Exhibit 004 - CDRL A004 - Supplementary QAP - M82 353dRevA.pdf
PDF 129 KB Posted
- Attached to
- Propellant Retainer Assembly
- Solicitation number
- W519TC-24-R-2027
About this file
This document is a Supplementary Quality Assurance Provisions (SQAP) for a Propellant Retainer Assembly (drawing 13-19-153, specification EA-G-1723) for the Pine Bluff Arsenal. The SQAP outlines detailed inspection and testing requirements for the assembly, including two critical test methods: a Leakage Test and an Inner and Outer Clip Position Test. The Leakage Test requires applying 5 psi of air to the clip side and checking for any leaks using a liquid detector solution, with no leakage permitted. The Clip Position Test specifies precise positional tolerances for the inner clip (diameter .138") and outer clip (diameter .178"), with specific positioning requirements relative to Datum-B.
The document follows MIL-STD-1916 for quality assurance and is prepared by Kenny Daniel and Kevin Atnip from the DIR - Product Assurance at Pine Bluff Arsenal. The SQAP mandates 100% examination for critical characteristics and emphasizes that the supplier is responsible for performing all inspection requirements, with the government reserving the right to conduct additional inspections to ensure the supplies conform to specified requirements. The sample rate for testing is specified as VL-III per MIL-STD-1916, and the Contracting Officer may approve alternate test methods.
View the file
Other files
Show all 15
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Propellant Retainer Assembly drawing 13-19-153 specification EA-G-1723
Critical
Major
SUPPLEMENTARY QUALITY ASSURANCE PROVISIONS (SQAP)
RESPONSIBILITY FOR INSPECTION - Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified, herein. Except as otherwise specified in the contract or order, the supplier may use his or any other facilities, unless disapproved by the government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to specified requirements. Suppliers contract to meet all
PART I - LIST OF APPLICABLE DOCUMENTS/STANDARDS
NUMBER
MIL-STD-1916
TITLE
DOD TEST METHOD STANDARD - DOD PREFERRED METHODS FOR ACCEPTANCE OF PRODUCT
TITLESupplementary Quality Assurance
Provisions for:
Number/Specification
PART II - EXAMINATION OF PROVISIONS
CLASSIFICATION OF QUALITY CONFORMANCE CHARACTERISTICS
100% Examination shall be performed for critical characteristics. Examination of major and minor characteristics shall be performed in accordance with the classification of quality conformance charactistics contained herein utilizing the
CLASSIFICATION OF DEFECTS
VERIFICATION
LEVEL
INSPECTION
METHOD
CATEGORIES DEFECTS
Codes *CD* contractor Designed Equipment *CE* Commercial Inspection Equipment *VI* Visual Inspection
M82 353d DATE: June 27-2023 SHEET:1 of SQAP:
Kenny Daniel / Kevin Atnip DIR - PRODUCT ASSURANCE - PINE BLUFF ARSENALPREPARED BY:
PBA FORM 702-103 1 November 1999
Minor test for each listed characteristic per spec
EA-G-1723C
kenneth.g.daniel Cross-Out
Propellant Retainer Assembly (13-19-153)
Test Method A: Leakage Test
Using a suitable adapter, apply 5 psi (+2,-0 psi) of air on the clip side of the assembly. Wet the powder well/ match side 90.950" dia.) with liquid leak detector solution (or equal soap solution). Maintain the pressure a minimum of two minutes and observe for evidence of leakage. No leakage is allowed. Any foam or bubbles in the powder well shall be evidence of leakage. CAUTION: The base assembly must be securely restrained and the test pressure should not exceed 10 psig. The sample rate shall be VL-III per MIL-STD-1916.
The Contracting Officer may approve an alternate test method.
Test Method B: Inner and Outer Clip Position
Determine the Position of the Inner clip (13-19-115) diameter .138" and Outer clip (13-19-114) diameter .178".
Use basic dimension locators and datums (dwg 13-19-164) for view C-C diameter .091".
Inner Clip (small clip) Diameter .138" position with a .025" positional tolerance range at maximum material condition (MMC) to Datum -B-.
Outer Clip (large clip) Diameter .178" position with a .010" positional tolerance range at maximum material condition (MMC) to Datum -B-.
NOTE: Positional dimensions apply after assembly of clips.
Kenny Daniel / Kevin Atnip
VERIFICATION
LEVEL
INSPECTION
LEVEL
CATEGORIES DEFECTS
DATE: June27-2023 SHEET: 2 of
DIR - PRODUCT ASSURANCE - PINE BLUFF ARSENAL
SQAP: M82 353d
PREPARED BY:
PBA FORM 702-103 1 November 1999
File details come from the government source that posted it. Updated .