL H 18 48

PANEL J 18 48

PANEL I 18 48

PANEL D 18 48

PANEL E 18 48

BULLETIN BOARD TYPICAL DETAIL

NTS

FALL WATER IS

NOT FLOWING

STAGNANT FLIP DOWN/UP

SIGN CAN BE

CLOSED DURING

WET SEASONS

LOCKING SLIDE BOARD

CHANGES STATUS

OPEN(WHITE ON

GREEN)/CLOSED (WHITE

ON RED)

Cha'chaany Hamuk AREA

OPEN

760-788-0250

Cha'chaany Hamuk AREA

CLOSED

760-788-0250

STATUS SIGN DETAILS

NTS

FALL WATER IS

NOT FLOWING

STAGNANT

Cha'chaany Hamuk AREA

OPEN

760-788-0250

RED ON TAN

WHITE ON TAN

S

L

H

DRAWN

DESIGNER

STAMPS, LOGOS, AND SEALS

PROJECT NAME

DRAWING TITLE

CHECKED

ARCHIVE NO.

DATE

PROJECT NO.

DRAWING SHEET NO.

DATENO.

REVISION / ISSUE

OFSHEET

United States Department of Agriculture Forest Service

1/1 4/2

2 1 1:

CG

OM

EZ

DA

VI

LA C

:\U

SE

RS

\C

GO

ME

ZD

AV

IL

A\

DO

CU

ME

NT

S\

PR

OJ

EC

TS

\F

OR

ES

TS

\C

LE

VE

LA

ND

NF

\E

NG

-2 1-

-0

\01

PR

OJ

EC

TD

AT

A\

CA

D\

TH

RE

ES

IS

TE

RS

TH

_D

ET

AI

LS

_2

4.D W

G

(R05)

PACIFIC SOUTHWEST REGION

CHA'CHAANY

HAMUK TRAILHEAD

CLEVELAND NATIONAL

FOREST

PALOMAR DISTRICT RANGER

BULLETIN BOARD AND

SITE ID SIGNS DETAILS

03/30/2021 -

C.GÓMEZ

C.GÓMEZ

S.BINGHAM

C-16 18 29

AutoCAD SHX Text Cha'chaany Hamuk

AutoCAD SHX Text

TRAILHEAD

AutoCAD SHX Text Facility Name

AutoCAD SHX Text

FACILITY TYPE

AutoCAD SHX Text A

AutoCAD SHX Text A

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text V

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text D

AutoCAD SHX Text E

AutoCAD SHX Text P

AutoCAD SHX Text A

AutoCAD SHX Text R

AutoCAD SHX Text T

AutoCAD SHX Text M

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text T

AutoCAD SHX Text O

AutoCAD SHX Text F

AutoCAD SHX Text A

AutoCAD SHX Text G

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text U

AutoCAD SHX Text L

AutoCAD SHX Text T

AutoCAD SHX Text U

AutoCAD SHX Text R

AutoCAD SHX Text E

GraceBassett Text Box

GraceBassett

3'-0" FOR 4"X4" POSTS

4'-0" FOR 6"X6" POSTS

SE

E

SI

GN

IN

ST

AL

LA

TI

ON

DE

TA

ILS

3'- 0"

F

OR

4" X4

" P

OS

TS

4'-

0" F

OR

6"

X6 " P

OS

TS

RESERVE

PARKING

VAN ACCESSIBLE

12" WIDE VAN

ACCESSIBLE SIGN

4" X 4" TREATED POST

GREEN LEGEND AND

BORDER/ WHITE SYMBOL ON

BLUE BACKGROUND ON

WHITE MAJOR BACKGROUND

SIGN BOARD

LETTER SIZE VARIES

16" X 3" BOLTS (TYP.)

REFLECTIVE WHITE LEGEND

ON REFLECTIVE BROWN

BACKGROUND (TYP.)

4"X4" TREATED POST (TYP.)

SURFACE AREA

ACCESSIBLE PARKING SIGN SINGLE POST SIGN DOUBLE POST SIGN

SIGN INSTALLATION DETAILS

EDGE OF

TRAVELED

WAY EDGE OF

TRAVELED

WAY

SIGN LIST

SINGLE POST SIGNS (4"X4")

SIGN DESCRIPTION SIGN # QUANTITY SIZE

NOTES COLOR

#1 STOP SIGN W3-1 3 30 X 30 WHITE ON RED

#2

ACCESSIBLE PARKING

W/ VAN ACCESSIBLE

PLAQUE

R7-8-12

R7-8A 2 WHITE ON BROWN,

BLUE SYMBOL

#3 CHA'CHAANY HAMUK

TRAILHEAD FRD-2-2 1 WHITE ON BROWN

#4 CHA'CHAANY HAMUK

TRAILHEAD FRD-2-2 1 WHITE ON BROWN

#5 TRAILHEAD

ENTRANCE FRD-2-2 1 WHITE ON BROWN

#6 NOT SUITABLE FOR

TRAILERS OR RV'S FRD-2-2 1 BLACK ON WHITE

#7 CURVE LEFT W1-10L 1 30 X 30 BLACK ON YELLOW

#8 CURVE RIGHT W1-10R 1 30 X 30 BLACK ON YELLOW

#9 AUTHORIZED VEHICLES

ONLY R5-11 1 BLACK ON WHITE

#10 NO MOTOR VEHICLES R5-3 1 BLACK ON WHITE

#11 NO PARKING ANY TIME AR-220 2 RED ON WHITE

#12 RESTRICTED ACCES 1 BLACK ON WHITE

#13 WRONG WAY R5-1A 1 WHITE ON RED

#14 HAIRPIN CURVE RIGHT W1-11R 1 30 X 30 BLACK ON YELLOW

#15 HAIRPIN CURVE LEFT W1-11L 1 30 X 30 BLACK ON YELLOW

#16 TRUCK TURN AROUND

AHEAD 1 BLACK ON YELLOW

#17 SITE IDENTIFYING SIGN 1 WOOD

#18 TRAIL STATUS SIGN 1 WHITE ON BRWON

#19 15 MPH SPEED LIMIT R2-1 1 12 X 18 BLACK ON WHITE

#20 5 MPH SPEED LIMIT R2-1 2 12 X 18 BLACK ON WHITE

NOTES:

1. SEE EM 7100-15 MANUAL FOR FRD SIGN LAYOUT REQUIREMENTS.

2. ALL SIGNS BOARDS INSTALLED ON SINGLE POSTS SHALL BE CENTERED.

3. DIMENSIONS FOR SIGN INSTALLATION ARE SCHEMATIC.

4. SEE SPECIFICATION 101400 FOR SIGN POST AND MATERIALS.

5. ALL SIGNS SHALL BE INSTALLED USING VANDAL RESISTANT BOLTS AND NUTS.

6. INSTALLATION DATE AND VANDAL WARNING LABELS SHALL BE INSTALLED ON

ALL SIGNS IN ACCORDANCE WITH FS MANUAL EM 7100-15

7. ALL SIGN SHALL MEET MUTCD AND FOREST SERVICE STANDARDS.

8. CLEAR VEGETATION AS NEEDED TO MANTAIN VISIBILITY OF SIGNS. CLEARING

SHALL BE HANDLED IN ACCORDANCE WITH SPECIFICATION 311000.

9. THE BACK OF ALL SIGNS SHALL BE PAINTED OR POWDER COAT BROWN.

3'- 0"

7'- 0"

1"

1'- 6"

VA

RI

ES

3" VA

RI

ES

VARIES

VARIES

5 X SIGN

LENGTH

6' TO 12' COUNTY

AND FS ROADS

7'

MI

N.

6' TO 12' COUNTY

AND FS ROADS

7'

MI

N.

SE

E

SI

GN

IN

ST

AL

LA

TI

ON

DE

TA

ILS

DRAWN

DESIGNER

STAMPS, LOGOS, AND SEALS

PROJECT NAME

DRAWING TITLE

CHECKED

ARCHIVE NO.

DATE

PROJECT NO.

DRAWING SHEET NO.

DATENO.

REVISION / ISSUE

OFSHEET

United States Department of Agriculture Forest Service

1/1 4/2

2 1 1:

CG

OM

EZ

DA

VI

LA C

:\U

SE

RS

\C

GO

ME

ZD

AV

IL

A\

DO

CU

ME

NT

S\

PR

OJ

EC

TS

\F

OR

ES

TS

\C

LE

VE

LA

ND

NF

\E

NG

-2 1-

-0

\01

PR

OJ

EC

TD

AT

A\

CA

D\

TH

RE

ES

IS

TE

RS

TH

_D

ET

AI

LS

_2

4.D W

G

(R05)

PACIFIC SOUTHWEST REGION

CHA'CHAANY

HAMUK TRAILHEAD

CLEVELAND NATIONAL

FOREST

PALOMAR DISTRICT RANGER

SIGN INSTALLATION

DETAILS

03/30/2021 -

C.GÓMEZ

C.GÓMEZ

S.BINGHAM

C-17 19 29

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text V

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text D

AutoCAD SHX Text E

AutoCAD SHX Text P

AutoCAD SHX Text A

AutoCAD SHX Text R

AutoCAD SHX Text T

AutoCAD SHX Text M

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text T

AutoCAD SHX Text O

AutoCAD SHX Text F

AutoCAD SHX Text A

AutoCAD SHX Text G

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text U

AutoCAD SHX Text L

AutoCAD SHX Text T

AutoCAD SHX Text U

AutoCAD SHX Text R

AutoCAD SHX Text E

GraceBassett Text Box

GraceBassett

43.9 23.9

.6

NOTES:

· GALVANNEALED STEEL CONTRUCTION.

· STAINLESS STEEL HINGES.

· U.V RESISTAN POWDER COAT FINISH.

MODEL HA2-CH FROM BEAR SAVER, BEARSAVER, ONTARIO,

CALIFORNIA 91761, PHONE 1-800-851-3887, FAX 1-909-605-7780.

CONTACT: STEVE THOMPSON, 909-212-5386 -OFFICE,

714-225-4306 - CELL. OR APPROVED EQUAL

FOREST SERVICE

LOGOS DECAL, 10"X11"

COLOR YELLOW

DECAL AMERICAN FLAG 10",

COLOR

DRAWN

DESIGNER

STAMPS, LOGOS, AND SEALS

PROJECT NAME

DRAWING TITLE

CHECKED

ARCHIVE NO.

DATE

PROJECT NO.

DRAWING SHEET NO.

DATENO.

REVISION / ISSUE

OFSHEET

United States Department of Agriculture Forest Service

1/1 4/2

2 1 1:

CG

OM

EZ

DA

VI

LA C

:\U

SE

RS

\C

GO

ME

ZD

AV

IL

A\

DO

CU

ME

NT

S\

PR

OJ

EC

TS

\F

OR

ES

TS

\C

LE

VE

LA

ND

NF

\E

NG

-2 1-

-0

\01

PR

OJ

EC

TD

AT

A\

CA

D\

TH

RE

ES

IS

TE

RS

TH

_D

ET

AI

LS

_2

4.D W

G

(R05)

PACIFIC SOUTHWEST REGION

CHA'CHAANY

HAMUK TRAILHEAD

CLEVELAND NATIONAL

FOREST

PALOMAR DISTRICT RANGER

CONCRETE WASTE

RECEPTACLE DETAILS

03/30/2021 -

C.GÓMEZ

C.GÓMEZ

S.BINGHAM

C-12 14 29

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text V

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text D

AutoCAD SHX Text E

AutoCAD SHX Text P

AutoCAD SHX Text A

AutoCAD SHX Text R

AutoCAD SHX Text T

AutoCAD SHX Text M

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text T

AutoCAD SHX Text O

AutoCAD SHX Text F

AutoCAD SHX Text A

AutoCAD SHX Text G

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text U

AutoCAD SHX Text L

AutoCAD SHX Text T

AutoCAD SHX Text U

AutoCAD SHX Text R

AutoCAD SHX Text E

GraceBassett Text Box

SAMPLE TRASH/RECYCLE CONTAINER DETAIL

GraceBassett