10 14 00.10.pdf

Ti nker AFB, OK TAFB Techni cal Spr ci f i cat i ons 2019

SECTI ON 10 14 00. 10

EXTERI OR SI GNAGE

PART 1 GENERAL

1. 1 REFERENCES

The publ i cat i ons l i s t ed bel ow f or m a par t of t hi s speci f i cat i on t o t he ext ent r ef er enced. The publ i cat i ons ar e r ef er r ed t o wi t hi n t he t ext by t he basi c desi gnat i on onl y.

ALUMI NUM ASSOCI ATI ON ( AA)

AA DAF45 ( 2003; Reaf f i r med 2009) Desi gnat i on Syst em f or Al umi num Fi ni shes

AMERI CAN NATI ONAL STANDARDS I NSTI TUTE ( ANSI )

ANSI Z97. 1 ( 2015) Saf et y Gl azi ng Mat er i al s Used i n Bui l di ngs - Saf et y Per f or mance Speci f i cat i ons and Met hods of Test

AMERI CAN WELDI NG SOCI ETY ( AWS)

AWS C1. 1M/ C1. 1 ( 2012) Recommended Pr act i ces f or Resi st ance Wel di ng

AWS D1. 1/ D1. 1M ( 2015; Er r at a 1 2015; Er r at a 2 2016) St r uct ur al Wel di ng Code - St eel

AWS D1. 2/ D1. 2M ( 2014) St r uct ur al Wel di ng Code - Al umi num

ASTM I NTERNATI ONAL ( ASTM)

ASTM A1011/ A1011M ( 2015) St andar d Speci f i cat i on f or St eel , Sheet , and St r i p, Hot - Rol l ed, Car bon, St r uct ur al , Hi gh- St r engt h Low- Al l oy and Hi gh- St r engt h Low- Al l oy wi t h I mpr oved For mabi l i t y and Ul t r a- Hi gh St r engt h

ASTM A123/ A123M ( 2013) St andar d Speci f i cat i on f or Zi nc ( Hot - Di p Gal vani zed) Coat i ngs on I r on and St eel Pr oduct s

ASTM A36/ A36M ( 2014) St andar d Speci f i cat i on f or Car bon St r uct ur al St eel

ASTM A653/ A653M ( 2015; E 2016) St andar d Speci f i cat i on f or St eel Sheet , Zi nc- Coat ed ( Gal vani zed) or Zi nc- I r on Al l oy- Coat ed ( Gal vanneal ed) by t he Hot - Di p Pr ocess

ASTM A924/ A924M ( 2016a) St andar d Speci f i cat i on f or Gener al Requi r ement s f or St eel Sheet , Met al l i c- Coat ed by t he Hot - Di p Pr ocess

Apr i l 2019 Page 1 SECTI ON 10 14 00. 10

ASTM B108/ B108M ( 2015) St andar d Speci f i cat i on f or Al umi num- Al l oy Per manent Mol d Cast i ngs

ASTM B209 ( 2014) St andar d Speci f i cat i on f or Al umi num and Al umi num- Al l oy Sheet and Pl at e

ASTM B209M ( 2014) St andar d Speci f i cat i on f or Al umi num and Al umi num- Al l oy Sheet and Pl at e ( Met r i c)

ASTM B221 ( 2014) St andar d Speci f i cat i on f or Al umi num and Al umi num- Al l oy Ext r uded Bar s, Rods, Wi r e, Pr of i l es, and Tubes

ASTM B221M ( 2013) St andar d Speci f i cat i on f or Al umi num and Al umi num- Al l oy Ext r uded Bar s, Rods, Wi r e, Pr of i l es, and Tubes ( Met r i c)

ASTM B26/ B26M ( 2014; E 2015) St andar d Speci f i cat i on f or Al umi num- Al l oy Sand Cast i ngs

ASTM B62 ( 2015) St andar d Speci f i cat i on f or Composi t i on Br onze or Ounce Met al Cast i ngs

ASTM C1036 ( 2016) St andar d Speci f i cat i on f or Fl at Glass

ASTM D3841 ( 2016) St andar d Speci f i cat i on f or Gl ass Fi ber - Rei nf or ced Pol yest er Pl ast i c Panel s

ASTM E84 ( 2016) St andar d Test Met hod f or Sur f ace Bur ni ng Char act er i st i cs of Bui l di ng Materials

NATI ONAL ASSOCI ATI ON OF ARCHI TECTURAL METAL MANUFACTURERS ( NAAMM)

NAAMM AMP 500 ( 2006) Met al Fi ni shes Manual

NATI ONAL FI RE PROTECTI ON ASSOCI ATI ON ( NFPA)

NFPA 70 ( 2017) Nat i onal El ect r i cal Code

SOCI ETY OF AUTOMOTI VE ENGI NEERS I NTERNATI ONAL ( SAE)

SAE AMS3611 ( 2011; Rev E; St abi l i zed ( S) 2011) Pl ast i c Sheet , Pol ycar bonat e Gener al Pur pose

1. 2 GENERAL REQUI REMENTS

Al l ext er i or s i gnage shal l be pr ovi ded by a s i ngl e manuf act ur er . Ext er i or s i gnage shal l be of t he desi gn, det ai l , s i zes, t ypes, and message cont ent shown on t he dr awi ngs, shal l conf or m t o t he r equi r ement s speci f i ed, and shal l be pr ovi ded at t he l ocat i ons i ndi cat ed. Submi t ext er i or s i gnage schedul e i n el ect r oni c medi a wi t h spr ead sheet f or mat . Spr ead sheet shal l i ncl ude si gn l ocat i on, s i gn t ype, and message. Si gns shal l be compl et e wi t h l et t er i ng, f r ami ng as det ai l ed, and r el at ed component s f or a compl et e i nst al l at i on. Each sampl e shal l consi st of a compl et e s i gn panel wi t h l et t er s and symbol s. Sampl es may be i nst al l ed i n t he wor k, pr ovi ded each sampl e i s i dent i f i ed and l ocat i on r ecor ded. Submi t t hr ee col or sampl es

Apr i l 2019 Page 2 SECTI ON 10 14 00. 10 f or each mat er i al r equi r i ng col or and 12 i nch squar e sampl e of s i gn f ace color.

1. 2. 1 Wi nd Load Requi r ement s

Ext er i or s i gnage shal l be desi gned t o wi t hst and 120 mph wi ndl oad. Submi t desi gn anal ysi s and suppor t i ng cal cul at i ons per f or med i n suppor t of speci f i ed s i gnage.

1. 2. 2 Char act er Pr opor t i ons and Hei ght s

Let t er s and number s on i ndi cat ed si gns f or handi capped- accessi bl e bui l di ngs shal l have a wi dt h- t o- hei ght r at i o bet ween 3: 5 and 1: 1 and a st r oke- wi dt h- t o- hei ght r at i o bet ween 1: 5 and 1: 10. Char act er s and number s on i ndi cat ed si gns shal l be s i zed accor di ng t o t he v i ewi ng di st ance f r om whi ch t hey ar e t o be r ead. The mi ni mum hei ght i s measur ed usi ng an upper case l et t er " X" . Lower case char act er s ar e per mi t t ed.

1. 3 SUSTAI NABI LI TY REPORTI NG

Mat er i al s i n t hi s t echni cal speci f i cat i on may cont r i but e t owar ds cont r act compl i ance wi t h sust ai nabi l i t y r equi r ement s. See Sect i on 01 33 29 SUSTAI NABI LI TY REPORTI NG f or pr oj ect cer t i f i cat i on of r ecycl ed cont ent and document at i on r equi r ement s.

1. 4 SUBMITTALS

Gover nment appr oval i s r equi r ed f or submi t t al s wi t h a " G" desi gnat i on;

submi t t al s not havi ng a " G" desi gnat i on ar e f or Cont r act or Qual i t y Cont r ol appr oval . Submi t t he f ol l owi ng i n accor dance wi t h Sect i on 01 33 00

SUBMI TTAL PROCEDURES:

SD- 02 Shop Dr awi ngs

Appr oved Det ai l Dr awi ngs; G

SD- 03 Pr oduct Dat a

Modul ar Ext er i or Si gnage Syst em Installation Ext er i or Si gnage; G Wi nd Load Requi r ement s

SD- 04 Sampl es

Ext er i or Si gnage; G

SD- 10 Oper at i on and Mai nt enance Dat a

Pr ot ect i on and Cl eani ng; G

1. 5 QUALIFICATIONS

Si gns, pl aques, and di mensi onal l et t er s shal l be t he st andar d pr oduct of a manuf act ur er r egul ar l y engaged i n t he manuf act ur e of t he pr oduct s. I t ems of equi pment shal l essent i al l y dupl i cat e equi pment t hat has been i n sat i sf act or y use at l east 2 year s pr i or t o bi d openi ng.

Apr i l 2019 Page 3 SECTI ON 10 14 00. 10

1. 6 DELI VERY AND STORAGE

Mat er i al s shal l be wr apped f or shi pment and st or age, del i ver ed t o t he j obsi t e i n manuf act ur er ' s or i gi nal packagi ng, and st or ed i n a c l ean, dr y ar ea i n accor dance wi t h manuf act ur er ' s i nst r uct i ons.

1. 7 WARRANTY

Manuf act ur er ' s st andar d per f or mance guar ant ees or war r ant i es t hat ext end beyond a one year per i od shal l be pr ovi ded.

1. 8 EXTRA STOCK

Pr ovi de t wo ext r a i nt er changeabl e message panel s and ext r a st ock of t he f ol l owi ng: f our message bar s of each col or and si ze f or s i gn t ypes pr ovi ded. Four set s of pr essur e- sensi t i ve l et t er s i n each col or and si ze f or s i gn t ypes pr ovi ded. Four changeabl e message st r i ps f or s i gn t ypes provided.

PART 2 PRODUCTS

2. 1 MODULAR EXTERI OR SI GNAGE SYSTEM

Ext er i or s i gnage shal l consi st of a syst em of coor di nat ed di r ect i onal , i dent i f i cat i on, and r egul at or y t ype si gns l ocat ed wher e shown.

Di mensi ons, det ai l s, mat er i al s, message cont ent , and desi gn of s i gnage shal l be as shown. Submi t manuf act ur er ' s descr i pt i ve dat a and cat al og cuts.

2. 1. 1 Fr ee- St andi ng Base Mount Pyl on/ Monol i t h Type Si gns

2. 1. 1. 1 Framing

I nt er i or f r ami ng shal l consi st of al umi num t ube col umns wel ded t o compani on pl at es. Per i met er f r ami ng shal l consi st of al umi num angl e f r ami ng wel ded t o t he post and pl at e syst em as desi gned. Fr ami ng member s shal l be desi gned t o per mi t access t o el ect r i cal equi pment and panel r emoval . Mount i ng shal l be pr ovi ded as shown. Openi ngs shal l be seal ed f r om moi st ur e and made t amper - pr oof .

2. 1. 1. 2 Ext er i or Sheet i ng Panel s

Modul ar panel s shal l be pr ovi ded i n s i zes shown on dr awi ngs. Panel s shal l be f abr i cat ed a mi ni mum of 0. 090 i nch t hi ck al umi num. Panel s shal l be hel i ar c wel ded t o f r ami ng syst em . Top and end panel s shal l be r emovabl e and shal l be secur ed by 3/ 16 i nch socket head j ack nut s. Fi ni sh f or met al panel s shal l be anodi zed conf or mi ng t o AA DAF45.

2. 1. 1. 3 Mounting

Mount by secur i ng t o concr et e f oundat i on as i ndi cat ed.

2. 1. 1. 4 Finishes

Base f i ni sh shal l be anodi zed conf or mi ng t o AA DAF45. Met al panel syst em f i ni sh shal l be anodi zed conf or mi ng t o AA DAF45.

Apr i l 2019 Page 4 SECTI ON 10 14 00. 10

2. 1. 2 Panel And Post / Panel Type Si gns

2. 1. 2. 1 Posts

One- pi ece al umi num post s shal l be pr ovi ded wi t h mi ni mum 0. 125 i nch wal l t hi ckness. Post s shal l be desi gned t o accept panel f r ami ng syst em descr i bed. The post shal l be desi gned t o per mi t at t achment of panel f r ami ng syst em wi t hout exposed f ast ener s. Caps shal l be pr ovi ded f or each post.

2. 1. 2. 2 Panel Fr ami ng Syst em

Panel f r ami ng consi st i ng of al umi num sect i ons and i nt er l ocki ng t r ack component s shal l be desi gned t o i nt er l ock wi t h post s wi t h conceal ed fasteners.

2. 1. 2. 3 Panels

Modul ar message panel s shal l be pr ovi ded i n s i zes shown on dr awi ngs.

Panel s shal l be f abr i cat ed a mi ni mum of 0. 090 i nch al umi num. Panel s shal l be desi gned t o be i nt er changeabl e. Face panel s shal l be r emovabl e t o pr ovi de access t o el ect r i cal component s.

2. 1. 2. 4 Finishes anodi zed conf or mi ng t o AA DAF45. Met al panel syst em f i ni sh shal l be anodi zed conf or mi ng t o AA DAF45.

2. 1. 2. 5 Mounting

Pr ovi de r emovabl e mount i ng by a st eel f l ange embedded i n concr et e as indicated.

2. 1. 3 Changeabl e Let t er Di r ect or i es

2. 1. 3. 1 Fr ame and Tr i m

Al umi num al l oy f i ni sh shal l be dar k br onze.

2. 1. 3. 2 Header Pl at es

Header pl at e shal l consi st of backgr ound met al mat chi ng f r ame and havi ng r ai sed l et t er s at t ached t hr ough t he back.

2. 1. 3. 3 Door Gl azi ng

Door gl azi ng shal l be c l ear pol ycar bonat e sheet 3/ 16 i nch t hi ck.

2. 1. 3. 4 Door Const r uct i on

Door f r ame shal l be of same mat er i al and f i ni sh as sur r oundi ng f r ame.

Cor ner s shal l be mi t er ed , r ei nf or ced, and assembl ed wi t h conceal ed f ast ener s. Hi nges shal l be st andar d wi t h manuf act ur er , i n f i ni sh t o mat ch f r ames and t r i m. Gl azi ng shal l be set i n f r ame wi t h r esi l i ent gl azi ng channels.

2. 1. 3. 5 Door Locks

Door l ocks shal l be manuf act ur er ' s st andar d and shal l be keyed al i ke.

Apr i l 2019 Page 5 SECTI ON 10 14 00. 10

2. 1. 3. 6 Fabrication

Fr ames and t r i m shal l be assembl ed wi t h cor ner s r ei nf or ced and mi t er ed t o hai r l i ne f i t , wi t h no exposed f ast ener s. Removabl e changeabl e di r ect or y panel shal l consi st of 1/ 4 i nch t hi ck whi t e acr yl i c wi t h c l ear acr yl i c l et t er t r acks.

2. 1. 3. 7 Finishes

Post f i ni sh shal l be semi - gl oss baked enamel or t wo- component acr yl i c pol yur et hane . Met al panel syst em f i ni sh shal l be baked enamel or t wo- component acr yl i c pol yur et hane .

2. 1. 3. 8 Mounting

Di r ect or i es shal l be mount ed t o suppor t i ng st r uct ur es wi t h conceal ed f ast ener s i n accor dance wi t h manuf act ur er ' s i nst r uct i ons.

2. 1. 3. 9 Changeabl e Let t er s

Changeabl e l et t er s shal l be upper - case or upper and l ower - case hel vet i ca medi um. Tabbed vi nyl l et t er s and number s shal l be f ur ni shed i n accor dance wi t h t he dr awi ngs.

2. 2 ILLUMINATION

Conceal ed l i ght i ng shal l be pr ovi ded wi t hi n panel f r ami ng member s.

Li ght i ng shal l be c El ect r i cal equi pment shal l be UL or FM l i st ed and compl y wi t h NFPA 70. I l l umi nat i on shal l be evenl y di st r i but ed. A swi t ch on t he i nt er i or of t he s i gn shal l be pr ovi ded t o t ur n of f power i n t he s i gn. Swi t ch shal l be r eadi l y accessi bl e when si gn i s open.

2. 3 GRAPHI CS FOR EXTERI OR SI GNAGE SYSTEMS

2. 3. 1 Graphics

Si gnage gr aphi cs shal l conf or m t o t he f ol l owi ng:

a. Pr essur e sensi t i ve pr eci s i on cut v i nyl l et t er s shal l be pr ovi ded.

2. 3. 2 Messages

See dr awi ngsf or message cont ent . Typef ace: Hel vet i ca medi um . Type si ze as i ndi cat ed.

2. 4 METAL PLAQUES

Desi gn and l ocat i on of pl aques shal l be as i ndi cat ed.

2. 4. 1 Cast Met al Pl aques

2. 4. 1. 1 Fabrication

Cast met al pl aques shal l have t he l ogo, embl em and ar t wor k cast i n t he bas r el i ef t echni que. Pl aques shal l be f abr i cat ed f r om br onze.

Apr i l 2019 Page 6 SECTI ON 10 14 00. 10

2. 4. 1. 2 Size

Pl aque si ze shal l be as i ndi cat ed.

2. 4. 1. 3 Border

Bor der shal l be f l at band.

2. 4. 1. 4 Background

Backgr ound t ext ur e shal l be f i ne pebbl e.

2. 4. 1. 5 Mounting

Mount i ng shal l be conceal ed.

2. 4. 1. 6 Finish

Fi ni shes shal l consi st of br onze wi t h dar k f i ni sh oxi di zed backgr ound.

Let t er s shal l be sat i n pol i shed and ent i r e pl aque spr ayed wi t h t wo coat s of c l ear l acquer .

2. 5 DI MENSI ONAL BUI LDI NG LETTERS

2. 5. 1 Fabrication

Let t er s shal l be f abr i cat ed f r om cast al umi num. Let t er s shal l be c l eaned by chemi cal et chi ng or c l eaned ul t r asoni cal l y i n a speci al degr easi ng bat h. Let t er s shal l be packaged f or pr ot ect i on unt i l i nst al l at i on.

2. 5. 2 Typeface

Typef ace shal l be hel vet i ca medi um.

2. 5. 3 Size

Let t er s i ze shal l be as i ndi cat ed.

2. 5. 4 Finish

Anodi zed al umi num f i ni sh shal l be pr ovi ded.

2. 5. 5 Mounting

Thr eaded st uds of number and si ze as r ecommended by manuf act ur er , shal l be used f or conceal ed anchor age. Let t er s whi ch pr oj ect f r om t he bui l di ng l i ne shal l have st ud spacer s l eeves. Let t er s, st uds, and sl eeves shal l be of t he same mat er i al . Suppl y t empl at es f or mount i ng.

2. 6 ALUMI NUM ALLOY PRODUCTS

Al umi num al l oy pr oduct s shal l conf or m t o ASTM B209 f or sheet or pl at e, ASTM B221 f or ext r usi ons and ASTM B26/ B26M or ASTM B108/ B108M f or cast i ngs. Al umi num ext r usi ons shal l be pr ovi ded at l east 1/ 8 i nch t hi ck and al umi num pl at e or sheet at l east 16 gauge t hi ck. Wel di ng f or al umi num pr oduct s shal l conf or m t o AWS C1. 1M/ C1. 1.

Apr i l 2019 Page 7 SECTI ON 10 14 00. 10

2. 7 ANODI C COATI NG

Anodi zed f i ni sh shal l conf or m t o AA DAF45 as f ol l ows:

I nt egr at ed col or anodi zed desi gnat i on AA- M10- C22- A32, Ar chi t ect ur al Cl ass 0. 4 t o 0. 7 mi l .

2. 8 ORGANI C COATI NG

Cl ean, pr i me and gi ve sur f aces a semi - gl oss baked enamel or t wo- component acr yl i c pol yur et hane f i ni sh i n accor dance wi t h NAAMM AMP 500, AMP 505, wi t h t ot al dr y f i l m t hi ckness not l ess t han 1. 2 mi l s.

2. 9 STEEL PRODUCTS

St r uct ur al st eel pr oduct s shal l conf or m t o ASTM A36/ A36M. Sheet and st r i p st eel pr oduct s shal l conf or m t o ASTM A1011/ A1011M. Wel di ng f or st eel pr oduct s shal l conf or m t o AWS D1. 2/ D1. 2M.

2. 10 CAST BRONZE

Fabr i cat e component s wi t h shar p cor ner s, f l at f aces, and accur at e pr of i l es. Remove and pol i sh bur r s and r ough spot s. Fi ni sh f aces t o a uni f or m hi gh l ust er . Cast br onze shal l be i n accor dance wi t h ASTM B62.

2. 11 VI NYL SHEETI NG FOR GRAPHI CS

Vi nyl sheet i ng shal l be 5 t o 7 year pr emi um t ype and shal l be i n accor dance wi t h t he f l ammabi l i t y r equi r ement s of ASTM E84 and shal l be a mi ni mum 0. 003 i nch f i l m t hi ckness. Fi l m shal l i ncl ude a pr ecoat ed pr essur e sensi t i ve adhesi ve backi ng, Cl ass 1, or posi t i onabl e pr essur e sensi t i ve adhesi ve backi ng, Cl ass 3.

2. 12 GLASS

Gl ass shal l be i n accor dance wi t h ASTM C1036, Type I , Cl ass 1, Qual i t y q3 and ANSI Z97. 1.

2. 13 ACRYLI C SHEET

Acr yl i c sheet shal l be i n accor dance wi t h t he f l ammabi l i t y r equi r ement s of ASTM E84 and shal l conf or m t o ANSI Z97. 1.

2. 14 POLYCARBONATE SHEET

Pol ycar bonat e sheet shal l conf or m t o SAE AMS3611.

2. 15 ANCHORS AND FASTENERS

Exposed anchor and f ast ener mat er i al s shal l be compat i bl e wi t h met al t o whi ch appl i ed and shal l mat ch i n col or and f i ni sh and shal l be non- r ust i ng, non- cor r odi ng, and non- st ai ni ng. Exposed f ast ener s shal l be tamper-proof.

Apr i l 2019 Page 8 SECTI ON 10 14 00. 10

2. 16 SHOP FABRI CATI ON AND MANUFACTURE

2. 16. 1 Fact or y Wor kmanshi p

Wor k shal l be assembl ed i n t he shop, as f ar as pr act i cal , r eady f or i nst al l at i on at t he s i t e. Wor k t hat cannot be shop assembl ed shal l be gi ven a t r i al f i t i n t he shop t o ensur e pr oper f i el d assembl y. Hol es f or bol t s and scr ews shal l be dr i l l ed or punched. Dr i l l i ng and punchi ng shal l pr oduce cl ean, t r ue l i nes and sur f aces. Wel di ng t o or on st r uct ur al st eel shal l be i n accor dance wi t h AWS D1. 1/ D1. 1M. Wel di ng shal l be cont i nuous al ong t he ent i r e ar ea of cont act . Exposed wel ds shal l be gr ound smoot h.

Exposed sur f aces of wor k shal l have a smoot h f i ni sh and exposed r i vet i ng shal l be f l ush. Fast eni ngs shal l be conceal ed wher e pr act i cal . I t ems speci f i ed t o be gal vani zed shal l be by hot - di p pr ocess af t er f abr i cat i on i f pr act i cal . Gal vani zat i on shal l be i n accor dance wi t h ASTM A123/ A123M and ASTM A653/ A653M, as appl i cabl e. Ot her met al l i c coat i ngs of st eel sheet shal l be i n accor dance wi t h ASTM A924/ A924M. Joi nt s exposed t o t he weat her shal l be f or med t o excl ude wat er . Dr ai nage and weep hol es shal l be i ncl uded as r equi r ed t o pr event condensat i on bui l dup.

2. 16. 2 Di ssi mi l ar Mat er i al s

Wher e di ssi mi l ar met al s ar e i n cont act , or wher e al umi num i s i n cont act wi t h concr et e, mor t ar , masonr y, wet or pr essur e- t r eat ed wood, or absor pt i ve mat er i al s subj ect t o wet t i ng, t he sur f aces shal l be pr ot ect ed wi t h a coat of asphal t var ni sh or a coat of z i nc- mol ybdat e pr i mer t o pr event gal vani c or cor r osi ve act i on.

2. 16. 3 Shop Pai nt i ng

Sur f aces of mi scel l aneous met al wor k, except nonf er r ous met al , cor r osi on r esi st i ng st eel , and zi nc- coat ed wor k, shal l be gi ven one coat of z i nc- mol ybdat e pr i mer or an appr oved r ust - r esi st i ng t r eat ment and met al l i c pr i mer i n accor dance wi t h manuf act ur er ' s st andar d pr act i ce. Sur f aces of i t ems t o be embedded i n concr et e shal l not be pai nt ed. Upon compl et i on of wor k, damaged sur f aces shal l be r ecoat ed.

2. 17 COLOR, FI NI SH, AND CONTRAST

Col or shal l be as i ndi cat ed on t he dr awi ngs. . Col or l i s t ed i s not i nt ended t o l i mi t t he sel ect i on of equal col or s f r om ot her manuf act ur er s.

For bui l di ngs r equi r ed t o be handi capped- accessi bl e, t he char act er s and backgr ound of s i gns shal l be eggshel l , mat t e, or ot her non- gl ar e f i ni sh.

Char act er s and symbol s shal l cont r ast wi t h t hei r backgr ound - ei t her l i ght char act er s on a dar k backgr ound or dar k char act er s on a l i ght backgr ound.

PART 3 EXECUTI ON

3. 1 INSTALLATION

Si gns, pl aques, or di mensi onal l et t er s shal l be i nst al l ed i n accor dance wi t h appr oved manuf act ur er ' s i nst r uct i ons at l ocat i ons shown on t he appr oved det ai l dr awi ngs; submi t dr awi ngs showi ng el evat i ons of each t ype of s i gn; di mensi ons, det ai l s, and met hods of mount i ng or anchor i ng; shape and t hi ckness of mat er i al s; and det ai l s of const r uct i on. A schedul e showi ng t he l ocat i on, each si gn t ype, and message shal l be i ncl uded.

Ci r cui t s i nst al l ed under gr ound shal l conf or m t o t he r equi r ement s of Sect i on 33 71 02 UNDERGROUND ELECTRI CAL DI STRI BUTI ON. St eel condui t s i nst al l ed under gr ound and i l l umi nat ed si gnage mount ed di r ect l y on

Apr i l 2019 Page 9 SECTI ON 10 14 00. 10 bui l di ngs shal l be i n conf or mance wi t h t he r equi r ement s of Sect i on 26 20 00 I NTERI OR DI STRI BUTI ON SYSTEM. Si gns shal l be i nst al l ed pl umb and t r ue at mount i ng hei ght s i ndi cat ed, and by met hod shown or speci f i ed. Si gns mount ed on ot her sur f aces shal l not be i nst al l ed unt i l f i ni shes on such sur f aces have been compl et ed. Submi t manuf act ur er ' s i nst al l at i on i nst r uct i ons and cl eani ng i nst r uct i ons.

3. 1. 1 Anchorage

Anchor age and f ast ener mat er i al s shal l be i n accor dance wi t h appr oved manuf act ur er ' s i nst r uct i ons f or t he i ndi cat ed subst r at e. Anchor age not ot her wi se speci f i ed or i ndi cat ed shal l i ncl ude sl ot t ed i nser t s, expansi on shi el ds, and powder - dr i ven f ast ener s when appr oved f or concr et e; t oggl e bol t s and t hr ough bol t s f or masonr y; machi ne car r i age bol t s f or st eel ; l ag bol t s and scr ews f or wood.

3. 1. 2 Pr ot ect i on and Cl eani ng

The wor k shal l be pr ot ect ed agai nst damage dur i ng const r uct i on. Har dwar e and el ect r i cal equi pment shal l be adj ust ed f or pr oper oper at i on. Gl ass, f r ames, and ot her s i gn sur f aces shal l be c l eaned i n accor dance wi t h manuf act ur er ' s i nst r uct i ons. Af t er s i gns ar e compl et ed and i nspect ed, Cover al l pr oj ect i dent i f i cat i on, di r ect i onal , and ot her s i gns whi ch may mi sl ead t he publ i c. Cover i ng shal l be mai nt ai ned unt i l i nst r uct ed t o be r emoved by t he Cont r act i ng Of f i cer or unt i l t he f aci l i t y i s t o be opened f or busi ness. Submi t f our copi es of mai nt enance i nst r uct i ons l i s t i ng r out i ne mai nt enance pr ocedur es, possi bl e br eakdowns and r epai r s, and t r oubl eshoot i ng gui des. The i nst r uct i ons shal l i ncl ude si mpl i f i ed di agr ams f or t he equi pment as i nst al l ed. Si gns shal l be c l eaned, as r equi r ed, at t i me of cover r emoval .

3. 2 FI ELD PAI NTED FI NI SH

Mi scel l aneous met al s and f r ames shal l be f i el d pai nt ed i n accor dance wi t h Sect i on 09 90 00 PAI NTS AND COATI NGS. Anodi zed met al s, masonr y, and gl ass shal l be pr ot ect ed f r om pai nt . Fi ni sh shal l be f r ee of scr at ches or ot her blemishes.

- - End of Sect i on - -

Apr i l 2019 Page 10 SECTI ON 10 14 00. 10