Surfacing_Specifications-Turf-ShawGrass.pdf

INSTALLATION

GUIDELINES

When installed properly, Shawgrass turf will deliver durability and performance for many years. Preparation of the site is critical for long term success and will yield the best results. Follow these guidelines to ensure that your projects are planned efficiently, and your customers get the results they need.

A M

ERICAN OWNED

& O P E R ATE D

A M

ERICAN OWNED

& O P E R ATE D

PLANNING1

Area The area for turf installation should be clearly defined and marked.

Soil Condition Check to see if you will need to wet or soften the ground or use a jackhammer to remove large rocks. Rain soaked soil may need to dry a few days before synthetic turf work begins.

Irrigation Locate existing sprinklers or bubblers for the remaining trees and plants or complete irrigation for trees and plants first. Identify all irrigation lines, electrical conduit, etc. below ground that could be damaged during the synthetic turf installation. Reroute where possible.

Irrigation sprinklers are not needed for lawn turf, you will want to consult your Irrigation specialist to assist in rerouting or shutting off heads. If you opt for the HydroChill cooling technology you may want to simply change the irrigation settings at the box as your customer will benefit from having an easy watering source.

Preventing Future Damage Determine if additional supplies are needed to prevent damage from rodents or ground animals. Rodent wire (similar to chicken wire) may be appropriate. Secure the entire perimeter to prevent the synthetic turf from being pulled up or damaged by pests.

Existing Design Elements Locate existing concrete borders and determine whether you need to nail into concrete footings. If you are using curbing, edging or border materials, install it prior to cutting the synthetic turf and adding any base material, as this will give you a more accurate measurement for the synthetic turf. Tree roots and pest control should also be considered.

Measurements To reduce labor, measure the project area carefully and design the layout to minimize the number of seams in the synthetic lawn. Plan for a little extra material, especially if you involve curves in your design. A good figure to use is 10%. Use a smart level or transit for proper slope of 2% min.

Design Application Tips All synthetic turf products have a pile (grain) direction that must be taken into account. Note the pile direction and install all sections of synthetic turf in the same pile pattern. Installing synthetic turf in opposing pile patterns may result in noticeable seams. The grain should face toward the primary viewpoint as this will minimize sheen.

Drainage Determine whether the project area has an adequate existing drainage or will require additional drains or modified drains, grading or sloping.

Turf Measure the entire turf area, and order more than enough turf to cover the entire area. Do this even if you only do partial installations.

Turf is manufactured in individual batches with normal batch to batch variation, so you will want to order enough for your entire job.

Turf is typically manufactured in rolls that are 12 or 15 ft. wide, so you should break your installation area into 12 or 15 ft. wide sections, and then add the total length of these areas.

Roll out the turf the day before installation as this will allow the panel to relax. If the synthetic turf has wrinkles, lay it flat on a flat surface in the sun or stretch.

Taller pile heights will require more infill so be mindful of your calculations. Also, remember that turf wrapped closest to the core may be excessively wrinkled. Plan on about 18 in. of waste just to be on the safe side.

Base Material You will need approximately 2 - 6 in. of stone base under your turf. 1 yd. of base material will cover 80 sqft. at 4 in. depth (1 yd. = 1 tn.) Fine stone or aggregate (89 stone; ¼ – 5/8 in. in size) can be applied over a coarse aggregate (57 stone; 1/2 – 3/4 in.

in size), or a mix of coarse and fine aggregate (often referred to as crush and run) can be used. Your local building supply vendor will be your best source, and may offer delivery and installation options. Avoid using pea gravel as your base material. DO NOT use pea gravel as rounded stone will shift too much. Pea gravel stones have a smooth, round surface, which make them hard to compact. Your local nursery, mulch or stone center will be your best options for gravel.

Infill Infill helps weigh the turf down and stabilize the fibers to keep them upright and prevent matting. Infill is essential as it assists with drainage and creates a firm, natural feeling base. Specialized infills can be used as well. HydroChill cools surface temperatures significantly and requires at least 2 lbs.

per sqft. to be effective. Envirofill is an infill that is green in color, offers cooling properties and has Microban®. Combining the two provides excellent performance for children or pets.

Sand Infill In some geographic areas, you may want to use a color coated sand on the top of your infill. Coated sand is more expensive than white or natural sand, so it is normally only used on the top of your infill. A good rate would be 1 lb. per sqft. Calculate the amount of sand infill in advance; a good estimate is 3 - 5 lbs. of sand per sqft. on 50 - 80 oz. turf.

K9 Sand is a biogenic, safe, renewable, and sustainable alternative to standard infills.

It spreads easily and evenly into turf and contains no microplastics. K9 Sand is dust free, silica free, and quartz free. K9 Sand is a safe, effective, and nontoxic infill, perfect for your beloved pet.

K9 Sand can only be used on Flow-Through perforated turf.

MATERIAL

PREPARATION

Hydrochill HydroChill is an evaporative cooling technology used to cool synthetic turf surfaces. The HydroChill technology is a pre-coated material so it arrives on site already bonded to the sand infill. Once installed, just hydrate to activate. HydroChill requires moisture to provide the long-term cooling effect.

We highly recommend HydroChill as it is a specialized infill that drives surface temperatures down significantly. When used around families, pets and children it provides an extra level of comfort and provides the best peace of mind on hot days.

Fabrics Don’t forget to procure the weed barrier.

You may also need a wire mesh rodent barrier if you have had prior rodent problems (gophers, moles, etc).

Seaming Material Be sure to have enough seaming tape to run the full length of your seams, as well as adhesive. Take time to do your seams correctly as this will be one of the most noticeable features when complete. Also, please be sure to read all adhesives labels to ensure that they are used and stored correctly.

Plan your project to minimize or hide seams;

for example place seams in the back or out of the line of sight. Also, consider reworking your design to maintain 15 ft. widths. This will save a lot of labor and potentially visible seams as well.

Landscape Nails/Spikes (approximately 3.5 – 10 in. in length)

Spikes will be used alongside sidewalks, tree rings and other objects in the area to landscape. They will eventually be covered by infill but you will want to embed them as deeply as possible. There are a variety of spikes available ranging from plastic to galvanized/non-galvanized. Local soils will drive these considerations.

Application will determine size of nail or spikes to use. Nails should be applied approximately every six inches along the perimeter of the installation, as well as along all seams to secure turf.

Use nailer board nails one-to-two inches galvanized or staples ¼ – ½ in. Shorter nail spacing may be required when using nailer boards.

Edging Material Polyboard is superior to other lawn edging products because of its durability and multiple uses. It looks like real wood, but performs like plastic. Polyboard can be bent and curved to fit all your landscaping needs.

Pressure treated wood may also be used.

MATERIAL

PREPARATION

turf blade turf thatch

(optional) colored sand a Berkshire Hathaway Company 1-800-441-7429

Playground with Concrete and Playpad 5 054SG Playsafe 50 Turf System 139SG Playsafe 40 Turf System concrete curb nailer board (pressure treated or composite) concrete screw

1" - 2" galvanized nail

1"-2" depth 95% compaction sub-base geo textile

(crusher run)

(optional) turf chiller

95% compaction Playpad 5

2' - 5' critical fall 022616

F or reference purposes only if printed or dow nloaded.

a Berkshire Hathaway Company 1-800-441-7429

Playground with Ground Cover and Playpad 8 054SG Playsafe 50 Turf System 139SG Playsafe 40 Turf System turf blade turf thatch

(optional) turf chiller colored sand

(taper to height of thatch) screw for nailer board stake for nailer board (pressure treated or composite) nailer board (pressure treated or composite)

95% compaction

(crusher run)

Playpad 8

022616

95% compaction

F or reference purposes only if printed or dow nloaded.

• �Rubberized and leather gloves

• Back braces

• Knee guards

• Safety glasses

• First-aid kit

• �Safety cones — for use on street for materials and equipment

• �100 ft. flexible metal tape measure

• �Snap line for marking long cuts of turf

• �Hard-edge level — 2 - 4 ft.

• �Square or T-square for squaring edges of turf

• �Construction-grade wheel barrows

• �Flat head shovels

• �Spades — rounded head

• �Large picks

• �Small picks

• �Leaf rake

• Transit or smart level

• �Asphalt or landscape rake (40 in.)

• �Pointed mason trowels — used to clear and clean edges of concrete, etc.

• �Hand Tampers (8 in. or 10 in.)

• Water filled roller

• �2 in. x 1 in. x 2 ft. pieces of wood - for hand tamping edges and small areas

• �Commercial quality knives and blades (select a blade and knife set that is easily changeable and stock up on blades)

• �Drop spreaders for small jobs using a small drop spreader (holds approx. 75 lbs. of infill) or for larger areas, using a commercial drop spreader (holds approx. 200 lbs.) or walk-behind or tow behind units.

• �Installation and grooming rakes (poly-nylon)

• �Grooming hand brooms or tools (poly-nylon)

TOOLS &

EQUIPMENT

Safety Turf Cutting

Base Preparation

Measuring

Site Preparation Infilling

• �Several small and large tarps or plastic drop cloths

• �Several small containers for used blades and small buckets for hand-filling, small tools and job materials

• �Gas cans for both plain gas and mixes

• Water hose (100 ft.) and nozzle and variable heads

• Brooms (one soft bristle and one hard bristle)

• Small hand broom for rocks, edges, etc

• Shop vacuum (2 gal. to larger)

• �Fork lift with forks and 15 ft. carpet pole

• �Bungee cords or rope for securing loads

• Carpet dollies

Hand Tools

• �Power brush to fribulate (bloom) blades

• �Hand saw or power saw to cut bender board, pipes

• �Leaf blower (for cleanup of organic materials and job site areas)

• �Sod cutter (optional rental)

• �Vibratory plate compactor

(optional rental)

TOOLS &

EQUIPMENT

Power Tools Material Handling > 1000 SF

• �Small hand shovel — used to clear and clean around pipes and tight edges

• �Hammers

• �Pliers (various sizes and shapes)

• �Wrench and socket set — for small tool repairs and use in adjusting irrigation, etc

• �Sledge hammer (medium to large)

• Rubber mallets

• �Cement chisel for removing extra concrete, rocks or other obstructions

• �Pipe cutter (for medium modifications to irrigation)

Misc. Tools

Site Clean Up

A. Remove all turf, sod, mulch, etc. from the marked area. You can do this with a manual shovel, or a gas-powered sod puller (you can rent one at most rental centers) or have a local landscaper remove the existing sod and any landscaping you want removed from your installation area. Excavate 2 - 6 in. of turf and soil if removing an old lawn. You will later replace this turf and soil with 2 - 6 in. of stone base material.

B. If you are landscaping around trees, shrubbery, flowers, light poles, utilities, etc., remember to mark around these areas and account for the turf edge configuration.

C. Leave ample area uncovered around the bases of trees.

D. Check on local ordinances on disposal of green waste before starting. Let your site dry out for a few days before excavating.

E. Do not use a tiller to remove turf because that will disturb the soil below the sod and create a poor base. A sod cutter is recommended for large areas. These are available at many tool rental suppliers. A spade or shovel can be used to cut the sod into small strips in small areas.

F. Organic material left under the newly installed surfaces will decompose, which can lead to sub-surface failure. Any newly removed tree stump or root areas should be free of organic materials, then filled and compacted prior to job start.

G. Mark the boundaries of your lawn, and outline the layout using an inverted spray can marker.

Remember that synthetic turf comes in either 12 ft. or 15 ft. widths. Plan your installation with this in mind, to have as few seams as possible with your layout.

H. A variety of edging materials and border solutions may be used for your synthetic turf project. Examples may include: transitions from synthetic turf to a flower bed, mulch, stone edging or sidewalks. You may also use synthetic lumber or synthetic turf edging.

I. This is the perfect time to add edges, large rocks, install pavers, stepping stones, walkways and walls.

J. If you have a sprinkler system in the installation area, reroute to perimeter if possible, or cap the unnecessary sprinklers and turn off their valves.

AREA

PREPARATION2

Safety Call 811 before you dig to prevent damage to underground utilities and service interruption. This is the universal number for the 71 regional services that coordinate location services for underground public utilities in the U.S.

A. It may be necessary to compact the native soil/subgrade prior to base construction.

B. In the case where the native soils are soft and/or saturated, it is advisable to install a geotextile to separate the soft soils from the crushed stone base.

C. As a rule of thumb, if there is standing water, or if water comes to the surface under foot, a geotextile should be used.

D. You need to fully firm up the ground that will be the foundation for your turf. You can use a sod roller, or a vibrating plate compactor, which you can rent from your local rental suppliers. Ensure the existing ground is sloped properly or follows the grade of the surrounding area for adequate draining.

SOIL

COMPACTION3

E. Apply a high-quality weed and turf killer to the lawn installation area.

F. Determine if additional supplies are needed to prevent damage from weeds, rodents or ground animals. Weed barrier and rodent wire (similar to chicken wire) may be appropriate (this is not always necessary in arid or dry climates).

A. A crushed stone base of 2 - 6 in. should be spread evenly over the prepared area.

B. If using heavy equipment to do so, the equipment should not drive directly upon the prepared site. If it is unavoidable, the operator needs to be cautious of turns that can damage the base.

C. The crushed stone should be a D.O.T. Class 2 aggregate or equivalent with maximum particle size of ¾ in. or approved equal. Class 2 aggregate is available in most areas.

D. The crushed stone should be spread evenly, as smoothly as possible. Use of a finer material will help to aid final grade.

E. For the depth of the base as a rule of thumb, in arid climates such as Las Vegas, Phoenix or San Diego, 2 in. of base course is sufficient.

In climates with more rainfall or a higher water table, such as Seattle, New Orleans, or Houston, up to 6 in. may be necessary.

F. Lightly spray your surface with water and then firmly compact the sub-base using a hand compactor, landscape roller or vibratory plate compactor.

G. Check for surface depressions. If the base course layer is not as smooth as desired, or there are undesired undulations, it may be necessary to add a layer of fines (stone dust, screenings manufactured sand, etc.) to fill in the low spots or create a level surface.

This layer should be kept to a minimum, preferably no more than 2 in. This layer must be compacted with a heavy roller or plate compactor. Fill in and re-level any base depression that is more than ¼ in. deep.

BASE

CONSTRUCTION4

H. Even though synthetic turf drains water vertically through drainage holes built into it, we also suggest giving the base a very slight slope, away from any buildings, to a proper drainage area to avoid any pooling at all.

I. Continual passes over the project area are required until a compaction rate of 95% or greater is achieved. When dry, the project area should be smooth and firm to eliminate unwanted bumps under the synthetic turf.

J. Add your base starting at the farthest side of the install. Go from edge to edge, not center to edge. Feather base from load to load. The base material should be spread evenly. Grade and level to meet design and drainage requirements. Shape to desired appearance — flat, slight roll, mounded.

K. A gas powered vibratory plate compactor may be rented for larger jobs. Overlap trips with the compactor to minimize ridges and bumps.

L. Do not walk on freshly laid base until it is compacted. Walking in loose base will create holes and uneven spots. An easy way to estimate proper compaction is to step onto the stone base. If you leave a footprint, the base is not compacted enough.

A. Fold the adjacent trimmed edges of two rolls of turf approximately 2 ft. apart the entire length of the seam.

B. Mark the centerline of the seam on the exposed base or seaming tape with a chalk line or spray paint.

C. Roll out seam tape centered over the entire length of the seam line. Apply adhesive, covering all of the seam tape from one end to the other. Depending on the type of adhesive used, you may need to allow time for vapors/gases to escape (flashing). Refer to the adhesive manufacturer’s directions. The flashing time required may be dependent on ambient temperature and humidity.

SEAMING6

A. Roll the synthetic turf out on top of the constructed based, as planned. If the site requires multiple roll widths, be sure to have the lay of the fibers on each roll of turf running in the same direction.

B. When seaming is required, trim the selvedge (un-tufted edge) off turf and lay in the desired position.

C. When trimming selvedge, begin cutting two tuft rows in from edge in order to achieve proper seam strength.

D. Lay the next roll adjacent to the first and repeat Step C. Then butt the seams together.

E. With a carpet or utility knife, trim the overlapped turf to match the trimmed edge of the first roll if necessary.

LAY

TURF5

F. Make all cuts as close as possible without touching. Seam spacing should be no more than 1/8 in.

G. Repeat as needed for as many roll widths as the job requires.

H. Around the borders, trim the turf to match the edges.

I. If a secured or fastened edge is desired, do not secure the edge until most of the infill is installed (Refer to Step 8). More on this later.

J. When cutting curved edges, cut in small relief cut increments to match the design.

K. Rough-cut the perimeter before any seaming.

L. Always stretch synthetic turf tight to reduce wrinkling.

D. After adhesive has flashed, lay the edges of each roll of turf directly onto the adhesive/tape, making sure not to bury any turf fibers into the adhesive.

E. Add weight (i.e. sandbags) down the length of the freshly laid seam, or use a heavy roller along the seam length once the adhesive has tacked up. The adhesive drying/curing time will vary with different adhesives dependent upon climatic conditions.

F. After the adhesive has dried, trim off your turf so your lawn fits exactly as you want.

A. You will also want to stand the turf up vertically with the power broom or stiff bristle broom prior to applying the infill. Do not use steel or wire bristle brooms that can damage the fiber. This keeps all of the turf fibers erect and exposed.

B. In synthetic turf applications, a drop spreader (commonly used to spread turf seed, fertilizer, lime, etc.) should be used to spread the infill in lifts ranging from ¼ in. to no greater than ½ in. depths.

C. Infill should be applied evenly and groomed to ensure consistent infill level.

D. If the borders or edges will be secured, save the infill installation for these areas for last.

See Step 9.

E. Be sure not to dump the infill in large quantities on the turf, this will cause excessive grooming due to trapped fibers. As you spread the infill, make one entire pass on the surface of your new lawn and then sweep the infill deeply into the fibers with a stiff bristle push broom or power broom. Repeat the infill spread/fiber brooming process until the infill is evenly spread such that no less than ½ - ¾ in.

of turf fiber tips are exposed above the level of the infill. Repeat this process until all of the infill has been spread and fallen in between the synthetic blades.

INFILL

INSTALLATION7

F. CAUTION: Too much fiber exposed (not enough infill) will cause the fibers to mat or crush with heavy foot traffic. This will lead to premature wearing of the fiber and will void the manufacturer’s warranty.

G. There may be more than one type of infill used on the same site. In many cases, a combination of silica sand and granulated rubber, or silica sand and manufactured sand topdressing, may be used in layers. In either case, the silica sand is installed first, followed by the granulated rubber or topdressing.

H. Be sure to follow the site specifications outlining the amount or depth of each infill material.

I. For a 50 - 80 oz. product, typically 4 lbs. per sqft. will be used. Heavier products may use up to 5 lbs. per sqft. The exact amount of infill will vary based on the product weight and the desired product reveal. When complete, ½ - ¾

in. of the synthetic blades should be exposed.

You may want to consider applying color coated sand as the final layer of infill to best match the local geography. As a rule of thumb you will use one 1 lb. per sqft. of colored sand.

SECURE

EDGES8

FINISH INFILL

& TOP DRESSING9

A. If a secured edge was installed, it will probably be necessary to add infill around the border.

Use the technique described in Step 7.

A. Landscape Nails and Spikes. Simply hammer landscape spikes, timber spikes, sod staples, etc. into the edge around the perimeter of the turf spaced every 4 - 8 in. (particularly if you are not planning on using an edging or curbing) The nail heads should be level with the turf backing to prevent turf from dimpling.

Afterwards, more trimming may be necessary.

B. Nailer Board. When installed next to a concrete or asphalt curb, a nailer board/synthetic lumber can be installed (preferably in Step 2, Area Preparation) by nailing the board to the curb with concrete nails. The turf can then be nailed into the top of the installed nailer board with a landscape nail. Afterward, more edge trimming of the turf maybe necessary.

The edges can be secured in a number of ways:

C. Buried Edges. Excavate a narrow trench around the border, deep enough to bury the exposed edge of the turf. Tuck the turf’s edge into the trench (additional trimming of excess turf may be necessary). Nail and backfill the excavated soil against the buried turf, and compact. The edge can then be hidden with mulch, straw, rock, etc.

D. Depending on your yard and your landscape concepts, you might install edging around your new lawn. Options are incredibly varied and include extruded curbing, 4 in. x 4 in.

timbers, natural stone, rock, metal edging and plastic edging. If you are not going to apply an edging, we suggest you hammer landscaping nails every 4 - 8 in. along the perimeter of your synthetic lawn to prevent the edges from lifting.

©2023 Shawgrass. All rights reserved. SHAWGRASS, HYDROCHILL AND K9 SAND are a registered trademarks of Shaw Industries Group, Inc., a Berkshire Hathaway Company.

11/2023 www.shawgrass.com maintenance

TURF

Introduction to Maintenance

Following these simple suggestions will significantly extend the life and performance of your product:

• Keep your turf clean

• No vehicle traffic, no heavy static loads, etc.

• Make all minor repairs to your surface promptly

• Clean surface regularly

Recommended Cleaning Products:

Enzyme Cleaners SCOE 10X. Odormute, Odoban, PET Stain-O ! and others. Follow manufacturer’s instructions for application.

These cleaners can be purchased from many online sources.

Vinegar Use 5% white distilled vinegar and irrigate it through the surface.

Green Cleaners Shaw R2X, Turf Renu or any type of cleaner that does not contain alcohol and is biodegradable, non-foaming, low suds products are best.

Degreasers and soapy cleaners These can be used, however you must completely rinse these cleaners out of the turf.

Dishwashing Liquid/household detergent Dilute dishwashing liquid (1 teaspoon/gallon) with water. Detergent (1 teaspoon/gallon) for spot cleaning.

Recommended Disinfecting Products:

Quaternary disinfectants:

Use a quaternary disinfectant such as TurfDefender-DISINFECTANT 44 to clean, disinfect, sterilize and de-odorize your turf. Follow manufactures instructions for proper disinfecting.

Stains

Polypropylene or Polyethylene fibers are amongst the most stain resistant fibers known to man. Therefore, most “stains” on Shaw Turf are not true stains but rather residues of foreign matter which must be promptly and thoroughly removed.

Most stains on polypropylene or polyethylene turf can be removed with water or soap and water. The first rule is promptness. It is much easier to clean up a fresh spill before it has time to harden. Remove any solid or paste-like deposit promptly using a dull knife or spatula-like tool. Blot up excess liquids with towels

Water Borne Residues

Most “stains” commonly associated with polypropylene or polyethylene turf can be classified as “water borne” stains. These stains are best removed using a warm mild solution of common household detergent and water.

• Brush the residue with a stiff brush (not a wire brush).

• Scrub the area with soap and water.

• Rinse the area thoroughly with clear water to remove all traces of soap.

• Dry with absorbent towels, if necessary.

A (3) three percent solution of ammonia in water may be used in lieu of household detergent for more stubborn residues or stains.

There are differences in maintenance between indoor and outdoor turf.

Outdoor Maintenance Care

Daily care is on-going care, it does not necessarily mean care each and every day. The amount and frequency of daily care is dependent on traffic c volume and type of use.

• �Use a leaf blower to remove fallen leaves and pine straw and debris regularly. These can trap moisture and prevent the turf from drying.

• Sanitize and deodorize as needed.

• Hose down liquid contaminants with clean water.

• �During winter months and rainy seasons, irrigating is not necessary. During dry summer months, irrigate surface periodically to wash away any contamination.

• �Substrates, such as concrete or wood, should be cleaned as needed. Avoid cleaners with alcohol or harsh acids as these can damage the turf blades. (Glue down installations should be cleaned and rinsed periodically).

Indoor Maintenance Care

As you can imagine, indoor care of turf will be slightly different than outdoor care. You cannot flood the indoor turf with water. Treat indoor turf the same as carpet.

Daily Care

• Remove large debris by hand or with appropriate vacuum.

• Depending on location, may be able to use a leaf blower.

• Spot clean as necessary using cleaning chemicals mentioned under the stain removal section above.

• Always rinse with water and extract remaining moisture using an appropriate vacuum.

• Use air movers or fans to reduce drying time, when needed.

Deep Cleaning

• Remove large debris by hand or with appropriate vacuum.

• Depending on location, may be able to use a leaf blower.

• Spot clean as necessary using cleaning chemicals mentioned under the stain removal section above.

• �Using a pump sprayer, dilute dish washing liquid or mild detergent in water (approximately 1 teaspoon/gallon) and spray over entire area and let dwell 10 minutes.

• �A truck mount extractor may be used to rinse with water only and extract the cleaning solution and soil from turf.

• Use air movers or fans to reduce drying time, when needed.

To Disinfect

�Use an EPA registered, recommended disinfectant, sanitizer , germicide, deodorizer for synthetic turf athletic fields. (Quaternary disinfectants are suggested but not required.)

To disinfect, follow the suggested steps below:

1) Vacuum prior to disinfecting and remove any large debris

2) Disinfect per manufacturer’s recommended application rate and time

3) Rinse turf after disinfecting with a water extraction unit. Hot water extraction is preferred

4) Use air movers or fans to reduce dry time

PLAYCOLOR 50

Safety is our number one priority, especially for children. That’s why Shawgrass created a line of synthetic turf specifically for playgrounds. Commercial playgrounds, like public parks or school playgrounds, create more traffic and this could easily create more wear on synthetic turf. Our playground turf is designed for “high use” play areas and offers the best in durability and return on investment.

321SG

Mobile User

321SG

PLAYCOLOR 50

© 2025 Shaw Integrated and Turf Solutions, Inc. SHAWGRASS is a registered trademark of Shaw Integrated and Turf Solutions, Inc., a division of Shaw Industries Group, Inc., a Berkshire Hathaway company.

04/2025

Fiber Type 100% Polyethylene

Fiber Mass 5,040 denier

Tufted Pile Height 1.5 in.

Turf Blade Color Multiple

Tufting Gauge 1/4 in.

Total Weight 78 oz/yd²

Face Weight 50 oz/yd²

Backing Matrix 28 oz/yd² Stabilized dual layered woven polypropylene/urethane

Item Number 321SG

Tufted Roll Width 15 ft.

Tufted Roll Length 100 ft.

10 YEAR LIMITED WARRANTY FOR COMMERCIAL PLAYGROUND.

*For full terms, please see the complete 10 year limited warranty for commercial playground.

All specifications are nominal and subject to standard manufacturing tolerances.

Specifications are subject to change without notice. Custom roll lengths and cuts are available upon request.

Ground Cover

Turf Blade

Turf Thatch

Base

Sub Base

Infill

TAN

LAGOON BLUE

PURPLE

BROWN

BLACK

WHITE

NAVY

MEDIUM BLUE

GREY

TERRACOTTA

VEGAS GOLD

YELLOW

GOLD

ORANGE

MAROON

CRIMSON

RED

K9 383SG K9 Serenity 384SG K9 Park

This durable and attractive line from Shawgrass offers a variety of products that can be used in a multitude of outdoor spaces. Designed to function well for residential and commercial applications and developed specifically for our furry friends, the K9 collection allows flexibility in design. This line of products is some of the strongest and most unique solutions in the industry designed with a special high flow backing system with pets in mind that results in a cleaner and odor free area. With a beautiful look and fibers that can withstand everyday use from pets and people, it’s not hard to see why this line is one of the top choices in the Shawgrass Collection.

384SG

K9 Park

10 YEAR LIMITED RESIDENTIAL WARRANTY. 10 YEAR LIMITED COMMERCIAL WARRANTY.

*For full terms, please see the complete 10 year limited residential landscape warranty and the 10 year limited commercial landscape warranty.

All specifications subject to a manufacturing tolerance of +/-5%.

Tufting gauge is the manufacturing standard. Values will change slightly during the secondary backing process.

Custom roll lengths and cuts are available upon request.

Fiber Type Polyethylene

Fiber Mass 12,600 denier 9 Ply PE Mono 4,500 denier 8 Ply PE Mono

Tufted Pile Height 1.25 in.

Turf Blade Color/Turf Thatch Color 310 Field Green/Lime/Green-Jute 320 Field Green/Olive/Green-Jute

Tufting Gauge 3/8 in.

Total Weight 74 oz/yd²

Face Weight 50 oz/yd²

Backing Matrix 24 oz/yd² High flow K9 backing matrix

Item Number 383SG

Tufted Roll Width 15 ft.

Tufted Roll Length 100 ft.

©2023 Shawgrass. All rights reserved. SHAWGRASS is a registered trademark of Shaw Industries Group, Inc., a Berkshire Hathaway Company.

4/2023

Turf Blade

Flow-Through Backing

Sand Infill

Flow-Through Drainage System

PET / k9 185 S. Industrial Blvd. • Calhoun, GA 30701 • www.shawgrass.com • 1-800-441-7429

1/20/2017

Planning

Be sure to speak with your architect and/or project manager/ engineer to ensure appropriate permits are obtained prior to installation. Take into consideration:

• �Drainage plan—Installation of your synthetic turf may impact drainage in the project area. Your drainage method should be specified by the architect or project manager/ engineer. A slope of 2% will generally be adequate for drainage. The turf should be sloped away from buildings when possible.

• �You may wish to install a watering or irrigation system to wash away pet urine and provide cooling.

Materials

• Shawgrass K9 Park synthetic turf. K9 Park

384SG Specification Sheet

• Woven filter fabric or geotextile.

• Infill. K9 Sand, Envirofill Pet Safe, Hydrochill® pre-coated infill.

• Seam tape and adhesive.

• Composite material or pressure treated lumber for border.

• Galvanized nails or other method to secure turf to nailer boards.

PET/K9 WITH

VERTICAL DRAINAGE

Base

Base preparation for a Pet/K9 installation is very similar to a standard turf installation with several important exceptions outlined below. Two to six inches of turf and soil should be excavated to allow installation of the base material. After excavation, the soil should be compacted using a plate compactor or hand compactor.

The base material used in pet installations should be a material that will allow vertical drainage of the turf and infill.

This will allow water to rinse away urine and other pet residues and minimize odors. The bottom base material should consist of approximately two inches of clean coarse stone with a diameter between 1 inch and ¾ inch. This material is often described as #57 stone and may be pro-duced from gravel, granite, limestone, dolomite, sandstone or other local natural stone. This bottom coarse base layer should be smoothed and then compacted to a compaction of 95% or greater.

SUPPLEMENTAL

INSTALLATION GUIDE

https://sg.bloomfire.com/posts/5011857-k9-sand-spec-sheet https://sg.bloomfire.com/posts/4892773-k9-collection https://sg.bloomfire.com/posts/4894127-hydrochill https://sg.bloomfire.com/posts/5011857-k9-sand-spec-sheet https://sg.bloomfire.com/posts/5045910-envirofill-safeshell-landscape https://sg.bloomfire.com/posts/4894127-hydrochill

5/18/2023

A layer of approximately two inches of smaller washed stone between 3/8 inch and 1/8 inch diameter should be added over the coarse stone layer. This size base material is often described as #89 stone, and as before may vary in composition based on local availability. The base should be again compacted to 95% compaction or better.

It is important that ordinary “crusher run” or “road base” material NOT be used as base material because it will include a stone dust and may inhibit vertical drainage.

If an infill material will be used, the final step in the preparation of the turf base is the installation of a woven textile filter fabric. The purpose of this fabric is to minimize migration of turf infill into the underlay material through the turf drain holes. The fabric should be overlaid on the fabric edges during this process.

concrete curb concrete screw nailer board (pressure treated or composite)

1" - 2" galvanized nail

#89 crushed stone (washed stone 3/8" to 1/8") turf blade turf thatch sub-base

#57 crushed stone (clean 1" to 3/4")

2-4 lbs.

(optional K9 Sand) geo textile (optional)

Installation Installation will be similar to normal turf installations. The turf should be secured using seam tape and adhesive at all turf seams. The turf should also be secured along all edges using nails or adhesive as you would with a normal nailer board or concrete border.

Infill (Optional) K9 sand is a biogenic, safe, renewable, and sustainable alternative to standard infills. It spreads easily and evenly intoturf; contains no microplastics. K9 Sand is dust free, silica free, and quartz free. K9 sand is a safe, effective, and non-toxic infill, perfect for your beloved K9! *Available in 50 lb.bags

Envirofill infill with Microban® can be used for pet applications. Envirofill will help to minimize urine odor as well as inhibit the growth of bacteria, mold and mildew.

Approximately 2 to 3 pounds of infill per square foot should be added to the turf. Envirofill can be supplemented with normal silica sand if necessary, but the benefits of the Envirofill infill will be reduced.

5/18/2023 ground cover (taper to height of thatch)

1.5"-2" screw for nailer board stake for nailer board

(pressure treated or composite) nailer board (pressure treated or composite)

1" - 2" galvanized nail turf blade turf thatch sub-base geo textile (optional)

#89 crushed stone (washed stone 3/8" to 1/8")

#57 crushed stone (clean 1" to 3/4")

2-4 lbs.

(optional K9 Sand)

Brock USA LLC www.brockusa.com

May 2019

Typical Properties & Specification

Product Number SP20XL

Material Type Expanded polypropylene composite containing approximately 30% by volume reprocessed pre-consumer and/or post-consumer recycled material

Part Format Interlocking panel Part Size, nominal net coverage 21.0 sq. ft per panel (1.95 sq. m) Part Thickness, nominal 0.79 in (20 mm) Part Length, nominal 67.25 in (1708 mm) Part Width, nominal 47.5 in (1207 mm) Part Weight, nominal 5.0 lb per panel

Property (Shock Pad Only) Typical Value Specification Test Method

Tensile Strength 72 psi > 45 psi ASTM D3574, Test E

Tensile Elongation 20% > 10% ASTM D3574, Test E

Compression Strength

@ 25% strain

@ 50% strain

32 psi

50 psi

> 25 psi

> 40 psi

ASTM D3575, Test D

Compression Set

35 psi for 30 minutes – % set after 24 hr

4%

< 7% Brock Test Method

Coefficient of Linear Thermal Expansion per 1 °C change

0.06 mm/m

< 0.10 mm/m

ASTM D696

Water Absorption

After 24 hr immersion

~1%

≤ 1%

DIN 53428

Water Permeability (Vertical Drainage) > 500 in/hr > 500 in/hr ASTM F1551: DIN 18-035, Part 6

Critical Fall Height (HIC = 1000) 0.83 m > 0.7 m ASTM F3146, Procedure A

Gmax 94 g < 120 g ASTM F355 (Missile A)

Shock Absorption 63%

65%

> 55%

> 55%

ASTM F3189 (Adv. Artificial Athlete)

EN 14808 (Artificial Athlete)

Vertical Deformation

7.5 mm

3.4 mm

< 8 mm

<4 mm

ASTM F3189 (Adv. Artificial Athlete)

EN 14809 (Artificial Athlete)

Resistance to Chemicals 1 / 2 ≤ 2 JSP Method based on ASTM F925

Microbiological Analysis bacteria resistance fungi resistance

No growth

ASTM G22

ASTM G21

Environmental Standards Testing

Heavy Metals

VOCs

SVOCs

Compliant with EPA human health standards, surface water and groundwater quality

Compliant with EPA human health standards, surface water and groundwater quality

EPA 6010B, 7470A, 7471A

EPA 8260B

EPA 8270C

California Title 22 Compliant Compliant CA Code of Regulations, Title 22, Division 4.5, Chapter 11

California Proposition 65 Certified (no listed mat’ls) Certified (no listed mat’ls) California Proposition 65

DATA ARE TYPICAL PROPERTIES ONLY. THIS DOCUMENT DOES NOT CREATE ANY WARRANTY, EXPRESS OR IMPLIED.

Patented and Patents Pending

Brock USA, LLC BrockUSA.com

Rev. B January 31, 2025

Typical Properties

Product Number PLB50XL

Material Type Expanded Polypropylene (EPP)

Product Format Panels with edge overlap

Product Thickness, nominal 2.0 in (50.8 mm)

Part Size, nominal net coverage 23.59 sq ft (2.19 sq m)

Panel Length, nominal 73.5 in (1.87 m)

Panel Width, nominal 49.0 in (1.24 m)

Panel Weight, nominal 5.6 lbs (2.6 kg)

Intended Use Synthetic turf playground surface systems with fall heights up to 9 ft*

Property Value Test Method

Tensile Strength† 55 psi

ASTM D3575, Suffix T

Tensile Elongation† 16%

Compression Strength†

22 psi ASTM D3575, Suffix D

Water Permeability 2115 in/hr EN 12616

Linear Thermal Expansion† per 1o C change

0.08 mm/m

Thermal Conductivity 0.397 BTU·in / hr·ft2·°F

ASTM C518

Thermal Resistance (R-Value) 5.03 ft2·°F·hr / BTU

Water Absorption†

0.0081 g/cc ASTM C272

Linear Thermal Expansion† per 1o C change

0.08 mm/m

Flammability† Pass (< 100 mm/min) FMVSS 302

Resistance to Chemicals†

(various oils, solvents, and acid/alkali solutions)

≤ 2

(no significant swelling or dissolution) JSP Method based on ASTM F925

Microbiological Analysis† no growth

ASTM G22-76

ASTM G21-96

Environmental Standards

Cradle to Cradle Certified

Cradle to Cradle Products Innovation Institute

Heavy Metals / Mercury

VOC’s

SVOC’s

Compliant to EPA human health standards, surface water quality, groundwater quality

EPA 6010B, 7470A, 7471A

EPA 8260B, EPA 8270C

California Title 22 Compliant

COEHHA Proposition 65 Compliant

DATA ARE TYPICAL PROPERTIES ONLY. THIS DOCUMENT DOES NOT CREATE ANY WARRANTY, EXPRESS OR IMPLIED The Brock PowerBase product group includes the PowerBase PLAY, PowerBase PRO, and PowerBase YSR families of products.

*Critical fall height (CFH) depends on the entire installed system (base, pad, turf, and infill). The complete system should be independently tested in accordance with ASTM F1292 to ensure the system meets any applicable performance requirements. A system may achieve a higher or lower CFH than the value shown here.

†Properties of molded EPP base material.

US and international patents and patents pending. www.brockusa.com https://www.brockusa.com/

Brock USA, LLC BrockUSA.com

Rev. A January 31, 2025

Typical Properties

Product Number PLB80XL

Material Type Expanded Polypropylene (EPP)

Product Format Panels with edge overlap

Product Thickness, nominal 3.15 in (80 mm)

Part Size, nominal net coverage 23.59 sq ft (2.19 sq m)

Panel Length, nominal 73.5 in (1.87 m)

Panel Width, nominal 49.0 in (1.24 m)

Panel Weight, nominal 8.0 lbs (3.6 kg)

Intended Use Synthetic turf playground surface systems with fall heights up to 12 ft*

Property Value Test Method

Tensile Strength 52.9 psi

ASTM D3575, Suffix T

Tensile Elongation 18%

Compression Strength

19 psi ASTM D3575, Suffix D

Water Permeability 1877 in/hr EN 12616

Linear Thermal Expansion per 1 °C change

0.081 mm/m TSM5725G (modified, -30 to 30 °C)

Thermal Conductivity 0.478 BTU·in / hr·ft2·°F

ASTM C518

Thermal Resistance (R-Value) 6.5 ft2·°F·hr / BTU

Water Absorption† 0.0081 g/cc ASTM C272

Flammability† Pass (< 100 mm/min) FMVSS 302

Resistance to Chemicals†

(various oils, solvents, and acid/alkali solutions)

≤ 2

(no significant swelling or dissolution) JSP Method based on ASTM F925

Microbiological Analysis†

ASTM G22-76

ASTM G21-96

Environmental Standards

Cradle to Cradle Certified

Cradle to Cradle Products Innovation Institute

Heavy Metals / Mercury

VOC’s

SVOC’s

Compliant to EPA human health standards, surface water quality, groundwater quality

EPA 6010B, 7470A, 7471A

EPA 8260B, EPA 8270C

California Title 22 Compliant

COEHHA Proposition 65 Compliant

DATA ARE TYPICAL PROPERTIES ONLY. THIS DOCUMENT DOES NOT CREATE ANY WARRANTY, EXPRESS OR IMPLIED.

The Brock PowerBase product group includes the PowerBase PLAY, PowerBase PRO, and PowerBase YSR families of products.

*Critical fall height (CFH) depends on the entire installed system (base, pad, turf, and infill). The complete system should be independently tested in accordance with ASTM F1292 to ensure the system meets any applicable performance requirements. A system may achieve a higher or lower CFH than the value shown here.

†Properties of molded EPP base material.

US and international patents and patents pending. www.brockusa.com https://www.brockusa.com/