PGC 02867 TechData.doc

Updated 26 November 2024

(Trousers, APECS, MARPAT)

NSN(S) THIS PROCUREMENT

SIZE

UPC

8415-01-506-5461

XSMALL-XSHORT

718020 491714

8415-01-506-5472

SMALL-XSHORT

718020 505688

8415-01-506-5473

MEDIUM-XSHORT

718020 590608

8415-01-506-5476

XSMALL-SHORT

718020 439228

8415-01-506-5612

SMALL-SHORT

718020 522913

8415-01-506-5479

MEDIUM-SHORT

718020 110271

8415-01-506-5480

LARGE-SHORT

718020 543406

8415-01-506-5481

XSMALL-REGULAR

718020 587004

8415-01-506-5573

SMALL-REGULAR

718020 590660

8415-01-506-5490

MEDIUM-REGULAR

718020 054384

8415-01-506-5569

LARGE-REGULAR

718020 136165

8415-01-506-5575

XLARGE-REGULAR

718020 500911

8415-01-506-5613

XSMALL-LONG

718020 540993

8415-01-506-5589

SMALL-LONG

718020 494197

8415-01-506-5590

MEDIUM-LONG

718020 106458

8415-01-506-5591

LARGE LONG

718020 442228

8415-01-506-5592

XLARGE-LONG 718020 446943

8415-01-516-8421

LARGE-XLONG 718020 071015

SECTION C- DESCRIPTION/SPECIFICATION

ITEM DESCRIPTION

TROUSERS, APECS, MARPAT

PART OF THE MARINES ALL-PURPOSE ENVIRONMENTAL CLOTHING SYSTEM (APECS)

TROUSERS SHALL BE MADE IN ACCORDANCE WITH CLASS 1 OF MIL-DTL-32158, DATED 19 JANUARY 2004.

PATTERN DATE: 19 MARCH 2020

SHADE STANDARD SAMPLE MIL-DTL-32142, DATED 23 DECEMBER 2003 IS AVAILABLE UNDER ROLL #3974. FOR SHADE, APPEARANCE, and nIR.

DEVIATIONS/CHANGES TO MIL-DTL-32158 DATED 19 JANUARY 2004:

PAGE 3, PARAGRAPH 2.3, AFTER LINE 11, ADD “ASTM D-4032 STANDARD TEST METHOD FOR STIFFNESS OF FABRIC BY CIRCULAR BEND PROCEDURE”

PAGE 4, DELETE “TECHNICAL ASSOCIATION OF THE PULP AND PAPER INDUSTRY (TAPPI);

TAPPI METHOD T-451-FLEXURE PROPERTIES OF PAPER (CLARK STIFFNESS); (APPLICATIONS FOR COPIES OF REFERENCED DOCUMENTS SHOULD BE ADDRESSED TO TAPPI PRESS, TECHNOLOGY PARK/ATLANTA, PO BOX 105113, ATLANTA, GA 30348-5113.)”

PAGE 5, TABLE I, CHARACTERISTICS, STIFFNESS, DELETE “CM” AND SUBSTITUTE “POUNDS FORCE.”

PAGE 5, TABLE I, STIFFNESS REQUIREMENTS, DELETE “WARP – 11.0 MAX; FILLING - 11.0 MAX.” AND SUBSTITUTE “WARP – 3.0 MAX; FILLING - 3.0 MAX.”

PAGE 7, TABLE IV, STIFFNESS CHARACTERISTICS, DELETE “CM” AND SUBSTITUTE “POUNDS FORCE.”

PAGE 7, TABLE IV, STIFFNESS REQUIREMENTS, DELETE “8.0” AND SUBSTITUTE “3.0”

PAGE 8, TABLE VI, LEG TABS HOOK, DELETE " 1-1/2 INCHES LENGTH" AND SUBSTITUTE "1-3/8 INCHES LENGTH"

PAGE 8, PARAGRAPH 3.3.9, LINE 6, DELETE “PARAGRAPH 2.2.7 OF A-A-55634" AND SUBSTITUTE "TYPE III OF MIL-PRF-5038. LEG AND FLY SLIDE FASTENER THONGS FINISHED LENGTH SHALL BE 2 (+¼, -0) INCHES."

PAGE 8, TABLE VII, DELETE ENTIRELY AND SUBSTITUTE:

TABLE VII- SLIDE FASTENER LENGTHS

X-SHORT

SHORT

REGULAR

LONG

X-LONG

X-SMALL

7½

7½

7½

SMALL

7½

7½

MEDIUM

7½

LARGE

11½

X-LARGE

11½

XX-LARGE

11½

11½

11½

PAGE 9, PARAGRAPH 3.3.10, LINE 2, DELETE "ITW NEXUS PART 350-2000" AND SUBSTITUTE “YKK CORD LOCK #69150 LC05SHDM GOV CORD STOPPER OR #0089716 LC05SHDM2 GOV CORD STOPPER OR PART #64740."

PAGE 9, PARAGRAPH 3.3.11, LINE 1, AFTER "STYLE 2" ADD "A".

PAGE 10, PARAGRAPH 3.3.14.2, ADD THE FOLLOWING SIZES TO THE LABEL INFORMATION:

LARGE X-SHORT

INSEAM: UP TO 26 1/2 IN.

WAIST: 35 TO 39 IN.

STOCK NO. 8415-XX-XXX-XXXX

X-LARGE SHORT

INSEAM: 26 1/2 TO 29 1/2

WASIT: OVER 39 IN.

STOCK NO. 8415-XX-XXX-XXXX

PAGE 12, TABLE VIII, INSERT "2/" CARGO POCKET FLAP AND CARGO POCKET TAB". ADD NEW FOOTNOTE: "2/ A ONE PIECE CARGO POCKET FLAP/TAB PATTERN MAY BE USED TO REPLACE THESE PATTERN PIECES."

PAGE 12, PARAGRAPH 3.6.1, LINE 1, DELETE “ASTM-STD-751” AND SUBSTITUTE “ASTM-D-6193.”

PAGE 13, PARAGRAPH 3.7, LINE 1, DELETE “II” AND SUBSTITUTE “IX”.

PAGE 17, OPERATION 7, ADD THE FOLLOWING NEW OPERATIONS:"

OR 7.e. FOLD BUTTONHOLE TAB PORTION OF FLAP, AS INDICATED BY MARKS ON PATTERN (FABRIC BACK-TO-BACK) AND MAKE ONE VERTICAL BUTTONHOLE IN TAB AS INDICATED BY MARK ON PATTERN.

BUTTONHOLE - 52-56 PER BUTTONHOLE- B - B

7.f. FOLD TAB ON FOLD LINE, FOLD OPPOSITE RAW EDGE OF FLAP EVEN WITH RAW EDGE OF TAB INCLOSING TAB WITHIN THE FOLD, AND STITCH SIDE RAW EDGES.

301 - SSe-2(A) - 10-14 B - B 7.g. TURN FLAP AND TAB RIGHT SIDE OUT, FORCE OUT CORNERS AND EDGES. TURN FLAP AND TAB AGAIN (TO FINISHED POSITION WITH RAW EDGES HIDDEN) AND WORK OUT CORNERS AND EDGES. STITCH BOTTOM AND SIDE EDGES 1/4 INCH FROM EDGE. BOTTOM EDGE OF BUTTONHOLE TAB SHALL NOT BE CAUGHT IN THE BOTTOM EDGE STITCHING. THE BUTTONHOLE PURLING SHALL FINISH FACING THE POCKET FLAP.

301 - SSe-2(B) - 10-14 B - B"

PAGE 17, OPERATION 8.b, LINE 3, AFTER POCKET, INSERT "AS AN ALTERNATE, THE NEDS OF THE ELASTIC MAY BE LINE-TACKED TO THE FACING." UNDER STITCH TYPE, INSERT "OR LINE TACK" AND UNDER "STITCHES PER INCH, INSERT "28 PER TACK" LINE 5, ADD "THE ELASTIC IN THE CARGO POCKET OPENING SHALL EXTEND THE FULL WIDTH TO ACHIEVE A 6-3/4 TO 7-1/2 INCHES RELAXED OPENING. THE ELASTIC WILL RETREAT TO ITS RELAXED OPENING POSITION WHEN THE HAND IS REMOVED. THE ENCASED ELASTIC WEBBING FOR THE CARGO POCKET SHALL LIE FLAT IN THE RELAXED STATE AND NOT DISTORT THE TROUSER LEG."

PAGE 19, OPERATION 13.d, ADD " OR IF A ONE-PIECE FLAP CONSTRUCTION IS USED, POSITION FLAP ABOVE POCKET PER MARKS ON PATTERN AND STITCH TO TROUSERS USING TWO ROWS OF STITCHING 1/16 TO 1/8 INCH FROM FOLDED EDGE OF FLAP, 1/4 INCH APART.

301 - OSf-2 - 10-14 B - B"

PAGE 19, OPERATION 13.d (1), ADD “SEW BUTTON ON EACH CARGO POCKET TO CORRESPOND WITH THE EYELET END OF POCKET FLAP. 101 OR 301 – 14-16 PER BUTTON- B- B” PAGE 20, OPERATION 13.e, LINE 2, AFTER “FLAP’, DELETE "TO THE TROUSERS" AND INSERT "THROUGH THE POCKET AND TROUSERS".

PAGE 22, OPERATION 18.a, LINE 5, AFTER "PIECE." ADD "THE EYELET SHALL BE CENTERED IN THE WAIST HEM.”

***NOTE***DISREGARD THE PLACEMENT OF THE EYELET PER MARK ON PATTERN THAT FINISHES AT THE TOP FOLD OF THE WAIST SINCE THE EYELET IS TO BE CENTERED ON THE WAIST.

PAGE 22, OPERATION 18.a, AT END OF OPERATION, ADD:

"OR STITCH A 3/8 TO 1/2 INCH, STRAIGHT-CUT BUTTONHOLE, TACKED AT BOTH ENDS, THROUGH THE REINFORCEMENT PIECE AND TROUSERS. THE BUTTONHOLE SHALL BE CENTERED ON THE REINFORCEMENT PIECE. 304 -52-56 OR 57-60 PER BUTTONHOLE INCLUDING TACK- B - B "

PAGE 23, OPERATION 18.b, AT END OF SENTENCE ADD "AND SEAT PATCH."

PAGE 23, OPERATION 18.e, DELETE AND SUBSTITUTE "POSITION SUSPENDER LOOPS ON TROUSER FRONT WAIST HEM 2-5/8 (+/- 1/8) INCHES FROM FINISHED OUTSEAMS, FOLD UNDER RAW EDGES 3/8 INCH AND BARTACK IN PLACE WITH A 3/8 INCH VERTICAL BARTACK. THE DRAWCORD SHALL NOT BE CAUGHT IN THE BARTACKS. THE SUSPENDER LOOPS SHALL FINISH 5-1/4 +/- 1/8 INCHES IN LENGTH BETWEEN BARTACKS."

PAGE 23, OPERATION 20A. LINE 7, DELETE “3/8 TO 1/2" AND SUBSTITUTE “5/8 TO 3/4".

PAGE 24, OPERATION 20.b, LINE 5, DELETE "1-7/8" AND SUBSTITUTE "2-1/4”

PAGE 24, AFTER OPERATION 20B. DELETE ALL SIZE SPECIFIC BELT LOOP PLACEMENT LANGUAGE AND SUBSTITUTE:

“SIZES: ALL SIZES

POSITION 7 EVENLY SPACED BELT LOOPS ON TROUSER WAIST WITH ONE ON OR ADJUNCT TO CENTER BACK JOINING SEAM. BELT LOOPS SHALL NOT INTERFERE WITH FRONT PASS-THRU OPENING FLAP.”

PAGE 25, OPERATION 22, LINE 2, DELETE "THONGS" AND SUBSTITUTE "FLY THONG."

PAGE 25, TABLE X: ADD:

"X-SHORT, LARGE 1/2 WAIST - 21; INSEAM 26 1/2; OUTSEAM 38

SHORT, X-LARGE 1/2 WASIT - 23; INSEAM 28 1/2; OUTSEAM 40"

PAGE 25, TABLE X, LARGE, X-LONG, OUTSEAM, DELETE "46" AND SUBSTITUTE "48"

PAGE 27, LINE 3, UNDER TEST METHOD, STIFFNESS, DELETE “TAPPI-T-451 7/” AND SUBSTITUTE “ASTM D4032”

PAGE 27, LINE 4, UNDER TEST METHOD FOR "PUNCTURE PROPAGATION TEAR" DELETE "ASTM D 2852 8/" AND SUBSTITUTE "ASTM D 2582 8/" PAGE 27, LINE 11, UNDER CLOTH, THREE-LAYER KNIT, TEST METHOD, STIFFNESS, DELETE “TAPPI-T-451” AND SUBSTITUTE “ASTM D4032” PAGE 27, TABLE XI, UNDER CLOTH, THREE-LAYER KNIT, TEST METHOD FOR HYDROSTATIC RESISTANCE, "(INITIAL TAFFETA RESTRAINT), DELETE FOOTNOTE "1/"

PAGE 27, TABLE XI, (AFTER DEET TAFFETA RESTRAINT), DELETE "ASTM-D-3393 1/" AND SUBSTITUTE "ASTM-D-751 1/"

PAGE 27, TABLE XI, UNDER (SEAM SEALING TAPE) MOVE DOWN ONE LINE "3.3.3 4.5.2.1(B)" DELETE "(B)" AND SUBSTITUTE "(A)"; MOVE DOWN ONE LINE "3.3.3 ASTM-D-3776"; DELETE "WEIGHT" AND SUBSTITUTE: "TAPE END INTEGRITY AND ADD TEST METHOD 4.5.2.1 (A)"

PAGE 28, FOOTNOTE 4/, LINE 1, DELETE "5SO+/-" AND SUBSTITUTE "550 +/- 50”.

PAGE 28, FOTENOTE 6/, LINE 1, DELETE "4.4.7" AND SUBSTITUTE "4.5.2, EXCEPT THAT A 2 LB. LOAD SHALL BE USED AND 14 GRAMS OF DETERGENT. THE DRYING TIME SHALL BE 20 MINUTES."

PAGE 28, FOOTNOTE 7, DELETE IN ITS ENTIRETY.

PAGE 30, TABLE XII, UNDER COLUMN EXAMINE, DRAWCORD, DEFECT 210, DELETE AND SUBSTITUTE "ANY DRAWCORD CAUGHT IN BARTACK"

PAGE 30, PARAGRAPH 4.4.2, LINE FOUR, DELETE "1.5" AND SUBSTITUTE "1.0".

PAGE 33, TABLE XII, UNDER DEFECTS FOR ANKLE TAB, ADD "UNDER EDGE OF TAB EXPOSED BEYOND TOP EDGE OF TAB BY MORE THAN 1/8 INCH MINOR 242A"

PAGE 33, PARAGRAPH 4.4.3, LINE FIVE, DELETE "4.0" AND SUBSTITUTE "2.5".

PAGE 37, PARAGRAPH 6.7.2, DELETE ENTIRTY AFTER "FROM" AND SUBSTITUTE "YYK CORPORATION OF AMERICA, 1300 COBB INDUSTRIAL AVE, MARIETTA, GA- MAIN OFFICE (770) 427-5521.

DEVIATIONS/CHANGES TO A-A-50083:

PAGE 1, PARAGRAPH 1.2. DELETE SECOND SENTENCE ENTIRELY, AND SUBSTITUTE "THE THICKNESS OF THE MATERIAL SHALL BE 0.0010 TO 0.0090 INCHES IN ACCORDANCE WITH A-A-3174.

DEVIATIONS/CHANGES TO A-A-50198A:

THREAD, GIMP, COTTON, BUTTONHOLE STANDARD SAMPLE FOR COLOR FOLIAGE GREEN 504, IS MIL-C-44436, ROLL #3728, (THE FOLIAGE GREEN 502 AREA PF THE PATTERN) AND REFERENCE FOR SHADE ONLY.

DEVIATIONS/CHANGES TO A-A-50199:

STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-DTL-44436, ROLL #3728. (THE FOLIAGE GREEN 502 AREA OF THE PATTERN) AND IS REFERENCED FOR SHADE ONLY. THIS SHADE HAS BEEN APPROVED FOR TYPE I COLOR STANDARD.

DEVIATIONS/CHANGES TO A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

DEVIATIONS/CHANGES TO V-B-871: CANCELED AND REPLACED WITH A-A-59994.

DEVIATIONS/CHANGES TO MIL-DTL-10884H:

PAGE 1, PARAGRAPH 1.2, CLASSIFICATION. AFTER "FINISH 5" ADD "FINISH 6 - WHITE".

PAGE 7, PARAGRAPH 3.4.5, DELETE SENTENCES 4 AND 5 IN THEIR ENTIRETY.

PAGE 7, AFTER PARAGRAPH 3.4.5.2, ADD NEW PARAGRAPH AS FOLLOWS: "3.4.6 FINISH 6 - WHITE. REFERENCE PARAGRAPH 3.4.5 EXCEPT THE COLOR SHALL BE WHITE."

DEVIATIONS/CHANGES TO MIL-DTL-5038:

ALL STANDARD SAMPLE INFORMATION WILL STILL APPLY. STANDARD SAMPLES ARE AS FOLLOWS:

BLACK 375, TYPE III, ROLL #3443, FOR SHADE, APPEARANCE AND COLORFASTNESS.

OLIVE DRAB 7, TYPE IV, ROLL #3012, FOR SHADE, FINISH AND COLORFASTNESS.

CAMOUFLAGE GREEN 483, TYPE II, ROLL #3484, FOR SHADE, APPEARANCE AND COLORFASTNESS.

CAMOUFLAGE GREEN 483, TYPE III, ROLL #3485 FOR SHADE, APPEARANCE AND COLORFASTNESS.

CAMOUFLAGE GREEN 483, TYPE IV, ROLL #3486, FOR SHADE, APPEARANCE AND COLORFASTNESS.

DEVIATIONS/CHANGES TO MIL-T-3530: CANCELED AND REPLACED WITH A-A-59991.

DEVIATIONS/CHANGES TO MIL-W-5664D:

PAGE 3, PARAGRAPH 3.3.1 - DELETE IN ITS ENTIRETY AND SUBSTITUTE: "3.3.1 WEAVE CONSTRUCTION. THE WEAVE FOR ALL TYPES AND CLASSES MAY BE SUPPLIED IN EITHER SHUTTLE OR SHUTTLELESS LOOM CONSTRUCTION.

PAGE 4, PARAGRAPH 3.7, SENTENCE 2, DELETE IN ITS ENTIRETY AND SUBSTITUTE "TYPE II SHALL BE CAMOUFLAGE GREEN 483.

PAGE 5, PARAGRAPH 4.6.1.1 YARD-BY-YARD EXAMINATION, CONTINUED ON PAGE 6, LINE 2, DELETE "2.5" AND SUBSTITUTE "1.5.". LINE 3, DELETE "6.5" AND SUBSTITUTE "4.0"

PAGE 8, TABLE II - DELETE THE DEFECT FOR "YARNS (FILLING)" ENTIRELY.

PAGE 10, PARAGRAPH 4.6.3 - DELETE IN ITS ENTIRETY.

STANDARD SAMPLE FOR FOLIAGE GREEN 504, WEBBING, TEXTILE, ELASTIC, IS IDENTIFIED AS ROLL NO. 3743, REFERENCED FOR SHADE ONLY.

STANDARD SAMPLE FOR CAMOUFLAGE GREEN 483 IS IDENTIFIED AS ROLL NO. 3523, REFERENCED FOR SHADE ONLY.

DEVIATIONS/CHANGES TO MIL-DTL-32072: CANCELED AND REPLACED WITH A-A-59963.

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking Omitted; incorrect; illegible, of (exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 4.0.

Examine Defect

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palletization Pallet pattern not as specified.

Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible; of improper size, location, sequence or method of application.

DEVIATION/CHANGES TO MIL-STD-129R, WITH CHANGE 3, DATED 25 FEBRUARY 2023

DEVIATION/CHANGES TO MIL-STD-147E WITH CHANGE 3, DATED 05 SEPTEMBER 2024

DEVIATION/CHANGES TO ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED. APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

SECTION D – PACKAGING AND MARKING

CASE LOT QUANTITY OF 15 TROUSERS OF ONE SIZE.

THE TROUSERS SHALL BE FOLDED, WITH LABELS VISABLE, THE TROUSERS SHALL BE PLACED IN A CLOSE-FITTING CLEAR POLYETHYLENE BAG CONFORMING TO A-A-50083 OR A COMMERCIALLY ACCEPTABLE BAG. THE BAG SHALL HAVE A ¼ INCH HOLE LOCATED NEAR A BOTTOM CORNER TO ALLOW AIR TO ESCAPE. AS AN ALTERNATE TO THE SPECIFIED CLOSURE, A FLAP AND REVERSE TUCK MAY BE USED.

SHADE EVALUATION IS REQUIRED ON EACH LOT. SAMPLE SIZE SHALL BE 24 X FULL WIDTH.

SAMPLES SHALL BE RANDOMLY SAMPLED FROM THE LOT AND SENT TO US ARMY CCDC SOLDIER CENTER

10 General Green Ave

Attn: Rachel Matuszek, TMET Bldg 5

Natick, MA 01760

PHYSICAL TEST REPORTS SHALL BE SENT TO US ARMY CCDC SOLDIER CENTER

10 General Green Ave

Attn: Rachel Matuszek, TMET Bldg 5

Natick, MA 01760

END ITEM TESTING IS REQUIRED IN ACCORDANCE WITH MIL-DTL-32158, DATED 19 JANUARY 2004.

AS A MINIMUM ITEMS SHALL BE PACKED IN A SNUG FITTING FIBERBOARD SHIPPING CONTAINER, MINIMUM BURST STRENGTH 275 psi (ECT 44), CONFORMING TO ASTM-D-5118, TYPE CF, STYLE RSC, GRADE 275, VARIETY SW, CLASS DOMESTIC, WITH A DOUBLE WALL LINER. BOXES SHALL BE IN COMPLIANCE WITH THE NATIONAL MOTOR FREIGHT CLASSIFICATION. ANY COMMERCIAL CLOSURE METHOD CITIED IN ASTM-D-1974 IS ACCEPTABLE EXCEPT STAPLING.

PACKAGING SHALL BE AS PER ASTM-D-3951, MIL-STD-129R WITH CHANGE 3, MIL-STD-147E WITH CHANGE 3.

LOT NUMBERING SHALL BE IN ACCORDANCE WITH MIL-STD-129R WITH CHANGE 3, AND DLA TROOP SUPPORT C&T AQAR dated 1 August 2021.

END ITEM VISUAL INSPECTION LEVEL SHALL BE II AND THE ACCEPTABLE QUALITY LEVEL (AQL), EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE 1.0 FOR MAJOR DEFECTS AND 10.0 FOR TOTAL (MAJOR AND MINOR COMBINED) DEFECTS. SAMPLE UNIT SHALL BE ONE (1) PAIR OF TROUSERS.

END ITEM DIMENSIONAL INSPECTION LEVEL SHALL BE S-3 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE 2.5. SAMPLE UNIT SHALL BE ONE (1) PAIR OF TROUSERS.

END ITEM TESTING INSPECTION LEVEL SHALL BE S-2 AND AQL, EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE 4.0 FOR TEST FAILURES. SAMPLE UNIT SHALL BE ONE (1) PAIR.

PACKAGING INSPECTION LEVEL SHALL BE S-2 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE 2.5. SAMPLE UNIT SHALL BE ONE (1) SHIPPING CONTAINER FULLY PACKAGE.

PALLETIZATION INSPECTION LEVEL SHALL BE S-1 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE 4.0 IN ACCORDANCE WITH ANZI/ASQC Z 1.4.