6515--AWARDED - Sole Source Delivery Order Against FSS Contract For Steris Sterilization Equipment.

Cart Washer:

Cart washer (including service area) must be no longer than 122.5 and fit in a finished wall opening of 124 W x 105 H

Safety features to include chamber illumination, emergency stop and door interlock.

Steam Condensate return

Automatic Floor tilt

Chamber capacity minimum 40x80x106

Removable Debris Screen.

Safety Door Switch.

Spraying System

Obstruction Sensor.

Horizontal Sliding Doors

Interior Lights

Emergency Stop Pushbuttons.

Door Interlock.

Lock/Unlock Key Selector.

Emergency stop cable

Non-recirculated, venting drying system

Integral Exhaust

Drain discharge cool down

Heating System

Process data validation system

Wash phase, Thermal Rinse Phase, HEPA-Filtered Air Drying

Touch-screen panel user interface, minumun dimensions 5.5 x 7.0

PC-based control system to monitor and control washer operations and functions as well as store cycle data.

Pre-programable parameters

Qty. 1, Container and Qty 1, Utensil carts

Bar code scanner

Compatible with Steris Prolystica® Ultra Concentrate HP Neutral Detergent

Standards Applied to meet Performance Requirements and Safety: EN ISO 15883-1:2009/Amd 1:2014, ANSI/AAMI ST15883-1:2009 and CAN/CSA Z15883-1:09:2014.

Cart washer will be provided with a maximum 120 high service clearance from finished floor to structural deck, however within this area there are 3 structural beams present running perpendicular to the direction of operation. The bottom of these structural beams will be at a height of 109-7/8 from finished floor. Cart washer installation and utility connections must be coordinated to account for the presence of these beams.

Cart washer must be packaged and delivered to the site in pieces no larger than 49 x 83 x 121 such that it may be handled and will pass through existing openings

Cart washer must be pit-mounted over a concrete recessed pit of dimensions 78 W x 118 L x 6.75 D

Cart washer shall utilize 1-1/2 NPT high pressure steam @ 80 PSI connection

Cart washer shall utilize 1 NPT condensate return connection.

Cart washer shall utilize 4 outside diameter drain connection to a floor sink in the recessed pit

Cart washer shall utilize a 6 round stainless steel exhaust duct connection

Cart washer shall utilize 1 NPT domestic cold water connection

Cart washer shall utilize 1 NPT domestic hot water connection

Cart washer shall utilize ¾ NPT reverse osmosis water connection

Cart washer shall utilize ½ compressed air connection at 80-120 PSI

Cart washer shall utilize a 480V, 20 amp, 3 phase electrical connection

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Washer Disinfectors:

Qty 3, washer disinfectors

Qty 2, three level manifold racks

Qty 1, two level manifold rack

Condensate return

Maximum dimensions of each unit- 42 W x 38 D x 91 H

The 3 washer disinfectors when installed side-by-side must fit in a finished wall opening of 129 W x 96 H

Each washer disinfector must be packaged and delivered to the site in pieces no larger than 47.5 x 93.5 x 47.5 such that they may be handled and will pass through existing openings

Spray arm system providing entire chamber coverage

Audible warning system with adjustable volume

Color touch screen control system and visual progress indicator

Minimum 10 custom cycles

Obstruction Sensor

Safety lockout features

Door interlock feature

Safety STOP pushbutton(s)

Protocol Printer

Each washer disinfector shall utilize 1/2 NPT high pressure steam @ 80 PSI connection

Each washer disinfector shall utilize 1/2 NPT condensate return connection.

Each washer disinfector shall utilize 1-1/2 outside diameter drain connection to a floor sink beneath the unit

Each washer disinfector shall utilize 1/2 NPT domestic cold water connection with operating flow rate of 10.7 to 14.1 GPM

Each washer disinfector shall utilize 1/2 NPT domestic hot water connection with operating flow rate of 6.8 to 14.1 GPM

Each washer disinfector shall utilize 1/2 NPT reverse osmosis water connection

Each washer disinfector shall utilize 1/8 compressed air connection at 80-125 PSI

Each washer disinfector shall utilize a 480V, 30 amp, 3 phase electrical connection

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Hydrogen Peroxide Sterilizers:

Qty 2, low temperature hydrogen peroxide sterilizers

Maximum dimensions of each unit- 33 W x 38-5/16 D x 72 H

Minimum chamber dimensions of each unit- 17 W x 32.5 D x 15 H

At a minimum sterilizer must be able to processes up to 11 lbs of non-lumened devices in 16 minutes

Delayed start and load conditioning features

Minimum of 4 cycles (selectable)

Moisture check feature to confirm loads are dry

Hands-free chamber access for loading

Low Sterilant notification

Cycle information collection for electronic record management

Touch screen controls

Each hydrogen peroxide sterilizer shall include a power cord, and utilize a 208V, 20 amp, 3 phase GFCI receptacle

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Small Sterilizer:

Qty 1 single door sterilizer

Dimensions of 45 5/8 L x 30 W x 74 ½H

Must fit in a finished wall opening of 28-1/8 W x 74-1/4 H. Accommodate finished wall thickness between 4 and 8 .

Minimum chamber size of 20 x 20 x 38

Minimum Qty 1, rack and Qty 2 shelves

Vertical sliding door

Allow for hands-free loading and unloading

Ability to process up to 3 25lb trays, minimum

Meets current AAMI/AORN guidelines

Must interface with Censitrac

Sterilizers shall have ink on paper printout

Shall have a Dart (Bowie-Dick) and vacuum leak test cycles

Pressure chamber shall have a full jacket

Minimum 12 programmable cycles - gravity and pre-vacuum

Touch screen display

Ability to furnish a duplicate printout of each cycle

Minimum qty 1, loading trolley with one loading rack

Small sterilizer must fit and be operational within a 52 W x 52 D service clearance area.

Small sterilizer shall utilize 1/2 NPT high pressure steam @ 80 PSI connection. Peak steam consumption of 158 LB/HR, average cycle 42 LB max.

Small sterilizer shall utilize 1-1/2 outside diameter drain connection to a floor sink beneath the unit

Small sterilizer shall utilize 1 NPT domestic cold water connection at 30-50 PSI. Peak water consumption of 15 GPM, average cycle 175 GAL max.

Small sterilizer shall utilize a 120V, 20 amp, single phase electrical connection

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Automated Passthrough Window Single Shelf:

Qty 1, Automated Passthrough Window with Single Shelf

Must fit in a finished wall opening of 28-1/4 W x 45-1/4 H. Accommodate finished wall thickness of 4-7/8 .

Minimum service opening : 24 W x 17-1/2 H.

Frame : Aluminum extrusions

Finish : Clear anodized aluminum

Minimum 1/4 Clear tempered glass

Automatically opens and closes

Dual microwave sensor actuation from both interior and exterior side

304 stainless steel shelf

Shelf to extend minimum 4 from window frame on the soiled side, maximum 25 from window frame on the clean side

Provide angled wall supports beneath shelf

Opener shall utilize a 120V, 20 amp, single phase electrical connection

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Automated Passthrough Window Double Shelf:

Qty 2, automated passthrough windows with double shelf

Must fit in a finished wall opening of 28-1/4 W x 45-1/4 H. Accommodate finished wall thicknesses of 4-7/8 and 7-1/4 .

Minimum service opening : 24 W x 17-1/2 H.

Frame : aluminum extrusions

Finish : clear anodized aluminum

Minimum 1/4 Clear tempered glass

Automatically opens and closes

Dual microwave sensor actuation from both interior and exterior side

304 stainless steel shelves

Shelf to extend minimum 4 from window frame on the soiled side, maximum 25 from window frame on the clean side

Provide angled wall supports beneath shelves

Opener shall utilize a 120V, 20 amp, single phase electrical connection

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Rack Return Window:

Qty 1, rack return window for transferring washer disinfector manifold racks between clean and soiled sides of the SPS department.

Overall dimensions 34-3/4 W x 39-11/16 L x 93 H

Minimum interior chamber dimensions 27-1/8 W x 33-1/8 L x 28-9/16 H

Must fit in a rough wall opening of 36-3/8 W x 48-1/2 H. Accommodate finished wall thickness of 4-7/8

Provide wall flanges for finished opening

Minimum Qty 2, auto docking transfer cart adapters

Automated doors to allow handsfree operation

Interlocking doors

Obstruction sensor

Manually operated safety lock/hold open on both doors

Status indicator lighting

Voice communication system to allow operators on each side to communicate

Capable of handling fully loaded racks up to 160 lbs minimum

Unit shall utilize a 120V, 20 amp receptacle

Unit shall utilize 1/8 NPT compressed air connection at 80-100 PSI

Adapter for transfer cart docking

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Sonic Irrigators:

Qty 2, sonic irrigators

Maximum dimensions of each unit- 35 W x 26 D x 44 H

Minimum wash chamber dimensions of each unit- 29.5 W x 14.4 D x 9.3 H

Frequencies shall adjust to compensate for load variations

Unit provides ANSI/AAMI ST 15883-2:2013 4.3 compliant Thermal Disinfection

Minimum reprocess of 20 lumened devices or minimum 44 lbs in every cycle

Internal chemical cupboard for 2 bottles of maximum size 9 W x 8 D x 17 H

Automated dosing and delivery of chemicals

Meets all robotic instrument IFU requirements with automated wash, flush and rinse cycles

Integrated record keeping

Capability to export key cycle parameters

Automated locking lid

Compatible with most common instrument trays used in healthcare settings

Touch screen controls

Maximum noise output of 68 dB @ 1 meter in front of the machine

Each sonic irrigator shall utilize 1-1/2 outside diameter drain connection to a floor sink beneath the unit

Each sonic irrigator shall utilize 1/2 NPT domestic cold water connection with operating flow rate of 3 to 8 GPM

Each sonic irrigator shall utilize 1/2 NPT domestic hot water connection with operating flow rate of 3 to 8 GPM

Each sonic irrigator shall utilize 1/2 NPT reverse osmosis water connection with operating flow rate of 3 to 8 GPM

Each sonic irrigator shall utilize 1/2 compressed air connection at 30-40 PSI

Each sonic irrigator shall utilize a 208V, 35 amp, 3 phase electrical connection

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Scope Station Triple Bay Sinks:

Qty 2, right to left workflow triple bay sinks

Qty 2, left to right workflow triple bay sinks

Each unit must be packaged and delivered to the site in pieces no larger than 132 x 36 x 48 such that they may be handled and will pass through existing openings

Overall maximum unit dimensions 120 W x 28-1/32 D x 52-17/32 T (at max operating height)

Three basins, each with minimum dimensions 30 x 17 x 10"

Stainless Steel Construction

Air and water pistol attachments

Magnetic back splash

Drain system and flex plates

Etched gallon markers in all bays

Must be height adjustable, with minimum working surface height range of 33 to 41

Minimum weight capacity of adjustment lift 562 lbs

Minimum speed of adjustment system 3/8 per second

Must have Pure water faucet

Each unit shall come with a P-trap and utilize a 1-1/2 diameter drain connection.

Each unit shall utilize 1/2 NPSM domestic cold water connection with pressure range of 20 to 44 PSIG

Each unit shall utilize 1/2 NPSM domestic hot water connection with pressure range of 20 to 44 PSIG

Each unit shall utilize 1/2 NPSM reverse osmosis water connection with pressure range of 50 to 150 PSIG

Each unit shall utilize 1/4 compressed air connection at 30 PSI

Each unit shall utilize a 120V, 20 amp, GFCI protected receptacle

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Work Station Triple Bay Sinks:

Qty 2, right to left workflow triple bay sinks

Qty 2, left to right workflow triple bay sinks

Each unit must be packaged and delivered to the site in pieces no larger than 132 x 36 x 48 such that they may be handled and will pass through existing openings

Overall maximum unit dimensions 120 W x 28-1/32 D x 52-17/32 T (at max operating height)

Three basins, each with minimum dimensions 30 x 17 x 10"

Stainless Steel Construction

Air and water pistol attachments

Magnetic back splash

Drain system and flex plates

Etched gallon markers in all bays

Must be height adjustable, with minimum working surface height range of 33 to 41

Minimum weight capacity of adjustment lift 562 lbs

Minimum speed of adjustment system 3/8 per second

Must have Pure water faucet

Each unit shall come with a P-trap and utilize a 1-1/2 diameter drain connection.

Each unit shall utilize 1/2 NPSM domestic cold water connection with pressure range of 20 to 44 PSIG

Each unit shall utilize 1/2 NPSM domestic hot water connection with pressure range of 20 to 44 PSIG

Each unit shall utilize 1/2 NPSM reverse osmosis water connection with pressure range of 50 to 150 PSIG

Each unit shall utilize 1/4 compressed air connection at 30 PSI

Each unit shall utilize a 120V, 20 amp, GFCI protected receptacle

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Double Bay Sink:

Qty 1, double bay sink with left to right workflow

Each unit must be packaged and delivered to the site in pieces no larger than 101 x 36 x 48 such that they may be handled and will pass through existing openings

Overall unit dimensions 96 W x 28-1/32 D x 52-17/32 T (at max operating height)

Two basins, each with minimum dimensions 30 x 17 x 10"

Stainless Steel Construction

Air and water pistol attachments

Magnetic back splash

Drain system and flex plates

Etched gallon markers in all bays

Must be height adjustable, with minimum working surface height range of 33 to 41

Minimum weight capacity of adjustment lift 562 lbs

Minimum speed of adjustment system 3/8 per second

Must have pure water faucet

Each unit shall come with a P-trap and utilize a 1-1/2 diameter drain connection.

Each unit shall utilize 1/2 NPSM domestic cold water connection with pressure range of 20 to 44 PSIG

Each unit shall utilize 1/2 NPSM domestic hot water connection with pressure range of 20 to 44 PSIG

Each unit shall utilize 1/2 NPSM reverse osmosis water connection with pressure range of 50 to 150 PSIG

Each unit shall utilize 1/4 compressed air connection at 30 PSI

Each unit shall utilize a 120V, 20 amp, GFCI protected receptacle

Provide Manufacturers User Manuals and Service Manuals

Provide start up and operator training

Prep & Pack Table

QTY 6 Prep and Pack tables

Must be height adjustable

Max dimensions must be 73 W x 40 D x 86 H

Must have lockable casters

Adjustable, Overhead, LED Lighting

CPU Holder

Surface-Mounted Flat Screen Monitor Arm

Multi-function shelving

Each unit shall utilize a 120V, 20 amp receptacle

Provide Manufacturers User Manuals and Service Manuals

Perform installation

Provide start up and operator training Awarded contract V797D6061336C26322F0112 to STERIS CORPORATION for 1143159.81000000 on 2022-09-15.