11-Spec 4 - Freightliner M2 106 Peterson TL3 - PCN ADD26A.44.pdf

Freightliner M2 106 w/ Peterson TL3 Hardox Grapple 158419, 158416, 158418

Chassis Specifications:

• Freightliner M2 106 Chassis

• Cummins B6.7 260HP engine

• Allision 3500RDS transmission

• High back air suspension driver’s seat

• Passenger seat

• Power windows and door locks

• Expected front axle(s) load : 12000.0 lbs

• Expected rear drive axle(s) load : 21000.0 lbs

• Expected gross vehicle weight capacity: 33000.0 lbs

• 75 MPH road speed limit

• Cruise control speed limit same as road speed limit

• Chelsea 280 Series PTO

• PTO mode engine rpm limit - 1100 rpm

• PTO rpm with cruise set switch - 900 rpm

• PTO rpm with cruise resume switch - 900 rpm

• PTO mode cancel vehicle speed -5 mph

• PTO governor ramp rate -250 rpm per second

• One remote PTO speed

• PTO speed 1 setting - 900 rpm PTO minimum rpm-

• Regen inhibit speed threshold -5 mph

• PTO 1, dash switch, stationary operation

• Tires: 11R22.5

• (2) Threaded stud batteries

• Battery box mounted left-side under frame

• Cummins turbocharged 18.7 CFM air compressor

• White exterior paint

Grapple Body Specification:

• Petersen TL3 w/1828 Hardox Grapple body

• Joystick controls for body/grapple operation

• Model tl3 base loader

• Heavy duty swing motor

• Standard height pedestal

• Grating heat shield (for dual controls only)

• HDHI outrigger strobe

• Standard bucket 60

• Boom-up warning light/audible alarm

• Swing lock (pedestal for boom)

• Hose guards- head & valve bank

• Work lights - (set of 2) (1 each side of boom)

• Toolbox, truck frame mounted under body (add-on)

• HD control box

• Throttle engine kill & horn

• Tandem pump in lieu of single 18 GMP

• Triangle flare kit

• Fire extinguisher, 10lb

• Loader single color PI orange

• Install tow hooks on the rear outside of the right and left frame rails.

• Install cone holders on the right and left frame rail forward of drive wheels.

• Install amber flashers in upper and lower body corner posts.

• Model HDX-1828 Hardox body 1/8" sides, 3/16 floor

• Electric goal post type load covering device

• Standard barn doors for body

• Wire loom for body wiring

• Single strobe mounted on rear of body

• Led type body lights, 15 ea.

• Amber led flashers in rear corner post

• Brush guard for single rear strobe

• ABSI Z245 package

• Work lights - (set of 2) (curbside under body)

• Work lights - (set of 2) (streetside under body)

• Body color: black

THE DEALER IS RESPONSIBLE FOR PROVIDING TITLE, COUNTY TAG AND REGISTRATION. THIS

SHALL INCLUDE THE TEMPORARY TAG, TWO WAY OVERNIGHT SHIPPING OF ALL

DOCUMENTATION AND ANY ASSOCIATED FEES

IN ACCORDANCE WITH HILLSBOROUGH COUNTY FLEET MANAGEMENT POLICY, DEALER IS

RESPONSIBLE FOR ARRANGING OFFLOAD CAPABILITIES FOR THEIR VEHICLES OR EQUIPMENT

BEING DELIVERED.

THE DEALER WILL PROVIDE HILLSBOROUGH COUNTY FLEET MANAGEMENT WITH MINIMUM

QUARTERLY UPDATES ON THE BUILD/ORDER STATUS OF THE EQUIPMENT.

DEALER MUST NOT UTILIZE OEM WIRING FOR EQUIPMENT ADD‐ONS DEALER MUST ABIDE BY

GENERAL PRACTICES COVERED UNDER OEM.

4 Corner LED Requirements

4 Corner LED Lights / Formerly Called Strobes (VENDOR):

Install led directional light #BK7308093 (4 ea) - the color of all 4 LEDs shall be white. One LED is to be installed in each corner of the unit’s front grille and rear bumper sections as shown using red circles in attached pictures.

All 4 bulbs shall be mounted and wired according to manufacturer’s guidelines and be controlled by one toggle switch #ECHRS1032 where LEDs can be activated/deactivated without ignition being on. Toggle switch shall be mounted in center bottom portion of dashboard to prevent accidental activation. All wiring shall be secured in a fashion that prevents chaffing, shorting of circuit, and becoming snagged on any debris while unit is in operation. The complete circuit shall be fuse protected using a #BK782-2023 fuse holder at the battery