W52P1J15R0033-0002.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. Contract ID Code Page Of

2. Amendment/Modification No.

3. Effective Date

4. Requisition/Purchase Req No.

5. Project No. (If applicable)

6. Issued By Code 7. Administered By (If other than Item 6) Code

8. Name And Address Of Contractor (No., Street, City, County, State and Zip Code)

9A. Amendment Of Solicitation No.

9B. Dated (See Item 11)

10A. Modification Of Contract/Order No.

10B. Dated (See Item 13) Code Facility Code

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

The above numbered solicitation is amended as set forth in item 14. The hour and date specified for receipt of Offers is extended, is not extended.

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing items 8 and 15, and returning ____________ copies of the amendments: (b) By acknowledging receipt of this amendment on each copy of the offer submitted; or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. Accounting And Appropriation Data (If required)

13. THIS ITEM ONLY APPLIES TO MODIFICATIONS OF CONTRACTS/ORDERS

It Modifies The Contract/Order No. As Described In Item 14.

A. This Change Order is Issued Pursuant To: The Changes Set Forth In Item 14 Are Made In

The Contract/Order No. In Item 10A.

B. The Above Numbered Contract/Order Is Modified To Reflect The Administrative Changes (such as changes in paying office, appropriation data, etc.) Set

Forth In Item 14, Pursuant To The Authority of FAR 43.103(b).

C. This Supplemental Agreement Is Entered Into Pursuant To Authority Of:

D. Other (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return _______________ copies to the Issuing Office.

14. Description Of Amendment/Modification (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

Except as provided herein, all terms and conditions of the document referenced in item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. Name And Title Of Signer (Type or print)

16A. Name And Title Of Contracting Officer (Type or print)

15B. Contractor/Offeror 15C. Date Signed 16B. United States Of America 16C. Date Signed

By (Signature of person authorized to sign) (Signature of Contracting Officer)

NSN 7540-01-152-8070

PREVIOUS EDITIONS UNUSABLE

30-105-02 STANDARD FORM 30 (REV. 10-83)

Prescribed by GSA FAR (48 CFR) 53.243

SEE SCHEDULE

X

Firm Fixed Price

0002 2016MAY19

W52P1J

ARMY CONTRACTING COMMAND - RI

ROCK ISLAND, IL 61299-8000

BLDGS 60 & 62

BRIDGET L. KRAMER

EMAIL: BRIDGET.L.KRAMER.CIV@MAIL.MIL

W52P1J-15-R-0033

2016MAY09

X

X

/SIGNED/

2 signed

SEE SECOND PAGE FOR DESCRIPTION

1 10

CONTINUATION SHEET

Reference No. of Document Being Continued Page of

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION A - SUPPLEMENTAL INFORMATION

Buyer Name: BRIDGET L. KRAMER

Buyer Office Symbol/Telephone Number: CCRC-AC/(309)782-0896

Type of Contract 1: Firm Fixed Price

Kind of Contract: Supply Contracts and Priced Orders

*** End of Narrative A0000 ***

The purpose of this Amendment 0002 to solicitation W52P1J-15-R-0033 is to answer the following questions that have been received:

Question 1 - Page 23, CLIN 0006, M821A3: Please confirm that packaging drawing and date are correct.

Answer 1 - Page 23, CLIN 0006, M821A3 is incorrect as written. The correct drawing is 13038139, Revision A, dated 30 Mar 15. Under clause 52.211-4508, on page 23, CLIN 0006, M821A3 has been added to the paragraph pertaining to CLIN 0006, M889A4.

Question 2 - Page 24, CLIN 0006, M821A3: Please confirm that Unitization reference and document date are correct.

Answer 2 Page 24, CLIN 0006, M821A3 is incorrect as written. The correct Unitization reference is 19-48-4116/43N, Revision 3, dated

September 2002. Under clause 52.247-4517, on page 24, CLIN 0006, M821A3 has been added to the paragraph pertaining to CLIN 0006, M889A3 and M889A4.

Question 3 - For technical oral presentation, in a case where the prime contractor has the capability to LAP both CLIN Groups 1 and 2 and having some slides being the same for both CLIN Groups, could the presenters for the first CLIN Group present all details and for the second CLIN Group explain the applicable changes?

Answer 3 - No, each CLIN Group is being evaluated separately. Therefore, all information pertaining to each CLIN Group shall be included in the presentation and presented separately; Even if this means duplicating information. If it is not in the presentation, it will not be used for evaluation.

4. Clause 52.210-4501, Drawings/Specifications has been updated to reflect the most recent TDP certification dates.

5. The closing date for solicitation W52P1J-15-R-0033 remains unchanged.

6. All other terms and conditions remain unchanged.

*** END OF NARRATIVE A0003 ***

2 10

W52P1J-15-R-0033 0002

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION C - DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

Status Regulatory Cite Title Date Status Regulatory Cite Title Date _______ _______________ ______________________________________________________________________ ____________ _______ _______________ ______________________________________________________________________ ____________

C-1 CHANGED 52.210-4501 DRAWINGS/SPECIFICATIONS APR/2012

(ACC-RI)

CLIN 0001, applies to M768:___________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

Technical Data Package Listing TDPL 13031777, with revision A in effect as of 06/09/2015 except for those included in M768

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0001, applies to M720A1:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

Technical Data Package Listing TDPL 13044446, with revision B in effect as of 06/09/2015 except for those included in M720A1

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0002, applies to M720A2:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

Technical Data Package Listing TDPL 13028739, with revision B in effect as of 07/08/2015 except for those included in M720A2

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0002, applies to M768A1:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

Technical Data Package Listing TDPL 13028737, with revisions in effect as of 06/15/2015 except for those included in M768A1

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0005, applies to M889A1:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

3 10

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Technical Data Package Listing TDPL 12953279, with revisions in effect as of 06/04/2015 except for those included in M889A1

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0005, applies to M889A2:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

Technical Data Package Listing TDPL 13013654, with revisions in effect as of 06/24/2015 except for those included in M889A2

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0005, applies to M821A2:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

Technical Data Package Listing TDPL 12977144, with revisions in effect as of 06/17/2015 except for those included in M821A2

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0006, applies to M889A3:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

Technical Data Package Listing TDPL 13038141, with revision B in effect as of 06/04/2015 except for those included in M889A3

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0006, applies to M889A4:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

Technical Data Package Listing TDPL 13038142, with revisions in effect as of 06/24/2015 except for those included in M889A4

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

CLIN 0006, applies to M821A3:_____________________________

(a) In addition to the drawing(s) and/or specifications listed below, other documents which are part of this procurement and which apply to Preservation/Packaging/Packing and Inspection and Acceptance are contained elsewhere.

(b) The drawing(s) and specifications are applicable to this procurement. Drawings and Specifications in accordance with

4 10

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Technical Data Package Listing TDPL 13038140, with revisions in effect as of 06/25/2015 except for those included in M821A3

Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033.

(c) Technical Data Packages, including any exceptions thereto, will be obtained electronically in accordance with the clause titled "Technical Data Package Information and Distribution and Destruction of Restricted Technical Data" in Section C of this document.

(End of statement of work)

(CS6100)

5 10

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION D - PACKAGING AND MARKING

Status Regulatory Cite Title Date Status Regulatory Cite Title Date _______ _______________ ______________________________________________________________________ ____________ _______ _______________ ______________________________________________________________________ ____________

D-1 CHANGED 52.211-4508 PACKAGING REQUIREMENTS JUL/1997

(ACC-RI)

CLIN 0001, applies to M768 and M720A1:______________________________________

(a) Packaging shall be in accordance with 12993657 revision F, dated 19 Oct 2012.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 12993657, Rev F, dated 19 OCT 2012. 2-D Bar Code markings are required in accordance with Drawing 12999545, Rev H, and dated 2 APR 2015.

EXCEPTION: Engineering Exceptions found on Section C Exceptions located at https://www.fbo.gov/fedteds/W52P1J15R0033

Performance Oriented Packaging: Prior to shipment, the manufacturer shall make sure the container has been tested by a government approved Performance Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation. Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the government. The POP test report shall be generated by the Manufacturer/Laboratory following the test. The report must be kept on file by the contractor and submitted as required by the Contract Data Requirement List. (DI-PACK-81059) For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: (a) the initial POP test report expires before the end of the contract or (b) there is a change in container manufacturer or design of the exteriors shipping container. No re-test is needed if all packaging is purchased while under an expired POP test. DI-PACK-81059 is required for this contract.

EXCEPTION TO POP MARKINGS: If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent

Authority of the country of manufacture.

PERFORMANCE ORIENTED PACKAGING (POP) VERIFICATION: In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight. If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

HEAT TREAT WOOD QUALITY MARKING: In accordance with the requirements of International Standards for Phytosanitary Measures

(ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood Packaging Material (WPM). WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frames, and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board. All WPM shall be constructed from Heat Treated (HT to 56 degrees Centigrade for 30 minutes) lumber and certified by an accredited agency recognized by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material

Enforcement Regulations (see URL: http://www.alsc.org). All materials must include certification markings in accordance with

ALSC standards and be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides and ends of the pallet and be contrasting and clearly visible.

All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ALSC approved

DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry.

CLIN 0002, applies to M720A2:_____________________________

(a) Packaging shall be in accordance with 13027661 revision H, dated 02 Jul 2015.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 13027661, Revision H, Dated 02 JUL 15. 2-D Barcodes are required in accordance with

12999545, Revision H, Dated 02 APR 15.

EXCEPTION: The following shall apply to drawing 13027661, revision H, dated 02 JUL 15:

PERFORMANCE ORIENTED PACKAGING: Prior to shipment, the manufacturer shall make sure the container has been tested by a government approved Performance Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance

6 10

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

with Title 49 Code of Federal Regulation. Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the government. The POP test report shall be generated by the Manufacturer/Laboratory following the test. The report must be kept on file by the contractor and submitted as required by the Contract Data Requirement List. (DI-PACK-81059) For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: (a) the initial POP test report expires before the end of the contract or (b) there is a change in container manufacturer or design of the exteriors shipping container. No re-test is needed if all packaging is purchased while under an expired POP test. DI-PACK-81059 is required for this contract.

EXCEPTION TO POP MARKINGS: If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The Contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent

Authority of the country of manufacture.

PERFORMANCE ORIENTED PACKAGING (POP) VERIFICATION: In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight. If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

CLIN 0002, applies to M768A1:_____________________________

(a) Packaging shall be in accordance with 13027661 revision G, dated 27 Aug 2014.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 13027661, Revision G, dated 27 Aug 2014. 2-D Barcodes are required in accordance with

12999545, Rev H, dated 02 April 2015.

EXCEPTION: The following shall apply to drawing 13027661, revision G, dated 27 Aug 2014:

Performance Oriented Packaging: DI-PACK-81059 is required for this contract.

PERFORMANCE ORIENTED PACKAGING: Prior to shipment, the manufacturer shall make sure the container has been tested by a government approved Performance Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation. Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the Government. The POP test report shall be generated by the Manufacturer/Laboratory following the test. The report must be kept on file by the contractor and submitted as required by the Contract

Data Requirement List. (DI-PACK-81059) For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: (a) the initial POP test report expires before the end of the contract or (b) there is a change in container manufacturer or design of the exteriors shipping container. No re-test is needed if all packaging is purchased while under an expired POP test.

EXCEPTION TO POP MARKINGS: If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable).

The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent Authority of the country of manufacture.

PERFORMANCE ORIENTED PACKAGING (POP) VERIFICATION: In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight. If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

HEAT TREAT WOOD QUALITY MARKING: "In accordance with the requirements of the International Standards for Phytosanitary Measures

(ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging

Material Policy and Wood Packaging Material Enforcement Regulations (see URL: http://www.alsc.org). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment

Marking. Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible.

All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite surfaces. Foreign manufacturers shall have the heat treatment and marking of nonmanufactured wood products verified in accordance with the ISPM-15 compliance program.

7 10

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

CLIN 0005, applies to M889A1, M889A2 and M821A2:________________________________________________

(a) Packaging shall be in accordance with 12993638 revision K, dated 04 Mar 2014.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 12993638, Revision K, Dated 04 MAR 14. 2-D Barcodes are required in accordance with

12999545, Revision H, Dated 02 APR 15.

EXCEPTION: The following shall apply to drawing 12993638, revision K, dated 04 MAR 14:

PERFORMANCE ORIENTED PACKAGING: Prior to shipment, the manufacturer shall make sure the container has been tested by a government approved Performance Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation. Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the government. The POP test report shall be generated by the Manufacturer/Laboratory following the test. The report must be kept on file by the contractor and submitted as required by the Contract Data Requirement List. (DI-PACK-81059) For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: (a) the initial POP test report expires before the end of the contract or (b) there is a change in container manufacturer or design of the exteriors shipping container. No re-test is needed if all packaging is purchased while under an expired POP test. DI-PACK-81059 is required for this contract.

EXCEPTION TO POP MARKINGS: If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The Contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent

Authority of the country of manufacture.

PERFORMANCE ORIENTED PACKAGING (POP) VERIFICATION: In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight. If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

CLIN 0006, applies to M889A3:_____________________________

(a) Packaging shall be in accordance with 13038139 revision B, dated 11 Aug 2015.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 13038139, Revision B, dated 11 AUG 2015. 2-D Barcodes are required in accordance with

12999545, Rev H, dated 02 APRIL 2015.

EXCEPTION: The following shall apply to drawing 13038139, Revision B, dated 11 AUG 2015:

PERFORMANCE ORIENTED PACKAGING: Prior to shipment, the manufacturer shall make sure the container has been tested by a government approved Performance Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation. Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the government. The POP test report shall be generated by the Manufacturer/Laboratory following the test. The report must be kept on file by the contractor and submitted as required by the Contract Data Requirement List. (DI-PACK-81059) For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: (a) the initial POP test report expires before the end of the contract or (b) there is a change in container manufacturer or design of the exteriors shipping container. No re-test is needed if all packaging is purchased while under an expired POP test. DI-PACK-81059 is required for this contract

EXCEPTION TO POP MARKINGS: If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent

Authority of the country of manufacture.

PERFORMANCE ORIENTED PACKAGING (POP) VERIFICATION: In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight. If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

HEAT TREAT WOOD QUALITY MARKING: "In accordance with the requirements of the International Standards for Phytosanitary Measures

(ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC)

8 10

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

and is required for all Wood Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of nonmanufactured wood shall be heat-treated. All WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging

Material Policy and Wood Packaging Material Enforcement

Regulations (see URL: http://www.alsc.org). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment Marking. Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention

Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible. All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite surfaces. Foreign manufacturers shall have the heat treatment and marking of non-manufactured wood products verified in accordance with the ISPM-15 compliance program.

CLIN 0006, applies to M889A4 and M821A3:________________________________________

(a) Packaging shall be in accordance with 13038139 revision A, dated 30 Mar 2015.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 13038139, Revision A, Dated 30 MAR 15. 2-D Barcodes are required in accordance with

12999545, Revision H, Dated 02 APR 15.

EXCEPTION: The following shall apply to drawing 13038139, revision A, dated 30 MAR 15:

PERFORMANCE ORIENTED PACKAGING: Prior to shipment, the manufacturer shall make sure the container has been tested by a government approved Performance Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation. Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the government. The POP test report shall be generated by the Manufacturer/Laboratory following the test. The report must be kept on file by the contractor and submitted as required by the Contract Data Requirement List. (DI-PACK-81059) For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: (a) the initial POP test report expires before the end of the contract or (b) there is a change in container manufacturer or design of the exteriors shipping container. No re-test is needed if all packaging is purchased while under an expired POP test. DI-PACK-81059 is required for this contract.

EXCEPTION TO POP MARKINGS: If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The Contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent

Authority of the country of manufacture.

PERFORMANCE ORIENTED PACKAGING (POP) VERIFICATION: In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight. If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

(End of clause)

(DS6303)

D-2 CHANGED 52.247-4517 PALLETIZATION INSTRUCTION MAR/1992

(ACC-RI)

CLIN 0001, applies to M768 and M720A1:______________________________________

Palletization shall be in accordance with 19-48-4116/28T, revision 2, dated June 2008 and 1948-4116, Rev 12, DATED DEC 11.

Marking shall be in accordance with ACV00561, revision F, dated 2 Dec 2008. Wood Packaging Material (WPM) shall be in accordance with ACV00831, dated 01 Mar 2010. 2-D Bar Code marking is required.

CLIN 0002, applies to M720A2 and M768A1:________________________________________

9 10

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Palletization shall be in accordance with 19-48-4116/28U, revision 1, dated May 2015 and 19-48-4116, Revision 12, dated DEC

2011, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with

ACV00561, Revision F, dated 02 DEC 2008. WPM shall be in accordance with ACV00831, dated 01 MAR 2010. 2-D barcodes are required.

CLIN 0005, applies to M889A1, M889A2 and M821A2:________________________________________________

Palletization shall be in accordance with 19-48-4116/43N, revision 3, dated September 2002 and 19-48-4116, Revision 12, dated

DEC 2011, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with ACV00561, Revision F, dated 02 DEC 2008. WPM shall be in accordance with ACV00831, dated 01 MAR 2010. 2-D barcodes are required.

CLIN 0006, applies to M889A3, M889A4 and M821A3:________________________________________________

Palletization shall be in accordance with 19-48-4116/43N, revision 3, dated September 2002 and 19-48-4116, Revision 12, dated

DEC 2011, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with ACV00561, Revision F, dated 02 DEC 2008. Wood Packaging Material (WPM) shall be in accordance with ACV00831, Dated: 01 MAR

2010. 2-D barcodes are required.

(End of clause)

(DS6204)

10 10