Attachment_0003_MEO_B1737B_W58RGZ-17-R-0220.pdf

MAINTENANCE ENGINEERING ORDER

(AMCOM Reg. 750-2)

MEO NO.

DATE PAGE 1 of

TITLE Tolerances Unless otherwise noted, dimensions are in inches and tolerances are:

Fractional ………………… ± 1/32 Decimal ………………... ± 0.010 Angular ………………… ± ½°

APPLICABILITY CSI Critical Characteristic Affected?

Impact Statement Attached?

REFERENCES FOR RDECOM USE ONLY

DOCUMENT(S) AFFECTED

PURPOSE OR PROBLEM

PROJECT ENGINEER ENGINEERING REVIEW ENGINEERING RELEASE

MED FORM 5-DEC-09 1401-R-E

B 1737 Rev B Sep 23, 2015 8

IUID Parts Marking for Stabilator Electro/Mechanical Linear Actuator P/N

DL2155M20 (70400-06641-117)

Technical

INTERIM USE OF THIS MEO IS AUTHORIZED

UNTIL AFFECTED DOCUMENT IS UPDATED.

MEO CHANGE TYPE

4) Normal - Can be implemented with normal priorityPRIORITY IMPLEMENTATION CATEGORY

UH60 DAA

DMWR 1-1680-332, dtd 3 May 2010 TN 140131B 8/25/2015

DOCUMENT CHANGE IS REQUIRED Verification: Hands-On Table-Top None

REV B: Corrected Part Number in Title Block.

LUU.DINH.Q

.1232215859

Digitally signed by

LUU.DINH.Q.1232215859

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=LUU.DINH.Q.1232215859 Date: 2015.09.22 14:20:24 -05'00'

NOLEN.OTIS.

F.1231157146

Digitally signed by

NOLEN.OTIS.F.1231157146

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=CONTRACTOR, cn=NOLEN.OTIS.F.1231157146 Date: 2015.08.25 09:46:07 -05'00'

Otis Nolen (Camber Corporation)

HORN.REINHOL

D.J.1087783495

Digitally signed by

HORN.REINHOLD.J.1087783495

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=HORN.REINHOLD.J.1087783495 Date: 2015.09.22 14:56:32 -05'00'

Dinh Luu Ron Horn PUBLICATION CHANGE REQUEST: REQUEST THAT THE FOLLOWING DATA BE INCLUDED IN THE NEXT

CHANGE OR REVISION TO THE PUBLICATION IDENTIFIED ABOVE.

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

iii iv

1-2

1-7.6.a

1-7.6.a.(2)

CHANGE Figure 1-2 title to read: "IUID Data Plates".

ADD "Table 3-1 IUID Life Cycle Events" to the List of Tables.

REPLACE paragraph 1-7.6.a with the following paragraph:

"a. Figure 1-2, Sheet 1 of 2, shows the possible IUID data plate options for this component. Option A represents an IUID data plate format for components originally UID-marked during production. Options A or B represents an IUID data plate format for components originally UID-marked post-production in the field or during a maintenance event (commonly referred to as legacy components)."

DELETE paragraph 1-7.6.a.(2) entirely.

Distribution Statement D:- Distribution authorized to Department of Defense and U.S. DoD contractors only to protect critical technology effective as of 26 June 2014. Other requests for this document must be referred to U.S. Army Aviation and Missile Research, Development and Engineering Center, ATTN: RDMR -AEM , Corpus Christi, TX 78419-5211

MED FORM 18 NOV 2014

W58RGZ-17-R-0220

Attachment 0003

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-2 and 1-3

1-3 and 1-4

1-3 and 1-4

1-6

1-7

1-7.7.a

1-7.7.a.(1)

1-7.7.a.(3)

1-7.7.b

1-7.7.b.(2)

1-7.7.c

1-7.7.C

1-7.7.c.(2)

1-7.7.d

1-7.7.d

1-1

INSERT "Option B" after "Sheet 2 of 2" at the end of the paragraph.

REPLACE paragraph with the following:

"(1) A Construct 1 UII shall be encoded into a 2-D data matrix using TEIs SPL (supplier’s CAGE Code) and UCN (supplier’s Unique Component Number), IAW DoD Guide to Uniquely Identifying Items and/or MIL-STD-130 and register in the DoD IUID Registry via the Wide Area Work Flow (WAWF) (App A, Websites) or AMCOM’s The Army Maintenance Management System – Aviation/Maintenance Consolidated Database System (TAMMS-A/MCDS), Unique Identification (UID) (App A, Websites). The UII can be constructed by the overhaul/repair facility using the overhaul facility's Enterprise Identifier (CAGE) SPL and UCN or the overhaul facility can generate an UII via AMCOM’s TAMMS-A/MCDS, UID database at https://tamms-a.redstone.army.mil. The component's serially-managed manufacturer serial number shall not be used to develop the UII, but shall reside as HRI on the IUID data plate."

INSERT "via the WAWF" after "registry" in the first sentence.

INSERT "Option A or B, as applicable," before "Figure 1-2" at the end of the paragraph.

CHANGE sentence to read:

"(2) The PNR 2-D data matrix shall be encoded in accordance with paragraph 1-7.7.a.(2)."

CHANGE "an IUID" in the first sentence to "a compliant IUID".

INSERT ", Option A or B, whichever is applicable." after "Sheet 2 of 2" at the end of the paragraph.

CHANGE sentence to read:

"(2) The PNR 2-D data matrix shall be encoded in accordance with paragraph 1-7.7.a.(2)."

CHANGE "an IUID" in the first sentence to "a compliant IUID".

INSERT ", Option A or B, whichever is applicable." after "Sheet 2 of 2" at the end of the paragraph.

REPLACE Figure 1-1 with new figure found on page 5 of this MEO.

REPLACE Figure 1-2 Sheets 1 and 2 of 2 with new figures found on page 6 and 7 of this MEO.

MED FORM 18 NOV 2014

B 1737 Rev B

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

3-4

3-5.2

3-5.2

3-5.2.b

3-5.2.c

3-5.2.d

3-5.2.d.(2)

3-5.2.d.(3)

3-5.2.e

3-5.2.e.(1)

3-5.2.e.(2)

CHANGE "AMCOM's TAMMS-A/UID" to read: "TAMMS-A/MCDS, UID".

ADD the following new Note after paragraph 3-5.2:

"If the stabilator electro/mechanical linear actuator arrives with an IUID data plate other than what is depicted in Figure 1-2, Sheet 1 of 2, contact cognizant AMRDEC engineering or contracting officer (COR) for replacement instructions."

CHANGE "TAMMS-A/UID" in last sentence to read: "TAMMS-A/MCDS, UID".

CHANGE "TAMMS-A/UID" to read: "TAMMS-A/MCDS, UID".

INSERT "via the WAWF" after "registry".

REPLACE paragraph 3-5.2.d.(2) with the following paragraph:

"(2) Using the human readable manufacturer serial number on the component (indicated by Serial No., Ser No., S/N, SN, SER, (S), SEQ, etc.), query the DoD IUID Registry. Select “Queries,” then “Pedigree Query.” Place the human readable manufacturer serial number in the “Serial Number” field. The query may return multiple records. Use the additional data from the component (component description, part number, etc.) to determine if one of the registry records can be matched to the component. If a registry record's data matches the component data exactly, proceed to paragraph 3-5.2.f. If no registry record can be matched exactly to the component data, proceed to paragraph 3-5.2.d.(3) below.

ADD the following new paragraph 3-5.2.d.(3):

"(3) Using the human readable manufacturer serial number on the component (indicated by Serial No., Ser No., S/N, SN, SER, (S), SEQ, etc.), query the DoD IUID Registry. Select “Queries,” then “Mark Query.” Place “SERIAL NUMBER” in the “Mark Content” field and place the human readable manufacturer serial number (as visible on component, minus any spaces) in the “Mark Value” field.

The query may return multiple records. Use the additional data from the component (component description, part number, etc.) to determine if one of the registry records can be matched to the component. If a registry record's data matches the component data exactly, proceed to paragraph 3-5-2.f. If no registry record can be matched exactly to the component data, indicate on local documents that the component was not found in the DoD IUID Registry (i.e., did not have a registered UII). A new IUID data plate(s) shall be fabricated IAW paragraph 1-7.7."

CHANGE "TAMMS-A/UID: to read: "TAMMS-A/MCDS, UID".

CHANGE "TAMMS-A" to read: "TAMMS-A/MCDS".

CHANGE "TAMMS-A/UID" in first sentence to read: "TAMMS-A/MCDS, UID".

MED FORM 18 NOV 2014

B 1737 Rev B

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

3-5

3-5

3-57

A-3

3-5.2.f.(1)

3-5.2.f.(2)

3-5.3 thru 3-5.5

3-15.at

A-8

3-1

CHANGE "TAMMS-A/UID" in first sentence to read: "TAMMS-A/MCDS, UID".

CHANGE "TAMMS-A/UID" to read: "TAMMS-A/MCDS, UID".

ADD the following paragraphs to read:

"3-5.3. IUID LIFECYCLE EVENTS (LCE)

A life cycle event specific to UID compliance is any change to the permanent status of an item i.e., lost, stolen, destroyed…, that the DOD Guide to Uniquely Identifying Items requires be reported to the DOD IUID registry. If applicable, report to the DoD IUID Registry via the WAWF (App A, Websites) or the TAMMS-A/MCDS, UID database at https://tamms-a.redstone.army.mil, the item’s change of permanent status if one of the following life cycle events in Table 3-1 occur.

3-5.4. IUID PARENT CHILD RELATIONSHIP

A parent item is an assembly, intermediate component or subassembly that has an embedded item with a Unique Item Identifier (UII) or DoD recognized UII equivalent. If applicable, upon completion of the M&O event, report component parent child relationship updates to the DoD IUID Registry via the WAWF (App A, Websites) or the TAMMS-A/MCDS, UID database at https://tamms-a.redstone.army.mil, in accordance with DoD Guide to Uniquely Identifying Items.

3-5.5. PART NUMBER CONFIGURATION CHANGE

If required, upon completion of the M&O event, the component part number configuration changes (part number roll/dash number change) that would require an addition or update of the PNR or 30P (current part number), the configuration change shall be reported to the DoD IUID Registry via the WAWF (App A, Websites) or the TAMMS-A/MCDS, UID database at https://tamms-a.redstone.army.mil."

ADD Table 3-1 found on page 8 of this MEO.

CHANGE last sentence to read:

"Refer to paragraph 1-7.8 for IUID data plate application."

REPLACE "DoD IUID Registry . . . . . . . . Department of Defense IUID Registry https://iuid.logisticsinformationservice.dla.mil" with the following:

"WAWF . . . . . . . . Wide Area Work Flow e-Business Suite https://wawf.eb.mil/"

MED FORM 18 NOV 2014

B 1737 Rev B

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

INSTRUCTION DATA PLATE

IDENTIFICATION DATA PLATE

(TYPICAL)

MODIFICATION DATA PLATE

OVERHAUL DATA PLATE

ESD WARNING LABEL

SPL XXXXX

UCN XXXXX

PNR 70400-06641-XXX

LEGACY

IUID DATA PLATE

CAG 78286

PNO 70400-06641-XXX

SEQ XXXX-XXXXX

MANUFACTURER

IUID DATA PLATE

PNR 70400-06641-XXX

DETAIL

A

A

Figure 1-1. Stabilator Actuator (Typical)

MED FORM 18 NOV 2014

B 1737 Rev B

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

NOTES:

1. If the item arrives without a registered UII, IUID data plates shall be fabricated in the format of Option B.

2. If the item arrives without IUID data plate and has a registered UII, the UII shall be replicated using the DoD IUID Registry data. The HRI displayed on IUID data plates shall be in the format of Option A or B, as applicable.

3. If the item arrives with a registered UII on compliant IUID data plates (Option A or Option B), IUID data plates shall be replicated (to configuration/format at PSA) when replacement is necessary due to damage and/or change to component data and/or configuration change e.g., part number roll (dash number change).

4. Option A: PNR application is only utilized/installed when the original part number PNO changes with a new configuration, i.e. part number roll (dash number change).

SPL XXXXX

UCN XXXXX

PNR 70400-06641-XXX

CAG 78286

PNO 70400-06641-XXX

SEQ XXXX-XXXXX

PNR 70400-06641-XXX

OPTION A (see PNR note 4) OPTION B

Figure 1-2. IUID Data Plates (Sheet 1 of 2)

MED FORM 18 NOV 2014

B 1737 Rev B

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

SPL XXXXX

UCN XXXXX

PNR 70400-06641-XXX

.50

CAG 78286

PNO 70400-06641-XXX

SEQ XXXX-XXXXX

1.50 1.50

.50

1.50

PNR 70400-06641-XXX .50

OPTION A - See Note 11 Local Fabrication)

OPTION B

(Local Fabrication)

NOTES:

1. All Dimensions in inches. Drawing not to scale.

2. Font lettering and size per MIL-STD-130. Font locations are approximate.

3. Physical characteristics and test requirements per MIL-DTL-15024, Type L.

4. Material: TESA Tape, TESA Secure 6973 PV6, matte black top layer with white under layer or an polyacrylic material equivalent.

5. The 2-D data matrix symbol shall be ECC 200 compliant in accordance with ISO/IEC 16022.

6. Quiet Zone (Free Space) around the 2-D data matrix code shall be .050 MIN. in all directions.

7. Marking edge distance to be a minimum of .060.

8. The recommended part mark size for the 2-D data matrix symbol is 0.25 to 0.50 inch square. The 2-D data matrix symbol shall not be larger that 1.00 inch square.

Option A: 2-D data matrix encoded with a Construct 1 UII using TEIs CAG

(manufacturer’s CAGE Code), PNO (manufacturer’s original part number), SEQ (manufacturer’s serial number).

Option B: The 2-D data matrix encoded with a Construct 1 UII using TEIs SPL

(supplier’s CAGE Code), UCN (supplier's item unique component number), and PNR (current part number). PNR being the Sikorsky’s or Vendor’s (if applicable) part number upon completion of the M&O event.

11. Option A: PNR application is only utilized and displayed as HRI when the original part number (PNO) changes with a new configuration, i.e. part number roll (dash number change).

9 OPTION A - See Note 11 Local Fabrication)

Figure 1-2. IUID Data Plates (Sheet 2 of 2)

MED FORM 18 NOV 2014

B 1737 Rev B

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

Table 3-1. IUID Life Cycle Events

IUID LIFE CYCLE EVENTS (LCE)

Event Definition

Abandoned

Property surrendered by a Federal agency after a written determination that the property has no commercial value, or the estimated cost of its continued care and handling would exceed the estimated proceeds from its sale. An item has no commercial value when it has neither utility or monetary value (either as useable property or as scrap)

Consumed Non-reversibly incorporated into another item Destroyed – Accident

Destroyed during a fire, natural disaster, or other unplanned natural or man-made incident

Destroyed – Combat Destroyed by the enemy during combat

Donated

Surplus property provided to a Service Educational Activity; a State, political subdivision, municipality, or tax-supported institution acting on behalf of a public airport; a public agency; a public body; a charitable institution; or any State or local government agency, and certain nonprofit organizations or institutions

Exchanged – Sold Provided to a supplier for credit Exchanged – Repair Provided to a supplier for an equivalent replacement part

Exchanged – Warranty

Provided to a supplier for an equivalent replacement part or credit while under warranty

Expended – Normal Use

Such as in the firing of a missile during combat or consumed during a manufacturing process

Expended – Experimental/Target

Such as the firing of a missile during training exercises and for testing; items destroyed while serving as a target during training exercises and tests

Leased Property that is granted to a lessee for a period of time in exchange for rent or other consideration

Loaned Owned by a DoD component and loaned to contractors, scientific institutions or other organizations

Lost Property that cannot be located or otherwise accounted for Reintroduced When an item is returned to DoD service

Retired Withdrawn from normal service; taken out of use. Includes decommissioned, stricken, sunken, transferred to AMARC/DRMS, etc.; excludes temporary idling of the item

Scrapped Waste material that will not be reused or reprocessed Sold – Other Federal

Title transferred to non-DoD Federal Agencies with compensation

Sold – State/Local Title transferred to non-Federal governmental entities with compensation

Sold – Foreign Govt.

Title transferred to non-US governmental entities with compensation

Sold – Non-Govt. Title transferred to non-governmental entities such as churches, organizations, etc. with compensation

Sold – Historic Title transferred to a museum or similar entity with compensation

Stolen Lost via theft

MED FORM 18 NOV 2014

B 1737 Rev B