NEW Attachment 10. Product Details.pdf

MODEL# 100FSS-M - CONCRETE PICNIC TABLE,

FS LEG WITH WOODGRAIN TOP AND SEATS FROM #114

CRESTLINE GROUP CAMPGROUND - CLEVELAND NF

OUTDOOR CREATIONS, INC. SCALE: 1” = 32” MAN. TOL. +/- 1/4"

DRAWN BY: MNC 2/7/24

OUTDOOR

CREATIONS

INC.

2270 Barney Street Anderson, CA 96007

(530) 365-6106

FAX (530) 365-5129

NOTES:

1. Concrete mix design to include a mixture of Portland Cement, water, coarse and fine aggregates, pure mineral oxide coloring agents (when applicable) to yield a minimum compressive strength of 5000 psi.

2. Final product shall be reinforced with #4 and #5 rebar grid.

3. Product is cast in 1-piece with no assembly required.

4. Hairline cracks may develop over time. These are not structural failures, but inherent characteristics of the material itself.

5. Air pockets are a common occurrence in precast products.

The frequency and size of air pockets are variable and to be expected, especially on vertical surfaces.

6. Concrete corners and edges will chip if not handled according to guidelines. Patch kits are available but may or may not blend and can be variable.

7. There is a level of care and maintenance associated with your product and is the responsibility of the end user. Choosing the right sealer can help minimize those costs.

WEIGHT: 2500 LBS

TEXTURE:

Top/Seats: Woodgrain/Smooth Legs: Smooth

COLOR:

Top/Seats: ODC Kahlua Legs: Natural SEALER: Standard Acrylic

CUSTOMER APPROVAL x________________________________________

LEG DETAIL (SCALE 1"=24")

96"

35"

4"

4" 32

65"

11"

4" 4"

24"

4" 44"

55"

8"

22 1/4"

22 3/4"

7 1/4"

3/

4"

15 1/4"

* Wheelchair Accessibility available at both ends of table to meet A.D.A. Guidelines

MODEL #103 - 72" CONCRETE SERVICE TABLE OUTDOOR CREATIONS, INC. SCALE: 1” = 32”

DRAWN BY: MNC

OUTDOOR

CREATIONS

INC.

2270 Barney Street Anderson, CA 96007

(530) 365-6106

FAX (530) 365-5129

NOTES:

1. Concrete mix design to include a mixture of Portland Cement, water, coarse and fine aggregates, pure mineral oxide coloring agents (when applicable) to yield a minimum compressive strength of 5000 psi.

2. Final product shall be reinforced with #4 and #5 rebar grid.

3. Product is cast in 1-piece with no assembly required.

4. Hairline cracks may develop over time. These are not structural failures, but inherent characteristics of the material itself.

5. Air pockets are a common occurrence in precast products.

The frequency and size of air pockets are variable and to be expected, especially on vertical surfaces.

6. Concrete corners and edges will chip if not handled according to guidelines. Patch kits are available but may or may not blend and can be variable.

7. There is a level of care and maintenance associated with your

WEIGHT: 2000 LBS

COLOR:

SEALER:

SIDE ELEVATION

PLAN

ELEVATION

31"

7" 14"

72" 4 "

34 "

CUSTOMER APPROVAL x________________________________________

Threaded inserts in legs for mounting dowels(1 per leg)

* (2) 3/4” x 8” coil rods provided per table for mounting

MODEL# 427 - TIMBER BENCH WITH BACK WITH ARMRESTS

18" x 27" x 72"

OUTDOOR CREATIONS, INC. SCALE: 1” = 18” MAN. TOL. +/- 1/4"

DRAWN BY: MNC

OUTDOOR

CREATIONS

INC.

2270 Barney Street Anderson, CA 96007

(530) 365-6106

FAX (530) 365-5129

NOTES:

1. Concrete mix design to include a mixture of Portland Cement, water, coarse and fine aggregates, pure mineral oxide coloring agents (when applicable) to yield a minimum compressive strength of 5000 psi.

2. Final product shall be reinforced with #4 and #5 rebar grid.

3. Product is shipped as 1-piece with no assembly required.

4. Hairline cracks may develop over time. These are not structural failures, but inherent characteristics of the material itself.

5. Air pockets are a common occurrence in precast products.

The frequency and size of air pockets are variable and to be expected, especially on vertical surfaces.

6. Concrete corners and edges will chip if not handled according to guidelines. Patch kits are available but may or may not blend and can be variable.

7. There is a level of care and maintenance associated with your

WEIGHT: 1025 lbs TEXTURE: Woodgrain

COLOR:

SEALER:

CUSTOMER APPROVAL x________________________________________

SIDE VIEW ELEVATION

27" 9 1/4" 10"

20"

4"

4"

/2

72"

4"

5"

48" 5"

/2

INSTALLATION REQUIREMENTS::

1. Bench requires epoxy applied to cover bottom of entire leg.

2. Epoxy adhesive should be checked periodically to ensure continued adhesion.

3. Bench is required to be mechanically attached (as shown above)

Threaded inserts in legs for mounting dowels(2 per leg) * (4) 3/4” x 8” coil rods provided per bench for mounting

Solid, smooth center area on leg

4" wide, 3/4" thick steel brackets

(2) per bench, powdercoated Brackets used to attach to bench Bench will be shipped pre-assembled

1" smooth "gaps" between planks on back and seat

OUTDOOR CREATIONS, INC. SCALE: 1” = 18”

OUTDOOR

CREATIONS

INC.

2270 Barney Street Anderson, CA 96007

(530) 365-6106

FAX (530) 365-5129

NOTES:

1. Concrete mix design to include a mixture of Portland Cement, water, coarse and fine aggregates, pure mineral oxide coloring agents (when applicable) to yield a minimum compressive strength of 5000 psi.

2. Final product shall be reinforced with #4 and #5 rebar grid.

3. Product is cast in 1-piece with no assembly required.

4. Hairline cracks may develop over time. These are not structural failures, but inherent characteristics of the material itself.

5. Air pockets are a common occurrence in precast products.

The frequency and size of air pockets are variable and to be expected, especially on vertical surfaces.

6. Concrete corners and edges will chip if not handled according to guidelines. Patch kits are available but may or may not blend and can be variable.

7. There is a level of care and maintenance associated with your

WEIGHT: 750 LBS

TEXTURE: Woodgrain

COLOR:

SEALER:

CUSTOMER APPROVAL x________________________________________

SECTION

Side of legs to be woodgrain texture

Front/back of legs to be smooth texture

ELEVATION

PLAN

17"

4"

24"

1"

4"

4 1/2" 4"

72"

12"

72"

1"

MODEL# 428 - FLAT WOODGRAIN BENCH, 72" x 24" x 18"

Threaded inserts in legs for mounting dowels(1 per leg)

Threaded inserts in legs for mounting dowels(1 per leg)

* (2) 3/4” x 8” coil rods provided per bench for mounting

INSTALLATION REQUIREMENTS::

1. Bench requires epoxy applied to cover bottom of entire leg.

2. Epoxy adhesive should be checked periodically to ensure continued adhesion.

3. Bench must also be mechanically attached.

MODEL #304 GROUP FIRE PIT (4' DIA.) OUTDOOR CREATIONS, INC. SCALE: 1” = 32”

ELEVATION SECTION

PLAN

OUTDOOR

CREATIONS

INC.

2270 Barney Street Anderson, CA 96007

(530) 365-6106

FAX (530) 365-5129

NOTES:

1. Concrete mix design to include a mixture of Portland Cement, water, coarse and fine aggregates, pure mineral oxide coloring agents (when applicable) to yield a minimum compressive strength of 5000 psi.

2. Final product shall be reinforced with #4 and #5 rebar grid.

3. Product is cast in 1-piece with no assembly required.

4. Hairline cracks may develop over time. These are not structural failures, but inherent characteristics of the material itself.

5. Air pockets are a common occurrence in precast products.

The frequency and size of air pockets are variable and to be expected, especially on vertical surfaces.

6. Concrete corners and edges will chip if not handled according to guidelines. Patch kits are available but may or may not blend and can be variable.

7. There is a level of care and maintenance associated with your

WEIGHT: 1350 LBS

COLOR:

SEALER:

6"

18"

46"

34"

48" 32"

1 1/2” radius

34"

32"

46"

48"

48"

18"

6"

* Optional ½ grill (Model # 304G)

- Grill is laser cut from single sheet 3/8” steel

- Grill is attached to casting with (3) ½” x 1” grade 5 bolts

3/16" steel plate fire shield

3/16" steel plate fire shield

CUSTOMER APPROVAL x________________________________________

*Fire rings are designed to accommodate small campfires only.

Large fires, including those that reach a height of 12" or more and/or envelop the entire ring, create excessive heat conditions that may damage the ring. Outdoor Creations Inc is not responsible for damage occuring from conditions beyond normal size camp fires.

���6 "!78 ��������

>?@ABCBADEBFGHIJJ@EBGK>?ALMNLOPPQRST UVWXVYZ[\] ̂_LP̀ aO Hb Jcde\ MdZfg Yf]hi]\j\] Mdi]]

DkDBJDHJ@ F?EBFG>@lm\[[\[ ?Znh Hcn\Ihi]iho >p\]q

>?@ABCBADEBFG>rs YZ[\] ̂_LP̀ aO Hb tuv u vwxyz{ |}}~ v�� wx� y�u�{ {��uzz� �w�w�{� �� �t�{{ ����wxy �tu��{�v� ��u�{ wv v������{� �� �t{ ��� {x� �ux{zv ux� ��� �w�w�{� �ux{zv� ����wxy t{wyt� u���v�v �� � z{�{zv �{��{{x ��|�}� ux� ������ u���{ �t{ �w�{�{� �� �{uxv �� �w{���� vz��v wx vw�{ �ux{zv� ���x� vz��v uzz�� y�u�{ �� �w� �� ��� {uv� �z{uxwxy ux� �w�{ ��wz�wxy�s � �~� � }�� � |~� twyt �w�{��� ux� v�w�{z �{�tuxwv� wv ��xv�����{� {x�w�{z� �� ��|�� �zu�{ v�{{z� �x�{y�uz uvt �zuxy{v u�{ �w{�����{� wx�� ���x� {�y{ �� �{�uwx uvt{v ux� ����w�{ �{wx����{�{x�� �ux{z �{wx����wxy �zu�{v u�{ �w{�����{� wx�� �t{ ���x� {�y{v �� ���t vw�{ �ux{zv ux� ��� �� �{u� �ux{z� �w�{��� wv �w� �{wx����{� �w�t ��|�� �u� v���� �x �t{ �x�{�vw�{ �� ��{�{x� t{u� �u��uy{� �zz {���v{� ���x{�v u�{ ���x�{� �� |�|�}� �u�w�v ux� uzz {�y{ ��xx{��w�xv u�{ {x�w�{z� �{z�{�� �zz��ux�{ ��� ��uwxuy{ vtuzz �{ ����w�{�� s ��u�{ wv ��xv�����{� ���� ���� �wu� ���� v�{{z �u�v ��� v������ tux�z{v ux� |�}� �wu� ���� v�{{z �u�v v�u�{� |�|��� �x �{x�{�v �� ����w�{ �t{ y�u�{ v���u�{ ux� wv �{��ux{x�z� u��u�t{� �� �w�{����s ��u�{ wv ����w�{� �w�t ��� v��v�ux�wuzz� ��xv�����{� ��wz y�w�v �x {u�t {x� ���vw�{ �� �w�{��� v�w�u�z{ ��� ���zw� �v{ �u�{ ���� |��� � |�}� v�{{z �zu� �u� �x�� �w�{ v��wxyv �s ��wzz wv �{��ux{x�z� u��u�t{� u��{� �uv{ wxv�uzzu�w�x �� �{uxv �� u�v�z��{z� �t{�������� �uv{ u��u�t�{x� uzz��wxy ��x�wx���v ��~¡ ���u�w�x �� y�wzz wx {w�t{� �w�{��w�x�s >hc¢[cd[r ��wzz wv v������{� �� u �� £�¤� t{u�� �uzz v�{{z �w�{ �w�t u �{z�{� ���� � |~� � |~� �uv{ �zu�{ �w�t ���� }���}� �wu� t�z{v ��� �{��ux{x� wxv�uzzu�w�x wx ��x��{�{ ����wxy �wx�w�u�{� �� ¥¦�§ wx ���{z x��̈ {�y� ©��}��~ ¦� � �x�z��{v ���� |�}� � �� ª���z� ux�t��v ��� ��x��{�{ ����wxy wxv�uzzu�w�x�s «x�w�{ �xw� wv �wxwvt{� wx twyt �{��{�u���{̈ t{u� �{vwv�ux�̈ x�x���w� �zu�� {xu�{z�s FghiZ¢c]r ��wzz wv v������{� �� u �� £�¤� t{u�� �uzz v�{{z �w�{ �~� z�xy �{vwyx{� �� �{ {��{��{� |�¬ wx�� u ��x��{�{ ����wxy �v�{�w�� �� �{�zu�wxy ¥¦�§ wx ���{z x�� �w�t ¥¦|�§ wx ���{z x��̈ {�y� ©��}��~ ¦|� �s FghiZ¢c]r ��wzz wv ����w�{� �w�t u |~����� � �� ��wzw�� vt{z� �u�{ �� ����{� ® yu� v�{{z� ̄� ���{�̈ u�� °® �� ���{z x��̈ {�y� ©��}��~�° ¦��

±²³́µ ¶·̧¹º»¼ ½¾ ¿ÀÁÂà ÄÁÅÆÇ ÈÆÉÊËÉÃÌÃÉ ÄÁËÉÉÍ ÎÏÐÑ ÒÏÏÓÔÕÖ ×ØÔÖ×Ù ÚØÛØÚÜ ÝÔÙ× ÖÑÞÙØ ÞßàÐÜÙáØÕÙ ÔÕ ÜÚÏÙÜ ßÔØâÒÐÙ ãÑÏá Ù×Ø ÜÙØØÚ ni[\n Zq edi]] mZäÍ åÑÞÙØ ãÚÔæÜ Ðæ ãÏÑ ØÞÜç ÒÚØÞÕÔÕÖ ÞÕß ãÔÑØ mfi][i¢eÍ ÎÔÑØèÏé ÔÜ ÑØÔÕãÏÑÒØß ÝÔÙ× ãÚÞÑØÜ ßÔØâãÏÑáØß i¢hZ qdZ¢h \[e\n Zq ni[\ gc¢\]nÍ êÕÙØÖÑÞÚ ÞÜ× ÑØÙÞÔÕØÑ ãÚÞÕÖØ ÒÏáèÞÙÜ ×ØÞÙ ÝÞÑæÞÖØ ÞÕß æÑØÛØÕÙÜ ÞÜ×ØÜ ãÑÏá ãÞÚÚÔÕÖ qdZl hp\ qid\mZäÍ ëØÔÕãÏÑÒØß èÏÙÙÏá æÑØÛØÕÙÜ ×ØÞÙ ÝÞÑæÞÖØÍ ì×ØãÙâæÑÏÏã èÞÜØ ÞÙÙÞÒ×áØÕÙÍ ÎÐÚÚ íîïð ÑÏÙÞÙÔÏÕ ãÏÑ ßÑÞãÙ ÒÏÕÙÑÏÚÍ ñÐèÚÔÒ ÐÜØâÙçæØ ÖÑÔæÜ Ïã ÒÏÔÚØß ÜÙØØÚ èÞÑ

/01232145267�+8990527�:

;? >@�A=B

>? >? >? <?@A�C=B

>D����E��F���G����F��������G�H����IJ�������������K������

>DL�����H����

�M�������J�������GN��K�O�����=G������H������JH����

<D�B�GJ�K�F��H�J����G���������

�M��������<;��H��������G���������

03-465

ASSISTING WITH or PERFORMING AN INSTALLATION IS DONE COMPLETELY AT YOUR OWN RISK!!

ROCKART, Inc. assumes absolutely NO LIABILITY for any type of damage sustained resulting from following the instructions published within this Installation guide. This includes damage to personal property, any personal injury (whether immediate or delayed-onset), loss of life or limb (whether by accident or consequential).

WE STRONGLY RECOMMEND THAT YOU ALWAYS WEAR PROTECTION WHEN AND WHERE APPROPRIATE!

NEVER TAKE RISKS WITH YOUR HEALTH & WELL-BEING!

CALL FOR A BLUE STAKE BEFORE DIGGING!

03-465 ROCKART® Message Center Kiosk Installation Guide

Before you begin, it is recommended that you review this entire installation guide.

PG 2

Message Center Kiosk Parts List

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Optional Products Recommended by Rockart

PART

NUMBER DESCRIPTION PRICE EACH

03-524

3-piece Aluminum Assembly Fixture (for 48” wide sign panels)— used during installation to maintain spacing between Posts without risking damage to your sign panels. The price (less shipping) will be refunded when you return this Fixture, in good condition, to Rockart. RECOMMENDED Qty: 2

$175.00 Refundable Deposit

( less shipping )

08-1015 Touch Up Paint, Rust Texture, 12 oz. aerosol can 12.00

03-481 Qty. = 2

03-486 Qty. = 1

Part Drawings are not to scale.

Parts List

QTY PART# DESCRIPTION

2 03-481 6x6 x 108” Steel Vertical End Post with 2 sign mount tabs

1 03-486 6x6 x 108” Steel Vertical Center Post with 4 sign mount tabs

Additional Tools & Supplies Necessary for Installation

1) Auger and 12” bit

2) Post hole digging tools

3) Wheelbarrow

4) Cement Mix for 3 holes @

(5 cubic feet/hole)

5) Water

6) Hoe

7) (5) 36” long 2x6 wood planks

8) (2-3) 12’ long 2x4 wood planks

9) (2-4) Cement spikes

10) 1 Bottle jack

11) Framer’s level

12) (3) saw horses

13) 12’ Metal Tape Measure

14) 3/8” Hex Driver or adjustable wrench

Before You Start . . .

Please check to be sure that you have received (from ROCKART) all items listed below.

Customer will also need to provide items listed under Additional Tools & Supplies (page bottom) to complete this installation successfully.

03-524 3 pieces, includes hardware kit #03-918

03-918 12@3/8-16 x .75 hex head bolts, 12 nuts and 12 washers

PG 3

Front View Drawing

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Post #2Post #3 Post #1

Aluminum Assembly Fixture #1

Aluminum Assembly Fixture #2

Slotted Sign Panel Mounting Tabs

Important Notes

• Install the Assembly Fixture on the backside of the Slotted Mounting Tabs (See below)

• The angled flange (at top & bottom edges) should point to the FRONT of the kiosk (See below)

• The Assembly Fixture’s edge should be FLUSH against the vertical post (See below)

• Insert a washer between the Slotted Mounting Tab and a nut (to avoid scratching paint) (See below)

|Fr on t S id e of

K io sk

PG 4

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Message Center Kiosk Hole Digging Guide

55.5 inches 55.5 inches

111 inches

18” Dia.

POST #1 POST #2POST #3

Front Side of Kiosk

Mark the CENTER locations of each post:

1 Using a metal tape measure, position the start of it at the spot on the ground where the center of Post (#3) will be and mark the spot.

2 Measure 111 inches to the right of that spot and mark the ground where the center of Post (#2) will be.

3 Without moving the tape measure, mark the ground for the center of Post #1, at 55.5” (center between the previous two marks).

4 Excavate 9” of dirt around each marked spot, so when completed, there will be 3 holes that are 18” diameter and 30” deep.

Applies to: ANY 6x6, 2-PANEL, STRAIGHT KIOSK USING 48”-Wide ROCKART® SIGN PANELS

CALL FOR A BLUE STAKE BEFORE DIGGING!

Review the diagram below:

Each red dot represents where the CENTER of each vertical post should be located.

The green circle centered around each red dot represents an 18” diameter area that should be excavated to a depth of 30” inches.

If installing the kiosk in a location where the ground is NOT LEVEL, these hole depths may need to be adjusted accordingly.

30” deep

18” Dia.

PG 5

Installation Guide

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

What You Will Need to KNOW... These Instructions Apply to Model(s):

Be sure you have reviewed these related sections:

• Kiosk Parts, Tools & Supplies List , PG 2

• Front View Drawing , PG 3

• Hole Digging Guide, PG 4

• This Installation Guide

• Sign Panel Installation Guide (if your kiosk was purchased with sign panels)

#03-465

PLEASE READ FIRST

ROCKART STRONGLY RECOMMENDS the following for the best results:

• For this size Kiosk, we recommend a 2 to 3 person crew.

• Assembly time takes 1 to 2 hours.

• Check to make sure all tools mentioned at the bottom of page 1 are supplied

• Hardware and small tools will ship to you separately via UPS at the same time your Kiosk(s) ships.

• With regards to left/right designations, instructions are written with the assumption that the reader is facing the front of the Kiosk.

• You will need TWO (2) Aluminum Assembly Fixtures (#03-524) to install this kiosk. NOTE: DO NOT

ATTEMPT TO Use Sign Panels in place of the Assembly Fixture! The fixture maintains correct spac-ing between posts while they are being installed. By using them, you need not worry about damaging your actual sign panels, should something go wrong.

• IMPORTANT: Keep the original Aluminum Assembly Fixture shipping boxes. They are necessary to re-turn the fixture(s) for your deposit refund.

Stage I - Assemble & Install the Kiosk Preparation

1 REVIEW Pages 2 & 3. Get familiarized with the kiosk part names & numbers.

2 DIG HOLES – Using the guide on Page 3.

3 ENSURE all holes are only 30” deep for proper viewing height of kiosk sign panels!

4 ASSEMBLE each of the required Aluminum Assembly Fixture(s) using hardware kit #03-918, containing

3/8-16 hex head bolts, nuts and washers.

Installation

1 POSITION a saw horse approx. 7 feet behind each hole. Lay the top capped end of the center Post #1 (#03-486) across a sawhorse positioned so that the slotted sign panel mounting tabs are pointing left and right (parallel to the ground). The bottom end of the post should be suspended over the center hole in the ground. Likewise, PLACE each end Post #2 and #3 (#03-481) in their respective places, with their slotted tabs pointing towards the center of the installation. (See Fig 1)

2 STAND a 2x6, 36” long plank (on end) into each hole, perpendicular to each of the posts. This acts as a guide and allows the posts to slide into the hole with less resistance and with less dirt falling into the hole. (See Fig 2)

PG 6

Installation Guide

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

3 USE remaining 3/8-16 bolts, nuts and washers from hardware kit #03-918 and follow Important Notes on page 3 to INSTALL each of the Aluminum Assembly Fixtures to the BACKSIDE of the four slotted sign mounting tabs (similar to Fig 3) The 1” bent flange of the assembly fixture should be pointing toward the front side of the kiosk.

ENSURE the vertical edges of the Aluminum Assembly Fixture are flush against the vertical edge of the posts before tightening the bolts. Note: Always place a flat washer next to the sign tab slot before applying a nut (see Fig 4)

4 ASSISTED by 2-3 more able persons, gently RAISE the top ends of the assembled kiosk into place, carefully guiding the posts down into the pre-dug holes (similar to Fig 5)

5 STABILIZE the structure using the user-supplied 12ft long 2x4 wood planks & concrete spikes as need-

ed. Tip: placing several large rocks into the open space around the post will help further stabilize it (similar to Fig 6A & 6B).

6 ENSURE all Assembly Fixtures are flush with the vertical posts and all bolts are tight.

7 USING a framer’s level, VERIFY that each Assembly Fixture is level and that each vertical post is plumb

(similar to Fig 7).

Tip: To help level the structure, vertically stack several pieces of 2x4 or 2x6 wooden planks di-rectly under the assembly fixture (on the side that needs to be elevated). Then place a bottle jack atop the stack of wood planks and extend the jack until it pushes against the 1” angled flange at the bottom of the assembly fixture ... continue extending the jack until the structure is level (similar to Fig 8).

8 FOLLOW the manufacturers instructions to MIX concrete and then POUR into each hole (similar to Fig 9) .

Sit back, relax and ALLOW concrete to set properly.

9 After the concrete has properly set, REMOVE the Aluminum Assembly Fixtures.

The Kiosk structure is complete!

You are now ready for STAGE II - Sign Panel Installation.

Fig 2 Fig 3Fig 1

PG 7

Installation Guide

Model: 03-465 6x6 2-Panel Straight Kiosk w/No Roof (48x48 panels)

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Fig 7

Fig 4

Vertical Post

Front of Kiosk

1” Angled Flange of Assembly FixtureWasher

Hex Head Bolt

Hex Head Nut

Slotted Sign Panel Mounting Tab

Fig 5

Fig 9

Fig 6A

Fig 8

Fig 6B

Don’t forget to return the ALUMINUM ASSEMBLY FIXTURES back to ROCKART.

Follow the directions on the included RMA Form to return-ship undamaged & usable Fixtures back to Rockart, Inc. Use the original shipping boxes, if possible. (No need to return the hardware used to assemble them.) After the fixtures have been received by Rockart, you will receive a refund of the security deposit (less shipping charges).

PG 8

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Message Center Kiosk STAGE II - Sign Panel Install Guide

Installation Note for Fully-Enclosed* Sign Panels:

Before mounting a Fully-Enclosed* Sign Panel to the Kiosk, check the orientation of the removable side rail. Fully-Enclosed sign panel displays will have 3 to 5 bolts embedded within this rail (circled on left) that secure the entire display and when installed, and should be along the right side.

For sign panels that include Routed Text across the header and/or footer, verify that the text is displayed as desired.

How to properly install a VandlGard® tamper-resistant nut:

If your kiosk sign panel included tamper-resistant mounting hardware, the odd-looking nuts are tamper resistant and should be installed as follows:

Start by threading the wide, tapered end of the cone-shaped nut onto the end of the bolt as shown by the green arrow (see top image, left). Twist clock-wise with fingers & thumb, until snug.

Using a hex wrench or pair of pliers, continue to tighten the Hex part of the nut until the hex part breaks off... leaving the conical part behind (see bottom image, left). Discard the hex nut. ... all done!

* A Fully-Enclosed Sign Panel protects the displayed content completely (on every side). These models feature a removable side rail (on either the left or right side), and a protective clear polycarbonate cover that is also removable.

Opening a “fully-enclosed” Sign Panel:

To open a Fully-Enclosed* Sign Panel (to change out the signage) you will need the special YELLOW colored Hex tool (included with fully-enclosed displays) to remove the 3 to 5 bolts along the right side (don’t lose them!). Remove the side rail. Grab the tail-end of the flexible security rod sitting on top of the clear polycarbonate cover, and pull it completely out of the channel through the opening (see image, left).

Slide the clear polycarbonate cover over enough to allow you to grasp it firmly on both left & right sides. Lift it straight up, pushing the top edge deeper into the top channel. Now, pivot the bottom edge of the cover out from the display (i.e., towards yourself). Take note which side was facing out (and when done, return it accordingly).

Place the clear cover in an area that is clean as possible while swapping out content.

When finished, simply follow these steps in reverse order. Don’t forget to RE-INSERT the flexible security rod ! Finally, use the YELLOW hex tool as before to secure the side access rail using the same bolts removed earlier.

Flexible Security Rod

Special Hex tool (#08-619) used to open fully-enclosed sign panels (included)

Important information for ROCKART® Sign Panels and Message Center Kiosks

PG 9

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Message Center Kiosk Sign Panel Install Guide

Vertical Steel Post

Tackboard Sign

Slotted Sign Panel Mounting Tab

Plastic Flat Washer

VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex

2“ Dia. Stainless Steel Fender Washer

2“ Dia. Stainless Steel Fender Washer

Carriage Bolt

Black Nylon Carriage Bolt Adapter

FRONT of Kiosk

Clear Polycarbonate Cover (Optional) Vertical Steel Post

Slotted Sign Panel Mounting Tab

Plastic Flat Washer

VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex

2“ Dia. Stainless Steel Fender Washer

2“ Dia. Stainless Steel Fender Washer

Carriage Bolt

Black Nylon Carriage Bolt Adapter FRONT of Kiosk

Tackboard Sign

Header / Footer

Vertical Steel Post

Ballistic Tack Board Sign

Header / Footer

Header / Footer

Slotted Sign Panel Mounting Tab

Plastic Flat Washer

VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex

2“ Dia. Stainless Steel Fender Washer

2“ Dia. Stainless Steel Fender Washer

Carriage Bolt

Black Nylon Carriage Bolt Adapter FRONT of Kiosk

Tack Board Only #03-901 ASSEMBLY KIT

Header / Footer (Single-Sided) #03-903 ASSEMBLY KIT

Header / Footer (Double-Sided) #03-904 ASSEMBLY KIT

Using included hardware from #03-901, follow the hardware stacking guide (right) to secure each corner of the sign panel to the kiosk.

Using included hardware from #03-903, follow the hardware stacking guide (right) to secure each corner of the sign panel to the kiosk.

Using included hardware from #03-904, follow the hardware stacking guide (right) to secure each corner of the sign panel to the kiosk.

For Single- and Double-sided Sign Panels having 1 mounting hole in each corner

PG 10

Ro ck ar t, In c.

v .2

Ja n1

3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com

Message Center Kiosk Removing Polycarbonate Cover

Removing the Cover

Important! DO NOT REMOVE the 4 Corner Bolts that secure the Sign Panel to the Kiosk!

1 USE the special YELLOW hex wrench (included with your sign panel) to REMOVE the tamper-resistant bolts usually located on the right side of a sign panel (from the Front side of kiosk). Don’t lose these bolts! The nuts are embedded in either the tack-board (for single-sided panels) or in a matching removable side rail on the opposing side (double-sided panels) and should stay in place while the bolts are removed.

Remove bolts marked as “1” (see figure, right).

2 REMOVE the side rail (or rails) of the Sign Panel and set aside.

3 PULL OUT the Flexible PLASTIC ROD inserted into the space above the polycarbonate cover. Don’t lose it! (This important security feature prevents vandals from removing the cover themselves)

4 SLIDE the cover over about an inch, so you can FIRMLY GRASP both sides.

5 LIFT the cover straight up into the top grooved channel then PIVOT the bottom edge towards your body, until it is completely free. Set the cover aside (somewhere clean) so it can be replaced with the same side facing outward. (Remember which side faces out... since UV or Anti-Graffiti films are usually applied to one side only.)

6 SWAP OUT SIGN CONTENT

Replacing the Cover

NOTE: Replace the cover with same side facing out (UV or Anti-Graffiti films are usually applied to one side only).

1 GRASP the left & right sides of the cover, INSERT the top edge fully into the top grooved channel.

2 PIVOT the bottom edge of cover to line up with the bottom grooved channel. Carefully RELEASE it, allowing it to sit in the bottom grooved channel.

3 GENTLY SLIDE the cover left/right (toward the non-removable side rail) until it cannot go any further.

4 RE-INSERT the Flexible PLASTIC ROD into the gap just above the cover itself.

5 Finally, REPLACE the vertical rail(s) and secure with the tamper-resistant bolts using the special YELLOW hex wrench.

Stuff You Need to Know These Instructions Apply to:

• You’ll need the specially-keyed, L-shaped YELLOW hex wrench #08-619 (included with fully-enclosed ROCKART® Sign Panels).

• The tackboard is VERY dense; thumbtacks and push-pins cannot penetrate it. Consider using an industrial staple gun with heavy duty staples.

• Keep the inside of the sign panel as clean as possible: While performing the steps below, avoid placing removed components directly on the ground. Using a tarp or other ground cover is recommended!

ROCKART®

Standard Sign Panels

(Full-sized & Fully-Enclosed Single-or Double-sided Sign Panels)

IF YOU ARE REPLACING A DAMAGED COVER: If there are any protective (opaque) liners applied to either side of a polycarbonate cover REMOVE the protective liner from the cover as soon as possible. If the liner is exposed to sunlight for extended periods, it may be very difficult to remove.

Instructions only for “fully-enclosed” full-sized ROCKART® Sign Panels