Amendment_0003_W912DY-18-T-0251.pdf

DIRECTORATE OF CONTRACTING - HNC

ATTN: LOURDES ROMAN

256-895-2507

HUNTSVILLE AL 35816

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

30-105-04EXCEPTION TO SF 30

APPROVED BY OIRM 11-84

STANDARD FORM 30 (Rev. 10-83) Prescribed by GSA

FAR (48 CFR) 53.243

The purpose of this amendment is to:

1. Incorporate a revised Attachment 2 (FID), dated 30 July 2018.

2. All other terms and conditions remain unchanged.

1. CONTRACT ID CODE PAGE OF PAGES

1 2

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

16C. DATE SIGNED

BY

16B. UNITED STATES OF AMERICA15C. DATE SIGNED15B. CONTRACTOR/OFFEROR

(Signature of Contracting Officer)(Signature of person authorized to sign)

8. NAME AND ADDRESS OF CONTRACTOR (No., Street, County, State and Zip Code) X W912DY18T0251

X 9B. DATED (SEE ITEM 11)

11-Jul-2018

10B. DATED (SEE ITEM 13)

9A. AMENDMENT OF SOLICITATION NO.

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

X The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offer is extended, X is not extended.

Offer must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing Items 8 and 15, and returning 1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN

REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE

CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(B).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

10A. MOD. OF CONTRACT/ORDER NO.

U0003

2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO.(If applicable)

6. ISSUED BY

3. EFFECTIVE DATE

30-Jul-2018

CODE

US ARMY ENGINEERING & SUPPORT CENTER

HUNTSVILLE ENGINEERING & SUPPORT CENTER

P.O. BOX 1600

HUNTSVILLE AL 35807-4301

W912DY 7. ADMINISTERED BY (If other than item 6)

4. REQUISITION/PURCHASE REQ. NO.

CODE W912DY

FACILITY CODECODE

EMAIL:TEL:

x 1

W912DY18T0251

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

SUMMARY OF CHANGES

(End of Summary of Changes)

AMD 7/30/18 Furniture Item Descriptions (FID) Army Lodging, Europe Region and Camp Zama, Japan, FY18

Attachment #2 Page 1 of 70

Attachment #2

Furniture Item Descriptions (FID)

Attachment #2 Page 2 of 70

TABLE OF CONTENTS PAGE NO.

1.0 GENERAL

1.1 Submittal Requirements

1.1.1 RFQ Response

1.1.2 Non-Conforming RFQ Response

1.2 Submittal and Clarifications Format

1.3 Post Award Submittal

2.0 CONTRACTOR GENERAL NOTES

3.0 Mattresses

3.1 Item No. MQ-2: Mattress, Queen

3.2 Item No. MQ-1: Mattress, Queen

3.3 Item No. MT-1: Mattress, Twin

4.0 Foundations

4.1 Item No. FQ-2: Foundation, Queen

4.2 Item No. FQ-1: Foundation, Queen

4.3 Item No. FT-1: Foundation, Twin

5.0 Bed Bases

5.1 Item No. BQ-1: Bed Base, Queen

5.2 Item No. BF-1: Bed Base, Full

6.0 Metal/Laminate Desks – NOT USED

7.0 Metal Furniture: Lateral Files and Storage Towers/Cabinets– NOT USED

8.0 Laminate Tables, Metal Bases – NOT USED

9.0 Laminate Training Tables – NOT USED

10.0 Wood Casegoods – Europe

10.1 Item No. HB-5: Wall Hung Headboard, Full Size, Wood Veneer

10.2 Item No. HB-2: Wall Hung Headboard, Queen Size, Wood Veneer

10.3 Item No. HB-3: Wall Hung Headboard, Queen Size, Wood Veneer

10.4 Item No. HB-4: Wall Hung Headboard, Queen Size, Wood Veneer

10.5 Item No. NS-5: Night Stand, Small, Laminate/Wood Veneer

10.6 Item No. NS-1A: Night Stand, Small, Laminate/Wood Veneer

10.7 Item No. NS-1C: Replacement Top for Night Stand, Small, Laminate/Wood Veneer

10.8 Item No. NS-1D: Replacement Top for Night Stand, Small, Laminate/Wood Veneer

10.9 Item No. NS-1E: Replacement Top for Night Stand, Small, Laminate/Wood Veneer

10.10 Item No. NS-3: Night Stand, Large, Laminate/Wood Veneer

10.11 Item No. NS-4: Night Stand, Small, Laminate/Wood Veneer

10.12 Item No. W-1: Wardrobe Storage Cabinet, Laminate/Wood Veneer

10.13 Item No. W-1A: ADA Wardrobe Storage Cabinet, Laminate/Wood Veneer

10.14 Item No. W-2: Wardrobe Storage Cabinet, Laminate/Wood Veneer

10.15 Item No. W-4: Wardrobe Storage Cabinet, Laminate/Wood Veneer

10.16 Item No. TC-2: TV Chest of Drawers, Laminate/Wood Veneer

10.17 Item No. TC-5: TV Chest of Drawers, Laminate/Wood Veneer

10.18 Item No. TC-4: TV Chest of Drawers, Laminate/Wood Veneer

Attachment #2 Page 3 of 70

10.19 Item No. TC-2B: Replacement Top for TV Chest of Drawers, Laminate/Wood Veneer

10.20 Item No. TC-2C: Replacement Top for TV Chest of Drawers, Laminate/Wood Veneer

10.21 Item No. TC-2D: Replacement Top for TV Chest of Drawers, Laminate/Wood Veneer

10.22 Item No. CR-2: Credenza, Laminate/Wood Veneer

10.23 Item No. CT-2: Chest Top Hutch, Laminate/Wood Veneer, Powered

10.24 Item No. D-8: Writing Desk, Laminate/Wood Veneer, Non-Powered

10.25 Item No. D-5: Writing Desk, Laminate/Wood Veneer

10.26 Item No. D-6: Writing Desk, Laminate/Wood Veneer

10.27 Item No. D-3C: Replacement Top for Writing Desk, Laminate/Wood Veneer

10.28 Item No. D-3D: Replacement Top for Writing Desk, Laminate/Wood Veneer

10.29 Item No. D-7: Writing Desk, Laminate/Wood Veneer, Non-Powered

10.30 Item No. T-5: Mobile Writing Table, Laminate/Wood Veneer

10.31 Item No. T-6: Mobile Writing Table, Laminate/Wood Veneer

10.32 Item No. D-3B: Replacement Top for Mobile Writing Table, Laminate/Wood Veneer

10.33 Item No. T-1: Rectangular Coffee Table

10.34 Item No. T-7: Rectangular Coffee Table

10.35 Item No. T-2: Rectangular End Table, Laminate/Wood Veneer

10.36 Item No. T-8: Rectangular End Table, Laminate/Wood Veneer

10.37 Item No. T-4A: Round Pedestal Dining Table, Laminate/Wood Veneer

10.38 Item No. T-9: Round Pedestal Dining Table, Laminate/Wood Veneer

10.39 Item No. T-5 T-10: Round Pedestal Dining Table, Laminate/Wood Veneer

10.40 Item No. T-8A: Replacement Top for Round Pedestal Dining Table, Laminate/Wood

Veneer

11.0 Ergonomic Task Seating

11.1 Item No. CH-1: Ergonomic Task Chair, Upholstered, Mesh or Polymer Back

12.0 Seating, Metal Frame, Wood – NOT USED

13.0 Seating, Wood Frame

13.1 Item No. CH-4: Dining Chair, Wood Frame, Faux Leather

13.2 Item No. CH-10: Dining Chair, Wood Frame, Faux Leather

13.3 Item No. CH-11: Desk Chair, Wood Frame, Upholstered

14.0 Lounge Seating

14.1 Item No. R-1: Recliner

14.2 Item No. R-2: Recliner

15.0 Sleeper Sofas & Mattresses

15.1 Item No. SS-1: Queen Size Sleeper Sofa with Mattress, Upholstered

15.2 Item No. SS-2: Queen Size Sleeper Sofa with Mattress, Upholstered

15.3 Item No. SS-3: Full Size Sleeper Sofa with Mattress, Upholstered (Vicenza –

Ederle)

16.0 Sleeper Sofa Mattresses – NOT USED

17.0 Occasional Tables – NOT USED

18.0 Lamps

18.1 Item No. L-1: Night Stand Lamp

18.2 Item No. L-2: Floor Lamp

Attachment #2 Page 4 of 70

19.0 Televisions – NOT USED

20.0 Washers and Dryers – NOT USED

21.0 Refrigerators– NOT USED

22.0 Cooktops – NOT USED

23.0 Microwave Ovens – NOT USED

24.0 Dishwasher– NOT USED

25.0 Luggage Carts – NOT USED

26.0 Scissor Lifts – NOT USED

27.0 Housekeeping Carts

27.1 Item No. HK-4: Housekeeping Cart

27.2 Item No. HK-5: Housekeeping Cart, Compact

27.3 Item No. HK-6: Laundry Cart

27.4 Item No. HK-7: Linen Cart

28.0 Forklifts – NOT USED

29.0 Ice Machine and Dispenser – NOT USED

30.0 Ironer – NOT USED

31.0 Carpet Extractor/Shampooer

31.1 Item No. HK-2: Carpet Extractor

31.2 Item No. HK-3: Carpet Extractor, Compact

32.0 Room/Air Cleaning System– NOT USED

33.0 Fitness Equipment – NOT USED

34.0 Ancillary

34.1 Item No. AR-1: Recycle Station

34.2 Item No. AR-2: Recycle Station

END OF SECTION

Attachment #2 Page 5 of 70

1.0 General

Item descriptions and quality requirements, as described in the FID (Furniture Item Descriptions), are for the quality, functional performance and design intent of the furnishings required for this project. Products quoted that meet all functional and quality requirements, including all salient features listed in the product descriptions, will be considered responsive provided they are fully compliant with the RFQ requirements.

Compliance shall be determined by performance, features, quality, design intent, and value. Any item descriptions, salient features or quality requirements listed within this document are not intended to be proprietary.

1.1 Submittal Requirements

All manufacturers shall provide manufacturer’s technical documentation and manufacturer’s construction specifications for each item quoted for verification the proposed products meet all requirements listed in the FID. The RFQ response shall be submitted in the format outlined below.

1.1.1 RFQ Response

RFQ technical responses are the documents which, together with contractual documents (SF18, SF30, Attachment 1 in Excel), make up an overall RFQ response (the quote). RFQ technical responses shall be clearly organized into (1) Adobe Acrobat (PDF) document. The PDF document shall be searchable and include book marks for each item number and be organized per item number of the FID. Each RFQ is a separate contract activity, and specifications from previous projects will not be retrieved and reviewed. All product specifications and information presented shall be legible.

All technical documentation related to each item number shall be located within the same tab in the RFQ response and shall be submitted in the following order:

1. Product Information Required for Each Item Number:

a. Item number for each product submitted in the RFQ response.

b. Manufacturer, product line, and model number for each item and its components.

c. Overall dimensions.

d. Product image.

e. Fabric and finish options proposed for RFQ pricing that have been priced for each item.

2. Product Specific Compliance Documentation:

a. Provide published, detailed, technical documentation including, but not limited to, specification guides, price catalogs, and manufacturer’s published Price List to demonstrate compliance with requirements.

b. Highlight, circle, or mark the model, size, type, and any optional features proposed in the RFQ response.

3. Technical Supporting Compliance Documentation:

a. Provide manufacturer’s technical and construction specifications demonstrating compliance to requirements.

Attachment #2 Page 6 of 70

b. Documentation shall only be submitted once for multiple items from the same product line.

c. Clearly indicate the item numbers that submitted documentation supports.

4. Testing Documentation:

Contractors are NOT required to submit testing documentation with quotes;

however, the Contracting Officer reserves the right to request actual copies of test reports at any time before or after award.

5. Environmental Documentation:

a. Provide certification for Indoor Air Quality (GREENGUARD or equivalent), if available.

b. Provide documentation regarding recycled content and recyclability for all products submitted, if available.

6. Warranty Documentation:

a. Provide any additional or extended warranty that exceeds manufacturer’s standard warranty; extended warranty shall be clearly stated on manufacturer’s letterhead and include a verifiable digital signature containing encryption or handwritten signature, date, and title of the company official accepting technical responsibility.

b. Refer to item descriptions for specific warranty requirements by product type.

1.1.2 Non-Conforming RFQ Response

Submittal of product brochures shall not be acceptable in place of technical documentation or construction specifications. Submittal of a general price list containing large amounts of items not relevant to the procurement is not acceptable. Extended warranties shall not be typed onto the manufacturer’s current warranty. Submittals not in compliance with Section 1.1.1 of the FID shall be considered non-conforming and declined.

1.2 Submittal and Clarifications Format

The RFQ shall be submitted via electronic communications as stated in Section 1.1.1.

The technical supporting documentation shall be submitted in a searchable Adobe Acrobat (PDF) document and organized and bookmarked by item number of the FID.

Embedded objects, i.e. embedded links, files, images within clarification responses, shall be considered non-conforming.

1.3 Post Award Submittal

Documentation shall be submitted to the end user 6 weeks after post award meeting, and shall include the following information:

1. Product information as listed in Section 1.1.1.1

2. Warranty documentation as listed in Section 1.1.1.7

3. Care and maintenance instructions for each item

4. List of manufacturers with a Point of Contact for every item awarded

5. 8” x 11” Sample boards with actual fabrics/finishes organized by item number

Attachment #2 Page 7 of 70

2.0 Contractor General Notes

1. All products proposed to be installed within one room or suite shall consist of items of one style and finish. All products shall be free of rough or sharp edges. Proposed products shall include all components necessary to provide a complete and stable unit. Items shall have consistent quality standards as described and required in the

FID.

2. Although such work is not specifically indicated, furnish and install all supplementary or miscellaneous items, appurtenances, and devices incidental to, or necessary for, sound, secure, and complete installation of all items, including but not limited to built-in equipment.

3. Awarded contractor is responsible for verifying all existing field conditions i.e.

including, but not limited to, built-in opening requirements and electrical conditions.

4. All wood casegoods and wood seating in a common suite or in the same room shall have identical veneer and finish process to ensure complete match in finish and sheen level. A custom match shall be required with a benchmark sample for approval by IMCOM Interior Design G9. Coloration of the sample shall be within industry standards. All samples shall be submitted after award and prior to order.

5. All metal/laminate desks and storage shall be from the same manufacturer.

6. Provide end user with a full color way with a minimum of three options of different patterns solid and/or textured textiles and varying colored fabrics within the same manufacturer or graded in range for selection after award.

7. Where equivalent fabric and finishes have been proposed, bidders shall provide actual samples or color images and specifications for the alternate fabric or finish.

The Government retains the right to reject any alternates not equal to the required specification.

8. All fabric and finish selections shall be approved by the end user after award and prior to order.

9. Exposed storage backs not located against walls shall be fully finished.

10. Contractor shall provide soft casters and field verify floor material after award.

11. Seat width and depth shall be measured using the CMD (Chair Measurement

Device) protocol, where applicable. Seat width shall be measured from the widest outer points of the seat. Seat depth shall be measured from the most forward point of the back lumbar to the front edge of the seat. Overall height shall be measured from the finished floor to the top of the backrest.

12. If the CMD (Chair Measurement Device) protocol is not used, seat width measurement shall be the dimension between arms, seat depth shall be measured from the front of the seat to the front of the backrest and overall height shall be measured from the finished floor to the top of backrest.

13. Items, including internal working parts and components, requiring power shall be compatible with the building power supply. Contractor shall confirm required power supply voltages and hertz after award and prior to order.

14. Contractor shall provide transportation and installation of major equipment per manufacturer’s recommendation, including but not limited to ironers and forklifts.

15. Contractor shall provide training for the end-user.

Attachment #2 Page 8 of 70

END OF SECTION

Attachment #2 Page 9 of 70

3.0 Mattresses

Warranty Requirements:

1. 10/10 Non-Prorated Warranty

2. Manufacturer shall include a law label on each mattress. The required warranty code shall be clearly and accurately printed on the label.

Testing and Standards:

All mattresses shall meet the following testing requirements, minimum:

ASTM 1566-99

STP 603-08

STP604-08

STP606-08

General Requirements:

1. All mattress and box spring/foundation sets are subject to an industry standard variance of +/- ½”

2. All sets shall be 16 CFR 1633 compliant

3. Wire edge shall be 9 gauge steel, minimum (if used)

3.1 Item No. MQ-2: Mattress, Queen

Overall Dimensions: 60”W x 80”D x 10-½ - 11-½”H

Required product line:

Sealy – Claybrook Plush, #SL 510147-QU

a. 1-Sided mattress

b. Mattress shall be plush

c. Handles on sides of the mattress

d. Innerspring:

i. Heavy gauge steel coils, 638 density minimum

ii. Industry standard encased coil or open coil systems

e. Durable fabric cover:

i. Shall have Nano-Tex stain-resistant treatment embedded into the fabric cover

ii. Shall be stain and water resistant

iii. Antimicrobial

f. Edge support: High performance foam encased edge

g. Border: Fire retardant fiber to match mattress

h. Quilting:

i. Fire retardant fiber

ii. Poly foam or equivalent for promotion of cooler sleep

iii. Core support layer: Reinforced center foam for added support

i. Primary Insulation: Heavy duty insulator pad or similar support layer

Attachment #2 Page 10 of 70

j. Upholstery: Poly foam or equivalent

Finish:

a. Fabric cover: Manufacturer’s standard selection shall include white damask

3.2 Item No. MQ-1: Mattress, Queen

Overall Dimensions: 60”W x 80”D x 10-½ - 11-½”H

Sealy – Cardiff Firm, #SL 510156-QU

a. 2-Sided mattress

b. Mattress shall be firm

c. Handles on sides of the mattress

d. Innerspring:

i. Heavy gauge steel coils, 513 density minimum

ii. Industry standard encased coil or open coil systems

e. Durable fabric cover

f. Edge support: High performance foam encased edge

g. Border: Fire retardant fiber to match mattress

h. Quilting:

i. Fire retardant fiber

ii. Poly foam or equivalent for promotion of cooler sleep

iii. Core support layer: Reinforced center foam for added support

i. Primary Insulation: Heavy duty insulator pad or similar support layer

j. Upholstery: Poly foam or equivalent

a. Fabric cover: Manufacturer’s standard selection shall include white damask

3.3 Item No. MT-1: Mattress, Twin

Overall Dimensions: 39”W x 75”D x 10-½ - 11-½”H

*Item shall be the same as Item MQ-1, except for the following:

Sealy – Cardiff Firm, #SL 510147-TW

4.0 Foundations

Warranty Requirements:

1. 10/10 Non-Prorated Warranty

2. Manufacturer shall include a law label on each mattress. The required warranty code shall be clearly and accurately printed on the label.

Attachment #2 Page 11 of 70

Environmental and Sustainability:

1. Foundation shall be made from certified sustainable wood

Testing and Standards:

All box springs shall meet the following testing requirements, minimum:

ASTM 1566-99

STP 603-08

STP604-08

STP606-08

1. All mattress and box spring sets are subject to an industry standard variance of +/-

½”

2. All sets shall be 16 CFR 1633 compliant

4.1 Item No. FQ-2: Foundation, Queen

Overall Dimensions: 60”W x 80”D x 7”H

Required product lines:

Sealy – Hospitality Grade Foundation, #SL 610147-QU

a. Recyclable all wood foundation

b. Durable fabric cover

c. Shall be 7”H

d. Shall be from the same line or collection as MQ-2

a. Fabric cover: Manufacturer’s standard selection shall include white damask to match mattress

4.2 Item No. FQ-1: Foundation, Queen

Overall Dimensions: 60”W x 80”D x 9”H

Sealy – Hospitality Grade Foundation, #SL 610156-QU

a. Recyclable all wood foundation

b. Durable fabric cover

c. Shall be 9”H

d. Shall be from the same line or collection as MQ-1 and MT-1

Attachment #2 Page 12 of 70

a. Fabric cover: Manufacturer’s standard selection shall include white damask to match mattress

4.3 Item No. FT-1: Foundation, Twin

Overall Dimensions: 39”W x 75”D x 9”H

*Item shall be the same as FQ-1, except for the following:

Sealy – Hospitality Grade Foundation, #SL 610156-TW

5.0 Bed Bases

1. Limited lifetime warranty

1. Panels shall be constructed of solid 18-22 gauge steel

5.1 Item No. BQ-1: Bed Base, Queen

Overall Dimensions: 60”W x 72”D x 7-1/2”H

Researched product lines:

Mantua – Weshco #J75MB50, or equal Leggett and Platt – Pedestal Bed Base, Queen, 650 Black

a. Panel sides shall have 18-22 gauge steel construction

b. Rust proof finish

c. Minimum of three cross supports, tubular, heavy duty steel or angle iron, with center legs

d. No tool assembly

a. Metal: Manufacturer’s standard powder coated, rust proof finish shall include black

5.2 Item No. BF-1: Bed Base, Full

Overall Dimensions: 53”W x 72”D x 7-1/2”H

Researched product lines:

Mantua – Weshco #J75MB46, or equal Leggett and Platt – Pedestal Bed Base, Full, 646 Black, or equal

a. Panel sides shall have 18-22 gauge steel construction

Attachment #2 Page 13 of 70

b. Rust proof finish

c. Minimum of three cross supports, tubular, heavy duty steel or angle iron, with center legs

d. No tool assembly

a. Metal: Manufacturer’s standard powder coated, rust proof finish shall include black

6.0 Metal/Laminate Desks – NOT USED

7.0 Metal Furniture: Lateral Files and Storage Towers/Cabinets– NOT USED

8.0 Laminate Tables, Metal Bases – NOT USED

9.0 Laminate Training Tables – NOT USED

10.0 Wood Casegoods – Europe

1. 5 years, minimum

1. Work surfaces shall be fully supported by floor-standing pedestals or other supports such as brackets, legs, panels, etc., following the manufacturer’s standard practices for the size, type and placement. Size and placement of supports shall not interfere with kneespace clearances. All pedestals and supports shall be indicated on the drawings and in the component listing.

2. Transitional wood casegoods blend the light, clean lines of contemporary styling with the influence of traditional period styling without appearing heavy or bulky. Elements such as base molding or trim (if present), crown molding or cornice/profiled trim, and work surface edge details may be simpler than their traditional counterparts and may be curvilinear or rectilinear in design. They may also be smaller than traditional moldings and have a smaller projection from the face of the piece on which they are applied. Ornamentation such as picture mold or other overlay moldings are not appropriate to this style.

3. All wood desk components and wood storage components within a room shall be from the same manufacturer.

4. All casegood components located throughout an entire building shall have a consistent finish and color.

5. The finish color shall match on all components within a room.

6. All wood shall be of the same species, except contrasting wood species shall be permitted for decorative accents and inlays.

7. All desk and storage components shall have adjustable glides with a minimum adjustment of 5/8”, except for mobile desks and nightstands. Nightstands may have fixed nylon glides.

Attachment #2 Page 14 of 70

8. Provide all brackets and hardware to ensure proper installation and stability of products.

9. Clips, brackets, screws, and other construction and attachment elements shall be concealed.

Veneer Components:

1. Veneers shall be “natural”. “Composite” or “reconstituted veneer” shall not be acceptable.

2. Drawer fronts shall have a vertically matched veneer within each pedestal set.

3. Veneer thickness shall be 1/40” minimum. Veneer shall be 7-ply minimum.

4. All segments in one panel shall be the same size, except the two outside edge segments can be narrower to visually balance the panel. Any cathedral grain pattern shall be centered within the flitch.

5. All veneer plates on one panel shall come from the same flitch of veneer;

mismatched plates shall be considered non-conforming.

6. The grain direction on exterior panels, including doors and drawers, shall be vertical, with cathedral peaks pointed toward the top of the panel.

7. Wood veneer surfaces shall be bonded to the core with a PVA or other low VOC adhesive utilizing either a hot or cold press process to ensure complete lamination to the core.

8. Products shall be available in “semi-open pore” or “full-fill” finishes.

9. No unfilled worm holes, spike knots, veneer patches, bark pockets, torn grain, open splits, rough cuts, or ruptured grain shall be permitted on exposed surfaces, except as otherwise noted below.

Premium Visibility Surface Requirements:

1. Premium visibility surfaces include the following:

a. Drawer and door fronts

2. Wood veneer for these surfaces shall conform to the following requirements:

a. Plain-sliced (flat-cut)

b. Cathedrals shall be centered in segment

c. Split heart shall be permitted if a man-made cathedral is achieved

d. Cathedrals with wild grain that deviate from the desired arc shape shall be minimal and shall have less than four concave (opposite the cathedral direction) points per cathedral line

e. The average sapwood content for cherry and walnut veneer shall be from 0-5%, with no more than 20% maximum on any individual furniture item. Sapwood areas shall be treated and toned to be uniform in color with adjacent heartwood areas

f. Slight color and/or mineral streaks that run parallel to the grain shall be permitted

g. Slight color variation with no sharp contrast shall be permitted

h. Veneer shall be book or slip matched

i. Minimum nominal segment width shall be 5”

j. Conspicuous pin knots shall be ¼” maximum diameter with the dark portion no greater than ⅛” diameter; conspicuous burls shall be ⅜” diameter maximum.

Attachment #2 Page 15 of 70

Average combined quantity shall not exceed 10 per 32 sq.ft. for maple and 24 per 32 sq.ft. for cherry and walnut

k. Birdseye in maple shall be scattered with no clusters

l. Slight sugar in maple shall be permitted. Sugar streaks shall be parallel to the grain and shall be lighter than the darkest cathedral

m. Occasional sound and scattered gum spots in cherry shall be permitted

n. Slight worm tracks parallel to the grain and lighter than the darkest cathedral shall be permitted

o. Occasional vine marks and cross bars shall be permitted

p. Bull’s eye shall not be permitted in walnut

q. A maximum of two repaired hairline splits no larger than 1/16” x 6” shall be permitted

r. Small blending repairs shall be permitted

High Visibility Surface Requirements:

1. High visibility surfaces include the following:

a. Exterior face of modesty panels and overhead storage end panels

b. Exterior ends of overhead storage cabinets, wardrobe and storage cabinets

2. Wood veneer for these surfaces shall conform to the following requirements:

a. Plain-sliced (flat-cut)

b. Cathedrals shall be centered in segment

c. Split heart shall be permitted if a manufactured cathedral is achieved

d. Cathedrals with wild grain that deviate from the desired arc shape shall be permitted and shall have less than four concave (opposite the cathedral direction) points per cathedral line

e. The average sapwood content for cherry and walnut veneer shall be from 0-5%, with no more than 20% maximum on any individual furniture item. Sapwood areas shall be treated and toned to be uniform in color with adjacent heartwood areas

f. Color and/or mineral streaks that run parallel to the grain shall be permitted.

Mineral streaks in maple shall be blending

g. Slight color variation with no sharp contrast shall be permitted

h. Veneer shall be slip matched

i. Minimum nominal segment width shall be 3”

j. Conspicuous pin knots shall be ¼” maximum diameter with the dark portion no greater than ⅛” diameter; conspicuous burls shall be ½” maximum diameter.

Average combined quantity shall not exceed 10 per 32 sq.ft. for maple and 64 per 32 sq.ft. for cherry and walnut

k. Scattered sound and repaired knots shall be permitted. Sound knots shall be ⅜” maximum diameter; repaired knots shall be ⅛” maximum diameter. The combined average number shall be no more than 4 per 32 sq.ft.

l. Birdseye in maple shall be permitted; clusters shall not be heavy

m. Occasional sugar in maple shall be permitted. Sugar streaks shall be parallel to the grain and shall be lighter than the darkest cathedral

n. Occasional sound and scattered gum spots and streaks in cherry shall be

Attachment #2 Page 16 of 70

o. Slight worm tracks parallel to the grain and lighter than the darkest cathedral shall be permitted

p. Vine marks and cross bars shall be permitted

q. Bull’s eye shall be permitted in walnut

r. A maximum of four repaired hairline splits no larger than ⅛” x 8” shall be permitted

s. Slight rough cut/ruptured grain shall be permitted

t. Blending repairs shall be permitted

Moderate Visibility Surface Requirements:

1. Moderate visibility surfaces include the following:

a. Interior face of modesty panels and both faces of overhead storage end panels

b. Interior faces and shelves of bookcases

c. Interior of overhead storage cabinets, wardrobes and storage cabinets

2. Wood veneer for these surfaces shall conform to the following requirements:

a. Plain-sliced (flat-cut)

b. Split heart shall be permitted

c. 20% sapwood shall be permitted for cherry and walnut. Sapwood areas shall be treated and toned to be uniform in color with adjacent heartwood areas

d. Color and/or mineral streaks that run parallel to the grain shall be permitted.

Mineral streaks in maple shall be blending

e. Color variation with some contrast shall be permitted

f. Veneer shall be slip matched

g. Minimum nominal segment width shall be 3”

h. Conspicuous burls and pin knots in cherry and walnut shall be permitted

i. Birdseye in maple shall be permitted

j. Sugar in maple shall be permitted. Sugar streaks shall be parallel to the grain and shall be lighter than the darkest cathedral

k. Scattered sound and repaired knots less than ½” diameter shall be permitted.

The combined average number shall not exceed 8 per 32 sq.ft.

l. Gum spots in cherry shall be permitted

m. Few bark pockets not to exceed ¼” x 2” shall be permitted

n. Worm tracks in cherry and walnut shall not be permitted

o. Vine marks and cross bars shall be permitted

p. Bull’s eye shall be permitted in walnut

q. A maximum of four repaired hairline splits no larger than ⅛” x 8” shall be

r. Slight rough cut/ruptured grain shall be permitted

Solid Wood Components: (Visible components only)

1. Solid wood components shall be kiln dried with moisture content from 5-10%.

2. All solid wood shall be compatible for color and grain.

3. Unlimited sound, scattered birdseye in maple shall be permitted.

4. Sound knots shall be no more than ¼” in diameter.

5. Mineral stain shall not exceed 10% of the face.

6. Sapwood in cherry and walnut shall be less than 5% of the face.

Attachment #2 Page 17 of 70

7. Worm holes less than 1/16” shall be permitted.

8. No bark pockets, honeycomb, pitch pockets or streaks, sticker discoloration, mineral stain, or shake shall be allowed.

Component Construction:

1. All casegood components, except for tops, shall be constructed of a solid plywood cores with veneer on exposed faces and a backer sheet on unexposed faces.

2. Desks and other products with chassis construction shall be assembled using tenon

& groove or equal construction methods, and be reinforced with hardwood cleats or a similar method of reinforcement.

3. Back panels on freestanding storage cabinets shall be let into the sides so that no raw edges are visible.

4. Tops and ends of storage units shall be securely connected with metal fasteners and hardwood biscuits.

Drawers:

1. Drawer fronts shall be solid wood or a veneered plywood panel. Veneered drawer fronts shall be completely finished on all edges, and edges shall have the same final top coat as the desk.

2. Drawers shall be 5-sided with a separate, removable front for field replacement without disturbing the contents of the drawer.

3. Drawer sides and backs shall be minimum 7/16” thick plywood assembled with dowels. Variance from the thickness requirement for file drawer sides shall only be permitted when the metal file rails attached to the top drawer edge require the dimension to be less. In no instance shall the thickness of the drawer side be reduced to less than 3/8”.

4. Drawer bottoms shall be a 3-ply construction of solid plywood, with a veneer or melamine face and a backer sheet on the underside of the panel. Drawer bottoms shall be let into all sides of the drawer with a rabbet joint, glued and stapled.

5. Drawers shall have heavy duty ball bearing slides.

6. Drawers of a composite core miter-fold construction, laminated with vinyl material, shall be considered non-conforming.

Work surfaces and Tops:

1. Work surfaces and tops shall be constructed of a Grade M2 or M3 particleboard or a 45 lb. medium density fiberboard core or plywood with a minimum VGS General Purpose Grade High Pressure Laminate on the face and a backer material on the underside.

2. Laminates shall be bonded to the core with a PVA adhesive in a cold press or hot press process to prevent separation of the laminate from the core.

3. Low pressure laminate and thermally fused laminate shall be considered non-conforming.

Attachment #2 Page 18 of 70

4. Surfaces with high pressure laminate finish shall have laminate on the exposed face and backer material on the unexposed face for balanced panel construction.

Thermally fused melamine surfaces shall have the same material on both faces

5. Work surfaces shall be connected to the chassis/pedestals with steel angle brackets or a similar method of attachment.

6. Work surfaces and tops shall have hardwood edges with profiles or a solid wood edge band. Species of edge shall match the species of veneer used on the work surface, except solid maple shall be acceptable in lieu of solid cherry edges.

7. All visible and exposed work surface perimeters shall have consistent profiles.

8. Wood grain direction shall run parallel to the front edge of the worksurface.

Back Panels & Modesty Panels, Side Panels and Supports:

1. Modesty panels shall be available for work surfaces.

2. End panels shall be capable of supporting the work surface without modesty or back panels.

3. End panels shall be ¾-1” and shall be constructed of a solid plywood core with veneer on exposed faces and a backer sheet on unexposed faces.

4. Back panels shall be 1/8” minimum and shall be constructed of a solid plywood core with veneer on exposed faces and a backer sheet on unexposed faces.

5. Back panels shall be recessed to allow space for electrical plugs and cords.

6. Bottom panels shall be ¾” minimum and shall be constructed of a solid plywood core with veneer on exposed faces and a backer sheet on unexposed faces.

Overhead Storage Units:

1. The minimum height from the work surface to the bottom of the hutch shall be 18”.

2. Shall be securely attached to work surfaces with industrial grade double-stick tape.

Freestanding Storage:

1. Doors shall have concealed European style hinges with a minimum opening of 95 degrees.

2. Storage cabinet and bookcase shelves shall be adjustable on 1½” centers.

3. The interior cabinet depth of wardrobes shall accommodate a coat rod for shoulder-out hanging of garments using standard coat hangers, except when required depth is less than 24”.

4. Wardrobe or storage cabinets in modular desk assemblies shall match the combined total height of the adjacent return or credenza plus the overhead storage unit.

5. Drawer fronts shall have a vertically matched veneer within each pedestal set.

Task Lighting:

1. Task lights shall be a standard component of the manufacturer's furniture products.

2. Task lights shall recess into the bottom of overhead cabinets and shelves or be shielded by a valance or trim board to fully conceal the fixture.

3. Task lights shall be sized to provide even illumination.

Attachment #2 Page 19 of 70

4. Electronic ballasts shall be provided to eliminate fluorescent lamp flicker and computer screen interference. Shared ballasts shall not be used.

5. Task lights shall provide glare control.

6. Task lights shall have an easily accessible on-off switch.

7. Daisy chain cords shall be available for the modular connection of shelf lights.

8. Fluorescent lamps shall be Energy Star rated.

9. All fixture diffusers, grilles or other coverings shall be easily removable to permit cleaning and replacement.

10. Task lights shall be UL listed and labeled.

Trim and Moldings:

1. All trim moldings shall be solid hardwood. Shaped, veneer- wrapped MDF components shall be considered non-conforming.

2. Crown/Cornice molding or profiled trim shall be securely attached with glue and concealed mechanical fasteners. Where molding or trim wraps the sides of a piece, corners shall be mitered and joints shall be tight, flush and glued for stability.

10.1 Item No. HB-5: Wall Hung Headboard, Full Size, Wood Veneer

Overall Dimensions: 60-61”W x 2-3”D x 23-24”H

a. Headboard shall accommodate a 54”W x 74”L mattress and boxspring

b. Headboard shall be wood with eased edges and corners; no sharp edges allowed

c. Top of headboard shall be arched

d. Arched, raised ½”H panel in the center of the headboard

e. Hardware for wall mount shall be included on male/female cleats, 30”W minimum

f. One cleat shall be factory installed in the same location on each headboard

Transitional Edge Detail/Molding:

Researched product lines:

New England Woodcraft – Abenaki 8800, #8816(C), or equal Thomasville – Custom Hospitality Line, or equal

Item image is for general illustration purposes only, and it is not an exact representation of the requirement.

Attachment #2 Page 20 of 70

a. Top Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

c. Raised Panel Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

d. End Panel Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel, if available

a. Wood Veneer: Birch in manufacturer’s standard stain selection shall match Wilsonart

Biltmore Cherry 7924-7 Formica 7288-58 Ginger Root Maple or equal

10.2 Item No. HB-2: Wall Hung Headboard, Queen Size, Wood Veneer Overall Dimensions: 66-67”W x 2-3”D x 23-24”H

a. Headboard shall accommodate a 60”W x 80”L mattress and boxspring

b. Headboard shall be wood with eased edges and corners; no sharp edges allowed

c. Top of headboard shall be arched

d. Arched, raised ½”H panel in the center of the headboard

e. Hardware for wall mount shall be included on male/female cleats, 40”W minimum

f. One cleat shall be factory installed in the same location on each headboard

Transitional Edge Detail/Molding:

a. Top Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Researched product lines:

New England Woodcraft – Abenaki 8800, #8817(C), or equal

Attachment #2 Page 21 of 70

c. Raised Panel Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

d. End Panel Front Edge Detail: Manufacturer’s standard transitional profile selection

a. Wood Veneer: Birch in manufacturer’s standard stain selection shall match Formica

7288-58 Ginger Root Maple or equal

10.3 Item No. HB-3: Wall Hung Headboard, Queen Size, Wood Veneer Overall Dimensions: 66-67”W x 2-3”D x 23-24”H

*Item shall be the same as HB-2, except for the following:

Finish:

a. Wood Veneer: Birch in manufacturer’s standard stain selection shall match Wilsonart

Biltmore Cherry 7924-7 Formica 7288-58 Ginger Root Maple or equal

10.4 Item No. HB-4: Wall Hung Headboard, Queen Size, Wood Veneer

Overall Dimensions: 66-67”W x 2-3”D 23-24”H

*Item shall be the same as HB-2, except for the following:

Finish:

a. Wood Veneer: Birch in manufacturer’s standard stain selection shall match Wilsonart

Tuscan Walnut 7921-38 or equal

10.5 Item No. NS-5: Night Stand, Small, Laminate/Wood Veneer

Overall Dimensions: 23”W x 19-20”D x 24-25”H

a. High pressure laminate bow front top with solid hardwood edges

Researched product lines:

New England Woodcraft – Abenaki 8800, #8810-2C or equal

Attachment #2 Page 22 of 70

i. Top shall be replaceable

b. Bowed drawer front

c. (1) 5-6”H Operable drawer

d. Recessed back

e. (1) Fixed shelf

f. Flared legs with glides

g. Wood veneer closed panels shall be located along the back, sides and bottom of the nightstand

h. Wood veneer arched apron between legs on front and sides

Transitional Edge Detail/Molding:

include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

c. End Panel Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel, if available

d. Base Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

a. High Pressure Laminate: Manufacturer’s standard selection shall include Wilsonart

Biltmore Cherry 7924-7 Formica 7288-58 Ginger Root Maple or equal

b. Wood Veneer: Birch in manufacturer’s standard stain selection shall match HPL top

c. Pulls: Manufacturer’s standard transitional selection shall include black brushed nickel

10.6 Item No. NS-1A: Night Stand, Small, Laminate/Wood Veneer Overall Dimensions: 20”W x 21-22”D (Curved top) x 24-25”H

Researched product lines:

New England Woodcraft – Abenaki 8800, #2310-20 or equal

Attachment #2 Page 23 of 70

i. Top shall be replaceable

b. Top, drawer front, fixed shelf and plinth base shall be bowed

c. (1) 8”H Operable drawer

d. Recessed back

e. (1) Fixed shelf

f. Wood veneer plinth base with glides

g. Wood veneer closed panels shall be located along the back, sides and bottom of the include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

c. End Panel Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel, if available

d. Base Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

a. High Pressure Laminate: Manufacturer’s standard selection shall include Formica

7288-58 Ginger Root Maple or equal

b. Wood Veneer: Birch in manufacturer’s standard stain selection shall match HPL top

c. Pulls: Manufacturer’s standard transitional selection shall include brushed nickel

10.7 Item No. NS-1C: Replacement Top for Night Stand, Small, Laminate/Wood Veneer Overall Dimensions: 18”W x 19-20”D

General Requirements:

a. High pressure laminate bow front top with solid hardwood edges

b. Style and finish shall match item NS-4

Transitional Edge Detail/Molding:

a. Top Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

a. High Pressure Laminate: Manufacturer’s standard selection shall include Wilsonart

Tuscan Walnut 7921-38 or equal

10.8 Item No. NS-1D: Replacement Top for Night Stand, Small, Laminate/Wood Veneer Overall Dimensions: 30”W x 20-21”D

Attachment #2 Page 24 of 70

a. High pressure laminate bow front top with solid hardwood edges

b. Style and finish shall match item NS-3

Transitional Edge Detail/Molding:

a. Top Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

a. High Pressure Laminate: Manufacturer’s standard selection shall include Wilsonart

10.9 Item No. NS-1E: Replacement Top for Night Stand, Small, Laminate/Wood Veneer Overall Dimensions: 20”W x 21-22”D

Contractor shall:

*Coordinate with end user and field verify replacement top style and dimensions after award and prior to order.

General Requirements:

a. High pressure laminate bow front top with solid hardwood edges

b. Style and finish shall match existing item in the field.

Transitional Edge Detail/Molding:

a. Top Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

a. High Pressure Laminate: Manufacturer’s standard selection shall include Wilsonart

10.10 Item No. NS-3: Night Stand, Large, Laminate/Wood Veneer Overall Dimensions: 30”W x 20-1/2”D x 24-25”H

Researched product lines:

New England Woodcraft – Abenaki 8800, #8810-2C or equal

Attachment #2 Page 25 of 70

i. Top shall be replaceable

b. Bowed drawer fronts

c. (2) Operable drawers

d. Recessed back

e. Flared legs with glides

f. Wood veneer closed panels shall be located along the back, sides and bottom of the

g. Wood veneer arched apron between legs on front and sides include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

a. High Pressure Laminate: Manufacturer’s standard selection shall include Wilsonart

Tuscan Walnut 7921-38 or equal

c. Pulls: Manufacturer’s standard transitional selection shall include black

10.11 Item No. NS-4: Night Stand, Small, Laminate/Wood Veneer Overall Dimensions: 18”W x 19-1/2”D x 24-25”H

Researched product lines:

New England Woodcraft – Abenaki 8800, #8810-2A or equal

Attachment #2 Page 26 of 70

i. Top shall be replaceable

b. Bowed drawer fronts

c. (2) Operable drawers

d. Recessed back

e. Flared legs with glides

f. Wood veneer closed panels shall be located along the back, sides and bottom of the

g. Wood veneer arched apron between legs on front and sides include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

a. High Pressure Laminate: Manufacturer’s standard selection shall include Wilsonart

Tuscan Walnut 7921-38 or equal

10.12 Item No. W-1: Wardrobe Storage Cabinet, Laminate/Wood Veneer Overall Dimensions: 36”W x 28-29”D (Curved top), 24-24 ½”D (Sides) x 72”H

Researched product lines:

New England Woodcraft – Abenaki 8800, #89216, or equal

Attachment #2 Page 27 of 70

a. High pressure laminate bow front top with solid wood edge

b. (2) Full height, wood doors

i. Doors shall be flat, without molding

c. Full width coat road and fixed high pressure laminate top shelf

d. (2) Adjustable, laminate bottom shelves

i. Shelves shall be mounted at 12” and 24” above the bottom of the wardrobe

e. Wood veneer flat toe-kick

f. Recessed back

g. (4) Adjustable glides

h. Wood veneer closed panels shall be located along the sides and back of the wardrobe

i. Style, detailing and finish shall match W-1, HB-2, NS-1A include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include flat edge

c. End Panel Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel, if available

d. Base Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

a. High Pressure Laminate: Manufacturer’s standard selection shall include Formica

7288-58 Ginger Root Maple or equal

10.13 Item No. W-1A: ADA Wardrobe Storage Cabinet, Laminate/Wood Veneer

Attachment #2 Page 28 of 70

Overall Dimensions: 36”W x 28-29”D (Curved top), 24-24 ½”D (Sides) x 72”H

b. (2) Full height, wood doors

i. Doors shall be flat, without molding

c. Full width coat road and fixed high pressure laminate top shelf

i. Coat rod shall be mounted 48” above the bottom of the wardrobe

ii. Fixed shelf shall be mounted 51-52” above the bottom of the wardrobe

d. Wood veneer flat toe-kick

e. Recessed back

f. (4) Adjustable glides

g. Wood veneer closed panels shall be located along the sides and back of the

h. Style, detailing and finish shall match W-1, HB-2, NS-1A include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include flat edge

c. End Panel Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel, if available

d. Base Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel

Finish:

Researched product lines:

New England Woodcraft – Abenaki 8800, #89216, or equal

Attachment #2 Page 29 of 70

a. High Pressure Laminate: Manufacturer’s standard selection shall include Formica 7288-58 Ginger Root Maple or equal

10.14 Item No. W-2: Wardrobe Storage Cabinet, Laminate/Wood Veneer Overall Dimensions: 36”W x 28-29”D x 72”H

b. (2) Full height, flat wood doors with applied molding

c. Full width coat road and fixed high pressure laminate top shelf

d. (2) Adjustable, laminate bottom shelves

i. Shelves shall be mounted at 12” and 24” above the bottom of the wardrobe

e. Wood veneer bowed toe-kick

f. Recessed back

g. (4) Adjustable glides

h. Wood veneer closed panels shall be located along the sides and back of the

i. Style, detailing and finish shall match W-1, HB-2, NS-1A include reverse bevel

b. Top Side Edge Detail: Manufacturer’s standard transitional profile selection shall include flat edge

c. End Panel Front Edge Detail: Manufacturer’s standard transitional profile selection shall include reverse bevel, if available

Researched product lines:

New England Woodcraft – Abenaki 8800, #89216(AM), or equal

Attachment #2 Page 30 of 70

d. Base Edge Detail: Manufacturer’s standard…