SF30_SPE1C124R00840001-Updted Tech CGTrunks-AttachB-9-6-24.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

1. CONTRACT ID CODE

2. AMENDMENT/MODIFICATION NO.

See Block 14

4. REQUISITION/PURCHASE REQ. NO. 5. PROJECT NO. (If applicable)

6. ISSUED BY CODE SPE1C1 7. ADMINISTERED BY (If other than Item 6) CODE

8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, State and ZIP Code)

CODE FACILITY CODE

SPE1C124R0084

X

2024 AUG 26

10A. MODIFICATION OF CONTRACT/ORDER NO.

10B. DATED (SEE ITEM 13)

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of OffersX is extended, X is not extended.

or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended, by one of the following methods:

12. ACCOUNTING AND APPROPRIATION DATA (If required)

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT ORDER NO.

IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc. ) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A NAME AND TITLE OF SIGNER (Type or print)

NSN 7540-01-152-8070

Previous edition unusable

STANDARD FORM 30 (REV. 10-83)

Prescribed by GSA FAR (48 CFR) 53.243

16B. UNITED STATES OF AMERICA15B. CONTRACTOR/OFFEROR

(Signature of Contracting Officer)(Signature of person authorized to sign)

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

(a) By completing Items 8 and 15, and returning

DLA TROOP SUPPORT

C AND T SUPPLY CHAIN

700 ROBBINS AVENUE

PHILADELPHIA PA 19111-5096

15C. DATE SIGNED 16C. DATE SIGNED

D. OTHER (Specify type of modification and authority)

9/6/2024

3. EFFECTIVE DATE

See Attached Continuation Sheet(s).

(X)

CHECK ONE

9A. AMENDMENT OF SOLICITATION NO.

9B. DATED (SEE ITEM 11)

13. THIS APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED:

CONTINUED ON NEXT PAGE

PAGE 2 OF 8 PAGES

SPE1C124R0084 - 0001

REFERENCE SOLICITATION SPE1C1-24-R-0084:

The following changes apply to specification data and technical data:

1. Attachment B for chevron measurements is hereby added as an attachment to Amendment 0001.

2. The technical data for the Coast Guard Trunks is hereby updated and replaces the technical data document sent with the original solicitation document in full text below and as an attachment to Amendment 0001.

3. Closing date for solicitation remains the same: September 25, 2024 @ 3:00 PM, local (Philadelphia) time - Eastern Standard Time (Philadelphia time), or when applicable, Eastern Daylight Savings Time.

TECH-DATA PGC00108 9/05/2024

NSN 8415016616920

TRUNKS UTILITY (TRUNKS GENERAL PURPOSE WITHOUT AF LOGO)

TYPE II, COAST GUARD.

SHALL BE MADE IN ACCORDANCE

WITH CRFD/PD 04-07 REVISION D

DATED 30 September 2010

PATTERN DATE JULY 15, 2010.

STANDARD SAMPLE FOR BASIC MATERIAL:

AIR FORCE BLUE SHADE 1650, IDENTIFIED AS ROLL

NO. 10-04 FOR SHADE ONLY.

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.

mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE

AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ009: INSPECTION AND ACCEPTANCE AT DESTINATION

SHALL BE MADE IN ACCORDANCE WITH

TRUNKS, IMPROVED PHYSICAL TRAINING, UNIFORM,

CRFD/PD 04-07 REVISION D, DATED 30 SEPTEMER 2010

RETAIN INVERTED CHEVRON REFLECTIVE LINE DESIGN

HEAT TRANSFER PATTERN POSITIONED OVER THE OUTSEAM OF THE SHORTS.

OMIT THE REFLECTIVE AIR FORCE WING LOGO.

PATTERN DATE JULY 15, 2010.

STANDARD SAMPLE FOR BASIC MATERIAL:

AIR FORCE BLUE SHADE 1650, IDENTIFIED AS ROLL

NO. 10-04 FOR SHADE ONLY.

INTERIM CHANGES TO CRFD/PD 04-07 REVISION D.

PARA 1.1 CLASSIFICATION: AFTER SHALL BE OF DELETE "ONE TYPE", AND CHANGE TO: "TYPE I - AIR FORCE".

AND ADD "TYPE II - COAST GUARD, WOTHOUT AIR FORCE LOGO

SIZES: SMALL, MEDIUM,

LARGE, AND X-LARGE"

Page 3, Paragraph 3.3. Description. Line 6, delete "(See Figures 3 and 4)' and substitute "(see figure 3,4, 5 and 6). All figures are for reference only, not to scale".

Para. 3.3.1 Sewing instructions.: line 2, before "1/4" add "1/8 to".

Para. 3.3.1 Sewing instructions.: Line 25, delete "1/4" and substitute 1-1/4".

Page 4, Table II Stitches and placement.: Attachment of pocket to side seam.: under "Seam Type" delete SSc-2" and substitute "SSa-1"

Page 4, Table II Stitches and placement.: Attachment of I.D. pocket to vent.: under "Seam Type" delete SSc-2" and substitute "SSa-1"

Page 4, Table II. Stitches Placement. Line 1, delete "crotch" and substitute "rise."

PAGE 3 OF 8 PAGES

Page 4, Table II Stitches and placement.: Line 7, under :"Seam Type" after "LSd-1" add "or SSa-1"

Page 4, Table II Stitches and placement.: Line 8, under :"Seam Type" delete "SSa-1" and substitute "SSa-2".

Page 7, para 3.5.3.1 Waist. Line 1, after "1 ¼" add to "1 ½".

ADD THE FOLLOWING:

"THE CLOTH SHALL BE TESTED FOR THE CHARACTERISTICS

LISTED IN TABLE III, USING THE METHODS OF

TESTING SPECIFIED HEREIN. THE SAMPLE UNIT SHALL

BE 3 CONTINUES YARDS FULL WIDTH. THE LOT SHALL

BE UNACCEPTABLE IF ONE OR MORE UNITS OR THE LOT

AVERAGE FAIL TO MEET ANY TEST REQUIREMENT SPECIFIED.

THE SAMPLE SIZE SHALL BE IN ACCORDANCE

WITH THE FOLLOWING:

LOT SIZE (YARDS) SAMPLE SIZE (SAMPLE UNITS)

800 OR LESS 2

801 UP TO AND INCLUDING 22,000 3

22,000 AND OVER 5".

Page 9, paragraph 3.6.1 Certification. Delete in its entirety.

Page 20, Figure 3. Air Force Symbol and Air Force Text for trunks delete entirely and substitute the new Page 20 (SEE ATTACHMENT B)

Page 22, Figure 5. One piece chevron, delete entirely and substitute the new Page 22, Figure 5. One Piece Chevron (SEE ATTACHMENT B)

Add Page 23, Figure 6. Left Leg Chevron and U.S. Air Force Symbol & Text. (SEE ATTACHMENT B)

Page 23, Figure 6. Tolerance block A, delete "(+/- 0.125")" and substitute "(+/- 0.375")". (SEE ATTACHMENT B)

AQLS SHALL BE AS FOLLOWS:

END ITEM DIMENSIONAL 4.0 - INSPECTION LEVEL S-3

VISUAL 4.0 - INSPECTION LEVEL II

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

USE OF "SAMPLING PROCEDURES AND TABLES FOR

INSPECTION BY ATTRIBUTES". ANSI/ASQC Z1.4.

EACH TRUNK SHALL BE NEATLY FOLDED AND INSERTED

IN A CLOSE-FITTING CLEAR POLYETHYLENE BAG.

SEVENTY TWO TRUNKS OF ONE SIZE SHALL BE PACKED

IN A SNUG FITTING FIBERBOARD SHIPPING CONTAINER

CONFORMING TO ASTM-D5118, TYPE CF, STYLE RSC-L

(LINER), GRADE 275. VARIETY SW. CLASS DOMESTIC.

APPROXIMATE BOX DIMENSIONS ARE FURNISHED AS A

GUIDE ONLY: LENGTH 23-1/2 INCHES, WIDTH 15

INCHES AND DEPTH 15 INCHES.

THE FOLLOWING REQUIREMENTS ARE IN ACCORDANCE

WITH ASTM D1974 METHODS OF CLOSING, SEALING AND

REINFORCING FIBERBOARD BOXES. CLOSURE METHOD

SHALL BE 2A2, FIGURE 1, OR AS AN ALTERNATE,

2B6 OR 2B7, FIGURE 3.

WIDTH. THE LOT SHALL BE UNACCEPTABLE IF ONE OR

MORE UNITS OR THE LOT AVERAGE FAIL TO MEET ANY

TEST REQUIREMENT SPECIFIED. THE SAMPLE SIZE

SHALL BE IN ACCORDANCE WITH THE FOLLOWING:

ADD THE FOLLOWING TO SECTION D OF THE CONTRACT:

"PACKAGING EXAMINATION: THE FULLY PACKAGED END

ITEM SHALL BE EXAMINED FOR THE DEFECTS LISTED

BELOW. THE LOT SIZE SHALL BE EXPRESSED IN UNITS

OF SHIPPING CONTAINERS. THE SAMPLE UNIT SHALL

BE ONE SHIPPING CONTAINER FULLY PACKAGED. THE

INSPECTION LEVEL SHALL BE S-2 AND THE AQL,

EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS,

SHALL BE 2.5.

EXAMINE DEFECT

MARKING (EXTERIOR OMITTED; INCORRECT;

AND INTERIOR) ILLEGIBLE; OF IMPROPER SIZE;

. LOCATION SEQUENCE, OR

. METHOD OF APPLICATION.

MATERIALS ANY COMPONENT MISSING,

. DAMAGED, OR NOR AS SPECIFIED

WORKMANSHIP INADEQUATE APPLICATION OF

. COMPONENTS SUCH AS : CLOSURE

PAGE 4 OF 8 PAGES

. OF CONTAINER FLAPS, LOOSE

. STRAPPING, IMPROPER TAPING,

. INADEQUATE STAPLING, BULGED

. OR DISTORTED CONTAINER.

CONTENTS NUMBER OF INTERMEDIATE

. CONTAINERS PER SHIPPING

. CONTAINER IS MORE OR LESS

. THAN REQUIRED, MIXED SIZES

. OR INCORRECT SIZE."

SHADE EVALUATION OF CONTRACTOR FURNISHED The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/-200) °K , with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200) °K.

All shade submittals shall be submitted along with the instrumental numbers s which co-correspond to the rolls sent in for visual shade evaluation. A protocol has been established on how the Standard and Samples will be read.

Instrumental values will be correlated by the DLA Product Testing Center and the contractor to make sure that the values are similar.

Protocol for Measurement of Shade Samples

1. AATCC Evaluation Procedure 6 - Instrumental Color Measurement, Section 2 - Measurement of Color by Reflectance Methods, should be used as a guideline in conjunction with AATCC Test Method 173 CMC: Calculation of Small Color Differences for Acceptability.

2. The samples should be clean and free of lint.

3. The spectrophotometer should be properly calibrated to manufacturers' specifications prior to taking measurements, using the green tile.

4. The following parameters should be used for measuring the samples:

Illuminant: D65 Area View: Large Observer: 10 Mode: Specular Included - Reflectance UV Filter - OUT UV Lamp OFF Scale: CIELAB

Samples should be backed with three layers and should be measured three times and averaged.

5. The samples should be identified as follows:

Standard (color name) Tolerance (descriptor) Samples 1-10

The absolute L* a* b* values for the standard should be recorded and printed. The absolute L* a* b* and the DE cmc 2:1 DL* Da* and Db* for all tolerances and all samples compared to the standard should be recorded and printed."

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED 18 FEBRUARY 2014

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH

PAGE 5 OF 8 PAGES

DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS

SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL

SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

THE GOVERNMENT ASSIGNED UNIVERSAL PRODUCT

CODE (UPC) MUST BE PLACED ON ALL SHIPPING

CARTONS ON WHICH THE NSN APPEARS".

PACKAGING

PRES/PACK TO ASTM-D-3951

CARTONS SHALL BE STYLE RSC, GRADE 275,

VARIETY SW WITH DW LINERS, GRADE 275

SHIPPING CONTAINER QUANTITY = 72

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged.

The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking Omitted; incorrect; illegible, of (exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Examine Defect

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, sequence or method of appli-cation.

252.211-7006 - RADIO FREQUENCY IDENTIFICATION (RFID) Required

PAGE 6 OF 8 PAGES

(ref. T8379; Nov. 08, 2006)

RFID HANGTAG:

An RFID inlay shall be added to the barcode paper hang tag attached to each item. Where the use of self-adhesive bar-code labels are authorized, the RFID inlay may be added to the self-adhesive label in lieu of a paper hang tag. All other contract barcode and hang tag requirements still apply.

The RFID inlay should be passive Gen2 with a frequency range between 860 and 960 MHz. The RFID antenna should be Avery/Dennis AD222 or comparable with ISO/IEC 18000-C EPCglobal C1G2 Protocol and an EPC memory allocation containing a 96 bit EPC Number. The data linking the EPC number to the NSN and quantity unit pack must be exportable to VIM/ ASAP. The bar code of the EPC Number must be printed at the bottom of the tag along with the human readable version below the bar code.

In addition to defects applicable to the paper tag and barcoding element, the RFID tag shall be examined for the defects listed below:

RFID Inlay omitted RFID Inlay not secure RFID Inlay not laying flat when packaged RFID Inlay not readable with RFID scanner RFID Inlay or configuration not as specified

The manual "Item-Level Passive RFID Technology Manufacturer's Information Guide" provides guidance on RFID implementation and is available from the contracting officer.

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable.

Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES

IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL

QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER

THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

PAGE 7 OF 8 PAGES

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENTOF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006)

CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 8 OF 8 PAGES

Attachments

List of Attachments

Description File Name

ATTACH_CRFDPD_04_07

D_Attachment_B

CRFDPD 04-07D IPTU-

Attachment B.pdf ATTACH_Tech_Data_CG_

Trunks_Updtd_9_5_24 Techdata-Trunks CG- Updted- 9.5.2024.pdf

PID Data - Custom Clause

Header C1