W912DS-15-B-0016-0002.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

30-105-04EXCEPTION TO SF 30

APPROVED BY OIRM 11-84

STANDARD FORM 30 (Rev. 10-83) Prescribed by GSA

FAR (48 CFR) 53.243

The purpose of this amendment is to:

1) Incorporate Revised Draw ings & Specifications,

2) Incorporate Revised Bid Schedule (See revised CLIN 0002),

3) Incorporate Revised Bid Notes (See revised note #8),

4) Reissue the Table of Contents,

5) Incorporate Q&A's (FOR INFORMATIONAL PURPOSES ONLY)

6) Incorporate revised Wage Rates NJ150027, dated 09/11/2015, NJ27

7) Incorporate Site Visit Sign in Sheet

The Bid Due Date remains the same on Thursday, 24-September-2015 at 2PM EST.

1. CONTRACT ID CODE PAGE OF PAGES

J 1 30

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

16C. DATE SIGNED

BY 17-Sep-2015

16B. UNITED STATES OF AMERICA15C. DATE SIGNED15B. CONTRACTOR/OFFEROR

(Signature of Contracting Officer)(Signature of person authorized to sign)

8. NAME AND ADDRESS OF CONTRACTOR (No., Street, County, State and Zip Code) X W912DS-15-B-0016

X 9B. DATED (SEE ITEM 11)

25-Aug-2015

10B. DATED (SEE ITEM 13)

9A. AMENDMENT OF SOLICITATION NO.

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

X The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offer is extended, X is not extended.

Offer must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing Items 8 and 15, and returning 1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN

REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE

CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(B).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

10A. MOD. OF CONTRACT/ORDER NO.

2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO.(If applicable)

6. ISSUED BY

3. EFFECTIVE DATE

17-Sep-2015

CODE

US ARMY CORPS OF ENGINEERS, NEW YORK

26 FEDERAL PLAZA, RM 1843

NEW YORK NY 10278-0090

W912DS 7. ADMINISTERED BY (If other than item 6)

4. REQUISITION/PURCHASE REQ. NO.

CODE

See Item 6

FACILITY CODECODE

EMAIL:TEL:

W912DS-15-B-0016

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

The following items are applicable to this modification:

AMENDMENT 0002

NOTE: Bidders must acknowledge receipt of this amendment by the date specified in the bid (or as amended) by one of the following methods: In the space provided on the SF 1442, by separate letter, or by signing block 15 below. FAILURE TO ACKNOWLEDGE AMENDMENT BY THE DATE AND TIME SPECIFIED MAY

RESULT IN REJECTION OF YOUR BID IN ACCORDANCE WITH THE LATE BID, LATE

MODIFICATION OF BID, OR LATE WITHDRAWAL OF BID (FAR 14.304).

SECTION 00 10 00 - SOLICITATION/CONTRACT FORM

The offeror acceptance period has increased by 30 from 90 to 120.

REVISED BID SCHEDULE 9-17-15

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

0001 1 Job

RENOVATE & REPAIR BLDG 2415 -NAF PORTION

FFP

Provide all labor, equipment, appliances, and materials, and furnish and perform all work in strict accordance with the specifications, schedules, and drawings forming parts thereof, subject to the terms and conditions of the contract to renovate and repair building 2415 as indicated in the contract documents as the NAF portion of the project except for items below.

FOB: Destination

MILSTRIP: W16ROE51745420

NET AMT

0002 1 Job

RENOVATE & REPAIR BLDG 2415 -APF PORTION

Provide all labor, equipment, appliances, and materials, and furnish and perform all work in strict accordance with the specifications, schedules, and drawings forming parts thereof, subject to the terms and conditions of the contract to renovate and repair building 2415 as indicated in the contract documents (Plans and Specification) for the Auto Hobby Shop, APF portion of the project.

0003 1 Job $75,000.00 $75,000.00

FINAL RECORD DRAWING – NAF

FFP

All work for the Final Record Drawing Submission (See paragraph 10 of Section 00 73 00). NAF Portion of the project.

0004 1 Job $25,000.00 $25,000.00

FINAL RECORD DRAWING – APF

All work for the Final Record Drawing Submission (See paragraph 10 of Section 00 73 00).

APF Portion of the project.

0005 1 Job

OPTION

OPTION 1: EXTERIOR APF PORTION

FFP

Provide all labor, equipment, appliances, and materials, and furnish and perform all work in strict accordance with the specifications, schedules, and drawings forming parts thereof, subject to the terms and conditions of the contract to renovate and repair building 2415 as indicated in the contract documents as the Exterior APF portion of the project to include but not limited to Exterior Insulation and Finish System (EIFS), doors, windows, pavement and fencing.

0006 1 Job

OPTION

OPTION 2: INSTALLATION OF BRICK VENEER

FFP

Provide all labor, equipment, appliances, and materials, and furnish and perform all work in strict accordance with the specifications, schedules, and drawings forming parts thereof, subject to the terms and conditions of the contract to renovate and repair building 2415 as indicated in the contract documents as part of the APF portion of the project. In lieu of EIFS, install Brick Veneer and cast stone exterior as shown in the contract documents. NOTE: this cost shall include only the difference between the Brick/Cast stone and EIFS.

0007 50 Cubic OPTION Yard

OPTION 3: REMOVAL & DISPOSAL OF CONCRETE

FFP

Removal and disposal of unknown concrete, including excavation and backfill.

NAF Portion of the project.

0008 100 Cubic OPTION Yard

OPTION 4: HAND DIGGING

FFP

Hand digging around unidentified/unmarked utilities, if found.

0009 100 Linear OPTION Foot

OPTION 5: FIX BROKEN UTILITY LINE

FFP

Fix broken 4" to 6" diameter unidentified/unmarked utility line.

TOTALS

TOTAL BASE (CLINs 0001 thru 0004) $

TOTAL OPTIONS (CLINs 0005 thru 0009) $

GRAND TOTAL (BASE + OPTIONS ) (CLINs 0001 thru 0009) $

NOTES

1. Bidders are required to bid on the Base Bid and all Optional Bid Items or their bids will be rejected.

2. Bidders are reminded that they must bid on the issued plans and specifications as amended. Any deviations, conditions or attachments made by the bidder himself thereto may render the bid non-responsive and be cause for its rejection.

3. Line Item Numbers 0003 and 0004 are pre-priced at $75,000.00 and $25,000.00 respectively, it’s a firm fixed line item, and the price shown may not be changed. See paragraph 10 of Section 00 73 00.

4. Option #2: if the cost represents savings it shall be clearly noted in parenthesis, i.e.

5. The Basis of evaluation will be the lowest responsive/responsible bidder calculated based on values of each CLIN: Base Bid (sum of CLIN 0001 thru 0004) plus sum of Options Numbers 1, 3, 4 & 5 (CLINs 0005, 0007, 0008, 0009), Option Number 2 (CLIN 0006) will be added/subtracted following notation in note 5 above.

6. Options #1 thru #5 may be exercised, at the Government’s discretion, within 210 calendar days from the date the contractor received the Notice to Proceed. Exercise of any or all options will not alter the project completion date of the contract. The Government is under no obligation to award any Optional Item.

7. Bid Acceptance Period: Bids are valid for 120 calendar days for bid acceptance from the Bid Opening Due Date.

Responses to bidder inquiries are provided "for information purposes only" and do not revise the solicitation, plans or specifications.

TO OFFORERS

The following changes shall be made to the drawings and specifications.

DRAWINGS

1. The following DRAWINGS have been REVISED but NOT REISSUED:

- Drawing C-501 – add the following note to BITUMINOUS CONCRETE PAVEMENT detail:

“Contractors shall follow NJDOT specifications for bituminous section. Specifications can be found at: http://www.state.nj.us/transportation/eng/specs/2007/spec400.shtm”

- Drawing S-001 – replace note 2.02 in its entirety with the following: “A registered professional Geotechnical Engineer shall verify condition and/or adequacy of all subgrades, fills and backfills before placement of foundations, footings, slabs, walls, fills, backfills, etc. Compact earth below new foundation to 95% modified proctor, min.”

- Drawing S-102 – Replace TOTAL DECK THICKNESS in FLOOR DECK PROPERTIES table to read as follows: “ 5 ½” ”

- Drawing AD-101 – Replace comment jest below column line “E” relating to relocation of equipment with the following: “All equipment will be moved by the owner prior to commencement of construction, inclusive of barrels and oil talks (free standing).”

- Drawing A-601 – revise Performance Level, within DOOR SCHEDULE, for all doors with Performance Level 4 to Performance Level 3.

- Drawing A-601 – add the following comment to DOOR SCHEDULE for door 108: “Storefront door and frame.”

- Drawing MD-101 – add the following to KEYED NOTE 14: “The riser for the gas service shall be extended to clear the brick veneer.”

- Drawing P-101 – Replace comment between column line B & C relating to hose reels with the following: “Hose Reels provided and installed by the contractor, to be selected to meet the requirements of the system. Refer to appendix A for reel used as basis of design.”

- Drawing P-701 – revise Note 1 as follows: “Pre and Post filter shall be selected appropriately so that it fits the air dryer properly with particle removal down to 1 micron and coalesced liquid.”

- Drawing P-701 – add Note 2 as follows: “The existing facility uses Hankison HPR35 air dryer using 115V/1 ph/60hz electrical service, same or approved equal may be used.”

2. The following DRAWINGS have been REVISED and REISSUED:

Drawing S-101

Drawing A-103

Drawing A-201

Drawing A-202

Drawing A-203

Drawing A-301

Drawing A-302

Drawing A-310

Drawing I-401

Drawing E-001

Drawing ED-101

Drawing E-101

Drawing E-102

Drawing E-111

Drawing E-501

Drawing E-502

Drawing E-601

Drawing E-602

Drawing E-603

3. The following DRAWINGS have been ADDED:

None

SPECIFICATIONS

1. The following SPECIFICATION SECTIONS have been ADDED and are provided in their entirety herein:

-Appendix A – Basis of Design Info.

-Site Visit Sign In Sheet

2. The following SPECIFICATIONS SECTIONS have been DELETED in their entirety:

Section 26 05 73 – Covercurrent Protective Device Coordination Study – is hereby deleted in its entirety without replacement.

3. The following SPECIFICATIONS SECTIONS have been REVISED and REISSUED:

TABLE OF CONTENT – TOC is hereby reissued in its entirety.

4. The following SPECIFICATIONS have been REVISED but NOT REISSUED:

- Section 00 10 00 – Solicitation/Contract Form – (Bid Schedule) – Revise Item No 0002 Description as follows: “Provide all labor, equipment, appliances, and materials, and furnish and perform all work in strict accordance with the specifications, schedules, and drawings forming parts thereof, subject to the terms and conditions of the contract to renovate and repair building 2415 as indicated in the contract documents (Plans and Specification) for the Auto Hobby Shop, APF portion of the project.”

- Section 00 10 00 – Solicitation/Contract Form – (Bid Schedule) – Revise Note 8 (Bid Acceptance Period) from 90 calendar days to 120 calendar days.

- Section 08 71 00 – Door Hardware – replace description of hardware set #2 with the following:

“1 Saddle/Weather stripping at bottom of door to prevent air infiltration. All hardware not listed here to be furnished by door manufacturer. And to be keyed to match facility locks.”

- Section 23 09 00 – Instrumentation and Control for HVAC – revise paragraphs 2.2.D.1 and 2.2.D.2 as follows: “NOT USED.” Revise paragraph 2.2.D.3 as follows: “Building lighting control system specified in Section 260923 "Lighting Control Devices." Revise paragraph 2.2.D.3 as follows: “Fire alarm system specified in Section 283176 "Interior Fire Alarm and Mass Notification System.”

- Sections 26 27 26, 27 13 00, 27 15 00 – replace all references within these sections from Category 5e to Category 6.

- Section 27 13 00 – Communications Backbone Cabling –replace references wherever they appear in this section from EIA/TIA 568-B to EIA/TIA 568-C and TIA/EIA 569-A to TIA/EIA 569-D

- Section 27 13 00 – Communications Backbone Cabling –replace references to TIA/EIA-568- B.1 / B.2 within paragraphs 1.3(A), 3.4(B)(1) & 3.4(C)(1) with TIA/EIA 569C.

- Section 27 15 00 – Communications Horizontal Cabling –replace references wherever they appear in this section from EIA/TIA 568-B to EIA/TIA 568-C and TIA/EIA 569-A to TIA/EIA 569-D

- Section 27 15 00 – Communications Horizontal Cabling – replace all references to TIA/EIA- 568-B.1 / B.2 within this section to TIA/EIA 568-C.

- Section 27 15 00 – Communications Horizontal Cabling – replace paragraph’s 2.4.B Description as follows: “100-ohm, 4 pair, category 6, UTP covered with a thermoplastic jacket.”.

Change reference in pars. 2.4.B.3, 2.5.C & 3.7 to Category 6, in lieu of Category 5e.

BIDDER’S QUESTIONS AND GOVERNMENT REPLY

1. Please provide a table of contents for Divisions 21, 22, 23, 26, 27, 28, etc. so we can confirm we have all specifications sections. Response: The revised TOC is hereby reissued in this amendment #2 to include all specifications sections.

2. Sheet P-701, Compressed Air, indicates hose reels, 14 on Room 0100 and 4 in Room 0300. The drawing indicates 15 cfm per location or a total of 270 cfm, plus tire break and bread blaster which are unknown cfm’s. The existing air compressor is shown as 24 cfm and this is an insufficient cfm for this application. Kindly provide proper flow rates available. Response: The compressor is to remain as shown on the plans.

3. Ingersoll Rand manufacturer is specified for pre and post filters F-1441 Grade 6 which does not exist.

Typically a pre-filter is –G rated for flow and post filter is –H rated for flow. Please provide proper part numbers and flow rates. Response: The note is here by revised in this amendment.

4. The specified air drier, Ingersoll Rand D-421-T rated for 25 cfm does not appear to be sized properly for this application. Model number is incorrect; please provide correct model number and voltage desired. Response: Ingersoll Rand D-421-T was used as the basis of design and it was found to be adequate during the design phase. The existing system uses Hankison HPR35 air dryer using 115V/1 ph/60hz electrical service, same or approved equal can be used.

5. Kindly confirm if the owner will be providing the holes reels in absence of a specification. Response:

The contractor shall provide hose reel that's compatible with compressor requirements.

6. See attached fax we received from Nu-Age Films requesting approval for a substitute product for spec 072600 “Vapor Retarders” (total of 4 pages). Response: At this time we are not in the stage of reviewing detail and specific products. This will be addressed at the time of shop drawing review.

7. Sheet AD101 has a note to ‘vacate all equipment’. For equipment that is to be moved to storage, where is the owner providing storage? Response: The equipment will be moved before construction begins.

8. During the site visit on September 10th, existing oil and antifreeze disposal tanks were located in the building. Who is responsible for the removal and disposal of these tanks? Response: If you're talking about the barrels and tank they will be removed before construction begins.

9. The west of the workbays 300 area there is an adjacent existing structure which is visible in the aerial photo on sheet G-001. The structural and architectural drawings including those associated with demolition do not address that building. Sheet A-203 even shows a new exterior wall for building 2415 at that location. What is the connection detail to that building, or will it be demolished by others prior to the start of this contract? Response: The building will be demolished before construction. The existing block wall will be left it shall have brick veneer as the rest of the building.

10. Specification section 05 12 00 paragraph 1.7.b calls for ACSE certified erection of the steel. Only a small portion of steel erectors are ACSE certified and as a result there will be a significantly higher erection cost. Can the ACSE certification be waived for the erection? Response: No, Certification will not be waived.

11. Line item 0005 Option 2 states that it is to include ‘the APF portion…’. Is this line supposed to read ‘the Exterior APF portions….’? Response: This line item is self explanatory, only the difference between EFIS and brick veneer is to be included in this item.

12. There are items listed as APF on the documents that are not associated with ‘the fire detection, reporting, and suppression system’ that line item 0002 lists. These items include asbestos abatement and lead paint removal. Under what line item are interior non-fire related APF items to be included?

Response: Please refer to contract drawings for complete and detailed designation of NAF and APF funded work. NAF funded work is included in CLIN 0001 and APF funded work is included in CLIN 0002.

13. Is the CMU backup on the exterior walls to be considered APF or non APF funded? Response: It is NAF funded. Only the exterior finishes and insulation… are included in APF (see description of Option 1, CLIN 0005 and refer to drawings for further guidance.)

14. Is the work associated with the Covered Storage Area, considered to be APF funded? Response:

Please refer to drawings for explanation and designation of APF and NAF funded work.

15. Sheet F001 Note 12 calls for the installation of a post indicator valve exterior to the building, but no waterline work is shown exterior to the building and the plan notes regarding pipe connection, show connection to existing at a flange within the building. Does a post indicator valve need to be installed on the existing water service? Response: Please refer to sheet F-101 keyed note 3 & 4.

16. Sheet P101 has 18 ‘hose reels indicated for coordination’ but sheet P701 depicts the hose reels without such a mark. Are these hose reels included within this contract, and if so what are the requirements for them? Response: Yes the hose reels are included in the scope of contractors work. Please refer to drawing P-701 the reel is depicted with a box just before the ½” quick connection.

17. What raceway is required for controls cabling in exposed spaces? Response: Please refer to Appendix A for raceway details.

18. What raceway is required for telecommunications cabling in exposed spaces? Response: Please refer to Appendix A for raceway details.

19. Will plenum rated cabling be acceptable for controls and telecommunications in concealed spaces?

Response: Yes, the specification allows plenum rated cables to be used.

20. Specification 23 09 00 paragraph 2.2.d states that the control system is to include building intrusion, building lighting, and the fire alarm/mass notification system. However, no other portion of specification 23 09 00, any other specification, or the plans, provides for how these systems are to be interconnected in the digital control system. Are these systems to be integrated into the building HVAC control system, and if so, what are the specifications for the integration, programming, and reporting? Response: Please refer to spec section 230900 2.2 D 3 indicating the lighting controls, (260923) are included; BAS is also included. Also note section 230900 para 2.3.

21. The existing gas service, meter, and riser exterior to the building are within the dimensions of the planned for brick veneer. What is the detail for the brick veneer at the gas riser? Response: The meter and riser will have to be extended to clear brick veneer.

22. Sheet E-001 General Note 12 calls for the contractor to provide 1” conduit with pull string, while sheet E801 suggests that the wiring is installed under this contract. Is this contract to provide telecommunications wiring from the telecommunications room to the jacks? Response: Yes, wiring is to be included as part of the construction cost.

23. Is the equipment shown on sheet E801 for Room 211 to be provided under this contract? Response:

Provide patch panel etc. as shown on the drawing.

24. No lightning protection system is indicated on the plans or specifications. Is a lightning protection system required for either the Auto Hobby Shop and/or the Storage Building? Response: No, none is required at either building.

25. There is a section 260573 Overcurrent Protective Device Coordination Study included within the specifications. The electric service to the building is existing to remain, and the plans are detailed about the new panels and the circuiting. In addition, paragraph 1.5.b.1 calls for the government to perform this study. How does this specification relate to this contract? Response: The referenced specification section is hereby deleted in this amendment.

26. If telecommunications cabling is to be provided under this contract, plans and specifications list both CAT 5e and CAT 6, what type cabling is to be provided? Response: Specifications are hereby revised to only include CAT6 cabling.

27. The overhead coiling doors are listed in specification 08 33 23 to be sheet thickness of 0.028 inches, which is standard construction, but the door schedule on sheet A601 calls out for level 4 doors which would require a sheet thickness of 0.067 inches, which is maximum duty. What gage thickness is required for the overhead coiling door? Response: The coiling overhead doors shall be Level 3, Drawing A601 is hereby revised.

28. The door schedule on sheet A601 calls for all exterior doors and many interior doors to be level 4 maximum duty. This level is not even referenced in section 08 11 13 and appears to not fit the function of the building. What is the required performance levels for the steel doors and frames?

Response: All doors with performance level 4 shall be revised to performance level 3 in this amendment.

29. The schedule on sheet A601 has door 108 as a hollow metal door in an aluminum frame. What is the required door and frame material for Door 108? Response: The 108 door shall be aluminum storefront door and frame.

30. Reference is made to specification section 122113 "Horizontal Louver Blinds". Section 1.3, Action Submittals subparagraph F refers to the window treatment schedule on drawings. There does not appear to be a window treatment schedule on the drawing within the bid documents. Please provide the necessary drawing or information so that this section can be properly priced. Response: For window treatment finish legend please refer to sheet I-601, WB1

31. Are the existing light ballasts to be assumed as PCB containing or PCB free? Response: That information is not available at this time. It will have to be determined in the field.

32. Detail A6/S302 shows an existing masonry wall being dowelled to an existing footer. To accomplish this dowelling as detailed is not feasible as the embedment location is potentially up to 9’ below the top of the existing CMU. What is required in lieu of this detail? Response: The details will remain as is, the contractor may submit at time of construction and alternative to be approved by the government during shop drawing review process.

33. Specification 087100 hardware set 2 lists the use of a Pemko 2705 T threshold at the overhead doors. The Pemko 2705 T threshold is designed for and sized to be used at hinged exit doors. Since this is not the correct application what, if anything, is required for hardware set #2 at the overhead coiling doors? Response: The Pemko 2705 T is hereby replaced with saddle/weather stripping at bottom of door to prevent max air infiltration.

34. Specification 122113 was provided for horizontal blinds, and a product was listed on the plans in the finish schedule. However, there is no callout in plan, detail or on the window schedule for these to be installed anywhere. Where are window blinds to be installed? Response: Please refer to drawing I-601 for finish schedule (WB-1) and see I-401 for locations.

35. Sheet I-001 lists GFCI equipment. New vehicle lifts are listed as being installed by the contractor.

Can information on the lifts be provided? Response: At this time the only the information included on the drawing is available.

REVISED WAGES 9-11-15

General Decision Number: NJ150027 09/11/2015 NJ27

Superseded General Decision Number: NJ20140027

State: New Jersey ke 9/11/2015

Construction Type: Building

County: Burlington County in New Jersey.

BUILDING CONSTRUCTION PROJECTS (does not include single family homes or apartments up to and including 4 stories).

Note: Executive Order (EO) 13658 establishes an hourly minimum wage of $10.10 for 2015 that applies to all contracts subject to the Davis-Bacon Act for which the solicitation is issued on or after January 1, 2015. If this contract is covered by the EO, the contractor must pay all workers in any classification listed on this wage determination at least $10.10 (or the applicable wage rate listed on this wage determination, if it is higher) for all hours spent performing on the contract. The EO minimum wage rate will be adjusted annually. Additional information on contractor requirements and worker protections under the EO is available at www.dol.gov/whd/govcontracts.

Modification Number Publication Date 0 01/02/2015 1 01/23/2015 2 02/27/2015 3 03/20/2015 4 03/27/2015 5 06/05/2015 6 06/12/2015 7 07/31/2015 8 08/28/2015 9 09/11/2015

ASBE0014-003 05/01/2015

BURLINGTON COUNTY (City of Beverly; Townships of Cinnaminson, Delanco, Delron, Edgewater Park, Evesham, Hainesport and Lumberton; Borough of Maple Shade; Township of Medford; Borough of Medford Lakes; Townships of Moorestown and Mt. Laurel;

Borough of Palmyra; Township of Riverside; Borough of Riverton;

Townships of Shamong, Southampton, Tabernacle, Westhampton and Willingboro)

Rates Fringes

ASBESTOS WORKER/HEAT & FROST

INSULATOR (Includes the application of all insulating materials, protective coverings, coatings and finishings to all types of mechanical systems; also, the application of firestopping material to openings and penetrations in walls, floors, ceilings and curtain walls; also, all lead abatement).......................$ 44.44 31.65

ASBE0089-003 07/02/2013

BURLINGTON COUNTY (Townships of Bordentown, Burlington, Chesterfield, Easthampton, Florence, Mansfield, Mt. Holly, New Hanover, North Hanover, Pemberton, Springfield and Woodland)

ASBESTOS WORKER/HEAT & FROST

INSULATOR ((includes the application of all insulating materials, protective coverings, coatings and finishings to all types of mechanical systems; also, the application of firestopping material to openings and penetrations in walls, floors, ceilings and curtain walls; also, all lead abatement))......................$ 40.32 30.18

PAID HOLIDAYS:

The last day prior to the Christmas and New Year's Day observed holiday: 4 hrs. pay.

BRNJ0002-013 05/01/2014

Rates Fringes

Bricklayer.....................$ 38.25 28.26

Work on high stacks: 22% per hour additional.

BRNJ0007-012 07/01/2013

Marble setter...................$ 55.32 28.39

BRNJ0007-014 07/01/2014

Rates Fringes

TERRAZZO WORKER/SETTER...........$ 48.88 32.18

BRNJ0007-017 06/01/2013

Rates Fringes

Tile finisher..................$ 39.56 22.60 Tile setter....................$ 45.16 27.20

Tile finisher:

Work grouting all epoxy: $10.00 additional per day.

CARP0006-009 11/01/2014

Rates Fringes

CARPENTER (Scaffold Builder).....$ 43.74 56%

The first sixty feet at the regular rate, 10% per hour additional for each additional fifty feet thereafter.

CARP0006-010 11/01/2014

Rates Fringes

CARPENTER

Including Acoustical Ceiling Installation, Drywall Hanging, Formwork, Batt and Blown Insulation...$ 43.74 56%

CARP0029-006 11/01/2014

Rates Fringes

Soft floor layer...............$ 43.74 56%

CARP0454-009 05/01/2013

PILEDRIVERMAN....................$ 39.65 29.12

PAID HOLIDAYS:

New Year's Day, Washington's Birthday, Memorial Day, Independence Day, Labor Day, Thanksgiving Day and Christmas Day; provided that the worker works any of the three days in the five-day work week preceding the holiday and the first work day after the holiday.

CARP0715-007 05/01/2014

Rates Fringes

Millwright.....................$ 43.88 56%

Work of erection and dismantling of elevators and towers, such as concrete conveyors and temporary material elevators, scaffolding or other structures to be used as scaffolding inside or outside of buildings: the first sixty feet at the regular rate, 10% per hour additional for each additional fifty feet thereafter.

ELEC0269-017 03/01/2015

BURLINGTON COUNTY (north of a line following the west and south limits of Burlington Borough from the Delaware River, in a southeasterly direction, to the Burlington - Mt. Holly road;

then, south-southeast along the Burlington - Mt. Holly road to the town of Mt. Holly, includes Mt. Holly; then, east along the Pennsylvania Railroad to the town of New Lisbon, includes New Lisbon; then, continuing along the Pennsylvania Railroad to the Ocean County line)

Electrician and cable splicer (Includes Low Voltage Wiring)....$ 48.57 61.48%

ELEC0351-001 09/29/2014

ATLANTIC COUNTY; BURLINGTON COUNTY (south of a line following the west and south limits of Burlington Borough from the Delaware River, in a southeasterly direction, to the Burlington

- Mt. Holly road; then, south-southeast along the Burlington - Mt. Holly road to the town of Mt. Holly, does not include Mt.

Holly; then, east along the Pennsylvania Railroad to the town of New Lisbon, does not include New Lisbon; then, continuing along the Pennsylvania Railroad to the Ocean County line);

CAMDEN, CAPE MAY, CUMBERLAND, GLOUCESTER AND SALEM COUNTIES:

Electricians:

Cable splicer on lead cable.$ 46.51 72.54% + .65 Electrician and cable splicer.....................$ 44.51 75.35% + .65

ELEV0005-004 01/01/2015

Rates Fringes

Elevator mechanic..............$ 51.62 28.385

PAID HOLIDAYS:

New Year's Day, Memorial Day, Independence Day, Labor Day, Veteran's Day, Thanksgiving Day, the Friday after Thanksgiving Day, and Christmas Day.

PAID VACATION:

Employer contributes 2% of basic hourly rate as vacation pay credit for 6 months to 5 years of service, and 4% for 5 years or more of service.

ENGI0825-020 07/01/2015

Rates Fringes

Power equipment operators:

GROUP 1.....................$ 47.70 28.65

GROUP 2.....................$ 45.48 28.65

GROUP 3.....................$ 43.57 28.65

GROUP 4.....................$ 41.94 28.65

GROUP 5.....................$ 40.23 28.65

Hazardous waste removal work:

Work on a state or federally designated hazardous waste site, where the worker is in direct contact with hazardous material, and when personal protective equipment is required for respiratory, skin and eye protection: 20% per hour additional.

New Year's Day, Washington's Birthday observed, Memorial Day, Independence Day, Labor Day, Presidential Election Day, Veteran's Day, Thanksgiving Day and Christmas Day; provided

1) that the worker works three of the preceding five work days before the holiday; or, the work day before the holiday and the work day after the holiday; and, 2) that the worker works the work day before and the work day after the holiday.

DEFINITION OF GROUPS:

GROUP 1:

Backhoe, Including Backhoe Track; Boom; Concrete Paving Machine; Crane (all types, including overhead and straddle traveling type); Drill (down-the-hole drill, rotary drill, self-propelled hydraulic drill, self-powered drill);

Elevating Grader; Excavator; Front End Loader (5 cu. yd.

and over); Piledriver (length of boom, including length of leads, shall determine premium rate applicable); Trencher

GROUP 2:

Backhoe Loader Combo; Concrete Pumper; Grader/Blade (Finish);

Hoist; Hydraulic Crane, 10 Tons and under; Front End Loader (2 cu. yd. but less than 5 cu. yd.); Scraper; Side Boom

GROUP 3:

Asphalt Spreader; Bulldozer;Compressor(2 or 3) (in Battery) (within 100 ft.); Forklift; Front End Loader (1 cu. yd.

and over but less than 2 cu. yd.); Lull; Mechanic; Paver, Asphalt; Roller, Blacktop; Tractor;

GROUP 4:

Bobcat/Skid Loader; Compressor (Single); Farm Tractor; Front End Loader (under 1 cu. yd.); Hydroseeder; Roller, Grade;

Pump, Hydraulic

GROUP 5:

Oiler

IRON0068-011 07/01/2015

(Lumberton)

Rates Fringes

IRONWORKER

Reinforcing.................$ 43.90 20.78 Structural and Ornamental...$ 45.89 20.78

IRON0350-009 07/01/2015

BURLINGTON COUNTY (south and east of a line starting from the point on the Atlantic-Burlington county line where the

Atlantic-Burlington county line crosses Route 206; then, following a line northeast through Wharton State Park to the town of Chatsworth; then, continuing along the same line, to the Burlington-Ocean county line)

Ironworkers:

Reinforcing.................$ 45.77 28.75 Structural and Ornamental...$ 46.77 28.75

IRON0399-005 07/01/2015

BURLINGTON COUNTY (north and west of a line starting from the point on the Atlantic-Burlington county line where the Atlantic-Burlington county line crosses Route 206; then, following a line northeast through Wharton State Park to the town of Chatsworth; then, continuing along the same line, to the Burlington-Ocean county line)

IRONWORKER (Structural, Reinforcing and Ornamental)......$ 44.60 27.25

LABO0008-001 05/01/2011

Rates Fringes

Asbestos Removal Laborer.........$ 28.37 21.62

The removal, abatement, enclosure and decontamination of personal protective equipment, chemical protective clothing and machinery relating to asbestos and/or toxic and hazardous waste or materials which shall include but not necessarily be limited to: the erection, moving, servicing and dismantling of all enclosures, scaffolding and barricades; the operation of all tools and equipment normally used in the removal or abatement of asbestos and toxic or hazardous waste or materials; the labeling, bagging, cartoning, crating, or other packaging of materials for disposal; the clean-up of the worksite; and all other work incidental to the removal, abatement, encapsulation, enclosure, and decontamination of asbestos and toxic or hazardous waste or materials; and, in addition, all work tasks involved in the maintenance and operation of energy resource recovery plants (co-generation plants)

LABO0222-006 07/01/2012

LABORER

MASON TENDER:

Brick/Cement/Concrete.......$ 29.85 23.07

LABO0222-008 07/01/2012

Rates Fringes

Laborers:

Asphalt Shoveler, Asphalt Spreader, Landscape Laborer, Pipelayer, Power Toole Operator and Screedman...................$ 29.35 23.07

PAIN0021-032 05/01/2015

BURLINGTON COUNTY (south of a line drawn between these cities:

Florence to Bustleton to Columbus to Jobstown to Pemberton to Ongs Hat to Chatsworth to Whiting to Pinewald to Ocean Gate to Seaside Heights)

Glazier........................$ 40.60 26.25

Work at 30 ft. above the working surface, or on a swing stage: $1.00 per hour additional.

PAIN0711-011 05/01/2014

BURLINGTON COUNTY (north of a line drawn between these cities:

Florence to Bustleton to Columbus to Jobstown to Pemberton to Ongs Hat to Chatsworth to Whiting to Pinewald to Ocean Gate to Seaside Heights)

Glazier........................$ 41.61 20.46

Work welding or using a cutting torch: $1.00 per hour additional.

Work on a swing stage scaffold; on a pipe scaffold providing the working height of the platform is 30 ft. or above; and on motorized lifts provided that the height of the lift platform is above the second floor or above thirty feet:

$1.00 per hour additional.

PAIN0711-018 05/01/2014

Rates Fringes

DRYWALL FINISHER/TAPER...........$ 38.00 20.35

PAIN0711-019 05/01/2014

Rates Fringes

PAINTER (Brush & Roller).........$ 37.72 20.19 PAINTER (Spray)..................$ 40.28 19.98

PLAS0592-036 05/01/2015

Rates Fringes

CEMENT MASON/CONCRETE FINISHER...$ 39.17 31.06

PLUM0009-015 07/01/2014

BURLINGTON COUNTY (north of a line drawn from the town of Burlington City, includes Burlington City; then, along County Road Route 541 East, also known as High St., until it reaches the city of Mt. Holly, includes the city of Mt. Holly; then, along Madison Ave. in Mt. Holly to State Road Route 38 East;

then, along State Road Route 38 East until it crosses over State Road Route 206 and becomes County Road Route 530; then, along County Road Route 530 to Magnolia Road, includes Pemberton Borough; then, south on Magnolia Road in Pemberton Township to Magnolia New Lisbon Road (Route 545); then, south on Mt. Holly Misery Road to State Road Route 70 East; then, along State Road Route 70 East to the Ocean County line)

PIPEFITTER (Including HVAC Pipe Installation)...............$ 44.78 33.70 Service and Repair..........$ 34.93 14.41 PLUMBER (Excluding HVAC Pipe Installation)....................$ 44.78 33.70 Service and Repair..........$ 34.93 14.41

* PLUM0322-008 05/01/2015

BURLINGTON COUNTY (south of a line drawn from the town of

Burlington City, does not include Burlington City; then, along County Road Route 541 East, also known as High St., until it reaches the city of Mt. Holly, does not include the city of Mt.

Holly; then, along Madison Ave. in Mt. Holly to State Road Route 38 East; then, along State Road Route 38 East until it crosses over State Road Route 206 and becomes County Road Route 530, does not include Pemberton Borough; then, south on Magnolia Road in Pemberton Township to Magnolia New Lisbon Road (Route 545); then, south on Mt. Holly Misery Rd. to State Road Route 70 East; then, along State Road Route 70 East to the Ocean County line)

PIPEFITTER (Including HVAC Pipe Installation)...............$ 44.02 34.84 PLUMBER (Excluding HVAC Pipe Installation)....................$ 44.02 34.84

ROOF0030-027 05/01/2015

Rates Fringes

Roofer

SHINGLES....................$ 25.00 18.02

SLATE AND TILE..............$ 28.00 18.02

ALL OTHER WORK..............$ 33.65 28.15

Mopper, and operator of felt-laying machine: $.50 per hour additional.

Work applying roofing material, on any new construction job, on those days on which a felt-laying machine or slag dispensing machine is used: $.50 per hour additional.

PAID HOLIDAY:

The last working day before Christmas, to be paid at the rate of four hours pay.

SFNJ0669-006 04/01/2015

Rates Fringes

SPRINKLER FITTER (Fire Sprinklers)......................$ 47.15 21.96

SFNJ0692-002 05/01/2013

Within 15 miles beyond the city limits of Philadelphia.

Sprinkler fitter (Fire Sprinklers)......................$ 48.65 21.57

SHEE0027-009 06/01/2012

Rates Fringes

SHEET METAL WORKER (Including HVAC Duct Installation)..........$ 43.08 32.52

TEAM0469-003 05/01/2015

BURLINGTON COUNTY (east of a line drawn from the New Jersey Turnpike to the Delaware River)

Truck drivers:

Dump Truck..................$ 37.75 29.09 Off the Road Truck..........$ 37.60 29.09

Hazardous waste removal work:

Work on a state or federally designated hazardous waste site, where the worker is in direct contact with hazardous material, and when personal protective equipment is required for respiratory, skin and eye protection: $3.00 per hour additional.

Work on a state or federally designated hazardous waste site, in a zone requiring Level A personal protection for any workers other than the truck driver: $3.00 per hour additional.

Work on a state or federally designated hazardous waste site where the worker is not working in a zone requiring Level A, B or C personal protection: $1.00 per hour additional.

New Year's Day, President's Day, Decoration Day, Independence Day, Labor Day, Presidential Election Day, Veteran's Day, Thanksgiving Day and Christmas Day.

VACATION PAY CREDIT:

Workers working or receiving pay for 80 days within a year receive one week paid vacation (48 hours); 125 days receive two weeks paid vacation (96 hours); 145 days receive 15 days paid vacation (120 hours); 15 years seniority and 145 days receive 4 weeks paid vacation (160 hours).

TEAM0676-002 05/01/2015

BURLINGTON COUNTY (west of a line drawn from the New Jersey Turnpike to the Delaware River)

Truck drivers:

Dump Truck Drivers..........$ 32.20 23.485 Off the Road Truck..........$ 32.55 23.485

Hazardous waste removal work:

Work on a state or federally designated hazardous waste site, where the worker is in direct contact with hazardous materials, and when personal protective equipment is required for respiratory, skin and eye protection: $3.00 per hour additional.

Work on a state or federally designated hazardous waste site, where personal protection A, B, C or D is NOT required:

$1.00 per hour additional.

SHIFT WORK:

An owner mandated irregular shift staring any time other than between 6:00 am and 8:00 am to receive $1.00 per hour, for each hour worked, in addition to the regular rate of pay.

PAID HOLIDAYS:

New Year's Day, President's Day, Memorial Day, Independence Day, Labor Day, Presidential Election Day, Veteran's Day (or the day after Thanksgiving, at the option of the contractor), Thanksgiving Day, the afternoon of the day before Christmas (Dec. 24) provided that the worker works in the morning, and Christmas Day, provided that the worker works or is available for work on at least two days in the week in which the holiday occurs.

BEREAVEMENT PAY:

In case of a death in the worker's immediate famiy (mother, father, wife, husband, children, brother, sister, current mother-in-law, current father-in-law, grandparents), the worker shall be allowed leave not to exceed three (3) days straight-time pay, provided that he or she shall receive no pay unless the day of death and the burial day falls on a regular work day, and not on days off, holidays, vacation, Saturdays or Sundays.

SUNJ2004-003 01/02/2009

Rates Fringes

LABORER: Common or General......$ 19.27 12.42

PLASTERER........................$ 42.33 0.00

WELDERS - Receive rate prescribed for craft performing operation to which welding is incidental.

Unlisted classifications needed for work not included within the scope of the classifications listed may be added after award only as provided in the labor standards contract clauses (29CFR 5.5 (a) (1) (ii)).

The body of each wage determination lists the classification and wage rates that have been found to be prevailing for the cited type(s) of construction in the area covered by the wage determination. The classifications are listed in alphabetical order of "identifiers" that indicate whether the particular rate is a union rate (current union negotiated rate for local), a survey rate (weighted average rate) or a union average rate (weighted union average rate).

Union Rate Identifiers

A four letter classification abbreviation identifier enclosed in dotted lines beginning with characters other than "SU" or "UAVG" denotes that the union classification and rate were prevailing for that classification in the survey. Example:

PLUM0198-005 07/01/2014. PLUM is an abbreviation identifier of the union which prevailed in the survey for this classification, which in this example would be Plumbers. 0198 indicates the local union number or district council number where applicable, i.e., Plumbers Local 0198. The next number, 005 in the example, is an internal number used in processing the wage determination. 07/01/2014 is the effective date of the most current negotiated rate, which in this example is July 1, 2014.

Union prevailing wage rates are updated to reflect all rate changes in the collective bargaining agreement (CBA) governing this classification and rate.

Survey Rate Identifiers

Classifications listed under the "SU" identifier indicate that no one rate prevailed for this classification in the survey and the published rate is derived by computing a weighted average rate based on all the rates reported in the survey for that classification. As this weighted average rate includes all rates reported in the survey, it may include both union and non-union rates. Example: SULA2012-007 5/13/2014. SU indicates the rates are survey rates based on a weighted average calculation of rates and are not majority rates. LA indicates the State of Louisiana. 2012 is the year of survey on which these classifications and rates are based. The next number, 007 in the example, is an internal number used in producing the wage determination. 5/13/2014 indicates the survey completion date for the classifications and rates under that identifier.

Survey wage rates are not updated and remain in effect until a new survey is conducted.

Union Average Rate Identifiers

Classification(s) listed under the UAVG identifier indicate that no single majority rate prevailed for those classifications; however, 100% of the data reported for the classifications was union data. EXAMPLE: UAVG-OH-0010 08/29/2014. UAVG indicates that the rate is a weighted union average rate. OH indicates the state. The next number, 0010 in the example, is an internal number used in producing the wage determination. 08/29/2014 indicates the survey completion date for the classifications and rates under that identifier.

A UAVG rate will be updated once a year, usually in January of each year, to reflect a weighted average of the current negotiated/CBA rate of the union locals from which the rate is based.

WAGE DETERMINATION APPEALS PROCESS

1.) Has there been an initial decision in the matter? This can be:

* an existing published wage determination

* a survey underlying a wage determination

* a Wage and Hour Division letter setting forth a position on a wage determination matter

* a conformance (additional classification and rate) ruling

On survey related matters, initial contact, including requests for summaries of surveys, should be with the Wage and Hour Regional Office for the area in which the survey was conducted because those Regional Offices have responsibility for the Davis-Bacon survey program. If the response from this initial contact is not satisfactory, then the process described in 2.)

and 3.) should be followed.

With regard to any other matter not yet ripe for the formal process described here, initial contact should be with the Branch of Construction Wage Determinations. Write to:

Branch of Construction Wage Determinations Wage and Hour Division U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210

2.) If the answer to the question in 1.) is yes, then an interested party (those affected by the action) can request review and reconsideration from the Wage and Hour Administrator (See 29 CFR Part 1.8 and 29 CFR Part 7). Write to:

Wage and Hour Administrator U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210

The request should be accompanied by a full statement of the interested party's position and by any information (wage payment data, project description, area practice material, etc.) that the requestor considers relevant to the issue.

3.) If the decision of the Administrator is not favorable, an interested party may appeal directly to the Administrative Review Board (formerly the Wage Appeals Board). Write to:

Administrative Review Board U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210

4.) All decisions by the Administrative Review Board are final.

END OF GENERAL DECISION

(End of Summary of Changes)