10-RERERENCEDOC 24074 PSDMasonRidge BidPermit 20250929 AddendumTWO.pdf

Page 1 Addendum TWO

Project 052401B

DATE:

ADDENDUM NO:

PROJECT NO:

October 3, 2025

Addendum TWO

052401B

PROJECT DESCRIPTION: MSR Building Renovations & Site Improvements

Mason Ridge Elementary, 715 South Mason Rd., Town &

Country, MO 63141

This Addendum is hereby made part of the Contract Documents of the above named Project. It supplements and modifies them as follows:

Specifications:

1. Replace entirely Sections:

Door Hardware Schedule 080671

087100 Door Hardware

2. Replace the following text in Section 081613, Fiberglass Doors paragraph 3.04.D:

“D. Adjust automatic door closer for smooth and consistent activation and operation, as well as manual operation when ADA activation is turned off.”

with the following text:

“D. Adjust automatic door closer for smooth and consistent activation and operation, as well as manual operation when ADA activation is turned off 15 lb maximum pressure to operate.”

Drawings:

1. Replace entirely Sheet C8, Site Details with the attached new Sheet.

END ADDENDUM NUMBER TWO

(This Addendum consists of 20 page)

PN052401B Door Hardware Schedule MSR Building Renovations and Site Improvements 080671 - 1 Mason Ridge Elementary School

SECTION 080671

DOOR HARDWARE SCHEDULE

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Preliminary schedule of door hardware sets for swinging as indicated on drawings.

1.02 RELATED REQUIREMENTS

A. Section 087100 - Door Hardware: Requirements to comply with in coordination with this section.

1.03 REFERENCE STANDARDS

A. BHMA (CPD) - Certified Products Directory.

B. BHMA A156.3 - Exit Devices.

C. BHMA A156.5 - Cylinders and Input Devices for Locks.

D. BHMA A156.13 - Mortise Locks & Latches Series 1000.

E. BHMA A156.18 - Standard for Materials and Finishes.

F. DHI (H&S) - Sequence and Format for the Hardware Schedule.

1.04 PROJECT INFORMATION

A. Project Name: MSR Building Renovations and Site Improvements.

1. Location: Mason Ridge Elementary | Town & Country, MO 63141 and Various Locations District Wide

B. Architect: Bond Architects, Inc

1. Phone Number: 314-863-4994

C. Contractor: To Be Determined.

1.05 SUBMITTALS

A. See Section 013000 - Administrative Requirements, for submittal procedures.

B. Comply with submittal requirements as indicated in Section 087100.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Only manufacturers listed in Section 087100 are considered acceptable.

B. Obtain each type of door hardware as indicated from a single manufacturer and single supplier.

C. Products are listed and certified compliant with specified standards by BHMA (CPD).

D. Manufacturer's Abbreviations: Coordinate with manufacturers listed in Section 087100.

1. BAS / BES - Best Access Systems.

2. HGR / HAG - Hager.

3. HES - HES.

4. IVE - Ives.

5. LCN - LCN.

6. McK - McKinney.

7. NGP - National Guard Products.

8. PEM - Pemko.

9. RIX - Rixson.

10. ROC - Rockwood.

11. SA - Sargent.

12. SCH - Schlage.

13. SEC - Securitron.

14. VD / VON - Von Duprin.

Door Hardware Schedule PN052401B 080671 - 2 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

2.02 DESCRIPTION

A. Door hardware sets provided represent the design intent, they are only a guideline and should not be considered a detailed or complete hardware schedule.

1. Provide door hardware item(s) as required for similar purposes, even when item is not listed for a door in Door Hardware Schedule.

2. Door hardware supplier is responsible for providing proper size and hand of door for products required in accordance with Door Hardware Schedule and as indicated on drawings.

3. Quantities listed are for each Pair (PR) of doors, or for each Single (SGL) door, as indicated in hardware sets.

2.03 LOCK FUNCTION CODES

A. Function Codes for Cylindrical Locks: Complying with BHMA A156.5.

B. Function Codes for Mortise Locks: Complying with BHMA A156.13.

C. Function Codes for Exit Devices: Complying with BHMA A156.3.

2.04 FINISHES

A. Finishes: Complying with BHMA A156.18.

1. Code 626: Satin chromium plated over nickel, with brass or bronze base material (former US equivalent US26D).

PART 3 EXECUTION

3.01 DOOR HARDWARE SCHEDULE

A. Organize listing of door hardware components within each hardware set in compliance with 10- Part scheduling sequence indicated in DHI (H&S), unless otherwise indicated.

3.02 HARDWARE SET # 01.01:

A. For use on Door Number(s): EXD-C1A, EXD-C1D.

B. Provide for each Pair (PR) door(s).

UNITS LOCK ITEM DESCRIPTION FINISH MFR

1 TA2714 4.5X4.5 POE

NRP

Butt Hinge BB Non Removable with POE wires 626 Mck

5 TA2714 4.5X4.5 NRP Butt Hinge BB Non Removable 626 Mck

1 4954 REMOVABLE MULLION 689 VON

2 LD-99EO-XX (length) PANIC HARDWARE 626 VON

1 CD-XP99-L-DT-06 PANIC HARDWARE 626 VON

1 70 IN220 231 BIPS B

EK1 NJ

ELECTRONIC EXIT TRIM US26D SAR

2 AS REQUIRED SFIC KEYED CONST CORE 626 BES

1 AS REQUIRED RIM CYLINDER LESS CORE 626 BES

1 AS REQUIRED PERMANENT CORE NY

DIST. 626 BES

2 4040XP SCUSH TBSRT

1 3/4" SURFACE CLOSER 689 LCN

1 840S X LENGTH AS

REQUIRED DRIP CAP HAG

1 8780NBK PSA MULLION SEAL BK ZER

1 BY FRAME MFR. WEATHER STRIPPING UNK

2 BY DOOR

MANUFACTURER

DOOR SWEEP

MSR Building Renovations and Site Improvements 080671 - 3 Mason Ridge Elementary School

1 412S X LENGTH AS

REQ'D THRESHOLD AL HAG

1 POE-C1500P WIRE HARNESS MCK

1 POE-C306P WIRE HARNESS MCK

1 POE-C306PRJ WIRE HARNESS MCK

2 AS REQUIRED CLOSER TEMPLATING,

BRACKETS, SHOES,

SPACERS, ETC

LCN

1 MG16-2C (WIRING

BOX)

MISC

Mck

C. OPERATIONAL DESCRIPTION:

ACTIVE LEAFRIM EXIT DEVICE. FREE EGRESS AT ALL TIMES BY PRESSING

PUSHBAR.ENTRY BY ELECTRONIC TRIM WITH KEY OVER RIDE. ACCESS CONTROL

SOFTWARE OR PRESENTING AUTHORIZED CREDENTIAL SHALL UNLOCK DOOR

ALLOWING DOOR TO OPEN. DOOR CONTACT AND RX SWITCH BUILT-IN THE PANIC

DEVICEDOGGING BY KEYED CYLINDER LOCKS DOWN THE PUSHBAR SO THE

LATCHBOLT REMAINS RETRACTED AND DOOR FUNCTIONS AS A PUSH/PULL.SELF-

CLOSING. SPRING LOADED STOP INCLUDED. PUSH SIDE MOUNTED.

INACTIVE LEAFRIM EXIT DEVICE. FREE EGRESS AT ALL TIMES BY PRESSING

PUSHBAR. ENTRY BY FIXED LEVER WHEN DEVICE DOGGED DOWN. DOGGING BY

KEYED CYLINDER LOCKS DOWN THE PUSHBAR SO THE LATCHBOLT REMAINS

RETRACTED AND DOOR FUNCTIONS AS A PUSH/PULL.SELF-CLOSING. SPRING

LOADED STOP INCLUDED. PUSH SIDE MOUNTED. REMOVABLE MULLION

3.03 HARDWARE SET # 03.01:

A. For use on Door Number(s): EXD-800.

B. Provide for each Single (SGL) door(s).

UNITS LOCK ITEM DESCRIPTION FINISH MFR

3 TA2714 4.5X4.5 NRP Butt Hinge BB Non Removable 626 Mck

1 LD-XP99-EO PANIC HARDWARE 626 VON

1 4040XP SCUSH TBSRT

1 3/4"

SURFACE CLOSER 689 LCN

1 840S X LENGTH AS

REQUIRED

DRIP CAP HAG

1 BY FRAME MFR. WEATHER STRIPPING

1 BY DOOR

MANUFACTURER DOOR SWEEP

1 412S X LENGTH AS

REQ'D THRESHOLD AL HAG

1 AS REQUIRED

CLOSER TEMPLATING,

BRACKETS, SHOES,

SPACERS, ETC

AL HAG

C. OPERATIONAL DESCRIPTION

RIM EXIT DEVICE. FREE EGRESS AT ALL TIMES BY PRESSING PUSHBAR. EXIT ONLY,

NO EXTERIOR TRIM. SELF-CLOSING. SPRING LOADED STOP INCLUDED. PUSH SIDE

MOUNTED.

3.04 HARDWARE SET # 03.02:

A. For use on Door Number(s): EXD-300A.

080671 - 4 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

B. Provide for each Pair (PR) door(s).

UNITS LOCK ITEM DESCRIPTION FINISH MFR

6 TA2714 4.5X4.5 NRP Butt Hinge BB Non Removable 626 Mck

1 4954 REMOVABLE MULLION 689 VON

2 LD-XP99-EO PANIC HARDWARE 626 VON

2 4040XP SCUSH TBSRT

1 3/4" SURFACE CLOSER 689 LCN

1 840S X LENGTH AS

REQUIRED DRIP CAP HAG

1 8780NBK PSA MULLION SEAL BK ZER

1 BY FRAME MFR. WEATHER STRIPPING UNK

2 BY DOOR

MANUFACTURER

DOOR SWEEP

1 412S X LENGTH AS

REQ'D THRESHOLD AL HAG

2 AS REQUIRED CLOSER TEMPLATING,

BRACKETS, SHOES,

SPACERS, ETC

LCN

C. OPERATIONAL DESCRIPTION:

BOTH LEAVES RIM EXIT DEVICE. FREE EGRESS AT ALL TIMES BY PRESSING

PUSHBAR. EXIT ONLY, NO EXTERIOR TRIM. SELF-CLOSING. SPRING LOADED STOP

INCLUDED. PUSH SIDE MOUNTED. REMOVABLE MULLION

3.05 HARDWARE SET # 03.03:

A. For use on Door Number(s): EXD-300B, EXD-608.

B. Provide for each Pair (PR) door(s).

UNITS LOCK ITEM DESCRIPTION FINISH MFR

6 TA2714 4.5X4.5 NRP Butt Hinge BB Non Removable 628 Mck

1 4954 REMOVABLE MULLION 689 VON

2 LD-99EO-XX(Length) PANIC HARDWARE 626 VON

2 4040XP SCUSH TBSRT

1 3/4" SURFACE CLOSER 689 LCN

1 840S X LENGTH AS

REQUIRED DRIP CAP HAG

1 BY FRAME MFR. WEATHER STRIPPING UNK

2 BY DOOR

MANUFACTURER

DOOR SWEEP

1 412S X LENGTH AS

REQ'D THRESHOLD AL HAG

2 AS REQUIRED CLOSER TEMPLATING,

BRACKETS, SHOES,

SPACERS, ETC

C. OPERATIONAL DESCRIPTION:

MSR Building Renovations and Site Improvements 080671 - 5 Mason Ridge Elementary School

ACTIVE LEAF RIM EXIT DEVICE. FREE EGRESS AT ALL TIMES BY PRESSING

PUSHBAR. ENTRY BY FIXED LEVER AFTER RETRACTING LATCHBOLT WITH KEY.

LEVER ALWAYS FIXED. DOGGING BY KEYED CYLINDER LOCKS DOWN THE PUSHBAR

SO THE LATCHBOLT REMAINS RETRACTED AND DOOR FUNCTIONS AS A PUSH/PULL.

SELF-CLOSING. SPRING LOADED STOP INCLUDED. PUSH SIDE MOUNTED.

INACTIVE LEAF RIM EXIT DEVICE. FREE EGRESS AT ALL TIMES BY PRESSING

PUSHBAR. EXIT ONLY, NO EXTERIOR TRIM.SELF-CLOSING. SPRING LOADED STOP

INCLUDED. PUSH SIDE MOUNTED. REMOVABLE MULLION

END OF SECTIO N

080671 - 6 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

PN052401B Door Hardware MSR Building Renovations and Site Improvements 087100 - 1 Mason Ridge Elementary School

SECTION 087100

DOOR HARDWARE

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Hardware for wood and FRP doors.

B. Hardware for fire-rated doors.

C. Electrically operated and controlled hardware.

D. Low Energy Power Automatic Operators E. Thresholds.

F. Weatherstripping and gasketing.

1.02 RELATED REQUIREMENTS

A. Section 064100 - Architectural Wood Casework: Cabinet hardware.

B. Section 079200 - Joint Sealants: Sealants for setting exterior door thresholds.

C. Section 080671 - Door Hardware Schedule: Schedule of door hardware sets.

D. Section 081113 - Hollow Metal Doors and Frames.

E. Section 081416 - Flush Wood Doors.

F. Section 081613 - Fiberglass Doors.

G. Section 083490 - Tornado-Resistant Assemblies: Tornado doors for storm shelters H. Section 101400 - Signage: Additional signage requirements.

I. Section 284600 - Fire Detection and Alarm: Electrical connection to activate door closers.

1.03 REFERENCE STANDARDS

A. BHMA A156.1 - Standard for Butts and Hinges.

B. BHMA A156.2 - Bored and Preassembled Locks and Latches.

C. BHMA A156.3 - Exit Devices.

D. BHMA A156.4 - Door Closers and Pivots.

E. BHMA A156.5 - Cylinders and Input Devices for Locks.

F. BHMA A156.6 - Standard for Architectural Door Trim.

G. BHMA A156.7 - Template Hinge Dimensions.

H. BHMA A156.8 - Door Controls - Overhead Stops and Holders.

I. BHMA A156.13 - Mortise Locks & Latches Series 1000.

J. BHMA A156.15 - Release Devices - Closer Holder, Electromagnetic and Electromechanical.

K. BHMA A156.16 - Standard for Auxiliary Hardware.

L. BHMA A156.17 - Self Closing Hinges & Pivots.

M. BHMA A156.18 - Standard for Materials and Finishes.

N. BHMA A156.21 - Thresholds.

O. BHMA A156.22 - Standard for Gasketing.

P. BHMA A156.26 - Standard for Continuous Hinges.

Q. BHMA A156.30 - High Security Cylinders.

R. BHMA A156.31 - Electric Strikes and Frame Mounted Actuators.

S. DHI WDHS.3 - Recommended Locations for Architectural Hardware for Flush Wood Doors.

T. NFPA 80 - Standard for Fire Doors and Other Opening Protectives.

Door Hardware PN052401B 087100 - 2 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

U. UL (DIR) - Online Certifications Directory.

V. UL 437 - Standard for Key Locks.

1.04 ADMINISTRATIVE REQUIREMENTS

A. Coordinate the manufacture, fabrication, and installation of products that door hardware is installed on.

B. Furnish templates for door and frame preparation to manufacturers and fabricators of products requiring internal reinforcement for door hardware.

1.05 SUBMITTALS

A. See Section 013000 - Administrative Requirements for submittal procedures.

B. Product Data: Manufacturer's catalog literature for each type of hardware, marked to clearly show products to be furnished for this project, and includes construction details, material descriptions, finishes, and dimensions and profiles of individual components.

C. Shop Drawings - Door Hardware Schedule: Submit detailed listing that includes each item of hardware to be installed on each door. Use door numbering scheme as included in Contract Documents.

1. Prepared by or under supervision of Architectural Hardware Consultant (AHC).

2. Provide complete description for each door listed.

D. Shop Drawings - Electrified Door Hardware: Submit diagrams for power, signal, and control wiring for electrified door hardware that include details of interface with building safety and security systems. Provide elevations and diagrams for each electrified door opening as follows:

1. Prepared by or under supervision of Architectural Hardware Consultant (AHC) and

Electrified Hardware Consultant (EHC).

2. Elevations: Submit front and back elevations of each door opening showing electrified devices with connections installed and an operations narrative describing how opening operates from either side at any given time.

3. Diagrams: Submit point-to-point wiring diagram that shows each device in door opening system with related colored wire connections to each device.

1.06 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with minimum five years of documented experience.

B. Installer Qualifications: Company specializing in performing work of the type specified for commercial door hardware with at least five years of documented experience.

1.07 INSPECTION AND TESTING

A. Submit a written report of the results of functional testing and inspection for fire door assemblies, in compliance with NFPA 80.

1. Written report to be provided to the Owner and be made available to the Authority Having

Jurisdiction (AHJ).

2. Report to include the door number for each fire door assembly, door location, door and frame material, fire rating, and summary of deficiencies.

1.08 DELIVERY, STORAGE, AND HANDLING

A. Package hardware items individually; label and identify each package with door opening code to match door hardware schedule.

1.09 WARRANTY

A. See Section 017800 - Closeout Submittals for additional warranty requirements.

B. Manufacturer's Warranty: Provide warranty against defects in material and workmanship for period indicated. Complete forms in Owner's name and register with manufacturer.

1. Closers: Five years, minimum.

2. Exit Devices: Three years, minimum.

MSR Building Renovations and Site Improvements 087100 - 3 Mason Ridge Elementary School

3. Locksets and Cylinders: Three years, minimum.

4. Other Hardware: Two years, minimum.

PART 2 PRODUCTS

2.01 HINGES

A. Manufacturers:

1. Hager Companies: www.hagerco.com.

2. Models:

a. Interior doors 36" wide and less, standard weight steel:

1) Hager, BB1279.

b. Swing clear at double egress, heavy weight steel:

1) Hager, BB1262.

c. Corrosive area doors 36" wide and less, standard weight stainless steel:

1) Hager, BB1191.

B. Substitutions: Not permitted.

C. Hinges: Comply with BHMA A156.1, Grade 1.

1. Self Closing Hinges: Comply with BHMA A156.17.

2. Butt Hinges: Comply with BHMA A156.1 and BHMA A156.7 for templated hinges.

a. Provide hinge width required to clear surrounding trim.

3. Continuous Hinges: Comply with BHMA A156.26.

4. Provide hinges on every swinging door.

5. Provide five-knuckle full mortise butt hinges unless otherwise indicated.

6. Provide ball-bearing hinges at each door with closer.

7. Provide non-removable pins on exterior outswinging doors.

8. Provide following quantity of butt hinges for each door:

a. Doors up to 60 inches High: Two hinges.

b. Doors From 60 inches High up to 90 inches High: Three hinges.

c. Doors 84 inches High and over: Butt hinges not allowed, use continuous gear type hinge.

d. Doors 36 inches Wide and over: Butt hinges not allowed, use continuous gear type hinge.

2.02 HINGES, CONTINUOUS GEAR TYPE

A. Manufacturers:

1. Assa Abloy- McKinney or Pemko: www.assaabloydss.com.

2. Hager Companies Roton: www.hagerco.com.

3. Models:

a. For new frames:

1) McKinney, MCK-25HD: only use on wired card readers

2) Roton, 780-224HD

b. For retrofits to existing frames:

1) McKinney, MCK-54D: only use on wired card readers

2) Roton, 780-053HD.

4. Substitutions: Not permitted.

2.03 FLUSHBOLTS AND COORDINATORS

A. Manufacturers:

1. Rockwood, an Assa Abloy Group company: www.assaabloydss.com.

2. Hager Companies: www.hagerco.com.

3. Ives, an Allegion brand: www.allegion.com/us.

4. Trimco: www.trimcohardware.com.

5. Models:

a. Automatic at hollow metal door:

087100 - 4 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

1) Ives, FB31P.

2) Rockwood, 2842.

3) Trimco, 3810.

4) Hager 292D

b. Manual at hollow metal door:

1) Ives, FB358.

2) Rockwood, 550.

3) Trimco, 3917.

4) Hager 282D

c. Automatic at wood doors:

1) Ives, FB41P.

2) Rockwood, 2942.

3) Trimco, 3815.

4) Hager 291D

d. Manual at wood doors:

1) Ives, FB457.

2) Rockwood, 557.

3) Trimco, 3913.

4) Hager 283D

e. Dustproof strike at floor bolts:

1) Ives, DP2.

2) Rockwood, 570.

3) Trimco, 3910.

4) Hager 280X.

6. Substitutions: Not permitted.

B. Flush Bolts: Comply with BHMA A156.16, Grade 1.

1. Flush Bolt Throw: 3/4 inch, minimum.

2. Provides extension bolts in leading edge of door, one bolt into floor, one bolt into top of frame.

a. Pairs of Swing Doors: At inactive leaves, provide flush bolts of type as required to comply with code.

3. Provide dustproof floor strike for bolt into floor, except at metal thresholds.

4. Automatic Flush Bolts: Automatically latch upon closing of door; automatic retraction of bolts when active leaf is opened; located on inactive leaf of pair of doors.

2.04 EXIT DEVICES

A. Manufacturers:

1. Von Duprin, an Allegion brand: www.allegion.com/us.

2. Models:

a. Von Duprin, XP99 series, 17 lever type.

3. Substitutions: Not permitted.

B. Exit Devices: Comply with BHMA A156.3, Grade 1.

1. Lever design to match lockset trim.

2. Provide cylinder with cylinder dogging or locking trim.

3. Provide exit devices properly sized for door width and height.

4. Provide strike as recommended by manufacturer for application indicated.

5. Provide less bottom rod (LBR) at scheduled locations to eliminate use of floor mounted strikes.

6. Provide UL (DIR) listed exit device assemblies for fire-rated doors and panic device assemblies for non-fire-rated doors.

7. For electrical options, provide quick connect plug-in pre-wired connectors.

MSR Building Renovations and Site Improvements 087100 - 5 Mason Ridge Elementary School

2.05 ACCESS CONTROL LOCKS

A. POE Powered proximity card reader access control lock with exterior trim plate.

B. Manufacturer - Access Control Lock and Exit Device:

1. Assa Abloy Brands; Sargent: www.assaabloydss.com.

2. Must be provided and installed by a manufacturer's certified integrator.

3. Model: 70 IN220 231 BIPS B EK1 NJ-### hardwired application.

a. ### = hand:

1) RHR is right hand reversed.

2) LHR is left hand reversed.

b. Coordinate wiring connection for access control device installed from each device location back to the data panel in the nearest MDF or IDF room.

1) Final connections at patch panel to be provided by the Owner.

c. Access Control programming is to be provided by the Owner.

C. Manufacturer - Exterior Trim

2.06 ELECTRIC STRIKES

A. Manufacturers:

1. HES; an Assa Abloy Group company: www.assaabloydss.com.

2. Models:

a. For cylindrical locksets:

1) HES, 1006.

b. For rim exit device:

1) HES, 9600.

3. Substitutions: Not permitted.

B. Electric Strikes: Comply with BHMA A156.31, Grade 1.

1. Provide UL (DIR) listed burglary-resistant electric strike; style to suit locks.

2. Provide non-handed 24 VDC electric strike suitable for door frame material and scheduled lock configuration.

3. Provide field selectable Fail Safe/Fail Secure modes.

4. Provide transformer and rectifier as necessary for complete installation.

5. Connect electric strikes into fire alarm where non-rated doors are scheduled to release with fire or sprinkler alarm condition.

2.07 LOCK CYLINDERS

A. Manufacturers:

1. Best Access Systems, division of Stanley Access Technologies LLC:

www.bestaccess.com.

2. Substitutions: Not permitted.

B. Lock Cylinders: Provide key access on outside of each lock, unless otherwise indicated.

1. Provide standard type cylinders, Grade 1, with seven-pin core in compliance with BHMA

A156.5 at locations indicated.

2. Provide high security mechanical type cylinders, Grade 1, with seven-pin core in compliance with BHMA A156.30 or UL 437 at locations indicated.

3. Provide cylinders from same manufacturer as locking device.

4. Provide cams and/or tailpieces as required for locking devices.

5. Within specific Door Sections, when provisions for lock cylinder are being referenced to this Section, provide specified lock cylinder and keyed to building keying system, unless otherwise indicated.

6. Provide exit only on exterior doors unless scheduled otherwise.

2.08 CYLINDRICAL LOCKS

A. Manufacturers:

087100 - 6 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

1. Best Access Systems, division of Stanley Access Technologies LLC:

www.bestaccess.com.

2. Model: Series 9K37-[Function]-14LS3626

3. Substitutions: Not permitted.

B. Cylindrical Locks (Bored): Comply with BHMA A156.2, Grade 1, 4000 Series.

1. Bored Hole: 2-1/8 inch diameter.

2. Latchbolt Throw: 1/2 inch, minimum.

3. Backset: 2-3/4 inch unless otherwise indicated.

4. Strikes: Provide manufacturer's standard strike for each latchset or lockset with strike box and curved lip extending to protect frame in compliance with indicated requirements.

a. Finish: To match lock or latch.

5. Provide a lock for each door, unless otherwise indicated that lock is not required.

6. Provide an intruder lockset for swinging door where hardware set is not indicated.

7. Trim: Provide lever handle or pull trim on outside of each lock, unless otherwise indicated.

2.09 MORTISE LOCKS

A. Manufacturers:

1. Best Access Systems, division of Stanley Access Technologies LLC; [Series 45H7- Function -14S626- [Door Hand]-LC.]: www.bestaccess.com.

2. Substitutions: Not permitted.

B. Mortise Locks: Comply with BHMA A156.13, Grade 1, Security, 1000 Series.

1. Latchbolt Throw: 3/4 inch, minimum.

2. Deadbolt Throw: 1 inch, minimum.

3. Backset: 2-3/4 inch unless otherwise indicated.

4. Strikes: Provide manufacturer's standard strike for each latchset or lockset with strike box and curved lip extending to protect frame in compliance with indicated requirements.

a. Finish: To match lock or latch.

2.10 DOOR PULLS AND PUSH PLATES

A. Manufacturers:

1. Rockwood or McKinney; an Assa Abloy Group company: www.assaabloydss.com.

2. Hager Companies: www.hagerco.com.

3. Trimco: www.trimcohardware.com.

4. Models:

a. Push Plate:

1) McKinney, P054.

2) Rockwood, 70E.

3) Trimco, 1001-9

4) Hager 30S

b. Pull Plate:

1) McKinney, DP803

2) Rockwood, 111 x 70C

3) Trimco, 1018-3B

4) Hager 33G

5. Substitutions: Not permitted.

B. Door Pulls and Push Plates: Comply with BHMA A156.6.

1. Pull Type: Straight, unless otherwise indicated.

2. Push Plate Type: Flat, with square corners, unless otherwise indicated.

a. Edges: Beveled, unless otherwise indicated.

3. Material: Stainless steel, unless otherwise indicated.

4. Provide door pulls and push plates on doors without a lockset, latchset, exit device, or auxiliary lock unless otherwise indicated.

5. On solid doors, provide matching door pull and push plate on opposite faces.

MSR Building Renovations and Site Improvements 087100 - 7 Mason Ridge Elementary School

2.11 COORDINATORS

A. Manufacturers:

1. Ives, an Allegion brand: www.allegion.com/us.

2. Trimco: www.trimcohardware.com.

3. Hager Companies; www.hagerco.com.

4. Models:

a. Ives, CORG

b. Trimco, 3093

c. Hager 298D

5. Substitutions: Not permitted.

B. Coordinators: Provide on doors having closers and self-latching or automatic flush bolts to ensure that inactive door leaf closes before active door leaf.

1. Type: Bar, unless otherwise indicated.

2. Material: Stainless steel, unless otherwise indicated.

3. Ensure that coordination of other door hardware affected by placement of coordinators and carry bar is applied properly for completely operable installation.

2.12 CLOSERS

A. Manufacturers; Surface Mounted:

1. Norton; an Assa Abloy Group company: www.assaabloydss.com.

2. LCN, an Allegion brand: www.allegion.com/us/#sle.

3. Models:

a. Interior doors with multi-size tri-style packaging:

1) Norton, 7500

2) LCN, 4040XP

b. Exterior doors with heavy duty non-hold open parallel arm with spring-stop:

1) Norton, 7500 CPS

2) LCN, 4040XP-CUSH

4. Substitutions: Not permitted.

B. Closers: Comply with BHMA A156.4, Grade 1.

1. Type: Surface mounted to door.

2. Provide door closer on each exterior door.

3. Provide door closer on each fire-rated and smoke-rated door.

a. Spring hinges are not an acceptable self-closing device, unless otherwise indicated.

4. Where an overlapping astragal is included on pairs of swinging doors, provide coordinator to ensure door leaves close in proper order.

5. At corridor entry doors, mount closer on room side of door.

6. At outswinging exterior doors, mount closer on interior side of door.

2.13 LOW ENERGY POWER AUTOMATIC OPERATORS

A. Electrified Atomatic Operators: ADA compliant type.

B. Provide wireless wall mounted actuators by same manufacturer.

C. Provide weather resistant actuators for exterior locations.

D. Operator motor voltage shall be 120 VAC.

E. Provide extended cover over operator at double door openings.

F. Provide ADA accessible symbols engraved on actuators and stickers on doors in accordance with ANSI A-117.1.

G. Manufacturers:

1. Assa Abloy: www.assaabloy.com

2. Models:

a. Assa Abloy, Besam SW200i.

087100 - 8 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

3. Substitutions: Not permitted.

2.14 OVERHEAD STOPS AND HOLDERS

A. Manufacturers:

1. Rixson or Sargent; an Assa Abloy Group company: www.assaabloydss.com/#sle.

2. Glynn-Johnson, an Allegion brand: www.allegion.com/us/#sle.

3. Hager Companies: www.hagerco.com.

4. Models:

a. Heavy duty surface:

1) Rixson, 9.

2) Sargent, 590.

3) Glynn-Johnson, 90.

4) Hager 70 Series SRF

b. Heavy duty concealed:

1) Rixson, 1.

2) Sargent, 690.

3) Glynn-Johnson, 100.

4) Hager 70 Series CON

5. Substitutions: Not permitted.

B. Overhead Stops and Holders (Door Checks): Comply with BHMA A156.8, Grade 1.

1. Provide stop for every swinging door, unless otherwise indicated.

2. Stop is not required if positive stop feature is specified for door closer; positive stop feature of door closer is not an acceptable substitute for a stop, unless otherwise indicated.

2.15 KICK PLATES

A. Manufacturers:

1. Trimco: www.trimcohardware.com.

2. McKinney or Rockwood an Assa Abloy Company: www.assaabloydss.com

3. Hager Companies: www.hagerco.com

4. Models:

a. McKinney, KP50.

b. Rockwood, K1050.

c. Hager 194S

d. Trimco, K0050.

5. Substitutions: Not permitted.

B. Kick Plates: Provide along bottom edge of push side of every door with closer, except aluminum storefront and glass entry doors, unless otherwise indicated.

1. Thickness: 0.050 inch minimum.

2. Height: 10 inches unless otherwise indicated.

3. Width:

a. Single doors: 1-1/2 inch less than door width on frame stop face and 1 inch less than door width on opposite face.

b. Double doors: 1 inch less than door width on both faces of each door.

4. Bevel all four edges and countersink holes for fasteners.

5. Provide UL listed kickplates where required on fire-rated doors.

2.16 DOOR HOLDERS

A. Manufacturers:

1. McKinney or Rockwood; an Assa Abloy Group company: www.assaabloydss.com/#sle.

2. Hager Companies: www.hagerco.com/#sle.

3. Glynn-Johnson, an Allegion brand: www/allegion.com,/us.

4. Models:

MSR Building Renovations and Site Improvements 087100 - 9 Mason Ridge Elementary School

5. Substitutions: See Section 016000 - Product Requirements.

B. Door Holders: Comply with BHMA A156.16, Grade 1.

1. Type: Lever, or kick down stop, with rubber bumper at bottom end.

2. Material: Aluminum.

2.17 ELECTROMAGNETIC DOOR HOLDERS

A. Manufacturers:

1. Rixson; an Assa Abloy Group company: www.assaabloydss.com.

2. Hager Companies: www.hagerco.com.

3. Models:

4. Substitutions: See Section 016000 - Product Requirements.

B. Electromagnetic Door Holders: Comply with BHMA A156.15.

1. Type: Wall mounted, single unit, standard duty, with strike plate attached to door.

2. Holding Force, Standard Duty: 40 lbs-force, minimum.

3. Voltage: 12 VDC, and provide power supplies by same manufacturer as holders.

4. Fail safe; door released to close automatically when electrical current is interrupted.

5. Provide interface with fire detectors and fire-alarm system for fire-rated door assemblies.

2.18 WALL STOPS

A. Manufacturers:

1. Rockwood or McKinney; an Assa Abloy Group company: www.assaabloydss.com.

2. Hager Companies: www.hagerco.com.

3. Trimco: www.trimcohardware.com.

4. Ives, an Allegion brand: www.allegion.com/us.

5. Models:

a. Wall Stop:

1) McKinney, WS04.

2) Rockwood, 403.

3) Hager, 232W

4) Trimco, 1276CCS.

5) Ives, WS402CCV.

6. Substitutions: See Section 016000 - Product Requirements.

B. Wall Stops: Comply with BHMA A156.16, Grade 1 and Resilient Material Retention Test as described in this standard.

1. Provide wall stops to prevent damage to wall surface upon opening door.

2. Type: Bumper, concave, wall stop.

3. Material: Stainless steel housing with rubber insert.

2.19 ASTRAGALS

A. Manufacturers:

1. Pemko; an Assa Abloy Group company: www.assaabloydss.com.

2. Hager Companies: www.hagerco.com.

3. National Guard Products, Inc: www.ngpinc.com.

4. Substitutions: See Section 016000 - Product Requirements.

B. Astragals: Comply with BHMA A156.22.

1. Type: Split, two parts, and with sealing gasket.

2. Material: Stainless steel.

3. Provide non-corroding fasteners at exterior locations.

2.20 THRESHOLDS

A. Manufacturers:

1. Pemko or McKinney; an Assa Abloy Group company: www.assaabloydss.com.

2. National Guard Products, Inc: www.ngpinc.com.

087100 - 10 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

3. Models:

4. Substitutions: See Section 016000 - Product Requirements.

B. Thresholds: Comply with BHMA A156.21.

1. Provide threshold at each exterior door, unless otherwise indicated.

2. Type: Flat surface.

3. Material: Aluminum.

4. Threshold Surface: Fluted horizontal grooves across full width.

5. Field cut threshold to profile of frame and width of door sill for tight fit.

6. Provide non-corroding fasteners at exterior locations.

2.21 WEATHERSTRIPPING AND GASKETING

A. Manufacturers:

1. Pemko or McKinney; an Assa Abloy Group company: www.assaabloydss.com.

2. Hager Companies: www.hagerco.com/#sle.

3. National Guard Products, Inc: www.ngpinc.com/#sle.

4. Gasketing: Weather type

a. Models:

1) Door bottom sweeps:

(a) McKinney, MCK358CN.

(b) National Guard, 202NA.

(c) Pemko, 368CN.

2) Frame gasket:

(a) Hager, 891SV-DBA

(b) McKinney, MCK2891APK.

(c) National Guard, 700 NA.

(d) Pemko, 2891APK.

5. Substitutions: See Section 016000 - Product Requirements.

B. Weatherstripping and Gasketing: Comply with BHMA A156.22.

1. Head and Jamb Type: Adjustable.

2. Door Sweep Type: Encased in retainer.

3. Material: Aluminum, with brush weatherstripping.

4. Provide frame-applied intumescent gasketing on wood doors that are labeled as smoke and draft control doors (Indicated as "S" on Drawings), unless otherwise indicated.

5. See Section 08 1416 when wood door to frame sealing system is applied by door manufacturer.

6. Provide weatherstripping on each exterior door at head, jambs, and meeting stiles of door pairs, unless otherwise indicated.

7. Provide door bottom sweep on each exterior door, unless otherwise indicated.

8. Provide sound-rated gasketing and automatic door bottom on doors indicated as "Sound-

Rated", "Acoustical", or with "Sound Transmission Class (STC) rating"; fabricate as continuous gasketing, do not cut or notch gasketing material.

2.22 SIGNAGE

A. See Section 101400 for additional signage requirements.

2.23 SILENCERS

A. Manufacturers:

1. Ives, an Allegion brand: www.allegion.com/us.

2. Rockwood; an Assa Abloy Group company: www.assaabloydss.com.

3. Substitutions: See Section 016000 - Product Requirements.

B. Silencers: Provide at equal locations on door frame to mute sound of door's impact upon closing.

1. Single Door: Provide three on strike jamb of frame.

MSR Building Renovations and Site Improvements 087100 - 11 Mason Ridge Elementary School

2. Pair of Doors: Provide two on head of frame, one for each door at latch side.

3. Material: Rubber, gray color.

2.24 FINISHES

A. Finishes: Provide door hardware of same finish, unless otherwise indicated.

1. Primary Finish: 626; satin chromium plated over nickel, with brass or bronze base material (former US equivalent US26D); BHMA A156.18.

2. Secondary Finish: as follows:; BHMA A156.18.

a. For exit devices only, finish is to be US28.

b. For continuous gear hinges, finish is to be dark bronze anodized US20 for interior doors and exterior doors with dark bronze frames or US28 for exterior doors with clear anodized aluminum frames.

3. Exceptions:

a. Where base material metal is specified to be different, provide finish that is an equivalent appearance in accordance with BHMA A156.18.

b. Hinges for Fire-Rated Doors: Steel base material with painted finish, in compliance with NFPA 80.

PART 3 EXECUTION

3.01 EXAMINATION

A. Verify that doors and frames are ready to receive this work; labeled, fire-rated doors and frames are properly installed, and dimensions are as indicated on shop drawings.

3.02 INSTALLATION

A. Install hardware in accordance with manufacturer's instructions and applicable codes.

B. Install hardware on fire-rated doors and frames in accordance with applicable codes and NFPA

80.

C. Use templates provided by hardware item manufacturer.

D. Do not install surface mounted items until application of finishes to substrate are fully completed.

E. Door Hardware Mounting Heights: Distance from finished floor to center line of hardware item.

unless otherwise noted in the Schedule:.

1. For Wood Doors: Install in compliance with DHI WDHS.3 recommendations.

2. For FRP doors: Comply with DHI "Recommended Locations for Architectural Hardware for Steel Doors and Frames" or as recommended by the manufacturer.

F. Set exterior door thresholds with full-width bead of elastomeric sealant at each point of contact with floor providing a continuous weather seal; anchor thresholds with stainless steel countersunk screws.

3.03 FIELD QUALITY CONTROL

A. Perform field inspection and testing under provisions of Section 014000 - Quality

Requirements.

B. Inspection and Testing

1. Provide functional testing and inspection of fire door assemblies by a qualified person in accordance with NFPA 80.

2. Schedule fire door assembly inspection within 90 days of Substantial Completion of the Project.

3. Submit a signed, written final report as specified in Paragraph 1.07.A.

4. Correct all deficiencies and schedule a reinspection of fire door assemblies noted as deficient on the inspection report.

C. Provide an Architectural Hardware Consultant (AHC) to inspect installation and certify that hardware and installation has been furnished and installed in accordance with manufacturer's instructions and as specified.

087100 - 12 MSR Building Renovations and Site Improvements

Mason Ridge Elementary School

3.04 ADJUSTING

A. Adjust work under provisions of Section 017000 - Execution and Closeout Requirements.

B. Adjust hardware for smooth operation.

C. Adjust gasketing for complete, continuous seal; replace if unable to make complete seal.

3.05 CLEANING

A. Clean finished hardware in accordance with manufacturer's written instructions after final adjustments have been made.

B. Clean adjacent surfaces soiled by hardware installation.

C. Replace items that cannot be cleaned to manufacturer's level of finish quality at no additional cost.

D. See Section 017419 - Construction Waste Management and Disposal for additional requirements.

3.06 PROTECTION

A. Protect finished Work under provisions of Section 017000 - Execution and Closeout Requirements.

B. Do not permit adjacent work to damage hardware or finish.

END OF SECTION

.5

S C

A

LE

'-0

.2

.5

S C

A

LE

-1 /2

'-0

.5

S C

A

LE

'-0

S C

A

LE

/4

'-0

S C

A

LE

/2

'-0

S C

A

LE

/4

'-0

S C

A

LE

/8

'-0

S C

A

LE

/1

'-0

Project No:

DATE:

222 SOUTH CENTRAL AVE.

SUITE# 501

ST. LOUIS, MO 63105

TEL: 314.863.4994

FAX: 314.863.4996

www.bondarchitectsinc.com

Bond Architects, Inc.

Missouri State Certificate of Authority #

2009027409

The Professional Architects seal affixed to this sheet applies only to the material and items shown on this sheet. All drawings, instruments or other documents not exhibiting this seal shall not be considered prepared by this architect, and this architect expressly disclaims any and all responsibility for such plan, drawings or documents not exhibiting this seal.

This drawing and the details on it are the sole property of the architect and may be used for this specific project only. It shall not be loaned, copied or reproduced, in whole or in part, or for any other purpose or project without the written consent of the Architect.

Copyright © 2025 by Bond Architects, Inc.

2/

/2

4:

:3

P

M

07/10/25

M as on R id ge

E le m en ta ry

S ch oo l

So ut h M as on

R d.

, T ow n

C ou nt ry

, M O

Pa rk w ay P

N

B

Bu ild in g

R en ov at io ns

S ite Im pr ov em en ts

24074

CEDC

Civil Engineer Consultant Project #2576 Certificate of Authority #2003004674 10820 Sunset Office Drive, Suite 200 St. Louis, MO 63127

314.729.1400 tel

P ar kw ay

S ch oo l D is tr ic t

N . W oo ds

M ill

R d.

, C he st er fie ld

, M O

4.

5.

te l

CD Set

Revisions

No. Description Date

MSD BASE MAP: 19P

MSD PROJECT NUMBER: 25MSD-00141

ST

ATE OF M I SSOUR I

REG ISTERED PROFESS IONAL ENG

IN

EE

R

BRANDON

ASHER HARP

NUMBER

E-28650

001 Addendum 001 09/29/25 002 Addendum 002 10/03/25

C8

Site Details

PATCHING ASPHALT

TRENCH/PAVEMENT

TYPICAL PARKING STALLS

BARRIER CURBING DETAIL

ASPHALT CURBING DETAIL

6/4/2 ASPHALT PAVEMENT (DRIVE AISLES)

6/3 ASPHALT PAVEMENT

(WALKING TRACKS) CONCRETE SIDEWALK

CONCRETE EQUIPMENT/

DUMPSTER PAD

CONCRETE CURB SECTION

COMBINED CURB/SIDEWALK SECTION

(MONOLITHIC SIDEWALK & CURB)

CURB RAMP

CONCRETE EXPANSION JOINT

CONCRETE CONTRACTION JOINT

(ON-SITE USE ONLY)

(ON-SITE USE ONLY)

) EXISTING

FOUNDATION

5'-0" TYP.

Refer to handrail detail

Notes:

1. Treads are 2.5 ft. wide and risers are 6-in. high

2. Refer to architectural drawing for handrail detail.

CONCRETE STEP HANDRAIL DETAILS

HANDRAIL AT END

OF STAIRS

STANDARD RAILING

ELEVATIONEND VIEW

HANDRAIL AT STAIRS

ELEVATIONEND VIEW