Statement of Work.pdf

v4.10_DECEMBER2025

STATEMENT OF WORK (SOW)

Repair Material

1.0 Background

The Sensors and Arrays Division (Code 153) of the Naval Undersea Warfare Center Division, Newport (NUWCDIVNPT) is comprised of The Towed Array Handling Equipment Facility (TAHEF), which is the Naval Sea Systems Command (NAVSEA) certified Designated Overhaul Point for the OK-542 Thinline Towed Array Handling Equipment (TLTAHE).

NUWCDIVNPT, Code 153, requires the procurement of custom designed (build-to-print) Capstan Drive Assembly (Unit 1) and Stowage Drum/Level Wind Assembly (Unit 2).

1.1 Places of Performance

The contractor’s facilities.

1.2 Authorized Users

Code 1534 / TAHEF

1.3 Sponsors

NUWCDIVNPT

1.4 Types of Funding

Service Cost Center (SCC) Funds

2.0 Scope

The contractor shall manufacture and deliver Unit 1 and Unit 2 support material required for upgrades on Government infrastructure.

3.0 Applicable Documents

The contractor shall perform the tasking required in Section 4.0 in accordance with (IAW) the below Applicable Documents (ADs).

Table:

NUMBER TITLE REVISION/

DATE

APPLICABLE

SOW TASK

3.1 53X-01-101_32386_FN_N N/ 6-21-2012 4.1

3.2 53X-01-102_32386_FN_P P/ 6-21-2012 4.2

3.3 53X-01-132_32386_FN_M 4.3

3.4 53X-01-137_32386_FN_K 4.4

3.5 53X-01-139_32386_FN_K_D15-010 4.5

3.6 53X-01-142_32386_FN_K K/ 10-26-

4.6

3.7 53X-01-144_32386_FN_E 4.7

3.8 53X-01-165_32386_FN_L 4.8

3.9 53X-01-166_32386_FN_J 4.9

3.10 53X-01-178_32386_FN_K 4.10

3.11 53X-01-182_32386_FN_M_D02-226 4.11

3.12 53X-01-184_32386_FN_M 4.12

3.13 53X-01-185_32386_FN_E 4.13

3.14 53X-01-186_32386_FN_H 4.14

3.15 53X-01-187_32386_FN_F 4.15

3.16 53X-01-192_32386_FN_L 4.16

3.17 53X-01-198_32386_FN_E 4.17

3.18 53X-01-207_32386_FN_E 4.18

3.19 53X-01-227_32386_FN_H 4.40

3.20 53X-01-229_32386_FN_G 4.19

3.21 53X-01-258_32386_FN_F 4.20

3.22 53X-01-259_32386_FN_G 4.21

3.23 53X-02-203_32386_FN_H 4.22

3.24 53X-02-221_32386_FN_H 4.23

3.25 53X-02-222_32386_FN_G 4.24

3.26 53X-02-281_32386_FN_F_D22-039 4.25

3.27 53X-07-114_32386_FN_F 4.3

3.28 53Z-01-131_53711_FN_D D/ 5-18-2021 4.26

3.29 53Z-01-188_53711_FN_D 4.27

3.30 53Z-01-189_53711_FN_D 4.28

3.31 53Z-01-190_53711_FN_E 4.29

3.32 53Z-01-191_53711_FN_E 4.30

3.33 53Z-01-212_53711_FN_D 4.31

3.34 53Z-01-213_53711_FN_F 4.32

3.35 53Z-01-230_53711_FN_E_D17-030 4.41

3.36 53Z-01-247_53711_FN_D 4.42

3.37 53Z-01-248_53711_FN_C 4.33

3.38 53Z-01-248-W_53711_FN_E 4.33

3.39 53Z-01-249_53711_FN_B 4.34

3.40 53Z-01-249-W_53711_FN_E 4.34

3.41 53Z-01-250_53711_FN_F 4.35

3.42 53Z-01-251_53711_FN_F 4.42

3.43 53Z-01-252_53711_FN_F 4.43

3.44 53Z-01-252-W_53711_FN_D 4.43

3.45 53Z-01-255_53711_FN_E 4.36

3.46 53Z-01-255-W_53711_FN_D 4.36

3.47 53Z-01-256-1_53711_FN_D 4.43

3.48 53Z-01-256-2_53711_FN_D 4.36, 4.43

3.49 53Z-01-256-3_53711_FN_D 4.43

3.50 53Z-01-256-4_53711_FN_D 4.43

3.51 53Z-01-256-5_53711_FN_D 4.43

3.52 53Z-01-256-6_53711_FN_D 4.36

3.53 53Z-01-256-7_53711_FN_D 4.36

3.54 53Z-01-256-8_53711_FN_D 4.36

3.55 53Z-01-256-9_53711_FN_D 4.36

3.56 53Z-01-257_53711_FN_C 4.37

3.57 53Z-02-201_53711_FN_C 4.38

3.58 53Z-02-254_53711_FN_C_D11-028 4.39

3.59 6878901_53711_FN_- 4.40

3.60 6878906_53711_FN_- 4.41

3.61 6878907_53711_FN_- 4.42

3.62 6878908_53711_FN_- 4.43

3.63 7443666_53711_FN_B 4.44

3.64 8828004_53711_FN_- 4.45

3.65 8828005_53711_FN_- 4.46

3.66 8828006_53711_FN_- 4.47

3.67 8828008_53711_FN_- 4.48

3.68 8828010_53711_FN_- 4.49

3.69 8828013_53711_FN_- 4.50

3.70 8828015_53711_FN_- 4.51

3.71 8828016_53711_FN_- 4.52

3.72 8828017_53711_FN_- 4.53

3.73 53X-00-0003_32386_FN_B 4.33 and 4.34

3.74 53Z-00-0001_88594_FN-_D07-050 4.1 thru 4.39, omit 4.37

3.75 0551A0006_54497_FN_D_D07-066 All

3.76 6658982_53711_PA_A All

3.77 ASME Y14.5-2018_2019-02-11 All

3.78 ASTM A36-A36M-19_2019_07_01 4.1, 4.2, 4.17

and 4.42

3.79 ASTM A108-24_2024-03-01 4.36, 4.43, and

4.50

3.80 ASTM A240-A240M-25_2025-05-19 4.45

3.81 ASTM A276-A276M-24a_2024-02-01 4.13 and 4.45

3.82 ASTM A514_A514M_2026-01-08 4.25

3.83 ASTM A572_A572M_2026-01-08 4.25

3.84 AWS A2.4-2020_2020-01-09 All weldments

3.85 MIL-C-15726F_with_Amendment-

1_1991-10-08

4.3, 4.6, 4.8, 4.9, 4.10, 4.11. 4.21, 4.23, 4.24, 4.27 thru 4.34, 4.36, 4.39, 4.44 and 4.46

3.86 MIL-DTL-11195H_2023-02-14 4.5, 4.14, 4.17,

4.19 and 4.25

3.87 MIL-DTL-15024G_2018-03-03 All

3.88 MIL-DTL-24441-29B(SH)_2009-08-27 All

3.89 MIL-PRF-

16173E(SH)_with_INT_AMEND- 2_2017_10_19

All

3.90 MIL-PRF-23236D_with Amendment

1_2023-03-20 (MIL-P-23236)

All

3.91 MIL-STD-22D_1991.03.21 All

3.92 MIL-STD-130N_with_Change-1_2012-

11-16 All

3.93 MIL-STD-2035A(SH)_1995-05-15 All

3.94

QQ-N-281D_with_Amendment-2_1985- 10-23

4.3, 4.6, 4.8, 4.9, 4.10, 4.11. 4.21, 4.23, 4.24, 4.27 thru 4.34, 4.36, 4.39, 4.44 and 4.46

3.95 QQ-N-286G_2000-12-07 4.16 and 4.18

3.96 S9074-AQ-GIB-010-248_1995-08-01 All weldments

3.97 S9074-AR-GIB-010-278_CHG-A_2013-

02-14 (MIL-STD-278)

All weldments

3.98 SAE AMS2460B_2023-02-01 All

3.99 SAE AMS2700F_2018-03-01 4.7 and 4.22

3.100 SAE AMS-QQ-N-290D_2021-10-01 All

3.101 SAE AMS-STD-

595A_with_Amendment_3_2022-05-01 All

3.102

T9074-AS-GIB-010-271-1_MIL-

271_2014-09-11

4.1, 4.2, 4.3, 4.5, 4.10, 4.11, 4.12, 4.19, 4.20, 4.25, 4.26, 4.27, 4.28, 4.33, 4.34, 4.35, 4.36, 4.40, 4.41, 4.42, 4.43, 4.44, 4.45, 4.47, 4.48, 4.50, 4.52 and 4.53

3.103 TT-C-490J_2024-09-06 All

4.0 Technical Requirements

The contractor shall perform the tasks delineated in Section 4.1 through Section 4.53 in accordance with the Applicable Documents in Section 3.0 and using Government Furnished Information (GFI) listed in Section 6.0. The contractor shall deliver completed material as it is completed in accordance with tasks designated in Section 4.1 through Section 4.53.

4.1 In accordance with Applicable Document 3.1, the contractor shall fabricate two (2) Drive

Drum Mount, Hub Bodies (P/N: 53X-01-101).

4.1.1 The contractor shall disregard Note 9 and 10 of Applicable Document 3.1 and prepare and paint as stated in the steps below:

4.1.1.1 Plug & Protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.1.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.1.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.1.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.1.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.1.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130. Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.1.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.1.1.8 Protect all machined and painted surfaces during handling & transportation.

4.2 In accordance with Applicable Document 3.2, the contractor shall fabricate two (2) Idler Drum Mounting Hub (P/N: 53X-01-102).

4.2.1 The contractor shall disregard Note 6 of Applicable Document 3.2 and prepare, and paint as stated in the steps below:

4.2.1.1 Plug & Protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.2.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.2.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.2.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.2.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.2.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130. Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.2.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.2.1.8 Protect all machined and painted surfaces during handling &

4.3 In accordance with Applicable Document 3.3 and 3.27, the contractor shall fabricate one (1)

Outlet Guide (P/N: 53X-01-132).

4.3.1 The contractor shall disregard Note 9 of Applicable Document 3.3 and prepare, and paint as stated in the steps below:

4.3.1.1 Plug & protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.3.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.3.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.3.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.3.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.3.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130. Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.3.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.3.1.8 Protect all machined and painted surfaces during handling &

4.4 In accordance with Applicable Document 3.4, the contractor shall fabricate one (1) Scope

Sensor Ring (P/N 53X-01-137).

4.4.1 The contractor shall disregard Note 6 of Applicable Document 3.4 and prepare and paint as stated in the steps below:

4.4.1.1 Plug & Protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.4.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.4.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.4.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.4.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.4.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130. Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.4.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.4.1.8 Protect all machined and painted surfaces during handling &

4.5 In accordance with Applicable Document 3.5, the contractor shall fabricate two (2) Scope Sensor Bracket (P/N 53X-01-139).

4.5.1 The contractor shall disregard Note 6 and 9 of Applicable Document 3.5 and prepare, and paint as stated in the steps below:

4.5.1.1 Plug & protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted or prime only. Reference notes on provided drawings.

4.5.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.5.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.5.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.5.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.5.1.6 After painting is completed, disregard note 7 and stencil with white enamel IAW MIL-DTL-11195. Reference notes on drawing provided and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

NOTE: Cage code has changed to 53711.

4.5.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.5.1.8 Protect all machined and painted surfaces during handling &

4.6 In accordance with Applicable Document 3.6, the contractor shall fabricate two (2) Outlet Guide Clamp (P/N 53X-01-142).

4.6.1 The contractor shall disregard Note 6 of Applicable Document 3.6 and prepare and paint as stated in the steps below:

4.6.1.1 Plug & Protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.6.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.6.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.6.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.6.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.6.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130. Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.6.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.6.1.8 Protect all machined and painted surfaces during handling &

4.7 In accordance with Applicable Document 3.7, the contractor shall fabricate twelve (12) Retainers (P/N 53X-01-144).

4.7.1 The contractor shall disregard Note 5 of Applicable Document 3.7 and prepare and paint as stated in the steps below:

4.7.1.1 Plug & Protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.7.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.7.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.7.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.7.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.7.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130. Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.7.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.7.1.8 Protect all machined and painted surfaces during handling &

4.8 In accordance with Applicable Document 3.8, the contractor shall fabricate six (6) Torsion

Spring Bracket (P/N 53X-01-165).

4.8.1 The contractor shall disregard Note 5 and 6 of Applicable Document 3.8 and prepare and paint as stated in the steps below:

4.8.1.1 Plug & Protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.8.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.8.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.8.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.8.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.8.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130. Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.8.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.8.1.8 Protect all machined and painted surfaces during handling &

4.9 In accordance with Applicable Document 3.9, the contractor shall fabricate six (6) Torsion Spring Adjustment Bracket (P/N 53X-01-166).

4.9.1 The contractor shall disregard Note 5 of Applicable Document 3.9 and prepare and paint as stated in the steps below:

4.9.1.1 Plug & Protect all internal and external threads, holes, and bores.

Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.9.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441 Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.9.1.3 Mask off all part surfaces indicated to be prime only. Reference notes on provided drawings.

4.9.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441 Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.9.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.9.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130. Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.9.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces.

Touch-up spot paint as required for any damaged locations.

4.9.1.8 Protect all machined and painted surfaces during handling &

4.10 In accordance with Applicable Document 3.10, the contractor shall fabricate two (2) Outlet Guide Bracket (P/N 53X-01-178).

4.10.1 The contractor shall disregard Note 8 of Applicable Document 3.10 and prepare and paint as stated in the steps below:

4.10.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.10.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.10.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.10.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.10.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.10.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.10.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.10.1.8 Protect all machined and painted surfaces during handling & transportation.

4.11 In accordance with Applicable Document 3.11, the contractor shall fabricate two (2) Scope Sensor Mount (P/N 53X-01-182).

4.11.1 The contractor shall disregard Note 6 of Applicable Document 3.11 and prepare and paint as stated in the steps below:

4.11.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.11.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.11.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.11.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.11.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.11.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.11.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.11.1.8 Protect all machined and painted surfaces during handling

4.12 In accordance with Applicable Document 3.12, the contractor shall fabricate one (1) Manual Rotation Plate (P/N 53X-01-184).

4.12.1 The contractor shall disregard Note 10 of Applicable Document 3.12 and

4.12.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.12.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.12.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.12.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.12.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.12.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.12.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.12.1.8 Protect all machined and painted surfaces during handling

4.13 In accordance with Applicable Document 3.13, the contractor shall fabricate two (2) Idler Wheel Bearing Cap (P/N 53X-01-185).

4.13.1 The contractor shall disregard Note 6 of Applicable Document 3.13 and prepare and paint as stated in the steps below:

4.13.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.13.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.13.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.13.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.13.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.13.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.13.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.13.1.8 Protect all machined and painted surfaces during handling

4.14 In accordance with Applicable Document 3.14, the contractor shall fabricate two (2) Idler Mounting Hub Caps (P/N 53X-01-186).

4.14.1 The contractor shall disregard Note 5 of Applicable Document 3.14 and prepare, and paint as stated in the steps below:

4.14.1.1 Plug & protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted or prime only. Reference notes on provided drawings.

4.14.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.14.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.14.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.14.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.14.1.6 After painting is completed, disregard note 5 and stencil with white enamel IAW MIL-DTL-11195. Reference notes on drawing provided and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

NOTE: Cage code has changed to 53711.

4.14.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.14.1.8 Protect all machined and painted surfaces during handling

4.15 In accordance with Applicable Document 3.15, the contractor shall fabricate two (2)

Drive Wheel Bearing Caps (P/N 53X-01-187).

4.15.1 The contractor shall disregard Note 6 of Applicable Document 3.15 and prepare and paint as stated in the steps below:

4.15.1.1 Plug & Protect all internal and external threads, holes, and

Reference notes on provided drawings.

4.15.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.15.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.15.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.15.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.15.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.15.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.15.1.8 Protect all machined and painted surfaces during handling

4.16 In accordance with Applicable Document 3.16, the contractor shall fabricate eight (8) Angle Cylinder Retainer (P/N 53X-01-192).

4.16.1 The contractor shall disregard Note 5 and 6 of Applicable Document 3.16 and prepare and paint as stated in the steps below:

4.16.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.16.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.16.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.16.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.16.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.16.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.16.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.16.1.8 Protect all machined and painted surfaces during handling

4.17 In accordance with Applicable Document 3.17, the contractor shall fabricate two (2) Cylinder Hold Down Plate (P/N 53X-01-198).

4.17.1 The contractor shall disregard Note 3 of Applicable Document 3.17 and prepare, and paint as stated in the steps below:

4.17.1.1 Plug & protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted or prime only. Reference notes on provided drawings.

4.17.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.17.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.17.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.17.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.17.1.6 After painting is completed, disregard Note 3 and stencil with white enamel IAW MIL-DTL-11195. Reference notes on drawing provided and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

NOTE: Cage code has changed to 53711.

4.17.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.17.1.8 Protect all machined and painted surfaces during handling

4.18 In accordance with Applicable Document 3.18, the contractor shall fabricate one (1) Handcrank Bar (P/N 53X-01-207).

4.18.1 The contractor shall disregard Note 5 of Applicable Document 3.18 and prepare and paint as stated in the steps below:

4.18.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.18.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.18.1.3 Mask off all part surfaces indicated to be prime only.

4.18.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.18.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.18.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.18.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.18.1.8 Protect all machined and painted surfaces during handling

4.19 In accordance with Applicable Document 3.20, the contractor shall fabricate two (2) Idler Roller Assembly Support (P/N 53X-01-229).

4.19.1 The contractor shall disregard Note 8 and 9 of Applicable Document 3.20 and prepare, and paint as stated in the steps below:

4.19.1.1 Plug & protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted or prime only. Reference notes on provided drawings.

4.19.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.19.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.19.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.19.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.19.1.6 After painting is completed, disregard Note 10 and stencil with white enamel IAW MIL-DTL-11195. Reference notes on drawing provided and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

NOTE: Cage code has changed to 53711.

4.19.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.19.1.8 Protect all machined and painted surfaces during handling

4.20 In accordance with Applicable Document 3.21, the contractor shall fabricate two (2) Idler Non-Lock Side Splice Plate (P/N 53X-01-258).

4.20.1 The contractor shall disregard Note 8 and 9 of Applicable Document 3.21 and prepare and paint as stated in the steps below:

4.20.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.20.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.20.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.20.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.20.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.20.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.20.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.20.1.8 Protect all machined and painted surfaces during handling

4.21 In accordance with Applicable Document 3.22, the contractor shall fabricate two (2) Drive Lock Side Splice Plate (P/N 53X-01-259).

4.21.1 The contractor shall disregard Note 5 of Applicable Document 3.22 and prepare and paint as stated in the steps below:

4.21.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.21.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.21.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.21.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.21.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.21.1.6 After painting is completed, reference notes on provided

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.21.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.21.1.8 Protect all machined and painted surfaces during handling

4.22 In accordance with Applicable Document 3.23, the contractor shall fabricate two (2) Levelwind Driven Pulley Taper Lock Bushing (P/N 53X-02-203).

4.22.1 The contractor shall disregard Note 6 of Applicable Document 3.23 and prepare and paint as stated in the steps below:

4.22.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.22.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.22.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.22.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.22.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.22.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.22.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.22.1.8 Protect all machined and painted surfaces during handling

4.23 In accordance with Applicable Document 3.24, the contractor shall fabricate two (2)

Drive Sprocket (P/N: 53X-02-221).

4.24 In accordance with Applicable Document 3.25, the contractor shall fabricate two (2) Levelwind Drive Sprocket Flange (P/N 53X-02-222).

4.24.1 The contractor shall disregard Note 5 of Applicable Document 3.25 and prepare and paint as stated in the steps below:

4.24.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.24.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.24.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.24.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.24.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.24.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.24.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.24.1.8 Protect all machined and painted surfaces during handling

4.25 In accordance with Applicable Document 3.26, the contractor shall fabricate two (2) Pressure Compensator Mounting Bracket (P/N 53X-02-281-2).

4.25.1 The contractor shall disregard Note 13 of Applicable Document 3.26 and prepare, and paint as stated in the steps below:

4.25.1.1 Plug & protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted or prime only. Reference notes on provided drawings.

4.25.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.25.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.25.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.25.1.5 Paint and primer application shall be by spraying, follow

4.25.1.6 After painting is completed, disregard Note 10 and stencil with white enamel IAW MIL-DTL-11195. Reference notes on drawing provided and mark part numbers as required in locations shown. Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

NOTE: Cage code has changed to 53711.

4.25.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.25.1.8 Protect all machined and painted surfaces during handling

4.26 In accordance with Applicable Document 3.28, the contractor shall fabricate two (2) Inlet Guide (P/N 53Z-01-131).

4.26.1 The contractor shall disregard Note 5 of Applicable Document 3.28 and prepare and paint as stated in the steps below:

4.26.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.26.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.26.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.26.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.26.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.26.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.26.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.26.1.8 Protect all machined and painted surfaces during handling

4.27 In accordance with Applicable Document 3.29, the contractor shall fabricate two (2) Idler Roller Bottom Mounting Plate (P/N 53Z-01-188).

4.27.1 The contractor shall disregard Note 3 of Applicable Document 3.29 and

4.27.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.27.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.27.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.27.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.27.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.27.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.27.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.27.1.8 Protect all machined and painted surfaces during handling

4.28 In accordance with Applicable Document 3.30, the contractor shall fabricate two (2) Idler Roller Top Mounting Plate (P/N 53Z-01-189).

4.28.1 The contractor shall disregard Note 3 of Applicable Document 3.30 and prepare and paint as stated in the steps below:

4.28.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.28.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.28.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.28.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.28.1.5 Paint and primer application shall be by spraying, follow

4.28.1.6 After painting is completed, reference notes on provided

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.28.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.28.1.8 Protect all machined and painted surfaces during handling

4.29 In accordance with Applicable Document 3.31, the contractor shall fabricate two (2) Push Roller Bottom Side Plate (P/N 53Z-01-190).

4.29.1 The contractor shall disregard Note 3 of Applicable Document 3.31 and prepare and paint as stated in the steps below:

4.29.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.29.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.29.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.29.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.29.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.29.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.29.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.29.1.8 Protect all machined and painted surfaces during handling

4.30 In accordance with Applicable Document 3.32, the contractor shall fabricate two (2) Push Roller Top Side Plate (P/N 53Z-01-191).

4.30.1 The contractor shall disregard Note 3 of Applicable Document 3.32 and

4.30.1.1 Plug & Protect all internal and external threads, holes, and

Reference notes on provided drawings.

4.30.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.30.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.30.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.30.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.30.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Ensure cage code numbers and part numbers are stamped or stenciled as noted in provided drawings IAW MIL-STD-130.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.30.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.30.1.8 Protect all machined and painted surfaces during handling

4.31 In accordance with Applicable Document 3.33, the contractor shall fabricate two (2) Side Plate Connector Bracket Lock Side (P/N 53Z-01-212).

4.31.1 The contractor shall disregard Note 1 of Applicable Document 3.33 and prepare and paint as stated in the steps below:

4.31.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference notes on provided drawings.

4.31.1.2 Prime with one coat (4-6mil DFT) of MIL-DTL-24441

Formula 150 Green Primer (or MIL-PRF-23236; Type V, VI, or VII; Class 5 or 7; Color Green).

4.31.1.3 Mask off all part surfaces indicated to be prime only.

Reference notes on provided drawings.

4.31.1.4 Paint with two coats (4-6mil DFT) of MIL-DTL-24441

Formula 151 Haze Gray (or MIL-PRF-23236 Equivalent).

4.31.1.5 Paint and primer application shall be by spraying, follow paint manufacturers’ application instructions.

4.31.1.6 After painting is completed, reference notes on provided drawings and mark part numbers as required in locations shown.

Laser engraving may be utilized instead of stamping. NOTE: Cage code has changed to 53711.

4.31.1.7 Vendor is required to perform visual inspection before return shipment to TAHEF – verify paint coating all required surfaces. Touch-up spot paint as required for any damaged locations.

4.31.1.8 Protect all machined and painted surfaces during handling

4.32 In accordance with Applicable Document 3.34, the contractor shall fabricate two (2) Side Plate Connector Bracket Non-Lock Side (P/N 53Z-01-213).

4.32.1 The contractor shall disregard Note 1 of Applicable Document 3.34 and prepare and paint as stated in the steps below:

4.32.1.1 Plug & Protect all internal and external threads, holes, and bores. Mask off part surfaces indicated not to be primed/painted.

Reference…