Build-to-print machine shop requirements

SOL AMENDMENT 0004:
This amendment is issued to attach Amendment 0001 and Amendment 0002 to this solicitation which was inadvertently left off and to answer industry questions.

SOL AMENDMENT 0003:
This amendment is issued to answer industry questions.

SOL AMENDMENT 0002:
This amendment is to correct amendment 0001 which inadvertently answer the same question two times. Please ignore the last Question and Answer on amendment 001. The closing date and time remains unchanged at 15 July 2019, 2:00 PM EST.

SOL AMENDMENT 0001:
This solicitation amendment is to extend the closing date to 07/15/19, 2:00 pm EST, add Drawing # 1698AS184 to CLIN 0021 and to answer industry questions.

AMENDMENT 0002:
This solicitation is amended to extend the anticipated closing date from 27 MAR 2019 - 2:00 PM EST to 31 MAY 2019 - 2:00 PM EST.

AMENDMENT 0001:

This amendment is to answer an industry question and to upload the CAD file of the product sample, small pintle, Drawing 6650748 REV L.

Question: The top view of the part shows a dimension of .744 from what looks to be the
OD of the thread. The thread specification called is: 1.00-12 UNF - 2A. The major diameter for this thread is .9868-.9982. Using these engineering numbers will produce a quality thread but will
impact the dimension (.744). In question if measured with a micrometer across the O.D of the finished thread. Our concern is if we use the theoretical outside diameter of 1.00 to locate the flat for the .744 dimension. And then measure across the flats with a micrometer you will read very close if not right on the low dimension. Of -.005 (drawing specifies +/- .005 for 3 decimal place dimensions). My concern is the inspector may see this as a defect if they measure less than that .744 called out in the drawing. And fail us for turning in a bad part.

Answer: The intent of this drawing is the major diameter is maintained through the straight portion of the 1.45" turned shaft length. So the .744" is measured from the major diameter of the unthreaded portion of the lower end of the pintle shaft. Maintain your .744 +/-.005" based on the actual measured "Major Diameter".

NAVSEA Crane issued a pre-solicitation synopsis for a 5-year, Firm-Fixed Priced (FFP), with five one-year options, Indefinite Delivery/Indefinite Quantity (IDIQ) contract for Build to Print Machine Shop Requirements. This acquisition is under North American Industry Classification System code (NAICS) 332710 - Machine Shops. The anticipated award has a 5-year ordering period with five one year options for a minimum contract value of $3,000 to a maximum contract value of $35,000,000.

Questions or inquiries should be directed to Mrs. Shawna Gainey, Code 0232, at telephone 812-854-4621, Fax 812-854-1747 or e-mail: shawna.gainey@navy.mil. Please reference the above solicitation number when responding to this notice.

N00164-19-R-JN75 - BUILD-TO-PRINT MACHINE SHOP REQUIREMENTS - FSG 16 - NAICS 332710

Anticipated Issue Date 25 FEB 2019 - Anticipated Closing Date 27 MAR 2019 - 2:00 PM EST

This solicitation is being posted to the Federal Business Opportunities (FBO) page located at http://www.fbo.gov/. FBO is the single point of entry for posting of synopsis and solicitations to the internet. Please feel free to use the FBO site to access information posted by NSWC Crane.

The Naval Surface Warfare Center (NSWC), Crane Division intends to procure machined parts to support Armed Helo Weapons Systems and various ground and air activities in support of the United States Navy. This procurement's performance requirements are based on, but not limited to, Fixed Forward Firing Weapons (FFFW) and Interface Unit Automatic Data Processor (IUADP). The Government anticipate this procurement will culminate in the award of multiple Firm Fixed-Price (FFP), Five-year, with Five (5) one year options, Indefinite Delivery Indefinite Quantity (IDIQ) supply contracts. Drawings will be provided at time of the solicitation for pricing of repetitive, known requirements. Future emergent requirements that fall under the scope of this requirement may be purchased from a build-to-print contract line item that will be competed IAW FAR 16.5 when the requirement becomes known. The units procured under this requirement shall be manufactured in accordance with the Statement of Work (SOW), Contract Data Requirements List (CDRLs) and Technical Drawings. The required delivery schedule will be specified in subsequent delivery orders and it is anticipated to require delivery within a range of 90 - 240 days after effective date of the delivery order, FOB destination, with inspection and acceptance performed at destination.

As part of the proposal submission, one (1) product sample will be required at that time. The product sample of a small pintle shall be built in accordance with Drawing 6650748 REV L. The product sample drawing is attached to this synopsis. The product sample must be in conformance to all specifications and standards outlined in the RFP. Product samples shall be provided at no cost to the government.

This requirement will be issued competitively as a 100% small business set-aside and all responsible sources may submit an offer that will be considered. The Government intends to award to the responsible offerors whose offers constitute the best value to the Government, considering technical, past performance, and price related factors. Split awards may be made for known, repetitive requirements solicited.

It is anticipated that the RFP will be available on or about 25 February 2019 at the following address: www.fbo.gov. RFPs will be in portable document format (PDF). No hard copies of the solicitation will be mailed. Interested sources must download from the www site listed. To download and view these documents, you will need the latest version of Adobe Acrobat Reader. This software is available free at http://www.adobe.com

Contractors must be properly registered in the System for Award Management (SAM) and the Joint Certification Program (JCP) in order to receive the controlled attachments. Offerors may obtain information on SAM registration and annual confirmation requirements by calling 1-866-606-8220 or via the internet at https://www.sam.gov. Information about the JCP is located at http://www.dlis.dla.mil. The controlled attachments will be posted to FedBizOps at the same time the RFP is posted. FedBizOpps may be accessed at http://www.fbo.gov.

All changes that occur prior to the closing date will be posted to the FedBizOpps website. For changes made after the closing date, only those offerors that provide a proposal will be provided any changes/amendments and considered for future discussions and / or award.

The Government point of contact is Mrs. Shawna Gainey at telephone number 812-854-4621, fax 812-854-1747, or e-mail shawna.gainey@navy.mil. Reference the above solicitation number when responding to this notice.