Attachment_0005_-_MEO_D1093A.pdf

MAINTENANCE ENGINEERING ORDER

(AMCOM Reg. 750-2)

MEO NO.

DATE PAGE 1 of

TITLE Tolerances Unless otherwise noted, dimensions are in inches and tolerances are:

Fractional ………………… ± 1/32 Decimal ………………... ± 0.010 Angular ………………… ± ½°

APPLICABILITY CSI Critical Characteristic Affected?

Impact Statement Attached?

REFERENCES FOR RDECOM USE ONLY

DOCUMENT(S) AFFECTED

PURPOSE OR PROBLEM

PROJECT ENGINEER ENGINEERING REVIEW ENGINEERING RELEASE

MED FORM 15-DEC-09 1401-R-E

D 1093 Rev A Feb 18, 2014 5

Parts Marking for Power Transfer Unit (PTU), Hydraulic Motor/Pump Part Numbers 569774 (145HS140-8), 569775 (145HS140-9), and 569776

(145HS140-10)

Technical

INTERIM USE OF THIS MEO IS AUTHORIZED

UNTIL AFFECTED DOCUMENT IS UPDATED.

MEO CHANGE TYPE

4) Normal - Can be implemented with normal priorityPRIORITY IMPLEMENTATION CATEGORY

CH47 DAA

DMWR 55-1650-399, Dated 7 June 2013 TN 125666A 1/7/2014

MEC D176941 12/20/13

DOCUMENT CHANGE IS REQUIRED Verification: Hands-On Table-Top None

Revision A: MEC D176941, corrected 2-D data matrix size Note 11 found on DMWR pages 1-12, 1-13 and 1-14 and update IUID query requirements.

CASTILLO.NOEL

.SR.1089736990

Digitally signed by

CASTILLO.NOEL.SR.1089736990

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=CASTILLO.NOEL.SR.1089736990 Date: 2014.02.13 13:10:05 -06'00'

NOLEN.OTIS.

F.1231157146

Digitally signed by

NOLEN.OTIS.F.1231157146

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=CONTRACTOR, cn=NOLEN.OTIS.F.1231157146 Date: 2014.02.13 12:12:23 -06'00'

Otis Nolen (Camber Corporation)

PETER.ROBERT.

ARTHUR.JR.108

7823942

Digitally signed by

PETER.ROBERT.ARTHUR.JR.1087823942

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=PETER.ROBERT.ARTHUR.JR.108782394 Date: 2014.02.17 15:39:15 -06'00'

Noel Castillo Robert Peter PUBLICATION CHANGE REQUEST: REQUEST THAT THE FOLLOWING DATA BE INCLUDED IN THE NEXT

CHANGE OR REVISION TO THE PUBLICATION IDENTIFIED ABOVE.

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

1-4 1-6.c.(3) CHANGE paragraph to read: "If during PSA, it is determined that the serial number of the PTU, Hydraulic Motor or Hydraulic Pump is not appended with an inspection/procedure/configuration code, but a code is required during the M&O process, the code shall only be displayed on the IUID data plate as HRI in the MII field (e.g. MII: A). If multiple inspection/procedure/configuration codes are required, the codes shall be added to the MII field (not the serial number) as HRI, with each code separated by a dash (e.g. MII: A-XX-XX-X). Historical records shall be updated to document the change. When using DA Form 2410 electronic-system, the applicable code(s) shall be entered in the "MII" field; using the paper system the code(s) shall be entered in the "REMARKS" field (e.g., "MII: A" or "MII: A-X-XX-XX-X" for multiple codes)."

Formatted Cont. Sheet

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-6

1-7

1-6.d.1

1-6.d.(1) (a)

1-6.d.(1) (b)

1-6.d.(2)

1-6.d.(2)

1-6.d.(3)

1-6.d.(3)

1-6.d.(4)

CHANGE Figure to read: "Figure 1-2, Sheet 4 of 5".

CHANGE paragraph to read: "A Construct 1 UII shall be encoded into an ECC 200 compliant 2-D data matrix. The CAGE and Unique Component Number (UCN) shall be acquired from AMCOM’s The Army Maintenance Management System – Aviation (TAMMS-A)/Unique Item Identification (UID) database at https://tamms-a.redstone.army.mil (Appendix A). The Text Element Identifiers (TEIs) SPL and UCN shall be used as the data qualifiers. The component’s manufacturer serial number as found at PSA (minus any maintenance inspection codes) shall not be used to develop the UII, but shall reside as HRI on the component IUID data plate (Reference Figure 1-2, Sheet 4 of 5 for SPL and UCN configuration)."

CHANGE in last sentence "maintenance/repair/overhaul" to read: "M&O event".

CHANGE "Figure 1-2, Sheet 2 of 5 to" read: "Figure 1-2, Sheet 4 of 5".

CHANGE to read: "The recorded UII (see paragraph 3-6.1) shall be encoded into an ECC 200 compliant 2-D data matrix. M&O of the component shall not change the UII. The component’s manufacturer serial number (minus any maintenance inspection codes) as found at PSA shall reside as HRI on the component IUID data plate."

CHANGE in last sentence "M/R/O" to read: "M&O event".

CHANGE to read: "The recorded UII (see paragraph 3-6.1) shall be encoded into an ECC 200 compliant 2-D data matrix. M&O of the component shall not change the UII. The component’s manufacturer serial number (minus any maintenance inspection codes) as found by PSA shall reside as HRI on the component."

CHANGE last sentence to read: "If the 2-D data matrices do not meet the minimum grade requirements, a replacement IUID data plate shall be fabricated (see paragraph 1-6.d)."

D 1093 Rev A

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-8

1-11

1-12

1-13

1-14

3-5

Warning

NOTE 2

NOTE 4,

9, 10 and

10 and 11

10 and 11

3-6.1

1-2

CHANGE WARNING after paragraph 6 to read:

"WARNING

Isopropyl alcohol is flammable and toxic to eyes, skin, and respiratory tract.

Wear protective gloves and goggles/face shield. Avoid repeated or prolonged contact. Use only in well ventilated areas (or use approved respirator as determined by local safety/industrial hygiene personnel). Keep away from open flames, sparks, or other sources of ignition."

CHANGE "A, B OR C." to read: "B or C."

CHANGE in Note 4 "1100-H14" to read: "1100-H14 PER ASTM B 209" CHANGE Note 9 to read: "2-D DATA MATRIX TO CONTAIN THE MFR XXXXX

(MANUFACTURER’S CAGE CODE) AND SER XXXXXXX (MANUFACTURER’S

SERIAL NUMBER)."

CHANGE Note 10 to read: "2-D DATA MATRIX TO CONTAIN BOEING's

CURRENT PART NUMBER (PNR) AFTER AN M&O EVENT."

CHANGE Note 11 to read: "THE RECOMMENDED PART MARK SIZE FOR

THE 2-D MATIRX SYMBOL IS 0.25 - INCH TO 0.50 - INCH SQUARE. THE 2-D

DATA MATRIX SYMBOL SHALL NOT BE LARGER THAN 1.00 - INCH

SQUARE."

CHANGE in Note 4 "1100-H14" to read: "1100-H14 PER ASTM B 209" CHANGE Note 10 to read: "2-D DATA MATRIX TO CONTAIN BOEING's

CURRENT PART NUMBER (PNR) AFTER AN M&O EVENT."

CHANGE Note 11 to read: "THE RECOMMENDED PART MARK SIZE FOR

THE 2-D MATIRX SYMBOL IS 0.25 - INCH TO 0.50 - INCH SQUARE. THE 2-D

DATA MATRIX SYMBOL SHALL NOT BE LARGER THAN 1.00 - INCH

SQUARE."

CHANGE in Note 4 "1100-H14" to read: "1100-H14 PER ASTM B 209" CHANGE Note 10 to read: "2-D DATA MATRIX ENCODED WITH BOEING’S

CURRENT PART NUMBER USING DI (30P) AFTER AN M&O EVENT."

CHANGE Note 11 to read: "THE RECOMMENDED PART MARK SIZE FOR

THE 2-D MATIRX SYMBOL IS 0.25 - INCH TO 0.50 - INCH SQUARE. THE 2-D

DATA MATRIX SYMBOL SHALL NOT BE LARGER THAN 1.00 - INCH

SQUARE."

CHANGE paragraph 3-6.1, headings and sub-paragraphs, to read as follows:

"DETERMINE EXISTENCE OF UNIQUE ITEM IDENTIFIER (UII). The DoD IUID Registry and/or TAMMS-A/UID database shall be queried to determine if the component has been assigned a UII.

D 1093 Rev A

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

a. If 2-D data matrices are present, use a handheld data matrix reader (see Table 2-1) to scan the 2-D data matrices. If the scan is successful, proceed to paragraph 1-6.1.d and/or 1-6.1.e. If the scan is not successful after two attempts, proceed to paragraph 1-6.1.b.

b. Clean the 2-D data matrices with a cloth (Item 2, Appendix C) moistened with isopropyl alcohol (Item 16, Appendix C) and scan again. If the third scan is successful, proceed to paragraph 3-6.1.d.(1) and/or 3-6.1.e.(1). If the third scan is not successful, use the HRI to query the DoD IUID Registry (see paragraph d.(2)) and/or TAMMS-A/UID database (see paragraph 3-6.1.e.(2)).

c. If neither OPM IUID Label(s) nor IUID data plate(s) are present (only an original nameplate), query the DoD IUID Registry IAW paragraph 3-6.1.d.(2) and/or TAMMS-A/UID database paragraph 3-6.1.e.(2) below.

d. Query the DoD IUID Registry (see Appendix A, Websites) as follows:

(1) DoD IUID Registry home page, select “Queries”, then “Single Item Query.”

Scan or place the recorded UII data into the “UII*” field. If the query returns a record, proceed to paragraph 3-6.1.f. If the query does not return a record proceed to 3-6.1.d.(2) below.

(2) Using the human readable manufacturer serial number on the component (indicated by Serial No., Ser No., S/N, SN, SER, (S), SEQ, etc.), query the DoD IUID Registry. Select “Queries,” then “Pedigree Query.” Place the human readable manufacturer serial number in the “Serial Number” field. The query may return multiple records. Use the additional data from the component (component description, part number, etc.) to determine if one of the registry records can be matched to the component. If a registry record’s data matches the component data exactly, proceed to paragraph 3-6.1.f. If no registry record can be matched exactly to the component data, proceed to paragraph 3-6.1.d.(3) below.

(3) Using the human readable manufacturer serial number on the component (indicated by Serial No., Ser No., S/N, SN, SER, (S), SEQ, etc.), query the DoD IUID Registry. Select “Queries,” then “Mark Query.” Place “SERIAL NUMBER” in the “Mark Content” field and place the human readable manufacturer serial number (as visible on component, minus any spaces) in the “Mark Value” field.

The query may return multiple records. Use the additional data from the component (component description, part number, etc.) to determine if one of the registry records can be matched to the component. If a registry record’s data matches the component data exactly, proceed to paragraph 3-6.1.f. If no registry record can be matched exactly to the component data, (i.e., did not have a registered UII), an IUID data plate(s) shall be fabricated IAW paragraph 1-6.d.

D 1093 Rev A

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

A-2

A-3

e. Query the TAMMS-A/UID database (see Appendix A, Websites) as follows:

(1) TAMMS-A home page, select ”Apps”, then “UID” from the drop down menu.

Scan or place the recorded UII data into the “UII” field. If the query returns a record, proceed to paragraph 3-6.1.f. If the query does not return a record proceed to 3-6.1.e.(2) below.

(2) Using the human readable manufacturer serial number on the component (indicated by Serial No., Ser No., S/N, SN, SER, (S), SEQ, etc.) query the TAMMS-A/UID database by placing the serial number in the “SER” field. The query may return multiple records. Use the additional data from the component (component description, part number, etc.) to determine if one of the database records can be matched to the component. If a database record matches the component data exactly, proceed to paragraph 3-6.1.f. If no database record can be matched exactly to the component data, (i.e., did not have a registered UII), an IUID data plate(s) shall be fabricated IAW paragraph 1-6.d.

f. Record Data.

(1) Ensure the data in the DoD IUID Registry and/or TAMMS-A/UID database record matches the component data (resident on the PTU, Hydraulic Motor, Hydraulic Pump or within its accompanying historical records). If all data matches, record all pertinent component data (UII Data Elements, Boeing PN, Manufacturer PN (if applicable), and all other data on the component and/or in the registry record), as needed for IUID data plate replacement. If applicable, remove the OPM IUID Label(s). (Note: The label(s) may be retained with the component as reference only). It is necessary that all recorded data be matched to the same end item, assembly, or component on which they were found during PSA. Refer to paragraph 1-6.d for IUID data plate fabrication.

(2) If the data in the DoD IUID Registry and/or TAMMS-A/UID database record does not match the component data, refer to paragraph 1-6.d for IUID data plate fabrication. If applicable, remove the OPM IUID Label(s). (Note: The label(s) may be retained with the component as reference only)."

CHANGE MCDS web address to read:

"TAMMS-A/MCDS: The Army Maintenance Management System – Aviation/Maintenance Consolidated Database System https://tamms-a.redstone.army.mil"

D 1093 Rev A

RDMR-AEM

MEMORANDUM FOR RECORD:

SUBJECT: Impact of AED Maintenance Engineering Order (MEO) on maintenance using ,affecting system:

Enclosed MEO is issued by this office and is provided as part of our Technical Data user support mission.

4. THIS MEO CHANGES THE FOLLOWING (Check all that apply):

1.

Consumables

Materials

Expendables

Repairable Bill of Materials (RBOM)Impact

3. PRIORITY IMPLEMENTATION CATEGORY :

6. Comments:

7. Point of contact for this action is

2. FOR AMCOM ACQUISITION CENTER USE ONLY:

This MEO was written as a request from a contractor/KO on an active M&O contract.

Request that MEO be transmitted to the contractor as soon as possible.

b.Items checked in this area are considered Normal Priority Implementation Category.

Illustrated Parts Breakdown Change Mandatory Replacement Part

TSO/TSN Change Configuration Change

Publication New Change

Hardware Tooling Equipment

New/Revised Procedure/Process

Process Improvement Project Inspection

Special Process Testing Cost Savings a.Items checked in this area are considered High Priority Implementation Category.

5. Reason(s) MEO Written:

Other

Other

D 1093 Rev A

DMWR 55-1650-399, Dated 7 June 2013 CH47

D 1093 Rev A

4) Normal - Can be implemented with normal priority

Parts Marking Implementation/Update

Revision A: MEC D176941, corrected 2-D data matrix size Note 11 found on DMWR pages 1-12, 1-13 and 1-14 and update IUID query requirements.

Noel Castillo MED Engineer, 361-961-1741,Otis Nolen (Camber Corporation), 36-961-2980

CASTILLO.NOEL.SR.10897

36990

Digitally signed by CASTILLO.NOEL.SR.1089736990 DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=CASTILLO.NOEL.SR.1089736990 Date: 2014.02.13 13:11:09 -06'00'

Noel Castillo