SPECIFICATIONS_FOR_COMPACT_TRACK_LOADER4.pdf
PDF 29 KB Posted
- Attached to
- 165-20260212140934 BSWC
- Solicitation number
- 3170035060
- Issued by
- Wayne County, Mississippi
About this file
This document is a specifications sheet issued by the Walthall County Board of Supervisors in Mississippi for the procurement of one or more new or unused compact track loaders. The specifications establish performance and quality standards intended to allow competitive bidding without unnecessarily excluding manufacturers, permitting comparable products and substitutions that meet the defined requirements. The compact track loader specifications include an engine rated at 73 horsepower with a turbocharged diesel engine displacing 3.319 liters, operating at 2,400 rpm with peak torque of 206 lbf-ft, and meeting Tier 4 Final/Stage V emissions standards. The equipment must have a rated operating capacity of 2,579 pounds, tipping load of 7,368 pounds, and operating weight of 10,318 pounds, with a maximum breakout force of 5,733 lbf. Additional specifications address hydraulic systems (3,336 psi pressure, 21 gpm standard flow or 31.6 gpm high flow), transmission (one-speed 5.4 mph or two-speed 8.5 mph), 12-volt battery systems, and 26.4-gallon fuel capacity. Dimensional specifications include maximum overall height of 156 inches, ground clearance of 9 inches, and turning radius from center-machine rear of 66.3 inches.
The procurement specifications also include optional equipment in the form of a six-way dozer blade available in 72-inch, 84-inch, and 96-inch widths with electro-hydraulic angle control, tilt capability of up to 100 degrees, and lateral angle adjustment of 30 degrees. The blade features a 10-gauge rolled steel moldboard with a heavy 1/2-inch replaceable steel cutting edge and is recommended for skid steers over 50 horsepower. The County explicitly states that its intention is to solicit competitive bids on comparable equipment and that any references to specific manufacturers are intended only to establish acceptable standards, not to limit bidding. Bidders are required to identify any bid items that are not compliant with the stated specifications.
View the file
Other files
Show all 14
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
IF BID IS NOT COMPLIANT, STATE SPECIFICALLY ITEM BEING OFFERED. IT IS THE
INTENTION OF THE WALTHALL COUNTY BOARD OF SUPERVISORS TO SOLICIT
COMPETITIVE BIDS ON COMPARABLE EQUIPMENT SO AS TO NOT EXCLUDE
VENDORS BY NARROWLY DRAWING THESE SPECIFICATIONS.
The following are the suggested approximate specifications for one or more new or unused compact track loaders. All bids must be equal in performance and quality pursuant to the bid specifications below, which are not intended to exclude any manufacturer's standard deviation. Any reference to manufacture's make or series of equipment stated in the following specifications is intended only to establish an acceptable standard and is not intended to limit the bidding and comparable products may be substituted.
TRACK LOADER:
Engine Speed 2,400 rpm Rated Power 73 hp Peak Torque 206 lbf-ft at 1,560 rpm Displacement 3.319 L Aspiration Turbocharged Emissions Tier 4 Final/Stage V Cycle Time (Raise/Lower/Dump) 9s Loader Hydraulic Pressure 3,336 psi Battery Voltage 12V Diesel Tank 26.4 gal Rated Operating Capacity2,579 lbs Tipping Load 7,368 lbs Operating Weight 10,318 lbs Max Breakout Force 5,733 lbf Lift Geometry Vertical Lift One Speed 5.4 mph Two Speed 8.5 mph Rubber Track Size 320 mm, 400 mm each in two patterns Standard Flow 21 gpm High Flow 31.6 gpm Maximum Overall Height 156" Bucket Pin Height at Maximum Lift 120.5" Clearance at Maximum Lift and Dump 92" Ground Clearance 9" Track Length on Ground 57.5" Bumper Overhang Behind Rear Axle 34.8" Maximum Dump Angle 40 degrees Rollback Angle of Bucket on Ground 30 degrees Departure Angle 28 degrees Height to Top of Cab 82.7" Length with Bucket on Ground 142.1" Reach at Maximum Lift and Dump 42" Length Without Bucket 113.6" Turning Radius from Center-Bucket 82.7" Turning Radius from Center-Machine Rear 66.3"
Width with Bucket 72" Width Without Bucket 70"
SIX WAY DOZER BLADE:
Options on 72", 84" and 96" widths 6-Way Control: Tilt up/down 100 degrees; angle left/ right 30 degrees for precise grading & contour work 22" blade height with optional 8" extension for increased capacity 10-gauge rolled steel moldboard Reinforced steel boxed frame design Heavy 1/2" replaceable steel cutting edge Electro-Hydraulic angle control with double hydraulic cylinders Trip lockout function for dirt work Optional trip springs for snow removal Recommended for skid steers over 50 HP Requires Universal Control or OEM wiring harness Universal skid steer mount
File details come from the government source that posted it. Updated .