858-B310-01_WELD_SCHEDULE.pdf

REV ZONE BY CHECK

1 ALL JEL GWB

2 ALL JEL CCW

GENERAL NOTES

NO. REV

2. ADDED GENERAL NOTES 7 AND 8

REVISION HISTORY

DESCRIPTION DATE

1. ADDED WELDS FOR WINCH FOUNDATION 30 May 19

1) Where beams, stiffeners, frames, etc., pass through slotted girders, shelves or stringers, there is to be a pair of matched intermittent welds on each side of each such intersection, and the beams, stiffeners and frames are to be efficiently attached to the girders, shelves and stringers.

2) Longitudinal frames are to have 6 inches of double continuous welding at their ends and in way of transverses except as follows. Deck longitudinals require 6 inches double continuous welding at ends.

3) The required welding area of end connections of stanchions and diagonals is not to be less than the following:

● Stanchions –75% of the area of the stanchions

● Diagonals – 50% of the area of the diagonal

In determining the weld area provided, the throat dimension of the fillet is to be used.

4) Unbracketed shell and bulkhead stiffeners are to have double continuous welds for one-tenth of their length at each end.

5) Fillet welds are defined by Leg Size (w), Length of Fillets (l), and Spacing of Fillets (S) in inches, in accordance with ABS Rules for

Building and Classing Steel Vessels for Service on Rivers and Intracoastal Waterways

6) Welds inside TANK1.P, located on frames 7-11, are to be double continuous.

7) See BHGI drawings 858-B301-01 Midship & Typ Sections, 858-B305-01 Scantling Plan, and 858-B330-02 Winch Foundation for weld locations.

8) Specified AISC pre-qualified CJP welds in place of fillet welds > 1/2".

US ARMY CORPS OF ENGINEERS

3. GENERAL REVISION

1. UPDATED FOR DESIGN DEVELOPMENT 15 Aug 19

DRAWN BY:

VESSEL:

130'x70'x12' Bank Grading Unit

HULL NO:

DATE

22 Mar 2019

BRISTOL HARBOR GROUP, INC.

THIS DOCUMENT IS THE EXCLUSIVE PROPERTY OF TSGI AND

IS FURNISHED ON A CONFIDENTIAL BASIS. NO PORTION OF

THIS DOCUMENT MAY BE COPIED, TRACED, PHOTOGRAPHED,

OR IN ANY OTHER WAY REPRODUCED, NOR MAY ANY ITEM

HEREON DEPICTED BE MANUFACTURED AS SHOWN WITHOUT

THE EXPRESS WRITTEN CONSENT OF TSGI. THE RECIPIENT

OF THE INFORMATION CONTAINED HEREON MAY NOT DISCLOSE

OR MAKE AVAILABLE THE SAME TO ANY OTHER PERSON OR

BUSINESS FIRM, NOR MAY THE SAME BE USED EXCEPT FOR

THE SPECIFIC PURPOSE INTENDED. TSGI SHALL NOT BE

HELD RESPONSIBLE FOR ANY UNAUTHORIZED CHANGES TO

THIS DOCUMENT OR ITS INTENT

REFERENCES

TITLE:

Weld Schedule

FOR:

JEL

CHECK BY:

GWB

SCALE:

N.T.S.

DWG. NO:

858-B310-01

REV:

DRAWING TITLE

# Joint Description Th. 1 Th. 2 Joint Type Side 1 Weld w (l x S)

Side 2 Weld w (l x S)

1 Dk Pl / SS 1/2 3/4 Lap Seam 5/16 (Cont.) 5/16 (Cont.)

2 SS / Bilge 3/4 1 Lap Seam 1/2 (Cont.) 1/2 (Cont.)

3 Bilge / Btm Pl 1 1/2 Lap Seam 5/16 (Cont.) 5/16 (Cont.)

4 Dk Pl / Apron 1/2 3/4 Lap Seam 5/16 (Cont.) 5/16 (Cont.)

5 Apron / SS 3/4 3/4 Lap Seam 1/2 (Cont.) 1/2 (Cont.)

6 Apron / Apron Wear Pl 3/4 1/2 Lap Seam 5/16 (Cont.) 5/16 (Cont.)

7 Dk Pl / Dk Insert Pl 1/2 1 Butt

8 Dk Pl / End Bhd 1/2 3/4 Lap Seam 5/16 (Cont.) 5/16 (Cont.)

9 Dk Pl / CL Longl Bhd (In Tank) 1/2 3/4 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

10 Dk Pl / WT Longl Bhd (In Tank) 1/2 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

11 Dk Pl / NT Longl Bhd 1/2 1/2 Tee Bndry 3/8 (Cont.) 3/8 (Cont.)

12 Dk Pl / WT Xvrs Bhd (In Tank) 1/2 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

13 Dk Pl / NT Xvrs Bhd 1/2 1/2 Tee Bndry 3/8 (Cont.) 3/8 (Cont.)

14 Btm Pl / CL Longl Bhd (In Tank) 1/2 3/4 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

15 Btm Pl / WT Longl Bhd (In Tank) 1/2 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

16 Btm Pl / NT Longl Bhd 1/2 1/2 Tee Bndry 3/8 (Cont.) 3/8 (Cont.)

17 Btm Pl / WT Xvrs Bhd (In Tank) 1/2 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

18 Btm Pl / NT Xvrs Bhd 1/2 1/2 Tee Bndry 3/8 (Cont.) 3/8 (Cont.)

19 SS / WT Xvrs Bhd (In Tank) 3/4 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

20 Deleted - - - - -

21 Bilge / WT Xvrs Bhd (In Tank) 1 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

22 Deleted - - - - -

23 Bilge / CL Longl Bhd (In Tank) 1 3/4 Tee Bndry 1/2 (Cont.) 1/2 (Cont.)

24 Bilge / WT Longl Bhd (In Tank) 1 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

25 Bilge / NT Longl Bhd 1 1/2 Tee Bndry 3/8 (Cont.) 3/8 (Cont.)

26 End Bhd / Bilge 3/4 1 Lap Seam 1/2 (Cont.) 1/2 (Cont.)

27 Dk Pl / MDT 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

28 MDT / Brkt 1/2 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

29 MDT / Brkt 1/2 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

30 Deleted - - - - -

31 Btm Pl / Btm Xvrs 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

32 Btm Xvrs / Brkt 1/2 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

33 Btm Xvrs / Brkt 1/2 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

34 SS / SS Vert 3/4 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

35 SS Vert / Brkt 1/2 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

36 Dk Insert Pl / MDT 1 1/2 General 5/16 (Cont.) 5/16 (Cont.)

37 CL Longl Bhd / Bhd Vert 3/4 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

38 WT Longl Bhd / Bhd Vert 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

39 NT Longl Bhd / Bhd Vert 1/2 1/2 General 5/16 (2.5 x 14*) 5/16 (2.5 x 14*)

40 Bhd Vert / Brkt 1/2 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

41 WT Xvrs Bhd / Bhd Vert 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

42 WT Xvrs Bhd / Truss Bhd Vert 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

43 WT Xvrs Bhd / CL Longl Bhd (In Tank) 1/2 3/4 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

44 WT Xvrs Bhd / WT Longl Bhd (In Tank) 1/2 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

45 WT Xvrs Bhd / NT Longl Bhd 1/2 1/2 Tee Bndry 5/16 (Cont.) 3/8 (Cont.)

46 NT Xvrs Bhd / Bhd Vert 1/2 1/2 General 5/16 (2.5 x 14*) 5/16 (2.5 x 14*)

47 Deleted - - - - -

48 NT Xvrs Bhd / WT Longl Bhd 1/2 1/2 Tee Bndry 9/32 (Cont.) 5/16 (2.5 x DC)

49 NT Xvrs Bhd / NT Longl Bhd 1/2 1/2 Tee Bndry 5/16 (Cont.) 3/8 (Cont.)

50 End Bhd / End Bhd Vert 3/4 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

51 End Bhd / Truss End Bhd Vert 3/4 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

52 End Bhd / CL Longl Bhd (In Tank) 3/4 3/4 Tee Bndry 1/2 (Cont.) 1/2 (Cont.)

53 End Bhd / WT Longl Bhd (In Tank) 3/4 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

54 End Bhd / NT Longl Bhd 3/4 1/2 Tee Bndry 5/16 (Cont.) 3/8 (Cont.)

55 Dk Pl / Truss Dk 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

56 Truss Dk / Truss End Bhd Vert 1/2 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

57 Truss End Bhd Vert / Truss Btm 1/2 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

58 Btm Pl / Truss Btm 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

59 Truss Btm / Truss Bhd Vert (In Mid 0.5L) 1/2 1/2 Lap End 1/2 (Cont.) 1/2 (Cont.)

60 Truss Bhd Vert / Truss Dk (In Mid 0.5L) 1/2 1/2 Lap End 1/2 (Cont.) 1/2 (Cont.)

61 Truss Dk / Truss Vert (In Mid 0.5L) 1/2 5/8 Lap End 1/2 (Cont.) 1/2 (Cont.)

62 Truss Dk / Truss Diag (In Mid 0.5L) 1/2 1/2 Lap End 1/2 (Cont.) 1/2 (Cont.)

63 Truss Btm / Truss Vert (In Mid 0.5L) 1/2 5/8 Lap End 1/2 (Cont.) 1/2 (Cont.)

64 Truss Btm / Truss Diag (In Mid 0.5L) 1/2 1/2 Lap End 1/2 (Cont.) 1/2 (Cont.)

65 Truss Dk / MDT 1/2 1/2 Cutout Tack 3/16 (Cont.) 3/16 (Cont.)

66 Truss Btm / Btm Xvrs 1/2 1/2 Cutout Tack 3/16 (Cont.) 3/16 (Cont.)

67 Truss Dk / WT Xvrs Bhd 1/2 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

68 Truss Btm / WT Xvrs Bhd 1/2 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

69 Inner Btm / Inner Btm Floors 1/2 1/2 Tee Bndry 3/16 (Cont.) 5/16 (2.5 x 12)

70 Inner Btm Floors / Btm Pl 1/2 1/2 Tee Bndry 3/16 (Cont.) 5/16 (2.5 x 12)

AISC CJP Weld: B-U2

# Joint Description Th. 1 Th. 2 Joint Type Side 1 Weld w (l x S)

Side 2 Weld w (l x S)

71 Inner Btm Floors / WT Longl Bhd 1/2 1/2 Tee Bndry 3/16 (Cont.) 5/16 (2.5 x 12)

72 Inner Btm Floors / CL Longl Bhd 1/2 3/4 Tee Bndry 3/16 (Cont.) 5/16 (2.5 x 12)

73 Inner Btm / WT Longl Bhd (In Tank) 1/2 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

74 Inner Btm / CL Longl Bhd (In Tank) 1/2 3/4 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

75 Inner Btm / WT Xvrs Bhd (In Tank) 1/2 1/2 Tee Bndry 5/16 (Cont.) 5/16 (Cont.)

76 CL Longl Bhd / Brkt 3/4 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

77 NT Longl Bhd / MDT 1/2 1/2 Cutout Tack 3/16 (Cont.) 3/16 (Cont.)

78 NT Longl Bhd / Btm Xvrs 1/2 1/2 Cutout Tack 3/16 (Cont.) 3/16 (Cont.)

79 Deleted - - - - -

80 Deleted - - - - -

81 Dk Pl / Apron MDT 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

82 Apron MDT / Brkt 1/2 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

83 Apron MDT / Brkt 1/2 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

84 Deleted - - - - -

85 SS / SS Vert IWO Apron 3/4 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

86 SS Vert IWO Apron / Brkt 1/2 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

87 Deleted - - - - -

88 Winch Fnd Insert Pl / Winch Fnd Xvrs 1 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

89 Winch Fnd Insert Pl / Winch Fnd Longl 1 3/4 Tee End

90 Winch Fnd Insert Pl / MDT IWO Winch Fnd 1 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

91 Winch Fnd Insert Pl / Longl Brkt IWO Winch Fnd 1 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

92 Winch Fnd Insert Pl / Dk Pl 1 1/2 Butt

93 Winch Fnd Base Pl / Winch Fnd Xvrs 1 1/2 Lap End 3/8 (Cont.) 3/8 (Cont.)

94 Winch Fnd Base Pl / Winch Fnd Longl 1 3/4 Tee End

95 Winch Fnd Xvrs / Winch Fnd Longl 1/2 3/4 Tee End

96 MDT IWO Winch Fnd / Xvrs Brkt IWO Winch Fnd 1/2 1/2 Bracket 5/16 (3.0 x 6) 5/16 (3.0 x 6)

97 MDT IWO Winch Fnd / Longl Brkt IWO Winch Fnd 1/2 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

98 Dk Pl / MDT IWO Winch Fnd 1/2 1/2 General 5/16 (2.5 x 12) 5/16 (2.5 x 12)

99 Truss Dk / MDT IWO Winch Fnd 1/2 1/2 Tee End

100 Truss Dk / Xvrs Brkt IWO Winch Fnd 1/2 1/2 Bracket 5/16 (3.0 x 6) 5/16 (3.0 x 6)

101 Truss Dk / MDT 1/2 1/2 Tee End 3/8 (Cont.) 3/8 (Cont.)

See General Notes on Title Page

* Fillet welds are to be staggered

AISC: TC-U4b + 3/16" Reinforcing Fillets

AISC: TC-U4b + 3/16" Reinforcing Fillets

AISC CJP Weld: B-U2

AISC: TC-U4b + 3/16" Reinforcing Fillets

AISC: TC-U4b + 3/16" Reinforcing Fillets